Skip to main content

EL ALMACENAMIENTO DE ENERGIA TERMICA COMO HERRAMIENTA DE MEJORA DE LA EFICIENCIA ENERGETICA EN LA INDUSTRIA

ENE2011-22722

•
Funding agency name Ministerio de Ciencia e Innovación
Funding agency acronym MICINN
Program Programa Nacional de Proyectos de Investigación Fundamental
Subprogram Subprograma de Proyectos de Investigación Fundamental no Orientada
Call Proyectos I+D
Call year 2011
State Plan 2008-2011 Plan Nacional de Investigación Científica, Desarrollo e Innovación Tecnológica
Management unit Subdirección General de Proyectos de Investigación
Beneficiary centre UNIVERSIDAD DE LLEIDA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 85
Encontrada(s) 1 página(s)

Repositori Obert UdL
Publication Artículo científico (JournalArticle)

Experimental analysis of hydroquinone used as phase change material (PCM) to be applied in solar cooling refrigeration, Analyse expérimentale de l'hydroquinone utilisée comme matériau à changement de phase dans les applications de refroidissement solaire

  • Gil, Antoni
  • Oró Prim, Eduard
  • Miró, Laia
  • Peiró Bell-lloch, Gerard
  • Ruiz-Pardo, Álvaro
  • Salmerón, José Manuel
  • Cabeza, Luisa F.
This present paper is focused on the study of high temperature thermal energy storage (TES) using phase change materials (PCM) to be applied on cooling and refrigeration systems by solar cooling. Thus, a pilot plant with a working temperature range between 150 and 200 C was designed and built at the University of Lleida (Spain). Hydroquinone was selected for the specific application from different PCM candidates as the most suitable material after a literature review and a differential scanning calorimetry (DSC) analysis. This PCM has a phase change temperature range between 166 C and 173 C and a melting enthalpy of 225 kJ kg 1. Two storage configurations were evaluated using the same PCM to have preliminary results before the final storage tank design. From the pilot plant results and experience, a 5 Tn PCM storage tank was designed and built to work in a real solar cooling installation in Seville (Spain)., The work is partially funded by the Spanish government (ENE2011-22722). The authors would like to thank the Catalan Government for the quality accreditation given to their research group GREA (2009 SGR 534). Antoni Gil would like to thank the Col·legi d'Enginyers Industrials de Catalunya for his research appointment. Eduard Oró would like to thank the University of Lleida for his research fellowship.
Repositori Obert UdL
Publication Artículo científico (JournalArticle)

A correlation of the convective heat transfer coefficient between an air flow and a phase change material plate

  • Gracia Cuesta, Alvaro de
  • David, Damien
  • Castell, Albert
  • Cabeza, Luisa F.
  • Virgone, Joseph
This paper provides a new correlation to determine the heat transfer coefficient between an air flow and a plate made of phase change material (PCM). This correlation was built for the simulation of heat storage units containing PCM plates subjected to an inlet temperature step. The presented correlation has the following form: NuPCM x;t ¼ NuPSM$f PCM. The first term NuPSM is for a plate made of traditional material. The term fPCM is a perturbation due to the phase change in the plate. Each term depends on 5 non-dimensional parameters. One of them represents the advance in the total heating or cooling process, in order to take into account the transient evolution of the convective coefficient. The correlations are built using the Least Squares Method, from series of CDF simulation data. The shape of the perturbation fPCM reveals a complex evolution of the temperature repartition in the PCM plate. Finally, a nodal model of the plate has been developed in order to test the provided new correlation and other correlations available in the literature. The results obtained with the present correlation show better agreements with the CFD results, which make this correlation suitable for the simulation of PCM heat storage systems., This work was supported by the “Corporación Tecnológica de Andalucía” by means of the project “MECLIDE-Soluciones estructurales con materiales especiales para la climatización diferida de edificios” with the collaboration of DETEA. The work was partially funded by the Spanish Government (ENE2011-22722 and ULLE10-4E-1305) and the European Union (COST Action COST TU0802). The authors would like to thank the Catalan Government for the quality accreditation given to their research group (2009 SGR 534).
Repositori Obert UdL
Publication Artículo científico (JournalArticle)

Corrosion of metal and metal alloy containers in contact with phase change materials (PCM) for potential heating and cooling applications

  • Moreno Argilés, Pere
  • Miró, Laia
  • Barreneche Güerisoli, Camila
  • Solé Cutrona, Cristian
  • Martorell, Ingrid
  • Cabeza, Luisa F.
Thermal energy storage (TES) using phase change materials (PCM) can be used for load shaving or peak load shifting when coupled to a heating, ventilation, and air-conditioning (HVAC) system such as heat pump. In these systems the PCM is embedded in packages or used in bulk, so the compatibility of the encapsulation materials and the PCM is a key factor to ensure long operational life of the system. Although corrosion caused by salts is known from the chemical industry, when these salts are used as PCM no corrosion data is available, since the salts are used without being in water solution. Producing new corrosion data is essential for PCM utilisation in new applications. In this study the corrosion rate of two metals and two metal alloys when they are in contact with different salt hydrate PCM is evaluated; in total eleven PCM, being four of them commercial PCM, are tested. Since they are PCM to be used for heating and cooling applications they are classified in two different groups to present the corrosion study. Results present the recommendation of using each PCM with the different metals and metal alloys according to the obtained corrosion rate and visual observation of the samples., The work is partially funded by the Spanish Government (ENE2011-22722 and ENE2011-28269-C03-02).
Repositori Obert UdL
Publication Artículo científico (JournalArticle)

Methodologies to estimate industrial waste heat potential by transferring key figures: a case study for Spain

  • Miró, Laia
  • Brueckner, Sarah
  • McKenna, Russell
  • Cabeza, Luisa F.
In the current European energy context, the use of recovered industrial waste heat provides an attractive opportunity to substitute primary energy consumption by a low-emission and low-cost energy carrier. In the case of industrial waste heat, this potential is currently not only largely untapped, but also unaccounted for. In order to achieve a widespread use of recovered industrial waste heat, assessments with a large scope and high spatial resolution are needed. Three methods published in the period 2002–2010 have been found in the literature, which are potentially transferable to other regions. These three methods are based on either the energy consumption of each manufacturing sector or the individual site CO2 emissions. The scope of this analysis is, first, to investigate in how far a transfer of the figures to different countries or regions is sensible in comparison to former studies in the literature. In the process, some uncertainties when transferring methods were identified (different definitions of industry, different standard industrial activities classifications or no standard at all, etc.). The second goal is, once the methodology is accepted, to apply it to a case study, in this case the industrial sector in Spain and two of its counties (Catalonia and the Basque Country) for the years 2001, 2009, 2010 and 2013. In this period, and based on the different approaches employed, the Spanish annual industrial waste heat potential ranges from 54.3 to 151.1 PJ, Catalonia from 8.6 to 29.7 PJ, and from 7.2 to 11.9 PJ for the Basque Country. The methods are considered highly transferable but uncertainties inevitably arise in the case that the source and destination industrial sectors are very different., The work is partially funded by the Spanish government (ENE2011-22722 and ULLE10-4E-1305) and by BMWi Federal Ministry for Economic Affairs and Energy in Germany (Project FKZ 0327383B Mobile Sorption Heat Storage). The authors would like to thank the Catalan Government for the quality accreditation given to their research group GREA (2014 SGR 123). This project has received funding from the European Commission Seventh Framework Programme (FP/2007-2013) under Grant agreement N°PIRSES-GA-2013-610692 (INNOSTORAGE) and from the European Union’s Horizon 2020 research and innovation programme under grant agreement No. 657466 (INPATH-TES). Laia Miró would like to thank the Spanish Government for her research fellowship (BES-2012-051861).
Repositori Obert UdL
Publication Artículo científico (JournalArticle)

Review on phase change materials (PCMs) for cold thermal energy storage applications

  • Oró Prim, Eduard
  • Gracia Cuesta, Alvaro de
  • Castell, Albert
  • Farid, Mohammed M.
  • Cabeza, Luisa F.
Thermal energy storage (TES) is a technology with a high potential for different thermal applications. It is well known that TES could be the most appropriate way and method to correct the gap between the demand and supply of energy and therefore it has become a very attractive technology. In this paper, a review of TES for cold storage applications using solid–liquid phase change materials has been carried out. The scope of the work was focussed on different aspects: phase change materials (PCMs), encapsulation, heat transfer enhancement, and the effect of storage on food quality. Materials used by researchers as potential PCM at low temperatures (less than 20 C) are summarized and some of their thermophysical properties are reported. Over 88 materials that can be used as PCM, and about 40 commercially available PCM have been listed. Problems in long term stability of the materials, such as corrosion, phase segregation, stability under extended cycling or subcooling are discussed. Heat transfer is considered both from theoretical and experimental point of view and the different methods of PCM encapsulation are reviewed. Many applications of PCM at low temperature can be found, such as, ice storage, conservation and transport of temperature sensitive materials and in air conditioning, cold stores, and refrigerated trucks., The work partially funded by the Spanish Government (ENE2008-06687-C02-01/CON and ENE2011-22722) and the European Union (COST Action COST TU0802 and project EFFIBUILDINGS – FP7-PEOPLE-2009-IIF-/-253914). The authors would like to thank the Catalan Government for the quality accreditation given to their research group (2009 SGR 534). Eduard Oró would like to thank the University of Lleida for his research fellowship.
Repositori Obert UdL
Publication Artículo científico (JournalArticle)

Comparison of phase change slurries: Physicochemical and thermal properties

  • Giro-Paloma, Jessica
  • Barreneche Güerisoli, Camila
  • Martínez, Mònica
  • Šumiga, Boštjan
  • Cabeza, Luisa F.
  • Fernández Renna, Ana Inés
Phase change slurries (PCS) consist on a carrier fluid binary system, where water is mostly used as continuous phase and micro-encapsulated phase change materials (MPCM) are used as dispersed phase. PCS are used in Thermal Energy Storage (TES) for building applications, combining the latent heat capacity of the MPCM with the sensible heat capacity of the carrier fluid, and at the same time giving the PCM pumpable properties. In this study, two PCS samples are compared and characterized, the commercial Micronal® DS 5007 X from BASF and a laboratory made PCS28. Thereby, in this paper thermal stability is studied by using thermogravimetrical analysis (TGA) and the main components of the MPCM have been studied using Fourier transformed infrared spectroscopy (FT-IR). Moreover, TGA coupled with FT-IR is used to study deeply the thermal decompositions of the PCS microcapsules and products derived thereof. Finally, differential scanning calorimetry (DSC) is performed to study the melting enthalpy and the melting temperature range of the phase change material (PCM). This paper concludes that both types of PCS have good potential from thermal energy storage purposes such as solar space heating applications., The work is partially funded by the Spanish government (ENE2011-28269-C03-02 and ENE2011-22722). The authors would like to thank the Catalan Government for the quality accreditation given to their research group GREA (2014 SGR 123) and research group DIOPMA (2014 SGR 1543). The research leading to these results has received funding from the European Union's Seventh Framework Programme (FP7/2007-2013) under grant agreement n° PIRSES-GA-2013-610692 (INNOSTORAGE).
Repositori Obert UdL
Publication Artículo científico (JournalArticle)

Thermomechanical testing under operating conditions of A516Gr70 used for CSP storage tanks

  • Prieto, Cristina
  • Barreneche Güerisoli, Camila
  • Martínez, Mònica
  • Cabeza, Luisa F.
  • Fernández Renna, Ana Inés
Thermal energy storage (TES) in molten salts is the storage dominating technology in solar power applications today. In two-tank molten salt storage systems energy density ranges from 30 to 70 kW h/m3 are achievable. The salt material used is a binary system, composed of 60% NaNO3 and 40% KNO3. In the 8 MWhth pilot plant built and tested by Abengoa, the storage tanks were made of steel A516Gr.70 using the Appendix M of code API 650 for their design. A specific testing device was developed to evaluate thermo-mechanical properties, and a study was conducted in order to evaluate tensile properties of A516Gr.70 specimens under operation conditions for the hot tank at the pilot plant that is in contact with molten salts at 380 °C. Results confirmed the outcomes of the work: the reduction of the yield limit, elongation before fracture, and Young modulus at 380 °C after having been 5 min immersed in molten salts. Moreover, after a creep-test simulating operating 7 days conditions during, an additional reduction of the yield limit was measured., The research leading to these results has received funding from Spanish government (Fondo tecnológico IDI-20090393, ConSOLida CENIT 2008-1005). The work is partially funded by the Spanish government (ENE2011-28269-C03-02, ENE2011-22722, ENE2015-64117-C5-1-R, and ENE2015-64117-C5-2-R). The research leading to these results has received funding from the European Union's Seventh Framework Programme (FP7/2007-2013) under grant agreement n° PIRSES-GA-2013-610692 (INNOSTORAGE) and from the European Union’s Horizon 2020 research and innovation programme under grant agreement No 657466 (INPATH-TES). The authors would like to thank the Catalan Government for the quality accreditation given to their research groups GREA (2014 SGR 123) and research group DIOPMA (2014 SGR 1543). Dr. Camila Barreneche would like to thank Ministerio de Economía y Competitividad de España for Grant Juan de la Cierva FJCI-2014-22886.
Repositori Obert UdL
Publication Artículo científico (JournalArticle)

Control of a PCM ventilated facade using reinforcement learning techniques

  • Gracia Cuesta, Alvaro de
  • Fernàndez Camon, César
  • Castell, Albert
  • Mateu Piñol, Carles
  • Cabeza, Luisa F.
Artificial intelligence techniques have been successfully applied to control dynamic systems looking for an optimal control. Among those techniques, reinforcement learning has been shown as particularly effective at reducing the dimensionality of some real problems and solving control problems by learning from experience. The use of thermal energy storage active systems in the building sector is identified as suitable option to reduce their energy demand for heating and cooling. However, these systems might be expensive and require appropriate control strategies in order to improve the performance of the building. In this paper a ventilated facade with PCM is controlled using a reinforcement learning algorithm. The ventilated facade uses mechanical ventilation during nighttime to solidify the PCM and releases this cold stored to the inner environment during the peak demand period. It is crucial to decide correctly the schedule of charge and discharge process of the PCM according to the weather and indoor conditions. An experimentally validated numerical model is used to test the performance of the control algorithm under different weather conditions. Important improvements on the energy savings due to the use of control strategies were found and supported by the data under the different tested climatic conditions., The work partially funded by the Spanish government (ENE2011-28269-C03-01, ENE2011-22722 and ULLE10-4E-1305). The authors would like to thank the Catalan Government for the quality accreditation given to their research group (2014-SGR-123). The research leading to these results has received funding from the European Union’s Seventh Framework Programme (FP7/2007-2013) under grant agreement #PIRSES-GA-2013-610692 (INNOSTORAGE). Alvaro de Gracia would like to thank Education Ministry of Chile for Grant PMI ANT1201.
Repositori Obert UdL
Publication Artículo científico (JournalArticle)

The use of phase change materials in fish farms: a general analysis

  • Zsembinszki, Gabriel
  • Solé Cutrona, Cristian
  • Castell, Albert
  • Pérez Luque, Gabriel
  • Cabeza, Luisa F.
Aquaculture has become an important sector of animal food production thanks to a fast and continuous growth over the last few decades. Both marine and fresh water fish can be reared in fish farms, and there are species that are mainly produced by aquaculture rather than capture. As most of the reared fish species are sensible to water temperature and its fluctuations, having the control of this parameter in fish farms becomes an important issue that has to be taken into account. In this paper, three different fish farms are studied by simulating the water temperature when a thermal energy storage (TES) system using phase change materials (PCMs) is implemented. The effect and the estimated amounts of PCM required in each particular case are also analyzed. The results show that appreciable effects can be obtained, especially when the TES unit is used in combination with auxiliary sources of energy, such as solar collectors., The work was partially funded by the Spanish Government (ENE2011-22722). The authors would like to thank the Catalan Government for the quality accreditation given to their research group (2009 SGR 534).
Repositori Obert UdL
Publication Artículo científico (JournalArticle)

TES-PS10 postmortem tests: Carbon steel corrosion performance exposed to molten salts under relevant operation conditions and lessons learnt for commercial scale-up

  • Ruiz-Cabañas, F. Javier
  • Prieto, Cristina
  • Madina, Virginia
  • Fernández Renna, Ana Inés
  • Cabeza, Luisa F.
Postmortem tests were performed over components removed from the TES-PS10 pilot plant after almost four years of continuous operation being exposed to solar salts under representative commercial operation conditions. Accordingly, corrosion performance of plates sections extracted from both storage tanks and samples cut from the hot molten salts pump were evaluated. Corrosion damage extension, oxides layers morphology, and corrosion products chemistry were analyzed by X-ray diffraction, energy dispersive X-ray spectrometry, optical microscopy, and SEM. In addition to materials compatibility with molten salts, mechanical tests were carried out over the storage tanks plates sections. Although the corrosion damage extension over the plates extracted from storage tanks was low and the mechanical properties were according to the standard, some interesting observations were seen. For example, a sample extracted from the hot storage tank and exposed to intermittent contact with molten salts showed some areas characterized by the growth of a non-protective oxide scale. Moreover, localized corrosion with slight penetration through the base material was identified for all storage plates samples under evaluation. On the other hand, the molten salt pump parts under study showed adherent and uniform oxides layers without detecting corrosion–erosion phenomena. Some cavities were found in the discharge elbow, and these imperfections were associated to a bad metallurgical quality during casting. Summarizing, corrosion phenomena suffered by the components under evaluation could be corrected in future plants by applying the lessons learned discussed in this study. As conclusion, materials selection analyzed within this postmortem evaluation is valid from the corrosion point of view to be used in the design of commercial TES systems in PTC plants., The research leading to these results has received funding from Spanish government (Fondo tecnológico IDI-20090393, ConSOLida CENIT 2008-1005). The work is partially funded by the Spanish Government (ENE2011-28269-C03-02, ENE2011-22722, ENE2015-64117-C5-1-R, and ENE2015-64117-C5-2-R). The authors would like to thank the Catalan Government for the quality accreditation given to their research group GREiA (2017 SGR 1537) and research group DIOPMA (2017 SGR 138). GREiA and DIOPMA are certified agents TECNIO in the category of technology developers from the Government of Catalonia.
Repositori Obert UdL
Publication Artículo científico (JournalArticle)

