Skip to main content

CELULAS SOLARES NANOESTRUCTURADAS FABRICADAS A PARTIR DE DISOLUCIONES: MATERIALES INNOVADORES BASADOS EN NANOESTRUCTURAS DE CARBONO, Y SUS COMPOSITES E HIBRIDOS

ENE2013-48816-C5-5-R

•
Funding agency name Ministerio de Economía y Competitividad
Funding agency acronym MINECO
Program Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Call Proyectos I+D+i Retos de Investigación
Call year 2013
State Plan 2013-2016 Plan Estatal de Investigación Científica y Técnica y de Innovación
Management unit Secretaría de Estado de Educación, Formación Profesional y Universidades
Beneficiary centre AGENCIA ESTATAL CONSEJO SUPERIOR DE INVESTIGACIONES CIENTIFICAS (CSIC)

Resultados relacionados

Resultados totales (Incluyendo duplicados): 31
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Evaluation of sol-gel TiO2 photocatalysts modified with carbon or boron compounds and crystallized in nitrogen or air atmospheres

  • Ansón-Casaos, Alejandro
  • Sampaio, Maria Jose
  • Jarauta-Córdoba, Clara
  • Martínez Fernández de Landa, María Teresa
  • Silva, Cláudia
  • Faria, Joaquim L.
  • Silva, Adrián M. T.
Sol-gel TiO2 photocatalysts are synthesized from titanium isopropoxide and crystallized by thermal treatment under either air atmosphere or nitrogen flow. Reference TiO2 photocatalysts crystallized at 550 ºC for 30 min in air are the most active for the degradation of diphenhydramine pharmaceutical (DPH). In addition, TiO2 precursors are modified with carbon or boron compounds. The highest rates of conversion are obtained in the case of TiO2 modified with boric acid and crystallized in air. The sol-gel photocatalysts with the best performances possess anatase:rutile phase ratios in excess of 95% with anatase crystallites of approximately 60 nm. The photocatalysts are characterized by different solid state and solution techniques, including powder X-ray diffraction, elemental analysis, X-ray photoelectron spectroscopy, Fourier-transform infrared spectroscopy, diffuse reflectance ultraviolet-visible (UV-Vis), UV-Vis liquid spectroscopy, surface area analysis and ammonia thermal programmed desorption. The efficiencies of the synthetized photocatalysts are characterized by the kinetics of DPH degradation under near UV-Vis irradiation. The efficiencies of the synthetized photocatalysts are comparable or even higher than that of the reference P25, although their dispersions in water have much lower absorbance values., This work was funded by the Spanish Ministry MINECO and the European Regional Development Fund under the projects PRI-PIBAR-2011-1 and ENE2013-48816-C5-5-R, and the Government of Aragon (DGA) and the European Social Fund (DGA-ESF-T66 Grupo Consolidado). This work was partially supported by Project PEst-C/EQB/LA0020/2013, financed by FEDER through COMPETE – Programa Operacional Factores de Competitividade, and by FCT – Fundação para a Ciência e a Tecnologia, and co-financed by QREN, ON2 and FEDER (Project NORTE-07-0124-FEDER-000015). FCT is acknowledged for funding the doctoral grant SFRH/BD/79878/2011 (MJS). AMTS acknowledges the FCT Investigator 2013 Programme (IF/01501/2013), with financing from the European Social Fund and the Human Potential Operational Programme., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Contribución de congreso (ConferenceOutput)

Carbon nanostructured materials for energy applications, Materiales nanoestructurados de carbono para aplicaciones en energía

  • Ansón-Casaos, Alejandro
  • Martínez Fernández de Landa, María Teresa
Work presented at the meeting IBERNAM-CMC2. November 20-21, 2014, Naturgas Energía, Bilbao, Spain, This work was funded by the Spanish Ministry MINECO and the European Regional Development Fund under the projects PRI-PIBAR-2011-1 and ENE2013-48816-C5-5-R, and the Government of Aragon (DGA) and the European Social Fund (DGA-ESF-T66 Grupo Consolidado)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Carbon nanotube-supported gold nanoparticles as efficient catalyst for the selective hydrogenation of nitroaromatic derivatives to anilines

  • Cano, Manoli
  • Villuendas, Pedro
  • Benito, Ana M.
  • Urriolabeitia, Esteban P.
  • Maser, Wolfgang K.
Gold nanoparticles (AuNPs) with sizes between 3 and 10 nm were firmly supported on pristine multi-walled carbon nanotubes (MWCNT) in high yields by a facile linker-free deposition route using aqueous suspensions of pre-reduced gold precursors. For the first time, the resulting AuNP-MWCNT hybrid material was employed as catalyst for the hydrogenation of a series of substituted nitroarenes under mild reaction conditions. High catalytic activity with turnover frequencies (TOF) values up to 1200 h-1 were achieved accompanied by a remarkable chemoselectivity. Recyclability tests did neither reveal leaching nor changes in size or oxidation states of the AuNPs. The concomitant presence of Au0 and AuI accounts for both the superior catalytic performance and the high stability of the hybrid material. Preferential orientation of nitroarenes on the MWCNT surface due to π-π interactions coupled with coulombic contact of the nitro group to the AuNPs most likely explains the high chemoselectivity of the hybrid material, and further underlines the valuable role of MWCNTs for catalytic reactions., Financial support from Spanish MINECO and the European Regional Development Fund (projects MAT2010-15026, ENE2013-48816-C5-5-R and CTQ2011-22589), Spanish National Research Council CSIC (project 201080E124), and Regional Government of Aragon and the European Social Fund DGA-ESF (T66 Grupo Consolidado, E-97, and E-26) is gratefully acknowledged., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Self-assembled graphene aerogel and nanodiamond hybrids as high performance catalysts in oxidative propane dehydrogenation

  • Roldán, Laura
  • Benito, Ana M.
  • García-Bordejé, José Enrique
Graphene aerogels and graphene aerogel–nanodiamond hybrids have been fabricated by a mild reduction/self-assembly hydrothermal method using graphene oxide dispersion as a precursor. The aerogels have been used as metal-free catalysts for oxidative dehydrogenation of propane. Reduced graphene oxide (RGO) aerogels without nanodiamonds outperformed carbon nanotubes in terms of propene productivity and selectivity, which is correlated with a higher content of accessible carbonyl–quinone groups and more defective structures of reduced graphene oxide. Graphene aerogels loaded with low amounts of nanodiamonds (2 wt%) by a one-pot strategy provided 18% higher activity than RGO aerogels, ascribed to the increase of the sp3/sp2 ratio. For nanodiamond contents higher than 2 wt%, the productivity and selectivity drops, which can be explained by a dramatic decrease of carbonyl–quinone groups, an increased content of unselective oxygen species and clustering of nanodiamonds for the highest loadings. Hybrid aerogels are freestanding, robust and highly porous monoliths; thereby a suitable platform to be used as catalysts or adsorbents in flow systems., The financial support of European Commission (FREECATS project, FP7 Grant agreement nº 280658), from Spanish Ministry MINECO and the European The financial support from European Commission (FREECATS project, FP7 Grant agreement no. 280658), Spanish Ministry MINECO and the European Regional Development Fund (project ENE2013-48816-C5-5-R), and Regional Government of Aragon (DGA-ESF-T66 Grupo Consolidado) are gratefully acknowledged., Sí
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

