Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 22
Encontrada(s) 1 página(s)

RUC. Repositorio da Universidade da Coruña
Publicación Artículo científico (JournalArticle)

Microstructural Evolution Dominates the Changes in the Thermal Conductivity of Conjugated Polymers Upon Doping

  • Guo, Jiali
  • Asatryan, Jesika
  • Martín, Jaime
  • Campoy-Quiles, Mariano
[Abstract]: In this study, the correlation between the changes in microstructure of conjugated polymers upon doping and their concomitant thermal transport properties is elucidated. Eight conjugated polymers across distinct doping systems are examined: molecular dopants, Lewis acid type dopants, and ion-exchange systems. These findings indicate that, upon doping, there is a decrease in out-of-plane thermal conductivity for five polymers characterized by high structural order, such as those based on thiophene, diketopyrrolopyrrole, and terthiophene-naphthalimide copolymers. Conversely, for polymers with less ordered structures, including regioregular poly(3-hexylthiophene) and thiophene-based polymers with oligoether side chains, an increase in out-of-plane thermal conductivity is observed. To elucidate these trends, several hypotheses are examined: i) enhanced intrinsic thermal anisotropy originating from backbone orientation, ii) variations in the crystalline to amorphous fraction, and (iii) alloying effects resulting from dopant incorporation. Grazing incidence wide-angle X-ray scattering reveals that in-plane alignment exerts a direct influence on both in-plane and out-of-plane thermal conductivities. Photooxidation experiments provide further insights into the role of alloy scattering. Ultimately, the in-plane thermoelectric figure of merit is ascertained for two diketopyrrolopyrrole-based polymers, underscoring the critical importance of measuring thermal and electrical properties in the same orientation to ensure precise thermoelectric evaluation., The authors acknowledge funding from the European Union’s Horizon 2020 research and innovation programme through the Marie Skłodowska-Curie grant agreement no. 955837 (HORATES). The authors acknowledge financial support from the Spanish Ministerio de Ciencia, Innovación y Universidades and the for its support through Grant CEX2023- in the framework of the Spanish Severo Ochoa Centre of Excellence, and Grants PID2021-128924OB-I00, PID2020-119777GBI00 (THERM2MAIN), PID2022-138908NB-C33, and PDC2021-121814- I00 (COVEQ). The authors also acknowledge Grant 2021-SGR-00444 (NANOPTO) from the Catalan agency AGAUR. The authors acknowledge Dr. Bernhard Dörling for support with thermoelectric measurements and Dr. Agustín Mihi as well as ICMAB-CSIC for access to and support with the FTIR equipment. This work has been carried out within the framework of the doctoral program in Material Science at the Universitat Autònoma de Barcelona in which J. G. was enrolled. The authors acknowledge support for the publication fee by the CSIC Open Access Publication Support Initiative through its Unit of Information Resources for Research (URICI)., Generalitat de Catalunya; 2021-SGR-00444
RUC. Repositorio da Universidade da Coruña
Publicación Artículo científico (JournalArticle)

Impact of Oligoether Side-Chain Length on the Thermoelectric Properties of a Polar Polythiophene

  • Asatryan, Jesika
  • Martín, Jaime
  • Müller, Christian
[Abstract]: Conjugated polymers with oligoether side chains make up a promising class of thermoelectric materials. In this work, the impact of the side-chain length on the thermoelectric and mechanical properties of polythiophenes is investigated. Polymers with tri-, tetra-, or hexaethylene glycol side chains are compared, and the shortest length is found to result in thin films with the highest degree of order upon doping with the p-dopant 2,3,5,6-tetrafluoro-7,7,8,8-tetracyanoquinodimethane (F4TCNQ). As a result, a stiff material with an electrical conductivity of up to 830 ± 15 S cm–1 is obtained, resulting in a thermoelectric power factor of about 21 μW m–1 K–2 in the case of as-cast films. Aging at ambient conditions results in an initial decrease in thermoelectric properties but then yields a highly stable performance for at least 3 months, with values of about 200 S cm–1 and 5 μW m–1 K–2. Evidently, identification of the optimal side-chain length is an important criterion for the design of conjugated polymers for organic thermoelectrics., Ministerio de Ciencia e Innovación; CEX2019-000917-S (FUNFUTURE), info:eu-repo/grantAgreement/AEI/ PROYECTOS I+D GENERACIÓN DEL CONOCIMIENTO Y RETOS INVESTIGACIÓN/PID2020-119777GBI00/ES/THERM2MAIN, info:eu-repo/grantAgreement/AEI/Plan Estatal de Investigación Científica y Técnica y de Innovación 2017-2020/PDC2021-121814-I00/ ES/EQUIPO COMPACTO/PORTATIL, ECONOMICO Y VERSATIL PARA LA CARACTERIZACION DE LAS PROPIEDADES TERMICAS DE MATERIALES, We acknowledge funding from the European Union’s Horizon 2020 research and innovation programme through the Marie Skłodowska-Curie grant agreement no. 955837 (HORATES) and the Knut and Alice Wallenberg Foundation through a Wallenberg Academy Fellowship Prolongation grant. We acknowledge financial support from the Spanish Ministerio de Ciencia e Innovacíon for its support through grant CEX2019-000917-S (FUNFUTURE) in the framework of the Spanish Severo Ochoa Centre of Excellence program, and grants PID2020-119777GBI00 (THERM2MAIN), and PDC2021-121814-I00 (COVEQ). K.X. acknowledges a fellowship (CSC201806950006) from China Scholarship Council. K.X. and J.G. thank the PhD programme in Materials Science from Universitat Autònoma de Barcelona in which they are enrolled. We thank Johanna Heimonen for help with SEC measurements and Anders Mårtensson for carrying out the AFM measurements. This project was in part performed at the Chalmers Materials Analysis Laboratory (CMAL).
RUC. Repositorio da Universidade da Coruña
Publicación Artículo científico (JournalArticle)

A Universal, Highly Stable Dopant System for Organic Semiconductors Based on Lewis-Paired Dopant Complexes

