Skip to main content

CELULAS SOLARES CON CONTACTOS POSTERIORES BASADAS EN SUBSTRATOS DELGADOS DE SILICIO CRISTALINO

TEC2017-82305-R

•
Funding agency name Agencia Estatal de Investigación
Funding agency acronym AEI
Program Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Call Proyectos I+D+i Retos de Investigación
Call year 2017
State Plan 2017-2020 Plan Estatal de Investigación Científica y Técnica y de Innovación
Beneficiary centre UNIVERSITAT POLITECNICA DE CATALUNYA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 24
Encontrada(s) 1 página(s)

UPCommons. Portal del coneixement obert de la UPC
Publication Artículo científico (JournalArticle)

Textured PDMS films applied to thin crystalline silicon solar cells

  • Rosell, Arnau
  • Martín García, Isidro|||0000-0001-8833-9057
  • Garin Escriva, Moises|||0000-0003-1309-7457
  • López Rodríguez, Gema|||0000-0003-4806-5180
  • Alcubilla González, Ramón|||0000-0003-4827-4513
© 2020 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes,creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., Front surface texturization is a standard procedure used to improve optical properties of photovoltaic devices. In some particular cases, such as when dealing with ultrathin substrates, common texturization techniques can become unpractical or even unfeasible. Texturized polymer films applied on top of such devices may be used as an alternative. In this article, we report on the development of textured polydimethylsiloxane (PDMS) films to be placed on top of planar crystalline silicon solar cells based on thin substrates (=40 µ m). The PDMS polymer is deposited onto a rough surface (conventional random pyramid textured silicon), cured and detached from it. By scanning electron microscope images, we demonstrate that the dilution of PDMS into toluene helps in a better replica of the master surface. Next, we apply the optimized PDMS films on top of dummy samples based on 10, 20, and 40 µm thick crystalline silicon (c-Si) substrates whose reflectance is significantly reduced after placing the PDMS films. Accurate optical simulations indicate that the optical improvement comes from three mechanisms: higher light transmission into the device, lower reflectance at the c-Si surface, and better light trapping properties at the thin c-Si absorber. Experimental verification of the optical improvement with texturized PDMS films is reported based on 40 µ m thick solar cell, where a short-circuit current density gain of 1.7 mA/cm 2 is observed., This work was funded by MINECO from Spanish government under projects TEC2017-82305-R, ENE2016-78933-C4-1-R, ENE2017-87671-C3-2-R. The work was also supported in part by project REFER COMRDI15-1-0036 funded by ACCIÓ and the European Regional Development Fund (FEDER)., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Artículo científico (JournalArticle)

Low-cost high-sensitive suns-Voc measurement instrument to characterize c-Si solar cells

  • Ortega Villasclaras, Pablo Rafael|||0000-0001-6577-614X
  • Piñol, Juan M.
  • Martín García, Isidro|||0000-0001-8833-9057
  • Orpella García, Alberto|||0000-0003-2726-5861
  • Masmitjà Rusiñol, Gerard|||0000-0001-9541-7586
  • López Rodríguez, Gema|||0000-0003-4806-5180
  • Ros Costals, Eloi|||0000-0002-1952-6614
  • Voz Sánchez, Cristóbal|||0000-0002-0320-9606
  • Puigdollers i González, Joaquim|||0000-0002-1834-2565
  • Alcubilla González, Ramón|||0000-0003-4827-4513
© 2020 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes,creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., Measuring open-circuit voltage (Voc) vs. light intensity (Suns) in solar cells permits the access of cell performance without the series resistance effect. This work shows the implementation of a Suns-Voc measurement system which consists of an off-the-shelf photograph flash-lamp, a digital oscilloscope and a specifically designed photodetector board with three silicon photodiodes that covers a light intensity measurement range from 10-5 to 102 suns. The whole system is controlled via USB ports from a personal computer allowing the measurement of cell characteristics (pseudo-dark and pseudo-light current density-voltage curves, as well as the pseudo fill factor and pseudo efficiency) automatically in a very short time., This work was supported in part by the Spanish Government under a FPU grant (FPU13/04381), and projects ENE2016-78933-C4-1-R, ENE2017-87671-C3-2-R and TEC2017-82305-R. The work was also supported in part by the project REFER COMRDI15-1-0036 funded by ACCIÓ and the European Regional Development Fund (FEDER). The authors wish to thank Mr. Miguel Garcia for its help in the mechanical and electrical photodetector interface development., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Artículo científico (JournalArticle)

3D simulations of interdigitated back-contacted crystalline silicon solar cells on thin substrates

