Skip to main content

-

IJCI-2014-19839

•
Funding agency name Ministerio de Ciencia e Innovación
Funding agency acronym MICINN
Program Programa Estatal de Promoción del Talento y su Empleabilidad en I+D+i
Subprogram Subprograma Estatal de Incorporación
Call Juan de la Cierva Incorporación
Call year 2014
State Plan 2013-2016 Plan Estatal de Investigación Científica y Técnica y de Innovación
Management unit Secretaría de Estado de Educación, Formación Profesional y Universidades
Beneficiary centre UNIVERSITAT POLITÈCNICA DE VALÈNCIA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 19
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Properties of LZS/nanoAl2O3 glass-ceramic composites

  • Arcaro, S.
  • Moreno, B.
  • Chinarro, E.
  • Nieto, M.I.
  • Moreno, R.
  • Novaes de Oliveira, A.P.
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
  • Borrell Tomás, María Amparo|||0000-0003-4292-4538
[EN] The LZS glass-ceramic (19.58 Li2O center dot 11.10ZrO(2)center dot 69.32SiO(2)) have a high coefficient thermal expansion (CTE) which can be a limitation in some applications. The addition of alumina in a LZS glass-ceramic matrix is able to reduce the CTE significantly. This happens because of the alumina affinity with respect to lithium silicates to form beta-spodumene (LiAlSi2O6), a crystalline phase having a CTE nearly zero (0.9 x 10(-6) degrees C-1).In this work, (1-5 vol%) Al2O3 nanoparticles (13 nm) were added to a LZS (3.5 mu m) glass-ceramic matrix to prepare composites with the main goal of evaluation the influence of Al2O3 on their mechanical, thermal and electrical properties. Each composition was wet homogenized and then dried at 110 degrees C for 48 h for disaggregation. The composites, sintered at 900 degrees C for 30 min, with relative densities between 92% and 98%, showed zircon and beta-spodumene as main crystalline phases. The incorporation of increasing additions of nanosized alumina progressively decreases the final density. This makes the properties to slightly decrease, also. The Young's modulus significantly decreases from 111 to 78 GPa of hardness due to the exponential variation with porosity, but the changes of toughness and hardness are much lower. The electrical conductivity was maintained within +/- 10-7 S. cm(-1), and the dielectric constant ranged from 5 to 6 for all compositions. Thermal conductivity ranged around 4.2 to 3.5 W/mK. (C) 2017 Elsevier B.V. All rights reserved., This work has been supported by CAPES in the frame of the International Cooperation Program Science without Borders for Special Visiting Researcher PVE (MEC/MCTI/CAPES/CNPq/FAPs/ No 71/2013), Project No A011/2013 (Brazil) and CNPq (National Council for Scientific and Technological Development, Brazil). This work has been also supported by Ministerio de Economia y Cornpetitividad and FEDER Funds under grant No MAT2016-67586-C3-R and grant ENE2013-49111-C2-1-R. A. Borrell acknowledges the MINECO for her Juan de la Cierva-Incorporacion contract (IJCI-2014-19839).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Comportamiento a fatiga térmica de la capa de anclaje de nuevas barreras térmicas cerámicas obtenidas mediante proyección por plasma atmosférico, Thermal fatigue behavior of new ceramic thermal barrier coatings obtained by the atmospheric plasma spray process

  • Carpio-Cobo, Pablo
  • Sánchez Vilches, Enrique
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
  • Borrell Tomás, María Amparo|||0000-0003-4292-4538
[PT] O desenvolvimento de novos materiais cerâmicos para aplicá-los em recobrimentos protetores frente à temperatura, também conhecidos como barreiras térmicas (Thermal Barrier Coatings o TBC), é de grande interesse para muitos setores, entre os que destacam as indústrias de geração de energia, aeronáutica e automobilística. Neste trabalho se realizou um estudo do comportamento à fadiga térmica, centrado na resposta de um dos componentes que constituem uma TBC: a camada de fixação. Os distintos componentes da TBC foram depositados mediante a técnica de projeção térmica por plasma atmosférico (Atmospheric Plasma Spraying ou APS). Estudouse a microestrutura e a composição da camada de fixação ao longo dos ciclos térmicos de estudo., [EN] The development of new ceramic materials to protect the metallic components against corrosion and oxidation at high temperature, also known as thermal barriers coating (TBC), is of a great interest topic for many industrial and consumer sectors, such as energy generation, aeronautics and automotive industries. This paper carried out a study on the thermal fatigue behavior of the bond coat, by centering the answer in one of the components which constitute a TBC: the anchor coat. The different TBC components were deposited by an Atmospheric Plasma Spraying (APS) Technique. Microstructure and anchor coat composition along the thermal cycles were studied., Este trabajo fue financiado por el Ministerio Español de Economía y Competitividad (MINECO), con fondos FEDER, a través de los proyectos MAT2012- 38364-C03 y MAT2015-67586-C3-R. La Dra. Amparo Borrell agradece al MINECO su contrato de Juan de la Cierva, IJCI-2014-19839, y Pablo Carpio agradece su contrato predoctoral del Plan de Promoción de la Universitat Jaume I, acción 3.1 (Ref. PREDOC/2009/10).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Alumina-zirconia coatings obtained by suspension plasma spraying from highly concentrated aqueous suspensions

