Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 13
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Light-assistance in nitrogen fixation to ammonia by highly dispersed Cs-promoted Ru clusters supported on ZrO2

  • Yong, Peng
  • Shi, Run
  • Antonio Franconetti
  • Melillo, Arianna
  • Forneli Rubio, Mª Amparo
  • Albero-Sancho, Josep|||0000-0002-4841-7206
  • García Gómez, Hermenegildo|||0000-0002-9664-493X
[EN] Light-assisted N-2 fixation to NH3 under mild conditions is attracting massive attention to circumvent energy crisis and global warming. Herein, highly dispersed Cs-decorated Ru sub-nanometric clusters supported on ZrO2 NPs have been prepared by means of MOF-templated transformation method. The obtained catalyst exhibited N-2 hydrogenation activity of 1.6 mmolNH3 g(cat)(-1) h (-1) in the dark (350.C, 0.1 MPa). Remarkably this value increased by over 300 %, reaching 5.1 mmolNH3 g(cat)(-1) h (-1) (204 mmolNH3 g(Ru)(-1) h (-1)) under 1 Sun power illumination (1080 W/ m2) The influence of the incident light wavelength has been evaluated, revealing 81 % and 213 % enhancement in the NIR and visible region, respectively. DFT calculations were carried out to understand the static adsorption states of Ru sub-nanoclusters. Mechanistic studies have confirmed the co-existence of a photothermal and a nonthermal-hot electron mechanism. XPS, PXRD and FTIR analysis have determined that the Cs species block surface Zr4+ acidity, increasing the basicity of the ZrO2 support. Moreover, partially reduced Cs delta+ (0 <delta < 1) species surrounding the Ru active sites are donating electron density to the adjacent Ru sites, favoring N-2 adsorption and subsequent activation. Finally, this photocatalyst has shown an extended stability for 100 h irradiation under continuous flow., Financial support by the Spanish Ministry of Science and Innovation (PDI2021-126071-OB-C21 financed support by MCIN/AEI/10.13039/ 501100011033 and by FEDER "Una manera de hacer Europa"), and Severo Ochoa (CEX2021-1230-S financed support by MCIN/AEI/ 10.13039/501100011033) is gratefully acknowledged. Generalitat Valenciana (Prometeu 2021-038 and MFA-2022-023 financed by European Union-Next Generation EU, through the Conselleria de Innovacion, Universidades, Ciencia y Sociedad Digital) and European Union Horizon 2020 Research and Innovation Programme (Flow-PhotoChem Grant Agreement 862453) are also gratefully acknowledged. J.A. thanks the Spanish Ministry of Science and Innovation for a Ramon y Cajal research associate contract (RYC2021-031006-I financed support by MCIN/AEI/10.13039/501100011033 and by European Union/NextGenerationEU/ PRTR).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Visible and NIR Light Assistance of the N2 Reduction to NH3 Catalyzed by Cs-promoted Ru Nanoparticles Supported on Strontium Titanate

  • Peng, Yong
  • Franconetti, Antonio
  • Albero-Sancho, Josep|||0000-0002-4841-7206
  • Concepción Heydorn, Patricia|||0000-0003-2058-3103
  • García Gómez, Hermenegildo|||0000-0002-9664-493X
[EN] NH3 production accounts for more than 1% of the total CO2 emissions and is considered one of the most energy-intensive industrial processes currently (T > 400 degrees C and P > 80 bars). The development of atmospheric-pressure N2 fixation to NH3 under mild conditions is attracting much attention, especially using additional renewable energy sources. Herein, efficient photothermal NH3 evolution in continuous flow upon visible and NIR light irradiation at near 1 Sun power using Cs-decorated strontium titanate-supported Ru nanoparticles is reported. Notably, for the optimal photocatalytic composition, a constant NH3 rate near 3500 mu molNH3 gcatalyst-1 h-1 was achieved for 120 h reactions, being among the highest values reported at atmospheric pressure under 1 Sun irradiation., Financial support by the Spanish Ministry of Science and Innovation (Severo Ochoa and RTI2018-98237-CO2-1), Generalitat Valenciana (Prometeo 2017-083), and European Union's Horizon 2020 research and innovation programme under grant agreement no. 862453 is gratefully acknowledged.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Solving the Conundrum of the Influence of Irradiation Power on Photothermal CO&lt, sub&gt, 2&lt, /sub&gt, Hydrogenation

  • Szalad, Horatiu
  • Peng, Yong
  • Gosch, Jonas Werner
  • Baldi, Andrea
  • Askes, Sven H. C.