  • Zapata-Arteaga, Osnat
  • Perevedentsev, Aleksandr
  • Prete, Michela
  • Busato, Stephan
  • Floris, Paolo Sebastiano
  • Asatryan, Jesika
  • Rurali, Riccardo
  • Martín, Jaime
  • Campoy-Quiles, Mariano
[Abstract]: Chemical doping of organic semiconductors is an essential enabler for applications in electronic and energy-conversion devices such as thermoelectrics. Here, Lewis-paired complexes are advanced as high-performance dopants that address all the principal drawbacks of conventional dopants in terms of limited electrical conductivity, thermal stability, and generality. The study focuses on the Lewis acid B(C6F5)3 (BCF) and 2,3,5,6-tetrafluoro-7,7,8,8-tetracyanoquinodimethane (F4TCNQ) bearing Lewis-basic −CN groups. Due to its high electron affinity, BCF:F4TCNQ dopes an exceptionally wide range of organic semiconductors, over 20 of which are investigated. Complex activation and microstructure control lead to conductivities for poly(3-hexylthiophene) (P3HT) exceeding 300 and 900 S cm–1 for isotropic and chain-oriented films, respectively, resulting in a 10 to 50 times larger thermoelectric power factor compared to those obtained with neat dopants. Moreover, BCF:F4TCNQ-doped P3HT exhibits a 3-fold higher thermal dedoping activation energy compared to that obtained with neat dopants and at least a factor of 10 better operational stability., We thank Martin Kreuzer for extensive support and fruitful discussions at the Alba synchrotron BL01-MIRAS beamline. Jiali Guo and Dr. Edgar Gutierrez are also thanked for their support with the Alba experiments. We also thank Prof. Walter Caseri and Dr Marco D’Elia (Department of Materials, ETH Zürich) for generously contributing samples of poly(phenylene methylene)s as well as the many stimulating discussions. Dr Agustín Mihi (ICMAB-CSIC) is thanked for providing access to the Bruker IR spectrophotometry equipment. This work was financially supported by the European Commission through the Marie Skłodowska-Curie project HORATES (GA- 955837), by the Spanish Ministry of Science and Innovation (MCIN/AEI/10.13039/501100011033) under grants PID2020-119777GB-I00, PID2021-128924OB-I00 and the Severo Ochoa Centres of Excellence Program under grant CEX2019-000917-S (particularly, PALOMA grant within ICMAB’s ‘Frontier Interdisciplinary Projects’ (FIP-2021) Program), and by the Generalitat de Catalunya under grant no. 2017 SGR 1506. The work of PSF has been carried out within the PhD program in Physics of the Universitat Autònoma de Barcelona (UAB). We thank the Centro de Supercomputación de Galicia (CESGA) for the use of their computational resources., Generalitat de Catalunya; 2017-SGR-1506
RUC. Repositorio da Universidade da Coruña
Publicación Artículo científico (JournalArticle)

On The Thermal Conductivity of Conjugated Polymers for Thermoelectrics

  • Rodríguez-Martínez, Xabier
  • Martín, Jaime
  • Campoy-Quiles, Mariano
[Abstract]: The thermal conductivity (κ) governs how heat propagates in a material, and thus is a key parameter that constrains the lifetime of optoelectronic devices and the performance of thermoelectrics (TEs). In organic electronics, understanding what determines κ has been elusive and experimentally challenging. Here, by measuring κ in 17 π-conjugated materials over different spatial directions, it is statistically shown how microstructure unlocks two markedly different thermal transport regimes. κ in long-range ordered polymers follows standard thermal transport theories: improved ordering implies higher κ and increased anisotropy. κ increases with stiffer backbones, higher molecular weights and heavier repeat units. Therein, charge and thermal transport go hand-in-hand and can be decoupled solely via the film texture, as supported by molecular dynamics simulations. In largely amorphous polymers, however, κ correlates negatively with the persistence length and the mass of the repeat unit, and thus an anomalous, albeit useful, behavior is found. Importantly, it is shown that for quasi-amorphous co-polymers (e.g., IDT-BT) κ decreases with increasing charge mobility, yielding a 10-fold enhancement of the TE figure-of-merit ZT compared to semi-crystalline counterparts (under comparable electrical conductivities). Finally, specific material design rules for high and low κ in organic semiconductors are provided., The authors would like to acknowledge financial support from the Spanish Ministry of Science and Innovation through the “Severo Ochoa” Programme for Centers of Excellence in R&D and project reference PID2021- 128924OB-I00 as well acknowledge Prof. Alejandro R. Goñi (ICMAB-CSIC, ICREA) for his valuable help in setting up the Raman thermometry measurement platform. The authors are thankful to Dr. Aleksandr Perevedentsev (ICMAB-CSIC) for his know-how regarding the fabrication of free-standing films, as well as for the preparation of the drop cast DH6T films. The authors are very thankful to Prof. Paul Smith (ETH Zürich) for fruitful discussions about polymer processing and Prof. Christian Müller for his useful comments on this work, and the suggestions regarding thermal diffusivity. The authors also thank Andrés Gómez for performing the nanoindentation experiments. I.M. and H.C. acknowledge King Abdullah University of Science and Technology Office of Sponsored Research (OSR) under awards no. OSR-2018-CARF/CCF-3079, and OSR-4106 CPF2019 as well as EC FP7 Project SC2 (610115).as the European Research Council (ERC) under grant agreement no. 648901. This work was financially supported by the European Commission through the Marie Skłodowska-Curie projects HORATES (GA-955837). J.M. is also grateful to the Spanish Ministry of Science and Innovation through project PGC2018-094620-A-I00. The authors also acknowledge the support from the Marie Skłodowska-Curie program (action no. 793726 – TELIOTES) and the Centro de Supercomputación de Galicia (CESGA) for the use of their computational resources. The authors, Arabia Saudita. King Abdullah University of Science and Technology; OSR-2018-CARF/CCF-3079, Arabia Saudita. King Abdullah University of Science and Technology; OSR-4106 CPF2019
RUC. Repositorio da Universidade da Coruña
Publicación Artículo científico (JournalArticle)

High-Mobility Organic Mixed Conductors with a low Synthetic Complexity Index via Direct Arylation Polymerization

  • Kimpel, Joost
  • Kim, Youngseok
  • Asatryan, Jesika
  • Martín, Jaime
  • Kroon, Renee
  • Müller, Christian
[Abstract]: Through direct arylation polymerization, a series of mixed ion-electron conducting polymers with a low synthetic complexity index is synthesized. A thieno[3,2-b]thiophene monomer with oligoether side chains is used in direct arylation polymerization together with a wide range of aryl bromides with varying electronic character from electron-donating thiophene to electron-accepting benzothiadiazole. The obtained polymers are less synthetically complex than other mixed ion–electron conducting polymers due to higher yield, fewer synthetic steps and less toxic reagents. Organic electrochemical transistors (OECTs) based on a newly synthesized copolymer comprising thieno[3,2-b]thiophene with oligoether side chains and bithiophene exhibit excellent device performance. A high charge-carrier mobility of up to μ = 1.8 cm2 V−1 s−1 was observed, obtained by dividing the figure of merit [μC*] from OECT measurements by the volumetric capacitance C* from electrochemical impedance spectroscopy, which reached a value of more than 215 F cm−3., We acknowledge funding from the European Union's Horizon 2020 research and innovation programme through the Marie Skłodowska-Curie grant agreement no. 955837 (HORATES) and the Knut and Alice Wallenberg Foundation through a Wallenberg Scholar grant. J. M. thanks MICINN/FEDER for grant Ref. PID2021-126243NB-I00. We thank Lars ¨Ohrström for providing access to single X-ray crystallography, Ergang Wang for providing several commercially available monomers, Diego Ropero Hinojosa and Michael Sommer for providing access to high temperature NMR, as well as Rukiya Matsidik and Michael Sommer for performing MALDI-ToF measurements. DFT calculations were enabled by resources provided by Chalmers e- Commons. The project was in part performed at the Chalmers Materials Analysis Laboratory (CMAL).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

In-plane thermal diffusivity determination using beam-offset frequency-domain thermoreflectance with a one-dimensional optical heat source

