Skip to main content

MATERIALES CON ALTAS PRESTACIONES PARA BATERIAS MAS SEGURAS, Y PILAS DE COMBUSTIBLES DE OXIDO SOLIDO SIMETRICAS MAS ECONOMICAS: DESARROLLO DE MATERIALES Y PROTOTIPOS

PID2019-106662RB-C43

•
Funding agency name Agencia Estatal de Investigación
Funding agency acronym AEI
Program Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Call Proyectos de I+D+i (Generación de Conocimiento y Retos Investigación)
Call year 2019
State Plan 2017-2020 Plan Estatal de Investigación Científica y Técnica y de Innovación
Beneficiary centre UNIVERSIDAD CARLOS III DE MADRID

Resultados relacionados

Resultados totales (Incluyendo duplicados): 7
Encontrada(s) 1 página(s)

e-Archivo. Repositorio Institucional de la Universidad Carlos III de Madrid
Publication Artículo científico (JournalArticle)

Reduction of Grain Boundary Resistance of La0.5Li0.5TiO3 by the Addition of Organic Polymers

  • Boyano, Iker
  • Mainar, Aroa R.
  • Blázquez, Alberto
  • Kvasha, Andriy
  • Bengoechea, Miguel
  • De Meatza, Iratxe
  • García Martín, Susana
  • Lumbier Álvarez, Alejandro
  • Sanz, Jesús
  • García Alvarado, Flaviano
The organic solvents that are widely used as electrolytes in lithium ion batteries present safety challenges due to their volatile and flammable nature. The replacement of liquid organic electrolytes by non-volatile and intrinsically safe ceramic solid electrolytes is an effective approach to address the safety issue. However, the high total resistance (bulk and grain boundary) of such compounds, especially at low temperatures, makes those solid electrolyte systems unpractical for many applications where high power and low temperature performance are required. The addition of small quantities of a polymer is an efficient and low cost approach to reduce the grain boundary resistance of inorganic solid electrolytes. Therefore, in this work, we study the ionic conductivity of different composites based on non-sintered lithium lanthanum titanium oxide (La0.5Li0.5TiO3) as inorganic ceramic material and organic polymers with different characteristics, added in low percentage (<15 wt.%). The proposed cheap composite solid electrolytes double the ionic conductivity of the less cost-effective sintered La0.5Li0.5TiO3., We thank the Spanish Ministry for Science and Technology (MAT2007-64486-C07-05) and CDTI (ALMAGRID of the "CERVERA Centros Tecnológicos" program, CER-20191006) for financial their support. JS, AV, SG, and FG also want to acknowledge Agencia Española de Investigación /Fondo Europeo de Desarrollo Regional (FEDER/UE) for funding the projects PID2019-106662RB-C41, C42, C43, and C44.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

New amphiphilic semi-interpenetrating networks based on polysulfone for anion-exchange membrane fuel cells with improved alkaline and mechanical stabilities

  • Ureña, N.
  • Pérez-Prior, M. T.
  • Río, Carmen del
  • Várez, A.
  • Levenfeld, Belén
As considerable advance has recently been made in enhancing the conductivity of anion-exchange membranes, durability has become the critical requirement in the development of fuel cells. Such properties often develop at the expense of the other. In this work, new amphiphilic semi-interpenetrating networks composed of free polysulfone and crosslinked polysulfone are synthesized for the first time. The same nature of both polymers makes them highly compatible. The free polymer provides the hydrophobic component, whereas the crosslinked polysulfone, functionalized with trimethylammonium, 1-methylimidazolium, or 1,2-dimethylimidazolium groups, is responsible for the ionic conductivity. The compatibility between both components in the blend, improves the mechanical properties, while unaffecting the transport properties. Thus, the obtained membranes exceed the mechanical behaviour of commercial materials, even in conditions of extreme humidity and temperature. The tensile strength of these synthesized membranes can reach to relatively high values, and when compared to the commercial PSU, the difference in tensile strength can be noted to be as low as 10%. Moreover, the tensile strength and the ductility values of the crosslinked PSU are higher than those obtained with non-crosslinked PSU. Furthermore, the membranes presented in this work show a great alkaline stability (e.g. semi-interpenetrating network containing 1,2-dimethylimidazolium maintains 87% of the ionic conductivity after 14 days of treatment). Thus, these membranes provide an improvement in the durability limiting factors, in comparison to functionalized polysulfones, fulfilling the requirements to be used as electrolytes in anion-exchange membrane fuel cells., We thank Agencia Estatal de Investigaci ́on (AEI)/Fondo Europeo de Desarrollo Regional (FEDER/UE) for funding the project MINECO (MAT2016-78632-C4-3-R, and PID-2019-106662RB-C43) which sup- ported this work. We also wish to thank the project from the Regional Government (Comunidad de Madrid through PEM4ENERGY-CM- UC3M)
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Sulfonated polysulfone/tio2(B) nanowires composite membranes as polymer electrolytes in fuel cells