  • Albero-Sancho, Josep|||0000-0002-4841-7206
  • García Gómez, Hermenegildo|||0000-0002-9664-493X
[EN] Solar photocatalysis appears as a viable approach for the production of value-added chemicals from CO2. However, up to now, there is no information on the influence of the light intensity on the product distribution of CO2 hydrogenation and the modeling of the actual local temperature at the catalytic sites for typical nanoparticulate photocatalysts. Herein, it is shown that for a photothermal catalyst containing a high density of homogeneously distributed Ru nanoparticles, the collective heating prevails, resulting in a homogeneous temperature distribution in the material that should be relatively close to that of the support and that can be measured macroscopically. Moreover, light intensity has a clear influence on product distribution due to the differences in the local temperature, and therefore, attention should be paid to stable operating conditions, temperature, and CO2 conversion that can result in remarkable differences in product selectivity for the same catalyst as a function of light intensity., Financial support by the Spanish Ministry of Science and Innovation (CEX-2021-001230-S and PDI2021-0126071-OB- CO21 funded by MCIN/AEI/10.13039/501100011033), Generalitat Valenciana (Prometeo 2021/038 and Advanced Materials programme Graphica MFA/2022/023 with funding from European Union Next GenerationEU PRTR-C17.I1), and European Comission (Flow Photo Chem; Grant Agreement 86253) are gratefully acknowledged. J.A. thanks the Spanish Ministry of Science and Innovation by a Ramon y Cajal research associate contract (RYC2021-031006-I funded by MCIN/AEI/10.13039/501100011033 and by "European Union Next Generation EU/PRTR), and the financial support (PID2022-141099OA-I00 funded by MCIN/AEI/10.13039/501100011033 and by "European Union Next Generation EU/PRTR). S.H.C. Askes gratefully acknowledges the Dutch Research Council (NWO) for the NWO-XS grant (OCENW.XS21.4.167). A.B. gratefully acknowledges the Dutch Research Council (NWO) for the Vidi 680-47-550 grant.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Turning Carbon Dioxide and Ethane into Ethanol by Solar-Driven Heterogeneous Photocatalysis over RuO2- and NiO-co-Doped SrTiO3

  • Paulista, Larissa O.
  • Martins, Ramiro J. E.
  • Boaventura, Rui A. R.
  • Vilar, Vítor J. P.
  • Silva, Tania F. C. V.
  • Albero-Sancho, Josep|||0000-0002-4841-7206
  • García Gómez, Hermenegildo|||0000-0002-9664-493X
[EN] The current work focused on the sunlight-driven thermo-photocatalytic reduction of carbon dioxide (CO2), the primary greenhouse gas, by ethane (C2H6), the second most abundant element in shale gas, aiming at the generation of ethanol (EtOH), a renewable fuel. To promote this process, a hybrid catalyst was prepared and properly characterized, comprising of strontium titanate (SrTiO3) co-doped with ruthenium oxide (RuO2) and nickel oxide (NiO). The photocatalytic activity towards EtOH production was assessed in batch-mode and at gas-phase, under the influence of different conditions: (i) dopant loading; (ii) temperature; (iii) optical radiation wavelength; (vi) consecutive uses; and (v) electron scavenger addition. From the results here obtained, it was found that: (i) the functionalization of the SrTiO3 with RuO2 and NiO allows the visible light harvest and narrows the band gap energy (ca. 14-20%); (ii) the selectivity towards EtOH depends on the presence of Ni and irradiation; (iii) the catalyst photoresponse is mainly due to the visible photons; (iv) the photocatalyst loses > 50% efficiency right after the 2nd use; (v) the reaction mechanism is based on the photogenerated electron-hole pair charge separation; and (vi) a maximum yield of 64 mu mol EtOH g(cat)(-1) was obtained after 45-min (85 mu mol EtOH g(cat)(-1) h(-1)) of simulated solar irradiation (1000 W m(-2)) at 200 degrees C, using 0.4 g L-1 of SrTiO3:RuO2:NiO (0.8 wt.