  • Carpio-Cobo, Pablo
  • Sanchez Vilches, Enrique
  • Moreno, Rodrigo
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
  • Borrell Tomás, María Amparo|||0000-0003-4292-4538
[EN] Suspension plasma spraying (SPS) deposition represents an innovative technique to produce coatings that exhib- it improved properties. However, the key to obtain coatings with superior functional properties relies on the in- vestigation of the suspensions as starting materials. For this reason, the present work deals with the suspension preparation for SPS process and its influence on the resulting coatings. Laboratory-prepared 60/40 wt% alumina-zirconia suspensions were concentrated to avoid energy loss and were then successfully deposited by SPS technique. The liquid used was water instead of ethanol due to economical, environmental and safety reasons. The preparation of the suspension plays an important role in SPS process since stable and well-dispersed water suspensions are difficult to obtain. For this reason, colloidal behaviour characterisation of the starting particles as well as rheological optimisation of the feedstock suspensions was ad- dressed in this research. Suspensions with different solid loadings (up to 30 vol.% or 72 wt%) were deposited using several spraying dis- tances. All coatings displayed a bimodal microstructure consisting in partially melted zones surrounded by a fully melted matrix. α-Al2O3 and t′-ZrO2 constituted the main crystalline phases, but differences in the microstructure and properties of the coatings were observed. From these results, some relations between starting suspension and spraying parameters with coating characteristics were found. Thus the optimal spraying distance becomes shorter when the suspension solid loading increases., This work has been supported by the Spanish Ministry of Economy and Competitiveness, MINECO (project MAT2015-67586-C3-R). M.D. Salvador thanks CAPES – Programa Ciências sem Fronteiras (Brazil) for the concession of a PVE project N° A086/2013. A. Borrell acknowledges the MINECO for her Juan de la Cierva-Incorporación contract (IJCI-2014- 19839) and the Program to Support Research and Development (PAID00-15) of the Universitat Politècnica de València.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Fretting fatigue wear behavior of Y-TZP dental ceramics processed by non-conventional microwave sintering

  • PRESENDA-BARRERA, ALVARO
  • Vleugels, Jozef
  • Moreno, Rodrigo
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
  • Borrell Tomás, María Amparo|||0000-0003-4292-4538
[EN] The fretting wear behavior of self-mated Y-TZP dental materials obtained by non-conventional microwave and conventional sintering has been investigated. Two 3Y-TZP materials, a widely utilized commercial dental ceramic (LAVA) and a lab-prepared 3Y-TZP powder based equivalent have been assessed. Relative density and mechanical properties as well as the grain size variations upon sintering have been evaluated. After exposure to selected gross slip regime fretting wear conditions, the wear tracks have been characterized allowing the measurement of the coefficient of friction, track profiles, and pit features. The results indicate thaT microwave sintering results in a similar fretting wear behavior as observed for conventional sintered 3YTZP, since the measured volumetric wear loss is of a comparable order of magnitude. Regarding the influence of the grain size, the analysis revealed that a large grain size (>300 nm) results in an increased wear volume and that a higher resistance to fretting wear is constrained to a midrange particle size. Since the fracture toughness of all investigated ceramic grades was comparable, the influence of the fracture toughness could not be assessed. Abrasive grooving, delamination and microcracking have been identified as major wear mechanisms inside the wear tracks for both conventional and microwave sintered 3Y-TZP. In general, microwave sintering can provide 3Y-TZP dental materials with a comparable fretting wear resistance as that observed for conventional sintering using lower dwell sintering temperatures and a shorter processing time., Spanish Ministry of Economy and Competitiveness MINECO, Grant/Award Number: MAT2015-67586-C3-R; Generalitat Valenciana, Grant/Award Number: GRI-SOLIA/2013/035, GV/2014/009; MINECO, Grant/Award Number: IJCI-2014-19839.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Impact of Feedstock Nature on Thermal Conductivity of YSZ Thermal Barrier Coatings Obtained by Plasma Spraying

