Pasar al contenido principal

DISPOSITIVOS Y SISTEMAS FOTONICOS SENSORES PARA ESTRUCTURAS INTELIGENTES Y EVALUACION NO DESTRUCTIVA II

PID2019-107270RB-C22

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Convocatoria Proyectos de I+D+i (Generación de Conocimiento y Retos Investigación)
Año convocatoria 2019
Plan Estatal 2017-2020 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario UNIVERSIDAD PUBLICA DE NAVARRA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 19
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Effect of Linewidth on the Relative Intensity Noise in Random Distributed Feedback Raman Fiber Lasers

  • Rota-Rodrigo, S.
  • Leandro, D.
  • Santarelli, G.
  • López-Amo, Manuel
  • Ania Castañón, Juan Diego
Artículo con 5 figuras, We experimentally explore the relation between spectral linewidth and RIN transfer in half-open cavity random distributed feedback Raman lasers, demonstrating for the first time the possibility of adjusting the pump-to-signal RIN transfer intensity and cut-off frequency by using spectral filtering in the reflector section. We apply this approach to a 50-km laser system, operating in the C-Band, reliant on a standard single-mode fiber. We obtained a minimum bandwidth of 13 pm, which translates into a visible RIN cut-off at 800 MHz., This research was funded by the Spanish Government grants RTI2018-097957-B-C33, PID2021-128000OB-C21, and PID2019-107270RB-C22; Conseil Régional d’Aquitaine (2017-1R50302-00013493); LAPHIA (Lasers and Photonics in Aquitaine); the Horizon 2020 Framework Programme (H2020) (Marie Sklodowska-Curie—748839); and Comunidad de Madrid project SINFOTON2-CM (S2018-NMT/4326). Additional support was from AEI/FEDER funds.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Cross Sections for Electron Scattering from Cadmium: Theory and Experiment

  • Marinković, B. P.
  • McEachran, R. P.
  • Fursa, D. V.
  • Bray, I.
  • Umer, H.
  • Blanco, F.
  • García, Gustavo
  • Brunger, M. J.
  • Campbell, L.
  • Jones, D. B.
12 pags., 5 figs. -- This paper is dedicated to Professor Michael Brunger, who coordinated the collaborative contributions, Results from the application of optical potential, relativistic optical potential, relativistic convergent close-coupling, and binary encounter Bethe models to electron scattering from gas-phase cadmium are presented. In particular, integral cross sections for elastic scattering, summed discrete electronic-state excitation, and ionization scattering processes are reported over an extended incident electron-energy range. Total cross sections are constructed by taking their sum. Measurements are presented for elastic scattering and for excitation to the 51P1 state. The theoretical and experimental results are compared to previous calculations and measurements. Recommended electron cross-section datasets are constructed over an incident electron energy range of 0.01-10 000 eV., This work was financially supported, in part, by the Australian Research Council (ARC) DP180101655, DP190100696, and DP220101480 projects; in part, by the Institute of Physics University Belgrade, through the grant by the Ministry of Education, Science and Technological Development of the Republic of Serbia (Grant No. 451-03-9/2021-14); in part, by the Spanish Ministry of Science and Innovation (Project Nos. PID2019-10727RB-C21 and C22); and, in part, by resources provided by the Pawsey Supercomputing Centre with funding from the Australian Government and the Government of Western Australia. D.B.J. is the recipient of an ARC Future Fellowship (Grant No. FT210100264) funded by the Australian Government., Peer reviewed
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Compensation of phase noise impairments in distributed acoustic sensors based on optical pulse compression time-domain reflectometry