% Ru) with [CO2]:[C2H6] and [Ru]:[Ni] molar ratios of 1:3 and 1:1, respectively. Notwithstanding, despite its exploratory nature, this study offers an alternative route to solar fuels' synthesis from the underutilized C2H6 and CO2., This work was financially supported by the Base Funding-UIDB/50020/2020 of the Associate Laboratory LSRE-LCM-funded by national funds through FCT/MCTES (PIDDAC). Larissa O. Paulista also wants to acknowledge for her doctoral fellowship (reference SFRH/BD/137639/2018), supported by FCT. Tania F. C. V. Silva and Vitor J. P. Vilar acknowledge the FCT Individual Call to Scientific Employment Stimulus 2017 (CEECIND/01386/2017 and CEECIND/01317/2017, respectively). Josep Albero and Hermenegildo Garcia are also grateful to the Spanish Ministry of Science and Innovation (RTI2018-098237-CO2-R1 and Severo Ochoa), Generalitat Valencia (Prometeo 2017/083) and European Union's Horizon 2020 research and innovation programme under grant agreement No 862453, project FlowPhotochem, by financial contribution.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Co-doped hydroxyapatite as photothermal catalyst for selective CO2 hydrogenation

  • Peng, Yong
  • Szalad, Horatiu
  • Nikacevic, Pavle
  • Gorni, Giulio
  • Simonelli, Laura
  • López, Núria
  • Goberna-Ferrón, Sara|||0000-0002-3306-3791
  • Albero-Sancho, Josep|||0000-0002-4841-7206
  • García Gómez, Hermenegildo|||0000-0002-9664-493X
[EN] The rational design and in deep understanding of efficient, affordable and stable materials to promote the light-assisted production of fuels and commodity chemicals is very appealing for energy crisis and climate change amelioration. Herein, we have prepared a series of Co-doped hydroxyapatite (HAP) catalysts with different Co content. The materials structure has been widely investigated by XRD, FT-IR, HRTEM, XPS, XAS, as well as computational simulations based on Density Functional Theory (DFT) with PBE functional. At low Co loading, there is a partial substitution of Ca cations in the HAP structure, while higher loadings promote the precipitation of small (similar to 2 nm) Co nanoparticles on the HAP surface. For the optimal Co content, a constant CO rate of 62 mmol center dot g(-1)center dot h(-1) at 1 sun illumination and 400 degrees C, with the material being stable for 90 h. Visible and NIR photons have been determined responsible of the light-assisted activity enhanced. Mechanistic studies based on both experimental and DFT simulations show that H-2 preferentially adsorbs to metallic Co, while CO2 adsorbs to the HAP surface oxygen. Moreover, both direct photo- and plasmon-driven contributions have been separated in order to study their mechanisms independently., Financial support by European Comission (FlowPhotoChem Grant Agreement 862453 and Solar2Chem grant agreement 861151), The Spanish Ministry of Science and Innovation (Severo Ochoa CEX2021-1230-S financed by MCIN/AEI/10.13039/501100011033, PDI2021-126071-OB-C21 financed by MCIN/AEI/10.13039/501100011033 and by FEDER "Una manera de hacer Europa", and PLEC2021-7831 financed by MCIN/AEI/10.13039/501100011033 and by European Union Next-Generation EU/PRTR), and Generalitat Valenciana (Prometeu 2021-038 and MFA-2022-023 financed by European Union-Next Generation EU, through the Conselleria de Innovacion, Universidades, Ciencia y Sociedad Digital) are gratefully acknowledged. J. A. thanks the Spanish Ministry of Science and Innovation for a Ramon y Cajal research associate contract (RYC2021-031006-I) financed by MCIN/AEI/10.13039/501100011033 and by European Union/Next Generation EU/PRTR). P. N. and N. L. thank the Spanish Ministry of Science and Innovation for financial support PID2021-122515OB-I00, and Severo Ochoa Grant MCIN/AEI/10.13039/501100011033 CEX2019-000925-S) and Barcelona Supercomputing Center-MareNostrum (BSC-RES) for providing generaous computational resources.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Fe-Incorporated Co3O4 Microsheets for Oxygen Evolution at High Current Densities in All-Platinum-Group-Metal-Free Alkaline Anion Exchange Membrane Electrolyzers

  • Besic, Hanka
  • Tong, Wenming
  • Frish, Marvin L.