In-vitro toxicity of carbon nanotube/polylysine colloids to colon cancer cells

  • Ansón-Casaos, Alejandro
  • Grasa, Laura
  • Pereboom, Desirée
  • Mesonero, José Emilio
  • Casanova, Álvaro
  • Murillo, María Divina
  • Martínez Fernández de Landa, María Teresa
Single-walled carbon nanotubes (SWCNTs) are thoroughly purified and dispersed in an aqueous solution of high molecular weight poly-L-lysine (pLlys). Human intestinal epithelial Caco-2/TC7 cells are incubated with the SWCNT dispersions in pLlys, and their effects on cell viability are studied by image flow cytometry. No significant changes are observed in the cell culture wells up to pLlys concentrations of 10 g mL-1. However, high mortality is detected at pLlys concentrations of 100 g mL-1. The presence of oxygen-free SWCNTs does not modify the effects of pLlys on cell cultures at any of the tested concentrations (£ 1 g mL-1). In addition, SWCNTs having an 8 wt.% of surface oxygen are tested with identical results. Thus, purified SWCNTs, even bearing oxygen functional groups, act as inert particles in the cell culture medium. This result supports the applicability of SWCNTs as carriers in pharmacological formulations against digestive tract diseases., This work was funded by the Spanish Ministry MINECO and the European Regional Development Fund under the projects PRI-PIBAR-2011-1 and ENE2013-48816-C5-5-R, and the Government of Aragon and the European Social Fund (DGA-ESF-T66 Grupo Consolidado and DGA-ESF-B61 Grupo Consolidado)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Origin of the excellent performance of Ru on nitrogen-doped carbon nanofibers for CO2 hydrogenation to CH4

  • Roldán, Laura
  • Marco, Yanila
  • García-Bordejé, José Enrique
Carbon materials have rarely been used as support for CO2 methanation, which is usually carried out using catalysts supported on metal oxides. Here, it is shown that Ru nanoparticles supported on nitrogen-doped carbon nanofibers (NCNF) provide competitive CH4 production rate and stability compared to Al2O3-supported catalysts. Contrary to the general belief about the inert nature of carbon supports, it is demonstrated that NCNF is a non-innocent spectator in CO2 methanation due to its ability to store a high amount of COad reaction intermediates. This explains the excellent catalytic behaviour afforded by this unconventional catalyst support., The financial support of European Commission (FREECATS project, FP7 Grant agreement nº 280658), from Spanish Ministry MINECO and the European Regional Development Fund (project ENE2013-48816-C5-5-R), and Regional Government of Aragon (DGA-ESF-T66 Grupo Consolidado) are gratefully acknowledged., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Graphene oxide-carbon nanotube hybrid assemblies: Cooperatively strengthened OH···O=C hydrogen bonds and removal of chemisorbed water

  • Núñez, Jesús David
  • Benito, Ana M.
  • Rouzière, Stéphan
  • Launois, Pascale
  • Arenal, Raúl
  • Ajayan, Pulickel M.
  • Maser, Wolfgang K.
6 Figuras, Owing to their great interest for energy storage and sensing applications, multi-layer papers consisting of graphene oxide – carbon nanotube (GO-CNT) hybrid sheets were prepared by in-situ exfoliation of graphite oxide in the presence of oxidized CNTs (oCNTs). For the first time we elucidate the influence of oCNTs on chemisorbed water (CW), i.e. water molecules inherently bound to oxygen functional groups (OFGs) of graphene oxide (GO) and responsible for irreversible structural damage upon thermal reduction processes. We show that oCNTs self-assemble onto GO sheets during the liquid phase processing steps by forming cooperatively strengthened OH···O=C hydrogen bonds between the carboxylic groups of oCNTs and OFGs of GO. At oCNT contents of about 10 to 15 wt. % this leads to the displacement of considerable amounts of CW without altering the original chemical composition of GO. Thermally reduced GO-CNT (rGO-CNT) papers reveal improved sp2 character and an enhancement of the specific capacitance by 75% with respect to thermally reduced GO (rGO), largely due to the effective removal of CW by oxidized CNTs. These findings disclose the relevance of cooperative hydrogen bonding phenomena in graphene oxide paper/film electrodes for the development of improved electrochemical energy storage and sensing devices., JDN is thankful for his CSIC PhD grant JAEPre09-01155 covering also his research stay at Rice University. WKM and AMB acknowledge financial support from Spanish MINECO and the European Regional Development Fund through project grants ENE2013-48816-C5-5-R, ENE2016-79282-C5-1-R and the Government of Aragon and the European Social Fund under project DGA-FSE-T66 CNN. RA gratefully acknowledges the support from MINECO through project grants FIS2013-46159- C3-3-P and MAT2016-79776-P. Some of the research has received funding from the European Union FP7 program under Grant Agreement 312483 ESTEEM2 (Integrated Infrastructure Initiative – I3) and from the European Union H2020 program under the grant 696656 Graphene Flagship, and H2020 Marie Skłodowska-Curie grant 642742., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Contribución de congreso (ConferenceOutput)

Synthesis and dispersion of reduced graphene oxide used for thin film electrodes in organic photovoltaics