  • Carpio-Cobo, Pablo
  • Miranda, M.
  • Sánchez, E.
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
  • Benavente Martínez, Rut|||0000-0002-4566-9475
  • Borrell Tomás, María Amparo|||0000-0003-4292-4538
[EN] Yttria-stabilized zirconia (YSZ) coatings with low thermal conductivity were obtained using three different particle size distributions as starting powder: nano-, submicron- and bimodal submicron/nano-sized particles. On the one hand, these particles were reconstituted into micrometric, spray-dry agglomerates, which were subsequently deposited by means of conventional atmospheric plasma spraying (APS). On the other hand, the starting particles were dispersed in water and the resultant suspensions were deposited by means of suspension plasma spraying (SPS). The coatings were thermally treated to assess their sintering resistance. As-sprayed and thermally treated coatings were then characterized in terms of microstructure (FEG-SEM) and thermal diffusivity (laser flash equipment). The results showed that SPS coatings exhibited extremely low thermal conductivity at low temperature which drastically augmented with increasing temperature. On the other hand, APS coatings also exhibited low thermal conductivities but their values were higher than those of the SPS coatings at the lowest temperature tested while the conductivities hardly varied with temperature., This work has been supported by the Spanish Ministry of Economy and Competitiveness (project MAT2015-67586-C3-R) and Research Promotion Plan of the Universitat Jaume I, action 2.1 (ref. E-2011 - 05) and action 3.1 (ref. PREDOC/2009/10). A. Borrell acknowledges the Spanish Ministry of Economy and Competitiveness for her Juan de la Cierva-Incorporacion contract (IJCI-2014-19839). M. Miranda would like to thank the European Commission (FP7-Marie Curie Intra-European Fellowship, BIOHYMAT).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Colloidal processing of fully stabilized zirconia laminates comprising graphene oxide-enriched layers

  • Rincón, Acacio
  • Moreno, Rodrigo
  • Gutierrez González, Fidel Carlos
  • Sainz, Raquel
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
  • Borrell Tomás, María Amparo|||0000-0003-4292-4538
Multilayer materials have demonstrated to provide an efficient mechanism for toughening by deflection of a propagating crack by weak interlayers. Therefore, the aim of this work is to study the colloidal processing of 8 mol% yttria stabilized zirconia (8YSZ) based laminates by intercalating thin layers of graphene enriched with 8YSZ, and to evaluate the advantages of such multilayered structure in the propagation of cracks induced by indentation. Green tapes of 8YSZ and graphene-oxide with YSZ were obtained by aqueous tape casting and sintered in one-step by spark plasma sintering at 1400 degrees C. Microindentation results showed that the indentation cracks propagate within the horizontal direction within the ceramic layer, but in the cross-sectional direction the presence of the GO-rich layers stops the cracks without deflection or bifurcation. The hardness and elastic modulus values were higher than 17.6 GPa and 230 GPa, respectively, and similar for all layers., This work has been supported by the Spanish Ministry of Economy and Competitiveness (project MAT2015-67586-C3-R) and the Generalitat Valenciana by the financial support for the GV/2014/009 project. M.D. Salvador thanks to CAPES-Programa Ciencias sem Fronteiras (Brazil) for the concession of a PVE project No. A086/2013. A. Borrell, acknowledges the Spanish Ministry of Economy and Competitiveness for her Juan de la Cierva-Incorporacion contract (IJCI-2014-19839).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Sliding wear behavior of Al2O3-NbC composites obtained by conventional and nonconventional techniques

