Pasar al contenido principal

PRODUCCION DE NANOFIBRAS DE LIGNINA POR ELECTROESPINNING PARA SU INCORPORACION COMO INGREDIENTE MULTIFUNCIONAL EN NUEVAS FORMULACIONES DE GRASAS LUBRICANTES BIODEGRADABLES

RTI2018-096080-B-C21

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Convocatoria Proyectos I+D+i Retos de Investigación
Año convocatoria 2018
Plan Estatal 2017-2020 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario UNIVERSIDAD DE HUELVA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 8
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Lignin-enriched residues from bioethanol production: Chemical characterization, isocyanate functionalization and oil structuring properties

  • Borrero-López, Antonio M.
  • Valencia, Concepción
  • Ibarra, David
  • Ballesteros, Ignacio
  • Franco, José Mariano
12 Pág., Lignin-enriched waste products from bioethanol production of agriculture residues were tested as structuring agents in castor oil once functionalized with hexamethylene diisocyanate. Cane bagasse, barley and wheat straw were processed through steam explosion, pre-saccharification and simultaneous saccharification and fermentation (PSSF). Alternatively, cane bagasse was submitted to steam explosion and enzymatic hydrolysis (EH). Several Nuclear Magnetic Resonance techniques were used to characterize both residues and NCO-functionalized counterparts. The β-O-4'/resinol/phenylcoumaran content and hydroxyphenyl/guaiacyl/syringyl distribution depend on biomass source, pretreatment, and enzymatic hydrolysis. Total hydroxyl content (from 1.23 for cane bagasse to 1.85 for wheat straw residues), aromatic/aliphatic hydroxyl ratio (0.78 for cane bagasse and 0.61 and 0.49 for barley and wheat straw residues, respectively) and S/G ratio (ranging from 0.25 to 0.86) influence the NCO-functionalization and oleogel rheological response. Oleogels obtained with barley straw residues exhibited the highest values of the storage modulus; around 2 × 105 Pa and 104 Pa for 25% and 20% contents, respectively. PSSF process showed weaker modification, leading to softer viscoelastic response compared to EH. These oleogels exhibited rheological properties similar to lubricating greases of different NLGI grades. Therefore, we herein show an integrative protocol for the valorization of lignin-enriched residues from bioethanol production as potential thickeners of lubricating greases., This work is part of two coordinated research projects (RTI2018-096080-B-C21 and RTI2018-096080-B-C22) funded by MCIN/AEI/10.13039/501100011033 and by “ERDF A way of making Europe”. The financial support is gratefully acknowledged. A.M.B-L. also acknowledges the Ph.D. Research Grant FPU16/03697 from MECD (Spain)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

A sustainable methanol-based solvent exchange method to produce nanocellulose-based ecofriendly lubricants

  • Roman, Claudia
  • García-Morales, Moisés
  • Eugenio, María E.
  • Ibarra, David
  • Martín-Sampedro, Raquel
  • Delgado, Miguel A.
10 Pág.  Centro de Investigación Forestal (CIFOR)., A prospective methodology aimed to develop totally sustainable oleogels with potential application in lubrication is reported. Oleogels were prepared with cellulose nanofibrils from elm pulps in castor oil. Even at a concentration as low as 1.4 wt%, the oleogels showed rheological behaviors similar to a traditional lithium grease used as reference. In that sense, the high thickening power of cellulose nanofibers was remarked. Never-dried bleached and unbleached elm pulps were mechanically treated with PFI mill refiner and microfluidizer. Moreover, as an alternative way of producing cellulose nanofibrils, the never-dried bleached elm pulp was chemically oxidized using 2,2,6,6-tetramethylpiperidine-1-oxyl radical (TEMPO). The three types of nanofibers were characterized and used in the production of oleogels. The great challenge was to remove the high amount of water retained by the nanofibrils during the nanofibrillation treatment before it was incorporated into the vegetable oil-based lubricant. Alternative strategies such as liophilization or drying failed because the nanofibers, with very high specific surface and strong capacity to interact among them by hydrogen bonding, underwent severe aggregation. Instead, the proposed methanol-based solvent exchange method enabled the transfer of the cellulose nanofibrils from the origin hydrogel to the vegetable oil with no detriment of both their aspect ratio and thickening capacity. Chemical considerations are provided with regard to such a solvent-mediated method, which yielded homogeneous and storage-stable oleogels. This work may attract the interest of lubricant manufacturers to produce nanocellulose-based eco-lubricating greases for industrial applications., This work is part of a Research Project sponsored by “Programa Operativo FEDER-Andalucía 2014–2020” (UHU-1255843). Also, part of this investigation is included in the Research Projects “RTI2018-096080-B-C21” and RTI2018-096080-B-C22 supported by the MCIU/AEI/ FEDER/UE, and SUSTEC-CM S2018/EMT-4348 by Comunidad de Madrid. Funding for open access charge: Universidad de Huelva/CBUA., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Different Kraft lignin sources for electrospun nanostructures production: Influence of chemical structure and composition

