Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 9
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Effect of Laccase Detoxification on Bioethanol Production from Liquid Fraction of Steam-Pretreated Olive Tree Pruning

  • Ibarra, David
  • Eugenio, María E.
  • Alvira, Pablo
  • Ballesteros, Ignacio
  • Ballesteros, Mercedes
  • Negro, María José
14 Pág., During lignocellulosic bioethanol production, the whole slurry obtained by steam explosion is filtered, generating a water-insoluble fraction rich in cellulose which is used for saccharification and ethanol fermentation, as well as a liquid fraction containing solubilised glucose and xylose but also some inhibitory by-products (furan derivatives, weak acids and phenols), which limits its use for this purpose. Since utilization of this liquid fraction to ethanol is essential for an economically feasible cellulosic ethanol process, this work studied a laccase from Myceliophthora thermophila to detoxify the liquid fraction obtained from steam-pretreated olive tree pruning (OTP) and to overcome the effects of these inhibitors. Then, the fermentation of laccase-treated liquid fraction was evaluated on ethanol production by different Saccharomyces cerevisiae strains, including the Ethanol Red, with the capacity to ferment glucose but not xylose, and the xylose-fermenting recombinant strain F12. Laccase treatment reduced total phenols content by 87% from OTP liquid fraction, not affecting furan derivatives and weak acids concentration. Consequently, the fermentative behavior of both Ethanol Red and F12 strains was improved, and ethanol production and yields were increased. Moreover, F12 strain was capable of utilizing some xylose, which increased ethanol production (10.1 g/L) compared to Ethanol Red strain (8.6 g/L)., This research was funded by Comunidad de Madrid via Project SUSTEC‐CM S2018/EMT‐ 4348; Spanish MCINN/AEI/10.13039/501100011033 and by “ERDF A way of making Europe” via Project RTI2018‐096080‐B‐C22; and Spanish MCINN via Project TED2021‐132122B‐C21. In addition, part of the experimental work has been carried out in the framework of the project financed by Spanish MICINN (ENE2011-29112-C02-01)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Enzyme-Catalyzed Polymerization of Kraft Lignin from Eucalyptus globulus: Comparison of Bacterial and Fungal Laccases Efficacy

  • García-Fuentevilla, Luisa
  • Domínguez, Gabriela
  • Martín-Sampedro, Raquel
  • Hernández, Manuel
  • Arias, María Enriqueta
  • Santos, José I.
  • Ibarra, David
  • Eugenio, María E.
  • Arias, María Enriqueta
20 Pág., Kraft lignin, a side-stream from the pulp and paper industry, can be modified by laccases for the synthesis of high added-value products. This work aims to study different laccase sources, including a bacterial laccase from Streptomyces ipomoeae (SiLA) and a fungal laccase from Myceliophthora thermophila (MtL), for kraft lignin polymerization. To study the influence of some variables in these processes, a central composite design (CCD) with two continuous variables (enzyme concentration and reaction time) and three levels for each variable was used. The prediction of the behavior of the output variables (phenolic content and molecular weight of lignins) were modelled by means of response surface methodology (RSM). Moreover, characterization of lignins was performed by Fourier-transform infrared (FTIR) spectroscopy and different nuclear magnetic resonance (NMR) spectroscopy techniques. In addition, antioxidant activity was also analyzed. Results showed that lignin polymerization (referring to polymerization as lower phenolic content and higher molecular weight) occurred by the action of both laccases. The enzyme concentration was the most influential variable in the lignin polymerization reaction within the range studied for SiLA laccase, while the most influential variable for MtL laccase was the reaction time. FTIR and NMR characterization analysis corroborated lignin polymerization results obtained from the RSM., This research was funded by Comunidad de Madrid via Project SUSTEC-CM S2018/EMT-4348; MICINN/AEI/10.13039/501100011033 and by “ERDF A way of making Europe” via Project RTI2018-096080-B-C22; and MICINN via Project TED2021-132122B-C21., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