  • Víctor-Román, Sandra
  • Sanahuja-Parejo, Olga
  • Lira-Cantú, Mónica
  • Ansón-Casaos, Alejandro
  • García-Bordejé, José Enrique
  • Benito, Ana M.
  • Maser, Wolfgang K.
Resumen del póster presentado al International meeting on the chemistry of graphene and carbon nanotubes, celebrado en Bruselas (Bélgica) del 3 al 7 de abril de 2016., Graphene oxide, with its ease of synthesis and possibilities for functionalization, reduction, tailoring electronic properties coupled to favorable thin film processing strategies, has attracted increased interest in the field organic photovoltaics. It has been used as transparent electrode layer, active layer, electron and hole transporter layer, and interfacial layer6, contributing to enhanced performance of organic solar cells. Operational functionality critically depends on the parent graphene oxide, the applied reduction processes and functionalization strategies, dispersions, and thin film processing techniques. Here we present a first study on the preparation of graphene oxide with different degrees of reduction, the elaboration of corresponding dispersions and their processing into the films for obtaining solar cells. Reflux processing using different times of reduction was employed. Thin films were prepared using automatic spray and spin coating techniques. Dispersion, thin films and solar cell were characterized by UV-Vis spectroscopy, zeta potential, optical microscopy, TPD and electrical conductivity measurements., Funding by Spanish Ministry MINECO and European Regional Development Fund (ENE2013-48816-C5-5-R “NANOSOL-MAT”, and PhD Grant BES 2014-068727), Government of Aragón and European Social Fund (DGAESF-T66 “Grupo Consolidado”) is acknowledged., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Mesoporous carbon doped with N,S heteroatoms prepared by one-pot auto-assembly of molecular precursor for electrocatalytic hydrogen peroxide synthesis

  • Roldán, Laura
  • Truong-Phuocb, Lai
  • Ansón-Casaos, Alejandro
  • García-Bordejé, José Enrique
A bottom-up approach based on hydrothermal carbonization of organic molecules has been used to prepare carbon materials doped with either nitrogen or sulfur or both. To generate mesopores, ZnCl2 has been used as removable structure-directing agent. The final mean pore size depended on the type of dopant element. The doped materials exhibited remarkable activity as electrocatalyst in oxygen reduction reaction with nearly complete selectivity to H2O2 synthesis. N-doped catalyst with an intermediate nitrogen content (4 wt%) and around 80% of pore volume in the mesopore range provided significantly better performance than a catalyst of comparable composition but differing in the porous structure, i.e. 70 % of pore volume in the microporous range., The financial support of European Commission (FREECATS project, FP7 Grant agreement nº 280658), from Spanish Ministry MINECO and the European Regional Development Fund (project ENE2013-48816-C5-5-R), and Regional Government of Aragon (DGA-ESF-T66 Grupo Consolidado) are gratefully acknowledged., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Cysteine functionalized bio-nanomaterial for the affinity sensing of Pb(II) as an indicator of environmental damage

  • Ramírez, María L.
  • Tettamanti, Cecilia S.
  • Gutiérrez, Fabiana A.
  • González Domínguez, José Miguel
  • Ansón-Casaos, Alejandro
  • Hernández-Ferrer, Javier
  • Martínez Fernández de Landa, María Teresa
  • Rivas, Gustavo A.
  • Rodríguez, Marcela C.
This work aims at the development of an electrochemical affinity biosensor for Pb(II) quantification using a platform that combines glassy carbon electrodes (GCE) and an aqueous dispersion of single-walled carbon nanotubes (SWCNT) covalently modified with cysteine residues (Cys). The biosensing protocol includes the accumulation of Pb(II) at the electrode surface through the affinity interaction promoted by Cys residues at open circuit potential, followed by the reduction of the accumulated Pb(II) at ‐0.900 V and the transduction step performed by linear sweep-adsorptive stripping voltammetry (LSAdSV) in a 0.020 M acetate buffer solution pH 5.00. There is a linear relationship between Pb(II) oxidation peak current and Pb(II) concentration. The dynamic linear range extends from 5.0 to 125.0 μg·L−1, exhibiting a sensitivity of 0.061 μAμg−1L and a detection limit of 0.69 μg·L−1. In addition, the selectivity of the biosensor was evaluated in the presence of high concentrations of possible interferents such as Cu(II), Cd(II), Ni(II), Hg(II), Rh(II), Ru(II), Zn(II), Ir(IV), Co(II) and As(III) demonstrating a high discrimination of Pb(II) in complex samples. The sensor was challenged with tap and rain water samples enriched with Pb(II), demonstrating outstanding properties in terms of recovery percentages showing an excellent agreement with ICP- MS., The authors are grateful to CONICET (PIP 2015 Project N° 11220150100710CO), SECyT-UNC (PID Project 2016-2017 SIGEVA N° 30720150101013CB), ANPCyT (Projects : PICT 2013 N° 2817, PICT 2015 N° 0077) and MINCyT-Córdoba (PID Project N° 000018/2014), Spanish Ministry of Economy and Competitiveness (MINECO) project ENE2013-48816-C5-5-R, and the Government of Aragon and the European Social Fund under project grant DGA-FSE-T66 CNN for the financial support given to this work. M.L.R. and C.S.T. acknowledge doctoral fellowships from CONICET., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Parametric study of the hydrothermal carbonization of cellulose and effect of acidic conditions

  • García-Bordejé, José Enrique
  • Pires, Elísabet
  • Fraile, José M.
Microcrystalline cellulose has been used to develop carbonaceous materials by hydrothermal synthesis. The use of HCl in different concentrations modifies the nature of the obtained materials. Surface area, determined by CO2 adsorption, can be used to define a new empirical parameter, the “hydrothermal index” (H.I.), which allows a simple comparison of the different hydrothermal conditions. Higher temperature, longer time and higher HCl concentration produce, at the beginning, an increase in surface area up to a maximum of 386 m2/g, whereas harsher conditions beyond this limit decrease the surface area up to values around 100 m2/g. Carbon and oxygen content of the hydrothermal carbons nicely correlate with this hydrothermal index. However, the HCl concentration affects more directly to other properties, such as the particle size and morphology, the carbon yield, or the distribution of functional groups. This is due to the co-existence of at least two hydrothermal pathways, one in solution after cellulose hydrolysis and another one in solid phase. The prevalence of one mechanism or another depends on the variations in the individual rates of the reactions involved in the hydrothermal process., This work was made possible by the financial support of the Spanish Ministerio de Economía y Competitividad (projects CTQ2014-52367-R and ENE2013-48816-C5-5-R) and the Gobierno de Aragón (E11 Group co-financed by the European Regional Development Funds)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Functionalization of silver nanowire transparent electrodes with self-assembled 2-Dimensional tectomer nanosheets