  • Thanh, Trung Ngo
  • Dionigi, Fabio
  • Klingenhof, Malte
  • Serban, Ariana
  • Twamley, Brendan
  • Strasser, Peter
  • Farras, Pau
  • Albero-Sancho, Josep|||0000-0002-4841-7206
[EN] The development of active, durable, and earth-abundant electrocatalysts for the oxygen evolution reaction (OER) remains a key challenge, as the catalysis at the anode accounts for major voltage losses in anion-exchange membrane water electrolyzers (AEMWE), particularly during operations at high current densities. Addressing this, Co3O4 emerges as a promising electrocatalyst, with its spinel structure allowing substitutions of cobalt with various transition metals to create more catalytically active sites and improve OER activities. In addition, advances in wet-chemistry synthesis allow careful control over the fabrication of the morphology of Co3O4 to achieve enhanced catalytic properties. This work presents Fe-incorporated Co3O4 with unique perforated sheet morphology as OER electrocatalysts. Even a minute amount of Fe in Co3O4 significantly improves the electrocatalytic activity, with an optimum Fe content at similar to 4.7%. An all-platinum-group-metal-free (PGM-free) alkaline AEMWE with Fe-incorporated Co3O4 as the anode catalyst reaches a competitive current density of 1 A<middle dot>cm-2 at 1.95 Vcell, with a promising degradation rate of 0.4 mV<middle dot>h-1 after the initial deteriorations, primarily associated with the degradation of membranes and ionomer/binders. The PGM-free electrolyzer further demonstrates great potential for operation at a higher current density of 2 A<middle dot>cm-2 at 2.06 Vcell., This work received funding from the European Union Horizon 2020 FlowPhotoChem project (Grant agreement number 862453) and was partially funded by the European Union's Horizon Europe research and innovation programme ANEMEL project (Grant agreement number 101071111). P.S. acknowledges partial funding from the German Ministry of Science and Education (BMBF) via the project AEM-Direkt (Forderkennzeichen 03HY130). J.A. thanks the Spanish Ministry of Science and Innovation (PID2022-141099OA-I00, funded by MCIN/AEI/10.13039/501100011033 and FEDER "Una manera de hacer Europa"). H.B., P.F., and W.T. acknowledge the scientific and technical assistance of Dr. Eadaoin Timmins in the use of the SEM and TEM within the Centre for Microscopy & Imaging, funded by the University of Galway and the Irish Government's Programme for Research in Third Level Institutions, Cycles 4 and 5, National Development Plan 2007-2013. The authors sincerely thank Prof. Xile Hu for his help in facilitating access to XPS.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Experimental investigation of photo-thermal catalytic reactor for the reverse water gas shift reaction under concentrated irradiation

  • Brust, David
  • Wullenkord, Michael
  • Sattler, Christian
  • García Gómez, Hermenegildo|||0000-0002-9664-493X
  • Albero-Sancho, Josep|||0000-0002-4841-7206
[EN] An upscaled photo-thermal catalytic reactor for the heterogeneously catalysed reverse Water Gas Shift (rWGS) reaction is tested under simulated concentrated irradiation. The reactor is equipped with an aperture of 144 cm2 area covered by a quartz window, where it receives irradiation flux densities of up to 80 kW/m2 corresponding to an irradiation power input of 1 kW thereby directly irradiating a RuO2 based photo-thermal catalyst that is deposited on a porous support. The system was operated under simulated concentrated sunlight for a total of 45.5 h with 35.4 h of chemical operation. A peak CO production rate of 1.6 mol/h was achieved with an average light concentration factor of 80 in the centre of the catalyst layer. This corresponds to a solar-to-chemical efficiency - defined by the ratio of the product of molar CO production rate and reaction enthalpy for the rWGS reaction and the irradiation power input - of 1.69 %. A calculation approach to determine the catalyst surface temperature under irradiation was introduced and utilised for performance analysis leading to the discussion of design modifications and operating strategies towards performance enhancement., The authors