  • Piñeiro Ben, Enrique
  • Sagüés García, Mikel
  • Loayssa Lara, Alayn
We introduce a method to compensate for the deleterious effects of the phase noise of the laser source on long-range distributed acoustic sensors (DAS) that implement optical pulse compression (OPC). Pulse compression can be used in coherent optical time-domain reflectometry (COTDR) sensors to extend the measurement range without compromising spatial resolution. In fact, OPC-COTDR sensors have demonstrated the longest measurement range to date in passive sensing links that do not require distributed amplification to compensate fiber attenuation. However, it has been found that the limited coherence of the laser source has a degrading effect on the actual performance enhancement that pulse compression can bring because it constrains the maximum duration of the compression waveforms that can be used and makes the use of lasers with extremely low phase noise necessary.We introduce a technique to compensate for the effects of phase noise on OPC-COTDR sensors so that they can demonstrate their full potential for long-range measurements using lasers with less stringent phase noise requirements. The method is based on sampling the phase noise of the laser with an auxiliary interferometer and using this information in a simple signal processing technique to mitigate its deleterious effect on the signal measured. We test our method in an OPCCOTDR sensor that uses 500-μs linear frequency modulated pulses to demonstrate 100-km range measurements with 200 p/√Hz of strain sensitivity at 2-m initial spatial resolution that becomes 10-m after applying the gauge length. To our knowledge, this is the longest compression waveform demonstrated to date in an OPCCOTDR sensor. Its use provides an extra 20-km range compared to previous demonstrations using laser sources of comparable linewidth. Furthermore, comparable performance is also demonstrated when using a laser source with an order of magnitude larger linewidth., This work was supported in part by European Union “Next generationEU”/PRTR and MCIN/AEI/10.13039/501100011033 under grant PDC2021-121172-C21, in part by FEDER “A way to make Europe” and MCIN/AEI/10.13039/501100011033 under Grant PID2019-107270RB-C22, and in part by the Gobierno de Navarra under Grant PC210-211 FIBRATRAFIC.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

C and L band fiber lasers enhanced by ultrafast laser inscribed artificial backscatter reflectors

  • Pérez Herrera, Rosa Ana
  • Roldán Varona, Pablo
  • Sánchez González, Arturo
  • Rodríguez Cobo, Luis
  • López Higuera, José Miguel
  • López-Amo Sáinz, Manuel
This letter presents an experimental comparison between two linear-cavity erbiumdoped fiber lasers (EDFL) assisted by two different artificial backscatter fiber-based reflectors. Both reflectors were inscribed by femtosecond laser direct writing, one of them within a single-mode fiber (SMF) and the other one within a multi-mode fiber (MMF). Although the erbium-doped fiber amplifier (EDFA) used in both structures was the same and both reflectors were manufactured under the same parameters, the reflection spectrum of each was clearly different due to their different physical properties. The first linear-cavity EDFL, consisting of an SMF-based reflector with 9µm core and 125µm cladding, resulted in a single laser emission line located in the C-band and centered at 1564.4 nm, exhibiting an optical signal-to-noise ratio (OSNR) of 52dB when pumped at 100mW. On the other hand, a single laser emission line with a similar OSNR but in L-band (centered at 1574.5nm) was obtained when using an MMF-based reflector with 50µm core and 125µm cladding., Ministerio de Educacion, Cultura y Deporte (PhD grant FPU2018/02797); European Commission (Next generation EU/PTR); FEDER (A way to make Europe); MCIN/AEI/10.13039/501100011033 (PDC2021-121172-C21, PID2019-107270RB).
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Cavidad láser de fibra óptica multibanda basada en reflectores pseudoaleatorios cuasidistribuidos

  • Sánchez González, Arturo
  • Pérez Herrera, Rosa Ana
  • Roldán Varona, Pablo
  • Rodríguez Cobo, Luis
  • López Higuera, José Miguel
  • López-Amo Sáinz, Manuel
Trabajo presentado a la XIII Reunión Nacional de Óptica, 22-24 Noviembre 2021, En este trabajo se presenta un análisis experimental de las prestaciones alcanzadas por una cavidad láser en línea asistida por un reflector de fibra con retrodispersión controlada artificialmente (RFRCA). Dicho reflector ha sido concebido para permitir oscilación en un único modo longitudinal (SLM) en bandas C y L, presentando inestabilidades en potencia de emisión inferiores a 0.1 dB y relaciones de señal óptica a ruido (OSNR) superiores a 44 dB., Trabajo financiado por MICINN y AEI (PID2019-107270RB); fondos FEDER; MECD (Beca PFU 2018/02797); y los Proyectos de Jóvenes Investigadores de la UPNA 2019 (PJUPNA1928).
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Wavelength-switchable L-band fiber laser assisted by random reflectors