  • Jin, Chen
  • Martín García, Isidro|||0000-0001-8833-9057
  • Ortega Villasclaras, Pablo Rafael|||0000-0001-6577-614X
  • Calle Martín, Eric
  • Alcubilla González, Ramón|||0000-0003-4827-4513
© <2018>. This manuscript version is made available under the CC-BY-NC-ND 4.0 license http://creativecommons.org/licenses/by-nc-nd/4.0/, Interdigitated back contact technology is a promising candidate to be applied to thin crystalline silicon solar cells because of its simpler one-side interconnection while allowing a more flexible front surface treatment. This work explores the efficiency potential of IBC c-Si solar cells applied to thin c-Si substrates through 3D device simulations. In particular, we explore the impact of substrate thickness and front surface recombination velocity on cell performance with special attention to the different behavior in carrier collection of two different rear-surface doping structures. Firstly, the model is validated by comparing simulation results to a fabricated device on 280¿µm-thick substrates with stripe-like p+ and n+ diffusions. It is revealed that efficiencies of 16–17% are reachable for substrates on the 10–15¿µm range without changing the technology developed for thick ones. Next, the rear doping structure is modified leading to doped regions just under the metal contacts. This type of structure is expected in solar cells where high-temperature diffusions are replaced by point-like laser doped contacts, which is a feasible alternative to be applied to thin substrates. Simulation results show that diffusion length requirements for those locally-doped structures are more demanding due to the reduction of emitter regions. As a result, very well passivated front and rear surfaces are required to maintain short-circuit current densities to reasonable values. Finally, for both structures open-circuit voltage is kept almost constant with reduced thickness, despite the strong reduction in short-circuit current. Simulations show a reduction of dark saturation current density with substrate thinning due to the redistribution of dark current densities that flow parallel to the device surface., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Artículo científico (JournalArticle)

Direct etching at the nanoscale through nanoparticle-directed capillary condensation

  • Garín, Moisés
  • Khoury, Rasha
  • Martín García, Isidro|||0000-0001-8833-9057
  • Johnson, Erik
We report a method to locally deliver a chemical etchant at the nanoscale in the vapor phase by capillary condensation forming a meniscus at the nanoparticle/substrate interface. The process is simple, scalable and does not require functionalization of the nanoparticles. Furthermore, it does not rely on any specific chemical properties of the materials other than the solution being aqueous and the wettability properties of the surfaces involved, which should enable its application to other material and chemical combinations. In particular, in this work we demonstrate the proposed process by periodically pattering a SiO2 layer using a self-assembled monolayer of polystyrene particles exposed to HF vapors. The patterned SiO2 layer is then used as a mask to etch a pattern of inverted nanopyramids on Si. The silicon nanopatterning has been demonstrated for particles sizes ranging from 800 nm down to 100 nm, providing pyramids with a size down to 50 nm for 100 nm nanoparticles., This work has been financially supported by the following projects: ENE2015-74009-JIN funded by the Spanish Ministry of Economy and Competitiveness (MINECO) and the European Regional Development Fund (ERDF-EU), TEC2017-82305-R (MINECO), the InnoEnergy PhD School Programme and the European Institute of Technology (EIT)., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Artículo científico (JournalArticle)

Impedance spectroscopy interpretation of silica and polystyrene colloidal suspensions

  • Véliz Noboa, Bremnen Marino
  • Orpella García, Alberto|||0000-0003-2726-5861
  • Domínguez Pumar, Manuel|||0000-0001-5439-7953
  • Bermejo Broto, Sandra|||0000-0003-1660-0273
© <2020> Elsevier. This manuscript version is made available under the CC-BY-NC-ND 4.0 license http://creativecommons.org/licenses/by-nc-nd/4.0/, Impedance spectroscopy differences between colloidal 295-nm silica and 300-nm polystyrene nanoparticles in deionized water are analyzed in this work. Using two different two-electrode measurement setups, designed for this application, impedance spectroscopy measurements performed directly in the colloidal suspensions with same nanoparticles size, shape and concentration, are fitted using Randles circuit models. The parameter analysis allows to identify the suspension response, the electrode-suspension interfaces response and nanoparticle double layer response. The first measurement system consists of a two aluminum wire electrodes characterized in a frequency range from 0.1Hz to 100 kHz while the second system was two square stainless steel electrodes characterized from 0.1Hz to 5 MHz. According to the results, polystyrene nanoparticles suspension presents higher conductivity and higher values of capacitance than silica suspension. It is revealed that as the nanoparticle concentration decreases, the suspension conductivity decreases for both colloidal suspensions. On the other hand, the electrode polarization effect contributed with high impedance and capacitance values, but showed a contrary behavior with the variation of the nanoparticles concentration. These differences found mainly arise because of the hydrophilic and hydrophobic nature of the silica and polystyrene nanoparticle surfaces., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Contribución de congreso (ConferenceOutput)

Electron selective contacts based on Al2O3/TiO2/ZnO stacks for crystalline silicon solar cells

