Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 24
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Optical diagnostics of gold plasmas produced by infrared laser ablation

  • Oujja, Mohamed
  • Camacho, J.J.
  • Sanz, Mikel
  • Castillejo, Marta
  • de Nalda, R.
10 pags., 8 figs., 1 tab., Laser plasmas produced by ablation of a gold target in a vacuum are spatially and temporally characterized by optical emission spectroscopy. A Nd:YAG laser (1064 nm, pulse width 15 ns and fluences of 5.8 and 11 J/cm) is used to ablate the Au target. Au, Au and Auspecies were studied both as a function of the location from the target surface and of the time delay from the laser pulse arrival. Plasma temperature, electron density and average velocities were measured from the spatiotemporal analysis. The results show a faster decay of the continuum emission, Au and Au species than in the case of neutral Au atoms. Higher velocities and a narrower temporal distribution of Au ions are observed when compared to Au atoms. Electron temperature was evaluated from the comparison of Au atomic-Boltzmann local thermodynamic equilibrium spectra with experimental ones at various delay times from the laser pulse incidence. Electron densities and electron temperatures approximately decrease from 2.3 to 1.1 × 10 cm and from 1.6 to 0.4 eV, respectively, as the delay time increases along the first 2 µs of plasma evolution., This research was supported by the Spanish State Research Agency (AEI) and the European Regional Development (FEDER) through Projects CTQ2016-75880-P-AEI/FEDER, PID2019-104124RB-I00/AEI/10.13039/501100011033 and PID2019-106125GB-I00/AEI/10.13039/501100011033; the European H2020 IPERION HS Project (Integrated Platform for the European Research Infrastructure ON Heritage Science) (GA 871034, WP5); TOP Heritage-CM (S2018/NMT-4372) project from the Community of Madrid and with the support of Plataforma Temática Interdisciplinar of CSIC “Patrimonio Abierto: Investigación y Sociedad” (PTI-PAIS). M. O. thanks CSIC for contract.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Multiphoton excitation fluorescence microscopy and spectroscopic multianalytical approach for characterization of historical glass grisailles

  • Oujja, Mohamed
  • Agua Martínez, Fernando
  • Morales-Martín, D.
  • García Heras, Manuel
  • Villegas Broncano, María Ángeles
  • Castillejo, Marta
12 pags., 5 figs., 4 tabs., The preservation of the integrity of artworks and cultural heritage items during characterization and conser-vation operations is of high priority, therefore, the application of non-invasive techniques is commonly suggested and recommended. Nonlinear optical microscopies (NLOM), based on the use of tightly focused pulsed femto-second lasers, are emerging techniques for structural and chemical analysis of heritage objects with micrometric lateral and axial resolution. The results obtained with a set of optical and spectroscopic techniques for the chemical and physical characterization of grisaille paint layers on historical stained glasses, from different chronologies and provenance in Spain, are presented in this work. Optical behaviour and chemical composition were investigated by NLOM, using a laboratory set-up in the modality of Multi-Photon Excitation Fluorescence (MPEF), and by a multi-analytical combination of Field Emission Scanning Electron Microscopy-Energy Dispersive X-ray Spectrometry (FESEM-EDS), Laser Induced Breakdown Spectrosocopy (LIBS) and Laser Induced Fluorescence (LIF). Thicknesses values of the historical grisaille paint layers measured with MPEF were compared with those retrieved through FESEM, showing significant consistency and agreement. Under proper conditions, analysis via MPEF microscopy avoids the photochemical and physical damage to the examined materials, thus ensuring their preservation. This approach paves the way for future in-situ, non-invasive strati-graphic investigations on cultural heritage objects., This research has been funded by the Spanish State Research Agency (AEI) through projects PID2019-104124RB-I00/AEI/10.13039/ 501100011033 and PID2019-104220RB-I00/AEI/10.13039/ 501100011033, by project TOP Heritage-CM (S2018/NMT-4372) from Community of Madrid, by the H2020 European project IPERION HS (Integrated Platform for the European Research Infrastructure ON Her-itage Science, GA 871034) and supported by CSIC Interdisciplinary Platform “Open Heritage: Research and Society” (PTI-PAIS). M.O. thanks CSIC for a contract. Finally, the authors acknowledge profes-sional support from the TechnoHeritage Network of Science and Tech-nology for the Conservation of Cultural Heritage., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Nonlinear optical microscopy for artworks physics

  • Dal Fovo, A.
  • Castillejo, Marta
  • Fontana, Raffaella
46 pags., 22 figs., Nonlinear optical microscopies (NLOMs) are innovative techniques recently introduced in the field of cultural heritage for the non-invasive in-depth analysis of artworks. In this review, we report on the state-of-the-art of NLOMs on different artistic materials, i.e., varnish, glue, paint, wood, parchment, and metal, and we evaluate the potential and capabilities of NLOMs in comparison with other more established linear optical techniques. We also discuss the latest studies defining suitable measurement conditions and instrumental requirements for the safe and in situ application of NLOMs on real cases., This research has been funded by Regione Toscana (POR FSE 2014-2020, “Giovanisì”, Intervention Program “CNR4C”, CUP B15J19001040004), by the Spanish State Research Agency (AEI) through project PID2019-104124RB-I00/ AEI /1.0.13039/501100011033, by the TOP Heritage-CM (S2018/NMT-4372) program, by the H2020 European project IPERION HS (Integrated Platform for the European Research Infrastructure ON Heritage Science, GA 871034) and is supported by CSIC Interdisciplinary Platform “Open Heritage: Research and Society” (PTI-PAIS)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Characterization of medieval-like glass alteration layers by laser spectroscopy and nonlinear optical microscopy

  • Oujja, Mohamed
  • Palomar Sanz, Teresa
  • Martínez-Weinbaum, Marina
  • Martínez-Ramírez, S.
  • Castillejo, Marta
22 pags., 7 figs., 3 tabs., Historical glass-based objects undergo, since the time of their manufacture, different degradation phenomena that are related to their composition and to the environment to which they were exposed. Three-dimensional (3D) structural and chemical characterization of the degradation layers is important to select the most adequate conservation strategies for glass objects. Optical microscopy (OM) is the most frequently used non-destructive method to examine the surface of historical glasses; however, the 3D structural assessment of alteration layers requires applying the destructive modality of this technique to conduct a cross-sectional study. In this work, a different approach for structural and compositional characterization of alteration layers on model medieval-like glasses is presented, based on the combination of the laser spectroscopies of laser-induced breakdown spectroscopy (LIBS), laser-induced fluorescence (LIF) and FT-Raman, and the emerging, cutting edge technique of nonlinear optical microscopy (NLOM) in the modality of multiphoton excitation fluorescence (MPEF). The results obtained through this multi-analytical photonic approach were compared with those retrieved by examination of the surface and cross sections of the samples by OM and scanning electron microscopy–energy-dispersive X-ray spectroscopy (SEM–EDS). While the combination of LIBS, LIF and FT-Raman served to assess the composition of the various alteration layers, the use of MPEF microscopy allowed the non-destructive determination of the thicknesses of these layers, showing for both thickness and composition a good agreement with the OM and SEM–EDS results. Thus, the proposed approach, which avoids sample preparation, illustrates the capability of non-destructive, or micro-destructive in the case of LIBS, laser spectroscopies and microscopies for the in situ study of glass objects of historic or/and artistic value., This research has been funded by the Spanish State Research Agency (AEI) through projects PID2019-104124RB-I00/AEI/1013039/501100011033, the CSIC General Foundation (ComFuturo Programme), by project TOP Heritage-CM (S2018/NMT-4372) from Community of Madrid, by the H2020 European project IPERION HS (Integrated Platform for the European Research Infrastructure ON Heritage Science, GA 871034). Support by CSIC Interdisciplinary Platform “Open Heritage: Research and Society” (PTI-PAIS) is acknowledged. M.O. thanks CSIC for a contract. Open Access funding provided thanks to the CRUE-CSIC agreement with Springer Nature, Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Emission characteristics and dynamics of neutral, ionic and molecular species in a laser produced CaF2 plasma