  • Pérez Herrera, Rosa Ana
  • Roldán Varona, Pablo
  • Sánchez González, Arturo
  • Rodríguez Cobo, Luis
  • López Higuera, José Miguel
  • López-Amo Sáinz, Manuel
A wavelength-switchable L-band erbium-doped fiber laser (EDFL) assisted by an artificially controlled backscattering (ACB) fiber reflector is here presented. This random reflector was inscribed by femtosecond (fs) laser direct writing on the axial axis of a multimode fiber with 50 lm core and 125 lm cladding with a length of 17 mm. This microstructure was placed inside a surgical syringe to be positioned in the center of a high-precision rotation mount to accurately control its angle of rotation. Only by rotating this mount, three different output spectra were obtained: a single wavelength lasing centered at 1574.75 nm, a dual wavelength lasing centered at 1574.75 nm and 1575.75 nm, and a single wavelength lasing centered at 1575.5 nm. All of them showed an optical signal-to-noise ratio (OSNR) of around 60 dB when pumped at 300 mW, This work was financed by the program "José Castillejo para estancias de movilidad en el extranjero de jóvenes doctores", funded by the Ministerio de Universidades of Spain (reference CAS21/00351); the Spanish AEI projects PID2019-107270RB, funded by MCIN/AEI/10.13039/501100011033 and FEDER "A way to make Europe", and projects PDC2021-121172 and TED2021-130378B funded by MCIN/ AEI/10.13039/501100011033 and European Union "Next generation EU"/PTR. Finally, the work was also founded by the Ministerio de Educación, Cultura y Deporte of Spain (PhD grant FPU2018/02797).
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Design of optical fiber Bragg grating-based sensors for flow measurement in pipes

  • Diéguez Elizondo, Pedro
  • Rodríguez Rodríguez, Armando
  • Urroz Unzueta, José Carlos
  • López Rodríguez, José Javier
  • López-Amo Sáinz, Manuel
In this work, optical Fiber Bragg grating (FBG) sensors were used to measure water flow in pipes. Several types of coatings were incorporated into the design of the sensors to examine their effects on the elastic strain that the fiber underwent as a result of the water flow. ANSYS-CFX V2020 R2 software was used to model the elastic strain encountered by the fiber under various flow rates in order to assess the performance of the FBG sensors. The calculations and experimental data exhibited good convergence, demonstrating the accuracy of the FBG sensors in determining water flow. These calculations and procedures can be extrapolated to any other fluid., This work was supported in part by projects PID2019-107270RB-C02, funded by MCIN/AEI/10.13039/501100011033 and FEDER “A way to make Europe”, and TED2021-130378B-C22 funded by MCIN/AEI/10.13039/501100011033 and European Union “Next generation EU”/PTR.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Multiparameter sensor based on a multiinterferometric serial configuration for temperature and strain measurements

  • Pérez Herrera, Rosa Ana
  • Bravo Acha, Mikel
  • Leandro González, Daniel
  • Novais, Susana
  • Pradas Martínez, Javier
  • López-Amo Sáinz, Manuel
In this work, a multi-parameter point sensor based on the combination of Fabry-Perot (FP) and the anti-resonant (AR) reflecting guidance in cascade configuration is proposed and experimentally demonstrated. This structure, based on FP interference and AR reflecting guidance, was fabricated with two different air micro-cavities. The attained experimental results showed different strain and temperature sensitivities for the antiresonance contribution. However, when analyzing the FP interference, only strain sensitivity was observed, demonstrating that this air micro-cavity was also insensitive to temperature variations., This work was supported by the Spanish AEI projects TEC2016-76021-C2 and PID2019-107270RB-C22, FEDER Funds, the European Union’s Horizon 2020 research and innovation programme under the Marie Skłodowska-Curie grant agreement No 838143, Projects for young researches UPNA 2019, “Caja Navarra” and “la Caixa” foundations under agreement LCF/PR/PR13/51080004 and the grant BGP18/00180 of the “Beatriz Galindo” programme from the Spanish Ministry of Science, Innovation and Universities.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Ring cavity erbium-doped fiber for refractive index measurements

