Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 50
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Calibration of offset via bulk for Low-power HfO2 based 1T1R memristive crossbar Read-Out System

  • Mohan, Charanraj
  • Camuñas-Mesa, Luis A.
  • Vianello, Elisa
  • Periniolla, L.
  • Reita, Carlo
  • Rosa, José M. de la
  • Serrano-Gotarredona, Teresa
  • Linares-Barranco, Bernabé
Neuromorphic RRAM circuits typically need currents of several mA when many binary memristive devices are activated at the same time. This is due to the low resistance state of these devices, which increases the power consumption and limits the scalability. To overcome this limitation, it is vital to investigate how to minimize the amplitude of the read-out inference pulses sent through the crossbar lines. However, the amplitude of such inference voltage pulses will become limited by the offset voltage of read-out circuits. This paper presents a three-stage calibration circuit to compensate for offset voltage in the wordlines of a memristor-array read-out system. The proposed calibration scheme is based on adjusting the bulk voltage of one of the input differential pair MOSFETs by means of a switchable cascade of resistor ladders. This renders the possibility to obtain calibration voltage steps less than 0.1 mV by cascading a few number of stages, whose results are only limited by mismatch, temperature, electrical noise and other fabrication defects. The system is built using HfO2-based binary memristive synaptic devices on top of a 130-nm CMOS technology. Layout-extracted simulations considering technology corners, PVT variations and electrical noise are shown to validate the presented calibration scheme., This work was supported in part by the EU H2020 grants 644096 “ECOMODE” and 687299 “NeuRAM3”, by Spanish grants from the Ministry of Economy and Competitiveness – TEC2013-45638-C3-3-R (MARAGADA), TEC2015-63884-C2-1-P (COGNET) and TEC2016-75151-C3-3-R (TOGETHER) (with support from the European Regional Development Fund) and by the International Consortium of Nanotechnology of the Lloyd's Register Foundation under Grant Reference G0086. CSIC acknowledges CMP for design assembly and guidance.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Statistical Characterization of Time-Dependent Variability Defects Using the Maximum Current Fluctuation

  • Saraza-Canflanca, P.
  • Martín-Martínez, Javier
  • Castro-López, Rafael
  • Roca, Elisenda
  • Rodríguez, Rosana
  • Fernández, Francisco V.
  • Nafría, Montserrat
This article presents a new methodology to extract, at a given operation condition, the statistical distribution of the number of active defects that contribute to the observed device time-dependent variability, as well as their amplitude distribution. Unlike traditional approaches based on complex and time-consuming individual analysis of thousands of current traces, the proposed approach uses a simpler trace processing, since only the maximum and minimum values of the drain current during a given time interval are needed. Moreover, this extraction method can also estimate defects causing small current shifts, which can be very complex to identify by traditional means. Experimental data in a wide range of gate voltages, from near-threshold up to nominal operation conditions, are analyzed with the proposed methodology., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Contribución de congreso (ConferenceOutput)

Circuit reliability prediction: Challenges and solutions for the device time-dependent variability characterization roadblock

  • Nafria, M.
  • Díaz-Fortuny, Javier
  • Saraza-Canflanca, P.
  • Martín-Martínez, Javier
  • Roca, Elisenda
  • Castro-López, Rafael
  • Rodríguez, Rosana
  • Martín-Lloret, P.
  • Toro-Frias, A.
  • Mateo, D.
  • Barajas, Enrique
  • Aragones, X.
  • Fernández, Francisco V.
Copyright IEEE, The characterization of the MOSFET Time-Dependent Variability (TDV) can be a showstopper for reliability-Aware circuit design in advanced CMOS nodes. In this work, a complete MOSFET characterization flow is presented, in the context of a physics-based TDV compact model, that addresses the main TDV characterization challenges for accurate circuit reliability prediction at design time. The pillars of this approach are described and illustrated through examples., This work was supported by the VIGILANT Project (PID2019-103869RB / AEI / 10.13039/501100011033) and the TEC2016-75151-C3-R Project (AEI/FEDER, UE)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Enhanced Linearity in FD-SOI CMOS Body-Input Analog Circuits – Application to Voltage-Controlled Ring Oscillators and Frequency-Based ΣΔ ADCs

  • Ahmadi-Farsani, Javad
  • Zúñiga-González, Virginia
  • Serrano-Gotarredona, Teresa
  • Linares-Barranco, Bernabé
  • Rosa, José M. de la
This paper investigates the use of the body terminal of MOS transistors to improve the linearity of some key circuits used to implement analog and mixed-signal circuits integrated in Fully Depleted Silicon on Insulator (FD-SOI) CMOS. This technology allows to increase the body factor with respect to conventional (bulk) CMOS processes. This effect is analyzed in basic analog building blocks - such as switches, simple-stage transconductors and Voltage-Controlled Ring Oscillators (VCROs). Approximated expressions are derived for the nonlinear characteristics and harmonic distortion of some of these circuits. As an application, transistor-level simulations of two VCRO-based ΣA modulators designed in a 28-nm FD-SOI CMOS technology are shown in order to demonstrate the benefits of the presented techniques., This work was supported in part by the EU Horizon 2020 Programme under Grant 687299 NeuRAM3 and in part by the Spanish Ministry of Economy and Competitiveness (with support from the European Regional Development Fund) under Contract TEC2016-75151-C3-3-R., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

A 10-MHz BW 77.3-dB SNDR 640-MS/s GRO-Based CT MASH ΔΣ Modulator

  • Honarparvar, Mohammad
  • Rosa, José M. de la
  • Sawan, Mohamad
We present in this brief a novel multi-stage noise-shaping (MASH) 3-1 continuous-time (CT) delta-sigma modulator ( $\Delta \Sigma \text{M}$ ) with gated ring oscillator based quantizers (GROQs) in both stages of the cascade. The use of GROQs increases the linearity performance with respect to the conventional voltage controlled oscillator based quantizers (VCOQs) and allows a more robust extraction of the front-end stage quantization error in the time domain, thus making the proposed architecture more suitable to implement high-order expandable scaling-friendly MASH $\Delta \Sigma $ Ms, in which the back-end stages are implemented by mostly-digital GRO-based time-to-digital converters (TDCs). The circuit has been fabricated in a 65-nm CMOS technology with 1-V supply voltage, and it operates at 640-MHz sampling frequency to digitize 10-MHz signals. To the best of the authors' knowledge, this is the first reported experimental validation of a GRO-based CT MASH $\Delta \Sigma \text{M}$ , featuring a 79.8-dB signal to noise ratio (SNR) at -2.2-dBFS, a 77.3-dB signal to (noise + distortion) ratio (SNDR) at -4-dBFS and a dynamic range (DR) of 81.7 dB, with a power consumption of 12-mW. These metrics demonstrate state-of-the-art performance with a DR-based Schreier FOM of 170.9 dB., The authors acknowledge the Natural Sciences and Engineering Research Council of Canada for the support and CMC Microsystems for the design tools. This work was also partially supported by the Spanish Min. of Econ. and Comp. (and European RDF) under contract TEC2016-75151-C3-3-R., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Contribución de congreso (ConferenceOutput)

An IC Array for the Statistical Characterization of Time-Dependent Variability of Basic Circuit Blocks

  • Martin-Lloret, P.
  • Núñez, Juan
  • Roca, Elisenda
  • Castro-López, Rafael
  • Martín-Martínez, Javier
  • Rodríguez, Rosana
  • Nafria, M.
  • Fernández, Francisco V.
Talk delivered in International Conference on Synthesis, Modeling, Analysis and Simulation Methods, and Applications to Circuit Design (SMACD) in Lausanne (Switzerland), 15-18 July 2019. © 2019 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes, creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., This paper presents an integrated circuit (IC) array whose purpose is to observe, quantify and characterize the impact of time-dependent variability effects, like aging, in several widely used digital and analog circuit blocks. With the increasing interest that this kind of mechanism has attracted in the last years, for its potential impact in the reliability of ultra-scaled integrated circuits, it is only relevant that appropriate measures are taken to find out how it can be included (and thus mitigated) in the design process of such integrated circuits. And, while substantial literature exists that covers the device level, time-dependent variability at circuit level has not been as equally studied. This work complements our previous efforts in providing a holistic approach to Reliability-Aware Design: from statistical characterization and modeling at device-level, to simulation, and into optimization-based design with reliability considerations, the array presented here provides one more step towards a thorough and accurate understanding of how time-dependent variability works at the circuit level., This work was supported in part by the TEC2016-75151-C3-R Project (funded by the Spanish MINECO and ERDF)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Contribución de congreso (ConferenceOutput)

