Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 4
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Fine-grained BCZT piezoelectric ceramics by combining high-energy mechanochemical synthesis and hot-press sintering

  • Sayagués, M. J.
  • Otero, A.
  • Santiago-Andrades, L.
  • Poyato, R.
  • Monzón, M.
  • Paz, R.
  • Gotor, F.J.
  • Moriche, R.
Different stoichiometries of lead-free BaZr0.2Ti0.8O3–Ba0.7Ca0.3TiO3 (BCZT) prepared by mechanosynthesis and sintered by either conventional sintering (CS) or hot pressing (HP) techniques were studied to establish the dependence of piezoelectric and dielectric properties on sintering parameters and microstructure. All synthesized stoichiometries showed a pseudocubic perovskite phase with homogeneously distributed A- and B-cations in the structure. The BCZT retained the pseudocubic symmetry after sintering and an average grain size <1.8 µm was obtained in all cases. HP sintering hindered the secondary phase segregation observed in the CS ceramics and increased the relative density. Piezoelectric coefficients (d33) ranging from 5.1 to 21 pC/N and from 10.0 to 88.0 pC/N were obtained for CS and HP ceramics, respectively, despite the pseudocubic symmetry and the fine grain size. The higher d33 values for the HP ceramics are a consequence of the higher density, better chemical homogeneity and lower sintering temperature and time required for the mechanosynthesized BCZT powders with high sintering activity., The authors acknowledge the grant TED2021–131458A-I00 funded by MICIU/AEI/ 10.13039/501100011033 and by the “European Union NextGenerationEU/PRTR”; and the grant PID2020–117648RB-I00 funded by MICIU/AEI/10.13039/501100011033., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Piezoelectric and Dielectric Response of BaTiO3/PVDF-TrFE Composites with High β‑Phase Content

  • Otero, Andrea
  • Sayagués, María Jesús
  • Romero, Francisco Javier
  • Gotor, F.J.
  • Moriche, Rocío
The search for flexible piezoelectric materials to build adaptable sensors, electronics, and nanogenerators has become a key area of interest. The addition of piezoceramic particles to piezoelectric polymers, such as the copolymer poly-(vinylidene fluoride-trifluoroethylene) (PVDF-TrFE), is one of the strategies used to enhance the piezoelectric response. In this work, the effect of BaTiO3 content on the β-phase formation, crystallization, and piezoelectric and dielectric properties of the polymer-based composites is investigated. High-energy ball milling was used as an effective, greener technique to achieve well-dispersed mixtures compared to those obtained using organic solvents. During the dispersion process, amorphization and reduction of the crystalline domain size occur. After compression molding and postprocessing, the crystallinity was recovered and was strongly dependent on the filler content. Although significant differences in the β-phase fraction were not observed, conformational defects are induced with high BaTiO3 contents. The interlayer distances became smaller due to the presence of the ceramic particles after compression molding and remained almost unchanged after postprocessing. For the composites, the minimum voltage required to obtain a measurable piezoelectric coefficient (d 33 ) was significantly reduced compared to neat PVDF-TrFE, even for low contents, which is key for real applications. Three different piezoelectric behaviors were found depending on the BaTiO3 fraction. For composites with 40 vol %, where both matrix and filler contribute to the overall piezoelectric response, the use of a two-step poling method induced a synergistic effect with an increase in d 33 of ∼180%. However, the relaxation of the ceramic contribution after 24 h returns the value of d 33 to that obtained by applying a one-step poling strategy., This contribution is part of the project TED2021-131458A-I00, funded by MCIN/AEI/10.13039/501100011033 and by the Unión Europea NextGenerationEU/PRTR., The authors declare the following competing financial interest(s): Rocio Moriche reports financial support was provided by Ministerio de Ciencia, Innovacin y Universidades. If there are other authors, they declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper. Acknowledgments, Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

High piezoelectric performance in lead-free BCHT fine-grained ceramics synthesized by mechanochemistry