  • Pérez Herrera, Rosa Ana
  • Soares, Liliana
  • Silva, Susana
  • Frazão, Orlando
In this study, an interrogation system based on an erbium-doped fiber ring cavity for refractive index measurements is presented and experimentally demonstrated. This cavity ring includes a 1 × 3 coupler wherein one of the fiber output ports is used to increase the optical power of the system by means of an FBG used as a reflector. The other two output ports are used as a refractive index sensing head and reference port, respectively. An experimental demonstration of this proposed sensor system for the measurement of a distinct refractive index is presented., This work is financed by the program “José Castillejo para estancias de movilidad en el extranjero de jóvenes doctores”, funded by the Ministerio de Universidades of Spain (reference CAS21/00351); project PID2019-107270RB-C22, funded by MCIN/AEI/10.13039/501100011033 and FEDER “A way to make Europe”; projects PDC2021-121172-C21 and TED2021-130378B-C22 funded by MCIN/AEI/10.13039/501100011033 and European Union “Next generation EU”/PTR; and National Funds through the Portuguese funding agency, FCT—Fundação para a Ciência e a Tecnologia, within project UIDB/50014/2020. Liliana Soares acknowledges the support of FCT, Portugal through the Grant 2020.05297.BD.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

High frequency vibration sensor using a fiber laser with a multicore fiber interferometer

  • Correa Serrano, Ángel Ignacio
  • Galarza Galarza, Marko
  • Dauliat, Romain
  • Jamier, Raphael
  • Roy, Philippe
  • López-Amo Sáinz, Manuel
  • Pérez Herrera, Rosa Ana
We present an interferometric vibration sensor that uses three-core fibers. The transducer is constructed by splicing a segment 20 mm long of a multicore optical fiber (MCF) to a single-mode optical fiber (SMF). The end of the MCF segment is cut off and painted using silver metallic paint. The sensor head is operated in reflection mode. The structure is placed on a polyvinyl chloride (PVC) plate, which is excited with a wide range of frequency signals. The vibrations induce cyclic bending in the MCF segment, resulting in periodic oscillations of the reflected interference spectrum. This device is demonstrated to be suitable to measure vibrations in a frequency range of the order of 300 kHz detecting deformations as small as 0.40μm ., This work was supported in part by projects PID2019-107270RB-C02 and PID2022- 137269OB-C21, funded by MCIN/AEI/10.13039/501100011033 and FEDER “A way to make Europe,” and TED2021-130378B-C22 funded by MCIN/AEI/10.13039/501100011033 and European Union “Next generation EU”/PRTR.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Microdrilled tapers to enhance optical fiber lasers for sensing

  • Pérez Herrera, Rosa Ana
  • Bravo Acha, Mikel
  • Roldán Varona, Pablo
  • Leandro González, Daniel
  • Rodríguez Cobo, Luis
  • López Higuera, José Miguel
  • López-Amo Sáinz, Manuel
In this work, an experimental analysis of the performance of different types of quasi-randomly distributed reflectors inscribed into a single-mode fiber as a sensing mirror is presented. These artificially-controlled backscattering fiber reflectors are used in short linear cavity fiber lasers. In particular, laser emission and sensor application features are analyzed when employing optical tapered fibers, micro-drilled optical fibers and 50 μm-waist or 100 μm-waist micro-drilled tapered fibers (MDTF). Single-wavelength laser with an output power level of about 8.2 dBm and an optical signal-to-noise ratio of 45 dB were measured when employing a 50 μm-waist micro-drilled tapered optical fiber. The achieved temperature sensitivities were similar to those of FBGs; however, the strain sensitivity improved more than one order of magnitude in comparison with FBG sensors, attaining slope sensitivities as good as 18.1 pm/με when using a 50 μm-waist MDTF as distributed reflector., This work is part of the project PID2019-107270RB, funded by MCIN/ AEI/10.13039/501100011033 and FEDER 'A way to make Europe', the Ministerio de Educación, Cultura y Deporte of Spain (PhD grant FPU2018/02797), the European Union’s Horizon 2020 research and innovation programme under the Marie Skłodowska-Curie grant agreement No 838143, the Beatriz Galindo BEAGAL18/00116 fellowship, the 'Fundación Caja Navarra' and 'Fundación la Caixa' with the proyect LCF/PR/PR13/51080004 and Projects for young researchers UPNA 2019.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Study of in-line capillary fiber sensor for uniaxial transverse deformation

