Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 10
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

High speed processing of NiFe2O4 spinel using a laser furnace

  • Özçelik, Bekir
  • Özçelik, S.
  • Amaveda, H.
  • Santos, H.
  • Borrel, C. J.
  • Sáez-Puche, R.
  • Fuente, Germán F. de la
  • Angurel, Luis A.
The Laser Furnace (LF) method has been applied to directionally solidify NiFe2O4 spinel disks from a mixture of Fe and Ni oxides in order to obtain uniform, dense targets for controlled synthesis of spinel nanoparticles via Laser Ablation. Application of a CO2 laser in Line Scan mode onto a sample with the desired stoichiometry, enabled melt processing above 1580 °C at its outer surface layer. This process was carried out inside a continuous roller furnace at a maximum volume temperature of 1000 °C. Such combination helps avoid excessive thermal stress, crack formation and catastrophic failure of these magnetic ceramic monoliths. Higher energy incubation values yield increased molten volumes and a thicker resolidified surface layer with a dense microstructure. Despite the high solidification rates imposed, NiFe2O4 spinel is the main phase obtained according to X-Ray Diffraction (XRD) and magnetization studies. LF processed samples exhibit a reduction of the coercive fields and an increase of the saturation magnetization values, evidence for soft ferromagnetism and characteristic of the magnetic behaviour associated with this spinel. This work demonstrates the convenience of the LF method for preparation of uniform, dense targets for Laser Ablation and other evaporation based techniques used in the fabrication of nanoparticles., The authors acknowledge financial support from MINECO-AEI-FEDER, EU (projects MAT2016-79866-R and ENE2017-83669-C4-1-R) and SPRINT (EU H2020-FET-OPEN/0426) projects and from Gobierno de Aragón “Construyendo Europa desde Aragón” (research group T54_17R)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Laser-induced scanning transfer deposition of silver electrodes on glass surfaces: A green and scalable technology

  • Molina Mansilla, Ricardo
  • Ertuğrul, M.
  • Navarro, Rafael
  • Rico, Víctor J.
  • Yubero, Francisco
  • González-Elipe, Agustín R.
  • Fuente, Germán F. de la
  • Angurel, Luis A.
A pulsed laser ablation backwriting technique with high repetitive rates is implemented for the fabrication of silver coatings on glass surfaces. This method enables geometrical constraint-free deposition of metallic coatings. These exhibit sufficiently low electrical resistance to be used as electrodes in dielectric barrier discharge (DBD) plasma elements. Ambient air deposition of metallic silver electrodes on standard glass slides is explored using a sub-ns UV laser source, combined with hybrid beam scanning methods. The green nature of the overall deposition process includes a preliminary irradiation scan to homogenise the target surface before the subsequent backwriting step. Metal transfer is achieved by combining two phenomena within a simple beam scanning process: LIRT (laserinduced reverse transfer) of silver from the target to the glass, with a partial and secondary LIFT (Laser-Induced Forward Transfer) of silver from the glass to the target. Appropriate selection of pulse energy and pulse repetition rates, beam scanning velocities and target motion enable the growth of sufficiently thick Ag deposits on glass with the required low electrical resistivity and nearly 2D constraint-free geometry. This method avoids the use of vacuum and liquids, resulting in a cheap, facile and green methodology for the deposition of silver electrodes onto transparent substrate surfaces., This paper is dedicated to the memory of Prof. Rafael Navarro. The authors gratefully acknowledge the financial support from Spanish MINECO-AEI and EU FEDER Program (projects ENE2017-83669-C4-1-R and MAT2016-79866-R), from EU project SPRINT (H2020-FETOPEN 801464) and from the Gobierno de Aragón “Construyendo Europa desde Aragón” (research group T54_20R). Authors also would like to acknowledge the use of Servicio General de Apoyo a la Investigación-SAI and the National Facility ELECMI ICTS, node “Laboratorio de Microscopías Avanzadas” at University of Zaragoza., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Synthesis of 2D Porous Crystalline Materials in Simulated Microgravity