NMR Study on Laccase Polymerization of Kraft Lignin Using Different Enzymes Source

  • Ibarra, David
  • García-Fuentevilla, Luisa
  • Domínguez, Gabriela
  • Martín-Sampedro, Raquel
  • Hernández, Manuel
  • Arias, María Enriqueta
  • Santos, José I.
  • Eugenio, María E.
17 Pág., The usage of laccases is a sustainable and environmentally friendly approach to modifying the Kraft lignin structure for use in certain applications. However, the inherent structure of Kraft lignin, as well as that resulting from laccase modification, still presents challenges for fundamental comprehension and successful lignin valorization. In this study, bacterial and fungal laccases were employed to modify eucalypt Kraft lignin. To evaluate the type and range of the chemical and structural changes of laccase-treated lignins, different NMR techniques, including solution 1H and 2D NMR (heteronuclear single quantum correlation (HSQC)), and solid-state 13C NMR, were applied. Size exclusion chromatography and infrared spectroscopy were also used. Interestingly, HSQC analysis showed substantial changes in the oxygenated aliphatic region of lignins, showing an almost complete absence of signals corresponding to side-chains due to laccase depolymerization. Simultaneously, a significant loss of aromatic signals was observed by HSQC and 1H NMR, which was attributed to a deprotonation of the lignin benzenic rings due to polymerization/condensation by laccase reactions. Then, condensed structures, such as α-5', 5-5', and 4-O-5', were detected by HSQC and 13C NMR, supporting the increment in molecular weight, as well as the phenolic content reduction determined in lignins., This research was funded by Comunidad de Madrid via Project SUSTEC-CM S2018/EMT-4348; MCINN/AEI/10.13039/501100011033 and by “ERDF A way of making Europe” via Project RTI2018-096080-B-C22; and MCINN via Project TED2021-132122B-C21., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Green solvents extraction-based detoxification to enhance the enzymatic hydrolysis of steam-exploded lignocellulosic biomass and recover bioactive compounds

  • Cañadas, Raquel
  • Martín-Sampedro, Raquel
  • González-Miquel, María
  • González, Emilio J.
  • Ballesteros, Ignacio
  • Eugenio, María E.
  • Ibarra, David
11 Pág., A novel strategy for pre-treated biomass detoxification combining emerging green solvents and low environmental impact extraction technologies was evaluated. Steam-exploded biomass was subjected to microwave-assisted or orbital shaking extraction using bio-based or eutectic solvents. The extracted biomass was enzymatically hydrolysed. The potential of this detoxification methodology was studied in terms of phenolic inhibitors extraction and sugar production improvement. The effect of adding a post-extraction water washing step before hydrolysis was also evaluated. Excellent results were achieved when steam-exploded biomass was subjected to the microwave-assisted extraction combined with the washing step. The highest sugar production was achieved when ethyl lactate was used as extraction agent (49.80 ± 3.10 g total sugar/L) over the control (30.43 ± 0.34 g total sugar/L). Results suggested that a detoxification step based on green solvents would be a promising option to extract phenolic inhibitors, which can be revalorized as antioxidants, and improve the sugar production from the extracted pre-treated biomass., The authors are grateful to Comunidad Autónoma de Madrid (Spain) for funding the project SUSTEC S2018/EMT-4348 and MCIN for funding the project TED 2021-132122 B–C21. Raquel Martín-Sampedro, María E. Eugenio and David Ibarra are grateful for the support of the Interdisciplinary Platform for Sustainable Plastics towards a Circular Economy-Spanish National Research Council (SusPlast-CSIC), Madrid, Spain and Interdisciplinary Platform for Sustainability and Circular Economy (SosEcoCir-CSIC). The authors from UPM acknowledge Comunidad Autónoma de Madrid (Spain) for funding under the Multiannual Agreement with Universidad Politécnica de Madrid in the line Excellence Programme for University Professors, in the context of the V PRICIT (Regional Programme of Research and Technological Innovation)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Kraft lignins from different poplar genotypes obtained by selective acid precipitation and their use for the production of electrospun nanostructures