  • Sánchez González, Arturo
  • Leandro González, Daniel
  • Dauliat, Romain
  • Jamier, Raphael
  • Roy, Philippe
  • Pérez Herrera, Rosa Ana
This research explores the impact of cyclic uniaxial transverse deformation on an in-line hollow-core fiber etalon. The structure consists of a 6 mm long section of capillary fiber spliced between two standard single-mode fibers. The optical response of the structure is theoretically analyzed in spectral and transformed domains, evidencing Fabry-Perot and antiresonant interferometric mechanisms. A validation of the theoretical behavior is carried out both through simulation and experimentation. The performance of the structure for uniaxial transverse deformation is subsequently evaluated by tracking the phase of the main component in the transformed domain. The relevance of measuring in the time domain is discussed, demonstrating improved accuracy over wavelength shift and inverse spatial domain methods. Several sensors with different internal diameters underwent cycles of transverse deformation, revealing robust linear trends in every case. On average, the structure demonstrated elastic behavior under deformations up to 42 μm, with a mean sensitivity of 0.174 rad/μm, and mechanical breakage taking place at 58 μm. The results confirmed the suitability of the sensor to withstand uniaxial micro-displacements or pressures, with smaller inner diameter capillary fibers showing the best performance., This work was supported in part by MCIN/AEI/10.13039/501100011033 and FEDER "A way to make Europe" under Project PID2019-107270RB-C22 and Project PID2022-137269OB-C21, in part by MCIN/AEI/10.13039/501100011033 and European Union "Next generation EU"/PRTR under Project PDC2021-121172-C21 and Project TED2021- 130378B-C22, and in part by the Public University of Navarre under Project PJUPNA06-2022. Open access funding provided by Public University of Navarre.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Long-range traffic monitoring based on pulse-compression distributed acoustic sensing and advanced vehicle tracking and classification algorithm

  • Corera Orzanco, Íñigo
  • Piñeiro Ben, Enrique
  • Navallas Irujo, Javier
  • Sagüés García, Mikel
  • Loayssa Lara, Alayn
We introduce a novel long-range traffic monitoring system for vehicle detection, tracking, and classification based on fiber-optic distributed acoustic sensing (DAS). High resolution and long range are provided by the use of an optimized setup incorporating pulse compression, which, to our knowledge, is the first time that is applied to a traffic-monitoring DAS system. The raw data acquired with this sensor feeds an automatic vehicle detection and tracking algorithm based on a novel transformed domain that can be regarded as an evolution of the Hough Transform operating with non-binary valued signals. The detection of vehicles is performed by calculating the local maxima in the transformed domain for a given time-distance processing block of the detected signal. Then, an automatic tracking algorithm, which relies on a moving window paradigm, identifies the trajectory of the vehicle. Hence, the output of the tracking stage is a set of trajectories, each of which can be regarded as a vehicle passing event from which a vehicle signature can be extracted. This signature is unique for each vehicle, allowing us to implement a machine-learning algorithm for vehicle classification purposes. The system has been experimentally tested by performing measurements using dark fiber in a telecommunication fiber cable running in a buried conduit along 40 km of a road open to traffic. Excellent results were obtained, with a general classification rate of 97.7% for detecting vehicle passing events and 99.6% and 85.7% for specific car and truck passing events, respectively., This work was supported in part by European Union “Next generationEU”/PRTR and MCIN/AEI/10.13039/501100011033 under grant PDC2021-121172-C21, in part by FEDER “A way to make Europe” and MCIN/AEI/10.13039/501100011033 under grant PID2019-107270RB, and in part by Gobierno de Navarra under grant PC210-211 FIBRATRAFIC.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

High performance fiber laser resonator for dual band (C and L) sensing

  • Sánchez González, Arturo
  • Pérez Herrera, Rosa Ana
  • Roldán Varona, Pablo
  • Rodríguez Cobo, Luis
  • López Higuera, José Miguel
  • López-Amo Sáinz, Manuel
This work presents an experimental analysis and comparison of the performance of quasi-randomly distributed reflectors inscribed into a single-mode fiber as a sensing mirror both in C- and L-band. Single-wavelength emission has been obtained in either band when using these artificially controlled backscattering fiber reflectors in a ring-cavity fiber laser. Single-longitudinal mode operation with an optical signal to noise ratio (OSNR) of 47 dB and an output power instability as low as 0.04 dB have been measured when employing a C-band optical amplifier. When replaced by an L-band optical amplifier, a single-longitudinal mode behavior has also been obtained, showing an OSNR of 44 dB and an output power instability of 0.09 dB. Regarding their performance as fiber-laser sensing systems, very similar temperature and strain sensitivities have been obtained in both bands, comparable to fiber Bragg grating sensors in the case of temperature and one order of magnitude higher in the case of strain variations., and European Union “Next generationEU”/PTR.This work is part of the project PID2019-107270RB, funded by MCIN/ AEI/10.13039/501100011033 and FEDER “A way to make Europe”, the Ministerio de Educación, Cultura y Deporte of Spain (PhD grant FPU2018/02797), and PDC2021-121172, funded by MCIN/ AEI/10.13039/501100011033
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Paracetamol concentration-sensing scheme based on a linear cavity fiber laser configuration