  • Ribeiro-Rodrigues Alecrim, Laís
  • Ferreira, J.A.
  • Gutierrez-Gonzalez, C.F.
  • Pallone, E.M.J.A.
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
  • Borrell Tomás, María Amparo|||0000-0003-4292-4538
[EN] This study aims to investigate the dry sliding wear behavior of Al2O3 5vol.%NbC nanocomposite sintered by conventional and spark plasma sintering at temperatures from 1450 to 1600 ºC. The tests were performed using WC 6 wt%Co balls as a counterpart material, a load of 30 and 60 N, a sliding distance of 2000 m and a sliding speed of 0.1 m/s. The consolidation techniques influenced the friction coefficient, wear rates and patterns. Samples tested at 30 N showed better wear resistance than the samples tests with 60 N. The nanocomposites obtained by SPS at 1500 ºC exhibited a lower friction coefficient and wear rate compared to all other materials. The results indicated that Al2O3-NbC nanocomposites show promise as material for cutting tool applications., This work has been financial support by the Brazilian institution CAPES for the project CAPES-PVE A086/2013 (project No 23038.009604/2013-12). A. Borrell acknowledges the Spanish Ministry of Economy and Competitiveness for her Juan de la Cierva-Incorporacion contract (IJCI-2014-19839).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Effect of Al2O3-NbC nanopowder incorporation on the mechanical properties of 3Y-TZP/Al2O3-NbC nanocomposites obtained by conventional and spark plasma sintering

  • Salem, Raphael
  • Monteiro, Raphael
  • Gutierrez, Carlos F.
  • Chinelatto, Adriana S.A.
  • Chinelatto, Adilson
  • Ferreira, Julieta
  • Pallone, Eliria
  • Borrell Tomás, María Amparo|||0000-0003-4292-4538
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
[EN] The incorporation of Al2O3-NbC-nanopowder reinforcement in a 3Y-TZP matrix, and its influence on the mechanical properties of 3YTZP/Al2O3-NbC nanocomposites, obtained by conventional and spark plasma sintering (SPS), was investigated. Nanometric powders of Al2O3-NbC were prepared by reactive high-energy milling, deagglomeration, and leaching with acid, and added to the 3Y-TZP matrix, at a proportion of 5 vol%. The final powders were dried under airflow, compacted, and sintered in the temperature range of 1300-1500 degrees C. The effects of the sintering technique and final temperature, on the microstructure and mechanical properties, such as hardness, toughness, and Young's modulus, were analysed. Fracture toughness of the material reinforced with Al2O3-NbC nanopowders, which is one of its most important properties, differed significantly from that of the 3Y-TZP monolith (5.2 MPa m(1/2)). The nanocomposites, sintered conventionally at 1450 degrees C, showed higher fracture toughness (8.7 MPa m(1/2)). Microstructure observations indicated that NbC nanoparticles were dispersed homogeneously within the 3Y-TZP matrix, and limited its grain growth. However, partial oxidation of the NbC on the nanocomposite surface, at the conventional sintering temperature of 1500 degrees C, caused a reduction in the fracture toughness., The authors acknowledge the Brazilian institutions CAPES-PVE (grant number 23038.009604/2013-12), FAPESP (grant number 2015/07319-8), Fundação Araucária (grant number 810/2014), European Union/Erasmus Mundus for doctorate mobility (grant number EB15DM1542), and the Spanish Ministry of Economy and Competitiveness (grant number IJCI-2014-19839).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Wear behavior of conventional and spark plasma sintered Al2O3-NbC nanocomposites

  • Alecrim, Laís
  • Ferreira, Julieta
  • Pallone, Eliria
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
  • Borrell Tomás, María Amparo|||0000-0003-4292-4538
[EN] This study aims to investigate the dry sliding wear behavior of Al2O3-5vol.% NbC nanocomposites sintered by two different consolidation techniques: conventional sintering (CS) and spark plasma sintering (SPS) at temperatures ranging from 1450 to 1600 degrees C. The dry sliding wear tests were performed on a tribometer with a ball-on-disc configuration using an Al2O3 ball as a counterpart material, with a normal contact load of 15 and 30 N, a sliding distance of 2000m and a sliding speed of 0.1m/s at room temperature and ambient environment. The sintering methods, mechanical properties and applied load acted directly on the wear mechanism of the nanocomposites. The samples sintered by SPS exhibited higher densification and hardness, in addition to a lower friction coefficient and wear rate. Based on the wear rate, these nanocomposites exhibited a moderate regime with 15N of load, and several regimes when 30 N of applied load was used. The main wear mechanisms observed were plastic deformation, abrasion and grain pull-out. The excellent results show that Al2O3-NbC nanocomposites are ideal for the manufacture of new products such as cutting tools., Brazilian institution CAPES for the project CAPES-PVE A086/2013, Grant/Award Number: 23038.009604/2013-12
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Effects of microwave sintering in aging resistance of zirconia-based ceramics