TiDeVa: A Toolbox for the Automated and Robust Analysis of Time-Dependent Variability at Transistor Level

  • Saraza-Canflanca, P.
  • Díaz-Fortuny, Javier
  • Castro-López, Rafael
  • Roca, Elisenda
  • Martín-Martínez, Javier
  • Rodríguez, Rosana
  • Nafria, M.
  • Fernández, Francisco V.
Talk delivered in International Conference on Synthesis, Modeling, Analysis and Simulation Methods, and Applications to Circuit Design (SMACD) in Lausanne (Switzerland), 15-18 July 2019. © 2019 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes, creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., Time-Dependent Variability has attracted increasing interest in the last years. In particular, time-dependent phenomena such as Bias Temperature Instability, Hot Carrier Injection and Random Telegraph Noise can have a large impact on circuit reliability, and must be therefore characterized and modeled. For technologies in the nanometer range, these phenomena reveal a stochastic behavior and must be characterized in a massive manner, with enormous amounts of data being generated in each measurement. In this work, a novel tool with a user-friendly interface, which allows the robust and fully-automated parameter extraction for RTN, BTI and HCI experiments, is presented., This work has been supported in part by the TEC2016-75151-C3-R Project (funded by the Spanish MINECO and ERDF) and by the P12-TIC-1481 Project (funded by Junta de Andalucía)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Contribución de congreso (ConferenceOutput)

Synthesis of mm-Wave circuits using-EM-simulated passive structure libraries

  • Passos, Fábio
  • Roca, Elisenda
  • Castro-López, Rafael
  • Horta, N.
  • Fernández, Francisco V.
Talk delivered in International Conference on Synthesis, Modeling, Analysis and Simulation Methods, and Applications to Circuit Design (SMACD) in Lausanne (Switzerland), 15-18 July 2019. © 2019 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes, creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., Millimeter-wave circuit design is extremely complex and time-consuming. One of the reasons is the dependence on electromagnetic simulators used to accurately predict the performance of the high amount of passive structures that compose such circuits. Also, achieving optimal performances is not trivial in the millimeter-wave regime. Although synthesis methodologies can aid the designer to achieve optimal circuit performances, the usage of electromagnetic simulators is prohibitive in such methodologies due to efficiency issues. In this work, a new synthesis methodology is presented where the accuracy of electromagnetic simulations can be included without losing efficiency., This work is funded by FCT/MEC through national funds and when applicable co-funded by FEDER – PT2020 partnership agreement under the project UID/EEA/50008/2019 and by the TEC2016-75151-C3-3-R Project (funded by the Spanish Ministry of Science, Innovation and Universities and ERDF)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Contribución de congreso (ConferenceOutput)

Experimental Characterization of Time-Dependent Variability in Ring Oscillators

  • Núñez, Juan
  • Roca, Elisenda
  • Castro-López, Rafael
  • Martín-Martínez, Javier
  • Rodríguez, Rosana
  • Nafria, M.
  • Fernández, Francisco V.
Talk delivered in International Conference on Synthesis, Modeling, Analysis and Simulation Methods, and Applications to Circuit Design (SMACD) in Lausanne (Switzerland), 15-18 July 2019. © 2019 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes, creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., Reliability in CMOS-based integrated circuits has always been a critical concern. In today's ultra-scaled technologies, a time-varying kind of variability has raised that, on top of the well-known time-zero variability, threatens to shorten the lifetime of integrated circuits, both analog and digital. Effects like Bias Temperature Instability and Hot Carriers Injection need to be studied, characterized and modeled to include, and, thus, mitigate, their impact in the design of CMOS integrated circuits. This paper presents an array-based integrated circuit whose purpose is precisely that: to observe, quantify and characterize the impact of time-dependent variability effects in a specific kind of circuits: Ring Oscillators., This work has been funded by Ministerio de Economía y Competitividad del Gobierno de España with support from ERDF (Projects TEC2016-75151-C3-R, TEC2017-87052-P)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Contribución de congreso (ConferenceOutput)

A New Time Efficient Methodology for the Massive Characterization of RTN in CMOS Devices

  • Pedreira, G.
  • Martín-Martínez, Javier
  • Díaz-Fortuny, Javier
  • Saraza-Canflanca, P.
  • Rodríguez, Rosana
  • Castro-López, Rafael
  • Roca, Elisenda
  • Fernández, Francisco V.
  • Nafria, M.
Talk delivered at the IEEE International Reliability Physics Symposium (IRPS) in Monterrey, California (USA), March 31– April 4, 2019. © 2019 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes, creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., In this work a new method to characterize Random Telegraph Noise (RTN) in a large number of devices is presented. The method is applied to the RTN characterization of nearly 800 pMOS transistors and compared with conventional approaches. The results presented here show that the new method, which requires the measurement of each device only in two instants, can hugely reduce the measurement time needed for the statistical characterization of RTN., This work was supported by Spanish AEI and ERDF under Project TEC2016-75151-C3-R. The work of G. Pedreira, J. Diaz-Fortuny and P. Saraza-Canflanca was supported by AEI under grants BES-2017-081462, BES-2014-067855 and BES- 2017-080160 respectively., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Contribución de congreso (ConferenceOutput)

Generation of Lifetime-Aware Pareto-Optimal Fronts Using a Stochastic Reliability Simulator

  • Toro-Frias, A.
  • Saraza-Canflanca, P.
  • Passos, Fábio
  • Martin-Lloret, P.
  • Castro-López, Rafael
  • Roca, Elisenda
  • Martín-Martínez, Javier
  • Rodríguez, Rosana
  • Nafria, M.
  • Fernández, Francisco V.
Talk delivered at the 2019 Design, Automation & Test in Europe Conference & Exhibition (DATE) in Florence (Italy), 25 – 29 March 2019. © 2019 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes, creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., Process variability and time-dependent variability have become major concerns in deeply-scaled technologies. Two of the most important time-dependent variability phenomena are Bias Temperature Instability (BTI) and Hot-Carrier Injection (HCI), which can critically shorten the lifetime of circuits. Both BTI and HCI reveal a discrete and stochastic behavior in the nanometer scale, and, while process variability has been extensively treated, there is a lack of design methodologies that address the joint impact of these two phenomena on circuits. In this work, an automated and time-efficient design methodology that takes into account both process and time-dependent variability is presented. This methodology is based on the utilization of lifetime-aware Pareto-Optimal Fronts (POFs). The POFs are generated with a multi-objective optimization algorithm linked to a stochastic simulator. Both the optimization algorithm and the simulator have been specifically tailored to reduce the computational cost of the accurate evaluation of the impact on a circuit of both sources of variability., This work has been supported by the TEC2016-75151-C3-R Project (funded by the Spanish MINECO and ERDF). Pablo Sarazá Canflanca acknowledges MINECO for supporting his research activity through the predoctoral grant BES-2017-080160., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Contribución de congreso (ConferenceOutput)

New method for the automated massive characterization of Bias Temperature Instability in CMOS transistors

  • Saraza-Canflanca, P.
  • Díaz-Fortuny, Javier
  • Castro-López, Rafael
  • Roca, Elisenda
  • Martín-Martínez, Javier
  • Rodríguez, Rosana
  • Nafria, M.
  • Fernández, Francisco V.
Talk delivered at the 2019 Design, Automation & Test in Europe Conference & Exhibition (DATE), in Florence (Italy), 25 – 29 March 2019. © 2019 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes, creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., Bias Temperature Instability has become a critical issue for circuit reliability. This phenomenon has been found to have a stochastic and discrete nature in nanometer-scale CMOS technologies. To account for this random nature, massive experimental characterization is necessary so that the extracted model parameters are accurate enough. However, there is a lack of automated analysis tools for the extraction of the BTI parameters from the extensive amount of generated data in those massive characterization tests. In this paper, a novel algorithm that allows the precise and fully automated parameter extraction from experimental BTI recovery current traces is presented. This algorithm is based on the Maximum Likelihood Estimation principles, and is able to extract, in a robust and exact manner, the threshold voltage shifts and emission times associated to oxide trap emissions during BTI recovery, required to properly model the phenomenon., This work has been supported by the TEC2016-75151-C3-R Projects (funded by the Spanish MINECO and ERDF). Javier Díaz Fortuny acknowledges MINECO for supporting his research activity through the FPI grant BES-2014-067855. Pablo Sarazá Canflanca acknowledges MINECO for supporting his research activity through the predoctoral grant BES-2017-080160., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Contribución de congreso (ConferenceOutput)