  • García-Fuentevilla, Luisa
  • Rubio-Valle, José F.
  • Martín-Sampedro, Raquel
  • Valencia, Concepción
  • Eugenio, María E.
  • Ibarra, David
14Pág., This work focuses on the structural features and physicochemical properties of different Kraft lignins and how they can influence the electrospinning process to obtain nanostructures. Structural features of Kraft lignins were characterized by nuclear magnetic resonance, size exclusion chromatography, fourier-transform infrared spectroscopy, and thermal analysis, whereas chemical composition was analyzed by standard method. The addition of cellulose acetate (CA) improves the electrospinning process of Kraft lignins (KL). Thus, solutions of KL/CA at 30 wt% with a KL:CA weight ratio of 70:30 were prepared and then physicochemical and rheologically characterized. The morphology of electrospun nanostructures depends on the intrinsic properties of the solutions and the chemical structure and composition of Kraft lignins. Then, surface tension, electrical conductivity and viscosity of eucalypt/CA and poplar/CA solutions were suitable to obtain electrospun nanostructures based on uniform cross-linked nanofibers with a few beaded fibers. It could be related with the higher purity and higher linear structure, phenolic content and S/G ratios of lignin samples. However, the higher values of electrical conductivity and viscosity of OTP/CA solutions resulted in electrospun nanostructure with micro-sized particles connected by thin fibers, due to a lower purity, S/G ratio and phenolic content and higher branched structure in OTP lignin., This work is part of two coordinated research projects (RTI2018-096080-B-C21 and RTI2018-096080-B-C22) funded by MCIN/AEI/ 10.13039/501100011033 and by “ERDF A way of making Europe”. The authors also wish to thank the Comunidad de Madrid and MCIU/AEI/FEDER, EU for funding this study via Projects SUSTEC-CM S2018/EMT-4348. The authors also acknowledge the pre-doctoral grants from José Fernando Rubio Valle (Ref. PRE2019-090632). The contribution of COST Action LignoCOST (CA17128), supported by COST (European Cooperation in Science and Technology), in promoting interaction, exchange of knowledge and collaborations in the field of lignin valorization is gratefully acknowledged., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Cellulose Pulp- and Castor Oil-Based Polyurethanes for Lubricating Applications: Influence of Streptomyces Action on Barley and Wheat Straws

  • Borrero-López, Antonio M.
  • Valencia, Concepción
  • Blánquez, Alba
  • Hernández, Manuel
  • Eugenio, María E.
  • Franco, José Mariano
15 Pág., The replacement of mineral oils and non-renewable gelling agents is an imperative requirement for the lubricant industry in the near future. In this framework, cellulose pulp and castor oil are proposed as sustainable substitutes for these components. Biological treatment has been explored and evaluated to enhance the dispersing and thickening properties of cellulose pulp in oil media. Streptomyces sp. MDG147 and MDG301 strains were employed to modify agricultural wheat and barley straw residues from which cellulose pulp was obtained afterwards. In addition, an environmentally friendly process for the production of cellulose-pulp-/castor-oil-based polyurethanes was applied, in which neither catalysts nor harmful solvents were used, resulting in chemical oleogels. These oleogels were rheologically and tribologically characterized to evaluate their performance as lubricating greases. The enzymatic activity pattern developed was dependent on the raw material, the strain type, and the temperature, influencing the cellulose pulp's composition, polymerization degree, and crystallinity. These modified characteristics tuned the rheological behavior of the different oleogels, providing a beneficial range of viscoelastic responses and viscosity values that were generally favored by the Streptomyces action. Furthermore, the friction coefficient and dimensions of wear scars measured in a tribological contact were comparable to, or even lower than, those found with commercial and other bio-based lubricating greases that have previously been studied., This work is part of two coordinated research projects (RTI2018-096080-B-C21 and RTI2018-096080-B-C22) sponsored by MICIU-FEDER. A.M.B.-L. has received a Ph.D. Research Grant from the Ministerio de Educación, Cultura y Deporte (FPU16/03697). We gratefully acknowledge the financial support, Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Kraft lignins from different poplar genotypes obtained by selective acid precipitation and their use for the production of electrospun nanostructures