Corrosion of metal containers for use in PCM energy storage

  • Ferrer, Gerard
  • Solé, Aran
  • Barreneche Güerisoli, Camila
  • Martorell, Ingrid
  • Cabeza, Luisa F.
In recent years, thermal energy storage (TES) systems using phase change materials (PCM) have been widely studied and developed to be applied as solar energy storage units for residential heating and cooling. These systems performance is based on the latent heat due to PCM phase change, a high energy density that can be stored or released depending on the needs. PCM are normally encapsulated in containers, hence the compatibility of the container material with the PCM has to be considered in order to design a resistant container. Therefore, the main aim of this paper is to study the corrosion effects when putting in contact five selected metals (aluminium, copper, carbon steel, stainless steel 304 and stainless steel 316) with four different PCM (one inorganic mixture, one ester and two fatty acid eutectics) to be used in comfort building applications. Results showed corrosion on aluminium specimens. Hence caution must be taken when selecting it as an inorganic salt container. Despite copper has a corrosion rate range of 6e10 mg/cm2 yr in the two fatty acid formulations tested, it could be used as container. Stainless steel 316 and stainless steel 304 showed great corrosion resistance (0e1 mg/cm2 yr) and its use would totally be recommended with any of the studied PCM., The work is partially funded by the Spanish Government (ENE2011-28269-C03-02 and ENE2011-22722). The authors would like to thank the Catalan Government for the quality accreditation given to their research groups GREA (2014 SGR 123) and research group DIOPMA (2014 SGR 1543). Aran Sole would like to thank the Departament d'Universitats, Recerca i Societat de la Informacio de la Generalitat de Catalunya for her research fellowship. The research leading to these results has received funding from the European Union's Seventh Framework Programme (FP7/2007- 2013) under grant agreement n PIRSES-GA-2013-610692 (INNOSTORAGE)
Repositori Obert UdL
Publication Artículo científico (JournalArticle)

Review of technology: Thermochemical energy storage for concentrated solar power plants

  • Prieto, Cristina
  • Cooper, Patrick
  • Fernández Renna, Ana Inés
  • Cabeza, Luisa F.
To be able to extend the operation of a solar power plant (CSP) up to 15 h, thermal energy storage (TES) is necessary. But TES also provides more versatility to the plant and makes its reliance during operation hours more dependable. On the other hand, due to the different CSP configurations, a broad spectrum of storage technologies, materials and methods is needed. Sensible and latent heat storage are known technologies in CSP, but thermochemical storage (TCS) is still very much at laboratory level. Nevertheless, TCS has de advantage of nearly no losses during storage and very good volumetric energy density. This review summarizes and compares the different TCS that are today being investigated. Those systems are based in three redox reactions, sulfur-based cycles, metal oxide reduction–oxidation cycles, and perovskite-type hydrogen production, and metal oxide non-redox cycles due to their similarity. This review shows that all these cycles are promising, but none of them seems to have all the characteristics necessary to become the only one storage system for CSP. The main conclusion of the review is that the calcium carbonate is the cycle with most experimentation behind it to infer that it could be viable and should thus be attempted at a research plant scale once a reactivation cycle can be designed; and the manganese oxide cycle, while less developed, is fundamental enough to be a suitable application for desert climates over the rest of the water-frugal or even water-avoiding cycles., The work was partially funded by the Spanish government (project ENE2011−22722). The authors would also like to thank the Catalan Government for the quality accreditation given to their research group GREA (2014 SGR 123) and DIOPMA (2014 SGR 1543). The research leading to these results has received funding from the European Union׳s Seventh Framework Programme (FP7/2007−2013) under Grant agreement n° PIRSES-GA−2013−610692 (INNOSTORAGE).
Repositori Obert UdL
Publication Artículo científico (JournalArticle)

Enthalpy-temperature plots to compare calorimetric measurements of phase change materials at different sample scales

  • Rathgeber, Christoph
  • Schmit, Henri
  • Miró, Laia
  • Cabeza, Luisa F.
  • Gutiérrez, Andrea
  • Ushak, Svetlana
  • Hiebler, Stefan
Phase change materials (PCM) can provide high thermal energy storage capacities in narrow temperature ranges around their phase change temperature. The expectable maximum storage capacity of a PCM in a defined temperature range is equal to the enthalpy change in that range and can be determined via calorimetric measurements such as differential scanning calorimetry (DSC) or T-History calorimetry. T-History samples (aprox. 15 ml) are about 1000 times larger than DSC samples (aprox. 15 ml). Experiments in a pilot plant are performed to study the charging and discharging behaviour of even larger amounts of the PCM (aprox. 150 l). The common practise is to investigate PCM at one scale, rarely at two scales. In this work, the characterisation was carried out at three scales (DSC, T-History, and pilot plant) for four PCM (RT58, bischofite, D-mannitol, and hydroquinone). Thereby, the question arises how the enthalpy changes measured at different scales and under different conditions can be compared. In literature, the melting enthalpy is usually assigned to a single temperature without indicating the temperature range considered for evaluation. In very few instances, the enthalpy change within a defined temperature range is stated. In both cases, results measured under different conditions are difficult to compare. In this work, it is demonstrated that enthalpy-temperature plots facilitate the comparison and interpretation of measurements obtained under different experimental methods at different sample scales., The work of ZAE Bayern was part of the project EnFoVerM and was supported by the German Federal Ministry for Economic Affairs and Energy under the project code 0327851D. The work at the University of Lleida is partially funded by the Spanish government (ENE2011-22722, ENE2015-64117-C5-1-R (MINECO/FEDER) and ULLE10-4E-1305). The authors would like to thank the Catalan Government for the quality accreditation given to their research group GREA (2014 SGR 123). GREA is a certified agent TECNIO in the category of technology developers from the Government of Catalonia. The research leading to these results has received funding from the European Union's Seventh Framework Programme (FP7/2007-2013) under grant agreement n° PIRSES-GA-2013-610692 (INNOSTORAGE) and from the European Union’s Horizon 2020 research and innovation programme under grant agreement No 657466 (INPATH-TES). The authors want also to thank the collaboration of Antoni Gil from Massachusetts Institute of Technology (USA), Eduard Oró from Catalonia Institute for Energy Research (Spain), and Jaume Gasia and Gerard Peiró from University of Lleida (Spain). Laia Miró would like to thank the Spanish Government for her research fellowship (BES-2012-051861). The work of the University of Antofagasta was supported by FONDAP SERC-Chile (grant N° 15110019), and the Education Ministry of Chile Grant PMI ANT 1201. Authors thank the SALMAG Company for providing of bischofite. Andrea Gutierrez would like to acknowledge to the Ministry of Education of Chile her doctorate scholarship ANT 1106 and CONICYT/PAI N° 7813110010.
Repositori Obert UdL
Publication Artículo científico (JournalArticle)

Selection and characterization of recycled materials for sensible thermal energy storage

  • Navarro, Maria E.
  • Martínez, Mònica
  • Gil, Antoni
  • Fernández Renna, Ana Inés
  • Cabeza, Luisa F.
  • Olives, R.
  • Py, Xavier
Alternative low cost materials are evaluated through the valorization of by-products derived from mining and metallurgical industry for solid sensible heat based energy storage systems. They were used either as received or formulated as aggregates in mortars, and their thermal and mechanical properties were characterized. A selection methodology was applied in order to compare them with available materials found in the literature for applications as (STES) materials, and with materials from Cambridge Educational Software (CES) Selector database. It was demonstrated that these recycled materials have a high potential for these thermal energy storage applications., This work was partially funded by the Spanish Government (Project ENE2008-06687-C02-01/CON and ENE2011-22722) and the European Union (COST Action COST TU0802). The authors at DIOPMA and GREA-UdL would like to thank the Catalan Government for the quality accreditation given to their research group, 2009 SGR 645 and 2009 SGR534 respectively. Antoni Gil would like to thank the Col·legi d'Enginyers Industrials de Catalunya for his research appointment and the Departament d'Universitats, Recerca i Societat de la Informació of Generalitat de Catalunya for the AGAUR research stage scholarship (BE-DGR 2010).
Repositori Obert UdL
Publication Artículo científico (JournalArticle)

Review of the T-history method to determine thermophysical properties of phase change materials (PCM)

  • Solé, Aran
  • Miró, Laia
  • Barreneche Güerisoli, Camila
  • Martorell, Ingrid
  • Cabeza, Luisa F.
Phase change materials (PCM) are able to store thermal energy when becoming liquid and to releaseit when solidifying. Latent heat storage has gained importance due the applications towards increasing energy efficiency in severalsystems. Thus, a correct and accurate thermal characterization of these materials should be achieved. Among all possible thermal analysis methods to determine PCM thermophysical properties, the T-history method presents certain advantages. The T-history method is known to be suitable to obtain fusion enthalpy, specific heat and thermal conductivity for large phase change materials samples. On the other hand, no experimental T-history equipment isc ommercially available yet. Therefore, the goal of this paper is moving towards a consensus. To achieve this goal, a collection of similar methods previous to T-history are exposed and different proposals based on improving the original T-history method are discussed and reviewed., he work is partially funded by the Spanish government (ENE2011-28269-C03-02 and ENE2011-22722). The authors would like to thank the Catalan Government for the quality accreditation given to the research group GREA (2009 SGR 534). Aran Solé would like to thank the Departament d'Universitats, Recerca i Societat de la Informació de la Generalitat de Catalunya for her research fellowship. Laia Miró would like to thank the Spanish Government for her research fellowship (BES-2012-051861).
Repositori Obert UdL
Publication Artículo científico (JournalArticle)

Computational efficiency in numerical modeling of high temperature latent heat storage: comparison of selected software tools based on experimental data

  • Pointner, Harald
  • Gracia Cuesta, Alvaro de
  • Vogel, Julian
  • Tay, N. H. Steven
  • Liu, Ming
  • Johnson, Maike
  • Cabeza, Luisa F.
In this article, four different numerical models for the investigation of phase change processes within latent heat storage are described and compared concerning accuracy, convergence behavior and computational efficiency. The models are based on different types of discretization, make use of different ways to model phase change and are implemented with C, MATLAB or ANSYS CFX. After a brief introduction into each investigated numerical model, the experimental reference setup is described. It consists of a flat plate latent heat storage with the eutectic mixture NaNO3 (46 wt%)–KNO3 (54 wt%) with a measured melting temperature of 219.5 °C as storage material. Based on the corresponding simulation model developed in this paper, the comparison of the numerical models is achieved. This methodology allows the investigation of the numerical performance of different software tools in the context of high temperature latent heat storage that was not achieved thus far. All four numerical models show good agreement to experimental results but differ significantly in speed and convergence behavior., This work was partially funded by the nextPCM project supported by the German Federal Ministry for the Environment, Nature Conservation and Nuclear Safety. Moreover, the work was partially funded by the Spanish government (ENE2011-22722 and ULLE10-4E-1305). The authors Alvaro de Gracia and Luisa F. Cabeza would like to thank the Catalan Government for the quality accreditation given to their research group (2014-SGR-123). The research leading to parts of these results has received funding from the European Union’s Seventh Framework Programme (FP7/2007-2013) under grant agreement PIRSES-GA-2013-610692 (INNOSTORAGE). Alvaro de Gracia would like to thank the Education Ministry of Chile for Grant PMI ANT1201.
Repositori Obert UdL
Publication Artículo científico (JournalArticle)

Thermophysical characterization and thermal cycling stability of two TCM: CaCl2 and zeolite

  • Barreneche Güerisoli, Camila
  • Fernández Renna, Ana Inés
  • Cabeza, Luisa F.
  • Cuypers, Ruud
At this moment, the global energy consumption in buildings is around 40% of the total energy consumption in developed countries. Thermal energy storage (TES) is presented as one way to address this energyrelated problem proposing an alternative to reduce the gap between energy supply and energy demand. One way to store energy is using thermochemical materials (TCM). These types of materials allow accumulating energy through a chemical process at low temperature, almost without heat losses. In addition, it is a stable way to perform the heat storage and TCM can be implemented for seasonal storage or/and long term storage. This study compares the cyclability, from the thermophysical point of view, CaCl2 which follows a chemical reaction and zeolite which follows a sorption process to be used as TCM for seasonal/long term storage. The main results show that the chemical reaction TCM is more energy-efficient than the sorption TCM. The CaCl2 calculated energy density is 1.47 GJ/m3 , being the best option to be considered to be used as TCM, even though the dehydration process of the zeolite is simpler and it occurs at higher temperatures its calculated energy density is only 0.2 GJ/m3 ., The research leading to these results has received funding from the European Commission Seventh Framework Programme (FP/ 2007-2013) under grant agreement No ENER/FP7/1295983 (MERITS) and under grant agreement no. PIRSES-GA-2013-610692 (INNOSTORAGE). Furthermore, the work is partially funded by the Spanish government (ENE2011-28269-C03-02 and ENE2011- 22722), and the European Union by Cost Action TU0802. The authors would like to thank the Catalan Government for the quality accreditation given to their research groups GREA (2014 SGR 123) and DIOPMA (2014 SGR 1543).
Repositori Obert UdL
Publication Artículo científico (JournalArticle)

On the use of filters to facilitate the post-optimal analysis of the Pareto solutions in multi-objective optimization

  • Antipova, Ekaterina
  • Pozo, C.
  • Guillén Gosálbez, Gonzalo
  • Boer, Dieter
  • Cabeza, Luisa F.
  • Jiménez Esteller, Laureano
Multi-objective optimization (MOO) has emerged recently as a useful technique in the design andplanning of engineering systems because it allows identifying alternatives leading to significant envi-ronmental savings. MOO models typically contain an infinite number of Pareto solutions, from whichdecision-makers should choose the best one according to their preferences. An approach is here pre-sented that identifies and retains for further inspection a reduced set of Pareto solutions showing betteroverall performance. The capabilities of our approach are illustrated through its application to the designof reverse osmosis desalination plants considering simultaneously the unitary production cost and a setof environmental impacts in several damage categories. Our method reduces significantly the number ofPareto points, thereby facilitating the decision-making process in MOO., The authors would like to acknowledge financial support from the Spanish Government(ENE2011-28269-C03-03, ENE2011-22722, DPI2012-37154-C02-02, CTQ2012-37039-C02) and the Catalan Government for the quality accreditation given to their research groups SUSCAPE and GREA (2009 SGR 545, 2009 SGR 534)
Repositori Obert UdL
Publication Artículo científico (JournalArticle)

Characterization of granular phase change materials for thermal energy storage applications in fluidized beds

  • Izquierdo Barrientos, M. A.
  • Sobrino, C.
  • Almendros Ibáñez, J. A.
  • Barreneche Güerisoli, Camila
  • Ellis, N.
  • Cabeza, Luisa F.
This work investigates commercially available granular phase change materials (PCMs) with different transition temperatures for the use of thermal-energy storage systems in fluidized beds. The hydrodynamic characteristics of granular PCMs were tested in cylindrical-3D and planar-2D fluidized beds. The density, particle size distribution and angle of repose were measured for various PCM materials. Further attrition studies were conducted with changes in particle surface from abrasion, which were characterized using a Scanning Electron Microscope (SEM). The results indicate that some materials with smaller particle size and thinner supporting structure can lose the paraffin during the fluidization process, when paraffin is in a liquid state. As a consequence, the particles agglomerate, and the bed defluidizes. For all of the tested materials, only GR50 (with a transition temperature of 50 °C) properly fluidizes when the paraffin is in the liquid state and has shown to endure >75 h of continuous operation and 15 melting-solidification cycles in a fluidized bed. Additional differential scanning calorimetry (DSC) measurements of the cycled particles did not show a decrease in energy storage capacity of the granular PCM, which corroborates that there is no loss of material after >75 h of fluidization., The work is partially funded by the Spanish government (ENE2010-15403, ENE2011-22722 and ENE2015-64117-C5-1). The authors would like to thank the Catalan Government for the quality accreditation to their research groups GREA (2014 SGR 123). The study that led to these results has received funding from the European Union’s Seventh Framework Programme (FP7/2007-2013) under grant agreement n°n°PIRSES-GA-2013-610692 (INNOSTORAGE) and from the European Union’s Horizon 2020 research and innovation programme under grant agreement No. 657466 (INPATH-TES).
Repositori Obert UdL
Publication Artículo científico (JournalArticle)

Effect of D-mannitol polymorphism in its thermal energy storage capacity when it is used as PCM

  • Barreneche Güerisoli, Camila
  • Seth, Falguni
  • Fernández Renna, Ana Inés
  • Cabeza, Luisa F.
The main objective of this paper is to study the possible use of D-mannitol as phase change material (PCM) for thermal energy storage. PCM are materials that have high phase change enthalpy and this thermophysical property gives them the ability to store energy as latent heat. D-mannitol is a material which has different morphological phases (polymorphism); here were studied b-form and d-form. Different polymorphic forms produce changes on melting point of D-mannitol. For this reason it is necessary to establish a suitable working temperature range for the use of D-mannitol as phase change material. The thermal characterization was performed with DSC analysis using 0.5 K min-1 slow-dynamic method. Polymorphism analysis of D-mannitol was analyzed to associate the thermal behavior obtained by DSC with a specific polymorphic phase. D-mannitol presented three different thermal behaviors: the first one had a melting peak at 167 ºC, the second was a double melting peak at 155 ºC and 166 ºC, and the third a single peak at 155 ºC. Due to irregular results, two working range were studied and through the thermal characterization, it was possible to define a working range where Dmannitol could be used as PCM for energy storage: this range is between 135 and 175 ºC. Furthermore, it was possible to differentiate two crystalline phases of D-mannitol applying FT-IR analysis and to link them with thermal behavior observed in DSC. The percentage of times each thermal behavior is observed in DSC analysis was calculated. d-form is obtained 15.8% of analyzed cycles, the b-form appears 44.7% of times, and an intermediate transition between the two phases is found 39.5% of cycles., The work is partially funded by the Spanish government (ENE2011-22722) and the European Union (COST Action TU0802). The authors would like to thank the Catalan Government for the quality accreditation given to their research group GREA (2009 SGR 534) and research group DIOPMA (2009 SGR 645). A. Gil would like to thank the Col•legi d’Enginyers Industrials de Catalunya for his research appointment.
Repositori Obert UdL
Publication Artículo científico (JournalArticle)