  • Xu, Kai
  • Guo, Jiali
  • Raciti, Grazia
  • Goñi, Alejandro R.
  • Alonso Carmona, M. Isabel
  • Borrisé, Xavier
  • Zardo, Ilaria
  • Campoy Quiles, Mariano
  • Reparaz, J. Sebastian
We present an innovative contactless method suitable to study in-plane thermal transport based on beam-offset frequency-domain thermoreflectance using a one-dimensional heat source with uniform power distribution. Using a one-dimensional heat source provides a number of advantages as compared to point-like heat sources, as typically used in time- and frequency-domain thermoreflectance experiments, just to name a few: (i) it leads to a slower spatial decay of the temperature field in the direction perpendicular to the line-shaped heat source, allowing to probe the temperature field at larger distances from the heater, hence, enhancing the sensitivity to in-plane thermal transport; (ii) the frequency range of interest is typically kHz. This rather low frequency range is convenient regarding the cost of the required excitation laser system but, most importantly, it allows the study of materials without the presence of a metallic transducer with almost no influence of the finite optical penetration depth of the pump and probe beams on the thermal phase lag, which arises from the large thermal penetration depth imposed by the used frequency range. We also show that for the case of a harmonic thermal excitation source, the phase lag between the thermal excitation and thermal response of the sample exhibits a linear dependence with their spatial offset, where the slope is proportional to the inverse of the thermal diffusivity of the material. We demonstrate the applicability of this method to the cases of: (i) suspended thin films of Si and PDPP4T, (ii) Bi bulk samples, and (iii) Si, glass, and highly-oriented pyrollitic graphite (HOPG) bulk samples with a thin metallic transducer. Finally, we also show that it is possible to study in-plane heat transport on substrates with rather low thermal diffusivity, e.g., glass, even using a metallic transducer. We achieve this by an original approach based on patterning the transducer using focused ion beam, with the key purpose of limiting in-plane heat transport through the thin metallic transducer., We acknowledge financial support from the Spanish Ministerio de Economía, Industria y Competitividad for its support through grant CEX2019-000917-S (FUNFUTURE) in the framework of the Spanish Severo Ochoa Centre of Excellence program, and grants PID2020-119777GB-I00 (THERM2MAIN), and PDC2021-121814-I00 (COVEQ). This work was financially supported by the European Commission through the Marie Sklodowska-Curie project HORATES (GA-955837). We also acknowledge grant 2021-SGR-00444 (NANOPTO) from AGAUR. K.X. acknowledges a fellowship (CSC201806950006) from China Scholarship Council and the Ph.D. programme in Materials Science from Universitat Autónoma de Barcelona in which he was enrolled. G.R and I.Z. acknowledge financial support from Eucor, The European Campus (Marie Sklodowska-Curie QUSTEC grant agreement no. 847471) and the Swiss National Science Foundation (Project Grant no. CRSII5 189924 )., With funding from the Spanish government through the ‘Severo Ochoa Centre of Excellence’ accreditation (CEX2019-000917-S)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Interplay Between Doping, Morphology, and Lattice Thermal Conductivity in PEDOT:PSS

  • Floris, Paolo Sebastiano
  • Melis, Claudio
  • Rurali, Riccardo
Organic materials for thermoelectric (TE) applications have attracted a fair amount of attention in recent years due to remarkable advances achieved in terms of their figure of merit, ZT: a value of 0.42 has been reported by for poly(3,4-ethylenedioxythiophene) polystyrene sulfonate (PEDOT:PSS) films treated with dimethyl sulfoxide, while 0.25 has been obtained for PEDOT:Tosylate. In this study various PEDOT morphologies are investigated, considering both neutral and doped (bipolaronic) samples, by means of classical molecular dynamics, by taking advantage of a recently developed all-atom force field. In the case of bare PEDOT, it is found that changing the distribution of chain lengths affects the thermal conductivity of neutral and doped samples in a different way: longer chain lengths result in higher conductivities in the neutral scenario, whereas an intermediate chain length gives the highest value in the bipolaronic case. The role of PSS in the bipolaronic state, as compared to the simpler case where the counterion is Cl−, is discussed., This work was financially supported by the European Commission through the Marie Skłodowska–Curie projects HORATES (GA-955837), by MCIN/AEI/10.13039/501100011033 under grant PID2020-119777GB-I00, and the Severo Ochoa Centres of Excellence Program under grant CEX2019-000917-S, and by the Generalitat de Catalunya under grant no. and 2017 SGR 1506. We thank the Centro de Supercomputación de Galicia (CESGA) for the use of their computational resources. The authors would like to thank Wesley Micheals and Jian Qin for the insights provided about the force field employed in this work, Mariano Campoy-Quiles, Simone Fabiano, Christian Müller, Igor Zozoulenko for useful discussions. The author P.S.F. would like to extend his personal thanks to Marc Domingo Cabases for his advice on some of the technicalities involved in this research., With funding from the Spanish government through the ‘Severo Ochoa Centre of Excellence’ accreditation (CEX2019-000917-S)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Improved Performance of Organic Thermoelectric Generators Through Interfacial Energetics

  • Petsagkourakis, Ioannis
  • Riera Galindo, Sergi
  • Ruoko, Tero-Petri
  • Strakosas, X
  • Pavlopoulou, Eleni
  • Liu, X
  • Braun, S
  • Kroon, Renee
  • Kim, N
  • Lienemann, Samuel
  • Gueskine, V
  • Hadziioannou, G
  • Berggren, M
  • Fahlman, Mats
  • Fabiano, Simone
  • Tybrandt, Klas
  • Crispin, Xavier
The interfacial energetics are known to play a crucial role in organic diodes, transistors, and sensors. Designing the metal-organic interface has been a tool to optimize the performance of organic (opto)electronic devices, but this is not reported for organic thermoelectrics. In this work, it is demonstrated that the electrical power of organic thermoelectric generators (OTEGs) is also strongly dependent on the metal-organic interfacial energetics. Without changing the thermoelectric figure of merit (ZT) of polythiophene-based conducting polymers, the generated power of an OTEG can vary by three orders of magnitude simply by tuning the work function of the metal contact to reach above 1000 µW cm-2 . The effective Seebeck coefficient (Seff ) of a metal/polymer/metal single leg OTEG includes an interfacial contribution (Vinter /ΔT) in addition to the intrinsic bulk Seebeck coefficient of the polythiophenes, such that Seff  = S + Vinter /ΔT varies from 22.7 µV K-1 [9.4 µV K-1 ] with Al to 50.5 µV K-1 [26.3 µV K-1 ] with Pt for poly(3,4-ethylenedioxythiophene):p-toluenesulfonate [poly(3,4-ethylenedioxythiophene):poly(4-styrenesulfonate)]. Spectroscopic techniques are used to reveal a redox interfacial reaction affecting locally the doping level of the polymer at the vicinity of the metal-organic interface and conclude that the energetics at the metal-polymer interface provides a new strategy to enhance the performance of OTEGs., This work was financially supported by the Knut and Alice Wallenberg Foundation (Tail of the sun), the EU project (ESR 955837_HORATES), the Swedish Research Council (2016-06146, 2016–03979), ÅForsk (18-313), Academy of Finland Postdoctoral Researcher (Project Number 340103), EU H2020 Marie Sklodowska-Curie grant agreement (No 101022777), Swedish Foundation for Strategic Research (SiOS), and the Swedish Government Strategic Research Area in Materials Science on Advanced Functional Materials at Linköping University (Faculty Grant SFO-Mat-LiU No. 2009-00971). X-ray scattering experiments were performed at the NCD-SWEET beamline of ALBA synchrotron with the collaboration of ALBA staff and in particular of Dr. Eduardo Solano. The authors acknowledge Prof. I. Zozoulenko, Prof. M. P. Jonsson, Prof. E. Glowacki, Dr. M. Linares and Dr. H. Sun of LOE, Linköping University, Dr. Y. Xia at IFM, Linköping University, and Dr. S.M. Gali, University of Mons, for fruitful discussions. We also acknowledge Mr. L. Gustavsson, Mr. M. Karami Rad, and Mr. T. Karlsson for their technical assistance in realizing the environmental glovebox experiments and their outstanding support in technical issues with our characterization equipment, Dr. F. N. Ajjan Godoy for assistance in drawing of chemical molecules, Dr. H. Wiberg of Gränges for performing and analyzing the ICP-OES and Dr. L. Migliaccio and Dr. C.Diacci for their assistance in the initial glovebox experiments., With funding from the Spanish government through the ‘Severo Ochoa Centre of Excellence’ accreditation (CEX2019-000917-S)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Impact of Oligoether Side-Chain Length on the Thermoelectric Properties of a Polar Polythiophene