  • Oujja, Mohamed
  • Camacho, J.J.
  • Paradela, D.
  • Castillejo, Marta
  • de Nalda, R.
15 pags., 12 figs., The emission characteristics of a laser-ablated calcium fluoride CaF plasma have been investigated using time and space optical emission spectroscopy. The plasma-plume was produced by focusing 266 nm, 15 ns pulses from a Nd: YAG laser on a calcium fluoride crystal substrate placed in a vacuum chamber. The emission observed in the plasma region is due to electronic relaxation of excited neutral Ca and F, ionic fragments Ca, Ca and F and molecular features of CaF (AΠ- XΣ, BΣ- XΣ and CΠ- XΣ) band systems. Plasma species were analyzed both as a function of the delay from the laser pulse incidence and location from the target surface. Spectroscopic diagnostics were employed to estimate time-resolved electron densities, electron temperatures and velocity expansion of different species. The results show a faster decay of the continuum emission, ionic F, Ca, Ca, F species than in the case of neutral Ca atoms and molecular species of CaF. Different excitation temperatures were measured by comparing Ca and F atomic/ionic Saha-local thermodynamic equilibrium (LTE) spectra with experimental ones at various delay times after the ablation event. Vibrational temperatures of CaF were assessed from the temporal analysis of the AΠ - XΣ Δv = 0 band sequence molecular emission. We observed a non-equilibrium plasma although the plasma is found to maintain partial LTE., This research was supported by the Spanish State Research Agency (AEI) and the European Regional Development (FEDER) through Projects PID2019-104124RB-I00/AEI/10.13039/501100011033 and PID2019-106125GB-I00/AEI/10.13039/501100011033; the European H2020 IPERION HS Project (Integrated Platform for the European Research Infrastructure ON Heritage Science (GA 871034, WP5)); TOP Heritage-CM (S2018/NMT-4372) project from the Community of Madrid and with the support of Plataforma Temática Interdisciplinar of CSIC “Patrimonio Abierto: Investigación y Sociedad” (PTI-PAIS).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Spectroscopic and Microscopic Characterization of Flashed Glasses from Stained Glass Windows

  • Palomar Sanz, Teresa
  • Martínez-Weinbaum, Marina
  • Aparicio, Mario
  • Maestro-Guijarro, Laura
  • Castillejo, Marta
  • Oujja, Mohamed
18 pags., 6 figs., 3 tabs. -- This article belongs to the Special Issue Interdisciplinary Researches for Cultural Heritage Conservation, Flashed glasses are composed of a base glass and a thin colored layer and have been used since medieval times in stained glass windows. Their study can be challenging because of their complex composition and multilayer structure. In the present work, a set of optical and spectroscopic techniques have been used for the characterization of a representative set of flashed glasses commonly used in the manufacture of stained glass windows. The structural and chemical composition of the pieces were investigated by optical microscopy, field emission scanning electron mi-croscopy‐energy dispersive X‐ray spectrometry (FESEM‐EDS), UV‐Vis‐IR spectroscopy, laser‐in-duced breakdown spectroscopy (LIBS), and laser‐induced fluorescence (LIF). Optical microscopy and FESEM‐EDS allowed the determination of the thicknesses of the colored layers, while LIBS, EDS, UV‐Vis‐IR, and LIF spectroscopies served for elemental, molecular, and chromophores characterization of the base glasses and colored layers. Results obtained using the micro‐invasive LIBS technique were compared with those retrieved by the cross‐sectional technique FESEM‐EDS, which requires sample taking, and showed significant consistency and agreement. In addition, LIBS results revealed the presence of additional elements in the composition of flashed glasses that could not be detected by FESEM‐EDS. The combination of UV‐Vis‐IR and LIF results allowed precise chemical identification of chromophores responsible for the flashed glass coloration., This research has been funded by the Spanish State Research Agency (AEI) through project PID2019-104124RB-I00/AEI/10.13039/501100011033, the Fundación General CSIC (ComFuturo Programme), by project TOP Heritage-CM (S2018/NMT-4372) from Community of Madrid, and by the H2020 European project IPERION HS (Integrated Platform for the European Research Infrastructure ON Heritage Science, GA 871034).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Comparison of the Use of Traditional Solvents and Nanosecond 213 nm Nd:YAG Laser in Thinning Naturally Aged Varnish on a Contemporary Oil Easel Painting

  • Martínez-Weinbaum, Marina
  • Lozano-Carbó, Miriam
  • Maestro-Guijarro, Laura
  • Carmona-Quiroga, Paula
  • Oujja, Mohamed
  • Castillejo, Marta
11 pags., 7 figs., 2 tabs. -- This article belongs to the Special Issue Cleaning Strategies for Cultural Heritage, The removal of aged varnish on artistic paintings is a delicate intervention and the use of UV laser for this purpose is of special relevance. In particular, the use of nanosecond-pulsed lasers operating at 213 nm has been noted to produce good results in mock-up samples, but it has not been tested in real artworks. In this paper, we report on the application of this procedure for the first time on a contemporary oil easel painting with naturally aged varnish. The obtained results were compared with those achieved using traditional solvents, specifically a mixture of ligroin:acetone. Additionally, hot water was used to remove surface dirt. The performance of the different cleaning procedures was assessed with a range of techniques, including low-power microscopy, UV lamp illumination, laser-induced fluorescence (LIF), and laser-induced breakdown spectroscopy (LIBS). Of the tested treatments, the best performance is obtained by nanosecond laser irradiation at 213 nm using an adequate laser fluence (typically 0.14 J/cm2) that allows controlled and efficient removal of the outermost aged varnish layer without affecting the underlying non-aged varnish and paint layers., This research was funded by the Spanish State Research Agency (AEI) through the project SCOCHLAS (Study and Conservation of Cultural Heritage with Lasers, PID2019-104124RB-I00/AEI/1013039/501100011033), by the Community of Madrid through the project Top Heritage-CM (Tecnologías en Ciencias del Patrimonio, S2018/NMT_4372), and by the H2020 project IPERION HS (Integrated Platform for the European Research Infrastructure ON Heritage Science, GA 871034). L. Maestro-Guijarro’s participation was financed by a Youth Guarantee contract (CAM20_IQFR_AI_06) from the Community of Madrid., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Laser-based techniques for the non-invasive characterisation of grisaille paints on stained-glass windows