would like to thank the DLR team for their support and for the realisation of optics (C. Willsch, G. Dibowski) and test setup (M. Kloft, C. Spenke) and data acquisition and control (K. E ss er, F. Pierno) . Also, the authors acknowledge funding from the European Union's Horizon 2020 Research and Innovation Programme under grant agreement No 862453. The material presented and views expressed here are the responsibility of the authors only. The EU Commission takes no responsibility for any use made of the information set out.The help on part of PCM-OTP CNRS PROMES in performing the optothermal spectral measurements (C. Escape) is appreciated. This work was supported by the French "Investments for the future" programme managed by the National Agency for Research under contract ANR-10- EQPX-49-SOCRATE.J.A. thanks the Spanish Ministry of Science and Innovation for the Ramon y Cajal research associate contract (RYC2021-031006-I financed support by MCIN/AEI/10.13039/501100011033 and by European Union/NextGenerationEU/PRTR) and the financial support (PID2022-141099OA-I00 funded by MCIN/AEI/10.13039/501100011033 and FEDER "Una manera de hacer Europa".
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Activation of Self-Assembled CaWO4 Nanocrystals via Mn-Incorporation toward Nonenzymatic Electrocatalytic Glucose Oxidation

  • Nagy, Levente Alex
  • Besic, Hanka
  • Martinez-Belmonte, Marta
  • Tamayo, Borja Khatabi Soliman
  • Tong, Wenming
  • Farras, Pau
  • Albero-Sancho, Josep|||0000-0002-4841-7206
[EN] Integrating foreign metal ions into mixed metal oxide scaffolds, such as CaWO4, by a wet chemistry coprecipitation method is an efficient approach for regulating the chemical composition, which determines the structure and properties and, in turn, offers a versatile platform for enhancements of intrinsic properties and introduction of additional attributes in the host material. In this work, a series of Ca1-x Mn x WO4 was prepared via a coprecipitation process at 30 degrees C to exhibit sphere-like hierarchical structures assembled from individual nanocrystals. The solid solubility limit of Mn in CaWO4 is estimated to be similar to 24% for this synthetic approach. The nanocrystals exhibit nonstoichiometric amorphous layers on the surface, which are expected for this type of materials synthesized under such mild conditions. The successful incorporation of Mn into the crystal lattice of CaWO4 led to an isotropic contraction of the crystal unit cells as well as the shifting and merging of several vibrational modes. Cyclic voltammetry confirmed the activity of Ca1-x Mn x WO4 for the electrooxidation of glucose, which is directly linked to the presence of Mn in CaWO4. With the highest Mn content, Ca0.759Mn0.241WO4 achieved sensitivities of 3.80 and 1.00 mu A<middle dot>mM-1<middle dot>cm-2 for glucose concentrations in the ranges of 0.002-0.2 and 0.2-1 mM, respectively, which are 237 and 60 times increases from that of CaWO4. The limit of detection and lower limit of quantitation were estimated to be 14 and 48 mu M, respectively, with reasonable reproducibility and repeatability., This work received funding from the European Union Horizon 2020 FlowPhotoChem project (Grant agreement number 862453) and was partially funded by INTERREG Atlantic Area programme SEAFUEL project (Grant reference EAPA_190_2016). L.A.N. thanks the support from postgraduate scholarship by Taighde Eireann - Research Ireland under Grant number GOIPG/2021/1116. J.A. acknowledges financial support from the Spanish Ministry of Innovation and Science (Severo Ochoa CEX2021-001230-S funded by MCIN/AEI/10.13039/501100011033). L.A.N., H.B., P.F., and W.T. acknowledge the scientific and technical assistance of Dr. Eadaoin Timmins in the use of the SEM and TEM within the Centre for Microscopy & Imaging funded by University of Galway and the Irish Government's Programme for Research in Third Level Institutions, Cycles 4 and 5, National Development Plan 2007-2013.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Turning carbon dioxide and ethane into ethanol by solar-driven heterogeneous photocatalysis over ruo2-and nio-co-doped srtio3

  • Paulista, L.O.