Key performance indicators in thermal energy storage: survey and assessment

  • Cabeza, Luisa F.
  • Galindo, Esther
  • Prieto, Cristina
  • Barreneche Güerisoli, Camila
  • Fernández Renna, Ana Inés
Thermal energy storage (TES) is recognised as a key technology for further deployment of renewable energy and to increase energy efficiency in our systems. Several technology roadmaps include this technology in their portfolio to achieve such objectives. In this paper, a first attempt to collect, organise and classify key performance indicators (KPI) used for TES is presented. Up to now, only KPI for TES in solar power plants (CSP) and in buildings can be found. The listed KPI are quantified in the literature and compared in this paper. This paper shows that TES can only be implemented by policy makers if more KPI are identified for more applications. Moreover, close monitoring of the achievements of the already identified KPI needs to be carried out to demonstrate the potential of TES., The work is partially funded by the Spanish Government (ENE2011-28269-C03-02, ENE2011-22722). The authors would like to thank the Catalan Government for the quality accreditation given to their research group GREA (2014 SGR 123) and research group DIOPMA (2014 SGR 1543). The research leading to these results has received funding from the European Union's Seventh Framework Programme (FP7/2007-2013) under grant agreement n° PIRSES-GA-2013-610692 (INNOSTORAGE).
Repositori Obert UdL
Publication Artículo científico (JournalArticle)

Types, methods, techniques, and applications for microencapsulated phase change materials (MPCM): a review

  • Giro-Paloma, Jessica
  • Martínez, Mònica
  • Cabeza, Luisa F.
  • Fernández Renna, Ana Inés
Phase change materials (PCM) can be employed in many fields because of their capacity to absorb and release energy when it is necessary. Nowadays, the number of studies about these materials is increasing because of their benefits in energy systems. This paper reviews the previous researches and developments on microencapsulated phase change materials (MPCM) in thermal energy storage (TES) systems, focusing on the different methods of encapsulations and also the different applications of these materials. This review aims to be a useful guide for the researchers in this area, because it explains the different types of phase change core materials, the different shells, the methods to microencapsulate these PCM, the most used techniques to characterize these microencapsulated phase change materials, and a revision of the main applications., The work is partially funded by the Spanish government (ENE2011-28269-C03-02 and ENE2011-22722). The authors would like to thank the Catalan Government for the quality accreditation given to their research group GREA (2014 SGR 123) and research group DIOPMA (2014 SGR 1543). The research leading to these results has received funding from the European Union's Seventh Framework Programme (FP7/2007–2013) under Grant agreement no. PIRSES-GA-2013-610692 (INNOSTORAGE).
Repositori Obert UdL
Publication Artículo científico (JournalArticle)

Use of polyethylene glycol for the improvement of the cycling stability of bischofite as thermal energy storage material

  • Gutiérrez, Andrea
  • Ushak, Svetlana
  • Galleguillos, Hector
  • Fernández, Ángel G.
  • Cabeza, Luisa F.
  • Grágeda, Mario
Bischofite is a by-product of the non-metallic mining industry. It has been evaluated as phase change material in thermal energy storage, but it shows little cycling stability, therefore in this paper the mixture of bischofite with an additive was studied. Since polyethylene glycol (PEG) is a PCM itself, in this paper PEG (with different molecular weights) is used as additive in a PCM (bischofite) to improve its thermal behaviour. Results show that adding 5% PEG 2 000 to bischofite gives a more cycling stable PCM without affecting its melting temperature neither decreasing significantly its heat of fusion. This research shows that mixing an inorganic PCM with an organic additive can be a good option to improve the thermal performance of the PCM., The authors would like to acknowledge the collaboration of the company SALMAG. The authors acknowledge to FONDECYT (grant N 1120422), CONICYT/FONDAP N 15110019, and the Education Ministry of Chile Grant PMI ANT 1201 for the financial support. This work was partially funded by the Spanish project ENE2011-22722. Dr. Luisa F. Cabeza would like to acknowledge the Generalitat de Catalunya for the quality recognition 2014-SGR-123. Andrea Gutierrez would like to acknowledge for her doctorate scholarships to the Education Ministry of Chile (ANT 1106) and CONICYT/PAI N7813110010.
Repositori Obert UdL
Publication Artículo científico (JournalArticle)

Materials selection for thermal energy storage systems in parabolic trough collector solar facilities using high chloride content nitrate salts

  • Ruiz-Cabañas, F. Javier
  • Prieto, Cristina
  • Madina, Virginia
  • Fernández Renna, Ana Inés
  • Cabeza, Luisa F.
The increasing role of concentrated solar power (CSP) within the renewable energy portfolio is attributed to the possibility of integrating thermal energy storage (TES) systems. Then, CSP technology has become one of the most interesting clean options to deliver dispatchable power on demand. Nowadays, commercial facilities use high quality solar salts (60%:40% NaNO3 and KNO3 by weight) as storage medium due to the attractive properties of this fluid to be applied under CSP operation conditions. Taking into account that CSP installations are designed with really large TES systems containing tens of thousands of tons, the use of lower quality nitrates salts would reduce the molten salts inventory cost and finally the investment cost of the CSP storage systems at commercial scale. The most important drawback of selecting low quality nitrates salts for high temperature CSP applications is the corrosion impact produced by impurities. Accordingly, chlorides have been identified in the state of the art as the impurity with higher effect over corrosion. This work is focused on A516 Gr70 carbon steel corrosion performance evaluation under high-chlorides content nitrates salts (1.2% and 3% by weight) at 400 °C. In addition, the feasibility of using the proposed low purity mixtures with current CSP facilities materials selection is analyzed. Results reported within this study show the critical effect of chloride content over corrosion mechanism producing lack of adherence between base metal and oxides layers in addition to corrosion products delamination and internal cracking. Then, the use of A516 Gr70 carbon steel is rejected for a long term design under solar salts containing chlorides content in the range 1.2–3% by weight being necessary a higher corrosion resistant materials selection. An improved materials selection focused on higher corrosion resistance alloys is discussed., The research leading to these results has received funding from Spanish government (Fondo tecnológico IDI-20090393, ConSOLida CENIT 2008-1005). The work is partially funded by the Spanish government (ENE2011-28269-C03-02, ENE2011-22722, ENE2015-64117-C5-1-R (MINECO/FEDER), and ENE2015-64117-C5-2-R (MINECO/FEDER)). The authors would like to thank the Catalan Government for the quality accreditation given to their research group GREA (2014 SGR 123) and research group DIOPMA (2014 SGR 1543).
Repositori Obert UdL
Publication Artículo científico (JournalArticle)

Experimental evaluation at pilot plant scale of multiple PCMs (cascaded) vs. single PCM configuration for thermal energy storage

  • Peiró Bell-lloch, Gerard
  • Gasia, Jaume
  • Miró, Laia
  • Cabeza, Luisa F.
The present paper provides on one hand, a literature review of the different studies available in the scientific literature where the concept of multiple phase change materials (PCM) configuration, also named cascaded or multi-stage, has been presented and on the other hand, an experimental evaluation of the advantages of using the multiple PCM configuration instead of the single PCM configuration in thermal energy storage (TES) systems at pilot plant to fill the gap of experimental and high scales studies on this concept in the literature. Two PCM with melting temperatures in a temperature range of 150 e200 C were selected due to their high value of heat of fusion and compared: d-mannitol and hydroquinone. Three configurations were evaluated: (1) single PCM with hydroquinone, (2) single PCM with dmannitol and (3) multiple PCM with hydroquinone and d-mannitol. A discussion regarding the results on the specific energy stored and effectiveness as well as the evolution of the PCM and heat transfer fluid (HTF) through the time and at different and representative locations of the facility is presented. Results showed that the multiple PCMs configuration introduced an effectiveness enhancement of 19.36% if compared with single PCM configuration as well as a higher uniformity on the HTF temperature difference between the inlet and outlet., The work is partially funded by the Spanish Government (ENE2011-22722 and ULLE10-4E-1305). The authors would like to thank the Catalan Government for the quality accreditation given to their research group GREA (2014 SGR 123). The research leading to these results has received funding from the European Union's Seventh Framework Programme (FP7/2007-2013) under grant agreement n PIRSES-GA-2013-610692 (INNOSTORAGE). Laia Miro would like to thank the Spanish Government for her research fellowship (BES-2012-051861).
Repositori Obert UdL
Publication Artículo científico (JournalArticle)

Embodied energy in thermal energy storage (TES) systems for high temperature applications

  • Miró, Laia
  • Oró Prim, Eduard
  • Boer, Dieter
  • Cabeza, Luisa F.
Currently, there is an increasing interest in concentrated solar power (CSP) plants as alternative to produce renewable electricity at large scale by using mirrors to concentrate the solar energy and to convert it into high temperature heat. These facilities can be combined with thermal energy storage (TES) systems, which are, nowadays, one of the most feasible solutions in facing the challenge of the intermittent energy supply and demand. However, they are still in research process and, for that, there is a lack of environmental impact studies of these TES systems complementing solar plants. This paper accounts the environmental impact of three TES systems used nowadays in high temperature applications for CSP plants: first, a system which stores sensible heat in high temperature concrete; second, a system storing sensible heat in molten salts; and third, another system with molten salts but storing latent heat. All the systems are normalised in order to be comparable between them due to its initial storage capacity difference. The environmental impact is accounted by calculating the amount of embodied energy in the components of the different TES systems. Notice that embodied energy refers to the total energy inputs required to make a component. Between the three systems, the sensible heat system using concrete as storage material is the one with less environmental impact while the molten salts and PCM have a higher value of embodied energy, mainly due to the nitrate mixture used as storage material. Finally, advantages and disadvantages of the method proposed used are discussed, The work was partially funded by the Spanish government (project ENE2011-22722). The authors would like to thank the Catalan Government for the quality accreditation given to their research group GREA (2009 SGR 534). The research leading to these results has received funding from the European Union’s Seventh Framework Programme (FP7/2007-2013) under Grant agreement n PIRSES-GA-2013-610692 (INNOSTORAGE). Eduard Oró would like to thank the University of Lleida for his research fellowship. Laia Miró would like to thank the Spanish Government for her research fellowship (BES-2012-051861).
Repositori Obert UdL
Publication Artículo científico (JournalArticle)

Influence of the heat transfer fluid in a CSP plant molten salts charging process

  • Peiró Bell-lloch, Gerard
  • Gasia, Jaume
  • Miró, Laia
  • Prieto, Cristina
  • Cabeza, Luisa F.
The selection of a proper heat transfer fluid (HTF) is a key factor to increase the efficiency of concentrated solar power plants and therefore, to reduce their internal associated CAPEX (capital expenditures of developing and constructing a plant, excluding any grid-connection charges) and OPEX (operating expenditures from the first year of a project's operation). This paper presents a comparative study of two commercial HTF which are widely used in different industries and CSP plants: thermal oil Therminol VP-1 and silicone fluid Syltherm 800. First, the authors theoretically studied the properties of both HTF based on the data given by the manufactures. Afterwards, the authors experimentally perform the comparison in a two-tank molten salt thermal energy storage pilot plant built at the University of Lleida (Spain). The study is focused on the plate heat exchanger of the facility during several charging processes with a counter flow arrangement. Results from both studies showed that, for the same working conditions, Therminol VP-1 is the best candidate for the above-mentioned purposes due to its higher heat transfer, lower thermal losses and lower power consumption associated to the HTF pump. However, it presents problems a low crystallization point, which should also be considered., The research leading to these results has received funding from Spanish goverment (Fondo tecnológico IDI-20090393, ConSOLida CENIT 2008-1005) and from Abengoa Solar NT. The work is partially funded by the Spanish government (ENE2008-06687-C02-01/CON, ENE2011-22722, ULLE10-4E-1305 and ENE2015-64117-C5-1-R (MINECO/FEDER)). The authors would like to thank the Catalan Government for the quality accreditation given to their research group GREA (2014 SGR 123). This project has also received funding from the European Commission Seventh Framework Programme (FP/2007-2013) under Grant agreement NºPIRSES-GA-2013-610692 (INNOSTORAGE) and from the European Union’s Horizon 2020 research and innovation programme under grant agreement No 657466 (INPATH-TES). Laia Miró would like to thank the Spanish Government for her research fellowship (BES-2012-051861). Jaume Gasia would like to thank the Departament d’Universitats, Recerca i Societat de la Informació de la Generalitat de Catalunya for his research fellowship (2017FI_B1 00092). The authors would like to thank Dr. Eduard Oró from Catalonia Institute for Energy Research (Spain) and Dr. Antoni Gil from Massachusetts Institute of Technology (USA) for their help during the initial stages of the experimentation.
Repositori Obert UdL
Publication Artículo científico (JournalArticle)

Thermal behaviour of D-mannitol when used as PCM: Comparison of results obtained by DSC and in a thermal energy storage unit at pilot plant scale

  • Gil, Antoni
  • Barreneche Güerisoli, Camila
  • Moreno Argilés, Pere
  • Solé Cutrona, Cristian
  • Fernández Renna, Ana Inés
  • Cabeza, Luisa F.
The use of thermal energy storage (TES) systems for solar heating and cooling applications has received considerable attention in recent decades because it has a high potential in energy savings. Phase change materials (PCMs) can store large amount of energy per mass unit compared with other TES materials. Nevertheless, the selection of the suitable PCM for each application is a key issue in any TES system design. The most important properties to take into account to select a PCM are the melting and solidification temperature, the phase change enthalpy and the stability after several thermal cycles. In this paper, D-mannitol was a candidate material to be tested as PCM in a solar cooling application due to its melting point (167 C) and a relatively high enthalpy (316.0 kJ/kg). The experiments performed by DSC have shown that the D-mannitol presents polymorphic structural changes and, therefore, its thermal properties are not always the same. Depending on the polymorphic phase obtained, D-mannitol has different melting temperature. This behaviour was corroborated in a storage tank, where it may be seen that the cooling rate of the D-mannitol is a key parameter in the formation of the different polymorphic phases., The work is partially funded by the Spanish government (ENE2011-22722). The authors would like to thank the Catalan Government for the quality accreditation given to their research group GREA (2009 SGR 534) and research group DIOPMA (2009 SGR 645). A. Gil would like to thank the Col·legi d’Enginyers Industrials de Catalunya for his research appointment.
Repositori Obert UdL
Publication Artículo científico (JournalArticle)

Unconventional experimental technologies available for phase change materials (PCM) characterization. Part 1. Thermophysical properties

  • Cabeza, Luisa F.
  • Barreneche Güerisoli, Camila
  • Martorell, Ingrid
  • Miró, Laia
  • Sari-Bey, Sana
  • Fois, Magali
  • Paksoy, Halime Ö.
  • Sahan, Nurten
  • Weber, Robert
  • Constantinescu, Mariaella
  • Anghel, Elena Maria
  • Malikova, Marta
  • Krupa, Igor
  • Delgado, Mónica
  • Dolado, Pablo
  • Furmanski, Piotr
  • Jaworski, Maciej
  • Haussmann, Thomas
  • Gschwander, Stefan
  • Fernández Renna, Ana Inés
The use of thermal energy storage by phase change materials (PCM) is increasing in interest for building applications. For the deployment of the technology, appropriate characterization of PCM and hybrid PCM is essential, but it is not always possible to carry it out with conventional equipment, mainly due to the sample size. This paper shows equipment developed in different research centers and universities to analyze thermophysical properties, such as specific heat, latent heat and melting temperature, and thermal conductivity and diffusivity of PCM and hybrid PCM materials., The work is partially funded by the European Union (COST Action COST TU0802), the Spanish government (ENE2011-28269-C03-01, ENE2011-28269-C03-02 and ENE2011- 22722), TUBITAK (project 110M032), and by Qatar National Foundation through the NPRP No.: 4-465-2-173. The authors would like to thank the Catalan Government for the quality accreditation given to the research group GREA (2009 SGR 534) and their research group DIOPMA (2009 SGR 645), both in Spain. Laia Miró would like to thank the Spanish Government for her research fellowship (BES-2012-051861).
Repositori Obert UdL
Publication Artículo científico (JournalArticle)

Phase change materials and thermal energy storage for buildings

  • Cabeza, Luisa F.
  • Gracia Cuesta, Alvaro de
It is well known that there is a need to develop technologies to achieve thermal comfort in buildings lowering the cooling and heating demand. Research has shown that thermal energy storage (TES) is a way to do so, but also other purposes can be pursued when using TES in buildings, such as peak shaving or increase of energy efficiency in HVAC systems. This paper reviews TES in buildings using sensible, latent heat and thermochemical energy storage. Sustainable heating and cooling with TES in buildings can be achieved through passive systems in building envelopes, Phase Change Materials (PCM) in active systems, sorption systems, and seasonal storage., The work partially funded by the Spanish government (ENE2011-22722 and ULLE10-4E-1305). The authors would like to thank the Catalan Government for the quality accreditation given to their research group (2014 SGR 123). The research leading to these results has received funding from the European Union’s Seventh Framework Programme (FP7/2007-2013) under grant agreement no. PIRSES-GA-2013-610692 (INNOSTORAGE). Alvaro de Gracia would like to thank Education Ministry of Chile for Grant PMI ANT1201.
Repositori Obert UdL
Publication Artículo científico (JournalArticle)

Two-tank molten salts thermal energy storage system for solar power plants at pilot plant scale: Lessons learnt and recommendations for its design, start-up and operation

  • Peiró Bell-lloch, Gerard
  • Prieto, Cristina
  • Gasia, Jaume
  • Jové, Aleix
  • Miró, Laia
  • Cabeza, Luisa F.
Renewable energies are main players to ensure the long-term energy supply. Solar power plants with thermal energy storage (TES) are one of the available renewable technologies which have more potential. Nowadays, there are still several aspects in the design and operation of these power plants which need to be improved, such as the correct operation of some specific instrumentation, the compatibility between TES materials and storage tanks materials, and operational process strategies. This paper presents the acquired experience during the design, start-up, and operation of a kWh scale pilot experimental facility built at the University of Lleida (Spain) together with Abengoa Research (Spain) in 2008. The versatility of this facility has allowed simulating real working conditions and therefore testing different TES systems, TES materials, solar power plant components, and operational strategies focused on TES for temperatures up to 400 °C. In the present paper, the authors show the lessons learnt at pilot and present the main problems and limitations encountered, and give advices of this experimental set-up to extrapolate the data to real plant, to provide solutions to technical problems and reduce the cost of commercial plants., The authors want to thank specially to Dr. Eduard Oró (today at Institut de Recerca d’Energies de Catalunya, Spain) and Dr. Antoni Gil (today at Massachusetts Institute of Technology, USA) for their help in the design, start-up and operation of the pilot plant facility. The research leading to these results has received funding from Spanish government through CDTI granted projects (Fondo tecnológico IDI-20090393, ConSOLida CENIT 2008-1005) and from Abengoa Solar NT. The work is partially funded by the Spanish government (ENE2008-06687-C02-01/CON, ENE2011-22722, ULLE10-4E-1305, and ENE2015-64117-C5-1-R (MINECO/FEDER)). The authors would like to thank the Catalan Government for the quality accreditation given to their research group GREA (2014 SGR 123). GREA is a certified agent TECNIO in the category of technology developers from the Government of Catalonia. This project has received funding from the European Commission Seventh Framework Programme (FP/2007-2013) under Grant agreement NºPIRSES-GA-2013-610692 (INNOSTORAGE) and from the European Union’s Horizon 2020 research and innovation programme under grant agreement No 657466 (INPATH-TES). Laia Miró would like to thank the Spanish Government for her research fellowship (BES-2012-051861). Jaume Gasia would like to thank the Departament d'Universitats, Recerca i Societat de la Informació de la Generalitat de Catalunya for his research fellowship (2017FI_B1 00092).
Repositori Obert UdL
Publication Artículo científico (JournalArticle)