  • Jurewicz, Izabela
  • Garriga, Rosa
  • Large, Matthew J.
  • Burn, Jake
  • Bardi, Niki
  • King, Alice A. K.
  • Velliou, Eirini G.
  • Watts, John F.
  • Hinder, Steven J.
  • Muñoz, Edgar
  • Dalton, Alan B.
9 Figuras.-- Información complementaria disponible en línea en la página web del editor.-- This document is the unedited Author’s version of a Submitted Work that was subsequently accepted for publication in ACS Applied Nano Materials 1,8, 3903-3912 (2018), copyright © American Chemical Society after peer review. To access the final edited and published work see http://dx.doi.org/10.1021/acsanm.8b00689, Here, we describe the unusual self-assembly of amine-terminated oligoglycine peptides into extended two-dimensional sheets in the presence of silver nanowires. The resulting tectomer sheets are shown to have a strong affinity for the nanowires through a charge-transfer interaction as evidenced by X-ray photoelectron spectroscopy. We show that extended assemblies of metal–peptide hybrids offer additional augmentative functionalities; for instance, the tectomer sheets are hydrophobic in nature and act as a protective layer preventing oxidation and degradation of the nanowires when exposed to atmospheric conditions. Moreover, for silver nanowire percolating networks the presence of the peptide markedly increases the overall electrical conductivity through mechanical squeezing of wire–wire junctions in the network. The peptide–metal interface can be controlled by pH stimulus thus potentially offering new directions where silver nanowire assemblies are used for transparent electrodes ranging from antimicrobial coatings to biosensors., This work was supported by Grant EP/K031562 from the Engineering and Physical Sciences Research Council (EPSRC), ENE2013-48816-C5-5-R project (Plan Nacional de I+D+I, from Spanish Ministerio de Economía y Competitividad MINECO), and H2020-MSCA-ITN-2014 Enabling Excellence project., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Intercalated water in multi-layered graphene oxide paper: an X-ray scattering study

  • Rouzière, Stéphan
  • Núñez, Jesús David
  • Paineau, Erwan
  • Benito, Ana M.
  • Maser, Wolfgang K.
  • Launois, Pascale
X-ray scattering (XRS) experiments have been performed on multi-layered graphene oxide (GO) paper. GO can be easily hydrated as water naturally intercalates in the hydro­philic nanostructure. The effect of the intercalated water on the XRS signals is measured during dehydration under thermal treatment in the temperature range 298–473 K as well as during hydration under saturated water vapour pressure. A simple modelling of the XRS signals by taking into account the presence and the type of intercalated water (bound water or physisorbed water) is introduced. It allows an explanation of the variations of intensity and position of XRS reflections observed experimentally., EP, SR and PL benefited of a grant from the French Research National Agency under the program Investissements d’Avenir (SEDECO project, ANR-10-LABX-0035: Labex NanoSa-clay). AMB and WKM acknowledge funding from the Spanish Ministry MINECO under projects ENE2013-48816-C5-5-R and ENE2016-79282-C5-1-R with their associated European Regional Development Funds, and from the Government of Aragon under Consolidated Group programme DGA-T66-GCNN and the associated European Social Fund., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Contribución de congreso (ConferenceOutput)

Preparation and characterization of poly(3-hexyl thiophene) nanoparticles and graphene oxide composites in water

  • Istif, Emin
  • Hernández-Ferrer, Javier
  • Urriolabeitia, Esteban P.
  • Tagmatarchis, Nikos
  • Benito, Ana M.
  • Maser, Wolfgang K.
Resumen del póster presentado a la 9th Stuttgart Nanodays Conference, celebrada en Munich (Alemania) del 13 al 15 de septiembre de 2017., Funding by EU (Project H2020-ITN 2014 642742), Spanish MINECO (ENE2013-48816-C5-5-R) and Government of Aragon (DGA-ESF-T66), is gratefully acknowledged., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Contribución de congreso (ConferenceOutput)

Structural elucidation and comparison of fluorescent carbon dots

  • Vallan, Lorenzo
  • Benito, Ana M.
  • Martínez Fernández de Landa, María Teresa
  • Urriolabeitia, Esteban P.
  • Maser, Wolfgang K.
Resumen del póster presentado a la 9th Stuttgart Nanodays Conference, celebrada en Munich (Alemania) del 13 al 15 de septiembre de 2017., Funding by EU (Project H2020-ITN 2014 642742), Spanish MINECO (ENE2013-48816-C5-5-R) and Government of Aragon (DGA-ESF-T66), is gratefully acknowledged., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Single-walled carbon nanotubes covalently functionalized with cysteine: A new alternative for the highly sensitive and selective Cd(II) quantification

  • Gutiérrez, Fabiana A.
  • González Domínguez, José Miguel
  • Ansón-Casaos, Alejandro
  • Hernández-Ferrer, Javier
  • Rubianes, María R.
  • Martínez Fernández de Landa, María Teresa
  • Rivas, Gustavo A.
7 Figuras.- 3 Tablas, This work is focused on the development of an electrochemical sensor for the quantification of Cd(II) based on the use of glassy carbon electrodes (GCE) modified with a dispersion of single-walled carbon nanotubes (SWCNTs) covalently functionalized with cysteine (Cys). Cd(II) is preconcentrated at the electrode surface by complex formation at open circuit potential, followed by the reduction at ∧0.900 V and the final anodic voltammetric stripping in a 0.020 M acetate buffer solution pH 5.00. The functionalization of SWCNTs was performed through the reaction between the carboxylic groups of oxidized SWCNT and amino groups of S-triphenylmethyl cysteine using a coupling chemistry agent based on benzotriazol for the activation of carboxylic residues. There was a linear relationship between Cd oxidation signal and Cd(II) concentration between 1.0 and 300.0 α/4gL∧1 Cd(II), with a sensitivity of (49 ± 2) í 10∧3 α/4Aα/4g∧1L and a detection limit of 0.3 α/4gL∧1. The reproducibility was 1.7% using the same dispersion and 3.8% using 3 different dispersions. The sensor was challenged with groundwater samples enriched with Cd(II) showing excellent recovery percentages and excellent agreement with the values obtained by ICP-MS., The authors thank CONICET, SECyT-UNC, ANPCyT, MINCyT-Córdoba, Spanish Ministry of Economy and Competitiveness (MINECO) project ENE2013-48816-C5-5-R, and the Government of Aragon and the European Social Fund under project grant DGA-FSE-T66 CNN for the financial support., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

The effect of the thermal reduction on the kinetics of low-temperature 4He sorption and the structural characteristics of graphene oxide

