Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 11
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Exchange bias and two steps magnetization reversal in porous Co/CoO layer

  • Ovejero, Jesús G.
  • Godinho, Vanda
  • Lacroix, Bertrand
  • García García-Tuñón, Miguel Ángel
  • Hernando, Antonio
  • Fernández-Camacho, A.
In this paper Co/CoO thick layers (hundreds of nanometers) of different porosity and oxidation degree were prepared in a magnetron sputtering deposition process by tailoring the DC sputtering power, as well as the process gas and target composition. The control of the synthesis parameters allowed the nanostructuration of the films with a singular distribution of closed pores and a controlled amount of CoO. We observed an exchange bias field of 2.8 KOe for porous Co/CoO composites, similar to Co/CoO bilayers but for coatings thicker than 300 nm. Besides, it was observed that the coating presents bistable magnetic features when cooled under zero field conditions as a result of the unusual exchange coupling., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Ag-AgO nanostructures on glass substrates by solid-state dewetting: From extended to localized surface plasmons

  • Serrano Rubio, Aída
  • Llorca-Hernando, O.
  • Campo, Ángel Adolfo del
  • Rubio Marcos, Fernando
  • Rodríguez de la Fuente, Óscar
  • Fernández Lozano, José Francisco
  • García García-Tuñón, Miguel Ángel
[EN] We present here a study on the modification of morphological and plasmonic properties of Ag thin films deposited on glass substrates upon annealing in air at different temperatures. Initially, Ag films are continuous and exhibit extended surface plasmons with a resonant absorbance that depends on the film thickness. The dewetting process promotes the formation of nanoparticles with different sizes, shapes, and agglomerations states, besides a partial oxidation from Ag to AgO at surface level. The final Ag-AgO nanostructures are dependent on the annealing temperature and initial film thickness. The optical properties evolve from those typical of metallic films with high reflectivity and extended surface plasmon resonance toward localized surface plasmons characteristic of nanoparticles. The optical evolution and the final plasmonic response are evaluated according to the morphological and structural features of nanostructures., This work has been supported by the Ministerio Español de Economía, Industria y Competitividad (MINECO) through the projects MAT2017-86540-C4-1-R, MAT2013-48009-C4-1-P and FIS-2008-06249. Project supported by a 2016 BBVA Foundation Grant for Researchers and Cultural Creators. F. R-M. is also indebted to MINECO for a ‘Ramon y Cajal’ contract (Ref: RyC-2015-18626), which is co-financed by the European Social Fund.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Tailoring nanostructured surfaces with plasmonic/magnetic multifunctional response

  • Serrano Rubio, Aída
  • Rodríguez de la Fuente, Óscar
  • García-Hernández, Mar
  • Campo, G.
  • de Julián Fernández, C.
  • Fernández Lozano, José Francisco
  • García García-Tuñón, Miguel Ángel
[EN] In this work, we present an innovative way to functionalize large surfaces combining both plasmonic and magnetic nanoparticles on a substrate, by the growth of bilayers and a subsequent single annealing. In particular, we show here the formation of Au and γ-FeO nanoparticles using this route. Thermal treatments promote the nanostructuration of the film plus a partial oxidation of Fe to form ferrimagnetic oxides. For this purpose, annealing conditions and the structure of the bilayer must be selected to achieve an optimal nanostructuration, avoiding the full oxidation of Fe to form antiferromagnetic hematite., Project supported by a 2016 BBVA Foundation Grant for Researchers and Cultural Creators. This work has been also supported by the Ministerio Español de Economía y Competitividad (MINECO) through the projects MAT2017-86540-C4-1-R, MAT2014-52405-C02-02 and CSIC 20150E068. A. S. acknowledges the Comunidad de Madrid for the financial support (grant nº 2017-t2/IND-5395).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

New insights into the structural analysis of maghemite and (MFe2O4, M = Co, Zn) ferrite nanoparticles synthesized by a microwave-assisted polyol process