  • Craighero, Mariavittoria
  • Guo, Jiali
  • Zokaei, Sepideh
  • Griggs, Sophie
  • Tian, Junfu
  • Asatryan, Jesika
  • Kimpel, Joost
  • Kroon, Renee
  • Xu, Kai
  • Reparaz, J. Sebastian
  • Martin, Jaime
  • Mcculloch, Iain
  • Campoy Quiles, Mariano
  • Mueller, Christian
This article is part of the Advanced Thermoelectric Materials and Devices special issue., Conjugated polymers with oligoether side chains make up a promising class of thermoelectric materials. In this work, the impact of the side-chain length on the thermoelectric and mechanical properties of polythiophenes is investigated. Polymers with tri-, tetra-, or hexaethylene glycol side chains are compared, and the shortest length is found to result in thin films with the highest degree of order upon doping with the p-dopant 2,3,5,6-tetrafluoro-7,7,8,8-tetracyanoquinodimethane (F4TCNQ). As a result, a stiff material with an electrical conductivity of up to 830 ± 15 S cm–1 is obtained, resulting in a thermoelectric power factor of about 21 μW m–1 K–2 in the case of as-cast films. Aging at ambient conditions results in an initial decrease in thermoelectric properties but then yields a highly stable performance for at least 3 months, with values of about 200 S cm–1 and 5 μW m–1 K–2. Evidently, identification of the optimal side-chain length is an important criterion for the design of conjugated polymers for organic thermoelectrics., We acknowledge funding from the European Union’s Horizon 2020 research and innovation programme through the Marie Skłodowska-Curie grant agreement no. 955837 (HORATES) and the Knut and Alice Wallenberg Foundation through a Wallenberg Academy Fellowship Prolongation grant. We acknowledge financial support from the Spanish Ministerio de Ciencia e Innovacíon for its support through grant CEX2019-000917-S (FUNFUTURE) in the framework of the Spanish Severo Ochoa Centre of Excellence program, and grants PID2020-119777GBI00 (THERM2MAIN), and PDC2021-121814-I00 (COVEQ). K.X. acknowledges a fellowship (CSC201806950006) from China Scholarship Council. K.X. and J.G. thank the PhD programme in Materials Science from Universitat Autònoma de Barcelona in which they are enrolled. We thank Johanna Heimonen for help with SEC measurements and Anders Mårtensson for carrying out the AFM measurements. This project was in part performed at the Chalmers Materials Analysis Laboratory (CMAL)., With funding from the Spanish government through the ‘Severo Ochoa Centre of Excellence’ accreditation (CEX2019-000917-S)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Effects of vacancies on the thermal conductivity of Si nanowires

  • Túnica, Marc
  • Floris, Paolo Sebastiano
  • Torres, Pol
  • Rurali, Riccardo
Point defects can be used to tailor the properties of semiconductors, but can also have undesired effects on electronic and thermal transport, particularly in ultrascaled nanostructures, such as nanowires. Here we use all-atom molecular dynamics to study the effect that different concentrations and spatial distributions of vacancies have on the thermal conductivity of Si nanowires, overcoming the limitations of previous studies. Although vacancies are not as effective as the nanovoids found in e.g. porous Si, they can still reduce the thermal conductivity in ultrathin Si nanowires by more than a factor of two, when found in concentrations smaller than 1%. We also present arguments against the so-called self-purification mechanism, which is sometimes suggested to take place and proposes that vacancies have no influence on transport phenomena in nanowires., This work was financially supported by the European Commission through the Marie Skłodowska-Curie projects HORATES (GA-955837), by MCIN/AEI/10.13039/501100011033 under grant PID2020-119777GB-I00, and the Severo Ochoa Centres of Excellence Program under grant CEX2019-000917-S, and by the Generalitat de Catalunya under grant no. 2021 SGR 01519. Calculations were performed at the Centro de Supercomputación de Galicia (CESGA) within action FI-2022-1-0018 of the Red Española de Supercomputación (RES). We thank Antonio Cappai and Miguel Rubí for useful discussions., With funding from the Spanish government through the ‘Severo Ochoa Centre of Excellence’ accreditation (CEX2019-000917-S)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Electrically Programmed Doping Gradients Optimize the Thermoelectric Power Factor of a Conjugated Polymer

  • Liu, Jian
  • Craighero, Mariavittoria
  • Gupta, Vandna K.
  • Scheunemann, Dorothea
  • Paleti, Sri Harish Kumar
  • Järsvall, Emmy
  • Kim, Youngseok
  • Xu, Kai
  • Reparaz, J. Sebastian
  • Koster, L. Jan Anton
  • Campoy Quiles, Mariano
  • Kemerink, Martijn
  • Martinelli, Anna
  • Müller, Christian
Functionally graded materials (FGMs) are widely explored in the context of inorganic thermoelectrics, but not yet in organic thermoelectrics. Here, the impact of doping gradients on the thermoelectric properties of a chemically doped conjugated polymer is studied. The in-plane drift of counterions in moderate electric fields is used to create lateral doping gradients in films composed of a polythiophene with oligoether side chains, doped with 2,3,5,6-tetrafluoro-tetracyanoquinodimethane (F4TCNQ). Raman microscopy reveals that a bias voltage of as little as 5 V across a 50 µm wide channel is sufficient to trigger counterion drift, resulting in doping gradients. The effective electrical conductivity of the graded channel decreases with bias voltage, while an overall increase in Seebeck coefficient is observed, yielding an up to eight-fold enhancement in power factor. Kinetic Monte Carlo simulations of graded films explain the increase in power factor in terms of a roll-off of the Seebeck coefficient at high electrical conductivities in combination with a mobility decay due to increased Coulomb scattering at high dopant concentrations. Therefore, the FGM concept is found to be a way to improve the thermoelectric performance of not yet optimally doped organic semiconductors, which may ease the screening of new materials as well as the fabrication of devices., The authors gratefully acknowledge financial support from the Knut and Alice Wallenberg Foundation (grant agreement no. 2016.0220, 2020.0187, and 2022.0034), the Swedish Research Council (grant agreement no. 2018–03824), and the European Union's Horizon 2020 research and innovation programme through the Marie Skłodowska-Curie grant agreement no. 955837(HORATES). J.L. acknowledges financial support from the National Natural Science Foundation of China (Nos. 52273201). M.K. thanks the Carl Zeiss Foundation for financial support. Renee Kroon is acknowledged for synthesizing the conjugated polymer used in this study., With funding from the Spanish government through the ‘Severo Ochoa Centre of Excellence’ accreditation (CEX2019-000917-S)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