  • Zafoschnig, Lisa
  • Ortega Villasclaras, Pablo Rafael|||0000-0001-6577-614X
  • Martín García, Isidro|||0000-0001-8833-9057
  • Masmitjà Rusiñol, Gerard|||0000-0001-9541-7586
  • López Rodríguez, Gema|||0000-0003-4806-5180
  • Alcubilla González, Ramón|||0000-0003-4827-4513
In the last years, our research group has focused on the development of Interdigitated Back Contacted (IBC) solar cells based on transition metal oxides. In particular, a very thin Al2O3/TiO2 stack deposited by ALD has demonstrated excellent results. The point of this work is to try to develop a transparent conductive oxide that could be inserted in between the passivating layers and the metal contact in order to improve rear reflector properties. As a good candidate, we focus on Zinc Oxide (ZnO) deposited from DEZ (Ditehylzinc) and water as gas precursors. A deposition rate of 1.76 A/cycle is found for layers deposited at 125 ºC indicating a self-limited reaction, i.e. atomic layer deposition process. This film has an optical band gap of 3.26 eV demonstrating good optical properties to work as a back reflector. Unfortunately, contact quality with these layers is very poor. In order to investigate the origin of such a poor performance, we measure ZnO workfunction by Scanning Kelvin Probe resulting in 4.85 eV. This value suggests that the developed ZnO films could work better in a hole selective contact. To demonstrate this point, contacts on MoOx layers were fabricated leading to reasonable contact resistance values of 43 mohmscm. Passivation properties of these contacts will be addressed in the future in order to consider their introduction into the final IBC solar cell., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Artículo científico (JournalArticle)

Analysis and impedance modeling of silica and polystyrene nanoparticles in EMIM structures for humidity sensing applications

  • Véliz Noboa, Bremnen Marino
  • Orpella García, Alberto|||0000-0003-2726-5861
  • Domínguez Pumar, Manuel|||0000-0001-5439-7953
  • Bermejo Broto, Sandra|||0000-0003-1660-0273
This work shows the fabrication technology details and a proposed impedance spectroscopy modeling of Electrosprayed-nanoparticles Metal Insulator Metal (EMIM) structures, and their potential as humidity sensors. The impedance measurement of two structures based on 255-nm silica and 295-nm polystyrene nanoparticles under different relative humidity levels (30-90 %RH) and scanning electron microscopy were carried out. A higher capacitance in silica than in polystyrene EMIM structure is attributed to the adsorption of moisture and the diffusion of charges through the Grotthus mechanism onto the nanoparticle surface. The Poole-Frenkel dielectric conductivity in the silica capacitor is interpreted, which increases with decreasing humidity. While the Ohmic dielectric conductivity in PS nanostructure decreases with decreasing humidity. The silica EMIM structure has a good linear capacitance dependence on the humidity of almost 95% and a maximum sensitivity of 6362%, defined as ¿C/C30%, is obtained, making these devices a promising novel nanostructure for humidity sensing applications., This work has been supported by the Spanish Ministry MINECO under projects TEC2017-82305-R, RTI2018-098728-B-C33, by the European Space Agency under project ESA AO/1-8876/17/NL/CRS, and by the SENESCYT-IFTH of the republic of Ecuador under agreement 2016-AR5G8871., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Artículo científico (JournalArticle)

Influence of a gold seed in transparent V2Ox/Ag/V2Ox selective contacts for dopant-free silicon solar cells

  • Nguyen, Hieu Trung
  • Ros Costals, Eloi|||0000-0002-1952-6614
  • Bertomeu Balaguero, Joan
  • Asensi López, José Miguel
  • Andreu Batallé, Jordi
  • Martín García, Isidro|||0000-0001-8833-9057
  • Ortega Villasclaras, Pablo Rafael|||0000-0001-6577-614X
  • Garin Escriva, Moises|||0000-0003-1309-7457
  • Puigdollers i González, Joaquim|||0000-0002-1834-2565
  • Voz Sánchez, Cristóbal|||0000-0002-0320-9606
  • Alcubilla González, Ramón|||0000-0003-4827-4513
  • Tom, Thomas
© 2018 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes,creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., Dielectric/metal/dielectric structures based on vanadium pentoxide with a thin silver interlayer have been optimized to replace traditional transparent electrodes. As would be expected, there is a tradeoff in the metal thickness to achieve high transparency and low sheet resistance simultaneously. It has been demonstrated that an ultra-thin gold seed prevents the tendency of silver to form clusters. This wetting effect reduces the metal thickness needed to form a continuous film, which leads to a higher averaged transmittance and very low sheet resistance. On the other hand, vanadium pentoxide on silicon forms a high-quality hole-selective contact. Thus, these structures can be used as an all-in-one transparent electrode and selective contact for a new kind of heterojunction solar cells. This concept has been proved in a 13.3% efficient solar cell fabricated on n-type silicon wafers. Besides being dopant-free, the complete fabrication route did not require any sputtered transparent electrode., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Artículo científico (JournalArticle)

Application of quasi-steady-state photoconductance technique to lifetime measurements on crystalline germanium substrates