  • Dolbin, A. V.
  • Khlistyuck, M. V.
  • Esel'son, V. B.
  • Gavrilko, V. G.
  • Vinnikov, N. A.
  • Basnukaeva, R. M.
  • Prokhvatilov, Anatolii
  • Meleshko, Volodymyr
  • Benito, Ana M.
  • Maser, Wolfgang K.
This article may be downloaded for personal use only. Any other use requires prior permission of the author and AIP Publishing. This article appeared in Low Temperature Physics 43, 383 (2017) and may be found at https://doi.org/10.1063/1.4979362, The kinetics of the sorption and the subsequent desorption of 4He by the starting graphite oxide (GtO) and the thermally reduced graphene oxide samples (TRGO, Treduction = 200, 300, 500, 700 and 900 °C) have been investigated in the temperature interval 1.5–20 K. The effect of the annealing temperature on the structural characteristics of the samples was examined by the x-ray diffraction (XRD) technique. On lowering the temperature from 20 to 11–12 K, the time of 4He sorption increased for all the samples, which is typically observed under the condition of thermally activated diffusion. Below 5 K the characteristic times of 4He sorption by the GtO and TRGO-200 samples were only weakly dependent on temperature, suggesting the dominance of the tunnel mechanism. In the same region (T < 5 K) the characteristic times of the TRGOs reduced at higher temperatures (300, 500, 700 and 900 °C) were growing with lowering temperature, presumably due to the defects generated in the carbon planes on removing the oxygen functional groups (oFGs). The estimates of the activation energy (Ea) of 4He diffusion show that in the TRGO-200 sample the Ea value is 2.9 times lower as compared to the parent GtO, which is accounted for by GtO exfoliation due to evaporation of the water intercalated in the interlayer space of carbon. The nonmonotonic dependences Ea(T) for the GtO samples treated above 200 °C are determined by a competition between two processes—the recovery of the graphite carbon structure, which increases the activation energy, and the generation of defects, which decreases the activation energy by opening additional surface areas and ways for sorption. The dependence of the activation energy on Treduction correlates well with the contents of the crystalline phase in GtO varying with a rise of the annealing temperature., Financial support from Spanish Ministry MINECO and the European Regional Development Fund (Project No. ENE2013-48816-C5-5-R), the Regional Government of Aragon and the European Social Fund DGA-ESF (Project No. T66) and Targeted Comprehensive Fundamental Research Program of NASU (Project No. 6/16-H) is gratefully acknowledged., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Function of the support and metal loading on catalytic carbon dioxide reduction using ruthenium nanoparticles supported on carbon nanofibers

  • Roldán, Laura
  • Marco, Yanila
  • García-Bordejé, José Enrique
8 Figuras, 3 Tablas.-- Información suplementaria disponible en línea en la página web del editor., Catalytic CO2 reduction has been performed using carbon nanofibers or nitrogen‐doped carbon nanofibers as a support for Ru nanoparticles. The catalyst that consists of 5 wt % Ru on nitrogen‐doped carbon nanofibers exhibited the highest conversion at a relatively low temperature, complete selectivity to CH4, and stable catalytic performance. The catalytic performance was substantially superior to catalysts supported on carbon nanotubes and akin to the best metal‐oxide‐supported catalyst in the literature. The characterization of the prepared catalyst by transient experiments (CO2 temperature‐programmed desorption, temperature‐programmed surface reaction, and transient response to CO2 removal) revealed that the catalyst support participates actively in the reaction. The Ru content governed the selectivity, which either favored CO formation for lower Ru contents (0.5–2 wt %) or CH4 formation for 5 wt % Ru loading. The mean Ru particle size determined by TEM was similar for each of the metal loadings. Therefore, the substantially different selectivity patterns cannot be attributed to structure sensitivity. The higher selectivity to CH4 can be explained by the enhanced supply of adsorbed hydrogen to the activated adsorbed CO intermediate, which was demonstrated to be the rate‐determining step., The financial support of the European Commission (FREECATS project, FP7 Grant agreement number 280658), the Spanish Ministry MINECO and the European Regional Development Fund (project ENE2013‐48816‐C5‐5‐R), and the Regional Government of Aragon (DGA‐ESF‐T66 Grupo Consolidado) is gratefully acknowledged., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

The viscosity of dilute carbon nanotube (1D) and graphene oxide (2D) nanofluids

  • Ansón-Casaos, Alejandro
  • Ciria, José Carlos
  • Sanahuja-Parejo, Olga
  • Víctor-Román, Sandra
  • González Domínguez, José Miguel
  • García-Bordejé, José Enrique
  • Benito, Ana M.
  • Maser, Wolfgang K.
5 Tablas, 7 Figuras.-- Material suplementario disponible en línea en la página web del editor., Controlling the physicochemical properties of nanoparticles in fluids directly impacts on their liquid phase processing and applications in nanofluidics, thermal engineering, biomedicine and printed electronics. In this work, the temperature dependent viscosity of various aqueous nanofluids containing carbon nanotubes (CNTs) or graphene oxide (GO), i.e. 1D and 2D nanoparticles with extreme aspect ratios, is analyzed by empirical and predictive physical models. The focus is to understand how the nanoparticle shape, concentration, motion degrees and surface chemistry affect the viscosity of diluted dispersions. To this end, experimental results from capillary viscosimeters are first examined in terms of the energy of viscous flow and the maximum packing fraction applying the Maron-Pierce model. Next, a comparison of the experimental data with predictive physical models is carried out in terms of nanoparticle characteristics that affect the viscosity of the fluid, mostly their aspect ratio. The analysis of intrinsic viscosity data leads to a general understanding of motion modes for carbon nanoparticles, including those with extreme aspect ratios, in a flowing liquid. The resulting universal curve might be extended to the prediction of the viscosity for any kind of 1D and 2D nanoparticles in dilute suspensions., This work has been funded by the Spanish MINEICO under the project ENE 2016-79282-C5-1-R (AEI/FEDER, UE), the Government of Aragón (Grupo reconocido T03-20R) and associated EU Regional Development Funds (DGA/FEDER, UE). SVR thanks Spanish MINEICO for her PhD grant (BES2014-068727 and associated EU Social Funds). J.M.G.-D. greatly acknowledges Spanish Ministry of Science, Innovation and Universities (MICINN, formerly MINEICO) for his “Juan de la Cierva – incorporación” grant (Ref. JCI-2016-27789). We also acknowledge institutional support from the Unit of Information Resources for Research at the "Consejo Superior de Investigaciones Científicas" (CSIC) for the article-processing charges contribution., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Contribución de congreso (ConferenceOutput)