  • Machado, Carla
  • Oujja, Mohamed
  • Cerqueira Alves, Luis
  • Martínez-Weinbaum, Marina
  • Maestro-Guijarro, Laura
  • Carmona-Quiroga, Paula
  • Castillejo, Marta
  • Vilarigues, Márcia
  • Palomar Sanz, Teresa
Grisaille was the first paint applied on stained-glass panels, used in Europe since the twelfth century. Historical written sources described the use of iron and copper together with a high lead-silica base glass in the grisailles production. This project aims to study the evolution of the grisaille paint composition throughout time and the changes in the raw materials used in their production using non-destructive and non-invasive techniques. To achieve this objective, 23 grisaille samples dated from the 13th to the twentieth centuries from nine different countries (Portugal, Poland, United Kingdom, Sweden, Norway, Belgium, Low Countries, Germany, and France) were studied by means of micro particle-induced X-ray emission (μ-PIXE), micro energy dispersive X-ray fluorescence (μ-EDXRF), laser-induced breakdown spectroscopy (LIBS), laser-induced fluorescence (LIF), non-linear optical microscopy (NLOM) in the modality of multiphoton excitation fluorescence (MPEF) and optical microscopy (OM). The results showed that it was possible to identify compositional differences and patterns throughout the samples when compared with literature results. The preference for using copper in central and south-central European countries and the addition of new compounds (CoO, Cr2O3, MnO) as colouring agents since the nineteenth century was verified. The LIBS analyses allow the identification of boron on two samples, confirming the change of base glass components since the seventeenth century. The NLOM-MPEF showed the capability of this technique to measure the grisaille paint layers’ thickness. This non-invasive multi-analytical and complementary approach proves itself efficient in identifying changes in the grisaille’s composition throughout time, which can be interpreted as changes in the raw materials and manufacture used in the production of these paint materials., This research has been funded by the H2020 European project IPERION HS (Integrated Platform for the European Research Infrastructure ON Heritage Science, GA 871034), by the Spanish State Research Agency (AEI) through project PID2019-104124RB-I00/AEI/, by the Fundação de Ciência e Tecnologia de Portugal (project ref. UIDB/EAT/00729/2020, UIDP/00729/2020, LA/P/0008/2020, UIDB/ 04349/2020 and PTDC/ART-PER/1702/2021, researcher grant CEECIND/02249/2021 and doctoral grant ref. PD/BD/136673/2018) and by project TOP Heritage-CM (S2018/NMT-4372) from Community of Madrid., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Reflectance Spectroscopy as a Novel Tool for Thickness Measurements of Paint Layers

  • Dal Fovo, A.
  • Martínez-Weinbaum, Marina
  • Oujja, Mohamed
  • Castillejo, Marta
  • Fontana, Raffaella
A major challenge in heritage science is the non-invasive cross-sectional analysis of paintings. When low-energy probes are used, the presence of opaque media can significantly hinder the penetration of incident radiation, as well as the collection of the backscattered signal. Currently, no technique is capable of uniquely and noninvasively measuring the micrometric thickness of heterogeneous materials, such as pictorial layers, for any painting material. The aim of this work was to explore the possibility of extracting stratigraphic information from reflectance spectra obtained by diffuse reflectance spectroscopy (DRS). We tested the proposed approach on single layers of ten pure acrylic paints. The chemical composition of each paint was first characterised by micro-Raman and laser-induced breakdown spectroscopies. The spectral behaviour was analysed by both Fibre Optics Reflectance Spectroscopy (FORS) and Vis-NIR multispectral reflectance imaging. We showed that there is a clear correlation between the spectral response of acrylic paint layers and their micrometric thickness, which was previously measured by Optical Coherence Tomography (OCT). Based on significant spectral features, exponential functions of reflectance vs. thickness were obtained for each paint, which can be used as calibration curves for thickness measurements. To the best of our knowledge, similar approaches for cross-sectional measurements of paint layers have never been tested., This research was funded by the Spanish State Research Agency (AEI) through project PID2019-104124RB-I00/AEI/10.13039/501100011033, by project TOP Heritage-CM (S2018/NMT-4372) from Community of Madrid, and by the H2020 European project IPERION HS (Integrated Platform for the European Research Infrastructure ON Heritage Science, GA 871034)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

In-depth structural and compositional assessment of aged terpenoid varnish layers by nonlinear optical microscopy

  • Martínez-Weinbaum, Marina
  • Maestro-Guijarro, Laura
  • Carmona-Quiroga, Paula
  • Siano, S.
  • Ciofini, D.
  • Castillejo, Marta
  • Oujja, Mohamed
11 pags., 6 figs., 3 tabs., Varnishes are employed in painted artworks for protection from atmospheric pollution and oxidation and for improving the esthetic appearance by providing an even and brilliant surface finish. Also, in some cases, colored varnishes are applied intentionally to modify the chromatic appearance of paintings. Varnishes undergo complex and differentiated structural and chemical changes over time depending on their composition and conservation conditions. The present work investigates the extent of degradation of the outermost layers of varnish coatings due to aging as a function of depth by using nonlinear optical microscopy (NLOM) in the modality of multiphoton excitation fluorescence (MPEF). This non-invasive technique has been employed for the determination of the thickness, with a microscopic axial and lateral resolution, of the affected regions of pictorial terpenoid varnish layers, such as dammar, mastic, shellac and sandarac, subjected to various types and degrees of aging, artificial, natural and a combination of both. A homemade nonlinear optical microscope, based on a tightly focused pulsed femtosecond laser emitting at 800 nm, was used for the investigation. Single-photon laser-induced fluorescence (LIF) measurements served to determine the degree of surface aging and the optimum NLOM-MPEF operating conditions and helped to interpret the results obtained by applying the latter. These results signpost the correlations between the extent of degradation, non-invasively determined by NLOM-MPEF, the type and length of aging, the nature of the varnish and the initial thickness of the varnish layer., This research has been funded by the Spanish State Research Agency (AEI) through project PID2019-104124RB-I00/AEI/1013039/501100011033, by the H2020 European project IPERION HS (Integrated Platform for the European Research Infrastructure ON Heritage Science, GA 871034), and by the Community of Madrid project Top Heritage-CM (Tecnologías en Ciencias del Patrimonio, S2018/NMT_4372). Support by CSIC Interdisciplinary Platform “Open Heritage: Research and Society” (PTI-PAIS) is acknowledged., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Assessing the decorative techniques of two Art Nouveau glass windows by optical coherence tomography (OCT)

  • Palomar Sanz, Teresa
  • Iwanicka, Magdalena
  • Pombo Cardoso, Isabel
  • Vilarigues, Márcia
  • Targowski, Piotr
The images or other third party material in this article are included in the article’s Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article’s Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/. The Creative Commons Public Domain Dedication waiver (http://creativecommons.org/publicdomain/zero/1.0/) applies to the data made available in this article, unless otherwise stated in a credit line to the data., [EN] This work presents an assessment of the different decoration techniques applied in the two glass windows from the Casa-Museu Dr. Anastácio Gonçalves (Lisbon, Portugal) by Optical coherence tomography (OCT). The Dining Room glass window was found to be decorated with grisailles and acid etching, and the Atelier window with grisaille, enamel, and cold painting. The alteration state of the surface decorations was also assessed. The thicker surface decorations (grisailles and enamels) presented cracks and detachments, in contrast to the thinner lines which are normally well preserved. OCT is a suitable technique for characterizing glass decoration in situ without dismounting the stained-glass window; and able to reveal the condition and methods of manufacture that cannot be detected simply by visual inspection., This study was partial funded by the Fundação para a Ciência e a Tecnologia of Portugal (Projects ref. UID/EAT/00729/2020, UIDP/00729/2020, UIDB/ 04349/2020, PTDC/ART-OUT/5992/2020 and researcher grants CEECIND/ 02249/2021 and 2021.01436.CEECIND) and acknowledges the financial support of the Access to Research Infrastructures activity in the H2020 Programme of the EU (IPERION CH Grant Agreement n. 654028 and IPERION HS Grant Agreement n. 871034)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Assessment of silver-based calcium silicate hydrate as a novel SERS sensor