  • Martín García, Isidro|||0000-0001-8833-9057
  • Alcañiz, A.
  • Jiménez Pagán, Alba
  • López Rodríguez, Gema|||0000-0003-4806-5180
  • del Cañizo Nadal, Carlos
  • Datas Medina, Alejandro
© 2020 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes,creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., Similar to other high quality crystalline absorbers, an accurate knowledge of surface passivation of crystalline germanium (c-Ge) substrates is crucial for a straightforward improvement of photovoltaic device performance. For crystalline silicon devices, this information is typically obtained by quasi-steady-state photoconductance (QSS-PC) technique using Sinton WCT-120 tool. In this article, we explore the conditions to adapt this measurement technique to c-Ge substrates. Based on PC-1D simulations, we deduce that a minimum effective lifetime is needed corresponding to an effective diffusion length equal to the substrate thickness. Apart from this, an accurate estimation of the total photogeneration inside the c-Ge sample is also mandatory. This condition implies that the light intensity that impinges onto the sample must be measured with a c-Ge sensor, although the integrated c-Si sensor can be used for high flash intensities. Additionally, the optical factor used to evaluate sample reflectance must be also known, which is determined by measuring robust effective lifetime values under photoconductance decay conditions. Finally, knowledge about carrier mobility in c-Ge is also necessary to translate the measured photoconductance to the corresponding excess carrier density values. Lifetime measurements of passivated c-Ge substrates done by QSS-PC technique are validated by comparing them with the ones obtained by microwave photoconductance technique., This work was partially funded by Ministerio de Ciencia, Innovación y Universidades from Spanish government under projects TEC2017-82305-R and ENE2017-86683-R, and Comunidad de Madrid under project Madrid-PV2 (S2018/EMT-4308). A. Jiménez acknowledges “Programa de Ayudas a la Investigación en Energía y Medio Ambiente 2019” from Fundación Iberdrola., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Artículo científico (JournalArticle)

Observation of photovoltaic effect within locally doped silicon nanojunctions using conductive probe AFM

  • Khoury, R.
  • Alvarez, José
  • Ohashi, T.
  • Martín García, Isidro|||0000-0001-8833-9057
  • Ortega Villasclaras, Pablo Rafael|||0000-0001-6577-614X
  • López Rodríguez, Gema|||0000-0003-4806-5180
  • Jin, Chen
  • Li, J.
  • Rusli, E.
  • Bulkin, P.
  • Johnson, E. V.
© <2020>. This manuscript version is made available under the CC-BY-NC-ND 4.0 license http://creativecommons.org/licenses/by-nc-nd/4.0/, Localized p-doped nanojunctions (200–300 nm in diameter) were formed in n-type crystalline silicon substrates and were characterized using scanning electron microscopy (SEM) and conductive-probe atomic force microscopy (C-AFM). Localized doping was performed by diffusion through sub-micron sized holes in a silicon-oxide mask defined using self-organized polystyrene nanoparticles. After oxide removal, a significant brightness contrast in the SEM top and side view images strongly suggested the successful local doping of these areas. Furthermore, local current-voltage measurements performed by C-AFM revealed an open circuit voltage and a short-circuit current only in the areas defined as nanojunctions. This photovoltaic effect is driven by the laser used to control cantilever deflection in the AFM., We acknowledge the financial support of the InnoEnergy PhD School Program and the European Institute of Technology (EIT). This work was partially funded by the Spanish government under projects TEC2017-82305-R, ENE2016-78933-C4-1-R and ENE2017-87671-C3-2-R, and by the Agence Nationale de la Recherche through the ANR project “APOCALYPSO” (ANR-13- PRGE-0003-01)., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Artículo científico (JournalArticle)

Shedding light on the negative differential resistance effect observed in organic thin-film transistors

  • Ros Costals, Eloi|||0000-0002-1952-6614
  • Reig Canyelles, Marta
  • Voz Sánchez, Cristóbal|||0000-0002-0320-9606
  • Bagdziunas, Gintautas
  • Ortega Villasclaras, Pablo Rafael|||0000-0001-6577-614X
  • Velasco Castrillo, Maria Dolores
  • Puigdollers i González, Joaquim|||0000-0002-1834-2565
This document is the unedited Author’s version of a Submitted Work that was subsequently accepted for publication in ACS Applied Electronic Materials, copyright © American Chemical Society after peer review. To access the final edited and published work see https://pubs.acs.org/doi/full/10.1021/acsaelm.0c00183, Organic semiconductor electronics has the potential to become a solid and industrially feasible technology, with new and stimulating applications such as the flexible and transparent electronic devices. However, organic devices still have some drawbacks that must be solved to assure quality and reliability in complex electronic systems. In this work, we focus our attention to the physical origin involved in the negative differential resistance phenomenon, often observed in the output electrical characteristics of organic thin-film transistors but rarely analyzed., This work was supported by the Spanish Government throughProjects ENE2016-78933-C4-1-R, ENE2017-87671-C3-2-R,and TEC2017-82305-R., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Artículo científico (JournalArticle)