Nanostructured complexes of conducting polymers and graphene oxide

  • Istif, Emin
  • Vallan, Lorenzo
  • Benito, Ana M.
  • Maser, Wolfgang K.
1 figure.-- Talk delivered at the 9th Nanodays Workshop on Advanced Materials, Munich (Germany), Sept. 13-15, 2017, Intrinsically conducting polymers form the base for the development of plastic electronic devices and hold great promise in optoelectronic applications such as thin film organic field-effect transitors, OLEDS and solar cells. Control of morphology and aggregation states by nanostructuring is essential for improving the device performance. In the last decade, research has focused on liquid phase assembly processes. These afford conjugated polymers in the form of nanoparticles or nanowires, which are dispersible in aqueous dispersions and allow for the fabrication of thin films with well-defined characteristics from environmentally-friendly solutions. Moreover, the liquid phase self-assembly processes provide unique opportunities for the development of novel composite materials with graphene based materials [1, 2]. Here we present our results of our recent work on the development of novel composite materials based of graphene oxide and poly (3-hexylthiophene) (P3HT) [3]. We show that liquid phase assembly processes in the presence of water-soluble graphene oxide sheets lead to the formation P3HT nanoparticles (P3HTNPs) in intimate contact with surrounding sheets of graphene oxide. During the synthesis, graphene oxide acts as a >good> solvent and induces important changes on the internal aggregation structure and the related interchain coupling. At the same time, the charge-transfer properties as a function of GO concentration are modified. Both effects are intimately coupled and lead to the stabilization of of P3HTNPs-GO donor-acceptor nanostructures offering improved charge transport and charge separation characteristics in thin films., Funding by EU (Project H2020-ITN 2014 642742), Spanish MINECO (ENE2013-48816-C5-5-R) and Government of Aragon (DGA-ESF-T66), is gratefully acknowledged.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Contribución de congreso (ConferenceOutput)

Separación de nanotubos de carbono en metálicos y semiconductores: Análisis espectroscópico en medio disperso

  • Santidrián, Ana
  • Rubio-Muñoz, Cristina
  • Ansón-Casaos, Alejandro
  • Martínez Fernández de Landa, María Teresa
  • Benito, Ana M.
  • Maser, Wolfgang K.
2 figuras.-- Presentado en el Encuentro anual IberNAM 2015, "Empresas de Base Tecnológica en Micro-Nanosistemas: experiencias y oportunidades de colaboración”, Zaragoza, (España), 10-11 Diciembre 2015., El uso de gel para cromatografía, como Sephacryl, ha demostrado ser un método eficaz para separar nanotubos metálicos y semiconductores cuando la heterogénea muestra de partida de nanotubos de carbono es dispersada en surfactantes como el SDS. En el presente estudio se analizan las fracciones obtenidas por este método de separación por métodos espectroscópicos., Este trabajo ha sido financiado por el MINECO, el CSIC (proyecto intramural 2015801011), el Fondo Europeo de Desarrollo Regional (ENE2013-48816-C5-5-R), el Gobierno de Aragón, el Fondo Social Europeo (DGA-ESF-T66 Grupo Consolidado) y la Comisión Europea (H2020-MSCA-ITN-2014-ETNSEP-210139683 642742).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Contribución de congreso (ConferenceOutput)

Bifunctional mechanism of CO2 reduction to CH4 on Ru nanoparticles supported on carbon nanomaterials

  • Roldán, Laura
  • Marco, Yanila
  • García-Bordejé, José Enrique
2 figures.--Work presented at The 7th International Symposium on Carbon for Catalysis, CarboCat VII, "New carbon-based catalytic systems", 12th-17th June 2016, Strasbourg (France)., Renewable energies are one of the energetic solutions for the future, due to the limitation and environmental risk of fossil fuels. Nevertheless, the production of energy from renewable sources is intermittent and is produced far from the places where it is consumed. Therefore, it is urgent developing ways for the storage and transport of this energy. A solution is the conversion of renewable energy in the energetic vector H2. The main problem is its storage and transport since the typical discharge time in the current infrastructures is less than 100 hours.When long time storage is needed, one option is the conversion of H2 with CO2 in synthetic natural gas (CH4), which can be stored in the current infrastructures without limitation. Moreover, if the used CO2 have been previously captured in a power station, it contributes to greenhouse gas abatement. The reaction between CO2 con H2 was discovered more than a century ago. Different transition metal and noble metal supported on different metallic oxides have been used as catalyst. Up to our knowledge, carbon nanomaterials have not been used as catalyst support in this reaction. In fact, there are some reports that CNT are inactive for this reaction, which is attributed to the inertness of the support to chemisorb CO2. Herein, we have supported Ru nanoparticles on carbon nanotubes (CNTs), carbon nanofibers (CNFs) and Nitrogen doped carbon nanofibers (N-CNF). Several Ru loadings (0.5, 2 y 5 wt%) were deposited on CNF and N-CNF by wet impregnation of (Ru(NO)(NO3)). 50 mg of catalyst diluted with SiC was placed in a quartz reactor, reduced at 425 K in H2 and tested at different temperatures with a feed of 60 ml/min of 5 % CO2, 15 % H2 and Ar to balance. The outlet gases were analysed using a Pfeifer mass spectrometer., Aknowledgements. The authors are indebted to the funding of European Commission (FREECATS project, grant agreement No. 280658), MINECO and FEDER (project ENE2013-48816-C5-5-R) and the regional Aragón Government (DGA-ESF-T66 Grupo Consolidado).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Contribución de congreso (ConferenceOutput)

Carbon nanotubes meet graphene oxide: Efficient removal of chemisorbed water for enhanced electrode materials

  • Maser, Wolfgang K.
  • Benito, Ana M.
  • Núñez, Jesús David
  • Rouzière, Stéphan
  • Launois, Pascale
  • Arenal, Raúl
  • Ajayan, Pulickel M.
Work presented at the 1st Workshop "Carbon Nanotubes Meet 2-Dimensional Materials", 2nd-4th November, 2016, Ruprecht Karls Universitat Heidelberg (Germany), Self-assembled graphene oxide (GO) papers are of increased interest for filtration, sensing and energy storage applications . The performance of the paper assemblies, especially upon thermal reduction treatments, is seriously affected by the presence of chemisorbed water, i.e. water molecules inherently bound to the oxygen functional groups (OFGs) of GO. In this work we show that oxidized multiwall carbon nanotubes (oCNTs) self-assembled onto GO sheets by an in-situ exfoliation process effectively can remove chemisorbed water and significantly reduce associated damaging effects., Funding by Spanish Ministry MINECO and European Regional Development Fund (Project ENE2013-48816-C5-5-R), the Government of Aragon and the European Social Fund (ProjectDGA-ESF-T66), and the EU (Project H2020-ITN 2014 642742) is gratefully acknowledged.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Transparent conducting films made of different carbon nanotubes, processed carbon nanotubes, and graphene nanoribbons