  • PRESENDA-BARRERA, ALVARO
  • Pallone, Eliria
  • Ferreira, Julieta
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
  • Penaranda-Foix, Felipe L.|||0000-0003-4012-0763
  • Catalá Civera, José Manuel|||0000-0002-0617-1762
  • Borrell Tomás, María Amparo|||0000-0003-4292-4538
[EN] Innovative techniques for materials processing that result in shorter times and lower energy consumption than conventional methods, such as microwave sintering, are currently under investigation in order to obtain fully-consolidated ceramic materials. Microwave sintering has important effects on the resulting properties of zirconia-based ceramics, which, in turn, affectits performance and durability, as in the case of their susceptibility to low temperature hydrothermal degradation (LTD), an ageing phenomenon that deteriorates their mechanical performance. The purpose of this work consists on assessing the effects of microwave sintering on the microstructure and mechanical performance of zirconia composites by comparing itto conventional sintering. Resistance to LTD of 3Y-TZP-only materials has also been evaluated. The results obtained in this work suggest that microwave sintering can reduce processing times and sintering temperatures when compared to conventional sintering while still obtaining dense zirconia-based ceramics and complying with the expected mechanical properties. At the same time, an increase in the resistance to LTD is also observed., This work has been supported by the Spanish Ministry of Economy and Competitiveness MINECO (project MAT2015-67586-C3-R). The authors acknowledge to CAPES Programa Ciencias sem Fronteiras (Brazil) for the concession of a PVE project No. A086/2013. A. Presenda acknowledges the Generalitat Valenciana for his Santiago Grisolia scholarship (GRISOLIA/2013/035). A. Borrell acknowledges the MINECO for her Juan de la Cierva-Incorporacion contract (IJCI-2014-19839).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Effect of reinforcement NbC phase on the mechanical properties of Al2O3-NbC nanocomposites obtained by spark plasma sintering

  • Ribeiro-Rodrigues Alecrim, Laís
  • Ferreira, J.A.
  • Gutiérrez-González, C.
  • Pallone, Eliria
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
  • Borrell Tomás, María Amparo|||0000-0003-4292-4538
[EN] The sintering behavior of Al2O3-NbC nanocomposites fabricated via conventional and spark plasma sintering (SPS) was investigated. The nanometric powders of NbC were prepared by reactive high-energy milling, deagglomerated, leached with acid, added to the Al2O3 matrix in the proportion of 5vol% and dried under airflow. Then, the nanocomposite powders were densified at different temperatures, 1450-1600C. Effect of sintering temperature on the microstructure and mechanical properties such as hardness, toughness and bending strength were analyzed. The Al2O3-NbC nanocomposites obtained by SPS show full density and maximum hardness value>25GPa and bending strength of 532MPa at 1500C. Microstructure observations indicate that NbC nanoparticles are dispersed homogeneously within Al2O3 matrix and limit their grain growth. Scanning electron microscopy examination of the fracture surfaces of dense samples obtained at 1600C by SPS revealed partial melting of the particle surfaces due to the discharge effec, This work has been financial support by the Brazilian institution CAPES for the project CAPES-PVE A086/2013 (project no. 23038.009604/2013-12). A Borrell, acknowledges the Spanish Ministry of Economy and Competitiveness for her Juan de la Cierva-Incorporacion contract (IJCI-2014-19839).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Thermal behaviour of multilayer and functionally-graded YSZ/Gd2Zr2O7 coatings