  • Contreras-Pereda, Noemí
  • Rodríguez-San Miguel, David
  • Franco, Carlos
  • Sevim, Semih
  • Vale, João Pedro
  • Solano, Eduardo
  • Fong, Wye-Khay
  • Del Giudice, Alessandra
  • Galantini, Luciano
  • Pfattner, Raphael
  • Pané, Salvador
  • Sotto Mayor, Tiago
  • Ruiz Molina, Daniel
  • Puigmartí Luis, Josep
To date, crystallization studies conducted in space laboratories, which are prohibitively costly and unsuitable to most research laboratories, have shown the valuable effects of microgravity during crystal growth and morphogenesis. Herein, an easy and highly efficient method is shown to achieve space-like experimentation conditions on Earth employing custom-made microfluidic devices to fabricate 2D porous crystalline molecular frameworks. It is confirmed that experimentation under these simulated microgravity conditions has unprecedented effects on the orientation, compactness and crack-free generation of 2D porous crystalline molecular frameworks as well as in their integration and crystal morphogenesis. It is believed that this work will provide a new “playground” to chemists, physicists, and materials scientists that desire to process unprecedented 2D functional materials and devices., N.C.-P., D.R.-S.-M., C.F. contributed equally to this work. This work was supported by the European Research Council Starting Grant microCrysFact (ERC-2015-STG No. 677020), the Horizon 2020 FETOPEN project SPRINT (No. 801464), the Swiss National Science Foundation (project no. 200021_181988), grant MAT 2015-70615-R from the Spanish Government funds and by the European Regional Development Fund (ERDF). The ICN2 is funded by the CERCA programme/Generalitat de Catalunya. The ICN2 is supported by the Severo Ochoa Centres of Excellence programme, funded by the Spanish Research Agency (AEI, grant no. SEV-2017-0706). N.C.-P. acknowledges support from “laCaixa” Foundation (fellowship ID 100010434). The fellowship code is LCF/BQ/ES17/11600012. N.C.-P. also acknowledges the financial support of COST action MP1407. R.P. acknowledges support from the Marie Curie Cofund, Beatriu de Pinós Fellowship AGAUR 2017 BP 00064. The GIWAXS experiments were conducted on the NCD-SWEET beamline of the ALBA synchrotron, Spain and on the SAXS/WAXS beamline of the Australian Synchrotron, ANSTO, Australia. GIWAXS experiments of Ni3(HITP)2 and COF-TAPB-BTCA were performed at the NCD-SWEET beamline at ALBA Synchrotron with the collaboration of ALBA staff. The authors acknowledge the support of the ANSTO, in providing the facilities for the GIWAXS experiments used for the characterization of COF-TAPB-BTCA in this work., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Structure, magnetic, photocatalytic and blood compatibility studies of nickel nanoferrites prepared by laser ablation technique in distilled water

  • Özçelik, Sezen
  • Yalçın, B.
  • Arda, L.
  • Santos, H.
  • Sáez-Puche, R.
  • Angurel, Luis A.
  • Fuente, Germán F. de la
  • Özçelik, Bekir
The main objective of this study is to investigate the structural features, magnetic behaviour, photocatalytic properties and blood compatibility of NiFe2O4 nanoparticles (NPs) obtained by subnanosecond laser ablation in water. Structure and size distribution of NPs were studied using X-Ray Diffractometry (XRD) and Transmission Electron Microscopy (TEM). The photocatalytic properties of NPs were evaluated by photo-degradation of Methylene Blue (MeB) dye under ambient visible light illumination. Four different kinetic models were used to identify the photocatalytic degradation mechanism of NiFe2O4 nanoparticles and it was found that the pseudo-second-order model was the most suitable type to interpret the experimental kinetic data of MeB photodegradation. The hemocompatibility of NiFe2O4 nanoparticles was studied by hemolysis tests using human erythrocytes drawn from healthy volunteers. NiFe2O4 nanoparticles caused undesirable hemolysis ratios at 0.05, 1 and 5 mg/ml concentrations, while the biologically safe concentration of these nanoparticles was found to be below 0.01 mg/ml., The authors acknowledge financial support from Spanish MINECO-AEI-FEDER EU (project ENE2017-83669-C4-1-R) and SPRINT (EU H2020-FET-OPEN/0426) projects and from Gobierno de Aragón “Construyendo Europa desde Aragón” (research group T54_20R)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Generating colours through a novel approach based on spatial ALD and laser processing

  • Frechilla, Alejandro
  • Sekkat, A.
  • Dibenedetto, M.
  • Presti, Francesca lo
  • Porta-Velilla, Luis
  • Martínez Fernández, Elena
  • Fuente, Germán F. de la
  • Angurel, Luis A.
  • Muñoz-Rojas, David
This work studies the combination of direct femtosecond laser structuring of metal surfaces and Spatial Atomic Layer Deposition (SALD) of metal oxides as a novel approach to generate colours on different types of day-to-day metallic objects. In particular, a stainless-steel knife and an outdated 25 ct Dutch florin coin have been selected for the study. Our results show that it is possible both, to preserve the iridescence properties produced by laser processing and to tune the final metal surface colour by controlling the thickness of the ZnO coating. At the same time, this oxide coating could act as a protecting layer for the original material. We thus explore two different strategies to generate colour, namely, iridescence and interference, which can be even developed selectively. This novel methodology to colour metallic surfaces is a promising route to achieve cheap, scalable, and high-throughput processing methods and opens up a new avenue of possibilities and applications related to colour., The authors gratefully acknowledge the financial support from EU project SPRINT (H2020-FETOPEN 801464), Spanish MCIN/AEI/10.13039/501100011033 (project PID2020-113034RB-I00) and from the Gobierno de Aragón (research group T54_23R). Authors also would like to acknowledge the use of Servicio General de Apoyo a la Investigación-SAI and Laboratorio de Microscopías Avanzadas at University of Zaragoza. A. Frechilla and L. Porta-Velilla acknowledge support of the Gobierno de Aragón through their predoctoral contract. DMR and FLP acknowledge support from the Ministère de l’Europe et des Affaires étrangères (MEAE) the Ministère de l’Enseignement Supérieur et de la Recherche (MESR) and the Ministero dell’Istruzione, dell’Università e della Ricerca (MIUR) through a PhC Galilée/Galileo project., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Laser annealing of transparent ZnO thin films: a route to improve electrical conductivity and oxygen sensing capabilities