  • Gallo-Cordova, Álvaro
  • Espinosa, Ana
  • Serrano Rubio, Aída
  • Gutiérrez, Lucía
  • Menéndez, Nieves
  • Morales, María Del Puerto
  • Mazarío, Eva
[EN] The search for more efficient, scalable, reproducible and standardized synthesis methods able to control particle size and crystallinity is still a challenge in nanotechnology. The one-pot microwave-assisted polyol process has been optimized for the synthesis of well-defined ferrite nanoparticles. Highly uniform and crystalline γ-Fe2O3, CoFe2O4 and ZnFe2O4 nanoparticles, with diameters below 14 nm have been prepared by an easy and reproducible one-pot microwave-assisted heating procedure in a polyol medium. A pure single phase and cubic spinel structure were confirmed by powder X-ray diffraction and Raman spectroscopy. Depending on the metal precursors, nanoparticles display magnetic features from superparamagnetic behaviour (Fe- A nd Zn-ferrites) to ferrimagnetism (Co ferrite) at room temperature. The iron oxidation state of 3+ and its short-range order coordination were studied by XAS (X-ray absorption spectroscopy). External field Mössbauer spectra, recorded at low temperature, confirmed the ferrimagnetic order with a Fe3+ and M2+ partial cationic distribution within both the A and B sites in zinc and cobalt ferrite, respectively. According to these results, the ferrite stoichiometry was (Zn0.70Fe0.30)[Zn0.30Fe1.70]O4 and (Co0.28Fe0.72)[Co0.72Fe1.28]O4. This journal is, This research was funded by the Spanish Ministry of Economy and Competitiveness under grants MAT2017-88148-R, MAT2017-86540-C4-1-R, RTI2018-095303-A-C52, and PGC2018-095642-B-I00. E. M. acknowledges financial support from the Juan de la Cierva Formación (FJCI-2015-23702) and to Comunidad de Madrid – Jóvenes Doctores project (SI1-PJI-2019-00366). L. G. acknowledges financial support from the Ramón y Cajal program (RYC-2014-15512). The authors would like to acknowledge the use of the Advanced Microscopy Laboratory (INA-Universidad de Zaragoza). A. S. and A. E. acknowledge financial support from the Comunidad de Madrid for the ‘‘Atracción de Talento Investigador’’ contracts (No. 2017-T2/IND5395 and 2018-T1/IND10058). A. E. is also grateful to the 2018/NMT-4321 and SEV-2016-0686 projects. The European Synchrotron (ESRF),Ministerio Español de Ciencia, Innovación y Universidades (MCIU) and Consejo Superior de Investigaciones Cientificas (CSIC) are acknowledged for the provision of synchrotron radiation facilities. We also thank the BM25- SpLine staff for the technical support beyond their duties.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Cold sintering process of ZnO ceramics: Effect of the nanoparticle/microparticle ratio

  • Serrano Rubio, Aída
  • Caballero-Calero, Olga
  • García García-Tuñón, Miguel Ángel
  • Lazić, Snežana
  • Carmona, N.
  • Castro, Germán R.
  • Martín-González, Marisol
  • Fernández Lozano, José Francisco
We show the efficiency in the preparation of >95 % dense ZnO ceramics by cold sintering process through the incorporation of ZnO nanoparticles in the 1−10 wt% range at temperatures of 170 °C, pressures of 750 MPa and a pellet height/diameter ratio of 0.38. Morphological, structural and physical properties are dependent on the amount of ZnO nanoparticles incorporated into the system. After the densification by cold sintering process, ZnO ceramics show a reduction of the average valence indicating the deficiency of oxygen, similar to ceramics sintered by the conventional route. Besides, the generation of structural disorder and modifications into the ZnO lattice are identified in sintered ceramics, inducing intrinsic defects related to the loss of oxygen ions, the diffusion of zinc and zinc vacancies, which depend on the sintering process and the starting powders. These characteristics influence the final functional properties of the sintered ZnO ceramics, such as the visible photoluminescence signal., This work has been supported by the Ministerio Español de Ciencia, Innovación y Universidades (MCIU) through the projects MAT2017-86540-C4-1-R, MAT2017-86540-C4-3-R and RTI2018-095303-A-C52. The European Synchrotron (ESRF), MCIU and Consejo Superior de Investigaciones Cientificas (CSIC) are acknowledged for the provision of synchrotron radiation facilities. We also thank the BM25-SpLine staff for the technical support beyond their duties. A.S. acknowledges financial support from the Comunidad de Madrid for an “Atracción de Talento Investigador” contract (No. 2017-t2/IND5395).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Control of the Length of Fe73.5Si13.5Nb3Cu1B9 Microwires to Be Used for Magnetic and Microwave Absorbing Purposes