  • Albero, J.
  • Martins, R.J.E.
  • Boaventura, R.A.R.
  • Vilar, V.J.P.
  • Silva, T.F.C.V.
  • García Gómez, Hermenegildo
The current work focused on the sunlight-driven thermo-photocatalytic reduction of carbon dioxide (CO), the primary greenhouse gas, by ethane (C H), the second most abundant element in shale gas, aiming at the generation of ethanol (EtOH), a renewable fuel. To promote this process, a hybrid catalyst was prepared and properly characterized, comprising of strontium titanate (SrTiO) co-doped with ruthenium oxide (RuO) and nickel oxide (NiO). The photocatalytic activity towards EtOH production was assessed in batch-mode and at gas-phase, under the influence of different conditions: (i) dopant loading; (ii) temperature; (iii) optical radiation wavelength; (vi) consecutive uses; and (v) electron scavenger addition. From the results here obtained, it was found that: (i) the functionalization of the SrTiO with RuO and NiO allows the visible light harvest and narrows the band gap energy (ca. 14–20%); (ii) the selectivity towards EtOH depends on the presence of Ni and irradiation; (iii) the catalyst photoresponse is mainly due to the visible photons; (iv) the photocatalyst loses > 50% efficiency right after the 2nd use; (v) the reaction mechanism is based on the photogenerated electron-hole pair charge separation; and (vi) a maximum yield of 64 µmol EtOH g was obtained after 45-min (85 µmol EtOH g h) of simulated solar irradiation (1000 W m) at 200 C, using 0.4 g L of SrTiO:RuO:NiO (0.8 wt.% Ru) with [CO ]:[C H ] and [Ru]:[Ni] molar ratios of 1:3 and 1:1, respectively. Notwithstanding, despite its exploratory nature, this study offers an alternative route to solar fuels’ synthesis from the underutilized C H and CO., This work was financially supported by the Base Funding—UIDB/50020/2020 of the Associate Laboratory LSRE-LCM—funded by national funds through FCT/MCTES (PIDDAC). Larissa O. Paulista also wants to acknowledge for her doctoral fellowship (reference SFRH/BD/137639/2018), supported by FCT. Tânia F. C. V. Silva and Vítor J. P. Vilar acknowledge the FCT Individual Call to Scientific Employment Stimulus 2017 (CEECIND/01386/2017 and CEECIND/01317/2017, respectively). Josep Albero and Hermenegildo García are also grateful to the Spanish Ministry of Science and Innovation (RTI2018-098237-CO2-R1 and Severo Ochoa), Generalitat Valencia (Prometeo 2017/083) and European Union’s Horizon 2020 research and innovation programme under grant agreement No 862453, project FlowPhotochem, by financial contribution.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Visible and NIR Light Assistance of the N2Reduction to NH3Catalyzed by Cs-promoted Ru Nanoparticles Supported on Strontium Titanate

  • Peng, Y.
  • Albero, J.
  • Franconetti, Antonio
  • Concepción, Patricia
  • García Gómez, Hermenegildo
NHproduction accounts for more than 1% of the total COemissions and is considered one of the most energy-intensive industrial processes currently (T > 400 °C and P > 80 bars). The development of atmospheric-pressure Nfixation to NHunder mild conditions is attracting much attention, especially using additional renewable energy sources. Herein, efficient photothermal NHevolution in continuous flow upon visible and NIR light irradiation at near 1 Sun power using Cs-decorated strontium titanate-supported Ru nanoparticles is reported. Notably, for the optimal photocatalytic composition, a constant NHrate near 3500 μmolghwas achieved for 120 h reactions, being among the highest values reported at atmospheric pressure under 1 Sun irradiation., Financial support by the Spanish Ministry of Science and Innovation (Severo Ochoa and RTI2018-98237-CO2-1), Generalitat Valenciana (Prometeo 2017-083), and European Union’s Horizon 2020 research and innovation programme under grant agreement no. 862453 is gratefully acknowledged.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Co-doped hydroxyapatite as photothermal catalyst for selective CO2 hydrogenation

  • Peng, Yong
  • Szalad, Horatiu
  • Nikacevic, Pavle
  • Gorni, Giulio
  • Goberna-Ferrón, Sara
  • Simonelli, Laura
  • Albero, J.