  • Soares, Liliana
  • Pérez Herrera, Rosa Ana
  • Novais, Susana
  • Ferreira, António
  • Frazão, Orlando
  • Silva, Susana
A paracetamol concentration-sensing scheme based on a linear cavity fiber laser configuration is demonstrated experimentally. The laser cavity has a fiber sensor at one end, that allows refractive index measurements. The refractometer consists of a cleaved fiber tip combined with an FBG functioning as a reflecting mirror. The combination of a fiber loop mirror at the other end allows to reflect all the light from the FBG and refractometer, forming a linear cavity. By measuring the intensity variation of the Fresnel reflection at the fiber-to-liquid interface, the measured concentration is linear and have a concentration sensitivity of -8.74±0.34×10-5 µW/(g/kg), over a range of 52.61 to 219.25 g/kg, and with a resolution of 2.77 g/kg. The results obtained present high stability and prove the potential of the fiber laser system to performed real-time measurements of concentration, in a non-invasive way., This research was funded by: National Funds through the Portuguese funding agency, FCT - Fundação para a Ciência e a Tecnologia, within project UIDB/50014/2020; National Funds through FCT/MCTES (PIDDAC), within projects LA/P/0045/2020 (ALiCE), UIDB/00511/2020 and UIDP/00511/2020 (LEPABE); Program “José Castillejo para estancias de movilidad en el extranjero de jóvenes doctores”, funded by the Ministerio de Univesidades of Spain (reference CAS21/00351); project PID2019-107270RB-C22, funded by MCIN/AEI/https://doi.org/10.13039/501100011033 and FEDER “A way to make Europe”; projects PDC2021-121172-C21 and TED2021-130378B-C22 funded by MCIN/ AEI/https://doi.org/10.13039/501100011033 and European Union “Next generation EU”/PTR. Liliana Soares acknowledges the support of FCT, Portugal, through the Grant 2020.05297.BD.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Phase noise effects on phase-sensitive OTDR sensors using optical pulse compression

  • Loayssa Lara, Alayn
  • Sagüés García, Mikel
  • Eyal, Avishay
We introduce a detailed theoretical, numerical, and experimental study of the effects of laser's phase noise on the performance of phase-sensitive optical time-domain reflectometry (-OTDR) sensors that use optical pulse compression (OPC). Pulse compression is a technique that can be used to improve the received signal amplitude by increasing the effective energy of the pulses that are launched into the fiber without degrading the spatial resolution of the measurements. Therefore, it is a valuable tool to extend the range of these sensors and mitigate fiber attenuation constraints. However, it has been observed that the limited coherence of the laser source has a degrading effect on the actual performance enhancement that this method can provide. Here, we derive a theoretical model that can be used to quantify this degradation for any type of OPC such as those based on either linear frequency modulation (LFM) pulses or perfect periodic autocorrelation (PPA) bipolar bit sequences. The model facilitates numerical estimation of the sensitivity of the -OTDR measurements. It also produces theoretical expressions for the mean and the variance of the phase-noise perturbed backscatter response. These results are validated via numerical simulations and experiments in -OTDR setups using LFM as well as PPA OPC. Furthermore, we demonstrate the use of the model to investigate the basic trade-offs involved in the design of OPC -OTDR systems., This work is part of the project PDC2021-121172-C21 funded by MCIN/AEI/10.13039/501100011033 and European Union ‘Next generationEU’/PRTR, and of project PID2019- 107270RB, funded by MCIN/AEI/10.13039/501100011033 and FEDER ‘A way to make Europe’. The work was supported in part by the Israeli Science Foundation (ISF), grant number 2675/20.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Two-wavelength phase-sensitive OTDR sensor using perfect periodic correlation codes for measurement range enhancement, noise reduction and fading compensation