  • Frechilla, Alejandro
  • Frechilla, Javier
  • Angurel, Luis A.
  • Toldra-Reig, Fidel
  • Balas, Francisco
  • Martínez Fernández, Elena
  • Fuente, Germán F. de la
  • Muñoz-Rojas, David
The chemical deposition of high-performance zinc oxide (ZnO) thin films is challenging, thus significant efforts have been devoted during the past decades to develop cost-effective, scalable fabrication methods in gas phase. This work demonstrates how ultra-short-pulse laser beam scanning (LBS) can be used to modulate electrical conductivity in ZnO thin films deposited on soda–lime glass by spatial atomic layer deposition (SALD), a high-throughput, low-temperature deposition technique suitable for large-area applications. By systematically optimizing laser parameters, including pulse energy and hatching distance, significant improvements in the electrical performance of 90 nm-thick ZnO films were achieved. The optimization of the laser annealing parameters – 0.21 μJ per pulse energy and a 1 μm hatching distance—yielded ZnO films with an electrical resistivity of (9 ± 2) × 10−2 Ω cm, 3 orders of magnitude lower than as-deposited films. This result suggests that laser post-deposition processing can play an important role in tailoring the properties of ZnO thin films. Excessive laser intensity can compromise structural integrity of the films, however, degrading their electrical transport properties. Notably, the electrical resistance of laser-annealed ZnO films exhibited high sensitivity to oxygen concentration in the surrounding atmosphere, suggesting exciting prospects for application in devices based on transparent oxygen sensors. This study thus positions ultra-short pulsed laser annealing as a versatile post-deposition method for fine-tuning the properties of ZnO thin films, enabling their use in advanced optoelectronic and gas-sensing technologies, particularly on temperature-sensitive substrates., The authors gratefully acknowledge the financial support from EU project SPRINT (H2020-FETOPEN 801464), Spanish projects PID2020-113034RB-I00 (funded by MCIN/AEI/10.13039/501100011033) and PID2023-146041OB-C21 (funded by MICIU/AEI/10.13039/501100011033 and ERDF/EU) and from Gobierno de Aragón (research group T54_23R). The authors would like to acknowledge the use of “Servicio General de Apoyo a la Investigación (SAI)” and the Spanish National Facility ELECMI ICTS, node “Laboratorio de Microscopías Avanzadas (LMA)” at the University of Zaragoza. A. Frechilla and J. Frechilla acknowledge support from Gobierno de Aragón via predoctoral contracts., Peer reviewed
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Generating colours through a novel approach based on spatial ALD and laser processing

  • Frechilla, A.
  • Sekkat, A.
  • Dibenedetto, M.
  • lo Presti, F.
  • Porta-Velilla, L.
  • Martínez, E.
  • de La Fuente, G.F.
  • Angurel, L.A.
  • Muñoz-Rojas, D.
This work studies the combination of direct femtosecond laser structuring of metal surfaces and Spatial Atomic Layer Deposition (SALD) of metal oxides as a novel approach to generate colours on different types of day-to-day metallic objects. In particular, a stainless-steel knife and an outdated 25 ct Dutch florin coin have been selected for the study. Our results show that it is possible both, to preserve the iridescence properties produced by laser processing and to tune the final metal surface colour by controlling the thickness of the ZnO coating. At the same time, this oxide coating could act as a protecting layer for the original material. We thus explore two different strategies to generate colour, namely, iridescence and interference, which can be even developed selectively. This novel methodology to colour metallic surfaces is a promising route to achieve cheap, scalable, and high-throughput processing methods and opens up a new avenue of possibilities and applications related to colour.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Laser-induced scanning transfer deposition of silver electrodes on glass surfaces: A green and scalable technology