  • Ibarra, David
  • García-Fuentevilla, Luisa
  • Rubio-Valle, José F.
  • Martín-Sampedro, Raquel
  • Valencia, Concepción
  • Eugenio, María E.
13 Pág., Kraft lignins from different poplar genotypes (Populus alba L. “PO-10-10-20” and Populus x canadensis “Ballotino”) were isolated by selective acid precipitation (pH 5 and 2.5), chemically and structurally characterized and used together with cellulose acetate (CA) for the manufacture of nanostructures by electrospinning. Generally, lignins showed a predominance of β-β´ resinols substructures (4.7–5.3 linkages per 100 aromatic units) followed by β-O-4´ (1.6–3.3 linkages per 100 aromatic units) and β-5´ phenylcoumarans (0.5–2.4 linkages per 100 aromatic units) and a high abundance of S lignin units (S/G 3.0–4.3). Moreover, lignins showed low molecular weight values (between 5.14 and 5.59 KDa) and high phenolic content (529.1 –644.5 mg GAE/g lignin). Regarding the electrospun nanostructures obtained from Kraft lignins/CA solutions, all of them presented uniform cross-linked nanofibers with a few beaded fibers according to the suitable range values of surface tension (29.18–29.71 mN/cm), electrical conductivity (131.2–158.9 μS/cm) and dynamic viscosity (0.28–0.32 Pa.s) that biopolymer solutions showed. Nevertheless, electrospun Kraft lignins/CA nanostructures with larger mean diameters were generated from lignins at pH 5, which displayed higher phenolic and β-O-4´ contents compared to lignins at pH 2.5. On the other hand, the type of poplar lignin genotype did not exert a significant influence on the mean fiber diameter., This work is part of two coordinated research projects (RTI2018-096080-B-C21 and RTI2018-096080-B-C22) funded by MCIN/AEI/10.13039/501100011033 and by “ERDF A way of making Europe”. The authors also wish to thank the Comunidad de Madrid and MCIN/AEI/FEDER, EU for funding this study via Projects SUSTEC-CM S2018/EMT-4348 and TED2021-132122B-C21, respectively. The authors also acknowledge the pre-doctoral grants from José Fernando Rubio Valle (Ref. PRE2019-090632)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Boosting enzymatic hydrolysis of steam-pretreated softwood by laccase and endo-β-mannanase enzymes from Streptomyces ipomoeae CECT 3341

  • Eugenio, María E.
  • Domínguez, Gabriela
  • Molina-Guijarro, José M.
  • Hernández, Manuel
  • Arias, María Enriqueta
  • Ibarra, David
23 Pág., Ligninases and hemicellulases are crucial as accessory enzymes to increase the enzymatic hydrolysis of lignocellulose, boosting sugars production from which biofuels and bioproducts could be obtained. In order to find new sources of these accessory enzymes, this study evaluates the potential of laccase and mannanase enzymes from Streptomyces ipomoeae for improving the conventional hydrolysis with commercial cellulases of steam-pretreated softwood. For that, different laccase treatment and mannanase supplementation strategies were performed. S. ipomoeae laccase increased both glucose and xylose production (17.8% and 9.3%, respectively), which was attributed to a removal of phenols of 29%. Moreover, the combination of laccase and alkaline extraction produced a lignin reduction of 16.2%, improving the glucose and xylose production by almost 41.3% and 44.9%, respectively. On the other hand, the supplementation of S. ipomoeae mannanase to the hydrolysis 24 h before the addition of cellulases increased the glucose (18.4%), xylose (12.3%), and mannose (47.2%) production., This research was funded by Comunidad de Madrid via Project SUSTEC‐CM S2018/EMT‐ 4348; Spanish MCINN/AEI/10.13039/501100011033 and by “ERDF A way of making Europe” via Project RTI2018‐096080‐B‐C22; and Spanish MCINN via Projects TED2021‐132122B‐C21 (LIGNUCELL) and PID2022-141965OB-C21 (SUS-BIO-FILM). María E. Eugenio and David Ibarra are grateful for the support of the Interdisciplinary Platform for Sustainable Plastics toward a Circular Economy (SusPlast-CSIC), Madrid, Spain and Interdisciplinary Platform for Sustainability and Circular Economy (SosEcoCir-CSIC), Madrid, Spain; and Interdisciplinary Platform Horizonte Verde (CSIC), Madrid, Spain., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Bioethanol lignin-rich residue from olive stones for electrospun nanostructures development and castor oil structuring