  • Sagüés García, Mikel
  • Piñeiro Ben, Enrique
  • Cerri, Enis
  • Minardo, Aldo
  • Eyal, Avishay
  • Loayssa Lara, Alayn
We demonstrate a two-wavelength differential-phase-measuring OTDR sensor that uses perfect periodic correlation phase codes to enhance the measurement performance. The two-wavelength technique extends the measurement range of OTDR sensors by synthesizing a virtual longer-wavelength measurement from two simultaneous measurements of phase using different lasers. This increases the range free from phase unwrapping errors. However, we find that the application of this technique greatly increases the relative measurement noise. To compensate for this issue, we introduce the use of optical pulse compression using perfect periodic correlation phase codes to increase the measurement signal-to-noise ratio and also to facilitate the simultaneous compensation of Rayleigh and polarization fading. In addition, we apply a method to further reduce the relative noise that is added to the two-wavelength measurement by using the synthetic wavelength measurement to unwrap the differential phase measured with a single wavelength. All this is highlighted in a 1-km sensing link in which up to 20-cm spatial resolution and 12.6 pϵ/√Hz strain sensitivity are demonstrated as well as a 67-fold enhancement in measurement range compared with the use of the conventional single-wavelength method., Agencia Estatal de Investigación (PID2019-107270RB-C22)
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Effect of linewidth on the relative intensity noise in random distributed feedback raman fiber lasers

  • Rota Rodrigo, Sergio
  • Leandro González, Daniel
  • Santarelli, Giorgio
  • López-Amo Sáinz, Manuel
  • Ania-Castañón, Juan Diego
We experimentally explore the relation between spectral linewidth and RIN transfer in half-open cavity random distributed feedback Raman lasers, demonstrating for the first time the possibility of adjusting the pump-to-signal RIN transfer intensity and cut-off frequency by using spectral filtering in the reflector section. We apply this approach to a 50-km laser system, operating in the C-Band, reliant on a standard single-mode fiber. We obtained a minimum bandwidth of 13 pm, which translates into a visible RIN cut-off at 800 MHz., This research was funded by the Spanish Government grants RTI2018-097957-B-C33, PID2021-128000OB-C21, and PID2019-107270RB-C22; Conseil Régional d’Aquitaine (2017-1R50302-00013493); LAPHIA (Lasers and Photonics in Aquitaine); the Horizon 2020 Framework Programme (H2020) (Marie Sklodowska-Curie—748839); and Comunidad de Madrid project SINFOTON2-CM (S2018-NMT/4326). Additional support was from AEI/FEDER funds.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Measurement of paracetamol concentration using an erbium-doped fiber ring cavity

  • Soares, Liliana
  • Pérez Herrera, Rosa Ana
  • Novais, Susana
  • Ferreira, António
  • Silva, Susana
  • Frazão, Orlando
Process Analytical Technology (PAT) has been increasingly used in the pharmaceutical industry to monitor essential parameters in real-time during pharmaceutical processes. The concentration of Active Pharmaceutical Ingredients (APIs), such as paracetamol, is one of these parameters, and controlling its variations allows for optimization of the production process. In this study, a refractometric sensor, implemented by an interrogation system based on an Erbium-Doped Fiber Ring Cavity (EDFRC), was presented and experimentally demonstrated. The Cavity Ring proposed included a 1 × 3 coupler. One port of the coupler was used to increase the optical power of the system through a Fiber Bragg Grating (FBG), and the other two ports were used as sensing head and reference. The sensor detected variations of paracetamol concentration with a sensitivity of [(−1.00 ± 0.05) × 10−3] nW/(g/kg) and a resolution of 5.53 g/kg. The results demonstrate the potential of this technology as a possible non-invasive PAT tool., and European Union “Next generation EU”/PTR. Liliana Soares acknowledges the support of FCT, Portugal, through the Grant 2020.05297.BD.This research was funded by: National Funds through the Portuguese funding agency, FCT—Fundação para a Ciência e a Tecnologia, within project UIDB/50014/2020; National Funds through FCT/MCTES (PIDDAC), within projects LA/P/0045/2020 (ALiCE), UIDB/00511/2020, and UIDP/00511/2020 (LEPABE); Program “José Castillejo para estancias de movilidad en el extranjero de jóvenes doctores”, funded by the Ministerio de Univesidades of Spain (reference CAS21/00351); project PID2019-107270RB-C22, funded by MCIN/AEI/10.13039/501100011033 and FEDER “A way to make Europe”; projects PDC2021-121172-C21 and TED2021-130378B-C22, funded by MCIN/AEI/10.13039/501100011033