Improving the reliability of SRAM-based PUFs in the presence of aging

  • Saraza-Canflanca, P.
  • Carrasco-Lopez, H.
  • Brox, Piedad
  • Castro-López, Rafael
  • Roca, Elisenda
  • Fernández, Francisco V.
Talk delivered at the 2020 conference 15th Design & Technology of Integrated Systems in Nanoscale Era (DTIS), Marrakesh (Morocco), April 1-3, 2020. © 2020 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes, creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., The utilization of power-up values in SRAM cells for the generation of PUF responses has been widely studied. It is important that the cells used for this purpose are stable, i.e., the cells must have a strong tendency towards one of the two possible values ('0' or '1'). Some methods have been presented that aim at increasing the reliability of this type of PUFs by selecting the strongest cells among a set of them. However, they feature some drawbacks, either in terms of their practical feasibility or of their actual effectiveness selecting the strongest cells in different scenarios. In this work, the experimental results obtained for a new method to classify the cells according to their strength are presented and discussed. The technique overcomes some of the drawbacks that the previous methods present. In particular, it is experimentally demonstrated that the technique presented in this work outstands in selecting SRAM cells that are very robust against circuit degradation, which translates into the construction of reliable SRAM-based PUFs., This work was supported by the TEC2016-75151-C3-R Project (funded by the Spanish MINECO and ERDF). Pablo Sarazá Canflanca acknowledges MINECO for supporting his research activity through the predoctoral grant BES-2017-080160., Peer reviewed
Recercat. Dipósit de la Recerca de Catalunya
Publication Contribución de congreso (ConferenceOutput)

Modem gain-cell memories in advanced technologies

  • Amat Bertran, Esteve
  • Canal Corretger, Ramon
  • Rubio Sola, Jose Antonio
With the advent of the slowdown in DRAM capacitor scaling [1] and the increased reliability problems of traditional 6T SRAM memories [2], industry and academia have looked for alternative memory cells. Among those, gain- cells have attracted significant attention due to their smaller size (compared to SRAM) and non-destructive read operation (compared to DRAM) as well as considerable low power and reasonable robustness. This paper first summarizes the available evidences of SRAM and eDRAM in commercial and test chips. Then, it analyzes the performance, reliability and scaling of eDRAM gain-cells in 10 and 7 nm FinFET technology; as well as above and below VT (i.e. sub-threshold)., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Voltage divider for self-limited analog state programing of memristors

  • Gomez, Jorge
  • Vourkas, Ioannis
  • Abusleme, Angel
  • Sirakoulis, Georgios
  • Rubio Sola, Jose Antonio
© 2020 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes,creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., Resistive switching devices - memristors - present a tunable, incremental switching behavior. Tuning their state accurately, repeatedly and in a wide range, makes memristors well-suited for multi-level (ML) resistive memory cells and analog computing applications. In this brief, the tuning approach based on a memristor-resistor voltage divider (VD) is validated here experimentally using commercial memristors from Knowm Inc. and a custom circuit. Rapid and controllable multi-state SET tuning is shown with an appreciable range of different resistance values obtained as a function of the amplitude of the applied voltage pulse. The efficiency of the VD is finally compared against an adaptive pulse-based tuning protocol, in terms of circuit overhead, tuning precision, tuning time, and energy consumption, qualifying as a simple hardware solution for fast, reliable, and energy-efficient ML resistance tuning., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

A versatile CMOS transistor array IC for the statistical characterization of time-zero variability, RTN, BTI, and HCI

  • Diaz Fortuny, Javier
  • Martin Martínez, Javier
  • Rodríguez Martínez, Rosana
  • Castro López, Rafael
  • Roca Moreno, Elisenda
  • Aragonès Cervera, Xavier
  • Barajas Ojeda, Enrique
  • Mateo Peña, Diego
  • Fernández Fernández, Francisco V.
  • Nafría Maqueda, Montserrat
© 2018 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes,creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., Statistical characterization of CMOS transistor variability phenomena in modern nanometer technologies is key for accurate end-of-life prediction. This paper presents a novel CMOS transistor array chip to statistically characterize the effects of several critical variability sources, such as time-zero variability (TZV), random telegraph noise (RTN), bias temperature instability (BTI), and hot-carrier injection (HCI). The chip integrates 3136 MOS transistors of both pMOS and nMOS types, with eight different sizes. The implemented architecture provides the chip with a high level of versatility, allowing all required tests and attaining the level of accuracy that the characterization of the above-mentioned variability effects requires. Another very important feature of the array is the capability of performing massively parallel aging testing, thus significantly cutting down the time for statistical characterization. The chip has been fabricated in a 1.2-V, 65-nm CMOS technology with a total chip area of 1800 x 1800 µm²., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publication Contribución de congreso (ConferenceOutput)

Variability-tolerant memristor-based ratioed logic in crossbar array

  • Escudero López, Manuel
  • Rubio Sola, Jose Antonio
  • Moll Echeto, Francisco de Borja
  • Vourkas, Ioannis
The final publication is available at ACM via http://dx.doi.org/10.1145/3232195.3232213, The advent of the first TiO2-based memristor in 2008 revived the scientific interest both from academia and industry for this de- vice technology, with several emerging applications including that of logic circuits. Several memristive logic families have been pro- posed, each with different attributes, in the current quest for energy- efficient computing systems of the future. However, limited en- durance of memristor devices and variations (both cycle-to-cycle and device-to-device) are important parameters to be considered in the evaluation of such logic families. In this work we build upon an accurate physics-based model of a bipolar metal-oxide resistive RAM device (supporting parasitics of the device structure and va- riability of switching voltages and resistance states) and use it to show how performance of memristor-based logic circuits can de degraded owing to both variability and state-drift impact. Based on previous work on CMOS-like memristive logic circuits, we propose a memristive ratioed logic scheme, which is crossbar-compatible, i.e. suitable for in-/near-memory computing, and tolerant to device variability, while also it does not affect the device endurance since computations do not involve switching the memristor states. As a figure of merit, we compare such new logic scheme with MAGIC, focusing on the universal NOR logic gate., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publication Contribución de congreso (ConferenceOutput)

An on-line test strategy and analysis for a 1T1R crossbar memory

  • Escudero, Manel
  • Moll Echeto, Francisco de Borja
  • Rubio Sola, Jose Antonio
  • Vourkas, Ioannis
© 2017 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes,creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., Memristors are emerging devices known by their nonvolability, compatibility with CMOS processes and high density in circuits density in circuits mostly owing to the crossbar nanoarchitecture. One of their most notable applications is in the memory system field. Despite their promising characteristics and the advancements in this emerging technology, variability and reliability are still principal issues for memristors. For these reasons, exploring techniques that check the integrity of circuits is of primary importance. Therefore, this paper proposes a method to perform an on-line test capable to detect a single failure inside the memory crossbar array., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Exploring the “resistance change per energy unit” as universal performance parameter for resistive switching devices