  • Ansón-Casaos, Alejandro
  • Mis Fernández, Ricardo
  • López-Alled, Carlos M.
  • Almendro López, Eduardo
  • Hernández-Ferrer, Javier
  • González Domínguez, José Miguel
  • Martínez Fernández de Landa, María Teresa
Transparent conducting films (TCFs) are made of different single-walled (SW) or multi-walled (MW) carbon nanotubes (CNTs), some of them previously modified by chemical or physical processes. The TCFs are prepared by spray-coating of CNT surfactant dispersions over glass substrates. Among pristine CNTs, laser-grown SWCNTs lead to the lowest resistivity, even though good results can be achieved with other selected SW or MWCNTs. Ultracentrifugation of the SWCNT dispersions can be utilized for improving the characteristic SWCNT spectroscopic signals. Controlled oxidation, acid treatment, and covalent functionalization with aromatic organic groups can be applied to CNT solid powders without substantially increasing the resulting TCF resistivity. The oxidative transformation of arc-discharge MWCNTs into graphene nanoribbons relatively improves their TCF performance. The positive effects of TCF washing with water or oxidant acids are quantified for various SWCNT types. Red and green inks, enriched in metallic or semiconducting SWCNTs, are obtained by the gel-chromatographic method, all the fractions being useful for the preparation of TCFs. Thus, it is shown that different physical and chemical processes can be performed on CNTs before or after their deposition, demonstrating a great chemical versatility for CNT-TCFs., This work has been funded by the Spanish Ministry MINECO and the European Regional Development Fund under the projects TEC2010-15736, PRI-PIBAR-2011-1 and ENE2013-48816-C5-5-R, and the Government of Aragon and the European Social Fund (DGA-ESF-T66 Grupo Consolidado)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Contribución de congreso (ConferenceOutput)

Electron conduction and trapping in single-walled carbon nanotubes sorted by gel chromatography

  • Ansón-Casaos, Alejandro
  • Rubio-Muñoz, Cristina
  • Hernández-Ferrer, Javier
  • Martínez Fernández de Landa, María Teresa
  • Benito, Ana M.
  • Maser, Wolfgang K.
Resumen del trabajo presentado al HeteroNanoCarb: "Advances and Applications in Carbon Related Nanomaterials: From pure to doped structures including heteroatom layers", celebrado en Benasque (España) del 7 al 11 de diciembre de 2015., This work has been funded by the Spanish Ministry MINECO and the European Regional Development Fund under the project ENE2013-48816-C5-5-R, and the Government of Aragon and the European Social Fund (DGA-ESF-T66 Grupo Consolidado)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Contribución de congreso (ConferenceOutput)

Achievements and perspectives on carbon nanotube conducting inks

  • Ansón-Casaos, Alejandro
  • Sanahuja-Parejo, Olga
  • Santidrián, Ana
  • Martínez Fernández de Landa, María Teresa
  • Benito, Ana M.
  • Maser, Wolfgang K.
Resumen del trabajo presentado al ChemOnTubes, celebrado en Bruselas (Bélgica) del 3 al 7 de abril de 2016., This work has been funded by MINECO and European Regional Development Fund (ENE2013-48816-C5-5-R NANOSOL-MAT), CSIC (project 2015801011 Intramural), Government of Aragón and European Social Fund (DGA-ESF-T66 Grupo Consolidado) and European Commission (H2020-MSCA-ITN-2014-ETN 642742 Enabling Excellence)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Contribución de congreso (ConferenceOutput)

Influence of different variables on SWCNT sorting by gel chromatography

  • Santidrián, Ana
  • Ansón-Casaos, Alejandro
  • Martínez Fernández de Landa, María Teresa
  • Benito, Ana M.
  • Maser, Wolfgang K.
Resumen del póster presentado a la Carbon Nanoscience and Nanotechnology Conference (NanoteC), celebrada en Dublin (Irlanda) del 31 de agosto al 3 de septiembre de 2016., Typically, during the production of single-walled carbon nanotubes (SWCNTs), mixtures of various chirality species are synthesized. The electronic structure of SWCNTs, described by the chiral vector (n,m), determines their unique electrical and optical properties. Dueto these properties, SWCNTs have found potential applications in numerous fields. In many cases, the separation between semiconducting and metallic SWCNTs is needed for electronic applications. In the present work, we study process variables in the separation of SWCNTs by a gel chromatography method. Two types of SWCNTs were used: high-pressure carbon monoxide disproportionation (HiPco) SWCNTs and are discharge SWCNTs. Besides, in order to study the process selectivity dependence on the surface chemistry, the initial SWCNTs were functionalized. The experimental procedure of the chromatography column consisted of 3 steps: firstly, the SWCNTs were dispersed in a surfactant (sodium dodecyl sulfate (SDS) or pluronic F-68) in order to have a stable dispersion and avoid aggregation of SWCNTs. Different concentrations of the SWCNT initial dispersion were investigated (2, 1, 0.5, 0.25, 0.1 mglmq. Next, ultracentrifugation was performed to remove residual catalyst particles, amorphous carbon, and tube bundles. Once the SWCNTs are purified and individualized, Sephacryl gel was used to sort metallic and semiconducting SWCNTs. Different column lengths and retention times were investigated. Elution was done using a surfactant and the different fractions were collected sequentially. The collected fractions were characterized by Raman spectroscopy and absorption spectroscopy. The spectroscopy results show that the former fraction are enriched in SWCNTs in resonance via metallic transitions (E11M) and the latter fractions mainly contained SWCNTs in resonance via E22S. The results show that the technique effectively separates the SWCNTs. In addition, it was found that the selection process depends on the origin of the SWCNTs material and it is highly affected by the surface chemistry. Besides, the concentration of the raw SWCNTs dispersion and the length of the column play an important role towards the separation of single-chirality SWCNTs. The optimum conditions are reached by low SWCNT concentrations and long columns., This work has been funded by MINECO and European Regional Deve1opment Fund (ENE2013-48816-C5-5-R "NANOSOL-MAT"), CSIC (project 2015801011 "lntramural"), Government of Aragón and European Social Fund (DGA-ESF-T66 "Grupo Consolidado") and European Commission (H2020-MSCA-ITN-2014-ETN 642742 "Enabling Excellence")., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Contribución de congreso (ConferenceOutput)

Three problems in carbon nanotube and graphene fluid dynamics

  • Ansón-Casaos, Alejandro
  • Sanahuja-Parejo, Olga
  • Rubio-Muñoz, Cristina
  • Santidrián, Ana
  • Martínez Fernández de Landa, María Teresa
  • Benito, Ana M.
  • Maser, Wolfgang K.
Resumen del trabajo presentado al Nanomath, celebrado en Toulouse (Francia) del 27 al 30 de junio de 2016., This work has been funcled by MINECO ancl Europea.n Regional Development Funcl (ENE2013-48816-C5-5-R "NANOSOL-MAT"), CSIC (project 2015801011 "Int.ramural"), Government of Aragón and European Social Fund (DGA-ESF-T66 "Grupo Consolidado") ancl European Commission (H2020-MSCA-ITN-2014-ETN 642742 "Enabling Excellcnce")., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Contribución de congreso (ConferenceOutput)