  • Maestro-Guijarro, Laura
  • Martínez-Ramírez, S.
  • Sánchez-Cortés, Santiago
  • Marco, J.F.
  • de la Figuera, Juan
  • Castillejo, Marta
  • Oujja, Mohamed
  • Carmona-Quiroga, Paula
8 pags., 10 figs., 2 tabs., This study aims at synthesizing a novel Surface-Enhanced Raman Spectroscopy (SERS) sensor based on a nanostructured substrate, calcium silicate hydrate (C-S-H), the main hydration product of Portland cement. The procedure involves first the incorporation of silver within the nanostructure of the gel (C-S-Ag-H) and second the modification of the surface of pellets of the newly synthesized material by laser irradiation at 532 nm or 355 nm. The assessment of the SERS activity revealed no amplification of the organic molecule rhodamine B (RdB) signal, used as a probe, on the C-S-Ag-H before laser irradiation. However, after laser irradiation, the SERS effect was comparable to that of reference colloidal Ag nanoparticles (NPs). This SERS response is attributed to an increase in the concentration of metallic silver on the surface of the C-S-Ag-H pellets upon laser irradiation and material ablation as revealed by X-ray Photoelectron Spectroscopy (XPS). Further enhancement of the SERS signals was induced by depositing colloidal Ag NPs on the irradiated pellets, giving rise to interparticle hot spots where the electromagnetic field is further intensified., This research has been funded by MCIN/AEI/10.13039/501100011033 through projects PID2022-137017OB-I00, PID2020-113900RB-I00 and PID2019-104124RB-I00 and by the H2020 European project IPERION HS (Integrated Platform for the European Research Infrastructure ON Heritage Science, GA 871034). Support by CSIC Platform “Open Heritage: Research and Society” (PTI-PAIS) is acknowledged. L. Maestro-Guijarro’s participation was financed by a Youth Guarantee contract (CAM20_IQFR_AI_06) from the Community of Madrid., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Quantitative spectroscopic characterization of laser-induced effects on oil paint films using 213, 266, or 2940 nm

  • Ciofini, D.
  • Martínez-Weinbaum, Marina
  • Castillejo, Marta
  • Oujja, Mohamed
  • Chillé, C.
  • Siano, S.
  • Osticioli, I.
11 pags., 6 figs., 3 tabs., Removal of aged varnish layers from easel paintings is a challenging task requiring methodologies capable of preventing any alteration of the underlying painted surface. Laser-ablation approaches using the fourth and fifth harmonics of a Q-Switched Nd:YAG (266 and 213 nm, 15 ns) and Free-Running Er:YAG laser (2940 nm, 160 µs pulses) can allow for very thin removal rates but their discrimination of the underlying paint film and self-termination potential are very limited. Thus, there is a need to develop suitable analytical methods for promptly identifying the possible occurrence of any undesired effect on the paint layer beneath the varnish, which is intentionally or unintentionally irradiated during the laser thinning treatment. Such side effects depend on the irradiation parameters and the specific material features of the pictorial film. Linseed oil paint models were prepared using lead white, vermilion, chrome yellow, ultramarine, Prussian blue and zinc white. Two distinct pigment volume concentrations (PVC) were used to investigate the dependence of the laser-induced alterations on oil binder volume ratio: low PVC (gloss paint) and high PVC (matte paint). After determining threshold exposure limits for each laser wavelength, laser-induced effects slightly above the threshold fluence were qualitatively and quantitatively assessed using FTIR and µ-Raman spectroscopies. Results showed that IR-reflectance bands of glossy and matte films exhibited appreciable shifts and distortion upon laser irradiation while reductions of the signal-to-background ratio were observed in µRaman spectra. The developed method, based on the processing of a number of spectral acquisitions, enabled for the first time the quantitative assessment and comparison of the corresponding undesired laser-induced effects in the outermost painted layer., The financial support of this work has been provided by the H2020 project IPERION HS (GA 871034), by CNR through the Short-Term Mobility Program (STM 2021), by the project CNR4CPLAS@rt” co-financed by the Tuscany Region and El.En. S.p.A., and by the Spanish State Research Agency (AEI) through projects PID2019-104124RB-I00/AEI/1013039/501100011033 and PID2022- 137017OB-I00/AEI/1013039/501100011033. Support from CSIC Interdisciplinary Platform “Open Heritage: Research and Society” (PTI-PAIS) is acknowledged., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Non-invasive stratigraphic analyzes of gelatine-based modern painting materials with linear and nonlinear optical methods

  • Quintero Balbas, Diego
  • Maestro-Guijarro, Laura
  • Carmona-Quiroga, Paula
  • Oujja, Mohamed
  • Castillejo, Marta
  • Bettini, Francesca
  • Porcinai, Simone
  • Striova, Jana
13 pags., 7 figs., 3 tabs. -- Focus Issue on Photonics for Cultural Heritage: Technological Advances and Methodological Improvements, Stratigraphic analyzes of polychrome surfaces, such as paintings, often need samples to offer consistent results regarding the sequence and composition of the layers. Non-invasive methodologies based on linear and nonlinear optical techniques limit material removal from the objects. Recently, optical coherence tomography (OCT) has become the preferred choice of heritage scientists because it is a safe and fast alternative for studying transparent or semi-transparent layers. Yet, nonlinear optical microscopy (NLOM)) technique in its modality of multiphoton excitation fluorescence (MPEF) has emerged as a promising tool for the same purpose. Here, we explored linear (OCT and confocal Raman microspectroscopy (CRM)) and nonlinear (NLOM-MPEF) optical methods’ capability to investigate gelatine-based layers in mock-up samples and a painting dated 1939 by an artist from the Surrealistic entourage. The optical behavior of mock-up samples that imitate the painting stratigraphy and of six painting fragments detached from the support was also investigated with fiber optics reflectance spectroscopy and laser induced fluorescence (LIF). Thickness values from the mock-ups obtained with OCT, CRM, and MPEF have provided evidence of the complementarity, from a millimetric to a micrometric scale, and the limitations (e.g. strong fluorescence emission in CRM) of the methods. Moreover, the presence of gelatine was ascertained by LIF spectroscopy applied to the painting fragments and NLOM-MPEF confirmed its suitability as a non-invasive technique for investigating gelatine-based stratigraphic systems., Financial support by the Access to Research Infrastructures activity in the Horizon 2020 Programme of the EU (IPERION HS Grant Agreement n.871034) is gratefully acknowledged. This research has been funded by the Diagnostica Non invaSiva e conservazione di daghErrotipi e altri materiali fotografici (DIAGNOSE) project co-funded by Tuscany Region, POR FSC 2014–2020-Axis Employment GiovaniS`ı (Grant No. CUP B53D21008070008), Museo Galileo, El.En. group, and the National Institute of Optics from the National Council of Research (CNR-INO), in collaboration with the Opificio delle Pietre Dure (OPD). Funding from the Spanish State Research Agency (AEI) through project PID2022-137017OB-I00/AEI/1013039/ 501100011033 and support from CSIC Platform ‘Open Heritage: Research and Society’ (PTI-PAIS) are also acknowledged. The authors are grateful to the Peggy Guggenheim Collection from Venice for the access to the painting fragments analysed in this work. The authors also thank Dr Carlo Galliano Lalli, for the cross-section sample available in the OPD archive. D.Q.B. is supported by Next Generation EU—Humanities and Heritage Italian Open Science Cloud (H2IOSC) project (CUP B63C22000730005)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Review and interlaboratory comparison of the Oddy test methodology