  • Gómez Mir, Jorge Tomás
  • Vourkas, Ioannis
  • Abusleme, Angel
  • Rodríguez Martínez, Rosana
  • Martin Martínez, Javier
  • Nafría Maqueda, Montserrat
  • Rubio Sola, Jose Antonio
© <2019> Elsevier. This manuscript version is made available under the CC-BY-NC-ND 4.0 license http://creativecommons.org/licenses/by-nc-nd/4.0/, Resistive switching (RS) device (memristor) technology is continuously maturing towards industrial establishment. There are RS devices that demonstrate an “incremental” (analog) switching behavior, whereas others change their state in a binary form. The final achieved resistance is generally a function of the applied pulse characteristics, i.e. amplitude and duration. However, variability —both from device to device but also from cycle to cycle— and the stochastic nature of internal RS phenomena, still hold back any universal tuning approach based solely on these two magnitudes, making also difficult the qualitative comparison between devices with different material compounds owing to the required SET/RESET voltages being dependent on the biasing conditions. In this work we demonstrate experimentally using commercial RS devices from Knowm Inc. that the switching energy is very insensitive to the biasing conditions. We explored experimentally the SET-RESET behavior of bipolar RS devices from the energy point of view. We figured out the quantitative effect of the injected energy to the resistive state of the devices, and proposed an analytical model to explain our observations in the energy consumed by the device during the switching process. Our results lay the foundations for the definition of “resistance change per energy unit” as a performance parameter for this emerging device technology., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publication Contribución de congreso (ConferenceOutput)

Coupled physarum-inspired memristor oscillators for neuron-like operations

  • Ntinas, Vasileios
  • Vourkas, Ioannis
  • Sirakoulis, Georgios Ch.
  • Adamatzky, Andrew
  • Rubio Sola, Jose Antonio
© 2018 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes,creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., Unconventional computing has been studied intensively, even after the appearance of CMOS technology. Currently, it has returned to the spotlight because CMOS is about to reach its physical limits, given that the constant demand for more computational power requires for novel unconventional computing solutions. In this area, the oscillatory internal motion mechanism of slime mould, namely Physarum Polycephalum, could serve as an alternative concept for the design and development of electronic circuits that exploit the memristive dynamics and simple LC contours to deliver solutions for computationally hard to be solved problems. In this direction, this work presents how bio-inspired memristive LC oscillators with a coupling capacitor can be synchronized to perform the functionalities of a biological neuron, also able to execute more complex computations, aiming to model biological neural systems much more advanced than the neuron-less slime mould biological organism. This work proposes a connection between the function mechanism of a simple biological organism and that of complex biological systems, made in a plausible and sufficient manner, towards unconventional computation with memristors., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publication Contribución de congreso (ConferenceOutput)

On the variability-aware design of memristor-based logic circuits

  • Escudero López, Manuel
  • Vourkas, Ioannis
  • Rubio Sola, Jose Antonio
  • Moll Echeto, Francisco de Borja
© 2018 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes,creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., Ever since the advent of the first TiO 2 -based memristor and the respective linear model published by Hewlett-Packard Labs, several behavioral models of memristors have been published. Such models capture the fundamental characteristics of resistive switching behavior through simple equations and rules, so they received a lot of attention and contributed significantly to the fast progress of research in this new and emerging device technology field. However, while this technology is maturing, accurate physics-based models are being developed, which go deeper into the device dynamics and capture more details than what just would be the fundamentals: i.e. parasitics of the device structure, variability of threshold voltages and resistance states, temperature dependency, dynamic current fluctuations, etc. In this work we build upon such a physics-based model of a bipolar metal-oxide resistive RAM device, showing how to take into account device variability and its significance in evaluation of processing circuits. With the Cadence Virtuoso suite, we focus on a family of memristive logic gate implementations showing that read & write errors can emerge due to both variability and state-drift impact, features rarely seen so far in results shown in other relevant published works., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publication Contribución de congreso (ConferenceOutput)

Memristive cellular automata for modeling of epileptic brain activity

  • Karamani, Rafallia
  • Fyrigos, Iosif
  • Ntinas, Vasileios
  • Vourkas, Ioannis
  • Sirakoulis, Georgios Ch.
  • Rubio Sola, Jose Antonio
© 2018 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes,creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., Cellular Automata (CA) is a nature-inspired and widespread computational model which is based on the collective and emergent parallel computing capability of units (cells) locally interconnected in an abstract brain-like structure. Each such unit, referred as CA cell, performs simplistic computations/processes. However, a network of such identical cells can exhibit nonlinear behavior and be used to model highly complex physical phenomena and processes and to solve problems that are highly complicated for conventional computers. Brain activity has always been considered one of the most complex physical processes and its modeling is of utter importance. This work combines the CA parallel computing capability with the nonlinear dynamics of the memristor, aiming to model brain activity during the epileptic seizures caused by the spreading of pathological dynamics from focal to healthy brain regions. A CA-based confrontation extended to include long-range interactions, combined with the recent notion of memristive electronics, is thus proposed as a modern and promising parallel approach to modeling of such complex physical phenomena. Simulation results show the efficiency of the proposed design and the appropriate reproduction of the spreading of an epileptic seizure., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Shortest path computing in directed graphs with weighted edges mapped on random networks of memristors

  • Fernández Moya, Carlos
  • Vourkas, Ioannis
  • Rubio Sola, Jose Antonio
Electronic version of an article published as [Fernandez, Carlos, Ioannis Vourkas, and Antonio Rubio. "Shortest Path Computing in Directed Graphs with Weighted Edges Mapped on Random Networks of Memristors." Parallel Processing Letters 30.01 (2020): 2050002] [https://doi.org/10.1142/S0129626420500024] © [copyright World Scientific Publishing Company] [https://www.worldscientific.com/worldscinet/ppl], To accelerate the execution of advanced computing tasks, in-memory computing with resistive memory provides a promising solution. In this context, networks of memristors could be used as parallel computing medium for the solution of complex optimization problems. Lately, the solution of the shortest-path problem (SPP) in a two-dimensional memristive grid has been given wide consideration. Some still open problems in such computing approach concern the time required for the grid to reach to a steady state, and the time required to read the result, stored in the state of a subset of memristors that represent the solution. This paper presents a circuit simulation-based performance assessment of memristor networks as SPP solvers. A previous methodology was extended to support weighted directed graphs. We tried memristor device models with fundamentally different switching behavior to check their suitability for such applications and the impact on the timely detection of the solution. Furthermore, the requirement of binary vs. analog operation of memristors was evaluated. Finally, the memristor network-based computing approach was compared to known algorithmic solutions to the SPP over a large set of random graphs of different sizes and topologies. Our results contribute to the proper development of bio-inspired memristor network-based SPP solvers., This work was supported by the Chilean research grants CONICYT REDES ETAPA INICIAL Convocatoria 2017 No. REDI170604, CONICYT BASAL FB0008, and by the Spanish MINECO and ERDF (TEC2016-75151-C3-2-R)., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Experimental time evolution study of the HFO-based IMPLY gate operation

  • Maestro, M
  • Marin-Martinez, J.
  • Crespo-Yepes, A.
  • Escudero, Manel
  • Rodriguez, R.
  • Nafría Maqueda, Montserrat
  • Aymerich, X.
  • Rubio Sola, Jose Antonio
© 2018 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes,creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., In the last years, memristor devices have been proposed as key elements to develop a new paradigm to implement logic gates. In particular, the memristor-based material implication (IMPLY) gate has been presented as a potential powerful basis for logic applications. In the literature, the IMPLY operation has been widely simulated but most of the efforts have been just focused on accomplishing its truth table, only considering the initial and final states of the gate. However, a complete understanding of the time evolution between states is still missing and barely reported yet. In this work, the time evolution of memristor involved in an IMPLY gate are studied in detail for every case of the gate. Furthermore, the impact on IMPLY gate operation of the internal resistor connected in series with the memristors of the IMPLY gate is included., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publication Contribución de congreso (ConferenceOutput)

A pragmatic gaze on stochastic resonance based variability tolerant memristance

  • Ntinas, Vasileios
  • Rubio Sola, Jose Antonio
  • Sirakoulis, Georgios Ch.
  • Cotofana, Sorin
© 2019 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes,creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., Stochastic Resonance (SR) is a nonlinear system specific phenomenon, which was demonstrated to lead to system unexpected (counter-intuitive) performance improvements under certain noise conditions. Memristor, on the other hand, is a fundamentally nonlinear circuit element, thus susceptible to benefit from SR, which recently came in the spotlight of the emerging technologies potential candidates. However, at this time, the variability exhibited by manufactured memristor devices within the same array constitutes the main hurdle in the road towards the commercialisation of memristor-based memories and/or computing units. Thus, in this paper, memristor SR effects are explored, assuming various memristor models, and SR-based memristance range enhancement, tolerant to device-to-device variability, is demonstrated. Our experiments reveal that SR can induce significant R MAX /R MIN ratio increase under up to 60% variability, getting as high as 3.4× for 29 dBm noise power., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publication Contribución de congreso (ConferenceOutput)