Germanium photovoltaic cells with MoO x hole-selective contacts

  • Alcañiz, A.
  • López Rodríguez, Gema|||0000-0003-4806-5180
  • Martín García, Isidro|||0000-0001-8833-9057
  • Jiménez Pagán, Alba
  • Datas Medina, Alejandro
  • Calle, Eric
  • Ros Costals, Eloi|||0000-0002-1952-6614
  • Gerling Sarabia, Luis Guillermo
  • Voz Sánchez, Cristóbal|||0000-0002-0320-9606
  • del Cañizo Nadal, Carlos
  • Alcubilla González, Ramón|||0000-0003-4827-4513
© <2019> Elsevier. This manuscript version is made available under the CC-BY-NC-ND 4.0 license http://creativecommons.org/licenses/by-nc-nd/4.0/, Very thin, thermally evaporated MoOx (x¿<¿3) layer has been used as transparent hole-selective contact on an n-type Germanium substrate to effectively demonstrate PV conversion capability. The fabricated MoOx/Ge heterojunction PV cell shows a photocurrent density of 44.8¿mA/cm2 under AM1.5G illumination, which is comparable to that of conventional Ge PV cells. However, a low open-circuit voltage of 138¿mV is obtained, which might be explained by the presence of tunnelling mechanisms through the MoOx/Ge interface. To our knowledge, this is the first demonstration of a hole-selective contact made of transition metal oxide on an n-type semiconductor different from c-Si. Thus, this work may have important implications toward the development of new device architectures, such as novel low-cost Ge PV cells with possible applications in multijunction solar cells and thermophotovoltaics., Peer Reviewed
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Textured PDMS films applied to thin crystalline silicon solar cells

  • Rosell, Arnau
  • Martín García, Isidro
  • Garin Escriva, Moises
  • López Rodríguez, Gema
  • Alcubilla González, Ramón
© 2020 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes,creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., Front surface texturization is a standard procedure used to improve optical properties of photovoltaic devices. In some particular cases, such as when dealing with ultrathin substrates, common texturization techniques can become unpractical or even unfeasible. Texturized polymer films applied on top of such devices may be used as an alternative. In this article, we report on the development of textured polydimethylsiloxane (PDMS) films to be placed on top of planar crystalline silicon solar cells based on thin substrates (=40 µ m). The PDMS polymer is deposited onto a rough surface (conventional random pyramid textured silicon), cured and detached from it. By scanning electron microscope images, we demonstrate that the dilution of PDMS into toluene helps in a better replica of the master surface. Next, we apply the optimized PDMS films on top of dummy samples based on 10, 20, and 40 µm thick crystalline silicon (c-Si) substrates whose reflectance is significantly reduced after placing the PDMS films. Accurate optical simulations indicate that the optical improvement comes from three mechanisms: higher light transmission into the device, lower reflectance at the c-Si surface, and better light trapping properties at the thin c-Si absorber. Experimental verification of the optical improvement with texturized PDMS films is reported based on 40 µ m thick solar cell, where a short-circuit current density gain of 1.7 mA/cm 2 is observed., This work was funded by MINECO from Spanish government under projects TEC2017-82305-R, ENE2016-78933-C4-1-R, ENE2017-87671-C3-2-R. The work was also supported in part by project REFER COMRDI15-1-0036 funded by ACCIÓ and the European Regional Development Fund (FEDER)., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publication Contribución de congreso (ConferenceOutput)

Electron selective contacts based on Al2O3/TiO2/ZnO stacks for crystalline silicon solar cells

  • Zafoschnig, Lisa
  • Ortega Villasclaras, Pablo Rafael
  • Martín García, Isidro
  • Masmitjà Rusiñol, Gerard
  • López Rodríguez, Gema
  • Alcubilla González, Ramón
In the last years, our research group has focused on the development of Interdigitated Back Contacted (IBC) solar cells based on transition metal oxides. In particular, a very thin Al2O3/TiO2 stack deposited by ALD has demonstrated excellent results. The point of this work is to try to develop a transparent conductive oxide that could be inserted in between the passivating layers and the metal contact in order to improve rear reflector properties. As a good candidate, we focus on Zinc Oxide (ZnO) deposited from DEZ (Ditehylzinc) and water as gas precursors. A deposition rate of 1.76 A/cycle is found for layers deposited at 125 ºC indicating a self-limited reaction, i.e. atomic layer deposition process. This film has an optical band gap of 3.26 eV demonstrating good optical properties to work as a back reflector. Unfortunately, contact quality with these layers is very poor. In order to investigate the origin of such a poor performance, we measure ZnO workfunction by Scanning Kelvin Probe resulting in 4.85 eV. This value suggests that the developed ZnO films could work better in a hole selective contact. To demonstrate this point, contacts on MoOx layers were fabricated leading to reasonable contact resistance values of 43 mohmscm. Passivation properties of these contacts will be addressed in the future in order to consider their introduction into the final IBC solar cell., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Application of quasi-steady-state photoconductance technique to lifetime measurements on crystalline germanium substrates