  • Díaz, Iván
  • Alvarez-Martin, Alba
  • Grau-Bové, Josep
  • Norrehed, Sara
  • Salvadori, B.
  • Kraševec, Ida
  • Duran-Romero, D.
  • Cano Díaz, Emilio
Since the introduction of the Oddy test in 1973, many museums and cultural institutions have put the method in use, developing their own versions and protocols. Currently the 3-in-1 version, temperature at 60 ºC and 2 g of tested material are set as common practice; however, other variables of the test are not standardized. The purpose of this study is to examine current versions of the Oddy test, to identify differences in the results derived from variations in the procedures, and ultimately raising awareness within the conservation community to work together towards a standardized protocol. In this article, we review the available information on the methodological differences in Oddy test protocols published in the literature related to glassware cleaning, coupon preparation, reaction vessel setup and rating of materials. Based on the review, and to highlight the many variables that could affect the results of the test, seven European cultural institutions working under the H2020 IPERION HS project performed a comparative 3-in-1 Oddy test by blindly evaluating the same ten materials. Each institution used its own test methodology but some guidelines were advised: (1) Detergents as a cleaning procedure for glassware, (2) P600 sandpaper or micromesh pad close to 1500 to prepare metal coupons and (3) 1:100 as water–air ratio. Despite this, differences between institutions’ results were still observed. Some of them are due to the differences in the coupons preparation, either in the sanding pattern or in the edge area. In order to separate the contribution of the experimental setup and the subjectivity of the evaluation in the discrepancies, coupons from all institutions have been rated by a single team of judges with experience in the Oddy Test. Results show that differences in the evaluation criteria play a relevant role in the discrepancies of the results, especially for institutions with less experience in the test. These results highlight the need to further standardize the methodology and criteria for visual assessment. Nevertheless, the Oddy test has been found to be reliable for the identification of materials that produce emissions hazardous for the conservation of cultural assets., Open Access funding provided thanks to the CRUE-CSIC agreement with Springer Nature. This research has been funded by the projects IPERION HS (European Union’s Horizon 2020 research and innovation programme, grant agreement No 871034) and TOP-HERITAGE CM (Comunidad de Madrid and European Structural Funds, Ref. S2018/NMT4372).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Preliminary study of the anti-corrosion performance of different protection systems applied to two World War II aluminium alloy archaeological objects with different surface finishes

  • Escobar Claros, Cesar
  • Brunet, Magali
  • Robbiola, Luc
  • Salvadori, Barbara
  • Brizzi, Sofia
  • Cano Díaz, Emilio
  • Ramírez Barat, Blanca
  • Liang, Haida
  • Shing Cheung, Chi
  • Targowski, Piotr
  • Iwanicka, Magdalena
  • Guilminot, Elodie
This article looks at the conservation of historic aircraft from the Second World War, testing different coatings to protect their aluminium alloy structures from corrosion. Five different protective protection systems, including Paraloid¿ B72, wax, Dinitrol¿, Multi Matt Clear Lesonal¿ and carboxylates, were evaluated by being applied to artefacts from WWII aircraft wrecks, in particular a wing fragment from a Supermarine Spitfire and a propeller blade from a P38 Lightning, which presented different surface conditions. The protected objects were exposed to real-life conditions (uncontrolled indoor environment). Advanced analytical techniques such as electrochemical impedance spectroscopy (EIS), Fourier transform infrared spectroscopy (FTIR), optical coherence tomography (OCT) and scanning electron microscopy (SEM) were used to characterize the evolution and effectiveness of the protection systems. The results showed different degrees of effectiveness for different coatings. Dinitrol¿ and Lesonal¿ demonstrated the best protective properties, forming thin but effective layers that enhance corrosion resistance. Carboxylates, on the other hand, proved ineffective, while Paraloid¿ B72 and wax were not very effective and unsuitable for objects with original paint residues, The authors would like to express their sincere gratitude to DRASSM (Département des recherches archéologiques subaquatiques et sous-marines - France), the ABSA 39–45 association for providing the objects studied in this paper and Patrick Atkinson for his contribution to the development of the hybrid OCT system at 1250 nm. We would also like to thank JPI-CH and IPERION single bond HS for their financial support. Results obtained within MOLAB Transnational Access Project EPHA (project leader Elodie Guilminot) within the EU H2020 Project IPERION HS, contract no. 871034 and conducted with the partial use of the facilities at Spanish, Italian, UK, and Polish nodes of the European Research Infrastructure for Heritage Science (E-RIHS)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Insights into the stratigraphy of gelatin-based emulsion in historical dry plate photographic negatives: A multi-analytical approach

  • Quintero Balbas, Diego
  • Maestro-Guijarro, Laura
  • Carmona-Quiroga, Paula
  • Oujja, Mohamed
  • Castillejo, Marta
  • Cattaneo, Barbara
  • Bernardoni, Andrea
  • Santagostino Barbone, Alessandra
  • Cagnini, Andrea
  • Striova, Jana
This research investigates historical gelatin dry plate negatives’ chemical composition and stratigraphic structure through a comprehensive multi-analytical approach. Our methodology integrated optical and laser-based techniques, with microscopies, including Optical and Scanning Electron Microscopy – Backscattered Electrons (SEM-BSE) and Non-linear Optical Microscopy (NLOM) in its Multi-photon Excitation Fluorescence (MPEF) modality to analyze stratigraphy. MPEF enabled us to overcome the limitations associated with light absorption encountered in other optical techniques. Chemical analysis using Laser-Induced Breakdown Spectroscopy (LIBS), Scanning Electron Microscopy – Energy Dispersive X-ray Spectroscopy (SEM-EDS), and micro-Raman spectroscopy allowed for the classification of negative types based on specific compositional materials, such as synthetic dyes. Our findings contribute to the knowledge of dry plate negative composition and stratigraphy, the aspects that have seldom been investigated. The information retrieved is crucial for understanding the realization and degradation mechanisms of these valuable artifacts, often prone to delamination and flaking, and can inform conservators to better treat historical dry plate photographic negatives., This work was supported by EU Horizon 2020 (GA n.871034), Tuscany Region (Grant No. CUP B53D21008070008), Museo Galileo, El.En. group, and the National Institute of Optics from the National Council of Research (CNR-INO), European Union NextGenerationEU – National Recovery and Resilience Plan (NRRP) (Project code IR0000029-CUP-B63C22000730005), Spanish State Research Agency (PID2022-137017OB-I00/ AEI/1013039/ 501100011033), Regional Government of Madrid (TEC-2024/TEC-39)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Protective treatments for the protection and preservation of aircraft artefacts from world war II