Thermal storage in a MW scale. Molten salt solar thermal pilot facility: Plant description and commissioning experiences

  • Prieto, Cristina
  • Osuna, Rafael
  • Fernández Renna, Ana Inés
  • Cabeza, Luisa F.
In 2008, following its R&D strategy roadmap for Concentrated Solar Power, Abengoa designed, built and tested a unique Molten Salts pilot plant at the representative scale of 8 MWhth, coupled with a trough oil loop. The objectives of this project were based on evaluating the technology at a scale at which the results are sufficiently representative of the real circumstances facing a commercial plant that utilizes this storage technology. To this end, the MS-TES plant was brought into operation on January 19th, 2009, been the first demo plant of indirect double tank storage in operation in the world. Key points such a material corrosion, analysis of possible leakage points, calculation of performance or true efficiency of the storage (including a thorough assessment of thermal losses) and analysis of plant operation are the lines that have been analysed at this plant. Operational aspects such as the mechanical assembling, the pre-heating, the filling up and plant performance were deeply addressed. Key components as the storage tanks, the heat exchanger, the molten salts pumps, the heat-tracing systems or valves and instrumentation were tested. In this first paper, the description and commissioning of the plant is presented together a set of lessons learnt to be applied at the commercial plant scale., The research leading to these results has received funding from Spanish government (Fondo tecnológico IDI-20090393, ConSOLida CENIT2008-1005). The work is partially funded by the Spanish government (ENE2008-06687-C02-01, ENE2011-28269-C03-02, ENE2011-22722). The authors would like to thank the Catalan Government for the quality accreditation given to their research group GREA (2014 SGR 123) and research group DIOPMA (2014 SGR 1543).
Repositori Obert UdL
Publication Artículo científico (JournalArticle)

Physico-chemical and mechanical properties of microencapsulated phase change material

  • Giro-Paloma, Jessica
  • Oncins, Gerard
  • Barreneche Güerisoli, Camila
  • Martínez, Mònica
  • Fernández Renna, Ana Inés
  • Cabeza, Luisa F.
Microencapsulated phase change materials (MPCM) are well known in advanced technologies for the utilization in active and passive systems, which have the capacity to absorb and slowly release the latent heat involved in a phase change process. Microcapsules consist of little containers, which are made of polymer on the outside, and paraffin wax as PCM in the inside. The use of microencapsulated PCM has many advantages as microcapsules can handle phase change materials as core allowing the preparation of slurries. However there are some concerns about cycling of MPCM slurries because of the breakage of microcapsules during charging/discharging and the subsequent loss of effectiveness. This phenomenon motivates the study of the mechanical response when a force is applied to the microcapsule. The maximum force that Micronal® DS 5001 can afford before breaking was determined by Atomic Force Microscopy (AFM). To simulate real conditions in service, assays were done at different temperatures: with the PCM in solid state at 25 ºC, and with the PCM melted at 45 ºC and 80 ºC. To better understand the behavior of these materials, Micronal® DS 5001 microcapsules were characterized using different physic-chemical techniques. Microcapsules Fourier Transform Infrared Spectroscopy (FT-IR) results showed the main vibrations corresponding to acrylic groups of the outside polymer. Thermal stability was studied by Thermogravimetrical Analysis (TGA), and X-ray Fluorescence (XRF) was used to characterize the resulting inorganic residue. The thermal properties were determined using Differential Scanning Calorimetry (DSC) curves. Particles morphology was studied with Scanning Electron Microscopy (SEM) and Mie method was used to evaluate the particle size distribution. Samples had a bimodal distribution of size and were formed by two different particles sizes: agglomerates of 150 lm diameter formed by small particles of 6 lm. Atomic Force Microscopy in nanoindentation mode was used to evaluate the elastic response of the particles at different temperatures. Different values of effective modulus Eeff were calculated for agglomerates and small particles. It was observed that stiffness depended on the temperature assay and particle size, as agglomerates showed higher stiffness than small particles, which showed an important decrease in elastic properties at 80 ºC., The work is partially funded by the Spanish government (ENE2011-28269-C03-02 and ENE2011-22722) and the European Union (COST Action TU0802). The authors would like to thank the Catalan Government for the quality accreditation given to their research group GREA (2009 SGR 534) and research group DIOPMA (2009 SGR 645).
Repositori Obert UdL
Publication Artículo científico (JournalArticle)

Review on system and materials requirements for high temperature thermal energy storage. Part 1: General requirements

  • Gasia, Jaume
  • Miró, Laia
  • Cabeza, Luisa F.
High temperature thermal energy storage offers a huge energy saving potential in industrial applications such as solar energy, automotive, heating and cooling, and industrial waste heat recovery. However, certain requirements need to be faced in order to ensure an optimal performance, and to further achieve widespread deployment. In the present review, these requirements are identified for high temperature (>150 °C) thermal energy storage systems and materials (both sensible and latent), and the scientific studies carried out meeting them are reviewed. Currently, there is a lack of data in the literature analysing thermal energy storage from both the systems and materials point of view. In the part 1 of this review more than 25 requirements have been found and classified into chemical, kinetic, physical and thermal (from the material point of view), and environmental, economic and technologic (form both the material and system point of view). The enhancements focused on the thermal conductivity are addressed in the Part 2 of this review due to their research significance and extension., The work is partially funded by the Spanish government (ENE2015-64117-C5-1-R, ENE2011-22722 and ULLE10-4E-1305). The authors would like to thank the Catalan Government for the quality accreditation given to their research group GREA (2014 SGR 123). This project has received funding from the European Commission Seventh Framework Programme (FP/2007-2013) under Grant agreement No. PIRSES-GA-2013-610692 (INNOSTORAGE) and from the European Union's Horizon 2020 research and innovation programme under grant agreement No. 657466 (INPATH-TES). Laia Miró would like to thank the Spanish Government for her research fellowship (BES-2012-051861). Jaume Gasia would like to thank the Departament d'Universitats, Recerca i Societat de la Informació de la Generalitat de Catalunya for his research fellowship (2016FI_B 00047).
Repositori Obert UdL
Publication Artículo científico (JournalArticle)

Experimental analysis of charging and discharging processes, with parallel and counter flow arrangements, in a molten salts high temperature pilot plant scale setup

  • Peiró Bell-lloch, Gerard
  • Gasia, Jaume
  • Miró, Laia
  • Prieto, Cristina
  • Cabeza, Luisa F.
Despite the fact that there are some commercial concentrated solar power plants worldwide, there is currently a lack of experimental reports about the operational characteristics of this type of plants. Therefore, a two-tank molten salts thermal energy storage (TES) pilot plant at the University of Lleida (Spain) was used to analyze charging and discharging processes under real conditions. In this facility, 1000 kg of molten salts are used as TES material and Therminol VP-1 is used as heat transfer fluid (HTF). This facility is equipped with measurement equipment which allows an exhaustive analysis of the processes. In this study, the fact of varying the flow arrangement in the heat exchanger (parallel and counter flow arrangements) and the temperature difference between the molten salts and the HTF have been studied and discussed in terms of temperature profiles, energy and power stored/released from/to both HTF and molten salts, efficiencies and effectiveness. The best working conditions found were counter flow arrangement with a temperature grading of about 65 °C., The research leading to these results has received funding from Spanish government (Fondo tecnológico IDI-20090393, ConSOLida CENIT 2008-1005) and from Abengoa Solar NT. The work is partially funded by the Spanish government (ENE2008-06687-C02-01/CON, ENE2011-28269-C03-02, ENE2011-22722 and ULLE10-4E-1305). The authors would like to thank the Catalan Government for the quality accreditation given to their research group GREA (2014 SGR 123). This project has also received funding from the European Commission Seventh Framework Programme (FP/2007-2013) under Grant agreement N°PIRSES-GA-2013-610692 (INNOSTORAGE) and from the European Union’s Horizon 2020 research and innovation programme under grant agreement No 657466 (INPATH-TES). Laia Miró would like to thank the Spanish Government for her research fellowship (BES-2012-051861). Jaume Gasia would like to thank the Departament d’Universitats, Recerca i Societat de la Informació de la Generalitat de Catalunya for his research fellowship (2016FI_B 00047).
Repositori Obert UdL
Publication Artículo científico (JournalArticle)

Industrial waste materials and by-products as thermal energy storage (TES) materials: A review

  • Gutierrez, Andrea
  • Miró, Laia
  • Gil, Antoni
  • Rodríguez Aseguinolaza, Javier
  • Barreneche Güerisoli, Camila
  • Calvet, Nicolas
  • Py, Xavier
  • Fernández Renna, Ana Inés
  • Grágeda, Mario
  • Ushak, Svetlana
  • Cabeza, Luisa F.
A wide variety of potential materials for thermal energy storage (TES) have been identify depending on the implemented TES method, Sensible, latent or thermochemical. In order to improve the efficiency of TES systems more alternatives are continuously being sought. In this regard, this paper presents the review of low cost heat storage materials focused mainly in two objectives: on the one hand, the implementation of improved heat storage devices based on new appropriate materials and, on the other hand, the valorisation of waste industrial materials will have strong environmental, economic and societal benefits such as reducing the landfilled waste amounts, reducing the greenhouse emissions and others. Different industrial and municipal waste materials and by products have been considered as potential TES materials and have been characterized as such. Asbestos containing wastes, fly ashes, by-products from the salt industry and from the metal industry, wastes from recycling steel process and from copper refining process and dross from the aluminium industry, and municipal wastes (glass and nylon) have been considered. This work shows a great revalorization of wastes and by-product opportunity as TES materials, although more studies are needed to achieve industrial deployment of the idea., The work is partially funded by the Spanish government (ENE2011-28269-C03-02, ENE2011-22722 and ULLE10-4E-1305). The authors would like to thank the Catalan Government for the quality accreditation given to their research group GREA (2014 SGR 123) and research group DIOPMA (2014 SGR 1543). The research leading to these results has received funding from the European Union's Seventh Framework Programme (FP7/2007-2013) under grant agreement n° PIRSES-GA-2013-610692 (INNOSTORAGE). Laia Miró would like to thank the Spanish Government for her research fellowship (BES-2012-051861). The work at CIC Energigune was supported by the Department of Industry, Innovation, Commerce and Tourism of the Basque Country government through the ETORTEK CIC Energigune-2013 research program. Research at Masdar Institute is supported by the Government of Abu Dhabi to help fulfill the vision of the late President Sheikh Zayed bin Sultan Al Nayhan for sustainable development and empowerment of the UAE and humankind. Researchers of PROMES address all their gratitude to the French government for the funding of their work through the ANR SESCO and SACRE projects within the ANR SEED program. They also acknowledge the support of the CNRS, the University of Perpignan Via Domitia and the EUROPLASMA/INERTAM Company. The work at the University of Antofagasta was supported by CONICYT/FONDAP Nº 15110019, and the Education Ministry of Chile Grant PMI ANT 1201. Andrea Gutierrez would like to acknowledge to the Education Ministry of Chile her doctorate scholarship ANT 1106 and CONICYT/PAI N°7813110010.
Repositori Obert UdL
Publication Artículo científico (JournalArticle)

Thermal energy storage (TES) for industrial waste heat (IWH) recovery: a review

  • Miró, Laia
  • Gasia, Jaume
  • Cabeza, Luisa F.
Industrial activities have a huge potential for waste heat recovery. In spite of its high potential, industrial waste heat (IWH) is currently underutilized. This may be due, on one hand, to the technical and economic difficulties in applying conventional heat recovery methods and, on the other, the temporary or geographical mismatch between the energy released and its heat demand. Thermal energy storage (TES) is a technology which can solve the existing mismatch by recovering the IWH and storing it for a later use. Moreover, the use of recovered IWH leads to a decrease of CO2 emissions and to economic and energy savings. Depending on the distance between the IWH source and the heat demand, TES systems can be placed on-site or the IWH can be transported by means of mobile TES systems, to an off-site heat demand. Around 50 industry case studies, in which both on-site and off-site recovery systems are considered are here reviewed and discussed taking into account the characteristics of the heat source, the heat, the TES system, and the economic, environmental and energy savings. Besides, the trends and the maturity of the cases reviewed have been considered. On-site TES systems in the basic metals manufacturing are the technology and industrial sector which has focused the most attention among the researchers, respectively. Moreover, water (or steam), erythritol and zeolite are the TES materials used in most industries and space comfort and electricity generation are the most recurrent applications., The work is partially funded by the Spanish government (ENE2011-22722, ENE2015-64117-C5-1-R (MINECO/FEDER)). This project has received funding from the European Commission Seventh Framework Programme (FP/2007-2013) under Grant agreement No. PIRSES-GA-2013-610692 (INNOSTORAGE) and from the European Union’s Horizon 2020 research and innovation programme under grant agreement No. 657466 (INPATH-TES). The authors would like to thank the Catalan Government for the quality accreditation given to their research group GREA (2014 SGR 123). Jaume Gasia would like to thank the Departament d’Universitats, Recerca i Societat de la Informació de la Generalitat de Catalunya for his research fellowship (2016FI_B 00047). Laia Miró would like to thank the Spanish Government for her research fellowship (BES-2012-051861).
Repositori Obert UdL
Publication Artículo científico (JournalArticle)

Corrosion of metals and salt hydrates used for thermochemical energy storage

  • Solé, Aran
  • Miró, Laia
  • Barreneche Güerisoli, Camila
  • Martorell, Ingrid
  • Cabeza, Luisa F.
Solar energy can be efficiently used if thermal energy storage systems are accordingly designed to match availability and demand. Thermal energy storage by thermochemical materials (TCM) is very attractive since these materials present a high storage density. Therefore, compact systems can be designed to provide both heating and cooling in dwellings. One of the main drawbacks of the TCM is corrosion with metals in contact. Hence, the objective of this study is to present the obtained results of an immersion corrosion test following ASTM G1 simulating an open TCM reactor, under humidity and temperature defined conditions. Four common metals: copper, aluminum, stainless steel 316, and carbon steel, and five TCM: CaCl2, Na2S, CaO, MgSO4, and MgCl2, were studied. Aluminum and copper show severe corrosion when combined with Na2S, aluminum corrosion is more significant since the specimen was totally destroyed after 3 weeks. Stainless steel 316 is recommended to be used as a metal container material when storing all tested TCM., The research leading to these results has received funding from the European Commission Seventh Framework Programme (FP/2007-2013) under grant agreement no ENER/FP7/295983 (MERITS). Aran Solé would like to thank the Departament d'Universitats, Recerca i Societat de la Informació de la Generalitat de Catalunya for her research fellowship. Laia Miró would like to thank the Spanish Government for her training researcher personal fellowship (BES-2012-051861). The work is partially funded by the Spanish Government (ENE2011-28269-C03-02 and ENE2011-22722). The authors would like to thank the Catalan Government for the quality accreditation given to the research group GREA (2014 SGR 123).
Repositori Obert UdL
Publication Artículo científico (JournalArticle)

Thermophysical characterization of sorption TCM

  • Barreneche Güerisoli, Camila
  • Fernández Renna, Ana Inés
  • Cabeza, Luisa F.
  • Cuypers, Ruud
Thermochemical materials (TCM) are proposed for thermal energy storage as one of the future options to achieve lower energy consumption in buildings and other industrial applications, as well as to store energy from solar energy. In this study, the thermophysical properties of two TCM, CaCl2 and zeolite, are determined with TGA and DSC and samples are cycled 4 times with TGA. Results show that the material with the highest energy density is the salt, CaCl2. Moreover, both materials under study present noble cyclability., The work is partially funded by the Spanish government (ENE2011-28269-C03-02 and ENE2011-22722). The authors would like to thank the Catalan Government for the quality accreditation given to their research group GREA (2009 SGR 534) and research group DIOPMA (2009 SGR 645). Furthermore, the work was partially funded by European Union (Cost Action TU0802).
Repositori Obert UdL
Publication Artículo científico (JournalArticle)

Physicochemical and thermal study of a MPCM of PMMA shell and paraffin wax as a core

  • Giro-Paloma, Jessica
  • Barreneche Güerisoli, Camila
  • Delgado, Mónica
  • Martínez, Mònica
  • Fernández Renna, Ana Inés
  • Cabeza, Luisa F.
The present work studies a Phase Change Slurry (PCS) as a proposed Thermal Energy Storage (TES) medium. Microencapsulation is an advanced technology to implement PCMs (Phase Change Material) avoiding leakage from building materials. The morphology and physicochemical properties of this Microencapsulated Phase Change Material (MPCM) sample were analyzed using some analytical techniques like Scanning Electron Microscopy (SEM), Infrared Spectroscopy (FT-IR), Thermogravimetrical Analysis (TGA), Differential Scanning Calorimeter (DSC), and Atomic Force Microscopy (AFM). The results showed that Micronal® DS 5007 is a suitable candidate to be used as slurry in active systems due to their studied mechanical properties., The work is partially funded by the Spanish government (ENE2011-28269-C03-02, ENE2011-22722, and ENE2011-28269-C03-01). The authors would like to thank the Catalan Government for the quality accreditation given to their research group GREA (2009 SGR 534) and research group DIOPMA (2009 SGR 645).
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Physicochemical and thermal study of a MPCM of PMMA shell and paraffin wax as a core

  • Giro-Paloma, J.
  • Barreneche, C.
  • Delgado, M.
  • Martínez, M.
  • Fernández, A.I.
  • Cabeza, L.F.
The present work studies a Phase Change Slurry (PCS) as a proposed Thermal Energy Storage (TES) medium. Microencapsulation is an advanced technology to implement PCMs (Phase Change Material) avoiding leakage from building materials. The morphology and physicochemical properties of this Microencapsulated Phase Change Material (MPCM) sample were analyzed using some analytical techniques like Scanning Electron Microscopy (SEM), Infrared Spectroscopy (FT-IR), Thermogravimetrical Analysis (TGA), Differential Scanning Calorimeter (DSC), and Atomic Force Microscopy (AFM). The results showed that Micronal® DS 5007 is a suitable candidate to be used as slurry in active systems due to their studied mechanical properties.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