  • Ibarra, David
  • García-Fuentevilla, Luisa
  • Rubio-Valle, José F.
  • Martín-Sampedro, Raquel
  • Valencia, Concepción
  • Eugenio, María E.
13 Pág., Kraft lignins from different poplar genotypes (Populus alba L. “PO-10-10-20” and Populus x canadensis “Ballotino”) were isolated by selective acid precipitation (pH 5 and 2.5), chemically and structurally characterized and used together with cellulose acetate (CA) for the manufacture of nanostructures by electrospinning. Generally, lignins showed a predominance of β-β´ resinols substructures (4.7–5.3 linkages per 100 aromatic units) followed by β-O-4´ (1.6–3.3 linkages per 100 aromatic units) and β-5´ phenylcoumarans (0.5–2.4 linkages per 100 aromatic units) and a high abundance of S lignin units (S/G 3.0–4.3). Moreover, lignins showed low molecular weight values (between 5.14 and 5.59 KDa) and high phenolic content (529.1 –644.5 mg GAE/g lignin). Regarding the electrospun nanostructures obtained from Kraft lignins/CA solutions, all of them presented uniform cross-linked nanofibers with a few beaded fibers according to the suitable range values of surface tension (29.18–29.71 mN/cm), electrical conductivity (131.2–158.9 μS/cm) and dynamic viscosity (0.28–0.32 Pa.s) that biopolymer solutions showed. Nevertheless, electrospun Kraft lignins/CA nanostructures with larger mean diameters were generated from lignins at pH 5, which displayed higher phenolic and β-O-4´ contents compared to lignins at pH 2.5. On the other hand, the type of poplar lignin genotype did not exert a significant influence on the mean fiber diameter., This work is part of two coordinated research projects (RTI2018-096080-B-C21 and RTI2018-096080-B-C22) funded by MCIN/AEI/10.13039/501100011033 and by “ERDF A way of making Europe”. The authors also wish to thank the Comunidad de Madrid and MCIN/AEI/FEDER, EU for funding this study via Projects SUSTEC-CM S2018/EMT-4348 and TED2021-132122B-C21, respectively. The authors also acknowledge the pre-doctoral grants from José Fernando Rubio Valle (Ref. PRE2019-090632)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Evaluation of lignin-enriched side-streams from different biomass conversion processes as thickeners in bio-lubricant formulations

  • Borrero-López, Antonio M.
  • Martín-Sampedro, Raquel
  • Ibarra, David
  • Valencia, Concepción
  • Eugenio, María E.
  • Franco, José Mariano
16 Pág., This study explores the suitability of residual lignin-containing fractions generated as side-streams in different conversion processes of eucalypt and pine woods as thickening agents in bio-lubricant formulations. These conversion processes included fermentable sugars extraction by autohydrolysis or steam explosion and kraft pulping. Structural properties of lignin fractions were characterized by FTIR, 1H and 13C NMR, two-dimensional NMR, TGA and SEC, whereas their compositions were analysed by standard analytical methods. On the other hand, chemical oleogels were prepared with NCO-functionalized residual lignin fractions, and characterized by means of rheological, tribological and AFM techniques. Hydrolysis lignin fractions exhibited a great content of carbohydrates, especially glucose (46.0-48.5%), xylose (4.3-15.6%) and lignin (32.5-39.9%) with a well-maintained structure, displaying the main inter-unit linkages and low phenolic content. By contrast, kraft lignin fractions presented a lower carbohydrate content, mainly xylose (3.4-4.3%), and higher content (44.9-67%) of severely degraded lignin, showing a dramatic reduction of inter-unit linkages, and thereby high phenolic content. The rheological response of NCO-functionalized lignin fractions-based oleogels is highly influenced by the composition and chemical structure of residual lignin fractions. Moreover, these oleogels presented suitable tribological properties with values of the friction coefficient lower than those typically exhibited by standard lubricating greases., This work is part of two coordinated research projects ( RTI2018-096080-B-C21 and RTI2018-096080-B-C22 ) sponsored by MICIU - FEDER and another sponsored by the Comunidad de Madrid ( SUSTEC-CM S2018/EMT-4348 ). One of the authors, A.M.B.-L., has received a Ph.D. Research Grant from the Ministerio de Educación, Cultura y Deporte ( FPU16/03697 ). We gratefully acknowledge their financial support., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Bioethanol lignin-rich residue from olive stones for electrospun nanostructures development and castor oil structuring