  • Escobar Claros, Cesar
  • DeBellis, Laura
  • Salvadori, Barbara
  • Brizzi, Sofia
  • Balbo, Andrea
  • Zanotto, Federica
  • Buratti, Elena
  • Cano Díaz, Emilio
  • Ramírez Barat, Blanca
  • Guilminot, Elodie
This study explores the effectiveness of different coatings in preserving aluminum alloy aircraft wrecks. In cultural heritage conservation, coatings must not only protect artefacts under corrosive exhibition conditions but also maintain their visual integrity and be reversible for future treatments. Three coatings were selected and tested: Paraloid¿, commonly used in conservation; Dinitrol¿, an industrial product for aluminum protection; and Cutin, a novel coating derived from recycled tomato peels. Each coating was assessed based on its protective ability, aesthetic impact, and reversibility. Paraloid¿, while aesthetically pleasing and easily reversible, offers limited protection, especially outdoors. Dinitrol¿ demonstrated superior protective qualities, with high impedance values indicating strong corrosion resistance. However, its reversibility properties are limited. Cutin showed promise as a protective coating. It is also reversible with ethanol. However, its current formulation affects the surface appearance due to residual tomato pigments., The authors would like to thank to DRASSM (Département des recherches archéologiques subaquatiques et sous-marines - France), and the ABSA 39-45 association for providing the objects studied. We are grateful to Charlène Pelé-Meziani for her support with the analyses (colorimetry and FTIR at Arc'Antique). We would also like to thank JPI-CH and IPERION-HS for their financial support. Some results obtained within MOLAB Transnational Access Project EPHA (project leader Elodie Guilminot) within the EU H2020 Project IPERION HS, contract G.A. n. 871034 and conducted with the partial use of the facilities at Spanish and Italian teams of the European Research Infrastructure for Heritage Science (E-RIHS)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Spectroanalytical approach for analysis of archaeological objects related to personal adornment from Teruel Museum

  • Maestro-Guijarro, Laura
  • Punter, Pilar
  • Menasalvas, Francisco Javier
  • Crespo, Ana
  • Sánchez-Cortés, Santiago
  • Fort González, Rafael
  • Álvarez de Buergo, Mónica
  • Carmona-Quiroga, Paula
  • Castillejo, Marta
  • Oujja, Mohamed
11 pages, 4 figures, 5 tables, The immense variety of materials found in museum's archaeological collections often makes the tasks of cataloging and conservation difficult. This is even more challenging when dealing with objects related to personal adornments, such as jewelry or amulets, due to their extensive material diversity and complexity. For these reasons, the chemical characterization of this type of objects is crucial for linking the use of certain raw materials in the production of artifacts with commercial and influential spheres. The present study aims at the non/micro-invasive material characterization of a set of heterogeneous personal adornment pieces from a wide chronological period (2nd BC – 18th AD centuries) belonging to the archaeology collection of the Teruel Museum, Spain. A multi-analytical approach, without sample taking, was applied involving Laser-Induced Breakdown Spectroscopy (LIBS), which allowed surface and in-depth elemental analysis of materials including the detection of trace elements. The LIBS results were complemented by using portable X-ray fluorescence spectrometry (p-XRF) and µ-Raman spectroscopy, which offered additional information on elemental and molecular surface composition, respectively, for accurate mineralogical identification. The analysis of the considered objects revealed the presence of a wide variety of both organic and inorganic materials that were used in the manufacturing processes, including red coral, black amber, glass, and iron, among others. This allowed for a comprehensive characterization and provided extensive details about the provenance and relative dating of the objects, information that will be useful in the elaboration of an updated catalog list and new conservation protocols for the archaeological collection of the Teruel Museum., This research is partially funded by the E-RIHS.es Spanish node of E-RIHS (European Research Infrastructure for Heritage Science) through the CSIC Program for Large European Research Infrastructures 2022, grant INFRA20004, where access was provided by the Laser Laboratory for Heritage Science at Instituto de Química Física Blas Cabrera, with the collaboration of PetroLab (Petrophysic Laboratory, Geosciences Institute, CSIC). We also acknowledge the financial support from MCIN/AEI/10.13039/501100011033/FEDER, UE through the project PID2022-137017OB-I00 and Regional Government of Madrid through the project TEC Heritage-CM (TEC-2024/TEC-39), and the H2020 European project IPERION HS (Integrated Platform for the European Research Infrastructure ON Heritage Science, GA 871034). Support by the CSIC Platform “Open Heritage: Research and Society” (PTI-PAIS) and the CSIC Open Access Publication Support Initiative through its Unit of Information Resources for Research (URICI) are also acknowledged., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Integrated Comprehensive Characterization of Black Crusts from Milan’s Monumental Cemetery: A Synergistic Approach Combining Conventional and Unconventional Analytical Techniques

  • Bergomi, Andrea
  • Comite, Valeria
  • Borelli, Mattia
  • Lombardi, Chiara Andrea
  • Festa, Elisa
  • Oujja, Mohamed
  • Castillejo, Marta
  • Maestro-Guijarro, Laura
  • Carmona-Quiroga, Paula
  • Crespo-Ibáñez, Ana
  • Pirovano, Michela
  • Fermo, Paola
21 pages, 12 figures, 4 tables . -- This article belongs to the Special Issue History, Conservation and Restoration of Cultural Heritage, Black crusts are degradation features found on stone buildings, offering valuable insights into local pollution sources. Their composition and structure reflect environmental conditions, making them important indicators for environmental and conservation studies. In this study, black crusts collected from funerary monuments in the Monumental Cemetery of Milan were comprehensively characterized using SEM-EDX, Raman spectroscopy, LIBS, and oxidative potential (OP) assays. SEM-EDX and Raman spectroscopy revealed extensive degradation of the substrate and the incorporation of pollutant-derived particles, with heavy metals such as Fe, Zn, and Pb detected in more than 90% of the samples. Correlation analysis proved effective in distinguishing major pollution sources, primarily vehicular and railway traffic, indicated by strong associations such as Zn–Mn (r = 0.896), Fe–Zn (r = 0.734), and Fe–Mn (r = 0.655), from minor sources linked to industrial emissions, reflected in correlations including Ti–Pb (r = 0.589), Pb–Cl (r = 0.702), and S–Pb (r = 0.661). Instead, LIBS analysis confirmed stratigraphic penetration of these elements beyond the surface layers, suggesting long-term accumulation. OP assays, applied here for the first time to black crusts, showed values between 0.5 and 3.0 pmol min<sup>−1</sup> µg<sup>−1</sup>, indicating moderate oxidative reactivity linked to metal content. Overall, the findings contribute to a deeper understanding of pollution-driven stone decay and support the development of more effective diagnostic and conservation strategies., This work was partly funded by the H2020 European project IPERION HS (Integrated Platform for the European Research Infrastructure ON Heritage Science, GA 871034) through a Fixlab Transnational Access. Funding from the Spanish State Research Agency (AEI) through project PID2022-137017OB-I00/AEI/1013039/501100011033, Regional Government of Madrid through the project TEC Heritage-CM (TEC-2024/TEC-39) and the support by CSIC Platform “Open Heritage: Research and Society” (PTI-PAIS) is also acknowledged. The project was also funded by the European Union—NextGenerationEU under the National Recovery and Resilience Plan (PNRR)—Mission 4 Education and research—Component 2 From research to business—Investment 1.3, Notice D.D. 341 of 15 March 2022, entitled: Cultural Heritage Active Innovation for Sustainable Society proposal code PE0000020-CUPG53C22000430006, duration until 28 February 2026., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Varnish-coated oil paints under laser treatment: Comparative surface- and depth-resolved assessment of 213 nm (15 ns), 266 nm (15 ns), and 2940 nm (160 µs) ablation regimes