A surface passivated fluorinated polymer nanocomposite for carbon monoxide resistant plasmonic hydrogen sensing

  • Östergren, I.
  • Darmadi, Iwan
  • Lerch, Sarah
  • Silva, Robson Rosa da
  • Craighero, Mariavittoria
  • Paleti, Sri Harish Kumar.
  • Moth-Poulsen, Kasper
  • Langhammer, Christoph
  • Müller, Christian
Plasmonic hydrogen sensors are promising safety monitoring devices for the emerging hydrogen economy provided a fast response time and poisoning resistance can be achieved. Nanocomposites composed of palladium nanoparticles embedded in a polymer matrix facilitate rapid hydrogen diffusion if a fluorinated polymer is used, while a denser polymer such as atactic poly(methyl methacrylate) (PMMA) facilitates a high degree of gas selectivity. However, nanocomposites that combine a fast response with poisoning resistance have not yet been realized. Here, these two properties are achieved simultaneously by modifying the surface of a fluorinated polymer nanocomposite with a thin PMMA coating, which functions as a molecular sieve that effectively blocks carbon monoxide. The resulting surface passivated nanocomposite shows a high degree of poisoning resistance without compromising a fast sensing response of 2-3 seconds upon exposure to 100 mbar of hydrogen. The sensor signal and response are preserved over 55 cycles of synthetic air containing 5% hydrogen and 500 ppm of carbon monoxide, indicating that nanocomposites are a viable approach for the realization of robust hydrogen sensors., The authors acknowledge financial support from the Swedish Foundation for Strategic Research project RMA15-0052, the Knut and Alice Wallenberg Foundation for a Wallenberg Fellow Prolongation Grant and the European Union’s Horizon 2020 research and innovation programme through the Marie Skłodowska-Curie grant agreement no. 955837 (HORATES). Part of this work was carried out at the Chalmers Materials Analysis Laboratory (CMAL). The authors also acknowledge the Centre for Cellular Imaging at the University of Gothenburg and the National Microscopy Infrastructure, NMI (VR-RFI 2019-00022), for providing assistance with microtome sectioning. The authors thank Anders Mårtensson for his assistance with SEM-EDX measurements and Insplorion AB for providing the Ossila dip coater., With funding from the Spanish government through the ‘Severo Ochoa Centre of Excellence’ accreditation (CEX2019-000917-S)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

On The Thermal Conductivity of Conjugated Polymers for Thermoelectrics

  • Rodríguez Martínez, Xabier
  • Saiz, Fernan
  • Dörling, Bernhard
  • Marina, Sara
  • Guo, Jiali
  • Xu, Kai
  • Chen, Hu
  • Martin, Jaime
  • McCulloch, Iain
  • Rurali, Riccardo
  • Reparaz, J. Sebastian
  • Campoy Quiles, Mariano
The thermal conductivity (κ) governs how heat propagates in a material, and thus is a key parameter that constrains the lifetime of optoelectronic devices and the performance of thermoelectrics (TEs). In organic electronics, understanding what determines κ has been elusive and experimentally challenging. Here, by measuring κ in 17 π-conjugated materials over different spatial directions, it is statistically shown how microstructure unlocks two markedly different thermal transport regimes. κ in long-range ordered polymers follows standard thermal transport theories: improved ordering implies higher κ and increased anisotropy. κ increases with stiffer backbones, higher molecular weights and heavier repeat units. Therein, charge and thermal transport go hand-in-hand and can be decoupled solely via the film texture, as supported by molecular dynamics simulations. In largely amorphous polymers, however, κ correlates negatively with the persistence length and the mass of the repeat unit, and thus an anomalous, albeit useful, behavior is found. Importantly, it is shown that for quasi-amorphous co-polymers (e.g., IDT-BT) κ decreases with increasing charge mobility, yielding a 10-fold enhancement of the TE figure-of-merit ZT compared to semi-crystalline counterparts (under comparable electrical conductivities). Finally, specific material design rules for high and low κ in organic semiconductors are provided., The authors would like to acknowledge financial support from the Spanish Ministry of Science and Innovation through the “Severo Ochoa” Programme for Centers of Excellence in R&D and project reference PID2021-128924OB-I00 as well as the European Research Council (ERC) under grant agreement no. 648901. This work was financially supported by the European Commission through the Marie Skłodowska-Curie projects HORATES (GA-955837). J.M. is also grateful to the Spanish Ministry of Science and Innovation through project PGC2018-094620-A-I00. The authors also acknowledge the support from the Marie Skłodowska-Curie program (action no. 793726 – TELIOTES) and the Centro de Supercomputación de Galicia (CESGA) for the use of their computational resources. The authors acknowledge Prof. Alejandro R. Goñi (ICMAB-CSIC, ICREA) for his valuable help in setting up the Raman thermometry measurement platform. The authors are thankful to Dr. Aleksandr Perevedentsev (ICMAB-CSIC) for his know-how regarding the fabrication of free-standing films, as well as for the preparation of the drop cast DH6T films. The authors are very thankful to Prof. Paul Smith (ETH Zürich) for fruitful discussions about polymer processing and Prof. Christian Müller for his useful comments on this work, and the suggestions regarding thermal diffusivity. The authors also thank Andrés Gómez for performing the nanoindentation experiments. I.M. and H.C. acknowledge King Abdullah University of Science and Technology Office of Sponsored Research (OSR) under awards no. OSR-2018-CARF/CCF-3079, and OSR-4106 CPF2019 as well as EC FP7 Project SC2 (610115)., With funding from the Spanish government through the ‘Severo Ochoa Centre of Excellence’ accreditation (CEX2019-000917-S)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

A Universal, Highly Stable Dopant System for Organic Semiconductors Based on Lewis-Paired Dopant Complexes