  • Carpio-Cobo, Pablo
  • Sanchez, E.
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
  • Borrell Tomás, María Amparo|||0000-0003-4292-4538
[EN] Zirconates with pyrochlore structure, such as Gd2Zr2O7, are new promising thermal barrier coatings because of their very low thermal conductivity and good chemical resistance against molten salts. However, their coefficient of thermal expansion is low, therefore their thermal fatigue resistance is compromised. As a solution, the combination of yttria-stabilised zirconia (YSZ) and Gd2Zr2O7 can reduce the thermal contraction mismatch between the thermal barrier coating parts. In the present study, two possible designs have been performed to combine YSZ/Gd2Zr2O7. On the one hand, a multilayer coating was obtained where YSZ layer was deposited between a Gd2Zr2O7 layer and a bond coat. On the other hand, a functionally-graded coating was designed where different layers with variable ratios of YSZ/Gd2Zr2O7 were deposited such that the composition gradually changed along the coating thickness. Multilayer and functionally-graded coatings underwent isothermal and thermally-cycled treatments in order to evaluate the oxidation, sintering effects and thermal fatigue resistance of the coatings. The YSZ/Gd2Zr2O7 multilayer coating displayed better thermal behaviour than the Gd2Zr2O7 monolayer coating but quite less thermal fatigue resistance compared to the conventional YSZ coating. However, the functionally-graded coating displays a good thermal fatigue resistance. Hence, it can be concluded that this kind of design is ideal to optimise the behaviour of thermal barrier coatings., This work has been supported by the Spanish Ministry of Economy and Competitiveness (project MAT2015-67586-C3-R). A. Borrell acknowledges the Spanish Ministry of Economy and Competitiveness for her Juan de la Cierva-Incorporacion contract (IJCI-2014-49839) and the Program to Support Research and Development (PAID-00-15) of the Universitat Politecnica de Valencia. P. Carpio acknowledges the Valencia Government for his post-doc contract (APOSTD/2016/040).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Microwave-assisted solution synthesis, microwave sintering and magnetic properties of cobalt ferrite

  • Fariñas, Juan Carlos
  • Moreno, Rodrigo
  • Pérez, A.
  • García, M. A.
  • García-Hernández, M.
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
  • Borrell Tomás, María Amparo|||0000-0003-4292-4538
[EN] A simple, soft, and fast microwave-assisted hydrothermal method was used for the preparation of nanocrystalline cobalt ferrite powders from commercially-available Fe(NO3)(3)center dot 9H(2)O, Co(NO3)(2)center dot 6H(2)O, ammonium hydroxide, and tetrapropylammonium hydroxide (TPAH). The synthesis was conducted in a sealed-vessel microwave reactor specifically designed for synthetic applications, and the resulting products were characterized by XRD, FE-SEM, TEM, and HR-TEM. After a systematic study of the influence of the microwave variables (temperature, reaction time and nature of the bases), highly crystalline CoFe2O4 nanoparticles with a high uniformity in morphology and size, were directly obtained by heating at 130 degrees C for 20 min using the base TPAH. Dense ceramics of cobalt ferrite were prepared by non-conventional, microwave sintering of synthesized nanopowders at temperatures of 850-900 degrees C. The magnetic properties of both the nanopowders and the sintered specimens were determined in order to establish their feasibility as a permanent magnet., This work has been carried out with financial support from the Spanish Ministry of Economy, Industry and Competitiveness (MINECO) and CSIC through the Projects MAT2015-67586-C3-R and NANOMIND, respectively. A. Borrell acknowledges MINECO for a Juan de la Cierva contract (IJCI-2014-19839).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

LZS/Al2O3 nanostructured composites obtained by colloidal processing and spark plasma sintering

  • Arcaro, S.
  • Novaes de Oliveira, A.P.
  • Gutierrez-Gonzalez, C.F.
  • Moreno, Rodrigo
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
  • Borrell Tomás, María Amparo|||0000-0003-4292-4538
[EN] Li2O-SiO2-ZrO2 (LZS) glass-ceramics have high mechanical strength, hardness, resistance to abrasion and chemical attack, but also a high coefficient of thermal expansion (CTE), which can be reduced adding alumina nanoparticles. The conventional glass-ceramic production is relatively complex and energy consuming, since it requires the melting of the raw materials to form a glass frit and a two-step milling process to obtain particle sizes adequate for compaction. This study describes the preparation of LZS glass-ceramics through a colloidal processing approach from mixtures of SiO2 and ZrO2 nanopowders and a Li precursor (lithium acetate obtained by reaction of the carbonate with acetic acid). Concentrated suspensions were freeze-dried to obtain homogeneous mixtures of powders that were pressed (100 MPa) and sintered conventionally and by spark plasma sintering. The effect of the alumina nanoparticles additions on suspensions rheology, sintering behavior and properties such as thermal expansion, thermal conductivity, hardness and Young's modulus were evaluated. (C) 2017 Elsevier Ltd. All rights reserved., This work has been supported by Ministerio de Economia y Competitividad (MINECO) and FEDER Funds under grant No MAT2016-67586-C3-R. Authors greatly acknowledge the financial Support of CAPES in the frame of the International Cooperation Program Science without Borders for Special Visiting Researcher PVE (MEC/MCTI/CAPES/CNPQ/FAPs/No 71/2013), Project no. A011/2013. A. Borrell acknowledges the MINECO for her Juan de la Cierva-Incorporacion contract (IJCI-2014-19839).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Colloidal processing of fully stabilized zirconia laminates comprising graphene oxide-enriched layers