  • Gueye,Papa Gorgui Birame
  • López-Sánchez, Jesús
  • Navarro, Elena
  • Serrano Rubio, Aída
  • Marín, Pilar
A combination of high-energy ball milling, vacuum filtering, and sedimentation processes has been demonstrated to be a useful approach to reduce, in a controlled way, the length of as-cast Fe73.5Si13.5Nb3Cu1B9 amorphous magnetic microwires (MWs) and annealed material at 550 °C in nitrogen conditions. Homogeneous compositional microstructures with fairly narrow size distributions between 1300 and 11.7 μm are achieved, exhibiting tunable response as a soft magnetic material and as a microwave absorber. From the magnetic perspective, the soft magnetic character is increased with smaller length of the MWs, whereas the remanence has the opposite behavior mainly due to the structural defects and the loss of the shape anisotropy. From the microwave absorption perspective, a novel potential applicability is tested in these refined microstructures. This innovation consists of coatings based on commercial paints with a filling percentage of 0.55% of MWs with different lengths deposited on metallic sheets. Large attenuation values around −40 dB are obtained in narrow spectral windows located in the GHz range, and their position can be varied by combining different optimized lengths of MW. As an example of this powerful mechanism for absorbing microwaves at specific frequencies, MW lengths of 2 mm and 50 μm are chosen, where precise tailoring of the minimum reflection loss (RL) is obtained in a range between 8.85 and 13.25 GHz. To confirm these experimental results, an effective medium standard model proposed for electrical permittivity is used. Experimental and theoretical results are consistent and these novel composites are also proposed as a feasible candidate for designing frequency-selective microwave absorbers on demand, with low filling percentages and high absorption intensity values., The authors acknowledge the financial support from the Spanish Ministry of Science, Innovation and Universities under the projects RTI2018-095856-B-C21, MAT2017-86540-C4-1-R, and RTI2018-095303-A-C52 and from Comunidad de Madrid NANOFRONTMAG S2013/MIT-2850 and NANOMAGCOST S2018/NMT-4321. A.S. acknowledges the financial support from the Comunidad de Madrid for an “Atracción de Talento Investigador” contract (no. 2017-t2/IND5395)
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Heteropolyacids supported on boron nitride and carbon nitride for catalytic and catalytic photo-assisted alcohol dehydration