  • Zapata Arteaga, Osnat
  • Perevedentsev, Aleksandr
  • Prete, Michela
  • Busato, Stephan
  • Floris, Paolo Sebastiano
  • Asatryan, Jesika
  • Rurali, Riccardo
  • Martín, Jaime
  • Campoy Quiles, Mariano
Chemical doping of organic semiconductors is an essential enabler for applications in electronic and energy-conversion devices such as thermoelectrics. Here, Lewis-paired complexes are advanced as high-performance dopants that address all the principal drawbacks of conventional dopants in terms of limited electrical conductivity, thermal stability, and generality. The study focuses on the Lewis acid B(C6F5)3 (BCF) and 2,3,5,6-tetrafluoro-7,7,8,8-tetracyanoquinodimethane (F4TCNQ) bearing Lewis-basic −CN groups. Due to its high electron affinity, BCF:F4TCNQ dopes an exceptionally wide range of organic semiconductors, over 20 of which are investigated. Complex activation and microstructure control lead to conductivities for poly(3-hexylthiophene) (P3HT) exceeding 300 and 900 S cm–1 for isotropic and chain-oriented films, respectively, resulting in a 10 to 50 times larger thermoelectric power factor compared to those obtained with neat dopants. Moreover, BCF:F4TCNQ-doped P3HT exhibits a 3-fold higher thermal dedoping activation energy compared to that obtained with neat dopants and at least a factor of 10 better operational stability., We thank Martin Kreuzer for extensive support and fruitful discussions at the Alba synchrotron BL01-MIRAS beamline. Jiali Guo and Dr. Edgar Gutierrez are also thanked for their support with the Alba experiments. We also thank Prof. Walter Caseri and Dr Marco D’Elia (Department of Materials, ETH Zürich) for generously contributing samples of poly(phenylene methylene)s as well as the many stimulating discussions. Dr Agustín Mihi (ICMAB-CSIC) is thanked for providing access to the Bruker IR spectrophotometry equipment. This work was financially supported by the European Commission through the Marie Skłodowska-Curie project HORATES (GA-955837), by the Spanish Ministry of Science and Innovation (MCIN/AEI/10.13039/501100011033) under grants PID2020-119777GB-I00, PID2021-128924OB-I00 and the Severo Ochoa Centres of Excellence Program under grant CEX2019-000917-S (particularly, PALOMA grant within ICMAB’s ‘Frontier Interdisciplinary Projects’ (FIP-2021) Program), and by the Generalitat de Catalunya under grant no. 2017 SGR 1506. The work of PSF has been carried out within the PhD program in Physics of the Universitat Autònoma de Barcelona (UAB). We thank the Centro de Supercomputación de Galicia (CESGA) for the use of their computational resources., With funding from the Spanish government through the ‘Severo Ochoa Centre of Excellence’ accreditation (CEX2019-000917-S)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Anisotropic Lattice Thermal Conductivity in Highly Ordered PEDOT Fibers

  • Floris, Paolo Sebastiano
  • Zahabi, Najmeh
  • Zozoulenko, Igor
  • Rurali, Riccardo
When it comes to sustainable and efficient energy solutions, organic semiconductors can play an important role in thermoelectric applications, since they are non-toxic, cheap, made of abundant chemical species, and show intrinsically low thermal conductivities. Their electrical conductivity can be optimized via doping. Yet, thermal conduction should be as low as possible and, to this end, the atomic scale mechanisms behind heat transport –e.g. the correlation between morphology and thermal conductivity or the role of doping– should be understood in detail. Fully atomistic molecular dynamics calculations of the lattice thermal conductivity of doped poly(3,4-ethylenedioxythiophene) (PEDOT) highly ordered, quasi-crystalline nanofibers are presented here. It is found that the conductivity along the backbone direction is not necessarily the highest, but it depends on the length of the PEDOT chains, thus the degree of anisotropy depends on the the aspect ratio of the nanofiber. Indeed, transport along the lamellar direction can be of the same order or higher than that of the backbone if their lengths are comparable. These results challenge the usual expectation that thermal conduction along the backbone largely exceeds those along the lamellar and π − π direction and have the important consequence that the anisotropy could be leveraged in thermal management applications., This work was financially supported by the European Commission through the Marie Skłodowska-Curie projects HORATES (GA-955837), by MCIN/AEI/10.13039/501100011033 under grant PID2020-119777GB-I00, and the Severo Ochoa Centres of Excellence Program under grant CEX2019-000917-S, and by the Generalitat de Catalunya under grant no. and 2017 SGR 1506. The work of PSF has been carried out within the PhD program in Physics of the Universitat Autònoma de Barcelona (UAB). We thank the Centro de Supercomputación de Galicia (CESGA) and National Academic Infrastructure for Supercomputing in Sweden (NAISS) for the use of their computational resources., With funding from the Spanish government through the ‘Severo Ochoa Centre of Excellence’ accreditation (CEX2019-000917-S)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Low-bandgap oligothiophene-naphthalimide oligomeric semiconductors for thermoelectric applications

  • Alonso Navarro, Matías J.
  • Zapata Arteaga, Osnat
  • Riera Galindo, Sergi
  • Guo, Jiali
  • Perevedentsev, Aleksandr
  • Gutiérrez Fernández, Edgar
  • Reparaz, J. Sebastian
  • Ramos, Mar
  • Müller, Christian
  • Martín, Jaime
  • Mas Torrent, Marta
  • Segura, José L.
  • Campoy Quiles, Mariano
State-of-the-art p-type organic conjugated polymers are mostly thiophene-based semiconductors. Still, novel chemical design and a fresh perspective on different polymer backbones could pave the way for new high-performing materials and a deep understanding of donor-acceptor conjugated assemblies. Herein we designed and synthesized two novel electroactive oligomeric materials based on a donor terthiophene unit endowed with a strong electron-withdrawing naphthalimide unit. This molecular assembly has been polymerized using a palladium cross-coupling reaction with two different linkers, 1,1,1,2,2,2-hexabutyldistannane and (4,8-bis((2-ethylhexyl)oxy)benzo[1,2-b:4,5-b’]dithiophene-2,6diyl)bis(trimethylstannane), to obtain the target polymers NIP3T-poly and NIP3T-BDT-poly, respectively. Both polymers exhibited an extended absorption up to 1000 nm and higher hole field-effect mobilities of up to 1.8 x 10-3 cm2V-1s-1, in comparison to the molecular assembly NIP3T, and precisely tuned energy levels that make them compatible with common p-type dopants like 2,3,5,6-tetrafluoro-7,7,8,8-tetracyanoquinodimethane (F4TCNQ). After optimizing the doping level, we obtained a thermoelectric figure of merit up to zT = 0.02 for NIP3T-BDT-poly, comparable with benchmark F4TCNQ-vapor doped polythiophenes., This work was financially supported by the European Commission through the Marie Skłodowska-Curie project HORATES (GA-955837), MICINN (PID2022-138908NB-C33, PID2022-141393OB-I00 and TED2021-129886BC43), through the “Severo Ochoa” Programme for Centers of Excellence in R&D (CEX2023-001263-S) and the UCM (INV.GR.00.1819.10759). MJAN gratefully acknowledges Universidad Rey Juan Carlos for his postdoctoral contract. S. RG. is thankful to Marie Skłodowska Curie Cofund, Beatriu de Pinós Fellowship (AGAUR-2019 BP 00200) and Marie Sklodowska-Curie Actions (H2020-MSCA-IF-2020) for Grant Agreement No. 101025608, IDEAL. We thank Anders Mårtensson for help with SEC measurements and Dr. Agustín Mihi (ICMAB-CSIC) for providing access to the Bruker IR spectrophotometry equipment, and Prof. Joaquim Puigdollers (UPC) for fruitful discussions, With funding from the Spanish government through the ‘Severo Ochoa Centre of Excellence’ accreditation (CEX2023-001263-S)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Doping Efficiency of Poly(benzodifurandione) from First Principles

