Pasar al contenido principal

ESTABILIDAD HIDRAULICA DEL MANTO, BERMAS Y CORONACION DE DIQUES EN TALUD CON REBASE Y ROTURA POR FONDO

BIA2015-70436-R

•
Nombre agencia financiadora Ministerio de Economía y Competitividad
Acrónimo agencia financiadora MINECO
Programa Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Convocatoria Proyectos I+D+i Retos de Investigación
Año convocatoria 2015
Plan Estatal 2013-2016 Plan Estatal de Investigación Científica y Técnica y de Innovación
Unidad de gestión Dirección General de Investigación Científica y Técnica
Centro beneficiario UNIVERSITAT POLITÈCNICA DE VALÈNCIA
Identificador persistente http://dx.doi.org/10.13039/501100003329

Resultados relacionados

Resultados totales (Incluyendo duplicados): 6
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Influence of Mild Bottom Slopes on the Overtopping Flow over Mound Breakwaters under Depth-Limited Breaking Wave Conditions

  • Mares-Nasarre, Patricia
  • GÓMEZ-MARTÍN, M. ESTHER|||0000-0003-1555-4383
  • Medina, Josep R.|||0000-0001-5007-7426
[EN] The crest elevation of mound breakwaters is usually designed considering a tolerable mean wave overtopping discharge. However, pedestrian safety, characterized by the overtopping layer thickness (OLT) and the overtopping flow velocity (OFV), is becoming more relevant due to the reduction of the crest freeboards of coastal structures. Studies in the literature focusing on OLT and OFV do not consider the bottom slope effect, even if it has a remarkable impact on mound breakwater design under depth-limited breaking wave conditions. Therefore, this research focuses on the influence of the bottom slope on OLT and OFV exceeded by 2% of incoming waves, hc,2% and uc,2%. A total of 235 2D physical tests were conducted on conventional mound breakwaters with a single-layer Cubipod® and double-layer rock and cube armors with 2% and 4% bottom slopes. Neural networks were used to determine the optimum point to estimate wave characteristics for hc,2% and uc,2% calculation; that point was located at a distance from the model toe of three times the water depth at the toe (hs) of the structure. The influence of the bottom slope is studied using trained neural networks with fixed wave conditions in the wave generation zone; hc,2% slightly decreases and uc,2% increases as the gradient of the bottom slope increases., This research was funded by Ministerio de Economia y Competitividad and the Fondo Europeo de Desarrollo Regional (FEDER) under grant BIA2015-70436-R and RTI2018-101073-B-I00. The first author was also financially supported by the Ministerio de Educacion, Cultura y Deporte through the FPU program (Formacion de Profesorado Universitario) under grant FPU16/05081.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Distribution of individual wave overtopping volumes on mound breakwaters

  • Molines, Jorge|||0000-0001-7850-0759
  • GÓMEZ-MARTÍN, M. ESTHER|||0000-0003-1555-4383
  • Medina, Josep R.|||0000-0001-5007-7426
  • Herrera, Maria P.
[EN] Conventional mound breakwaters are usually designed to withstand low mean wave overtopping discharges and a low proportion of overtopping waves (P-ow). Existing formulas to estimate P-ow, and maximum individual wave overtopping volume are usually based on tests with high P-ow; this study is focused on mound breakwaters subjected to P-ow, < 0.2. The performance of the 2-parameter Weibull and Exponential distributions is examined in order to describe individual wave overtopping volumes of mound breakwaters in non-breaking wave conditions. A new methodology is applied to 164 small-scale 2D physical tests to identify the number of overtopping waves, and the corresponding individual wave overtopping volumes. Utility functions are used to consider the relative relevance of the observed data: in this study, a quadratic utility function depending on all the individual wave overtopping volumes and step utility functions with 10%, 30% and 50% of the highest volumes are used to fit the Weibull and Exponential distributions. In this study, a new estimator of P-ow is proposed to improve the predictions required to estimate the maximum individual wave overtopping volume. Existing estimators of P-ow, underpredict the largest values of P-ow, measured in the physical tests. The parameters fitted to the Weibull and Exponential distributions using the quadratic utility function provide estimations of the dimensionless maximum individual wave overtopping volume with relative mean squared errors rMSE = 10.4% and 10.6%, respectively. When CLASH Neural Network-estimated mean overtopping rates are used to predict the maximum individual wave overtopping with the quadratic utility function, the 2-parameter Weibull and Exponential distributions provide rMSE = 31.6% and rMSE = 33.3%, respectively. The new estimators proposed in this study improve the predictions of P-ow and maximum individual wave overtopping volumes on conventional mound breakwaters designed for low wave overtopping rates., The authors are grateful for financial support from European FEDER and Spanish Ministerio de Economia y Competitividad (Grants BIA2012-33967 and BIA2015-70435-R), SATO (OHL Group), Universitat Politecnica de Valencia (Grant SP20180111, Primeros Proyectos de Investigacion (PAID-06-18), Vicerrectorado de Investigacion, Innovacion y Transferencia de la Universitat Politecnica de Valencia) and CDTI (Centro para el Desarrollo Tecnologico e Industrial). The authors also thank Debra Westall for revising the manuscript.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Overtopping layer thickness and overtopping flow velocity on mound breakwaters