  • Martín García, Isidro
  • Alcañiz, A.
  • Jiménez Pagán, Alba
  • López Rodríguez, Gema
  • del Cañizo Nadal, Carlos
  • Datas Medina, Alejandro
© 2020 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes,creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., Similar to other high quality crystalline absorbers, an accurate knowledge of surface passivation of crystalline germanium (c-Ge) substrates is crucial for a straightforward improvement of photovoltaic device performance. For crystalline silicon devices, this information is typically obtained by quasi-steady-state photoconductance (QSS-PC) technique using Sinton WCT-120 tool. In this article, we explore the conditions to adapt this measurement technique to c-Ge substrates. Based on PC-1D simulations, we deduce that a minimum effective lifetime is needed corresponding to an effective diffusion length equal to the substrate thickness. Apart from this, an accurate estimation of the total photogeneration inside the c-Ge sample is also mandatory. This condition implies that the light intensity that impinges onto the sample must be measured with a c-Ge sensor, although the integrated c-Si sensor can be used for high flash intensities. Additionally, the optical factor used to evaluate sample reflectance must be also known, which is determined by measuring robust effective lifetime values under photoconductance decay conditions. Finally, knowledge about carrier mobility in c-Ge is also necessary to translate the measured photoconductance to the corresponding excess carrier density values. Lifetime measurements of passivated c-Ge substrates done by QSS-PC technique are validated by comparing them with the ones obtained by microwave photoconductance technique., This work was partially funded by Ministerio de Ciencia, Innovación y Universidades from Spanish government under projects TEC2017-82305-R and ENE2017-86683-R, and Comunidad de Madrid under project Madrid-PV2 (S2018/EMT-4308). A. Jiménez acknowledges “Programa de Ayudas a la Investigación en Energía y Medio Ambiente 2019” from Fundación Iberdrola., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Direct etching at the nanoscale through nanoparticle-directed capillary condensation

  • Garín, Moisés
  • Khoury, Rasha
  • Martín García, Isidro
  • Johnson, Erik
We report a method to locally deliver a chemical etchant at the nanoscale in the vapor phase by capillary condensation forming a meniscus at the nanoparticle/substrate interface. The process is simple, scalable and does not require functionalization of the nanoparticles. Furthermore, it does not rely on any specific chemical properties of the materials other than the solution being aqueous and the wettability properties of the surfaces involved, which should enable its application to other material and chemical combinations. In particular, in this work we demonstrate the proposed process by periodically pattering a SiO2 layer using a self-assembled monolayer of polystyrene particles exposed to HF vapors. The patterned SiO2 layer is then used as a mask to etch a pattern of inverted nanopyramids on Si. The silicon nanopatterning has been demonstrated for particles sizes ranging from 800 nm down to 100 nm, providing pyramids with a size down to 50 nm for 100 nm nanoparticles., This work has been financially supported by the following projects: ENE2015-74009-JIN funded by the Spanish Ministry of Economy and Competitiveness (MINECO) and the European Regional Development Fund (ERDF-EU), TEC2017-82305-R (MINECO), the InnoEnergy PhD School Programme and the European Institute of Technology (EIT)., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Impedance spectroscopy interpretation of silica and polystyrene colloidal suspensions

  • Véliz Noboa, Bremnen Marino
  • Orpella García, Alberto
  • Domínguez Pumar, Manuel
  • Bermejo Broto, Sandra
© <2020> Elsevier. This manuscript version is made available under the CC-BY-NC-ND 4.0 license http://creativecommons.org/licenses/by-nc-nd/4.0/, Impedance spectroscopy differences between colloidal 295-nm silica and 300-nm polystyrene nanoparticles in deionized water are analyzed in this work. Using two different two-electrode measurement setups, designed for this application, impedance spectroscopy measurements performed directly in the colloidal suspensions with same nanoparticles size, shape and concentration, are fitted using Randles circuit models. The parameter analysis allows to identify the suspension response, the electrode-suspension interfaces response and nanoparticle double layer response. The first measurement system consists of a two aluminum wire electrodes characterized in a frequency range from 0.1Hz to 100 kHz while the second system was two square stainless steel electrodes characterized from 0.1Hz to 5 MHz. According to the results, polystyrene nanoparticles suspension presents higher conductivity and higher values of capacitance than silica suspension. It is revealed that as the nanoparticle concentration decreases, the suspension conductivity decreases for both colloidal suspensions. On the other hand, the electrode polarization effect contributed with high impedance and capacitance values, but showed a contrary behavior with the variation of the nanoparticles concentration. These differences found mainly arise because of the hydrophilic and hydrophobic nature of the silica and polystyrene nanoparticle surfaces., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Influence of a gold seed in transparent V2Ox/Ag/V2Ox selective contacts for dopant-free silicon solar cells