  • Rincón, Acacio
  • Moreno, Rodrigo
  • Gutiérrez-González, C. F.
  • Sainz, Raquel
  • Salvador, M. D.
  • Borrell, Amparo
Multilayer materials have demonstrated to provide an efficient mechanism for toughening by deflection of a propagating crack by weak interlayers. Therefore, the aim of this work is to study the colloidal processing of 8 mol% yttria stabilized zirconia (8YSZ) based laminates by intercalating thin layers of graphene enriched with 8YSZ, and to evaluate the advantages of such multilayered structure in the propagation of cracks induced by indentation. Green tapes of 8YSZ and graphene-oxide with YSZ were obtained by aqueous tape casting and sintered in one-step by spark plasma sintering at 1400 °C. Microindentation results showed that the indentation cracks propagate within the horizontal direction within the ceramic layer, but in the cross-sectional direction the presence of the GO-rich layers stops the cracks without deflection or bifurcation. The hardness and elastic modulus values were higher than 17.6 GPa and 230 GPa, respectively, and similar for all layers., This work has been supported by the Spanish Ministry of Economy and Competitiveness (project MAT2015-67586-C3-R) and the Generalitat Valenciana by the financial support for the GV/2014/009 project. M.D. Salvador thanks to CAPES—Programa Ciências sem Fronteiras (Brazil) for the concession of a PVE project No. A086/2013. A. Borrell, acknowledges the Spanish Ministry of Economy and Competitiveness for her Juan de la Cierva-Incorporación contract (IJCI-2014-19839)., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Sliding wear behavior of Al2O3-NbC composites obtained by conventional and nonconventional techniques

  • Alecrim, L.R.R.
  • Ferreira, J. A.
  • Gutiérrez-González, C. F.
  • Salvador, M. D.
  • Borrell, Amparo
  • Pallone, E.M.J.A.
This study aims to investigate the dry sliding wear behavior of AlO–5vol%NbC nanocomposite sintered by conventional and spark plasma sintering at temperatures from 1450 to 1600 °C. The tests were performed using WC–6 wt%Co balls as a counterpart material, a load of 30 and 60 N, a sliding distance of 2000 m and a sliding speed of 0.1 m/s. The consolidation techniques influenced the friction coefficient, wear rates and patterns. Samples tested at 30 N showed better wear resistance than the samples tests with 60 N. The nanocomposites obtained by SPS at 1500 °C exhibited a lower friction coefficient and wear rate compared to all other materials. The results indicated that AlO-NbC nanocomposites show promise as material for cutting tool applications., This work has been financial support by the Brazilian institution CAPES for the project CAPES-PVE A086/2013 (project No 23038.009604/2013-12). A. Borrell acknowledges the Spanish Ministry of Economy and Competitiveness for her Juan de la Cierva-Incorporación contract (IJCI-2014–19839)., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Effect of reinforcement NbC phase on the mechanical properties of Al2O3-NbC nanocomposites obtained by spark plasma sintering

  • Alecrim, L.R.R.
  • Ferreira, J. A.
  • Gutiérrez-González, C. F.
  • Salvador, M. D.
  • Borrell, Amparo
  • Pallone, E.M.J.A.
The sintering behavior of AlO-NbC nanocomposites fabricated via conventional and spark plasma sintering (SPS) was investigated. The nanometric powders of NbC were prepared by reactive high-energy milling, deagglomerated, leached with acid, added to the AlO matrix in the proportion of 5 vol% and dried under airflow. Then, the nanocomposite powders were densified at different temperatures, 1450–1600 °C. Effect of sintering temperature on the microstructure and mechanical properties such as hardness, toughness and bending strength were analyzed. The AlO-NbC nanocomposites obtained by SPS show full density and maximum hardness value > 25 GPa and bending strength of 532 MPa at 1500 °C. Microstructure observations indicate that NbC nanoparticles are dispersed homogeneously within AlO matrix and limit their grain growth. Scanning electron microscopy examination of the fracture surfaces of dense samples obtained at 1600 °C by SPS revealed partial melting of the particle surfaces due to the discharge effect., This work has been financial support by the Brazilian institution CAPES for the project CAPES-PVE A086/2013 (project no. 23038.009604/2013-12). A. Borrell, acknowledges the Spanish Ministry of Economy and Competitiveness for her Juan de la Cierva-Incorporación contract (IJCI-2014-19839)., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Effect of Al2O3-NbC nanopowder incorporation on the mechanical properties of 3Y-TZP/Al2O3-NbC nanocomposites obtained by conventional and spark plasma sintering