  • Ciofini, Daniele
  • Maestro-Guijarro, Laura
  • Carmona-Quiroga, Paula
  • Osticioli, Iacopo
  • Castillejo, Marta
  • Siano, Salvatore
  • Oujja, Mohamed
This study employs a multi-analytical, non-invasive approach to compare the physico-chemical modifications induced by 213, 266 nm (15 ns pulse duration) and 2940 nm (160 µs) lasers in the removal of varnish films from oil paintings. Artificially aged oil paint films coated with dammar and sandarac varnishes were irradiated at threshold and supra-thresholds fluence levels. Ablation depths, residual varnish thickness (zvar) and structural changes following laser processing were non-destructively quantified via Multiphoton Excitation Fluorescence (MPEF) depth profiling. Differential Interference Contrast (DIC) microscopy revealed that morphological effects are highly wavelength-dependent. While 266 nm and 2940 nm pulses induced surface texturing via photothermal mechanisms, 213 nm irradiation promoted photolytic bond cleavage, resulting in controlled, micrometric layer-by-layer ablation. Diffuse Reflectance FTIR (DR-FTIR) and Laser-Induced Fluorescence (LIF) confirmed that physicochemical modifications may occur at 266 and 2940 nm in the underlying paint when zvar is lower than the optical penetration depth. These results provide important insights into laser-matter interactions, identifying 213 nm as an effective method for “dry” surface cleaning of picture varnishes. Conversely, 266 nm and 2940 nm lasers are better suited for integration into hybrid, solvent-based protocols, where the laser facilitates subsequent removal by mild cleaning agents., The present work has been supported by the H2020 European project IPERION HS (GA 871034), by Spanish MCIN/AEI, project PID2022-137017OB-I00, by Regional Government of Madrid, project TEC Heritage-CM (TEC-2024/TEC-39), and by the Horizon Europe Project, iPhotoCult (Project number: 101132448). Financial support for FixLab TransNational Access (TNA) activities (IPERION HS GA n.871034) for the proposal “FILMS ON TOP - Fluorescence Investigations of Laser-Modified Surfaces for improving Photonics Treatments of Oil Paintings” is gratefully acknowledged. Maestro-Guijarro thanks CSIC for the contract within the framework of the Special Intramural Project (PIE) – ref. 202680E012. Support by the CSIC Platform “Open Heritage: Research and Society” (PTI-PAIS) is also acknowledged., Peer reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

The “Historical Materials BAG”: A new facilitated access to synchrotron X-ray diffraction analyses for cultural heritage materials at the European Synchrotron Radiation Facility

  • Cotte, Marine
  • Gonzalez, Victor
  • Vanmeert, Frederik
  • Jiménez García, Nuria|||0000-0002-3737-1900
  • Albert Tortosa, Francesc|||0000-0003-3024-1342
  • Salvadó Cabré, Nativitat|||0000-0003-2266-2390
  • Janssens, Koen
(This article belongs to the Special Issue Advances in Analytical Strategies to Study Cultural Heritage Samples), The European Synchrotron Radiation Facility (ESRF) has recently commissioned the new Extremely Brilliant Source (EBS). The gain in brightness as well as the continuous development of beamline instruments boosts the beamline performances, in particular in terms of accelerated data acquisition. This has motivated the development of new access modes as an alternative to standard proposals for access to beamtime, in particular via the “block allocation group” (BAG) mode. Here, we present the recently implemented “historical materials BAG”: a community proposal giving to 10 European institutes the opportunity for guaranteed beamtime at two X-ray powder diffraction (XRPD) beamlines—ID13, for 2D high lateral resolution XRPD mapping, and ID22 for high angular resolution XRPD bulk analyses—with a particular focus on applications to cultural heritage. The capabilities offered by these instruments, the specific hardware and software developments to facilitate and speed-up data acquisition and data processing are detailed, and the first results from this new access are illustrated with recent applications to pigments, paintings, ceramics and wood., The Historical materials BAG has been implemented with support from the European Union’s Horizon 2020 research and innovation programme under grant agreement No 870313, Streamline, which also supports APC. L. H. is funded via the PANOSC project (European Union’s Horizon 2020 Research and Innovation programme under Grant Agreement No. 823852). I. F. is funded by a grant from the Marie Skłodowska-Curie COFUND Programme “InnovaXN” (contract number 847439 with the European Commission). The ESRF beamtime was granted through the peer-review BAG proposal HG-172 at ID13 and ID22 and in-house beamtime at ID21. The project on wood vessels received financial support from MINECO (Spain), Ref. PID2019-105823RB-I00. The project on cadmium red pigments was financially supported from the Horizon 2020 project IPERION-HS (H2020-INFRAIA-2019-1, GA No. 871034) and the Italian project AMIS (Dipartimenti di Eccellenza 2018–2022, funded by MIUR and Perugia University). V.G. has received funding from the European Union’s Horizon 2020 research and innovation programme under the Marie Skłodowska-Curie grant agreement No 945298-ParisRegionFP. E.A.C. and K.J. would like to acknowledge the project Smart*Light funded by the Interreg V Flanders-Netherlands program with financial support from the European Regional Development Fund (ERDF) for funding in assessing the damage caused by X-rays to model paints. K.J. acknowledges FWO (Brussels) for financial support through grants G054719N and I001919N. F.V. and K.J. acknowledge BELSPO (Brussels) for funding of the FEDtWIN mandate Macro-Imaging. C.C. (Christelle Chauffeton) is grateful to the Fondation Bettencourt-Schueller and the Cité de la Céramique Sèvres-Limoges, France for founding her work in the frame of her PhD thesis. A part of this study has been funded by the Grant-in-Aid for Scientific Research [18700680], JSPS Grant-in-Aid for Young Scientists (B) from the Ministry of Education, Culture, Sports, Science and Technology of Japan., Peer Reviewed, Article signat per 28 autors/es: Marine Cotte, Victor Gonzalez, Frederik Vanmeert, Letizia Monico, Catherine Dejoie, Manfred Burghammer, Loïc Huder, Wout de Nolf, Stuart Fisher, Ida Fazlic, Christelle Chauffeton, Gilles Wallez, Núria Jiménez, Francesc Albert-Tortosa, Nati Salvadó, Elena Possenti, Chiara Colombo, Marta Ghirardello, Daniela Comelli, Ermanno Avranovich Clerici, Riccardo Vivani, Aldo Romani, Claudio Costantino, Koen Janssens, Yoko Taniguchi, Joanne McCarthy, Harald Reichert and Jean Susini.
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

The “Historical Materials BAG”: A new facilitated access to synchrotron X-ray diffraction analyses for cultural heritage materials at the European Synchrotron Radiation Facility