Body bias generators for ultra low voltage circuits in FDSOI technology

  • Justo, Diego
  • Nunes Cavalheiro, David
  • Moll Echeto, Francisco de Borja
Electronic circuits powered at ultra low voltages (300 mV and below) are desirable for their low energy and power consumption. However, the performance at such low power voltage is severely degraded. FDSOI technology, with its large range of body bias voltages can counteract the performance loss by applying forward body bias to the circuit. Charge pump circuits can be used to generate positive and negative body bias voltages integrated on the chip. This paper studies the main challenges in the design of such circuits operating at 300 mV to reach body bias voltages of more than 1 V., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Experimental study of artificial neural networks using a digital memristor simulator

  • Ntinas, Vasileios
  • Vourkas, Ioannis
  • Abusleme, Angel
  • Sirakoulis, Georgios
  • Rubio Sola, Jose Antonio
© 2018 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes,creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., This paper presents a fully digital implementation of a memristor hardware simulator, as the core of an emulator, based on a behavioral model of voltage-controlled threshold-type bipolar memristors. Compared to other analog solutions, the proposed digital design is compact, easily reconfigurable, demonstrates very good matching with the mathematical model on which it is based, and complies with all the required features for memristor emulators. We validated its functionality using Altera Quartus II and ModelSim tools targeting low-cost yet powerful field programmable gate array (FPGA) families. We tested its suitability for complex memristive circuits as well as its synapse functioning in artificial neural networks (ANNs), implementing examples of associative memory and unsupervised learning of spatio-temporal correlations in parallel input streams using a simplified STDP. We provide the full circuit schematics of all our digital circuit designs and comment on the required hardware resources and their scaling trends, thus presenting a design framework for applications based on our hardware simulator., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Memristive logic in crossbar memory arrays: Variability-aware design for higher reliability

  • Escudero López, Manuel
  • Vourkas, Ioannis
  • Rubio Sola, Jose Antonio
  • Moll Echeto, Francisco de Borja
© 2019 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes,creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., The advent of the first TiO 2 -based memristor in 2008 revived the scientific interest both from academia and industry for this device technology and has so far led to several emerging applications including logic and in-memory computing. Several memristive logic families have been proposed in the current quest for energy-efficient future computing systems. However, the limited device endurance and variability (both cycle-to-cycle and device-to-device) are important parameters to be considered in the assessment of logic operations. In this work, we used an accurate physics-based model of a bipolar memristor (supporting parasitics of the device structure and variability of switching voltages and resistance states) and demonstrate that performance of memristor-based in-memory computations can de degraded owing to both variability and state drift impact, if such features are not properly considered in the design flow. Inspired on pseudo-NMOS ratioed logic and based upon a previous CMOS-like logic scheme, we propose a crossbar-compatible memristive ratioed logic style which is tolerant to device variability and does not affect device endurance as computations do not involve conditional switching of memristors. Using the Cadence Virtuoso suite, we compare this logic scheme with MAGIC and CNIMP approaches, focusing on the universal NOR gate and more complex logic functions., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Alternative memristor-based interconnect topologies for fast adaptive synchronization of chaotic circuits

  • Escudero López, Manuel
  • Vourkas, Ioannis
  • Rubio Sola, Jose Antonio
© 2020 Elsevier. This manuscript version is made available under the CC-BY-NC-ND 4.0 license http://creativecommons.org/licenses/by-nc-nd/4.0/, Resistive switching devices (memristors) constitute an emerging device technology promising for a vari- ety of applications that are currently being studied. In this context, the use of memristors as coupling el- ements of the dynamics of chaotic circuits for adaptive synchronization purposes, was recently proposed and the passive crossbar array was evaluated as target interconnect medium. Nonetheless, memristors may suffer from defects and degradation. Therefore, this work evaluates the impact of memristor switch- ing faults in an adaptive chaotic synchronization scheme, exploring at the same time the fault-tolerance of the crossbar architecture. Moreover, inspired from our observations in the stuck-at-OFF fault analy- sis of the memristive crossbar, some alternative scalable memristive interconnect patterns are suggested, whose performance is found independent of the number of interconnected chaotic circuits, requiring a much smaller number of total memristors than the crossbar array. All simulations are based on an ac- curate physics-based model of a bipolar memristor with filamentary switching mechanism. Based on our results, using the alternative topologies instead of the crossbar array leads to significant savings in the synchronization time that increase with the number of interconnected chaotic units, at the cost of more limited scaling capability and fault-tolerance., This work was supported in part by the Chilean research Grants ANID REDES ETAPA INICIAL 2017 No. REDI170604, ANID FONDECYT INICIACION 11180706, ANID BASAL FB0008, and by the Spanish MINECO and ERDF under Grant TEC2016-75151-C3-2-R., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publication Contribución de congreso (ConferenceOutput)

Analysis of body bias and RTN-induced frequency shift of low voltage ring oscillators in FDSOI technology

  • Barajas Ojeda, Enrique
  • Aragonès Cervera, Xavier
  • Mateo Peña, Diego
  • Moll Echeto, Francisco de Borja
  • Rubio Sola, Jose Antonio
  • Martin Martínez, Javier
  • Rodríguez Martínez, Rosana
  • Porti Pujal, Marc
  • Nafría Maqueda, Montserrat
  • Castro López, Rafael
  • Roca Moreno, Elisenda
  • Fernandez, Francisco V.
Electronic circuits powered at ultra low voltages (500 mV and below) are desirable for their low energy and power consumption. However, RTN (Random Telegraph Noise)-induced threshold voltage variations become very significant at such supply voltages. This paper evaluates the impact of RTN on additional jitter in a ring oscillator. Since FDSOI allows a large range of body bias voltages, this work studies how body biasing affects the oscillation frequency but also the jitter effects. The impact of RTN in NMOS and PMOS devices on frequency as well as the levels of supplementary jitter introduced by RTN are evaluated and compared with classical device noise., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publication Contribución de congreso (ConferenceOutput)

Aging in CMOS RF linear power amplifiers: experimental comparison and modeling

  • Aragonès Cervera, Xavier
  • Mateo Peña, Diego
  • Barajas Ojeda, Enrique
  • Crespo-Yepes, A.
  • Rodríguez Martínez, Rosana
  • Martin Martínez, Javier
  • Nafría Maqueda, Montserrat
This paper characterizes experimentally the aging degradation experienced by two different 2.45 GHz power amplifier circuits of similar performance, implemented in a 65 nm CMOS technology. Results demonstrate the importance of the topology selection in order to guarantee robustness against aging effects, and thus the need to predict MOS parameter degradation during the design phase, accounting for the actual DC and RF operation conditions. For that purpose, we propose a semi-empirical compact model that, based on the RMS equivalent voltages at the transistor terminals during circuit operation, can provide an estimation of the aging degradation., Peer Reviewed, Postprint (published version)
Dipòsit Digital de Documents de la UAB
Publication Artículo científico (JournalArticle)

Self-organizing neural networks based on OxRAM devices under a fully unsupervised training scheme

  • Pedro, Marta|||0000-0003-0317-7373
  • Martin-Martinez, J.|||0000-0001-5938-5898
  • Maestro Izquierdo, Marcos|||0000-0002-8940-9050
  • Rodriguez, R.|||0000-0002-4565-6703
  • Nafria, Montserrat|||0000-0002-9549-2890
A fully-unsupervised learning algorithm for reaching self-organization in neuromorphic architectures is provided in this work. We experimentally demonstrate spike-timing dependent plasticity (STDP) in Oxide-based Resistive Random Access Memory (OxRAM) devices, and propose a set of waveforms in order to induce symmetric conductivity changes. An empirical model is used to describe the observed plasticity. A neuromorphic system based on the tested devices is simulated, where the developed learning algorithm is tested, involving STDP as the local learning rule. The design of the system and learning scheme permits to concatenate multiple neuromorphic layers, where autonomous hierarchical computing can be performed.
Dipòsit Digital de Documents de la UAB
Publication Artículo científico (JournalArticle)