  • Rubio-Valle, José F.
  • Martín-Alfonso, José Enrique
  • Eugenio, María E.
  • Ibarra, David
  • Oliva, José Miguel
  • Manzanares, Paloma
  • Valencia, Concepción
13 Pág., This work describes the chemical and structural characterization of a lignin-rich residue from the bioethanol production of olive stones and its use for nanostructures development by electrospinning and castor oil structuring. The olive stones were treated by sequential acid/steam explosion pretreatment, further pre-saccharification using a hydrolytic enzyme, and simultaneous saccharification and fermentation (PSSF). The chemical composition of olive stone lignin-rich residue (OSL) was evaluated by standard analytical methods, showing a high lignin content (81.3 %). Moreover, the structural properties were determined by Fourier-transform infrared spectroscopy, nuclear magnetic resonance, and size exclusion chromatography. OSL showed a predominance of β-β' resinol, followed by β-O-4' alkyl aryl ethers and β-5' phenylcoumaran substructures, high molecular weight, and low S/G ratio. Subsequently, electrospun nanostructures were obtained from solutions containing 20 wt% OSL and cellulose triacetate with variable weight ratios in N, N-Dimethylformamide/Acetone blends and characterized by scanning electron microscopy. Their morphologies were highly dependent on the rheological properties of polymeric solutions. Gel-like dispersions can be obtained by dispersing the electrospun OSL/CT bead nanofibers and uniform nanofiber mats in castor oil. The rheological properties were influenced by the membrane concentration and the OSL:CT weight ratio, as well as the morphology of the electrospun nanostructures., This work is a collaborative research of different projects: RTI2018-096080-B-C21 , RTI2018-096080-B-C22 , PID2021-125637OB-I00 , TED2021-132122B-C21 and ENE2017-85819-C2-2-R funded by MCIN /AEI/10.13039/501100011033 and by “ERDF A way of making Europe”, SUSTEC-CM S2018/EMT-4348 project funded by Comunidad de Madrid . The authors gratefully acknowledge the aforementioned financial support. J.F.R.-V. additionally has received a Ph.D. Research Grant PRE2019-090632 from Spain's Ministry of Science and Innovation . The financial support is gratefully acknowledged., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