  • Nguyen, Hieu Trung
  • Ros Costals, Eloi
  • Bertomeu Balaguero, Joan
  • Asensi López, José Miguel
  • Andreu Batallé, Jordi
  • Martín García, Isidro
  • Ortega Villasclaras, Pablo Rafael
  • Garin Escriva, Moises
  • Puigdollers i González, Joaquim
  • Voz Sánchez, Cristóbal
  • Alcubilla González, Ramón
  • Tom, Thomas
© 2018 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes,creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., Dielectric/metal/dielectric structures based on vanadium pentoxide with a thin silver interlayer have been optimized to replace traditional transparent electrodes. As would be expected, there is a tradeoff in the metal thickness to achieve high transparency and low sheet resistance simultaneously. It has been demonstrated that an ultra-thin gold seed prevents the tendency of silver to form clusters. This wetting effect reduces the metal thickness needed to form a continuous film, which leads to a higher averaged transmittance and very low sheet resistance. On the other hand, vanadium pentoxide on silicon forms a high-quality hole-selective contact. Thus, these structures can be used as an all-in-one transparent electrode and selective contact for a new kind of heterojunction solar cells. This concept has been proved in a 13.3% efficient solar cell fabricated on n-type silicon wafers. Besides being dopant-free, the complete fabrication route did not require any sputtered transparent electrode., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

3D simulations of interdigitated back-contacted crystalline silicon solar cells on thin substrates

  • Jin, Chen
  • Martín García, Isidro
  • Ortega Villasclaras, Pablo Rafael
  • Calle Martín, Eric
  • Alcubilla González, Ramón
© <2018>. This manuscript version is made available under the CC-BY-NC-ND 4.0 license http://creativecommons.org/licenses/by-nc-nd/4.0/, Interdigitated back contact technology is a promising candidate to be applied to thin crystalline silicon solar cells because of its simpler one-side interconnection while allowing a more flexible front surface treatment. This work explores the efficiency potential of IBC c-Si solar cells applied to thin c-Si substrates through 3D device simulations. In particular, we explore the impact of substrate thickness and front surface recombination velocity on cell performance with special attention to the different behavior in carrier collection of two different rear-surface doping structures. Firstly, the model is validated by comparing simulation results to a fabricated device on 280¿µm-thick substrates with stripe-like p+ and n+ diffusions. It is revealed that efficiencies of 16–17% are reachable for substrates on the 10–15¿µm range without changing the technology developed for thick ones. Next, the rear doping structure is modified leading to doped regions just under the metal contacts. This type of structure is expected in solar cells where high-temperature diffusions are replaced by point-like laser doped contacts, which is a feasible alternative to be applied to thin substrates. Simulation results show that diffusion length requirements for those locally-doped structures are more demanding due to the reduction of emitter regions. As a result, very well passivated front and rear surfaces are required to maintain short-circuit current densities to reasonable values. Finally, for both structures open-circuit voltage is kept almost constant with reduced thickness, despite the strong reduction in short-circuit current. Simulations show a reduction of dark saturation current density with substrate thinning due to the redistribution of dark current densities that flow parallel to the device surface., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Shedding light on the negative differential resistance effect observed in organic thin-film transistors

  • Ros Costals, Eloi
  • Reig Canyelles, Marta
  • Voz Sánchez, Cristóbal
  • Bagdziunas, Gintautas
  • Ortega Villasclaras, Pablo Rafael
  • Velasco Castrillo, Maria Dolores
  • Puigdollers i González, Joaquim
This document is the unedited Author’s version of a Submitted Work that was subsequently accepted for publication in ACS Applied Electronic Materials, copyright © American Chemical Society after peer review. To access the final edited and published work see https://pubs.acs.org/doi/full/10.1021/acsaelm.0c00183, Organic semiconductor electronics has the potential to become a solid and industrially feasible technology, with new and stimulating applications such as the flexible and transparent electronic devices. However, organic devices still have some drawbacks that must be solved to assure quality and reliability in complex electronic systems. In this work, we focus our attention to the physical origin involved in the negative differential resistance phenomenon, often observed in the output electrical characteristics of organic thin-film transistors but rarely analyzed., This work was supported by the Spanish Government throughProjects ENE2016-78933-C4-1-R, ENE2017-87671-C3-2-R,and TEC2017-82305-R., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Low-cost high-sensitive suns-Voc measurement instrument to characterize c-Si solar cells

  • Ortega Villasclaras, Pablo Rafael
  • Piñol, Juan M.
  • Martín García, Isidro
  • Orpella García, Alberto
  • Masmitjà Rusiñol, Gerard
  • López Rodríguez, Gema
  • Ros Costals, Eloi
  • Voz Sánchez, Cristóbal
  • Puigdollers i González, Joaquim
  • Alcubilla González, Ramón
© 2020 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes,creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., Measuring open-circuit voltage (Voc) vs. light intensity (Suns) in solar cells permits the access of cell performance without the series resistance effect. This work shows the implementation of a Suns-Voc measurement system which consists of an off-the-shelf photograph flash-lamp, a digital oscilloscope and a specifically designed photodetector board with three silicon photodiodes that covers a light intensity measurement range from 10-5 to 102 suns. The whole system is controlled via USB ports from a personal computer allowing the measurement of cell characteristics (pseudo-dark and pseudo-light current density-voltage curves, as well as the pseudo fill factor and pseudo efficiency) automatically in a very short time., This work was supported in part by the Spanish Government under a FPU grant (FPU13/04381), and projects ENE2016-78933-C4-1-R, ENE2017-87671-C3-2-R and TEC2017-82305-R. The work was also supported in part by the project REFER COMRDI15-1-0036 funded by ACCIÓ and the European Regional Development Fund (FEDER). The authors wish to thank Mr. Miguel Garcia for its help in the mechanical and electrical photodetector interface development., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Observation of photovoltaic effect within locally doped silicon nanojunctions using conductive probe AFM