  • López, Nuria
  • García Gómez, Hermenegildo
The rational design and in deep understanding of efficient, affordable and stable materials to promote the light-assisted production of fuels and commodity chemicals is very appealing for energy crisis and climate change amelioration. Herein, we have prepared a series of Co-doped hydroxyapatite (HAP) catalysts with different Co content. The materials structure has been widely investigated by XRD, FT-IR, HRTEM, XPS, XAS, as well as computational simulations based on Density Functional Theory (DFT) with PBE functional. At low Co loading, there is a partial substitution of Ca cations in the HAP structure, while higher loadings promote the precipitation of small (∼ 2 nm) Co nanoparticles on the HAP surface. For the optimal Co content, a constant CO rate of 62 mmol·g·h at 1 sun illumination and 400 °C, with the material being stable for 90 h. Visible and NIR photons have been determined responsible of the light-assisted activity enhanced. Mechanistic studies based on both experimental and DFT simulations show that H preferentially adsorbs to metallic Co, while CO adsorbs to the HAP surface oxygen. Moreover, both direct photo- and plasmon-driven contributions have been separated in order to study their mechanisms independently., Financial support by European Comission (FlowPhotoChem Grant Agreement 862453 and Solar2Chem grant agreement 861151), The Spanish Ministry of Science and Innovation (Severo Ochoa CEX2021-1230-S financed by MCIN/AEI/10.13039/501100011033, PDI2021-126071-OB-C21 financed by MCIN/AEI/10.13039/501100011033 and by FEDER "Una manera de hacer Europa", and PLEC2021-7831 financed by MCIN/AEI/10.13039/501100011033 and by European Union NextGenerationEU/PRTR), and Generalitat Valenciana (Prometeu 2021-038 and MFA-2022-023 financed by European Union-Next Generation EU, through the Conselleria de Innovación, Universidades, Ciencia y Sociedad Digital) are gratefully acknowledged. J. A. thanks the Spanish Ministry of Science and Innovation for a Ramon y Cajal research associate contract (RYC2021-031006-I) financed by MCIN/AEI/10.13039/501100011033 and by European Union/NextGenerationEU/ PRTR). P. N. and N. L. thank the Spanish Ministry of Science and Innovation for financial support PID2021-122515OB-I00, and Severo Ochoa Grant MCIN/AEI/10.13039/501100011033 CEX2019-000925-S) and Barcelona Supercomputing Center-MareNostrum (BSC-RES) for providing generaous computational resources., With funding from the Spanish government through the ‘Severo Ochoa Centre of Excellence’ accreditation (CEX2021-1230-S)., With funding from the Spanish government through the ‘Severo Ochoa Centre of Excellence’ accreditation (CEX2019-000925-S)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Light-assistance in nitrogen fixation to ammonia by highly dispersed Cs-promoted Ru clusters supported on ZrO2

  • Peng, Y.
  • Melillo, A.
  • Shi, Run
  • Forneli, Amparo
  • Franconetti, Antonio
  • Albero, J.