  • Floris, Paolo Sebastiano
  • Zozoulenko, Igor
  • Rurali, Riccardo
Poly(benzodifurandione) (PBFDO) has emerged as a promising n-type conductive polymer (n-CP) for organic electronic applications, particularly in thermoelectrics (TE), due to its high doping efficiency and environmental stability. Unlike most high-performance p-type polymers, high-efficiency n-CPs are limited, posing a bottleneck in the TE module performance. In this study, we use first-principles electronic structure calculations to investigate the thermodynamic conditions that favor n-doping in PBFDO, focusing on the role of the temperature, chain length, and doping concentration. We compute the change in Gibbs free energy, ΔG, upon doping and explore how it varies with temperature and polymer chain length. Our results show that doping becomes more thermodynamically favorable at lower temperatures and in longer chains, with a strong dependence of ΔG on the doping level emerging as chain length increases. Notably, PBFDO can achieve favorable doping levels across various chain lengths and temperatures, with specific doping thresholds identified for different molecular weights. These findings suggest that lower synthesis temperatures could lead to more heavily doped, higher-conductivity PBFDO, and that chain length significantly influences achievable doping efficiency. This work provides insights for optimizing PBFDO doping strategies to enhance its performance in TE applications, bridging a key gap in organic semiconductor research., This work was financially supported by the European Commission through the Marie Skłodowska-Curie projects HORATES (GA-955837), by MCIN/AEI/10.13039/501100011033 under Grant PID2020-119777GB-I00, and the Severo Ochoa Centres of Excellence Program under Grant CEX2019-000917-S, and by the Generalitat de Catalunya under 2021 SGR 01519. The work of P.S.F. has been carried out within the Ph.D. program in Physics of the Universitat Autònoma de Barcelona (UAB). We thank the Centro de Supercomputación de Galicia (CESGA) for the use of their computational resources., With funding from the Spanish government through the ‘Severo Ochoa Centre of Excellence’ accreditation (CEX2023-001263-S)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Preventing Benzoquinone-Based Catalyst Aggregation Enables the One-Step Synthesis of Highly Conductive Poly(benzodifurandione) without Post-Reaction Purification

  • Huang, Jun-Da
  • Li, Qifan
  • Wang, Qingqing
  • Liu, Tiefeng
  • Jeong, Sang Young
  • Paleti, Sri Harish Kumar
  • Pol, Tom P. A . van der
  • Xu, Kai
  • Wu, Han-Yan
  • Pinchin, Natalie
  • Stoeckel, Marc-Antoine
  • Jin, Wenlong
  • Perevedentsev, Aleksandr
  • Liu, Xianjie
  • Reparaz, J. Sebastian
  • Campoy Quiles, Mariano
  • Woo, Han Young
  • Müller, Christian
  • Fahlman, Mats
  • Yang, Chi-Yuan
  • Fabiano, Simone
Conductive polymers have become crucial in advancing various electronic applications. While p-type materials like poly(3,4-ethylenedioxythiophene):polystyrene sulfonate (PEDOT:PSS) are widely used and produced at scale, the development of high-performance n-type polymers has lagged due to challenges in synthesis and scalability. In this work, a novel method is introduced to synthesize the highly conductive n-type polymer poly(benzodifurandione) (PBFDO) using α-tocopherylquinone (α-TQ) as a catalyst. This approach eliminates the need for post-reaction dialysis, a major obstacle to large-scale PBFDO production. By preventing catalyst aggregation, high electrical conductivity (>1320 S cm-1) is achieved, which remains stable in air for over 180 d, significantly simplifying the process. The α-TQ-synthesized PBFDO also exhibits excellent thermoelectric properties, with a power factor exceeding 100 µW m-1 K-2, placing it among the highest-performing n-type thermoelectric polymers. Additionally, residual α-TQ acts as a plasticizer, reducing the elastic modulus by over tenfold while maintaining high conductivity, making this material suitable for mechanically compliant electronics. Similarly, residual α-TQ lowers the thermal conductivity of PBFDO by more than an order of magnitude. The process is scalable, as demonstrated by producing high-conductivity ink in a 20 L reactor. This work presents an efficient and sustainable approach for large-scale n-type polymer production., J.-D.H. and Q.L. contributed equally to this work. This work was financially supported by the Knut and Alice Wallenberg Foundation (2021.0058, 2020.0187, 2021.0230, 2022.0034, 2023.0464, WWSC, and Wallenberg Initiative Materials Science for Sustainability WISE), the Swedish Research Council (2020-03243, 2020-04538, 2022-04053, and 2022-04553), the European Commission through the HORATES (GA-955837), IONIC (101148701), and SUNREY (GA-101084422) projects, and the Swedish Government Strategic Research Area in Materials Science on Functional Materials at Linköping University (Faculty Grant SFO-Mat-LiU 2009-00971). H. Y. Woo acknowledges financial support from the National Research Foundation (NRF) of Korea (2019R1A6A1A11044070)., With funding from the Spanish government through the ‘Severo Ochoa Centre of Excellence’ accreditation (CEX2023-001263-S)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Microstructural Evolution Dominates the Changes in theThermal Conductivity of Conjugated Polymers Upon Doping

  • Guo, Jiali
  • Xu, Kai
  • Asatryan, Jesika
  • Alonso Navarro, Matías Jesús
  • Zapata Arteaga, Osnat
  • Craighero, Mariavittoria
  • Perevedentsev, Aleksandr
  • Kroon, Renee
  • Ramos, María Mar
  • Segura, José L.
  • Martín, Jaime
  • Müller, Christian
  • Reparaz, J. Sebastian
  • Campoy Quiles, Mariano
In this study, the correlation between the changes in microstructure of conjugated polymers upon doping and their concomitant thermal transport properties is elucidated. Eight conjugated polymers across distinct doping systems are examined: molecular dopants, Lewis acid type dopants, and ion-exchange systems. These findings indicate that, upon doping, there is a decrease in out-of-plane thermal conductivity for five polymers characterized by high structural order, such as those based on thiophene, diketopyrrolopyrrole, and terthiophene-naphthalimide copolymers. Conversely, for polymers with less ordered structures, including regioregular poly(3-hexylthiophene) and thiophene-based polymers with oligoether side chains, an increase in out-of-plane thermal conductivity is observed. To elucidate these trends, several hypotheses are examined: i) enhanced intrinsic thermal anisotropy originating from backbone orientation, ii) variations in the crystalline to amorphous fraction, and (iii) alloying effects resulting from dopant incorporation. Grazing incidence wide-angle X-ray scattering reveals that in-plane alignment exerts a direct influence on both in-plane and out-of-plane thermal conductivities. Photooxidation experiments provide further insights into the role of alloy scattering. Ultimately, the in-plane thermoelectric figure of merit is ascertained for two diketopyrrolopyrrole-based polymers, underscoring the critical importance of measuring thermal and electrical properties in the same orientation to ensure precise thermoelectric evaluation., The authors acknowledge funding from the European Union's Horizon 2020 research and innovation programme through the Marie Skłodowska-Curie grant agreement no. 955837 (HORATES). The authors acknowledge financial support from the Spanish Ministerio de Ciencia, Innovación y Universidades and the for its support through Grant CEX2023- in the framework of the Spanish Severo Ochoa Centre of Excellence, and Grants PID2021-128924OB-I00, PID2020-119777GB-I00 (THERM2MAIN), PID2022-138908NB-C33, and PDC2021-121814-I00 (COVEQ). The authors also acknowledge Grant 2021-SGR-00444 (NANOPTO) from the Catalan agency AGAUR. The authors acknowledge Dr. Bernhard Dörling for support with thermoelectric measurements and Dr. Agustín Mihi as well as ICMAB-CSIC for access to and support with the FTIR equipment. This work has been carried out within the framework of the doctoral program in Material Science at the Universitat Autònoma de Barcelona in which J. G. was enrolled. The authors acknowledge support for the publication fee by the CSIC Open Access Publication Support Initiative through its Unit of Information Resources for Research (URICI)., With funding from the Spanish government through the ‘Severo Ochoa Centre of Excellence’ accreditation (CEX2023-001263-S)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Toward a Consensus Characterization Protocol for Organic Thermoelectrics