  • Salem, R.E.P.
  • Monteiro, F. R.
  • Gutiérrez-González, C. F.
  • Borrell, Amparo
  • Salvador, M. D.
  • Chinelatto, Adriana S. A.
  • Chinelatto, A. L.
  • Ferreira, J. A.
  • Pallone, E.M.J.A.
The incorporation of AlO-NbC-nanopowder reinforcement in a 3Y-TZP matrix, and its influence on the mechanical properties of 3YTZP/AlO-NbC nanocomposites, obtained by conventional and spark plasma sintering (SPS), was investigated. Nanometric powders of AlO-NbC were prepared by reactive high-energy milling, deagglomeration, and leaching with acid, and added to the 3Y-TZP matrix, at a proportion of 5 vol%. The final powders were dried under airflow, compacted, and sintered in the temperature range of 1300–1500 °C. The effects of the sintering technique and final temperature, on the microstructure and mechanical properties, such as hardness, toughness, and Young's modulus, were analysed. Fracture toughness of the material reinforced with AlO-NbC nanopowders, which is one of its most important properties, differed significantly from that of the 3Y-TZP monolith (5.2 MPa m). The nanocomposites, sintered conventionally at 1450 °C, showed higher fracture toughness (8.7 MPa m). Microstructure observations indicated that NbC nanoparticles were dispersed homogeneously within the 3Y-TZP matrix, and limited its grain growth. However, partial oxidation of the NbC on the nanocomposite surface, at the conventional sintering temperature of 1500 °C, caused a reduction in the fracture toughness., The authors acknowledge the Brazilian institutions CAPES-PVE (grant number 23038.009604/2013-12), FAPESP (grant number 2015/07319-8), Fundação Araucária (grant number 810/2014), European Union/Erasmus Mundus for doctorate mobility (grant number EB15DM1542), and the Spanish Ministry of Economy and Competitiveness (grant number IJCI-2014-19839)., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

LZS/Al2O3 nanostructured composites obtained by colloidal processing and spark plasma sintering

  • Arcaro, Sabrina
  • Oliveira, A.P.N.
  • Gutiérrez-González, C. F.
  • Salvador, M. D.
  • Borrell, Amparo
  • Moreno, Rodrigo
Li2O-SiO2-ZrO2 (LZS) glass-ceramics have high mechanical strength, hardness, resistance to abrasion and chemical attack, but also a high coefficient of thermal expansion (CTE), which can be reduced adding alumina nanoparticles. The conventional glass-ceramic production is relatively complex and energy consuming, since it requires the melting of the raw materials to form a glass frit and a two-step milling process to obtain particle sizes adequate for compaction. This study describes the preparation of LZS glass-ceramics through a colloidal processing approach from mixtures of SiO2 and ZrO2 nanopowders and a Li precursor (lithium acetate obtained by reaction of the carbonate with acetic acid). Concentrated suspensions were freeze-dried to obtain homogeneous mixtures of powders that were pressed (100 MPa) and sintered conventionally and by spark plasma sintering. The effect of the alumina nanoparticles additions on suspensions rheology, sintering behavior and properties such as thermal expansion, thermal conductivity, hardness and Young’s modulus were evaluated., This work has been supported by Ministerio de Economía y Competitividad (MINECO) and FEDER Funds under grant N° MAT2016-67586-C3-R. Authors greatly acknowledge the financial Support of CAPES in the frame of the International Cooperation Program Science without Borders for Special Visiting Researcher PVE (MEC/MCTI/CAPES/CNPq/FAPs/N°71/2013), Project no. A011/2013. A. Borrell acknowledges the MINECO for her Juan de la Cierva-Incorporación contract (IJCI-2014-19839)., Peer reviewed