  • García-López, Elisa I.
  • Pomilla, Francesca R.
  • Krivtsov, Igor
  • Serrano, Aida
  • Liotta, Leonarda F.
  • Villar Rodil, Silvia
  • Paredes Nachón, Juan Ignacio
  • Marcì, Giuseppe
Keggin H3PW12O40 (PW12) and Wells-Dawson H6P2W18O60 (P2W18) heteropolyacids (HPAs) are photo(catalysts) for various acid-promoted and redox catalytic reactions. Their activity increases if they are deposited on certain supports as metal oxides or carbon materials. Although the surface area and acid-base interactions of the HPAs with supports are considered as key factors for the performance of the binary material, the role of the local structure changes in the HPAs upon their immobilization on solids must be also of primary importance, directly affecting both acidity and photoredox properties. Here, the (photo)catalytic performance of Keggin and Wells-Dawson heteropolytungstates supported on boron nitride (BN) and two types of carbon nitride (C3N4) in the gas-solid 2-propanol dehydration to propene has been studied. Apart from characterizing the materials by a set of conventional laboratory-scale structural and physical-chemical techniques, an insight into the variations of the local structure of supported HPAs is provided by means of X-ray absorption spectroscopy (XAS), and their influence on the supported HPAs (photo)catalytic activity is discussed. The irradiation with UV light increased the activity of both heteropolytungstates with respect to the catalytic experiments. The apparent activation energy calculated for the photo-assisted process resulted always lower with respect to that obtained for the catalytic one alone. Moreover, the materials that showed the highest apparent turnover frequency (TOF) were those in which the HPAs were impregnated on graphitic C3N4 or on BN and, in particular, the highest TOF values were observed at the highest temperature for the PW12/BN and P2W18/BN samples. Interestingly, the highest activity of HPAs supported on BN seems to be due to the stabilization of the W octahedral coordination, according to the XAS data., LFL is grateful to progetto di Ricerca ARS01_00637 Energie per l’Ambiente-TARANTO (PNR 2015-2020) for financial support. IK acknowledges support by Spanish MINECO (MAT2016-78155-C2-1-R), Gobierno del Principado de Asturias (GRUPIN-ID2018-170) and the Alexander von Humboldt Foundation through the Humboldt Research Fellowship. S.V.-R. and J.I.P. acknowledge financial support from the Spanish Ministerio de Ciencia, Innovación y Universidades (MCIU), the Spanish Agencia Estatal de Investigación and European Regional Development Fund (ERDF) through project RTI2018-100832B-I00, and partial funding by Plan de Ciencia, Tecnología e Innovación (PCTI) 2013-2017 del Principado de Asturias and the ERDF (project IDI/2018/000233). A.S acknowledges financial support from the MCIU through the projects MAT2017-86540-C4-1-R and RTI2018-095303-A-C52 and from the Comunidad de Madrid for an “Atracción de Talento Investigador” contract (No. 2017t2/IND5395). The European Synchrotron (ESRF), MCIU and Consejo Superior de Investigaciones Científicas (CSIC) are also acknowledged for the provision of synchrotron radiation facilities. We also thank the BM25-SpLine staff for the technical support beyond their duties., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Hexaferrite-based permanent magnets with upper magnetic properties by cold sintering process via a non-aqueous solvent

  • Serrano Rubio, Aída
  • García-Martín, Eduardo
  • Granados-Miralles, Cecilia
  • Gorni, Giulio
  • López-Sánchez, Jesús
  • Ruiz-Gómez, Sandra
  • Pérez, Lucas
  • Quesada, Adrián
  • Fernández Lozano, José Francisco
  • AMPHIBIAN Project ID:720853
[EN] The incessant technological pursuit towards a more sustainable and green future depends strongly on permanent magnets. At present, their use is widespread, making it imperative to develop new processing methods that generate highly competitive magnetic properties reducing the fabrication temperatures and costs. Herein, a novel strategy for developing dense sintered magnets based on Sr-hexaferrites with upper functional characteristics is presented. An innovative cold sintering approach using glacial acetic acid as novelty, followed by a post-annealing at 1100 °C, achieves a densification of the ceramic magnets of 92% with respect to the theoretical density and allows controlling the particle growth. After the cold sintering process, a fraction of amorphous SrO is identified, in addition to a partial transformation to α-FeO as secondary crystalline phase. 46 wt% of SrFeO remains, which is mostly recuperated after the post-thermal treatment. These findings do not significantly modify the final structure of ferrite magnets, neither at short- nor long-range order. The innovative process has a positive impact on the magnetic properties, yielding competitive ferrite magnets at lower sintering temperatures with an energy efficiency of at least 25%, which opens up a new horizon in the field of rare-earth free permanent magnets and new possibilities in other applications., This work has been supported by the Ministerio Español de Ciencia, Innovación y Universidades (MCIU) through the projects MAT2017-86540-C4-1-R and RTI2018-095303-A-C52 and The European Commission through the AMPHIBIAN Project (720853). Part of these experiments was performed at the CLÆSS beamline at ALBA Synchrotron with the collaboration of ALBA staff. A.S. acknowledges financial support from Comunidad de Madrid for an “Atracción de Talento Investigador” Contract (2017-t2/IND5395). C.G.-M. and A.Q. acknowledge financial support from Ministerio Español de Ciencia e Innovación (MICINN) through the “Juan de la Cierva” Program (FJC2018-035532-I) and the “Ramón y Cajal” Contract (RYC-2017-035532).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Effect of organic solvent on the cold sintering processing of SrFe12O19 platelet-based permanent magnets