  • García Gómez, Hermenegildo
Light-assisted N fixation to NH under mild conditions is attracting massive attention to circumvent energy crisis and global warming. Herein, highly dispersed Cs-decorated Ru sub-nanometric clusters supported on ZrO NPs have been prepared by means of MOF-templated transformation method. The obtained catalyst exhibited N hydrogenation activity of 1.6 mmol g h in the dark (350 °C, 0.1 MPa). Remarkably this value increased by over 300 %, reaching 5.1 mmol g h (204 mmol g h) under 1 Sun power illumination (1080 W/m) The influence of the incident light wavelength has been evaluated, revealing 81 % and 213 % enhancement in the NIR and visible region, respectively. DFT calculations were carried out to understand the static adsorption states of Ru sub-nanoclusters. Mechanistic studies have confirmed the co-existence of a photothermal and a nonthermal-hot electron mechanism. XPS, PXRD and FTIR analysis have determined that the Cs species block surface Zr acidity, increasing the basicity of the ZrO support. Moreover, partially reduced Cs (0 <δ < 1) species surrounding the Ru active sites are donating electron density to the adjacent Ru sites, favoring N adsorption and subsequent activation. Finally, this photocatalyst has shown an extended stability for 100 h irradiation under continuous flow., Financial support by the Spanish Ministry of Science and Innovation (PDI2021–126071-OB-C21 financed support by MCIN/AEI/10.13039/501100011033 and by FEDER "Una manera de hacer Europa"), and Severo Ochoa (CEX2021–1230-S financed support by MCIN/AEI/10.13039/501100011033) is gratefully acknowledged. Generalitat Valenciana (Prometeu 2021–038 and MFA-2022–023 financed by European Union-Next Generation EU, through the Conselleria de Innovación, Universidades, Ciencia y Sociedad Digital) and European Union Horizon 2020 Research and Innovation Programme (FlowPhotoChem Grant Agreement 862453) are also gratefully acknowledged. J.A. thanks the Spanish Ministry of Science and Innovation for a Ramon y Cajal research associate contract (RYC2021–031006-I financed support by MCIN/AEI/10.13039/501100011033 and by European Union/NextGenerationEU/ PRTR)., With funding from the Spanish government through the ‘Severo Ochoa Centre of Excellence’ accreditation (CEX2021–1230-S)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Experimental investigation of photo-thermal catalytic reactor for the reverse water gas shift reaction under concentrated irradiation

  • Brust, David
  • Wullenkord, Michael
  • García Gómez, Hermenegildo
  • Albero, J.
  • Sattler, Christian
An upscaled photo-thermal catalytic reactor for the heterogeneously catalysed reverse Water Gas Shift (rWGS) reaction is tested under simulated concentrated irradiation. The reactor is equipped with an aperture of 144 cm area covered by a quartz window, where it receives irradiation flux densities of up to 80 kW/m corresponding to an irradiation power input of 1 kW thereby directly irradiating a RuO based photo-thermal catalyst that is deposited on a porous support. The system was operated under simulated concentrated sunlight for a total of 45.5 h with 35.4 h of chemical operation. A peak CO production rate of 1.6 mol/h was achieved with an average light concentration factor of 80 in the centre of the catalyst layer. This corresponds to a solar-to-chemical efficiency – defined by the ratio of the product of molar CO production rate and reaction enthalpy for the rWGS reaction and the irradiation power input – of 1.69 %. A calculation approach to determine the catalyst surface temperature under irradiation was introduced and utilised for performance analysis leading to the discussion of design modifications and operating strategies towards performance enhancement., The authors would like to thank the DLR team for their support and for the realisation of optics (C. Willsch, G. Dibowski) and test setup (M. Kloft, C. Spenke) and data acquisition and control (K. Eßer, F. Pierno). Also, the authors acknowledge funding from the European Union’s Horizon 2020 Research and Innovation Programme under grant agreement No 862453. The material presented and views expressed here are the responsibility of the authors only. The EU Commission takes no responsibility for any use made of the information set out. The help on part of PCM-OTP CNRS PROMES in performing the opto-thermal spectral measurements (C. Escape) is appreciated. This work was supported by the French “Investments for the future” programme managed by the National Agency for Research under contract ANR-10-EQPX-49-SOCRATE. J.A. thanks the Spanish Ministry of Science and Innovation for the Ramon y Cajal research associate contract (RYC2021-031006-I financed support by MCIN/AEI/10.13039/501100011033 and by European Union/NextGenerationEU/ PRTR) and the financial support (PID2022–141099OA-I00 funded by MCIN/AEI/10.13039/501100011033 and FEDER "Una manera de hacer Europa".