  • Khoury, R.
  • Alvarez, José
  • Ohashi, T.
  • Martín García, Isidro
  • Ortega Villasclaras, Pablo Rafael
  • López Rodríguez, Gema
  • Jin, Chen
  • Li, J.
  • Rusli, E.
  • Bulkin, P.
  • Johnson, E. V.
© <2020>. This manuscript version is made available under the CC-BY-NC-ND 4.0 license http://creativecommons.org/licenses/by-nc-nd/4.0/, Localized p-doped nanojunctions (200–300 nm in diameter) were formed in n-type crystalline silicon substrates and were characterized using scanning electron microscopy (SEM) and conductive-probe atomic force microscopy (C-AFM). Localized doping was performed by diffusion through sub-micron sized holes in a silicon-oxide mask defined using self-organized polystyrene nanoparticles. After oxide removal, a significant brightness contrast in the SEM top and side view images strongly suggested the successful local doping of these areas. Furthermore, local current-voltage measurements performed by C-AFM revealed an open circuit voltage and a short-circuit current only in the areas defined as nanojunctions. This photovoltaic effect is driven by the laser used to control cantilever deflection in the AFM., We acknowledge the financial support of the InnoEnergy PhD School Program and the European Institute of Technology (EIT). This work was partially funded by the Spanish government under projects TEC2017-82305-R, ENE2016-78933-C4-1-R and ENE2017-87671-C3-2-R, and by the Agence Nationale de la Recherche through the ANR project “APOCALYPSO” (ANR-13- PRGE-0003-01)., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Analysis and impedance modeling of silica and polystyrene nanoparticles in EMIM structures for humidity sensing applications

  • Véliz Noboa, Bremnen Marino
  • Orpella García, Alberto
  • Domínguez Pumar, Manuel
  • Bermejo Broto, Sandra
This work shows the fabrication technology details and a proposed impedance spectroscopy modeling of Electrosprayed-nanoparticles Metal Insulator Metal (EMIM) structures, and their potential as humidity sensors. The impedance measurement of two structures based on 255-nm silica and 295-nm polystyrene nanoparticles under different relative humidity levels (30-90 %RH) and scanning electron microscopy were carried out. A higher capacitance in silica than in polystyrene EMIM structure is attributed to the adsorption of moisture and the diffusion of charges through the Grotthus mechanism onto the nanoparticle surface. The Poole-Frenkel dielectric conductivity in the silica capacitor is interpreted, which increases with decreasing humidity. While the Ohmic dielectric conductivity in PS nanostructure decreases with decreasing humidity. The silica EMIM structure has a good linear capacitance dependence on the humidity of almost 95% and a maximum sensitivity of 6362%, defined as ¿C/C30%, is obtained, making these devices a promising novel nanostructure for humidity sensing applications., This work has been supported by the Spanish Ministry MINECO under projects TEC2017-82305-R, RTI2018-098728-B-C33, by the European Space Agency under project ESA AO/1-8876/17/NL/CRS, and by the SENESCYT-IFTH of the republic of Ecuador under agreement 2016-AR5G8871., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Germanium photovoltaic cells with MoO x hole-selective contacts

  • Alcañiz, A.
  • López Rodríguez, Gema
  • Martín García, Isidro
  • Jiménez Pagán, Alba
  • Datas Medina, Alejandro
  • Calle, Eric
  • Ros Costals, Eloi
  • Gerling Sarabia, Luis Guillermo
  • Voz Sánchez, Cristóbal
  • del Cañizo Nadal, Carlos
  • Alcubilla González, Ramón
© <2019> Elsevier. This manuscript version is made available under the CC-BY-NC-ND 4.0 license http://creativecommons.org/licenses/by-nc-nd/4.0/, Very thin, thermally evaporated MoOx (x¿<¿3) layer has been used as transparent hole-selective contact on an n-type Germanium substrate to effectively demonstrate PV conversion capability. The fabricated MoOx/Ge heterojunction PV cell shows a photocurrent density of 44.8¿mA/cm2 under AM1.5G illumination, which is comparable to that of conventional Ge PV cells. However, a low open-circuit voltage of 138¿mV is obtained, which might be explained by the presence of tunnelling mechanisms through the MoOx/Ge interface. To our knowledge, this is the first demonstration of a hole-selective contact made of transition metal oxide on an n-type semiconductor different from c-Si. Thus, this work may have important implications toward the development of new device architectures, such as novel low-cost Ge PV cells with possible applications in multijunction solar cells and thermophotovoltaics., Peer Reviewed, Postprint (author's final draft)