  • Molina R.
  • Ertugrul M.
  • Larrea Á.
  • Navarro R.
  • Rico V.
  • Yubero F.
  • González-Elipe A.R.
  • Fuente G.F. de la
  • Angurel L.A.
A pulsed laser ablation backwriting technique with high repetitive rates is implemented for the fabrication of silver coatings on glass surfaces. This method enables geometrical constraint-free deposition of metallic coatings. These exhibit sufficiently low electrical resistance to be used as electrodes in dielectric barrier discharge (DBD) plasma elements. Ambient air deposition of metallic silver electrodes on standard glass slides is explored using a sub-ns UV laser source, combined with hybrid beam scanning methods. The green nature of the overall deposition process includes a preliminary irradiation scan to homogenise the target surface before the subsequent backwriting step. Metal transfer is achieved by combining two phenomena within a simple beam scanning process: LIRT (laser-induced reverse transfer) of silver from the target to the glass, with a partial and secondary LIFT (Laser-Induced Forward Transfer) of silver from the glass to the target. Appropriate selection of pulse energy and pulse repetition rates, beam scanning velocities and target motion enable the growth of sufficiently thick Ag deposits on glass with the required low electrical resistivity and nearly 2D constraint-free geometry. This method avoids the use of vacuum and liquids, resulting in a cheap, facile and green methodology for the deposition of silver electrodes onto transparent substrate surfaces.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Laser annealing of transparent ZnO thin films: a route to improve electrical conductivity and oxygen sensing capabilities

  • Frechilla, A.
  • Frechilla, J.
  • Angurel, L. A.
  • Toldrá-Reig, F.
  • Balas, F.
  • Martínez, E.
  • de La Fuente, G. F.
  • Muñoz-Rojas, D.
The chemical deposition of high-performance zinc oxide (ZnO) thin films is challenging, thus significant efforts have been devoted during the past decades to develop cost-effective, scalable fabrication methods in gas phase. This work demonstrates how ultra-short-pulse laser beam scanning (LBS) can be used to modulate electrical conductivity in ZnO thin films deposited on soda–lime glass by spatial atomic layer deposition (SALD), a high-throughput, low-temperature deposition technique suitable for large-area applications. By systematically optimizing laser parameters, including pulse energy and hatching distance, significant improvements in the electrical performance of 90 nm-thick ZnO films were achieved. The optimization of the laser annealing parameters – 0.21 μJ per pulse energy and a 1 μm hatching distance—yielded ZnO films with an electrical resistivity of (9 ± 2) × 10−2 Ω cm, 3 orders of magnitude lower than as-deposited films. This result suggests that laser post-deposition processing can play an important role in tailoring the properties of ZnO thin films. Excessive laser intensity can compromise structural integrity of the films, however, degrading their electrical transport properties. Notably, the electrical resistance of laser-annealed ZnO films exhibited high sensitivity to oxygen concentration in the surrounding atmosphere, suggesting exciting prospects for application in devices based on transparent oxygen sensors. This study thus positions ultra-short pulsed laser annealing as a versatile post-deposition method for fine-tuning the properties of ZnO thin films, enabling their use in advanced optoelectronic and gas-sensing technologies, particularly on temperature-sensitive substrates.
Dipòsit Digital de Documents de la UAB
Publication Artículo científico (JournalArticle)

Synthesis of 2D porous crystalline materials in simulated microgravity

  • Contreras Pereda, Noemí|||0000-0002-8164-3977
  • Rodríguez-San-Miguel, David|||0000-0002-1476-2175
  • Franco, Carlos|||0000-0003-3385-2851
  • Sevim, Semih
  • Vale, Joao Pedro
  • Solano, Eduardo|||0000-0002-2348-2271
  • Fong, Wye-Khay
  • Del Giudice, Alessandra
  • Galantini, Luciano|||0000-0001-5484-2658
  • Pfattner, Raphael|||0000-0002-7232-1845
  • Pané i Vidal, Salvador|||0000-0003-0147-8287
  • Sotto Mayor, Tiago
  • Ruiz-Molina, Daniel|||0000-0002-6844-8421
  • Puigmarti-Luis, Josep|||0000-0002-7510-9815
To date, crystallization studies conducted in space laboratories, which are prohibitively costly and unsuitable to most research laboratories, have shown the valuable effects of microgravity during crystal growth and morphogenesis. Herein, an easy and highly efficient method is shown to achieve space-like experimentation conditions on Earth employing custom-made microfluidic devices to fabricate 2D porous crystalline molecular frameworks. It is confirmed that experimentation under these simulated microgravity conditions has unprecedented effects on the orientation, compactness and crack-free generation of 2D porous crystalline molecular frameworks as well as in their integration and crystal morphogenesis. It is believed that this work will provide a new "playground" to chemists, physicists, and materials scientists that desire to process unprecedented 2D functional materials and devices.