Aging in CMOS RF linear power amplifiers, an experimental study

  • Nafria, Montserrat|||0000-0002-9549-2890
  • Martin-Martinez, J.|||0000-0001-5938-5898
  • Crespo-Yepes, A.|||0000-0003-4618-651X
  • Rodriguez, R.|||0000-0002-4565-6703
  • Barajas, Enrique|||0000-0002-2072-2268
  • Mateo, Diego|||0000-0001-5996-9092
  • Aragones, Xavier|||0000-0003-1352-8675
An extensive experimental analysis of the HCI and BTI aging effects on RF linear power amplifiers (PA) is presented in this paper. Two different 2.45 GHz PA topologies have been implemented in a CMOS 65 nm technology, one based on a classical common-source (CS) and choke inductor, another one based on a complementary current-reuse (CR) circuit, both of them producing similar gain and output 1-dB compression point (P-1dB). These circuits have been stressed to produce accelerated aging degradation, by applying increasing supply (VDD) voltages, or increasing RF input powers (PIN). The degradation on the transistor parameters (threshold voltage and mobility), DC bias point (IDC current) and RF performance (gain, matching, compression point) have been simultaneously measured. This has allowed to observe how the reduced transistor degradation in CR PA results in a higher robustness in its RF parameters, compared to CS PA circuit. The equivalent RMS voltages have been proposed as an observable metric to assess the combined DC+RF stress in a PA circuit. This has been applied to a semi-analytical model, thus providing comprehension of the link between the conditions under which a circuit is operated, the degradation of the transistor parameters, and the effects on the DC current and RF performance.
Dipòsit Digital de Documents de la UAB
Publication Artículo científico (JournalArticle)

Flexible setup for the measurement of CMOS time-dependent variability with array-based integrated circuits

  • Nafria, Montserrat|||0000-0002-9549-2890
  • Martin-Martinez, J.|||0000-0001-5938-5898
  • Rodriguez, R.|||0000-0002-4565-6703
  • Diaz-Fortuny, Javier|||0000-0002-8186-071X
  • Saraza-Canflanca, Pablo|||0000-0003-2155-8305
  • Castro-Lopez, Rafael|||0000-0002-6247-3124
  • Roca, Elisenda|||0000-0001-6260-6495
  • Fernandez, Francisco V.|||0000-0001-8682-2280
This paper presents an innovative and automated measurement setup for the characterization of variability effects in CMOS transistors using array-based integrated circuits (ICs), through which a better understanding of CMOS reliability could be attained. This setup addresses the issues that come with the need for a trustworthy statistical characterization of these effects: testing a very large number of devices accurately but, also, in a timely manner. The setup consists of software and hardware components that provide a user-friendly interface to perform the statistical characterization of CMOS transistors. Five different electrical tests, comprehending time-zero and time-dependent variability effects, can be carried out. Test preparation is, with the described setup, reduced to a few seconds. Moreover, smart parallelization techniques allow reducing the typically time-consuming aging characterization from months to days or even hours. The scope of this paper thus encompasses the methodology and practice of measurement of CMOS time-dependent variability, as well as the development of appropriate measurement systems and components used in efficiently generating and acquiring the necessary electrical signals.
Dipòsit Digital de Documents de la UAB
Publication Artículo científico (JournalArticle)

Exploiting the KPFM capabilities to analyze at the nanoscale the impact of electrical stresses on OTFTs properties

  • Ruiz Flores, Ana|||0000-0002-2475-7353
  • Claramunt, Sergi|||0000-0002-2888-7825
  • Crespo-Yepes, A.|||0000-0003-4618-651X
  • Porti i Pujal, Marc|||0000-0001-7438-3823
  • Nafria, Montserrat|||0000-0002-9549-2890
  • Xu, H.
  • Liu, C.
  • Wu, Q.
Two different Kelvin Probe Force Microscopy (KPFM) measurement configurations have been combined to evaluate at the nanoscale the effects of an electrical stress on Organic Thin Film Transistors (OTFTs) properties. As an example, Channel Hot Carrier (CHC) degradation has been induced to provoke some damage in the studied devices. The results show that the use of the two KPFM configurations, together with their nanoscale resolution, provides additional information about the damage in the different regions/materials of the devices, allowing to correlate device level characteristics with the nanoscale material properties.
Dipòsit Digital de Documents de la UAB
Publication Artículo científico (JournalArticle)

DC characterization and fast small-signal parameter extraction of organic thin film transistors with different geometries

  • Nafria, Montserrat|||0000-0002-9549-2890
  • Crespo-Yepes, A.|||0000-0003-4618-651X
  • Rodriguez, R.|||0000-0002-4565-6703
  • Arnal Rus, August|||0000-0002-3425-1057
  • Ramon, Eloi|||0000-0001-9974-8112
  • Terés Terés, Lluís|||0000-0002-9263-411X
Organic Devices offer low-cost manufacturing and better flexibility, sustainability and solution-processability than their Si-based MOS counterparts, which make them suitable for new applications where those characteristics are an advantage. However, organic device performance is still far from that provided by CMOS technology and many issues are still unclear. In this work, a performance comparison is made between Interdigitated and Corbino geometries of Organic Thin Film Transistors (OTFT), with different areas but fabricated with identical stack materials and techniques. To this end, I-V characteristics and C-V curves of the OTFTs were measured and a Common-Source circuit was proposed and implemented for extracting relevant electrical parameters of the devices, through a standard small signal analysis. The parameter extraction methodology in the frequency domain proposed allows rapid testing of the device/circuit performance of this technology, which for the first time is applied to organic devices. Results show that despite the large voltages, organic transistors exhibit similar channel dimension dependencies to MOS devices and can be also described by the same small signal model.
Dipòsit Digital de Documents de la UAB
Publication Artículo científico (JournalArticle)

Statistical characterization of time-dependent variability defects using the maximum current fluctuation

  • Saraza-Canflanca, Pablo|||0000-0003-2155-8305
  • Martin-Martinez, J.|||0000-0001-5938-5898
  • Castro-Lopez, Rafael|||0000-0002-6247-3124
  • Roca, Elisenda|||0000-0001-6260-6495
  • Rodriguez, R.|||0000-0002-4565-6703
  • Fernandez, Francisco V.|||0000-0001-8682-2280
  • Nafria, Montserrat|||0000-0002-9549-2890
This article presents a new methodology to extract, at a given operation condition, the statistical distribution of the number of active defects that contribute to the observed device time-dependent variability, as well as their amplitude distribution. Unlike traditional approaches based on complex and time-consuming individual analysis of thousands of current traces, the proposed approach uses a simpler trace processing, since only the maximum and minimum values of the drain current during a given time interval are needed. Moreover, this extraction method can also estimate defects causing small current shifts, which can be very complex to identify by traditional means. Experimental data in a wide range of gate voltages, from near-threshold up to nominal operation conditions, are analyzed with the proposed methodology.
Dipòsit Digital de Documents de la UAB
Publication Artículo científico (JournalArticle)

Combined nanoscale KPFM characterization and device simulation for the evaluation of the MOSFET variability related to metal gate workfunction fluctuations

  • Ruiz Flores, Ana|||0000-0002-2475-7353
  • Seoane, Natalia|||0000-0003-0973-461X
  • Claramunt, Sergi|||0000-0002-2888-7825
  • Garcia-Loureiro, Antonio|||0000-0003-0574-1513
  • Porti i Pujal, Marc|||0000-0001-7438-3823
  • Nafria, Montserrat|||0000-0002-9549-2890
In this work, a more realistic approximation based on 2D nanoscale experimental data obtained on a metal layer is presented to investigate the impact of the metal gate polycrystallinity on the MOSFET variability. The nanoscale data (obtained with a Kelvin Probe Force Microscope, KPFM) were introduced in a device simulator to analyze the effect of a TiN metal gate work functions (WF) fluctuations on the MOSFET electrical characteristics. The results demonstrate that the device characteristics are affected not only by the WF fluctuations, but also their spatial distribution, which is specially relevant in very small devices. The effect on these characteristics of the spatial distribution on the gate area of such fluctuations is also evaluated.
Dipòsit Digital de Documents de la UAB
Publication Artículo científico (JournalArticle)