A theoretical study on the accuracy of the T-history method for enthalpy-temperature curve measurement: Analysis of the influence of thermal gradients inside T-history samples

  • Mazo, J.
  • Delgado, M.
  • Lázaro, A.
  • Dolado, P.
  • Peñalosa, C.
  • Marín, J.M.
  • Zalba, B.
The present work analyses the effect of radial thermal gradients inside T-history samples on the enthalpy temperature curve measurement. A conduction heat transfer model has been utilized for this purpose. Some expressions have been obtained that relate the main dimensionless numbers of the experiments with the deviations in specific heat capacity, phase change enthalpy and phase change temperature estimations. Although these relations can only be strictly applied to solid materials (e.g. measurements of shape stabilized phase change materials), they can provide some useful and conservative bounds for the deviations of the T-history method. Biot numbers emerge as the most relevant dimensionless parameters in the accuracy of the specific heat capacity and phase change enthalpy estimation whereas this model predicts a negligible influence of the temperature levels used for the experiments or the Stefan number.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Evaluation of the suitability of different calorimetric methods to determine the enthalpy-temperature curve of granular PCM composites

  • Mazo, Javier
  • Delgado, Mónica
  • Peñalosa, Conchita
  • Dolado, Pablo
  • Miranda, Inés
  • Lázaro, Ana
  • Marín, José María
  • Zalba, Belén
The present research has analyzed the complementarity of different measuring methodologies when characterizing the phase changing behaviour of a granular PCM composite (GPCC) through a comparison of their results. Specifically, the enthalpy variation of the GR31 product manufactured by Rubitherm has been measured by using: (1) An energy balance calculation of an air stream flowing through a GPCC packed bed; (2) Differential Scanning Calorimetry; (3) the T-history method. The main purpose of this study was to evaluate the suitability of these methods for the enthalpy-temperature curve determination of GPCC. The energy balance setup gave an accurate measurement of the enthalpy variation within a sufficiently high temperature interval. Obtaining a representative sample was not a problem using this method, in contrast to the DSC which requires a greater number of tests to obtain an average value representative of the packed bed. However, the energy balance method does not enable the direct determination of the enthalpy-temperature curve. The T-history methodology allows the enthalpy to be determined based on temperature while the representativeness problem of the DSC is avoided due to the higher sample volume. Nevertheless, the sample must be altered, crushed and subsequently compacted to reduce the effects of the thermal resistances provoked by the void spaces being filled by air. This comparison has shown that there is no single valid methodology for characterizing the phase changing behaviour of PCM granules.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Experimental analysis of the influence of microcapsule mass fraction on the thermal and rheological behavior of a PCM slurry

  • Delgado,M.
  • Lázaro,A.
  • Peñalosa,C.
  • Zalba,B .
A microencapsulated PCM (Phase Change Material) slurry with three different PCM mass fractions (14, 20 and 30%) has been analyzed. The present study investigates the influence of the PCM microcapsule mass fraction on the thermal and rheological characterization. Specifically, the EnthalpyeTemperature curves, the Thermal ConductivityeTemperature curves and the ViscosityeShear rate curves have been determined In addition, the physical stability under thermo-mechanical cycles has also been studied, as well as the heat transfer phenomenon and the fluid mechanics. The results have shown an enhancement in the heat transfer phenomenon, the slurry with 20% PCM microcapsules being the best option for use as a heat transfer fluid. Rupture of the PCM microcapsules was only observed for the slurry with 30% PCM microcapsules, after being pumped during three weeks and having experienced 10,000 solidification emelting cycles.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Unconventional experimental technologies available for phase change materials (PCM) characterization. Part 1. Thermophysical properties

  • Cabeza, L. F.
  • Barreneche, C.
  • Martorell, I.
  • Miró, L.
  • Sari-Bey, S.
  • Fois, M.
  • Paksoy, H. O.
  • Sahan, N.
  • Weber, R.
  • Constantinescu, M.
  • Anghel, E. M.
  • Malikova, M.
  • Krupa, I.
  • Delgado, M.
  • Dolado, P.
  • Furmanski, P.
  • Jaworski, M.
  • Haussmann, T.
  • Gschwander, S.
  • Fernández, A. I.
The use of thermal energy storage by phase change materials (PCM) is increasing in interest for building applications. For the deployment of the technology, appropriate characterization of PCM and hybrid PCM is essential, but it is not always possible to carry it out with conventional equipment, mainly due to the sample size. This paper shows equipment developed in different research centers and universities to analyze thermophysical properties, such as specific heat, latent heat and melting temperature, and thermal conductivity and diffusivity of PCM and hybrid PCM materials
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Review of technology: Thermochemical energy storage for concentrated solar power plants

  • Prieto, Cristina
  • Cooper, Patrick
  • Fernández Renna, Ana Inés
  • Cabeza, Luisa F.
To be able to extend the operation of a solar power plant (CSP) up to 15 h, thermal energy storage (TES) is necessary. But TES also provides more versatility to the plant and makes its reliance during operation hours more dependable. On the other hand, due to the different CSP configurations, a broad spectrum of storage technologies, materials and methods is needed. Sensible and latent heat storage are known technologies in CSP, but thermochemical storage (TCS) is still very much at laboratory level. Nevertheless, TCS has de advantage of nearly no losses during storage and very good volumetric energy density. This review summarizes and compares the different TCS that are today being investigated. Those systems are based in three redox reactions, sulfur-based cycles, metal oxide reduction–oxidation cycles, and perovskite-type hydrogen production, and metal oxide non-redox cycles due to their similarity. This review shows that all these cycles are promising, but none of them seems to have all the characteristics necessary to become the only one storage system for CSP. The main conclusion of the review is that the calcium carbonate is the cycle with most experimentation behind it to infer that it could be viable and should thus be attempted at a research plant scale once a reactivation cycle can be designed; and the manganese oxide cycle, while less developed, is fundamental enough to be a suitable application for desert climates over the rest of the water-frugal or even water-avoiding cycles., The work was partially funded by the Spanish government (project ENE2011−22722). The authors would also like to thank the Catalan Government for the quality accreditation given to their research group GREA (2014 SGR 123) and DIOPMA (2014 SGR 1543). The research leading to these results has received funding from the European Union׳s Seventh Framework Programme (FP7/2007−2013) under Grant agreement n° PIRSES-GA−2013−610692 (INNOSTORAGE).
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Unconventional experimental technologies available for phase change materials (PCM) characterization. Part 1. Thermophysical properties

  • Cabeza, Luisa F.
  • Barreneche Güerisoli, Camila
  • Martorell, Ingrid
  • Miró, Laia
  • Sari-Bey, Sana
  • Fois, Magali
  • Paksoy, Halime Ö.
  • Sahan, Nurten
  • Weber, Robert
  • Constantinescu, Mariaella
  • Anghel, Elena Maria
  • Malikova, Marta
  • Krupa, Igor
  • Delgado, Mónica
  • Dolado, Pablo
  • Furmanski, Piotr
  • Jaworski, Maciej
  • Haussmann, Thomas
  • Gschwander, Stefan
  • Fernández Renna, Ana Inés
The use of thermal energy storage by phase change materials (PCM) is increasing in interest for building applications. For the deployment of the technology, appropriate characterization of PCM and hybrid PCM is essential, but it is not always possible to carry it out with conventional equipment, mainly due to the sample size. This paper shows equipment developed in different research centers and universities to analyze thermophysical properties, such as specific heat, latent heat and melting temperature, and thermal conductivity and diffusivity of PCM and hybrid PCM materials., The work is partially funded by the European Union (COST Action COST TU0802), the Spanish government (ENE2011-28269-C03-01, ENE2011-28269-C03-02 and ENE2011- 22722), TUBITAK (project 110M032), and by Qatar National Foundation through the NPRP No.: 4-465-2-173. The authors would like to thank the Catalan Government for the quality accreditation given to the research group GREA (2009 SGR 534) and their research group DIOPMA (2009 SGR 645), both in Spain. Laia Miró would like to thank the Spanish Government for her research fellowship (BES-2012-051861).
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Types, methods, techniques, and applications for microencapsulated phase change materials (MPCM): a review

  • Giro-Paloma, Jessica
  • Martínez, Mònica
  • Cabeza, Luisa F.
  • Fernández Renna, Ana Inés
Phase change materials (PCM) can be employed in many fields because of their capacity to absorb and release energy when it is necessary. Nowadays, the number of studies about these materials is increasing because of their benefits in energy systems. This paper reviews the previous researches and developments on microencapsulated phase change materials (MPCM) in thermal energy storage (TES) systems, focusing on the different methods of encapsulations and also the different applications of these materials. This review aims to be a useful guide for the researchers in this area, because it explains the different types of phase change core materials, the different shells, the methods to microencapsulate these PCM, the most used techniques to characterize these microencapsulated phase change materials, and a revision of the main applications., The work is partially funded by the Spanish government (ENE2011-28269-C03-02 and ENE2011-22722). The authors would like to thank the Catalan Government for the quality accreditation given to their research group GREA (2014 SGR 123) and research group DIOPMA (2014 SGR 1543). The research leading to these results has received funding from the European Union's Seventh Framework Programme (FP7/2007–2013) under Grant agreement no. PIRSES-GA-2013-610692 (INNOSTORAGE).
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

The use of phase change materials in fish farms: a general analysis

  • Zsembinszki, Gabriel
  • Solé Cutrona, Cristian
  • Castell, Albert
  • Pérez Luque, Gabriel
  • Cabeza, Luisa F.
Aquaculture has become an important sector of animal food production thanks to a fast and continuous growth over the last few decades. Both marine and fresh water fish can be reared in fish farms, and there are species that are mainly produced by aquaculture rather than capture. As most of the reared fish species are sensible to water temperature and its fluctuations, having the control of this parameter in fish farms becomes an important issue that has to be taken into account. In this paper, three different fish farms are studied by simulating the water temperature when a thermal energy storage (TES) system using phase change materials (PCMs) is implemented. The effect and the estimated amounts of PCM required in each particular case are also analyzed. The results show that appreciable effects can be obtained, especially when the TES unit is used in combination with auxiliary sources of energy, such as solar collectors., The work was partially funded by the Spanish Government (ENE2011-22722). The authors would like to thank the Catalan Government for the quality accreditation given to their research group (2009 SGR 534).
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Thermophysical characterization of sorption TCM

  • Barreneche Güerisoli, Camila
  • Fernández Renna, Ana Inés
  • Cabeza, Luisa F.
  • Cuypers, Ruud
Thermochemical materials (TCM) are proposed for thermal energy storage as one of the future options to achieve lower energy consumption in buildings and other industrial applications, as well as to store energy from solar energy. In this study, the thermophysical properties of two TCM, CaCl2 and zeolite, are determined with TGA and DSC and samples are cycled 4 times with TGA. Results show that the material with the highest energy density is the salt, CaCl2. Moreover, both materials under study present noble cyclability., The work is partially funded by the Spanish government (ENE2011-28269-C03-02 and ENE2011-22722). The authors would like to thank the Catalan Government for the quality accreditation given to their research group GREA (2009 SGR 534) and research group DIOPMA (2009 SGR 645). Furthermore, the work was partially funded by European Union (Cost Action TU0802).
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Methodologies to estimate industrial waste heat potential by transferring key figures: a case study for Spain

  • Miró, Laia
  • Brueckner, Sarah
  • McKenna, Russell
  • Cabeza, Luisa F.
In the current European energy context, the use of recovered industrial waste heat provides an attractive opportunity to substitute primary energy consumption by a low-emission and low-cost energy carrier. In the case of industrial waste heat, this potential is currently not only largely untapped, but also unaccounted for. In order to achieve a widespread use of recovered industrial waste heat, assessments with a large scope and high spatial resolution are needed. Three methods published in the period 2002–2010 have been found in the literature, which are potentially transferable to other regions. These three methods are based on either the energy consumption of each manufacturing sector or the individual site CO2 emissions. The scope of this analysis is, first, to investigate in how far a transfer of the figures to different countries or regions is sensible in comparison to former studies in the literature. In the process, some uncertainties when transferring methods were identified (different definitions of industry, different standard industrial activities classifications or no standard at all, etc.). The second goal is, once the methodology is accepted, to apply it to a case study, in this case the industrial sector in Spain and two of its counties (Catalonia and the Basque Country) for the years 2001, 2009, 2010 and 2013. In this period, and based on the different approaches employed, the Spanish annual industrial waste heat potential ranges from 54.3 to 151.1 PJ, Catalonia from 8.6 to 29.7 PJ, and from 7.2 to 11.9 PJ for the Basque Country. The methods are considered highly transferable but uncertainties inevitably arise in the case that the source and destination industrial sectors are very different., The work is partially funded by the Spanish government (ENE2011-22722 and ULLE10-4E-1305) and by BMWi Federal Ministry for Economic Affairs and Energy in Germany (Project FKZ 0327383B Mobile Sorption Heat Storage). The authors would like to thank the Catalan Government for the quality accreditation given to their research group GREA (2014 SGR 123). This project has received funding from the European Commission Seventh Framework Programme (FP/2007-2013) under Grant agreement N°PIRSES-GA-2013-610692 (INNOSTORAGE) and from the European Union’s Horizon 2020 research and innovation programme under grant agreement No. 657466 (INPATH-TES). Laia Miró would like to thank the Spanish Government for her research fellowship (BES-2012-051861).
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

A correlation of the convective heat transfer coefficient between an air flow and a phase change material plate

  • Gracia Cuesta, Alvaro de
  • David, Damien
  • Castell, Albert
  • Cabeza, Luisa F.
  • Virgone, Joseph
This paper provides a new correlation to determine the heat transfer coefficient between an air flow and a plate made of phase change material (PCM). This correlation was built for the simulation of heat storage units containing PCM plates subjected to an inlet temperature step. The presented correlation has the following form: NuPCM x;t ¼ NuPSM$f PCM. The first term NuPSM is for a plate made of traditional material. The term fPCM is a perturbation due to the phase change in the plate. Each term depends on 5 non-dimensional parameters. One of them represents the advance in the total heating or cooling process, in order to take into account the transient evolution of the convective coefficient. The correlations are built using the Least Squares Method, from series of CDF simulation data. The shape of the perturbation fPCM reveals a complex evolution of the temperature repartition in the PCM plate. Finally, a nodal model of the plate has been developed in order to test the provided new correlation and other correlations available in the literature. The results obtained with the present correlation show better agreements with the CFD results, which make this correlation suitable for the simulation of PCM heat storage systems., This work was supported by the “Corporación Tecnológica de Andalucía” by means of the project “MECLIDE-Soluciones estructurales con materiales especiales para la climatización diferida de edificios” with the collaboration of DETEA. The work was partially funded by the Spanish Government (ENE2011-22722 and ULLE10-4E-1305) and the European Union (COST Action COST TU0802). The authors would like to thank the Catalan Government for the quality accreditation given to their research group (2009 SGR 534).
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Embodied energy in thermal energy storage (TES) systems for high temperature applications

  • Miró, Laia
  • Oró Prim, Eduard
  • Boer, Dieter
  • Cabeza, Luisa F.
Currently, there is an increasing interest in concentrated solar power (CSP) plants as alternative to produce renewable electricity at large scale by using mirrors to concentrate the solar energy and to convert it into high temperature heat. These facilities can be combined with thermal energy storage (TES) systems, which are, nowadays, one of the most feasible solutions in facing the challenge of the intermittent energy supply and demand. However, they are still in research process and, for that, there is a lack of environmental impact studies of these TES systems complementing solar plants. This paper accounts the environmental impact of three TES systems used nowadays in high temperature applications for CSP plants: first, a system which stores sensible heat in high temperature concrete; second, a system storing sensible heat in molten salts; and third, another system with molten salts but storing latent heat. All the systems are normalised in order to be comparable between them due to its initial storage capacity difference. The environmental impact is accounted by calculating the amount of embodied energy in the components of the different TES systems. Notice that embodied energy refers to the total energy inputs required to make a component. Between the three systems, the sensible heat system using concrete as storage material is the one with less environmental impact while the molten salts and PCM have a higher value of embodied energy, mainly due to the nitrate mixture used as storage material. Finally, advantages and disadvantages of the method proposed used are discussed, The work was partially funded by the Spanish government (project ENE2011-22722). The authors would like to thank the Catalan Government for the quality accreditation given to their research group GREA (2009 SGR 534). The research leading to these results has received funding from the European Union’s Seventh Framework Programme (FP7/2007-2013) under Grant agreement n PIRSES-GA-2013-610692 (INNOSTORAGE). Eduard Oró would like to thank the University of Lleida for his research fellowship. Laia Miró would like to thank the Spanish Government for her research fellowship (BES-2012-051861).
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Thermomechanical testing under operating conditions of A516Gr70 used for CSP storage tanks

  • Prieto, Cristina
  • Barreneche Güerisoli, Camila
  • Martínez, Mònica
  • Cabeza, Luisa F.
  • Fernández Renna, Ana Inés
Thermal energy storage (TES) in molten salts is the storage dominating technology in solar power applications today. In two-tank molten salt storage systems energy density ranges from 30 to 70 kW h/m3 are achievable. The salt material used is a binary system, composed of 60% NaNO3 and 40% KNO3. In the 8 MWhth pilot plant built and tested by Abengoa, the storage tanks were made of steel A516Gr.70 using the Appendix M of code API 650 for their design. A specific testing device was developed to evaluate thermo-mechanical properties, and a study was conducted in order to evaluate tensile properties of A516Gr.70 specimens under operation conditions for the hot tank at the pilot plant that is in contact with molten salts at 380 °C. Results confirmed the outcomes of the work: the reduction of the yield limit, elongation before fracture, and Young modulus at 380 °C after having been 5 min immersed in molten salts. Moreover, after a creep-test simulating operating 7 days conditions during, an additional reduction of the yield limit was measured., The research leading to these results has received funding from Spanish government (Fondo tecnológico IDI-20090393, ConSOLida CENIT 2008-1005). The work is partially funded by the Spanish government (ENE2011-28269-C03-02, ENE2011-22722, ENE2015-64117-C5-1-R, and ENE2015-64117-C5-2-R). The research leading to these results has received funding from the European Union's Seventh Framework Programme (FP7/2007-2013) under grant agreement n° PIRSES-GA-2013-610692 (INNOSTORAGE) and from the European Union’s Horizon 2020 research and innovation programme under grant agreement No 657466 (INPATH-TES). The authors would like to thank the Catalan Government for the quality accreditation given to their research groups GREA (2014 SGR 123) and research group DIOPMA (2014 SGR 1543). Dr. Camila Barreneche would like to thank Ministerio de Economía y Competitividad de España for Grant Juan de la Cierva FJCI-2014-22886.
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Experimental analysis of charging and discharging processes, with parallel and counter flow arrangements, in a molten salts high temperature pilot plant scale setup