  • Dörling, Bernhard
  • Jacobs, Ian E.
  • Brunetti, Irene
  • Pataki, Nathan James
  • Yee, Shannon K.
  • Scheunemann, Dorothea
  • Kang, Keehoon
  • Zuo, Guangzheng
  • Reparaz, Juan Sebastián
  • Mori, Takao
  • Chabinyc, Michael L.
  • Müller, Christian
  • Caironi, Mario
  • Kemerink, Martijn
  • Campoy Quiles, Mariano
As the field of organic thermoelectrics advances toward maturity, an accurate and standardized reporting of performance metrics becomes essential to drive further progress and assess real-world viability. The common geometric form factors and material properties (conductivity, anisotropy, stability, etc.) differ from those of conventional bulk inorganic systems, and thus specific recommendations may apply. Herein, we compile prevalent points of concern in the reporting of thermoelectric performance for organic materials and devices. Moreover, we propose a list of critical factors and metrics that should be explicitly documented when reporting the performance of novel organic thermoelectric materials or devices., MCIN/AEI/10.13039/501-100011033/ through Severo Ochoa program CEX2023-001263-S, Marie Skłodowska-Curie grant agreement No 955837 – HORATES, Royal Society University Research Fellowship URF/R1/231287, Knut and Alice Wallenberg Foundation grant no. 2022.0034, National Science Foundation DMR 2310935, Marie Skłodowska-Curie grant agreement No 101226517–FADOS, National Research Foundation of Korea grant No. RS-2024-00436867., With funding from the Spanish government through the ‘Severo Ochoa Centre of Excellence’ accreditation (CEX2023-001263-S)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Counterion Dependent Side-Chain Relaxation Stiffens a Chemically Doped Thienothiophene Copolymer

  • Craighero, Mariavittoria
  • Jha, Meghna
  • Flores Vela, Elsa Veronica
  • Kimpel, Joost
  • Schaefer, Andreas
  • Guo, Jiali
  • Asatryan, Jesika
  • Peinador Veiga, Alberto
  • Haraguchi, Shuichi
  • Carlsson, Per Anders
  • Martín, Jaime
  • Campoy Quiles, Mariano
  • Müller, Christian
The electrical conductivity and elastic modulus of doped conjugated polymers tend to increase in tandem, which complicates the design of soft conductors. This work investigates how different dopant counterions influence the electrical and mechanical properties of a thienothiophene copolymer with triethylene glycol side chains. Sequential doping and proton-coupled electron-transfer were used to prepare samples with a comparable oxidation level neutralized with different counterions. Highly oxidized films featured a comparable electrical conductivity of about 100 S cm<sup>−1</sup> irrespective of the counterion size. Dynamic mechanical analysis revealed that the choice of counterion strongly impacts the sub-glass transition temperature, which varied from −44°C to −3°C. As a result, the elastic modulus at room temperature ranged from 0.05 GPa to 0.7 GPa for materials with a comparable oxidation level. Evidently, it is possible to decouple the electrical and mechanical properties of doped polymers, which are governed by charge transport along the backbone and side-chain relaxation, respectively. This insight opens up new opportunities for the design of soft conductors and more sustainable bioelectronic and wearable devices whose various soft and rigid components could be created with the same polymer., The authors gratefully acknowledge financial support from the European Union's Horizon 2020 research and innovation programme through the Marie Skłodowska-Curie grant agreement no. 955837 (HORATES), from the European Research Council (ERC) under grant agreement no. 101043417, from the Knut and Alice Wallenberg Foundation (2020.0187 and 2022.0034), and from the ICIU/AEI/10.13039/501100011033 for the “Severo Ochoa” program for Centres of Excellence CEX2023-001263-S. We thank Eric Tam from the Department of Industrial Materials Science at Chalmers for technical support of the XPS measurements. GIWAXS experiments were performed at the NCD-SWEET beamline of the ALBA Synchrotron with the collaboration of ALBA staff., With funding from the Spanish government through the ‘Severo Ochoa Centre of Excellence’ accreditation (CEX2023-001263-S)., Peer reviewed
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

In-plane thermal diffusivity determination using beam-offset frequency-domain thermoreflectance with a one-dimensional optical heat source

  • Xu, Kai|||0000-0001-6999-1904
  • Guo, Jiali
  • Raciti, Grazia
  • Goñi, Alejandro|||0000-0002-1193-3063
  • Alonso Carmona, Maria Isabel|||0000-0001-7669-5871
  • Borrisé, Xavier|||0000-0002-6491-4763
  • Zardo, Ilaria|||0000-0002-8685-2305
  • Campoy-Quiles, Mariano|||0000-0002-8911-640X
  • Reparaz, Juan Sebastian
We present an innovative contactless method suitable to study in-plane thermal transport based on beam-offset frequency-domain thermoreflectance using a one-dimensional heat source with uniform power distribution. Using a one-dimensional heat source provides a number of advantages as compared to point-like heat sources, as typically used in time- and frequency-domain thermoreflectance experiments, just to name a few: (i) it leads to a slower spatial decay of the temperature field in the direction perpendicular to the line-shaped heat source, allowing to probe the temperature field at larger distances from the heater, hence, enhancing the sensitivity to in-plane thermal transport; (ii) the frequency range of interest is typically <100 kHz. This rather low frequency range is convenient regarding the cost of the required excitation laser system but, most importantly, it allows the study of materials without the presence of a metallic transducer with almost no influence of the finite optical penetration depth of the pump and probe beams on the thermal phase lag, which arises from the large thermal penetration depth imposed by the used frequency range. We also show that for the case of a harmonic thermal excitation source, the phase lag between the thermal excitation and thermal response of the sample exhibits a linear dependence with their spatial offset, where the slope is proportional to the inverse of the thermal diffusivity of the material. We demonstrate the applicability of this method to the cases of: (i) suspended thin films of Si and PDPP4T, (ii) Bi bulk samples, and (iii) Si, glass, and highly-oriented pyrollitic graphite (HOPG) bulk samples with a thin metallic transducer. Finally, we also show that it is possible to study in-plane heat transport on substrates with rather low thermal diffusivity, e.g., glass, even using a metallic transducer. We achieve this by an original approach based on patterning the transducer using focused ion beam, with the key purpose of limiting in-plane heat transport through the thin metallic transducer.