A versatile CMOS transistor array IC for the statistical characterization of time-zero variability, RTN, BTI, and HCI

  • Diaz-Fortuny, Javier|||0000-0002-8186-071X
  • Martin-Martinez, J.|||0000-0001-5938-5898
  • Rodriguez, R.|||0000-0002-4565-6703
  • Castro-Lopez, Rafael|||0000-0002-6247-3124
  • Roca, Elisenda|||0000-0001-6260-6495
  • Aragones, Xavier|||0000-0003-1352-8675
  • Barajas, Enrique|||0000-0002-2072-2268
  • Mateo, Diego|||0000-0001-5996-9092
  • Fernandez, Francisco V.|||0000-0001-8682-2280
  • Nafria, Montserrat|||0000-0002-9549-2890
Statistical characterization of CMOS transistor variability phenomena in modern nanometer technologies is key for accurate end-of-life prediction. This paper presents a novel CMOS transistor array chip to statistically characterize the effects of several critical variability sources, such as time-zero variability (TZV), random telegraph noise (RTN), bias temperature instability (BTI), and hot-carrier injection (HCI). The chip integrates 3136 MOS transistors of both pMOS and nMOS types, with eight different sizes. The implemented architecture provides the chip with a high level of versatility, allowing all required tests and attaining the level of accuracy that the characterization of the above-mentioned variability effects requires. Another very important feature of the array is the capability of performing massively parallel aging testing, thus significantly cutting down the time for statistical characterization. The chip has been fabricated in a 1.2-V, 65-nm CMOS technology with a total chip area of 1800 x 1800 mu m(2).
Dipòsit Digital de Documents de la UAB
Publication Artículo científico (JournalArticle)

Workfunction fluctuations in polycrystalline TiN observed with KPFM and their impact on MOSFETs variability

  • Ruiz Flores, Ana|||0000-0002-2475-7353
  • Seoane, Natalia|||0000-0003-0973-461X
  • Claramunt, Sergi|||0000-0002-2888-7825
  • Garcia-Loureiro, Antonio|||0000-0003-0574-1513
  • Porti i Pujal, Marc|||0000-0001-7438-3823
  • Couso, Carlos|||0000-0003-4757-2439
  • Martin-Martinez, J.|||0000-0001-5938-5898
  • Nafria, Montserrat|||0000-0002-9549-2890
A more realistic approach to evaluate the impact of polycrystalline metal gates on the MOSFET variability is presented. 2D experimental workfunction maps of a polycrystalline TiN layer were obtained by Kelvin Probe Force Microscopy with a nanometer resolution. These data were the input of a device simulator, which allowed us to evaluate the effect of the workfunction fluctuations on MOSFET performance variability. We have demonstrated that in the modelling of TiN workfunction variability not only the different workfunctions of the grains but also the grain boundaries should be included.
Dipòsit Digital de Documents de la UAB
Publication Artículo científico (JournalArticle)

A smart noise- and RTN-removal method for parameter extraction of CMOS aging compact models

  • Diaz-Fortuny, Javier|||0000-0002-8186-071X
  • Martin-Martinez, J.|||0000-0001-5938-5898
  • Rodriguez, R.|||0000-0002-4565-6703
  • Castro-Lopez, Rafael|||0000-0002-6247-3124
  • Roca, Elisenda|||0000-0001-6260-6495
  • Fernandez, Francisco V.|||0000-0001-8682-2280
  • Nafria, Montserrat|||0000-0002-9549-2890
In modern nanometer-scale CMOS technologies, time-zero and time-dependent variability (TDV) effects, the latter coming from aging mechanisms like Bias Temperature Instability (BTI), Hot Carrier Injection (HCI) or Random Telegraph Noise (RTN), have re-emerged as a serious threat affecting the performance of analog and digital integrated circuits. Variability induced by the aging phenomena can lead circuits to a progressive malfunction or failure. In order to understand the effects of the mentioned variability sources, a precise and sound statistical characterization and modeling of these effects should be done. Typically, transistor TDV characterization entails long, and typically prohibitive, testing times, as well as huge amounts of data, which are complex to post-process. In order to face these limitations, this work presents a new method to statistically characterize the emission times and threshold voltage shifts (Delta V-th) related to oxide defects in nanometer CMOS transistors during aging tests. At the same time, the aging testing methodology significantly reduces testing times by parallelizing the stress. The method identifies the V-th drops associated to oxide trap emissions during BTI and HCI aging recovery traces while removing RTN and background noise contributions, to avoid artifacts during data analysis.
Dipòsit Digital de Documents de la UAB
Publication Artículo científico (JournalArticle)

A flexible characterization methodology of RRAM, application to the modeling of the conductivity changes as synaptic weight updates

  • Pedro, Marta|||0000-0003-0317-7373
  • Martin-Martinez, J.|||0000-0001-5938-5898
  • Rodriguez, R.|||0000-0002-4565-6703
  • Bargallo Gonzalez, Mireia|||0000-0001-6792-4556
  • Campabadal, Francesca|||0000-0001-7758-4567
  • Nafria, Montserrat|||0000-0002-9549-2890
In this work, an automatic and flexible measurement setup, which allows a massive electrical characterization of single RRAM devices with pulsed voltages, is presented. The evaluation of the G-V maps under single-pulse test-schemes is introduced as an example of application of the proposed methodology, in particular for neuromorphic engineering, where the fine analog control of the synaptic device conductivity state is required, by inducing small changes in each learning iteration. To describe the obtained data, a time-independent compact model for memristive devices is used. The fitting parameters statistical distributions are further studied.
Dipòsit Digital de Documents de la UAB
Publication Artículo científico (JournalArticle)

An unsupervised and probabilistic approach to Pavlov's dog experiment with OxRAM devices

  • Martin-Martinez, J.|||0000-0001-5938-5898
  • Rodriguez, R.|||0000-0002-4565-6703
  • Nafria, Montserrat|||0000-0002-9549-2890
  • Pedro, Marta|||0000-0003-0317-7373
  • Bargallo Gonzalez, Mireia|||0000-0001-6792-4556
  • Campabadal, Francesca|||0000-0001-7758-4567
In this work, a potential basis for implementing unsupervised associative learning in two or more memristors within neuromorphic architectures is proposed. The experimental demonstration is carried out by means of emulating the Pavlov's dog classical conditioning experiment with two OxRAM devices, in which the dependence of the probability of association on test parameters, such as the pulse amplitude, is studied.
Dipòsit Digital de Documents de la UAB
Publication Artículo científico (JournalArticle)

Statistical threshold voltage shifts caused by BTI and HCI at nominal and accelerated conditions

  • Diaz-Fortuny, Javier|||0000-0002-8186-071X
  • Saraza-Canflanca, Pablo|||0000-0003-2155-8305
  • Rodriguez, R.|||0000-0002-4565-6703
  • Martin-Martinez, J.|||0000-0001-5938-5898
  • Castro-Lopez, Rafael|||0000-0002-6247-3124
  • Roca, Elisenda|||0000-0001-6260-6495
  • Fernandez, Francisco V.|||0000-0001-8682-2280
  • Nafria, Montserrat|||0000-0002-9549-2890
In nowadays deeply scaled CMOS technologies, time-zero and time-dependent variability effects have become important concerns for analog and digital circuit design. For instance, transistor parameter shifts caused by Bias Temperature Instability and Hot-Carrier Injection phenomena can lead to progressive deviations of the circuit performance or even to its catastrophic failure. In this scenario, and to understand the effects of these variability sources, an extensive and accurate device characterization under several test conditions has become an unavoidable step towards trustworthy implementing the stochastic reliability models and simulation tools needed to achieve reliable integrated circuits. In this paper, the statistical distributions of threshold voltage shifts in nanometric CMOS transistors will be studied at nominal and accelerated aging conditions. To this end, a versatile transistor array chip and a flexible measurement setup have been used to reduce the required testing time to attainable values.
Dipòsit Digital de Documents de la UAB
Publication Artículo científico (JournalArticle)

A CAFM and device level study of MIS structures with graphene as interfacial layer for ReRAM applications