  • Peiró Bell-lloch, Gerard
  • Gasia, Jaume
  • Miró, Laia
  • Prieto, Cristina
  • Cabeza, Luisa F.
Despite the fact that there are some commercial concentrated solar power plants worldwide, there is currently a lack of experimental reports about the operational characteristics of this type of plants. Therefore, a two-tank molten salts thermal energy storage (TES) pilot plant at the University of Lleida (Spain) was used to analyze charging and discharging processes under real conditions. In this facility, 1000 kg of molten salts are used as TES material and Therminol VP-1 is used as heat transfer fluid (HTF). This facility is equipped with measurement equipment which allows an exhaustive analysis of the processes. In this study, the fact of varying the flow arrangement in the heat exchanger (parallel and counter flow arrangements) and the temperature difference between the molten salts and the HTF have been studied and discussed in terms of temperature profiles, energy and power stored/released from/to both HTF and molten salts, efficiencies and effectiveness. The best working conditions found were counter flow arrangement with a temperature grading of about 65 °C., The research leading to these results has received funding from Spanish government (Fondo tecnológico IDI-20090393, ConSOLida CENIT 2008-1005) and from Abengoa Solar NT. The work is partially funded by the Spanish government (ENE2008-06687-C02-01/CON, ENE2011-28269-C03-02, ENE2011-22722 and ULLE10-4E-1305). The authors would like to thank the Catalan Government for the quality accreditation given to their research group GREA (2014 SGR 123). This project has also received funding from the European Commission Seventh Framework Programme (FP/2007-2013) under Grant agreement N°PIRSES-GA-2013-610692 (INNOSTORAGE) and from the European Union’s Horizon 2020 research and innovation programme under grant agreement No 657466 (INPATH-TES). Laia Miró would like to thank the Spanish Government for her research fellowship (BES-2012-051861). Jaume Gasia would like to thank the Departament d’Universitats, Recerca i Societat de la Informació de la Generalitat de Catalunya for his research fellowship (2016FI_B 00047).
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Experimental analysis of hydroquinone used as phase change material (PCM) to be applied in solar cooling refrigeration, Analyse expérimentale de l'hydroquinone utilisée comme matériau à changement de phase dans les applications de refroidissement solaire

  • Gil, Antoni
  • Oró Prim, Eduard
  • Miró, Laia
  • Peiró Bell-lloch, Gerard
  • Ruiz-Pardo, Álvaro
  • Salmerón, José Manuel
  • Cabeza, Luisa F.
This present paper is focused on the study of high temperature thermal energy storage (TES) using phase change materials (PCM) to be applied on cooling and refrigeration systems by solar cooling. Thus, a pilot plant with a working temperature range between 150 and 200 C was designed and built at the University of Lleida (Spain). Hydroquinone was selected for the specific application from different PCM candidates as the most suitable material after a literature review and a differential scanning calorimetry (DSC) analysis. This PCM has a phase change temperature range between 166 C and 173 C and a melting enthalpy of 225 kJ kg 1. Two storage configurations were evaluated using the same PCM to have preliminary results before the final storage tank design. From the pilot plant results and experience, a 5 Tn PCM storage tank was designed and built to work in a real solar cooling installation in Seville (Spain)., The work is partially funded by the Spanish government (ENE2011-22722). The authors would like to thank the Catalan Government for the quality accreditation given to their research group GREA (2009 SGR 534). Antoni Gil would like to thank the Col·legi d'Enginyers Industrials de Catalunya for his research appointment. Eduard Oró would like to thank the University of Lleida for his research fellowship.
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Review on phase change materials (PCMs) for cold thermal energy storage applications

  • Oró Prim, Eduard
  • Gracia Cuesta, Alvaro de
  • Castell, Albert
  • Farid, Mohammed M.
  • Cabeza, Luisa F.
Thermal energy storage (TES) is a technology with a high potential for different thermal applications. It is well known that TES could be the most appropriate way and method to correct the gap between the demand and supply of energy and therefore it has become a very attractive technology. In this paper, a review of TES for cold storage applications using solid–liquid phase change materials has been carried out. The scope of the work was focussed on different aspects: phase change materials (PCMs), encapsulation, heat transfer enhancement, and the effect of storage on food quality. Materials used by researchers as potential PCM at low temperatures (less than 20 C) are summarized and some of their thermophysical properties are reported. Over 88 materials that can be used as PCM, and about 40 commercially available PCM have been listed. Problems in long term stability of the materials, such as corrosion, phase segregation, stability under extended cycling or subcooling are discussed. Heat transfer is considered both from theoretical and experimental point of view and the different methods of PCM encapsulation are reviewed. Many applications of PCM at low temperature can be found, such as, ice storage, conservation and transport of temperature sensitive materials and in air conditioning, cold stores, and refrigerated trucks., The work partially funded by the Spanish Government (ENE2008-06687-C02-01/CON and ENE2011-22722) and the European Union (COST Action COST TU0802 and project EFFIBUILDINGS – FP7-PEOPLE-2009-IIF-/-253914). The authors would like to thank the Catalan Government for the quality accreditation given to their research group (2009 SGR 534). Eduard Oró would like to thank the University of Lleida for his research fellowship.
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Thermal behaviour of D-mannitol when used as PCM: Comparison of results obtained by DSC and in a thermal energy storage unit at pilot plant scale

  • Gil, Antoni
  • Barreneche Güerisoli, Camila
  • Moreno Argilés, Pere
  • Solé Cutrona, Cristian
  • Fernández Renna, Ana Inés
  • Cabeza, Luisa F.
The use of thermal energy storage (TES) systems for solar heating and cooling applications has received considerable attention in recent decades because it has a high potential in energy savings. Phase change materials (PCMs) can store large amount of energy per mass unit compared with other TES materials. Nevertheless, the selection of the suitable PCM for each application is a key issue in any TES system design. The most important properties to take into account to select a PCM are the melting and solidification temperature, the phase change enthalpy and the stability after several thermal cycles. In this paper, D-mannitol was a candidate material to be tested as PCM in a solar cooling application due to its melting point (167 C) and a relatively high enthalpy (316.0 kJ/kg). The experiments performed by DSC have shown that the D-mannitol presents polymorphic structural changes and, therefore, its thermal properties are not always the same. Depending on the polymorphic phase obtained, D-mannitol has different melting temperature. This behaviour was corroborated in a storage tank, where it may be seen that the cooling rate of the D-mannitol is a key parameter in the formation of the different polymorphic phases., The work is partially funded by the Spanish government (ENE2011-22722). The authors would like to thank the Catalan Government for the quality accreditation given to their research group GREA (2009 SGR 534) and research group DIOPMA (2009 SGR 645). A. Gil would like to thank the Col·legi d’Enginyers Industrials de Catalunya for his research appointment.
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Physico-chemical and mechanical properties of microencapsulated phase change material

  • Giro-Paloma, Jessica
  • Oncins, Gerard
  • Barreneche Güerisoli, Camila
  • Martínez, Mònica
  • Fernández Renna, Ana Inés
  • Cabeza, Luisa F.
Microencapsulated phase change materials (MPCM) are well known in advanced technologies for the utilization in active and passive systems, which have the capacity to absorb and slowly release the latent heat involved in a phase change process. Microcapsules consist of little containers, which are made of polymer on the outside, and paraffin wax as PCM in the inside. The use of microencapsulated PCM has many advantages as microcapsules can handle phase change materials as core allowing the preparation of slurries. However there are some concerns about cycling of MPCM slurries because of the breakage of microcapsules during charging/discharging and the subsequent loss of effectiveness. This phenomenon motivates the study of the mechanical response when a force is applied to the microcapsule. The maximum force that Micronal® DS 5001 can afford before breaking was determined by Atomic Force Microscopy (AFM). To simulate real conditions in service, assays were done at different temperatures: with the PCM in solid state at 25 ºC, and with the PCM melted at 45 ºC and 80 ºC. To better understand the behavior of these materials, Micronal® DS 5001 microcapsules were characterized using different physic-chemical techniques. Microcapsules Fourier Transform Infrared Spectroscopy (FT-IR) results showed the main vibrations corresponding to acrylic groups of the outside polymer. Thermal stability was studied by Thermogravimetrical Analysis (TGA), and X-ray Fluorescence (XRF) was used to characterize the resulting inorganic residue. The thermal properties were determined using Differential Scanning Calorimetry (DSC) curves. Particles morphology was studied with Scanning Electron Microscopy (SEM) and Mie method was used to evaluate the particle size distribution. Samples had a bimodal distribution of size and were formed by two different particles sizes: agglomerates of 150 lm diameter formed by small particles of 6 lm. Atomic Force Microscopy in nanoindentation mode was used to evaluate the elastic response of the particles at different temperatures. Different values of effective modulus Eeff were calculated for agglomerates and small particles. It was observed that stiffness depended on the temperature assay and particle size, as agglomerates showed higher stiffness than small particles, which showed an important decrease in elastic properties at 80 ºC., The work is partially funded by the Spanish government (ENE2011-28269-C03-02 and ENE2011-22722) and the European Union (COST Action TU0802). The authors would like to thank the Catalan Government for the quality accreditation given to their research group GREA (2009 SGR 534) and research group DIOPMA (2009 SGR 645).
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Phase change materials and thermal energy storage for buildings

  • Cabeza, Luisa F.
  • Gracia Cuesta, Alvaro de
It is well known that there is a need to develop technologies to achieve thermal comfort in buildings lowering the cooling and heating demand. Research has shown that thermal energy storage (TES) is a way to do so, but also other purposes can be pursued when using TES in buildings, such as peak shaving or increase of energy efficiency in HVAC systems. This paper reviews TES in buildings using sensible, latent heat and thermochemical energy storage. Sustainable heating and cooling with TES in buildings can be achieved through passive systems in building envelopes, Phase Change Materials (PCM) in active systems, sorption systems, and seasonal storage., The work partially funded by the Spanish government (ENE2011-22722 and ULLE10-4E-1305). The authors would like to thank the Catalan Government for the quality accreditation given to their research group (2014 SGR 123). The research leading to these results has received funding from the European Union’s Seventh Framework Programme (FP7/2007-2013) under grant agreement no. PIRSES-GA-2013-610692 (INNOSTORAGE). Alvaro de Gracia would like to thank Education Ministry of Chile for Grant PMI ANT1201.
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Comparison of phase change slurries: Physicochemical and thermal properties

  • Giro-Paloma, Jessica
  • Barreneche Güerisoli, Camila
  • Martínez, Mònica
  • Šumiga, Boštjan
  • Cabeza, Luisa F.
  • Fernández Renna, Ana Inés
Phase change slurries (PCS) consist on a carrier fluid binary system, where water is mostly used as continuous phase and micro-encapsulated phase change materials (MPCM) are used as dispersed phase. PCS are used in Thermal Energy Storage (TES) for building applications, combining the latent heat capacity of the MPCM with the sensible heat capacity of the carrier fluid, and at the same time giving the PCM pumpable properties. In this study, two PCS samples are compared and characterized, the commercial Micronal® DS 5007 X from BASF and a laboratory made PCS28. Thereby, in this paper thermal stability is studied by using thermogravimetrical analysis (TGA) and the main components of the MPCM have been studied using Fourier transformed infrared spectroscopy (FT-IR). Moreover, TGA coupled with FT-IR is used to study deeply the thermal decompositions of the PCS microcapsules and products derived thereof. Finally, differential scanning calorimetry (DSC) is performed to study the melting enthalpy and the melting temperature range of the phase change material (PCM). This paper concludes that both types of PCS have good potential from thermal energy storage purposes such as solar space heating applications., The work is partially funded by the Spanish government (ENE2011-28269-C03-02 and ENE2011-22722). The authors would like to thank the Catalan Government for the quality accreditation given to their research group GREA (2014 SGR 123) and research group DIOPMA (2014 SGR 1543). The research leading to these results has received funding from the European Union's Seventh Framework Programme (FP7/2007-2013) under grant agreement n° PIRSES-GA-2013-610692 (INNOSTORAGE).
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Thermal storage in a MW scale. Molten salt solar thermal pilot facility: Plant description and commissioning experiences

  • Prieto, Cristina
  • Osuna, Rafael
  • Fernández Renna, Ana Inés
  • Cabeza, Luisa F.
In 2008, following its R&D strategy roadmap for Concentrated Solar Power, Abengoa designed, built and tested a unique Molten Salts pilot plant at the representative scale of 8 MWhth, coupled with a trough oil loop. The objectives of this project were based on evaluating the technology at a scale at which the results are sufficiently representative of the real circumstances facing a commercial plant that utilizes this storage technology. To this end, the MS-TES plant was brought into operation on January 19th, 2009, been the first demo plant of indirect double tank storage in operation in the world. Key points such a material corrosion, analysis of possible leakage points, calculation of performance or true efficiency of the storage (including a thorough assessment of thermal losses) and analysis of plant operation are the lines that have been analysed at this plant. Operational aspects such as the mechanical assembling, the pre-heating, the filling up and plant performance were deeply addressed. Key components as the storage tanks, the heat exchanger, the molten salts pumps, the heat-tracing systems or valves and instrumentation were tested. In this first paper, the description and commissioning of the plant is presented together a set of lessons learnt to be applied at the commercial plant scale., The research leading to these results has received funding from Spanish government (Fondo tecnológico IDI-20090393, ConSOLida CENIT2008-1005). The work is partially funded by the Spanish government (ENE2008-06687-C02-01, ENE2011-28269-C03-02, ENE2011-22722). The authors would like to thank the Catalan Government for the quality accreditation given to their research group GREA (2014 SGR 123) and research group DIOPMA (2014 SGR 1543).
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Influence of the heat transfer fluid in a CSP plant molten salts charging process

  • Peiró Bell-lloch, Gerard
  • Gasia, Jaume
  • Miró, Laia
  • Prieto, Cristina
  • Cabeza, Luisa F.
The selection of a proper heat transfer fluid (HTF) is a key factor to increase the efficiency of concentrated solar power plants and therefore, to reduce their internal associated CAPEX (capital expenditures of developing and constructing a plant, excluding any grid-connection charges) and OPEX (operating expenditures from the first year of a project's operation). This paper presents a comparative study of two commercial HTF which are widely used in different industries and CSP plants: thermal oil Therminol VP-1 and silicone fluid Syltherm 800. First, the authors theoretically studied the properties of both HTF based on the data given by the manufactures. Afterwards, the authors experimentally perform the comparison in a two-tank molten salt thermal energy storage pilot plant built at the University of Lleida (Spain). The study is focused on the plate heat exchanger of the facility during several charging processes with a counter flow arrangement. Results from both studies showed that, for the same working conditions, Therminol VP-1 is the best candidate for the above-mentioned purposes due to its higher heat transfer, lower thermal losses and lower power consumption associated to the HTF pump. However, it presents problems a low crystallization point, which should also be considered., The research leading to these results has received funding from Spanish goverment (Fondo tecnológico IDI-20090393, ConSOLida CENIT 2008-1005) and from Abengoa Solar NT. The work is partially funded by the Spanish government (ENE2008-06687-C02-01/CON, ENE2011-22722, ULLE10-4E-1305 and ENE2015-64117-C5-1-R (MINECO/FEDER)). The authors would like to thank the Catalan Government for the quality accreditation given to their research group GREA (2014 SGR 123). This project has also received funding from the European Commission Seventh Framework Programme (FP/2007-2013) under Grant agreement NºPIRSES-GA-2013-610692 (INNOSTORAGE) and from the European Union’s Horizon 2020 research and innovation programme under grant agreement No 657466 (INPATH-TES). Laia Miró would like to thank the Spanish Government for her research fellowship (BES-2012-051861). Jaume Gasia would like to thank the Departament d’Universitats, Recerca i Societat de la Informació de la Generalitat de Catalunya for his research fellowship (2017FI_B1 00092). The authors would like to thank Dr. Eduard Oró from Catalonia Institute for Energy Research (Spain) and Dr. Antoni Gil from Massachusetts Institute of Technology (USA) for their help during the initial stages of the experimentation.
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Key performance indicators in thermal energy storage: survey and assessment

  • Cabeza, Luisa F.
  • Galindo, Esther
  • Prieto, Cristina
  • Barreneche Güerisoli, Camila
  • Fernández Renna, Ana Inés
Thermal energy storage (TES) is recognised as a key technology for further deployment of renewable energy and to increase energy efficiency in our systems. Several technology roadmaps include this technology in their portfolio to achieve such objectives. In this paper, a first attempt to collect, organise and classify key performance indicators (KPI) used for TES is presented. Up to now, only KPI for TES in solar power plants (CSP) and in buildings can be found. The listed KPI are quantified in the literature and compared in this paper. This paper shows that TES can only be implemented by policy makers if more KPI are identified for more applications. Moreover, close monitoring of the achievements of the already identified KPI needs to be carried out to demonstrate the potential of TES., The work is partially funded by the Spanish Government (ENE2011-28269-C03-02, ENE2011-22722). The authors would like to thank the Catalan Government for the quality accreditation given to their research group GREA (2014 SGR 123) and research group DIOPMA (2014 SGR 1543). The research leading to these results has received funding from the European Union's Seventh Framework Programme (FP7/2007-2013) under grant agreement n° PIRSES-GA-2013-610692 (INNOSTORAGE).
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Review on system and materials requirements for high temperature thermal energy storage. Part 1: General requirements

  • Gasia, Jaume
  • Miró, Laia
  • Cabeza, Luisa F.
High temperature thermal energy storage offers a huge energy saving potential in industrial applications such as solar energy, automotive, heating and cooling, and industrial waste heat recovery. However, certain requirements need to be faced in order to ensure an optimal performance, and to further achieve widespread deployment. In the present review, these requirements are identified for high temperature (>150 °C) thermal energy storage systems and materials (both sensible and latent), and the scientific studies carried out meeting them are reviewed. Currently, there is a lack of data in the literature analysing thermal energy storage from both the systems and materials point of view. In the part 1 of this review more than 25 requirements have been found and classified into chemical, kinetic, physical and thermal (from the material point of view), and environmental, economic and technologic (form both the material and system point of view). The enhancements focused on the thermal conductivity are addressed in the Part 2 of this review due to their research significance and extension., The work is partially funded by the Spanish government (ENE2015-64117-C5-1-R, ENE2011-22722 and ULLE10-4E-1305). The authors would like to thank the Catalan Government for the quality accreditation given to their research group GREA (2014 SGR 123). This project has received funding from the European Commission Seventh Framework Programme (FP/2007-2013) under Grant agreement No. PIRSES-GA-2013-610692 (INNOSTORAGE) and from the European Union's Horizon 2020 research and innovation programme under grant agreement No. 657466 (INPATH-TES). Laia Miró would like to thank the Spanish Government for her research fellowship (BES-2012-051861). Jaume Gasia would like to thank the Departament d'Universitats, Recerca i Societat de la Informació de la Generalitat de Catalunya for his research fellowship (2016FI_B 00047).
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Enthalpy-temperature plots to compare calorimetric measurements of phase change materials at different sample scales