  • Mares-Nasarre, Patricia
  • Argente-Garrido, Gloria Maria
  • GÓMEZ-MARTÍN, M. ESTHER|||0000-0003-1555-4383
  • Medina, Josep R.|||0000-0001-5007-7426
[EN] Mound breakwater design is evolving owing to rising sea levels caused by climate change and social concern regarding the visual impact of coastal structures. The crest freeboard of coastal structures tends to decrease while overtopping hazard increases over time. Pedestrian safety when facing overtopping events on coastal structures has been assessed considering the overtopping layer thickness (OLT) and overtopping flow velocity (OFV). This paper proposes a new method to estimate the OLT and OFV on mound breakwater crests during extreme overtopping events, based on 123 2D small-scale physical tests of conventional low-crested mound breakwaters with a single-layer Cubipod® and double-layer rock and cube armors. The new method to estimate OLT exceeded by 2% of incoming waves is based on formulas given in literature for dikes, but adapted and calibrated for mound breakwaters. The formula to estimate the OFV exceeded by 2% of incoming waves is based on the correlation between the statistics of the OLT and OFV, considering an empirical coefficient calibrated for each type of armor layer. Exponential and Rayleigh distribution functions are proposed for estimating the OLT and OFV with exceedance probabilities under 2%. Although the statistics of OLT and OFV depend on similar variables, contrary to intuition, specific OLT and OFV corresponding to the same overtopping event appear to be independent., The authors acknowledge the financial support from the Ministerio de Economfa y Competitividad and the Fondo Europeo de Desarrollo Regional (FEDER) under grant BIA2015-70436-R, and from the Conselleria d'Educacio, Investigacia, Cultura i Esport (Generalitat Valenciana) under grant GV/2017/031. The first author was financially supported through the FPU program (Formacion de Profesorado Universitario) funded by the Ministerio de Education, Cultura y Deporte under grant FPU16/05081.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Hydraulic Stability of the Armor Layer of Overtopped Breakwaters

  • Argente-Garrido, Gloria Maria
  • GÓMEZ-MARTÍN, M. ESTHER|||0000-0003-1555-4383
  • Medina, Josep R.|||0000-0001-5007-7426
[EN] Mound breakwaters with significant overtopping rates in depth-limited conditions are common in practice due to social concern about the visual impact of coastal structures and sea level rise due to climatic change. For overtopped mound breakwaters, the highest waves pass over the crest producing armor damage, not only to the front slope, but also to the crest and the rear slope. To guarantee the breakwater stability, it is necessary to limit the armor damage in the three parts of the structure: Front slope, crest, and rear slope. This paper describes the hydraulic stability of the armor layer of medium and low-crested structures in wave breaking conditions. Small-scale physical model tests were carried out with different relative crest freeboards and three armor units: Rocks, cubes, and Cubipods. The armor damage progression in the front slope, crest, and rear slope was analyzed using the Virtual Net method to consider the heterogeneous packing and porosity evolution along the armor slope. A comparison is provided between the hydraulic stability of the different armors and their relationship with the measured overtopping volumes., This research was funded by Ministerio de Economia y Competitividad and the FondoEuropeo de Desarrollo Regional (FEDER) under grant BIA2015-70436-R.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Estimations of wave forces on crown walls based on wave overtopping rates