  • Cotte, Marine
  • Gonzalez, Victor
  • Vanmeert, Frederik
  • Jiménez García, Nuria
  • Albert Tortosa, Francesc
  • Salvadó Cabré, Nativitat
  • Janssens, Koen
(This article belongs to the Special Issue Advances in Analytical Strategies to Study Cultural Heritage Samples), The European Synchrotron Radiation Facility (ESRF) has recently commissioned the new Extremely Brilliant Source (EBS). The gain in brightness as well as the continuous development of beamline instruments boosts the beamline performances, in particular in terms of accelerated data acquisition. This has motivated the development of new access modes as an alternative to standard proposals for access to beamtime, in particular via the “block allocation group” (BAG) mode. Here, we present the recently implemented “historical materials BAG”: a community proposal giving to 10 European institutes the opportunity for guaranteed beamtime at two X-ray powder diffraction (XRPD) beamlines—ID13, for 2D high lateral resolution XRPD mapping, and ID22 for high angular resolution XRPD bulk analyses—with a particular focus on applications to cultural heritage. The capabilities offered by these instruments, the specific hardware and software developments to facilitate and speed-up data acquisition and data processing are detailed, and the first results from this new access are illustrated with recent applications to pigments, paintings, ceramics and wood., The Historical materials BAG has been implemented with support from the European Union’s Horizon 2020 research and innovation programme under grant agreement No 870313, Streamline, which also supports APC. L. H. is funded via the PANOSC project (European Union’s Horizon 2020 Research and Innovation programme under Grant Agreement No. 823852). I. F. is funded by a grant from the Marie Skłodowska-Curie COFUND Programme “InnovaXN” (contract number 847439 with the European Commission). The ESRF beamtime was granted through the peer-review BAG proposal HG-172 at ID13 and ID22 and in-house beamtime at ID21. The project on wood vessels received financial support from MINECO (Spain), Ref. PID2019-105823RB-I00. The project on cadmium red pigments was financially supported from the Horizon 2020 project IPERION-HS (H2020-INFRAIA-2019-1, GA No. 871034) and the Italian project AMIS (Dipartimenti di Eccellenza 2018–2022, funded by MIUR and Perugia University). V.G. has received funding from the European Union’s Horizon 2020 research and innovation programme under the Marie Skłodowska-Curie grant agreement No 945298-ParisRegionFP. E.A.C. and K.J. would like to acknowledge the project Smart*Light funded by the Interreg V Flanders-Netherlands program with financial support from the European Regional Development Fund (ERDF) for funding in assessing the damage caused by X-rays to model paints. K.J. acknowledges FWO (Brussels) for financial support through grants G054719N and I001919N. F.V. and K.J. acknowledge BELSPO (Brussels) for funding of the FEDtWIN mandate Macro-Imaging. C.C. (Christelle Chauffeton) is grateful to the Fondation Bettencourt-Schueller and the Cité de la Céramique Sèvres-Limoges, France for founding her work in the frame of her PhD thesis. A part of this study has been funded by the Grant-in-Aid for Scientific Research [18700680], JSPS Grant-in-Aid for Young Scientists (B) from the Ministry of Education, Culture, Sports, Science and Technology of Japan., Peer Reviewed, Article signat per 28 autors/es: Marine Cotte, Victor Gonzalez, Frederik Vanmeert, Letizia Monico, Catherine Dejoie, Manfred Burghammer, Loïc Huder, Wout de Nolf, Stuart Fisher, Ida Fazlic, Christelle Chauffeton, Gilles Wallez, Núria Jiménez, Francesc Albert-Tortosa, Nati Salvadó, Elena Possenti, Chiara Colombo, Marta Ghirardello, Daniela Comelli, Ermanno Avranovich Clerici, Riccardo Vivani, Aldo Romani, Claudio Costantino, Koen Janssens, Yoko Taniguchi, Joanne McCarthy, Harald Reichert and Jean Susini., Postprint (published version)
Addi. Archivo Digital para la Docencia y la Investigación
Publicación Artículo científico (JournalArticle)

Advanced X-ray techniques to study the alteration of pigments in paintings

  • Monico, Letizia
  • Janssens, Koen
  • Cotte, Marine
  • Webb, Samuel M.
  • Vanmeert, Frederik
  • González, Victor
  • Van der Snickt, Geert
  • Keune, Katrien
  • Brunetti, Brunetto Giovanni
  • Falkenberg, Gerald
  • Garrevoet, Jan
  • Van Loon, Annelies
  • Vermeulen, Marc
  • Maguregui Hernando, Maite
  • De Meyer, Steven
  • Avranovich Clerici, Ermanno
  • Broers, Fréderique TH
  • Cartechini, Laura
  • De Keyser, Nouchka
  • d’Acapito, Francesco
  • Meirer, Florian
  • Romani, Aldo
  • Rosi, Francesca
  • Carboni Marri, Sara
  • Comelli, Daniela
  • Deleu, Nina
  • Fazlic, Ida
  • Ghirardello, Marta
  • Holé, Clément
  • Pérez Diez, Silvia
  • Thoury, Matthieu
  • Miliani, Costanza
The application of X-ray methods (using conventional sources or synchrotron radiation) for investigating degradation phenomena in paintings has significantly increased in the last two decades. This rise is due to their ability to provide spatially resolved elemental, molecular, and structural information from the macroscopic to the nanoscopic levels. This review will focus on the application of latest-generation X-ray techniques, including X-ray fluorescence (XRF), X-ray absorption spectroscopy (XAS), and X-ray diffraction (XRD), to study the alteration processes of pigments in paintings. The first part outlines the fundamentals of XRF, XAS, and XRD techniques and then describes the corresponding instrumental set-ups used for non-invasive macro-scale mapping of paintings and synchrotron radiation-based X-ray analysis of paint micro-samples. Subsequent sections will cover advancements in X-ray data analysis software, workflow management systems, Open Science and FAIR data initiatives, alongside practical aspects of sample preparation and issues concerning X-ray-induced damage to paints. The final section will review degradation phenomena resulting from chemical changes of selected classes of pigments. This will involve describing key findings obtained from paintings, related micro-samples, and artificially aged paint mock-ups. The outcomes discussed in this review highlight their crucial role in developing effective monitoring and preventive conservation strategies for artworks highly susceptible to degradation within heritage sites and museums., The research was financially supported by: Horizon 2020 project IPERION-HS (H2020-INFRAIA-2019–1, GA nr. 871034); the Horizon Europe project PERCEIVE (HORIZON-CL2-2021-HERITAGE-01, GA nr. 101061157); the project PE 0000020 CHANGES—CUP: B53C22003890006, NRP Mission 4 Component 2 Investment 1.3, funded by the European Union—NextGenerationEU, under the Italian Ministry of University and Research (MUR); Interreg “Vlaanderen-Nederland” project SmartLight 2.0; the BeAM (Belgian Avant Garde Modernism) project of BELSPO (Brussels, Belgium); the NanoLight Center of Excellence (Research Council, University of Antwerp, Belgium); the grant TED2021-129299A-I00 funded by MCIN/AEI/10.13039/501100011033; the Research Foundation Flanders (FWO) through its program on PhD Fellowships in Fundamental Research (application nr. 1181221N, 1181223N, 1183123N, and 1183125N). Koen Janssens and Geert Van der Snickt are indebted to the UAntwerp BOF DOCPRO project on lead-white speciation (project ID 44608). This research was also part of the activities of the Chair on Advanced Imaging Techniques for the Arts, established by the Baillet Latour fund. Koen Janssens, Ermanno Avranovich Clerici, and Steven De Meyer acknowledge financial support from the Fund for Scientific Research, Brussels, via project AutomatED (FN 7022, contract S000121N). Laura Cartechini, Francesca Rosi, and Aldo Romani thank the European Union—NextGenerationEU, Mission 4, Component 2, under the Italian Ministry of University and Research (MUR) National Innovation Ecosystem grant ECS00000041—VITALITY—CUP B43C22000470005. Katrien Keune, Fréderique T. H. Broers, and Nouchka De Keyser acknowledge the support by the Netherlands Institute for Conservation + Art + Science + (NICAS) and the Dutch Research Council (NWO) (3D2P Project, Project Nr. 628.007.031). Marine Cotte thanks the Royal Netherlands Academy of Arts and Sciences, KNAW (Descartes Huygens price 2018), and the PHC Van Gogh granted by the French Ministries of European and Foreign Affairs, and of Higher Education, Research and Innovation.