  • Rubio-Valle, José F.
  • Martín-Alfonso, José Enrique
  • Eugenio, María E.
  • Ibarra, David
  • Oliva, José Miguel
  • Manzanares, Paloma
  • Valencia, Concepción
13 Pág., This work describes the chemical and structural characterization of a lignin-rich residue from the bioethanol production of olive stones and its use for nanostructures development by electrospinning and castor oil structuring. The olive stones were treated by sequential acid/steam explosion pretreatment, further pre-saccharification using a hydrolytic enzyme, and simultaneous saccharification and fermentation (PSSF). The chemical composition of olive stone lignin-rich residue (OSL) was evaluated by standard analytical methods, showing a high lignin content (81.3 %). Moreover, the structural properties were determined by Fourier-transform infrared spectroscopy, nuclear magnetic resonance, and size exclusion chromatography. OSL showed a predominance of β-β' resinol, followed by β-O-4' alkyl aryl ethers and β-5' phenylcoumaran substructures, high molecular weight, and low S/G ratio. Subsequently, electrospun nanostructures were obtained from solutions containing 20 wt% OSL and cellulose triacetate with variable weight ratios in N, N-Dimethylformamide/Acetone blends and characterized by scanning electron microscopy. Their morphologies were highly dependent on the rheological properties of polymeric solutions. Gel-like dispersions can be obtained by dispersing the electrospun OSL/CT bead nanofibers and uniform nanofiber mats in castor oil. The rheological properties were influenced by the membrane concentration and the OSL:CT weight ratio, as well as the morphology of the electrospun nanostructures., This work is a collaborative research of different projects: RTI2018-096080-B-C21 , RTI2018-096080-B-C22 , PID2021-125637OB-I00 , TED2021-132122B-C21 and ENE2017-85819-C2-2-R funded by MCIN /AEI/10.13039/501100011033 and by “ERDF A way of making Europe”, SUSTEC-CM S2018/EMT-4348 project funded by Comunidad de Madrid . The authors gratefully acknowledge the aforementioned financial support. J.F.R.-V. additionally has received a Ph.D. Research Grant PRE2019-090632 from Spain's Ministry of Science and Innovation . The financial support is gratefully acknowledged., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Assessment of Lignin Residues from Bioethanol Production of Olive Stones as Green Chemical Thickener of Epoxidized Linseed Oil

  • Cortés-Triviño, Esperanza
  • Valencia, Concepción
  • Franco, José Mariano
  • Oliva, José Miguel
  • Manzanares, Paloma
  • Eugenio, María E.
  • Ibarra, David
18 Pág., This work focused on the characterization of lignin residues from bioethanol production of olive stones (OS) and the use of these residues to chemically thicken epoxidized linseed oil (ELO). OS were processed by an acid/steam explosion pretreatment, followed by pre-saccharification, using different enzyme dosages, and simultaneous saccharification and fermentation. The chemical composition of the OS lignin residues was analysed, revealing a high lignin content (66.6–69.5%), and lower quantities of glucan (17.4–19.3%) and xylan (2.8–2.9%). Whereas, the structural properties of OS lignin residues were characterized by Fourier-transform infrared (FTIR) spectroscopy, nuclear magnetic resonance (NMR), thermogravimetric analysis and size exclusion chromatography (SEC). OS lignin residues displayed the main inter-unit linkages (β–β′ resinol (51.0–59.0%), followed by β-O-4′ alkyl aryl ethers (27.0–35.2%) and β-5′ phenylcoumaran (11.4–13.2%) substructures), high molecular weights (22,000–25900 Da), low S/G ratios (1.2–1.5) and phenolic groups content (48–55 mg GAE/g lignin). Moreover, OS lignin residues were dispersed in ELO to obtain thickened formulations, which were characterized by FTIR and NMR. Oil thickening was achieved by promoting the chemical crosslinking between lignocellulose hydroxyl groups and ELO epoxy groups, enabling the compatibilization of both components. Up to tenfold viscosity increment of the resulting thickened formulations in relation to ELO’s viscosity was observed. Besides, thickened formulations exhibited viscoelastic properties, evincing oil structuration to some extent. Graphical Abstract: (Figure presented.), Open Access funding provided thanks to the CRUE-CSIC agreement with Springer Nature. This work is collaborative research which is part of different projects: coordinated research projects (RTI2018-096080-B-C21 and RTI2018-096080-B-C22) and project PID2022-141965OB-C21 funded by MCIN/AEI/https://doi.org/10.13039/501100011033 and by “ERDF A way of making Europe”, TED 2021-132122B-C1 funded by MCIN/AEI/https://doi.org/10.13039/501100011033 and by the “European UnionNextGenerationEU/PRTR”, ENE2017-85819-C2-2-R funded by MINECO, and SUSTEC-CM S2018/EMT-4348 project funded by Comunidad de Madrid. The authors gratefully acknowledge the aforementioned financial support., Peer reviewed