  • Rathgeber, Christoph
  • Schmit, Henri
  • Miró, Laia
  • Cabeza, Luisa F.
  • Gutiérrez, Andrea
  • Ushak, Svetlana
  • Hiebler, Stefan
Phase change materials (PCM) can provide high thermal energy storage capacities in narrow temperature ranges around their phase change temperature. The expectable maximum storage capacity of a PCM in a defined temperature range is equal to the enthalpy change in that range and can be determined via calorimetric measurements such as differential scanning calorimetry (DSC) or T-History calorimetry. T-History samples (aprox. 15 ml) are about 1000 times larger than DSC samples (aprox. 15 ml). Experiments in a pilot plant are performed to study the charging and discharging behaviour of even larger amounts of the PCM (aprox. 150 l). The common practise is to investigate PCM at one scale, rarely at two scales. In this work, the characterisation was carried out at three scales (DSC, T-History, and pilot plant) for four PCM (RT58, bischofite, D-mannitol, and hydroquinone). Thereby, the question arises how the enthalpy changes measured at different scales and under different conditions can be compared. In literature, the melting enthalpy is usually assigned to a single temperature without indicating the temperature range considered for evaluation. In very few instances, the enthalpy change within a defined temperature range is stated. In both cases, results measured under different conditions are difficult to compare. In this work, it is demonstrated that enthalpy-temperature plots facilitate the comparison and interpretation of measurements obtained under different experimental methods at different sample scales., The work of ZAE Bayern was part of the project EnFoVerM and was supported by the German Federal Ministry for Economic Affairs and Energy under the project code 0327851D. The work at the University of Lleida is partially funded by the Spanish government (ENE2011-22722, ENE2015-64117-C5-1-R (MINECO/FEDER) and ULLE10-4E-1305). The authors would like to thank the Catalan Government for the quality accreditation given to their research group GREA (2014 SGR 123). GREA is a certified agent TECNIO in the category of technology developers from the Government of Catalonia. The research leading to these results has received funding from the European Union's Seventh Framework Programme (FP7/2007-2013) under grant agreement n° PIRSES-GA-2013-610692 (INNOSTORAGE) and from the European Union’s Horizon 2020 research and innovation programme under grant agreement No 657466 (INPATH-TES). The authors want also to thank the collaboration of Antoni Gil from Massachusetts Institute of Technology (USA), Eduard Oró from Catalonia Institute for Energy Research (Spain), and Jaume Gasia and Gerard Peiró from University of Lleida (Spain). Laia Miró would like to thank the Spanish Government for her research fellowship (BES-2012-051861). The work of the University of Antofagasta was supported by FONDAP SERC-Chile (grant N° 15110019), and the Education Ministry of Chile Grant PMI ANT 1201. Authors thank the SALMAG Company for providing of bischofite. Andrea Gutierrez would like to acknowledge to the Ministry of Education of Chile her doctorate scholarship ANT 1106 and CONICYT/PAI N° 7813110010.
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Computational efficiency in numerical modeling of high temperature latent heat storage: comparison of selected software tools based on experimental data

  • Pointner, Harald
  • Gracia Cuesta, Alvaro de
  • Vogel, Julian
  • Tay, N. H. Steven
  • Liu, Ming
  • Johnson, Maike
  • Cabeza, Luisa F.
In this article, four different numerical models for the investigation of phase change processes within latent heat storage are described and compared concerning accuracy, convergence behavior and computational efficiency. The models are based on different types of discretization, make use of different ways to model phase change and are implemented with C, MATLAB or ANSYS CFX. After a brief introduction into each investigated numerical model, the experimental reference setup is described. It consists of a flat plate latent heat storage with the eutectic mixture NaNO3 (46 wt%)–KNO3 (54 wt%) with a measured melting temperature of 219.5 °C as storage material. Based on the corresponding simulation model developed in this paper, the comparison of the numerical models is achieved. This methodology allows the investigation of the numerical performance of different software tools in the context of high temperature latent heat storage that was not achieved thus far. All four numerical models show good agreement to experimental results but differ significantly in speed and convergence behavior., This work was partially funded by the nextPCM project supported by the German Federal Ministry for the Environment, Nature Conservation and Nuclear Safety. Moreover, the work was partially funded by the Spanish government (ENE2011-22722 and ULLE10-4E-1305). The authors Alvaro de Gracia and Luisa F. Cabeza would like to thank the Catalan Government for the quality accreditation given to their research group (2014-SGR-123). The research leading to parts of these results has received funding from the European Union’s Seventh Framework Programme (FP7/2007-2013) under grant agreement PIRSES-GA-2013-610692 (INNOSTORAGE). Alvaro de Gracia would like to thank the Education Ministry of Chile for Grant PMI ANT1201.
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Two-tank molten salts thermal energy storage system for solar power plants at pilot plant scale: Lessons learnt and recommendations for its design, start-up and operation

  • Peiró Bell-lloch, Gerard
  • Prieto, Cristina
  • Gasia, Jaume
  • Jové, Aleix
  • Miró, Laia
  • Cabeza, Luisa F.
Renewable energies are main players to ensure the long-term energy supply. Solar power plants with thermal energy storage (TES) are one of the available renewable technologies which have more potential. Nowadays, there are still several aspects in the design and operation of these power plants which need to be improved, such as the correct operation of some specific instrumentation, the compatibility between TES materials and storage tanks materials, and operational process strategies. This paper presents the acquired experience during the design, start-up, and operation of a kWh scale pilot experimental facility built at the University of Lleida (Spain) together with Abengoa Research (Spain) in 2008. The versatility of this facility has allowed simulating real working conditions and therefore testing different TES systems, TES materials, solar power plant components, and operational strategies focused on TES for temperatures up to 400 °C. In the present paper, the authors show the lessons learnt at pilot and present the main problems and limitations encountered, and give advices of this experimental set-up to extrapolate the data to real plant, to provide solutions to technical problems and reduce the cost of commercial plants., The authors want to thank specially to Dr. Eduard Oró (today at Institut de Recerca d’Energies de Catalunya, Spain) and Dr. Antoni Gil (today at Massachusetts Institute of Technology, USA) for their help in the design, start-up and operation of the pilot plant facility. The research leading to these results has received funding from Spanish government through CDTI granted projects (Fondo tecnológico IDI-20090393, ConSOLida CENIT 2008-1005) and from Abengoa Solar NT. The work is partially funded by the Spanish government (ENE2008-06687-C02-01/CON, ENE2011-22722, ULLE10-4E-1305, and ENE2015-64117-C5-1-R (MINECO/FEDER)). The authors would like to thank the Catalan Government for the quality accreditation given to their research group GREA (2014 SGR 123). GREA is a certified agent TECNIO in the category of technology developers from the Government of Catalonia. This project has received funding from the European Commission Seventh Framework Programme (FP/2007-2013) under Grant agreement NºPIRSES-GA-2013-610692 (INNOSTORAGE) and from the European Union’s Horizon 2020 research and innovation programme under grant agreement No 657466 (INPATH-TES). Laia Miró would like to thank the Spanish Government for her research fellowship (BES-2012-051861). Jaume Gasia would like to thank the Departament d'Universitats, Recerca i Societat de la Informació de la Generalitat de Catalunya for his research fellowship (2017FI_B1 00092).
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Review of the T-history method to determine thermophysical properties of phase change materials (PCM)

  • Solé, Aran
  • Miró, Laia
  • Barreneche Güerisoli, Camila
  • Martorell, Ingrid
  • Cabeza, Luisa F.
Phase change materials (PCM) are able to store thermal energy when becoming liquid and to releaseit when solidifying. Latent heat storage has gained importance due the applications towards increasing energy efficiency in severalsystems. Thus, a correct and accurate thermal characterization of these materials should be achieved. Among all possible thermal analysis methods to determine PCM thermophysical properties, the T-history method presents certain advantages. The T-history method is known to be suitable to obtain fusion enthalpy, specific heat and thermal conductivity for large phase change materials samples. On the other hand, no experimental T-history equipment isc ommercially available yet. Therefore, the goal of this paper is moving towards a consensus. To achieve this goal, a collection of similar methods previous to T-history are exposed and different proposals based on improving the original T-history method are discussed and reviewed., he work is partially funded by the Spanish government (ENE2011-28269-C03-02 and ENE2011-22722). The authors would like to thank the Catalan Government for the quality accreditation given to the research group GREA (2009 SGR 534). Aran Solé would like to thank the Departament d'Universitats, Recerca i Societat de la Informació de la Generalitat de Catalunya for her research fellowship. Laia Miró would like to thank the Spanish Government for her research fellowship (BES-2012-051861).
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Thermophysical characterization and thermal cycling stability of two TCM: CaCl2 and zeolite

  • Barreneche Güerisoli, Camila
  • Fernández Renna, Ana Inés
  • Cabeza, Luisa F.
  • Cuypers, Ruud
At this moment, the global energy consumption in buildings is around 40% of the total energy consumption in developed countries. Thermal energy storage (TES) is presented as one way to address this energyrelated problem proposing an alternative to reduce the gap between energy supply and energy demand. One way to store energy is using thermochemical materials (TCM). These types of materials allow accumulating energy through a chemical process at low temperature, almost without heat losses. In addition, it is a stable way to perform the heat storage and TCM can be implemented for seasonal storage or/and long term storage. This study compares the cyclability, from the thermophysical point of view, CaCl2 which follows a chemical reaction and zeolite which follows a sorption process to be used as TCM for seasonal/long term storage. The main results show that the chemical reaction TCM is more energy-efficient than the sorption TCM. The CaCl2 calculated energy density is 1.47 GJ/m3 , being the best option to be considered to be used as TCM, even though the dehydration process of the zeolite is simpler and it occurs at higher temperatures its calculated energy density is only 0.2 GJ/m3 ., The research leading to these results has received funding from the European Commission Seventh Framework Programme (FP/ 2007-2013) under grant agreement No ENER/FP7/1295983 (MERITS) and under grant agreement no. PIRSES-GA-2013-610692 (INNOSTORAGE). Furthermore, the work is partially funded by the Spanish government (ENE2011-28269-C03-02 and ENE2011- 22722), and the European Union by Cost Action TU0802. The authors would like to thank the Catalan Government for the quality accreditation given to their research groups GREA (2014 SGR 123) and DIOPMA (2014 SGR 1543).
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Corrosion of metals and salt hydrates used for thermochemical energy storage

  • Solé, Aran
  • Miró, Laia
  • Barreneche Güerisoli, Camila
  • Martorell, Ingrid
  • Cabeza, Luisa F.
Solar energy can be efficiently used if thermal energy storage systems are accordingly designed to match availability and demand. Thermal energy storage by thermochemical materials (TCM) is very attractive since these materials present a high storage density. Therefore, compact systems can be designed to provide both heating and cooling in dwellings. One of the main drawbacks of the TCM is corrosion with metals in contact. Hence, the objective of this study is to present the obtained results of an immersion corrosion test following ASTM G1 simulating an open TCM reactor, under humidity and temperature defined conditions. Four common metals: copper, aluminum, stainless steel 316, and carbon steel, and five TCM: CaCl2, Na2S, CaO, MgSO4, and MgCl2, were studied. Aluminum and copper show severe corrosion when combined with Na2S, aluminum corrosion is more significant since the specimen was totally destroyed after 3 weeks. Stainless steel 316 is recommended to be used as a metal container material when storing all tested TCM., The research leading to these results has received funding from the European Commission Seventh Framework Programme (FP/2007-2013) under grant agreement no ENER/FP7/295983 (MERITS). Aran Solé would like to thank the Departament d'Universitats, Recerca i Societat de la Informació de la Generalitat de Catalunya for her research fellowship. Laia Miró would like to thank the Spanish Government for her training researcher personal fellowship (BES-2012-051861). The work is partially funded by the Spanish Government (ENE2011-28269-C03-02 and ENE2011-22722). The authors would like to thank the Catalan Government for the quality accreditation given to the research group GREA (2014 SGR 123).
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Thermal energy storage (TES) for industrial waste heat (IWH) recovery: a review

  • Miró, Laia
  • Gasia, Jaume
  • Cabeza, Luisa F.
Industrial activities have a huge potential for waste heat recovery. In spite of its high potential, industrial waste heat (IWH) is currently underutilized. This may be due, on one hand, to the technical and economic difficulties in applying conventional heat recovery methods and, on the other, the temporary or geographical mismatch between the energy released and its heat demand. Thermal energy storage (TES) is a technology which can solve the existing mismatch by recovering the IWH and storing it for a later use. Moreover, the use of recovered IWH leads to a decrease of CO2 emissions and to economic and energy savings. Depending on the distance between the IWH source and the heat demand, TES systems can be placed on-site or the IWH can be transported by means of mobile TES systems, to an off-site heat demand. Around 50 industry case studies, in which both on-site and off-site recovery systems are considered are here reviewed and discussed taking into account the characteristics of the heat source, the heat, the TES system, and the economic, environmental and energy savings. Besides, the trends and the maturity of the cases reviewed have been considered. On-site TES systems in the basic metals manufacturing are the technology and industrial sector which has focused the most attention among the researchers, respectively. Moreover, water (or steam), erythritol and zeolite are the TES materials used in most industries and space comfort and electricity generation are the most recurrent applications., The work is partially funded by the Spanish government (ENE2011-22722, ENE2015-64117-C5-1-R (MINECO/FEDER)). This project has received funding from the European Commission Seventh Framework Programme (FP/2007-2013) under Grant agreement No. PIRSES-GA-2013-610692 (INNOSTORAGE) and from the European Union’s Horizon 2020 research and innovation programme under grant agreement No. 657466 (INPATH-TES). The authors would like to thank the Catalan Government for the quality accreditation given to their research group GREA (2014 SGR 123). Jaume Gasia would like to thank the Departament d’Universitats, Recerca i Societat de la Informació de la Generalitat de Catalunya for his research fellowship (2016FI_B 00047). Laia Miró would like to thank the Spanish Government for her research fellowship (BES-2012-051861).
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Materials selection for thermal energy storage systems in parabolic trough collector solar facilities using high chloride content nitrate salts

  • Ruiz-Cabañas, F. Javier
  • Prieto, Cristina
  • Madina, Virginia
  • Fernández Renna, Ana Inés
  • Cabeza, Luisa F.
The increasing role of concentrated solar power (CSP) within the renewable energy portfolio is attributed to the possibility of integrating thermal energy storage (TES) systems. Then, CSP technology has become one of the most interesting clean options to deliver dispatchable power on demand. Nowadays, commercial facilities use high quality solar salts (60%:40% NaNO3 and KNO3 by weight) as storage medium due to the attractive properties of this fluid to be applied under CSP operation conditions. Taking into account that CSP installations are designed with really large TES systems containing tens of thousands of tons, the use of lower quality nitrates salts would reduce the molten salts inventory cost and finally the investment cost of the CSP storage systems at commercial scale. The most important drawback of selecting low quality nitrates salts for high temperature CSP applications is the corrosion impact produced by impurities. Accordingly, chlorides have been identified in the state of the art as the impurity with higher effect over corrosion. This work is focused on A516 Gr70 carbon steel corrosion performance evaluation under high-chlorides content nitrates salts (1.2% and 3% by weight) at 400 °C. In addition, the feasibility of using the proposed low purity mixtures with current CSP facilities materials selection is analyzed. Results reported within this study show the critical effect of chloride content over corrosion mechanism producing lack of adherence between base metal and oxides layers in addition to corrosion products delamination and internal cracking. Then, the use of A516 Gr70 carbon steel is rejected for a long term design under solar salts containing chlorides content in the range 1.2–3% by weight being necessary a higher corrosion resistant materials selection. An improved materials selection focused on higher corrosion resistance alloys is discussed., The research leading to these results has received funding from Spanish government (Fondo tecnológico IDI-20090393, ConSOLida CENIT 2008-1005). The work is partially funded by the Spanish government (ENE2011-28269-C03-02, ENE2011-22722, ENE2015-64117-C5-1-R (MINECO/FEDER), and ENE2015-64117-C5-2-R (MINECO/FEDER)). The authors would like to thank the Catalan Government for the quality accreditation given to their research group GREA (2014 SGR 123) and research group DIOPMA (2014 SGR 1543).
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Control of a PCM ventilated facade using reinforcement learning techniques

  • Gracia Cuesta, Alvaro de
  • Fernàndez Camon, César
  • Castell, Albert
  • Mateu Piñol, Carles
  • Cabeza, Luisa F.
Artificial intelligence techniques have been successfully applied to control dynamic systems looking for an optimal control. Among those techniques, reinforcement learning has been shown as particularly effective at reducing the dimensionality of some real problems and solving control problems by learning from experience. The use of thermal energy storage active systems in the building sector is identified as suitable option to reduce their energy demand for heating and cooling. However, these systems might be expensive and require appropriate control strategies in order to improve the performance of the building. In this paper a ventilated facade with PCM is controlled using a reinforcement learning algorithm. The ventilated facade uses mechanical ventilation during nighttime to solidify the PCM and releases this cold stored to the inner environment during the peak demand period. It is crucial to decide correctly the schedule of charge and discharge process of the PCM according to the weather and indoor conditions. An experimentally validated numerical model is used to test the performance of the control algorithm under different weather conditions. Important improvements on the energy savings due to the use of control strategies were found and supported by the data under the different tested climatic conditions., The work partially funded by the Spanish government (ENE2011-28269-C03-01, ENE2011-22722 and ULLE10-4E-1305). The authors would like to thank the Catalan Government for the quality accreditation given to their research group (2014-SGR-123). The research leading to these results has received funding from the European Union’s Seventh Framework Programme (FP7/2007-2013) under grant agreement #PIRSES-GA-2013-610692 (INNOSTORAGE). Alvaro de Gracia would like to thank Education Ministry of Chile for Grant PMI ANT1201.
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Corrosion of metal containers for use in PCM energy storage