  • Martínez-Morlanes, M. J.
  • De La Torre-Gamarra, C.
  • Pérez-Prior, M. T.
  • Lara-Benito, S.
  • Río, Carmen del
  • Várez, A.
  • Levenfeld, Belén
New proton conducting membranes based on sulfonated polysulfone (sPSU) reinforced with TiO(B) nanowires (1, 2, 5 and 10 wt.%) were synthesized and characterized. TiO(B) nanowires were synthesized by means of a hydrothermal method by mixing TiO precursor in aqueous solution of NaOH as solvent. The presence of the TiO(B) nanowires into the polymer were confirmed by means of Field Emission Scanning Electron Microscopy, Fourier transform infrared and X-ray diffraction. The thermal study showed an increase of almost 20 °C in the maximum temperature of sPSU backbone decomposition due to the presence of 10 wt.% TiO(B) nanowires. Water uptake also is improved with the presence of hydrophilic TiO(B) nanowires. Proton conductivity of sPSU with 10 wt.% TiO(B) nanowires was 21 mS cm (at 85 °C and 100% RH). Under these experimental conditions the power density was 350 mW cm similar to the value obtained for Nafion 117. Considering all these obtained results, the composite membrane doped with 10 wt.% TiO(B) nanowires is a promising candidate as proton exchange electrolyte in fuel cells (PEMFCs), especially those operating at high temperatures., The authors would like to thank the following Institution for funding the Projects: Agencia Española de Investigación /Fondo Europeo de Desarrollo Regional (FEDER/UE): Projects PID2019-106662RBC43 and MAT2016-78362-C4-3-R. Comunidad de Madrid: Projects “Excelencia para el Profesorado Universitario”—EPUC3M04) and PEM4ENERGY-CM-UC3
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Layer Shape LiFePO4 Obtained by Powder Extrusion Molding as Solid Boosters for Ferro/Ferricyanide Catholyte in Semisolid Redox Flow Battery: Effect of Porosity and Shape

  • Vivo-Vilches, José F.
  • Vázquez-Navalmoral, Álvaro
  • Torre-Gamarra, Carmen de la
  • Cebollada Borao, Jesús
  • Várez, Alejandro
  • Levenfeld, Belén
[EN] Powder extrusion molding is proposed to fabricate ceramic LiFePO layers (0.5–1.0 mm thickness) as solid booster for ferricyanide electrolyte in semisolid redox flow battery. In some extruded layers, the binder is partially decomposed, while in others it is completely removed and, afterwards, the material is sintered, so materials with different porosity and dimensions are obtained. After characterizing the materials, the kinetics for the reaction with ferricyanide is evaluated, being the binder-less materials the ones which react faster and reach larger degrees of oxidation. For the material with 1.0 mm thick comparable results to the ones already published are obtained (69 % capacity for LiFePO compared to the theoretical value). In the case of the 0.5 mm thick sintered solid, an outstanding performance is achieved, reaching almost the theoretical capacity (94 %) with a very high coulombic efficiency (>99 %) at 1 mA cm, results that were only obtained at much lower current densities in previous works., CONEX-Plus programme funded by Universidad CarlosIII de Madrid and the European Union’s Horizon 2020 research and innovation programme under the MarieSklodowska-Curie grant agreement No. 801538.The authors also thank the Agencia Española de Investigación/Fondo Europeo de Desarrollo Regional(FEDER/UE)for funding the project PID2019-106662RB-C43.This work has also beensupported by Comunidad de Madrid(Spain) though two project:multi annual agreement with UC3M (“Excelencia para el ProfesoradoUniversitario”– EPUC3M04)– Fifth regional research plan 2016–2020,and DROMADER-CM(Y2020/NMT6584)
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Proton conducting sulfonated polysulfone and polyphenylsulfone multiblock copolymers with improved performances for fuel cell applications

  • Swaby, Sydonne
  • Ureña, Nieves
  • Pérez-Prior, Maria T.
  • Del Río, C.
  • Várez, Alejandro
  • Sanchez, J. Y.
  • Iojoiu, C.
  • Levenfeld, Belén
A series of proton exchange membranes based on sulfonated multiblock copolymers with three polysulfone (PSU) and polyphenylsulfone (PPSU) ratios (50/50, 60/40 and 75/25) are prepared following a synthesis strategy that aims to achieve a microphase separation. A selective sulfonation of PSU blocks was observed in copolymers with a high proportion of PSU. The water uptake is higher in these materials (31% and 57% for SPES 50/50 and SPES 75/25, respectively at 60 °C) while the tensile strength was lower (56.0 MPa and 40.6 MPa for SPES 50/50 and SPES 75/25 in the H form, respectively). Ionic conductivity of SPES 75/25 membranes measured both ex situ and in situ at 80 °C is 25 and 31 mS·cm, respectively. Fuel cell tests reveal that SPES 75/25 shows the highest value for the maximum power density (670 mW·cm at 70 °C and 100% of RH) which is higher than that achieved for SPES 50/50 (400 mW·cm). In addition, the high current density obtained for SPES 75/25 (1000 mA·cm at 0.6 V and 70 °C) compared with SPES50/50 (600 mA·cm) and Nafion 112 (450 mA·cm at 75 °C) shows its promising properties as solid electrolyte in polymeric fuel cells., This work has been supported by Agencia Estatal de Investigación (AEI)/Fondo Europeo de Desarrollo Regional (FEDER/UE) the project MINECO (PID-2019-106662RB-C43). We also wish to thank the Regional Government (Comunidad de Madrid) through three Projects: 1) DROMADER-CM (Y2020/NMT6584) 2) PEM4ENERGY-CM-UC3M and 3) the Multiannual agreement with UC3M (‘‘Excelencia para el Profesorado Universitario” -EPUC3M04) - Fifth regional research plan 2016-2020. We also thank the IAAB from Universidad Carlos III de Madrid for funding the mobility grant to Université Grenoble-Alpes, Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Using Metal-Organic Framework HKUST-1 for the Preparation of High-Conductive Hybrid Membranes Based on Multiblock Copolymers for Fuel Cells