  • Serrano Rubio, Aída
  • García-Martín, Eduardo
  • Granados-Miralles, Cecilia
  • López-Sánchez, Jesús
  • Gorni, Giulio
  • Quesada, Adrián
  • Fernández Lozano, José Francisco
  • AMPHIBIAN Project ID:720853
[EN] In this work we have investigated the effect of the solvent during the processing of SrFeO platelet-based permanent magnets by cold sintering process (CSP) plus a post-thermal treatment. Several organic solvents: glacial acetic acid, oleic acid and oleylamine have been analyzed, optimizing the CSP temperatures at 190−270 °C, under pressures of 375−670 MPa and 6−50 wt% of solvent. Modifications in the morphological and structural properties are identified depending on the solvent, which impacts on the magnetic response. Independently of the solvent, the mechanical integrity of ferrite magnets obtained by CSP is improved by a post-annealing at 1100 °C for 2 h, resulting in relative densities around 92 % with an average grain size of 1 μm and a fraction of SrFeO phase >91 %. H ≥ 2.1 kOe and M of 73 emu/g are obtained in the final sintered ceramic magnets, exhibiting the highest H value of 2.8 kOe for the magnet sintered using glacial acetic acid., This work has been supported by the Ministerio Español de Ciencia e Innovación (MICINN) through the projects MAT2017-86540-C4-1-R and RTI2018-095303-A-C52, and by the European Commission through Project H2020 No. 720853 (Amphibian). Part of these experiments was performed at the CLAESS beamline at ALBA Synchrotron with the collaboration of ALBA staff. A.S. acknowledges financial support from Comunidad de Madrid for an “Atracción de Talento Investigador” Contract (2017-t2/IND5395). C.G.-M. and A.Q. acknowledge financial support from MICINN through the “Juan de la Cierva” Program (FJC2018-035532-I) and the MICINN through the “Ramón y Cajal” Contract (RYC-2017-23320),, Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Dense strontium hexaferrite-based permanent magnet composites assisted by cold sintering process