  • Claramunt, Sergi|||0000-0002-2888-7825
  • Ruiz Flores, Ana|||0000-0002-2475-7353
  • Wu, Q.
  • Porti i Pujal, Marc|||0000-0001-7438-3823
  • Nafria, Montserrat|||0000-0002-9549-2890
  • Aymerich Humet, Xavier|||0000-0002-5874-6257
Capacitive Metal-Insulator-Semiconductor structures with graphene as interfacial layer between the HfO dielectric and the top electrode have been fabricated and investigated at device level and at the nanoscale with Conductive Atomic Force Microscope. In particular, their electrical properties and variability have been compared to devices without graphene to evaluate their feasibility as ReRAM devices. At device level, we observe that, when graphene is present as an intercalated layer, several resistive switching cycles can be measured, meanwhile the standard structures without graphene do not show resistive switching behavior. Nanoscale analysis showed that the graphene layer prevents the microstructural irreversible damage of the oxide material during a forming process. Therefore, graphene somehow protects the structure during the CF formation. This protection would explain the observation of RS of the devices with intercalated graphene.
Dipòsit Digital de Documents de la UAB
Publication Artículo científico (JournalArticle)

Modeling of the degradation of CMOS inverters under pulsed stress conditions from 'on-the-fly' measurements

  • Crespo-Yepes, A.|||0000-0003-4618-651X
  • Ramos, R.
  • Barajas, Enrique|||0000-0002-2072-2268
  • Aragones, Xavier|||0000-0003-1352-8675
  • Mateo, Diego|||0000-0001-5996-9092
  • Martin-Martinez, J.|||0000-0001-5938-5898
  • Rodriguez, R.|||0000-0002-4565-6703
  • Nafria, Montserrat|||0000-0002-9549-2890
In this work, an 'on-the-fly' measurement technique for the monitoring of CMOS inverters performance degradation is presented. This technique allows the characterization of the circuit degradation simultaneously with the applications of the stress. In our experiments, the inversion voltage (V) shifts measured during the application of pulsed voltage stresses at the input. It is demonstrated that the shifts can be described by a power law that accounts for the stress time and voltage dependences. Moreover, the circuit degradation has been correlated to the NMOS and PMOS degradations. The results show that the degradation of the CMOS inverter can be evaluated from an analytical equation that considers only the shifts of two parameters (threshold voltage V, and mobility µ) of the two transistors in the inverter.
Dipòsit Digital de Documents de la UAB
Publication Artículo científico (JournalArticle)

Unified RTN and BTI statistical compact modeling from a defect-centric perspective

  • Pedreira Rincon, Gerard|||0000-0002-7792-6501
  • Martin-Martinez, J.|||0000-0001-5938-5898
  • Saraza-Canflanca, Pablo|||0000-0003-2155-8305
  • Castro-Lopez, Rafael|||0000-0002-6247-3124
  • Rodriguez, R.|||0000-0002-4565-6703
  • Roca, Elisenda|||0000-0001-6260-6495
  • Fernandez, Francisco V.|||0000-0001-8682-2280
  • Nafria, Montserrat|||0000-0002-9549-2890
In nowadays deeply scaled CMOS technologies, time-dependent variability effects have become important concerns for analog and digital circuit design. Transistor parameter shifts caused by Bias Temperature Instability and Random Telegraph Noise phenomena can lead to deviations of the circuit performance or even to its fatal failure. In this scenario extensive and accurate device characterization under several test conditions has become an unavoidable step towards trustworthy implementing the stochastic reliability models. In this paper, the statistical distributions of threshold voltage shifts in nanometric CMOS transistors will be studied at near threshold, nominal and accelerated aging conditions. Statistical modelling of RTN and BTI combined effects covering the full voltage range is presented. The results of this work suppose a complete modelling approach of BTI and RTN that can be applied in a wide range of voltages for reliability predictions.
Dipòsit Digital de Documents de la UAB
Publication Artículo científico (JournalArticle)

A Smart Measurement System for the Combined Nanoscale and Device Level Characterization of Electron Devices, Implementation Using Ink-Jet Printing Technologies

  • Claramunt, Sergi|||0000-0002-2888-7825
  • Arrese, Javier|||0000-0003-2743-8013
  • Ruiz Flores, Ana|||0000-0002-2475-7353
  • Porti i Pujal, Marc|||0000-0001-7438-3823
  • Cirera, Albert|||0000-0002-2075-1536
  • Nafria, Montserrat|||0000-0002-9549-2890
In this article, the integration into a single measurement system of device level and nanoscale measurement equipment is presented and applied to the electrical characterization of emerging electron devices. This system is a smart solution to simplify the test procedure, since it allows a fast switching between measurement modes (device or nanoscale level), also featuring an enlarged testing capability. Key in the system is a custom-made inkjet-printed circuit board (I-PCB) that connects the device terminals to the proper instrumentation. The flexibility offered by inkjet-printing technologies is a clear advantage, since many kinds of devices can be tested, without the need of expensive hardware modifications. As a particular case of study, the proposed strategy is demonstrated by implementing a system that alternates between standard electrical measurements with a Semiconductor Parameter Analyzer (SPA) and Conductive Atomic Force Microscopy (CAFM) nanoscale measurements on back-gate graphene field-effect transistors.
Dipòsit Digital de Documents de la UAB
Publication Artículo científico (JournalArticle)

Methodology for the simulation of the variability of MOSFETs with polycrystalline high-k dielectrics using CAFM input data

  • Ruiz Flores, Ana|||0000-0002-2475-7353
  • Couso, Carlos|||0000-0003-4757-2439
  • Seoane, Natalia|||0000-0003-0973-461X
  • Porti i Pujal, Marc|||0000-0001-7438-3823
  • Garcia-Loureiro, Antonio|||0000-0003-0574-1513
  • Nafria, Montserrat|||0000-0002-9549-2890
In this work, a simulation methodology, whose inputs are Conductive Atomic Force Microscope (CAFM) experimental data, is proposed to evaluate the impact of nanoscale variability sources related to the polycrystallization of high-k dielectrics (i.e., oxide thickness, tox, and charge density, ρox, fluctuations in the nanometer range) on the Metal-Oxide-Semiconductor Field Effect Transistor (MOSFET) variability. To simulate this variability, a Thickness And Charge MAp Generator (TACMAG) has been developed and used in combination with an in-house-built 3D device simulator (VENDES). From CAFM experimental data (topography and current) obtained on a small area of a given polycrystalline dielectric, the TACMAG generates a high amount of tox and ρox configurations of the gate dielectric, with identical statistical characteristics to those experimentally measured. These dielectrics are then introduced into the device simulator, with which the impact of the tox and ρox fluctuations in the dielectric on the variability of MOSFETs (i.e., threshold voltage) is analyzed. Finally, the impact of different nanoscale parameters, such as the Grain size and Grain Boundaries depth (of polycrystalline dielectrics) on such variability has been evaluated.
Dipòsit Digital de Documents de la UAB
Publication Capítulo o parte de un libro (BookPart)

Circuit reliability prediction, challenges and solutions for the device time-dependent variability characterization roadblock

  • Nafria, Montserrat|||0000-0002-9549-2890
  • Diaz-Fortuny, Javier|||0000-0002-8186-071X
  • Saraza-Canflanca, Pablo|||0000-0003-2155-8305
  • Martin-Martinez, J.|||0000-0001-5938-5898
  • Roca, Elisenda|||0000-0001-6260-6495
  • Castro-Lopez, Rafael|||0000-0002-6247-3124
  • Rodriguez, R.|||0000-0002-4565-6703
  • Martin-Lloret, Pablo
  • Toro-Frias, Antonio|||0000-0002-4722-9377
  • Mateo, Diego|||0000-0001-5996-9092
  • Barajas, Enrique|||0000-0002-2072-2268
  • Aragones, Xavier|||0000-0003-1352-8675
  • Fernandez, Francisco V.|||0000-0001-8682-2280
The characterization of the MOSFET Time-Dependent Variability (TDV) can be a showstopper for reliability-aware circuit design in advanced CMOS nodes. In this work, a complete MOSFET characterization flow is presented, in the context of a physics-based TDV compact model, that addresses the main TDV characterization challenges for accurate circuit reliability prediction at design time. The pillars of this approach are described and illustrated through examples.