  • Santiago-Andrades, L.
  • Romero, F. J.
  • Gotor, F.J.
  • Sayagués, M. J.
  • Moriche-Tirado, Rocío.
Lead-free piezoelectric ceramics (Ba<inf>1-x</inf>Ca<inf>x</inf>) (Ti<inf>1-y</inf>Hf<inf>y</inf>)O<inf>3</inf> with stoichiometries close to the morphotropic phase boundary (MPB) were synthesized by high-energy ball milling. The influence of Hf and Ca contents and the sintering method (conventional and hot-press) on the piezoelectric, dielectric, and ferroelectric response was investigated. It was confirmed that the different phases stabilized at room temperature and the structural distortion are strongly dependent on the stoichiometry. The coexistence of tetragonal, orthorhombic and rhombohedral phases was observed in samples with the lowest Ca and Hf contents. These samples, which are in the MPB region, also showed the greatest structural distortion, resulting in higher values of d<inf>33</inf>. Samples with lower Hf content exhibited a higher coercive field, remnant polarization, and temperature in the ferroelectric to paraelectric transition. Despite the high sintering temperature leading to high densification, grain growth during sintering was limited because of the use of mechanochemically synthesized powders. Although Ba<inf>0.85</inf>Ca<inf>0.15</inf>Hf<inf>0.10</inf>Ti<inf>0.90</inf>O<inf>3</inf> stoichiometry has been reported in the literature as the best for piezoelectric properties, in this work, BCHT solid solution with the lowest dopant content studied (Ba<inf>0.90</inf>Ca<inf>0.10</inf>Hf<inf>0.05</inf>Ti<inf>0.95</inf>O<inf>3</inf>) showed the best combination of functional properties. Ceramics of this composition with grain size <2 μm exhibited a d<inf>33</inf> > 250 pC/N, with almost no relaxation after 24 h, and the highest permittivity. In the field of piezoelectric materials, there is considerable interest in reducing grain size while maintaining high piezoelectric performance, as this can lead to improvements in mechanical properties., The authors acknowledge the grant TED2021-131458 A-I00 funded by MICIU/AEI/10.13039/501100011033 and by the “European Union NextGenerationEU/PRTR”; and L. Santiago-Andrades acknowledges a JAE-Intro fellowship from the Spanish National Research Council (CSIC) and a student fellowship from the University of Seville., Peer reviewed
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Critical role of phosphorus in hollow structures cobalt-based phosphides as bifunctional catalysts for water splitting, High-performance bifunctional hollow structures cobalt-based phosphides catalysts for water splitting

  • Zhang, Wei
  • Han, Ning
  • Luo, Jiangshui
  • Han, Xu|||0000-0001-8319-8830
  • Feng, Shihui
  • Guo, Wei|||0000-0002-4322-3699
  • Xie, Sijie
  • Zhou, Zhenyu
  • Subramanian, Palaniappan|||0000-0003-1000-6994
  • Wan, Kai|||0000-0003-4689-310X
  • Arbiol i Cobos, Jordi|||0000-0002-0695-1726
  • Zhang, Chi|||0000-0001-6009-5273
  • Liu, Shaomin
  • Xu, Maowen|||0000-0001-9320-5731
  • Zhang, Xuan
  • Fransaer, Jan|||0000-0002-0232-0687
Cobalt phosphides electrocatalysts have great potential for water splitting, but the unclear active sides hinder the further development of cobalt phosphides. Wherein, three different cobalt phosphides with the same hollow structure morphology (CoP-HS, CoP-HS, CoP-HS) based on the same sacrificial template of ZIF-67 are prepared. Surprisingly, these cobalt phosphides exhibit similar OER performances but quite different HER performances. The identical OER performance of these CoP-HS in alkaline solution is attributed to the similar surface reconstruction to CoOOH. CoP-HS exhibits the best catalytic activity for HER among these CoP-HS in both acidic and alkaline media, originating from the adjusted electronic density of phosphorus to affect absorption-desorption process on H. Moreover, the calculated ΔG based on P-sites of CoP-HS follows a quite similar trend with the normalized overpotential and Tafel slope, indicating the important role of P-sites for the HER process. Moreover, CoP-HS displays good performance (cell voltage of 1.67 V at a current density of 50 mA cm) and high stability in 1 M KOH. For the first time, this work detailly presents the critical role of phosphorus in cobalt-based phosphides for water splitting, which provides the guidance for future investigations on transition metal phosphides from material design to mechanism understanding.