  • García-Martín, Eduardo
  • Granados-Miralles, Cecilia
  • Ruiz-Gómez, Sandra
  • Pérez, Lucas
  • Campo, Ángel Adolfo del
  • Guzmán-Mínguez, J. C.
  • Julián Fernández, César de
  • Quesada, Adrián
  • Fernández Lozano, José Francisco
  • Serrano Rubio, Aída
  • AMPHIBIAN Project ID:720853
[EN] The use of rare-earth-based permanent magnets is one of the critical points for the development of the current technology. On the one hand, industry of the rare-earths is highly polluting due to the negative environmental impact of their extraction and, on the other hand, the sector is potentially dependent on China. Therefore, investigation is required both in the development of rare-earth-free permanent magnets and in sintering processes that enable their greener fabrication with attractive magnetic properties at a more competitive price. This work presents the use of a cold sintering process (CSP) followed by a post-annealing at 1100 °C as a new way to sinter composite permanent magnets based on strontium ferrite (SFO). Composites that incorporate a percentage ≤ 10% of an additional magnetic phase have been prepared and the morphological, structural and magnetic properties have been evaluated after each stage of the process. CSP induces a phase transformation of SFO in the composites, which is partially recovered by the post-thermal treatment improving the relative density to 92% and the magnetic response of the final magnets with a coercivity of up to 3.0 kOe. Control of the magnetic properties is possible through the composition and the grain size in the sintered magnets. These attractive results show the potential of the sintering approach as an alternative to develop modern rare-earth-free composite permanent magnets., This work has been supported by the Ministerio Español de Ciencia e Innovación (MICINN), Spain, through the projects MAT2017-86540-C4-1-R and RTI2018-095303-A-C52, and by the European Commission through Project H2020 No. 720853 (Amphibian). C.G.-M. and A.Q. acknowledge financial support from MICINN through the “Juan de la Cierva” program (FJC2018-035532-I) and the “Ramón y Cajal” contract (RYC-2017-23320). S. R.-G. gratefully acknowledges the financial support of the Alexander von Humboldt foundation, Germany. A.S. acknowledges the financialsupport from the Comunidad de Madrid, Spain, for an “Atracción de Talento Investigador” contract (No. 2017-t2/IND5395).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

CoSb3-based skutterudite nanocomposites prepared by cold sintering process with enhanced thermoelectric properties

  • Serrano Rubio, Aída
  • Caballero-Calero, Olga
  • Granados-Miralles, Cecilia
  • Gorni, Giulio
  • Manzano, Cristina V.
  • Rull Bravo, Marta
  • Moure Arroyo, Alberto
  • Martín-González, Marisol
  • Fernández Lozano, José Francisco
[EN] We show here for the first time the use of a cold sintering process (CSP) to sinter CoSb-based thermoelectric materials. CSP at 150 °C for 90 min under a uniaxial pressure of 750 MPa yields pieces with a relative density of 86 %, which is increased to around 92 % after a post-annealing at temperatures ≥ 500 °C in Ar atmosphere. The reported CSP produces Te doped-CoSb nanocomposites with similar morphological and structural characteristics to the starting nanopowders obtained by ball milling in air atmosphere. The post-thermal treatment induces grain coalescence and grain growth, crystallite size growth as well as compositional changes in the nanocomposite, decreasing the amount of the main phase, CoSb, and increasing the weight of secondary phase, CoSb, up to a 30 wt% at 600 °C. Remarkably, the average valence for the Co, Sb and Te absorbing atoms is neither transformed by the sintering process nor by the subsequent heat treatment. The functional response of the sintered thermoelectric nanocomposites exhibits a maximum figure of merit of 0.12(3) at room temperature for the nanocomposites sintered by CSP with a subsequent post-annealing at 500 °C. This is mainly due to its low thermal conductivity in comparison with similar powders sintered by other approaches, and it is explained by the morphological and structural properties. These findings represent an attractive alternative for obtaining efficient thermoelectric skutterudites by a scalable and cost-effective route., This work has been supported by the Ministerio Español de Ciencia e Innovación (MICINN) through the projects MAT2017-86540-C4-1-R, MAT2017-86540-C4-3-R, RTI2018-095303-A-C52, PID2020-114192RB-C41 and PID2020-118430GB-100. Part of these experiments were performed at the CLAESS-BL22 beamline at ALBA Synchrotron (Grant no. 2020094658) and in collaboration with ALBA staff. A.S. and C.V.M. acknowledge financial support from the Comunidad de Madrid for an “Atracción de Talento Investigador” Contract no. 2017-t2/IND5395 and 2019-t1/IND-13541, respectively. C.G.-M. acknowledges financial support from MICINN through the “Juan de la Cierva” program (FJC2018-035532-I). A.M. is indebted to MICINN for the “Ramón y Cajal” contract (RYC-2013-14436), which is co-financed with European Social Fund., Peer reviewed