The use of kraft lignin to enhance nanocellulose film properties

  • Martín-Sampedro, Raquel
  • Ovejero-Pérez, Antonio
  • Oliet, Mercedes
  • Alonso, Virginia
  • Rodríguez, Francisco
  • Ibarra, David
  • Eugenio, María E.
Artículo presentado en el Congreso Faraday Discussion on "Frontiers in physical chemistry for lignin valorisation" celebrado en Londres del 10 al 12 de septiembre de 2025, organizado por la Royal Society of Chemistry (RSC)., The urgent need to replace petroleum-based plastics with renewable and biodegradable alternatives has driven interest in biopolymers from lignocellulosic biomass as sustainable solutions. Among these, nanocellulose stands out as a versatile product capable of forming strong, transparent, and flexible films. However, these films lack active properties like antioxidant capacity and UV-shielding, essential for applications such as food packaging. To address this, incorporating lignin, a byproduct of lignocellulosic biorefineries and pulp industries, offers a promising route to enhance the functionality of nanocellulose films. This study aimed to enhance the properties of nanocellulose films by incorporating isolated kraft lignin. Nanocellulose (TOCNF) was produced from Eucalyptus globulus bleached kraft pulp using TEMPO-mediated oxidation followed by microfluidization. Kraft lignin was isolated from black liquor via acid precipitation. Two protocols for adding lignin to the TOCNF suspension were evaluated: one involved mixing TOCNF (0.3%) with a 0.3% aqueous lignin suspension, while the other used lignin diluted in an acetone:water (9:1) solution to form lignin nanoparticles (LNP) through solvent shift while mixing with the aqueous TOCNF suspension also at the 0.3% concentration. Films were prepared with lignin concentrations of 2.5%, 5%, 10%, and 20% for each protocol. The films were characterized using FTIR spectroscopy and SEM microscopy. Moreover, their antioxidant and antimicrobial capacities as well as their water vapor permeability (WVP) were assessed. Incorporating lignin into the TOCNF suspension enhanced the barrier properties of the films, particularly when lignin was introduced as LNP, achieving a WVP reduction from 1.6·10⁻¹¹ gm⁻¹s⁻¹Pa⁻¹ for pure TOCNF to 1.3–0.9·10⁻¹¹ gm⁻¹s⁻¹Pa⁻¹ for TOCNF with LNP. However, adding bulk lignin at a high concentration (20%) negatively affected WVP, increasing it to 2.0·10⁻¹¹ gm⁻¹s⁻¹Pa⁻¹. Antioxidant capacity correlated with lignin content, showing greater enhancement when lignin was present as nanoparticles (34.7 mg Trolox equivalent/g film at 20% LNP) compared to bulk lignin (26.4 mg Trolox equivalent/g film at 20%). Regarding antimicrobial capacity, the same tendency was observed, showing a LogR of 4.99 when bulk lignin was used at 20% compared to LogR 7.94 when LNP was employed at 20%, both against Staphylococcus aureus.These results indicate that forming LNP in situ within the TOCNF suspension is a more effective approach to optimize the properties of nanocellulose films., The pressing need to replace petroleum-based plastics with renewable and biodegradable alternatives has sparked growing interest in biopolymers derived from lignocellulosic biomass as sustainable solutions. Among these, nanocellulose stands out as a versatile product capable of forming strong, transparent, and flexible films. However, these films lack active properties like antioxidant, antibacterial and UV-shielding capacity, essential for applications such as food packaging. To address this, incorporating lignin, a byproduct of lignocellulosic biorefineries, offers a promising route to enhance the functionality of nanocellulose films. In line with this idea, this work studies the incorporation of kraft lignin into nanocellulose films by two different protocols: the first protocol involves directly mixing a cellulose nanofiber (CNF) suspension with an aqueous lignin suspension; the second protocol uses lignin dissolved in acetone : water (9 : 1) which is transformed into lignin nanoparticles (LNPs) via solvent shifting when mixed with the aqueous CNF suspension. The resulting suspensions of CNFs and lignin were subsequently used to produce casting films. It was found that incorporating lignin into the CNF film not only conferred UV-shielding capacity, but also enhanced barrier properties without compromising the mechanical properties, particularly when lignin was introduced as LNPs (even at 10–20% LNP content). However, adding bulk lignin at a high concentration (20%) negatively affected water vapor permeability and mechanical properties. Antioxidant and antibacterial capacities correlated with lignin content, showing greater enhancement when lignin was present as nanoparticles compared to bulk lignin. These results indicate that forming LNPs in situ within the CNF suspension is a more effective approach to optimize the properties of nanocellulose films. Thus, the obtained films presented good active properties with mechanical properties comparable to those of traditional plastics, but significantly lower barrier properties., This work was supported by the MICIN/AEI/10.13039/501100011033 (Spain) and “ERDF A way of making Europe” [PID2022-141965OB-C21]; the MCIN/AEI/10.13039/501100011033 and the “European Union Next Generation EU/PRTR” [TED 2021-132122B-C21]; and the Comunidad de Madrid (Spain) [SUSTEC-CM S2018/EMT-4348 and TEC2024-BIO-27]. The authors are also grateful for the support of the following Interdisciplinary Platforms: Sustainable Plastics towards a Circular Economy (SusPlast-CSIC), Sustainability and Circular Economy (SosEcoCir-CSIC) and Horizonte Verde (CSIC)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Insights into structure and bioactive potential of solvent-extracted lignins from enzymatic hydrolysis residues