  • Ferrer, Gerard
  • Solé, Aran
  • Barreneche Güerisoli, Camila
  • Martorell, Ingrid
  • Cabeza, Luisa F.
In recent years, thermal energy storage (TES) systems using phase change materials (PCM) have been widely studied and developed to be applied as solar energy storage units for residential heating and cooling. These systems performance is based on the latent heat due to PCM phase change, a high energy density that can be stored or released depending on the needs. PCM are normally encapsulated in containers, hence the compatibility of the container material with the PCM has to be considered in order to design a resistant container. Therefore, the main aim of this paper is to study the corrosion effects when putting in contact five selected metals (aluminium, copper, carbon steel, stainless steel 304 and stainless steel 316) with four different PCM (one inorganic mixture, one ester and two fatty acid eutectics) to be used in comfort building applications. Results showed corrosion on aluminium specimens. Hence caution must be taken when selecting it as an inorganic salt container. Despite copper has a corrosion rate range of 6e10 mg/cm2 yr in the two fatty acid formulations tested, it could be used as container. Stainless steel 316 and stainless steel 304 showed great corrosion resistance (0e1 mg/cm2 yr) and its use would totally be recommended with any of the studied PCM., The work is partially funded by the Spanish Government (ENE2011-28269-C03-02 and ENE2011-22722). The authors would like to thank the Catalan Government for the quality accreditation given to their research groups GREA (2014 SGR 123) and research group DIOPMA (2014 SGR 1543). Aran Sole would like to thank the Departament d'Universitats, Recerca i Societat de la Informacio de la Generalitat de Catalunya for her research fellowship. The research leading to these results has received funding from the European Union's Seventh Framework Programme (FP7/2007- 2013) under grant agreement n PIRSES-GA-2013-610692 (INNOSTORAGE)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Experimental evaluation at pilot plant scale of multiple PCMs (cascaded) vs. single PCM configuration for thermal energy storage

  • Peiró Bell-lloch, Gerard
  • Gasia, Jaume
  • Miró, Laia
  • Cabeza, Luisa F.
The present paper provides on one hand, a literature review of the different studies available in the scientific literature where the concept of multiple phase change materials (PCM) configuration, also named cascaded or multi-stage, has been presented and on the other hand, an experimental evaluation of the advantages of using the multiple PCM configuration instead of the single PCM configuration in thermal energy storage (TES) systems at pilot plant to fill the gap of experimental and high scales studies on this concept in the literature. Two PCM with melting temperatures in a temperature range of 150 e200 C were selected due to their high value of heat of fusion and compared: d-mannitol and hydroquinone. Three configurations were evaluated: (1) single PCM with hydroquinone, (2) single PCM with dmannitol and (3) multiple PCM with hydroquinone and d-mannitol. A discussion regarding the results on the specific energy stored and effectiveness as well as the evolution of the PCM and heat transfer fluid (HTF) through the time and at different and representative locations of the facility is presented. Results showed that the multiple PCMs configuration introduced an effectiveness enhancement of 19.36% if compared with single PCM configuration as well as a higher uniformity on the HTF temperature difference between the inlet and outlet., The work is partially funded by the Spanish Government (ENE2011-22722 and ULLE10-4E-1305). The authors would like to thank the Catalan Government for the quality accreditation given to their research group GREA (2014 SGR 123). The research leading to these results has received funding from the European Union's Seventh Framework Programme (FP7/2007-2013) under grant agreement n PIRSES-GA-2013-610692 (INNOSTORAGE). Laia Miro would like to thank the Spanish Government for her research fellowship (BES-2012-051861).
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

TES-PS10 postmortem tests: Carbon steel corrosion performance exposed to molten salts under relevant operation conditions and lessons learnt for commercial scale-up

  • Ruiz-Cabañas, F. Javier
  • Prieto, Cristina
  • Madina, Virginia
  • Fernández Renna, Ana Inés
  • Cabeza, Luisa F.
Postmortem tests were performed over components removed from the TES-PS10 pilot plant after almost four years of continuous operation being exposed to solar salts under representative commercial operation conditions. Accordingly, corrosion performance of plates sections extracted from both storage tanks and samples cut from the hot molten salts pump were evaluated. Corrosion damage extension, oxides layers morphology, and corrosion products chemistry were analyzed by X-ray diffraction, energy dispersive X-ray spectrometry, optical microscopy, and SEM. In addition to materials compatibility with molten salts, mechanical tests were carried out over the storage tanks plates sections. Although the corrosion damage extension over the plates extracted from storage tanks was low and the mechanical properties were according to the standard, some interesting observations were seen. For example, a sample extracted from the hot storage tank and exposed to intermittent contact with molten salts showed some areas characterized by the growth of a non-protective oxide scale. Moreover, localized corrosion with slight penetration through the base material was identified for all storage plates samples under evaluation. On the other hand, the molten salt pump parts under study showed adherent and uniform oxides layers without detecting corrosion–erosion phenomena. Some cavities were found in the discharge elbow, and these imperfections were associated to a bad metallurgical quality during casting. Summarizing, corrosion phenomena suffered by the components under evaluation could be corrected in future plants by applying the lessons learned discussed in this study. As conclusion, materials selection analyzed within this postmortem evaluation is valid from the corrosion point of view to be used in the design of commercial TES systems in PTC plants., The research leading to these results has received funding from Spanish government (Fondo tecnológico IDI-20090393, ConSOLida CENIT 2008-1005). The work is partially funded by the Spanish Government (ENE2011-28269-C03-02, ENE2011-22722, ENE2015-64117-C5-1-R, and ENE2015-64117-C5-2-R). The authors would like to thank the Catalan Government for the quality accreditation given to their research group GREiA (2017 SGR 1537) and research group DIOPMA (2017 SGR 138). GREiA and DIOPMA are certified agents TECNIO in the category of technology developers from the Government of Catalonia.
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Industrial waste materials and by-products as thermal energy storage (TES) materials: A review

  • Gutierrez, Andrea
  • Miró, Laia
  • Gil, Antoni
  • Rodríguez Aseguinolaza, Javier
  • Barreneche Güerisoli, Camila
  • Calvet, Nicolas
  • Py, Xavier
  • Fernández Renna, Ana Inés
  • Grágeda, Mario
  • Ushak, Svetlana
  • Cabeza, Luisa F.
A wide variety of potential materials for thermal energy storage (TES) have been identify depending on the implemented TES method, Sensible, latent or thermochemical. In order to improve the efficiency of TES systems more alternatives are continuously being sought. In this regard, this paper presents the review of low cost heat storage materials focused mainly in two objectives: on the one hand, the implementation of improved heat storage devices based on new appropriate materials and, on the other hand, the valorisation of waste industrial materials will have strong environmental, economic and societal benefits such as reducing the landfilled waste amounts, reducing the greenhouse emissions and others. Different industrial and municipal waste materials and by products have been considered as potential TES materials and have been characterized as such. Asbestos containing wastes, fly ashes, by-products from the salt industry and from the metal industry, wastes from recycling steel process and from copper refining process and dross from the aluminium industry, and municipal wastes (glass and nylon) have been considered. This work shows a great revalorization of wastes and by-product opportunity as TES materials, although more studies are needed to achieve industrial deployment of the idea., The work is partially funded by the Spanish government (ENE2011-28269-C03-02, ENE2011-22722 and ULLE10-4E-1305). The authors would like to thank the Catalan Government for the quality accreditation given to their research group GREA (2014 SGR 123) and research group DIOPMA (2014 SGR 1543). The research leading to these results has received funding from the European Union's Seventh Framework Programme (FP7/2007-2013) under grant agreement n° PIRSES-GA-2013-610692 (INNOSTORAGE). Laia Miró would like to thank the Spanish Government for her research fellowship (BES-2012-051861). The work at CIC Energigune was supported by the Department of Industry, Innovation, Commerce and Tourism of the Basque Country government through the ETORTEK CIC Energigune-2013 research program. Research at Masdar Institute is supported by the Government of Abu Dhabi to help fulfill the vision of the late President Sheikh Zayed bin Sultan Al Nayhan for sustainable development and empowerment of the UAE and humankind. Researchers of PROMES address all their gratitude to the French government for the funding of their work through the ANR SESCO and SACRE projects within the ANR SEED program. They also acknowledge the support of the CNRS, the University of Perpignan Via Domitia and the EUROPLASMA/INERTAM Company. The work at the University of Antofagasta was supported by CONICYT/FONDAP Nº 15110019, and the Education Ministry of Chile Grant PMI ANT 1201. Andrea Gutierrez would like to acknowledge to the Education Ministry of Chile her doctorate scholarship ANT 1106 and CONICYT/PAI N°7813110010.
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Selection and characterization of recycled materials for sensible thermal energy storage

  • Navarro, Maria E.
  • Martínez, Mònica
  • Gil, Antoni
  • Fernández Renna, Ana Inés
  • Cabeza, Luisa F.
  • Olives, R.
  • Py, Xavier
Alternative low cost materials are evaluated through the valorization of by-products derived from mining and metallurgical industry for solid sensible heat based energy storage systems. They were used either as received or formulated as aggregates in mortars, and their thermal and mechanical properties were characterized. A selection methodology was applied in order to compare them with available materials found in the literature for applications as (STES) materials, and with materials from Cambridge Educational Software (CES) Selector database. It was demonstrated that these recycled materials have a high potential for these thermal energy storage applications., This work was partially funded by the Spanish Government (Project ENE2008-06687-C02-01/CON and ENE2011-22722) and the European Union (COST Action COST TU0802). The authors at DIOPMA and GREA-UdL would like to thank the Catalan Government for the quality accreditation given to their research group, 2009 SGR 645 and 2009 SGR534 respectively. Antoni Gil would like to thank the Col·legi d'Enginyers Industrials de Catalunya for his research appointment and the Departament d'Universitats, Recerca i Societat de la Informació of Generalitat de Catalunya for the AGAUR research stage scholarship (BE-DGR 2010).
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Characterization of granular phase change materials for thermal energy storage applications in fluidized beds

  • Izquierdo Barrientos, M. A.
  • Sobrino, C.
  • Almendros Ibáñez, J. A.
  • Barreneche Güerisoli, Camila
  • Ellis, N.
  • Cabeza, Luisa F.
This work investigates commercially available granular phase change materials (PCMs) with different transition temperatures for the use of thermal-energy storage systems in fluidized beds. The hydrodynamic characteristics of granular PCMs were tested in cylindrical-3D and planar-2D fluidized beds. The density, particle size distribution and angle of repose were measured for various PCM materials. Further attrition studies were conducted with changes in particle surface from abrasion, which were characterized using a Scanning Electron Microscope (SEM). The results indicate that some materials with smaller particle size and thinner supporting structure can lose the paraffin during the fluidization process, when paraffin is in a liquid state. As a consequence, the particles agglomerate, and the bed defluidizes. For all of the tested materials, only GR50 (with a transition temperature of 50 °C) properly fluidizes when the paraffin is in the liquid state and has shown to endure >75 h of continuous operation and 15 melting-solidification cycles in a fluidized bed. Additional differential scanning calorimetry (DSC) measurements of the cycled particles did not show a decrease in energy storage capacity of the granular PCM, which corroborates that there is no loss of material after >75 h of fluidization., The work is partially funded by the Spanish government (ENE2010-15403, ENE2011-22722 and ENE2015-64117-C5-1). The authors would like to thank the Catalan Government for the quality accreditation to their research groups GREA (2014 SGR 123). The study that led to these results has received funding from the European Union’s Seventh Framework Programme (FP7/2007-2013) under grant agreement n°n°PIRSES-GA-2013-610692 (INNOSTORAGE) and from the European Union’s Horizon 2020 research and innovation programme under grant agreement No. 657466 (INPATH-TES).
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Physicochemical and thermal study of a MPCM of PMMA shell and paraffin wax as a core

  • Giro-Paloma, Jessica
  • Barreneche Güerisoli, Camila
  • Delgado, Mónica
  • Martínez, Mònica
  • Fernández Renna, Ana Inés
  • Cabeza, Luisa F.
The present work studies a Phase Change Slurry (PCS) as a proposed Thermal Energy Storage (TES) medium. Microencapsulation is an advanced technology to implement PCMs (Phase Change Material) avoiding leakage from building materials. The morphology and physicochemical properties of this Microencapsulated Phase Change Material (MPCM) sample were analyzed using some analytical techniques like Scanning Electron Microscopy (SEM), Infrared Spectroscopy (FT-IR), Thermogravimetrical Analysis (TGA), Differential Scanning Calorimeter (DSC), and Atomic Force Microscopy (AFM). The results showed that Micronal® DS 5007 is a suitable candidate to be used as slurry in active systems due to their studied mechanical properties., The work is partially funded by the Spanish government (ENE2011-28269-C03-02, ENE2011-22722, and ENE2011-28269-C03-01). The authors would like to thank the Catalan Government for the quality accreditation given to their research group GREA (2009 SGR 534) and research group DIOPMA (2009 SGR 645).
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Effect of D-mannitol polymorphism in its thermal energy storage capacity when it is used as PCM

  • Barreneche Güerisoli, Camila
  • Seth, Falguni
  • Fernández Renna, Ana Inés
  • Cabeza, Luisa F.
The main objective of this paper is to study the possible use of D-mannitol as phase change material (PCM) for thermal energy storage. PCM are materials that have high phase change enthalpy and this thermophysical property gives them the ability to store energy as latent heat. D-mannitol is a material which has different morphological phases (polymorphism); here were studied b-form and d-form. Different polymorphic forms produce changes on melting point of D-mannitol. For this reason it is necessary to establish a suitable working temperature range for the use of D-mannitol as phase change material. The thermal characterization was performed with DSC analysis using 0.5 K min-1 slow-dynamic method. Polymorphism analysis of D-mannitol was analyzed to associate the thermal behavior obtained by DSC with a specific polymorphic phase. D-mannitol presented three different thermal behaviors: the first one had a melting peak at 167 ºC, the second was a double melting peak at 155 ºC and 166 ºC, and the third a single peak at 155 ºC. Due to irregular results, two working range were studied and through the thermal characterization, it was possible to define a working range where Dmannitol could be used as PCM for energy storage: this range is between 135 and 175 ºC. Furthermore, it was possible to differentiate two crystalline phases of D-mannitol applying FT-IR analysis and to link them with thermal behavior observed in DSC. The percentage of times each thermal behavior is observed in DSC analysis was calculated. d-form is obtained 15.8% of analyzed cycles, the b-form appears 44.7% of times, and an intermediate transition between the two phases is found 39.5% of cycles., The work is partially funded by the Spanish government (ENE2011-22722) and the European Union (COST Action TU0802). The authors would like to thank the Catalan Government for the quality accreditation given to their research group GREA (2009 SGR 534) and research group DIOPMA (2009 SGR 645). A. Gil would like to thank the Col•legi d’Enginyers Industrials de Catalunya for his research appointment.
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Use of polyethylene glycol for the improvement of the cycling stability of bischofite as thermal energy storage material

  • Gutiérrez, Andrea
  • Ushak, Svetlana
  • Galleguillos, Hector
  • Fernández, Ángel G.
  • Cabeza, Luisa F.
  • Grágeda, Mario
Bischofite is a by-product of the non-metallic mining industry. It has been evaluated as phase change material in thermal energy storage, but it shows little cycling stability, therefore in this paper the mixture of bischofite with an additive was studied. Since polyethylene glycol (PEG) is a PCM itself, in this paper PEG (with different molecular weights) is used as additive in a PCM (bischofite) to improve its thermal behaviour. Results show that adding 5% PEG 2 000 to bischofite gives a more cycling stable PCM without affecting its melting temperature neither decreasing significantly its heat of fusion. This research shows that mixing an inorganic PCM with an organic additive can be a good option to improve the thermal performance of the PCM., The authors would like to acknowledge the collaboration of the company SALMAG. The authors acknowledge to FONDECYT (grant N 1120422), CONICYT/FONDAP N 15110019, and the Education Ministry of Chile Grant PMI ANT 1201 for the financial support. This work was partially funded by the Spanish project ENE2011-22722. Dr. Luisa F. Cabeza would like to acknowledge the Generalitat de Catalunya for the quality recognition 2014-SGR-123. Andrea Gutierrez would like to acknowledge for her doctorate scholarships to the Education Ministry of Chile (ANT 1106) and CONICYT/PAI N7813110010.
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Corrosion of metal and metal alloy containers in contact with phase change materials (PCM) for potential heating and cooling applications

  • Moreno Argilés, Pere
  • Miró, Laia
  • Barreneche Güerisoli, Camila
  • Solé Cutrona, Cristian
  • Martorell, Ingrid
  • Cabeza, Luisa F.
Thermal energy storage (TES) using phase change materials (PCM) can be used for load shaving or peak load shifting when coupled to a heating, ventilation, and air-conditioning (HVAC) system such as heat pump. In these systems the PCM is embedded in packages or used in bulk, so the compatibility of the encapsulation materials and the PCM is a key factor to ensure long operational life of the system. Although corrosion caused by salts is known from the chemical industry, when these salts are used as PCM no corrosion data is available, since the salts are used without being in water solution. Producing new corrosion data is essential for PCM utilisation in new applications. In this study the corrosion rate of two metals and two metal alloys when they are in contact with different salt hydrate PCM is evaluated; in total eleven PCM, being four of them commercial PCM, are tested. Since they are PCM to be used for heating and cooling applications they are classified in two different groups to present the corrosion study. Results present the recommendation of using each PCM with the different metals and metal alloys according to the obtained corrosion rate and visual observation of the samples., The work is partially funded by the Spanish Government (ENE2011-22722 and ENE2011-28269-C03-02).
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

On the use of filters to facilitate the post-optimal analysis of the Pareto solutions in multi-objective optimization

  • Antipova, Ekaterina
  • Pozo, C.
  • Guillén Gosálbez, Gonzalo
  • Boer, Dieter
  • Cabeza, Luisa F.
  • Jiménez Esteller, Laureano
Multi-objective optimization (MOO) has emerged recently as a useful technique in the design andplanning of engineering systems because it allows identifying alternatives leading to significant envi-ronmental savings. MOO models typically contain an infinite number of Pareto solutions, from whichdecision-makers should choose the best one according to their preferences. An approach is here pre-sented that identifies and retains for further inspection a reduced set of Pareto solutions showing betteroverall performance. The capabilities of our approach are illustrated through its application to the designof reverse osmosis desalination plants considering simultaneously the unitary production cost and a setof environmental impacts in several damage categories. Our method reduces significantly the number ofPareto points, thereby facilitating the decision-making process in MOO., The authors would like to acknowledge financial support from the Spanish Government(ENE2011-28269-C03-03, ENE2011-22722, DPI2012-37154-C02-02, CTQ2012-37039-C02) and the Catalan Government for the quality accreditation given to their research groups SUSCAPE and GREA (2009 SGR 545, 2009 SGR 534)