  • Gorban, Ivan
  • Ureña, Nieves
  • Pérez-Prior, Maria T.
  • Várez, Alejandro
  • Levenfeld, Belén
  • Río, Carmen del
  • Soldatov, Mikhail
Novel proton-conducting hybrid membranes consisting of sulfonated multiblock copolymer of polysulfone and polyphenylsulfone (SPES) reinforced with a HKUST-1 metal-organic framework (MOF) (5, 10, and 20 wt. %) were prepared and characterized for fuel cell applications. The presence of the MOF in the copolymer was confirmed by means of FE-SEM and EDS. The hybrid membranes show a lower contact angle value than the pure SPES, in agreement with the water uptake (WU%), i.e., by adding 5 wt. % of the MOF, this parameter increases by 20% and 40% at 30 °C and 60 °C, respectively. Additionally, the presence of the MOF increases the ion exchange capacity (IEC) from 1.62 to 1.93 mH g. Thermogravimetric analysis reveals that the hybrid membranes demonstrate high thermal stability in the fuel cell operation temperature range (<100 °C). The addition of the MOF maintains the mechanical stability of the membranes (TS > 85 MPa in the Na form). Proton conductivity was analyzed using EIS, achieving the highest value with a 5 wt. % load of the HKUST-1. This value is lower than that observed for the HKUST-1/Nafion system. However, polarization and power density curves show a remarkably better performance of the hybrid membranes in comparison to both the pure SPES and the pure Nafion membranes., This work was funded by the Agencia Estatal de Investigación (AEI)/Fondo Europeo de Desarrollo Regional (FEDER/UE), PID-2019-106662RB-C43, by the Spanish Government, MAT2016-78632-C4-3-R, by the Regional Government PEM4ENERGY-CM-UC3M funded by the call “Programa de apoyo a la realización de proyectos interdisciplinares de I + D para jóvenes investigadores de la Universidad Carlos III de Madrid 2019–2020” under the frame of the “Con-venio Plurianual Comunidad de Madrid-Universidad Carlos III de Madrid”, and by the Ministry of Science and Higher Education of the Russian Federation (State assignment in the field of scientific activity, № 0852-2020-0019)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

High-areal capacity and binder-free thick-ceramic LFP electrodes manufactured by robocasting for Li-ion batteries

  • Martínez-Cisneros, Cynthia S.
  • Ramírez, Cristina
  • Martínez-Rodríguez, Dayron
  • Belmonte, Manuel
  • Levenfeld, Belen
  • Varez, Alejandro
To address the growing demands for energy density, power, lifetime, and safety in Li-ion batteries, innovative processing techniques for high-capacity electrodes are essential. This study explores the additive manufacturing of ultra-thick LiFePO4 (LFP) electrodes (∼800 μm) using robocasting, as an alternative to traditional methods like screen printing or pressing. 3D LFP-based electrodes with cellular architectures and high mass loading (∼20 mg) are designed to enhance ion transport and energy density by increasing the surface area. Eco-friendly, aqueous-based printable inks are optimized for suitable rheological properties (viscosity, modulus, yield strength), in agreement with scalable and sustainable production. To improve mechanical strength and conductivity, 3 wt% of graphene oxide (GO) or graphene nanoplatelets (GNP) are incorporated to the ink formulation. After printing, 3D structures undergo thermal debinding and sintering to remove inactive components, yielding additive-free electrodes. Microstructural, mechanical, and electrical characterizations reveal that GO incorporation increases Vickers hardness by 50 % without compromising compressive strength. Electrochemical testing with Li4Ti5O12 (LTO) as the anode demonstrates promising performance, with LFP-GO electrodes achieving areal capacities up to 11 mA h cm−2 (21 mW h cm−2) at C/25. These results highlight the potential of robocasting to produce robust, high-performance thick electrodes for next-generation Li-ion batteries., This work has been supported by MCIN/AEI/10.13039/ 501100011033 and by “ERDF A way of making Europe” through Grant (projects PID2019-106662RBC43, PID2020-12056RJ-I00, PID2021–125427OB-I00 and PID2022-140373OB-I00) and the Madrid Government (Comunidad de Madrid-Spain) through the DROMADER- CM project (Y2020/NMT6584). APC Funding: Universidad Carlos III de Madrid (CRUE-Madro˜no 2025 Agreement., Data will be made available on request., Peer reviewed