  • Eugenio, María E.
  • García-Fuentevilla, Luisa
  • Chamizo, Lucía
  • Martín-Sampedro, Raquel
  • Santos, José I.
  • Ibarra, David
To enhance the competitiveness of biorefineries based on sugars production, the interest in the valorization of hydrolysis lignin residue is becoming increasingly essential. Nevertheless, hydrolysis lignin residue (Hyd-Lig) faces limitations in its valorization—for instance, as bioactive agent due to different factors, including poor solubility, carbohydrates contamination, and chemical and structural variability. In this study, alkaline and organosolv (acetone, dioxane or methanol) approaches were evaluated for extraction of lignin from a hydrolysis residue generated during steam explosion and subsequent saccharification of poplar. The extracted lignins were characterized according to purity, chemical, and structural features by analytical standard methods and FTIR, SEC, 13C and 1H–13C NMR. Antioxidant (Trolox Equivalent Antioxidant Capacity, TEAC) and antibacterial (against Staphylococcus aureus) properties were also evaluated. The extracted lignin recovery yield using alkaline conditions (Alk-Lig) was 39.1 %, whereas using acetone (Ace-Lig), dioxane (Dio-Lig), and methanol (Met-Lig) were 24.1 %, 19.1 % and 13.1 %, respectively. Compared to Hyd-Lig, with a total lignin content of 63.9 %, extracted lignins displayed a higher purity (total lignin of 93.9–95.9 %). In addition, extracted lignins displayed a removal of lateral chains (aryl-β ether) and, therefore presented a higher phenolic content (around of 210–238 mg GAE/g lignin) compared to Hyd-Lig sample (42 mg GAE/g lignin). Then, the solubility of extracted lignins was improved, and higher antioxidant (TEAC values between 0.055 and 0.155) and antibacterial activities (Log R values between 0.5 and 1.2), compared to Hyd-Lig sample (TEAC and Log R of 0.022 and 0.02, respectively), were obtained. This work shows the necessity of extracting lignin from hydrolysis residues to enhance its applicability as bioactive agent and enable its potential valorization., The authors wish to thank the project TED 2021–132122B-C21 funded by MCIN/AEI/10.13039/501100011033 and by the “European Union Next Generation EU/PRTR” and the project PID2022–141965OB-C21 funded by MCIN/AEI/10.13039/501100011033 and by “ERDF A way of making Europe” to support this study. AgroSUSTEC-CM (TEC-2024/BIO-27) project, funded by Comunidad de Madrid, is also grateful. Authors are also grateful for the support of the Interdisciplinary Platform for Sustainable Plastics towards a Circular Economy (SusPlast-CSIC), Madrid, Spain; Interdisciplinary Platform for Sustainability and Circular Economy (SosEcoCir-CSIC), Madrid, Spain; Interdisciplinary Platform Horizonte Verde (CSIC), Madrid, Spain; and RED LIGNOCEL (RED2024–153800-T) funded by MICIU/AEI/10.13039/501100011033. The contribution of COST Action LignoCOST (CA17128), supported by COST (European Cooperation in Science and Technology), in promoting interaction, exchange of knowledge and collaborations in the field of lignin valorization is also gratefully acknowledged., Peer reviewed