Liquid phase Raman spectroscopy of carbon nanotubes sorted by gel chromatography

  • Santidrián, Ana
  • Ansón-Casaos, Alejandro
  • Martínez Fernández de Landa, María Teresa
  • Benito, Ana M.
  • Maser, Wolfgang K.
Resumen del póster presentado al ChemOnTubes, celebrado en Bruselas (Bélgica) del 3 al 7 de abril de 2016., Single-walled carbon nanotubes (SWCNTs) are considered as ene-dimensional (1 D) nanomaterials. The density of states (DOS) of 1 D materials is nota continuous function of energy, but it is confined in the so called van Hove singularities (vHSs). The electronic structure of SWCNTs, described by the chiral vector (n,m), determines their unique electrical and optical properties. Due to these properties, SWCNTs have found potential applications in numerous fields. In many cases, it would be desirable to have well-dispersed individualized SWCNTs. Besides, the separation between semiconducting and metallic SWCNTs is needed in electrical applications. In the present work, we study process variables in the separation of SWCNTs by a gel chromatography method. Firstly, the SWCNTs were dispersed in sodium dodecyl sulfate (SDS) in order to have a stable dispersion of SWCNTs and avoid aggregation of SWCNTs. Next, ultracentrifugation was effected to remove residual catalyst particles, amorphous carbon, and tube bundles. Once the SWCNTs are purified and individualized, Sephacryl gel was used to sort metallic and semiconducting SWCNTs. Elution was done using SDS, and the different fractions were collected in separated vials. In Figure 1, we observe the Raman spectra (Figure 1 a. and 1 b.) and absorption spectra (Figure 1 c.) of the separated fractions: raw SWCNTs (black line ), fraction 1 (red dashed line ), fraction 12 (green broken line), and fraction 17 (blue dotted line). The spectroscopy results show that the bands corresponding to SWCNTs in resonance via metallic transitions (E11 M) are more intense in the first fractions (Fr. 1) and bleached in the others (Fr. 12 and Fr. 17). The spectra of the following fractions (Fr. 12 and Fr. 17) present more intense bands in resonance via E22S. Therefore, the former fractions are enriched in metallic SWCNTs and the latter in semiconducting SWCNTs. The results show that the technique effectively separates the SWCNTs. In addition, it was found that the concentration of the raw SWCNTs dispersion plays an important role towards the separation of single-chirality SWCNTs., This work has been funded by MINECO and European Regional Development Fund (ENE2013-48816-C5-5-R "NANOSOL-MA T"), CSIC (project 2015801011 "lntramural"), Government of Aragón and European Social Fund (DGA-ESF-T66 "Grupo Consolidado") and European Commission (H2020-MSCA-ITN-2014-ETN 642742 "Enabling Excellence")., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Biocapture platform based on α-poly-l-lysine functionalized SWCNTs for lead monitoring

  • Reartes, Daiana F.
  • Ramírez, María Laura
  • González Domínguez, José Miguel
  • Martínez Fernández de Landa, María Teresa
  • Rivas, Gustavo A.
  • Gutiérrez, Fabiana A.
  • Rodríguez, Marcela C.
7 figures, 2 tables.-- © 2026. This manuscript version is made available under the CC-BY-NC-ND 4.0 license https://creativecommons.org/licenses/by-nc-nd/4.0/, This work reports the development of an efficient electrochemical sensing strategy for Pb(II) quantification based on glassy carbon electrodes (GCE) modified with single-walled carbon nanotubes (SWCNTs) covalently functionalized with α-poly-l-lysine (α-PLys). The resulting platform enables the selective preconcentration of Pb(II) at open-circuit potential (OCP) through affinity-driven complexation with the primary amino groups of the α-poly(l-lysine) residues immobilized on the SWCNT surface, which is further reduced in a fresh supporting electrolyte solution at −1.20 V, potential that is applied solely to convert the surface-confined Pb(II) into metallic Pb prior to stripping detection. The analytical signal was obtained from the oxidation of Pb by differential pulse voltammetry (DPV) in 0.020 M acetate buffer (pH 5.00). A linear response was obtained over the concentration range from 2.5 to 400.0 μg L−1, with a sensitivity of (0.065 ± 0.001) μA μg−1 L and a detection limit of 0.75 μg L−1. The sensor exhibited high selectivity in the presence of elevated concentrations of potentially interfering species. The applicability of the proposed platform was successfully demonstrated using Pb(II)-spiked surface water samples, showing excellent recoveries and strong agreement with inductively coupled plasma mass spectrometry (ICP-MS)., Authors acknowledge to CONICET, SECyT-UNC, ANPCyT (PICT 2018-01177, PICT 2019-04111), MINCyT-Córdoba, Spanish Ministry of Economy and Competitiveness (MINECO) project ENE2013-48816-C5-5-R, and the Government of Aragon and the European Social Fund under project grant DGA-FSE-T66 CNN for the financial support of the research activities. D.F.R. and M.L.R. acknowledge CONICET for the fellowship received., Peer reviewed
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Graphene oxide-carbon nanotube hybrid assemblies: Cooperatively strengthened OH¿O=C hydrogen bonds and the removal of chemisorbed water

  • Núñez, J.D.
  • Benito, A.M.
  • Rouzière, S.
  • Launois, P.
  • Arenal, R.
  • Ajayan, P.M.
  • Maser, W.K.
Owing to their great significance for energy storage and sensing applications, multi-layer papers consisting of graphene oxide-carbon nanotube (GO-CNT) hybrid sheets were prepared by in situ exfoliation of graphite oxide in the presence of oxidized CNTs (oCNTs). For the first time we elucidate the influence of oCNTs on chemisorbed water (CW), i.e. the water molecules inherently bound to the oxygen functional groups (OFGs) of graphene oxide (GO) and responsible for irreversible structural damage upon thermal reduction processes. We show that oCNTs self-assemble onto GO sheets during the liquid phase processing steps by forming cooperatively strengthened OH¿OC hydrogen bonds between the carboxylic groups of the oCNTs and OFGs of GO. At oCNT amounts of about 10 to 15 wt% this leads to the displacement of considerable amounts of CW without altering the original chemical composition of GO. The thermally reduced GO-CNT (rGO-CNT) papers reveal improved sp2 character and an enhancement of the specific capacitance by 75% with respect to thermally reduced GO (rGO), largely due to the effective removal of CW by oxidized CNTs. These findings disclose the relevance of the cooperative hydrogen bonding phenomena in graphene oxide paper/film electrodes for the development of improved electrochemical energy storage and sensing devices.