  • Molines, Jorge|||0000-0001-7850-0759
  • Medina, Josep R.|||0000-0001-5007-7426
  • Herrera Gamboa, María Piedad
[EN] In this study, seven input variables are used to estimate wave forces on the crown wall, and explanatory variables are ranked using neural network techniques. 274 small-scale 2D tests, including both wave overtopping and pressure on crown-wall measurements, were used to calibrate the wave force predictors. Wave overtopping (log Q) was the most relevant variable to estimate horizontal wave forces and overturning moments, while the relative foundation level (F-e/L-0p) was the most relevant variable to estimate wave up-lift forces. The new wave force estimators showed prediction errors slightly higher than the formulas given in the literature, but using fewer parameters and explanatory variables. The range of application of the new formulas is 1.67 < R-c/(gamma(f) H-m0) < 6.55, 1.39 < xi(0p) < 7.77, 0.36 < gamma(f) R-u0.1%/R-c < 1.41, 0.00 < (R-c-A(c))/C-h < 0.59, 2.64 < root L-m/G(c) < 6.54, 0.00 < F-c/ L-0p < 0.03 and -6.00 < logQ < -2.78. Compared to pressure on crown walls, the mean wave overtopping rate is relatively easy to measure in small-scale tests and prototypes. The new estimators of wave forces on the crown wall can be used to indirectly calculate forces on models when only overtopping rates are measured. If wave overtopping is one order of magnitude higher, the wave forces and overturning moments on the crown wall increase between 11% and 60%, considerably reducing the crown wall stability., The authors acknowledge financial support from European FEDER and Spanish Mirtisterio de Economia y Competitividad (Grant BIA2015-70436-R), SATO (OHL Group) and CDTI. The second author was funded through the FPU program (Formacion del Profesorado Universitario, Grant FP2013/01872) by the Spanish Ministerio de Educacion, Culturay Deporte. The authors thank Debra Westall for revising the manuscript.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Hydraulic stability of rock armors in breaking wave conditions

  • Herrera Gamboa, María Piedad
  • GÓMEZ-MARTÍN, M. ESTHER|||0000-0003-1555-4383
  • Medina, Josep R.|||0000-0001-5007-7426
[EN] Armor layers of mound breakwaters are usually designed with empirical formulas based on small-scale tests in non-breaking wave conditions. However, most rubble mound breakwaters are constructed in the depth-induced breaking zone, where they must withstand design storms having some percentage of large waves breaking before reaching the structure; in these cases, the design formulas for non-breaking wave conditions are not fully valid. To characterize double-layer rock armor damage in breaking wave conditions, 2D physical model tests were carried out with a bottom slope m=1/50. In order to develop a simple method to determine the wave parameters in the depth-induced breaking zone, experimental wave measurements were compared to the numerical estimations given by the SwanOne model. An analysis was conducted to select the best characteristic wave height to estimate rock armor damage when dealing with depth-induced breaking waves; the spectral significant wave height, Hm0, estimated at a distance of 3hs seaward from the structure toe, was found to be the most adequate. A new hydraulic stability formula is proposed for double-layer rock armors in breaking wave conditions, considering the observed potential 6-power relationship between the equivalent dimensionless armor damage and the Hm0 at 3hs seaward distance from the structure toe., The authors acknowledge the financial support from the Spanish Ministry of Economy and Competitiveness (grants BIA2012-33967 and BIA2015-70436-R). The first author was financially supported through the FPU program (Formacion del Profesorado Universitario) funded by the Spanish Ministry of Education (Ministerio de Educacion, Cultura y Deporte) FPU13/01872. The authors thank Debra Westall for revising the manuscript.