Pasar al contenido principal

Desarrollo de materiales biodegradables y bio-basados a partir de la revalorización de residuos celu

JDC2024-053152-I

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal de Recursos Humanos
Subprograma Subprograma Estatal de Formación, Atracción y Retención del Talento Investigador e Innovador
Convocatoria Juan de la Cierva
Año convocatoria 2024
Plan Estatal 2024-2027 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario UNIVERSIDAD DE ALICANTE

Resultados relacionados

Resultados totales (Incluyendo duplicados): 6
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Environmentally Friendly Alternatives to Bis(2-ethylhexyl) Phthalate as Plasticizers for Poly(lactic acid)

  • Gómez-Caturla, Jaume|||0000-0001-8680-4509
  • Vicente-Vinas, Maria del Puig|||0009-0005-0024-1503
  • Garcia-Sanoguera, David|||0000-0002-1923-9519
  • Quiles-Carrillo, Luis|||0000-0001-8037-2215
  • Ivorra-Martinez, Juan|||0000-0001-8968-4899
  • Covas, José A.
[EN] This study evaluated a conventional petroleum derived diester plasticizer and three environmentally friendly diester plasticizers for polylactic acid (PLA), focusing on processing, mechanical, thermal, chemical, and surface properties. Bis(2-ethylhexyl) phthalate (DEHP), a widely used plasticizer for PLA, is derived from petrochemical sources and is classified as a pollutant, which motivated the search for biobased alternatives. PLA compounds containing biobased diester plasticizers were prepared by extrusion, and test specimens were obtained by injection molding. The results showed that the biobased plasticizers bis(2-ethylhexyl) maleate (DEHM) and bis(2-ethylhexyl) sebacate (DEHS) significantly improved ductility, which was confirmed by fracture surface analysis. Thermal and thermomechanical analyses indicated enhanced chain mobility, along with increased crystallization and a reduction in glass transition temperature. Chemical characterization confirmed that plasticization occurred through physical interactions, preserving the chemical integrity of the polymer matrix. In addition, diester plasticizer incorporation modified surface wettability, facilitating water diffusion and increasing affinity toward distilled water, which could be beneficial for applications such as biodegradable packaging or agricultural materials, where moisture interaction may influence end-of-life behavior and environmental degradation., This research is a part of the grant PID2023-152869OBC22, and the grant TED2021-131762 A-I00, funded by MCIN/AEI/ https://doi.org/10.13039/501100011033 and by the European Union NextGenerationEU /PRTR. The authors also thank Generalitat Valenciana - GVA, grant number CIGE/2023/46 and CIAICO/2023/253, for supporting this work. Funding for open access charge: CRUEUniversitat Politècnica de València. Microscopy services at UPV are also acknowledged for their help in collecting and analyzing FESEM images. J. Ivorra-Martinez wants to thank for the grant Grant JDC2024-053063-I funded by MICIU/AEI /https://doi.org/10.13039/5 01100011033 and by the FSE+. J. Gomez-Caturla wants to thank for the grant JDC2024-053152-I funded by MICIU/AEI /https://doi.org/10.13039/501100011033 and by the FSE+. Funding for open access charge: CRUE Universitat Politècnica de València.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Solvent-Free Synthesis of Poly(lactic acid) by Reactive Extrusion: Role of a-Tocopherol and Catalyst Loading

  • Mario Nicolás
  • Gómez-Caturla, Jaume|||0000-0001-8680-4509
  • Balart, Rafael|||0000-0001-5670-7126
  • Jiménez, Alfonso
  • Garrigós, María Carmen
  • Marset, Xavier
[EN] Poly(lactic acid) (PLA) was synthesized by ring-opening polymerization (ROP) of l-lactide through reactive extrusion using Sn(Oct)2 as the catalyst, 1-dodecanol as the initiator, and ¿-tocopherol as a natural antioxidant. This work combined reaction-time monitoring with structure¿property analysis to define the optimum processing window and formulation. In the first stage, samples collected during reactive extrusion were analyzed by differential scanning calorimetry (DSC) and Fourier-transform infrared (FTIR), showing the progressive consumption of l-lactide and the formation of PLA. The main monomer-related signals disappeared after approximately 12 min, while the most favorable thermal response was obtained after 18 min, indicating an optimum balance between conversion and thermal exposure. In the second stage, the effects of ¿-tocopherol and catalyst:monomer ratio were evaluated by mechanical, thermal, colorimetric, gel permeation chromatography (GPC), and FTIR analyses. For the 1:1000 formulation, ¿-tocopherol increased the molecular weight to 30,926 g mol¿1 and the tensile strength to 34.1 MPa while also enhancing crystallinity and preserving a lighter, less yellow appearance. Among the antioxidant-containing samples, the 1:1000 catalyst:monomer ratio provided the best overall balance between conversion, molecular weight, mechanical performance, and thermal behavior. FTIR confirmed successful PLA formation in the optimized formulations, whereas the 1:5000 sample retained lactide-related bands, consistent with incomplete conversion and inferior properties. These results demonstrate that reactive extrusion is a viable solvent-free route for PLA synthesis when residence time, natural antioxidant stabilization, and catalyst loading are jointly optimized., This research is a part of the grants PID2023-152869OB-C21, PID2023-152869OB-C22, and the grant TED2021-131762A-I00, funded by MCIN/AEI/10.13039/501100011033 and by the European Union "NextGenerationEU"/PRTR. The authors also thank Generalitat Valenciana - GVA, grant number CIGE/2023/46 and CIAICO/2023/253J. Gomez-Caturla wants to thank for the grant JDC2024-053152-I funded by MCIN/AEI/ 10.13039/501100011033 and, as appropriate, by "ESF Investing in your future" or by "European Union NextGenerationEU/PRTR".
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

High efficiency plasticizers for flexible thermoplastic zein processed by extrusion and injection molding

  • Benavides-Ramos, A.
  • Lázaro-Hernández, C.|||0009-0002-8250-9363
  • Gómez-Caturla, Jaume|||0000-0001-8680-4509
  • Lascano-Aimacaña, Diego Sebastián|||0000-0002-0996-1946
  • Balart, Rafael|||0000-0001-5670-7126
[EN] This study addresses the limited availability of injection-molded zein systems by evaluating three structurally contrasted plasticizers, diethylene glycol (DEG), dipropylene glycol (DPG), and diethanolamine (DEA), to produce thermoplastic zein by hot extrusion and injection molding. Beyond demonstrating melt processability, the work seeks to clarify how plasticizer chemistry governs the structure-property relationships of zein under scalable thermoplastic processing conditions. All formulations yielded homogeneous injection-molded specimens. FTIR and XRD revealed plasticizer-dependent perturbations in the protein matrix, while DSC and DMTA showed clear differences in thermomechanical softening. The linear and flexible structure of DEG promoted the strongest disruption/reorganization of zein packing, increasing molecular mobility and translating into the lowest glass transition temperature (Tg) (42.0 ºC for 25 DEG), highest ductility (elongations at break: 74.2%) and highest impact strength (~70¿kJ¿m¿2). In contrast, the branched structure of DPG and the amino-diol character of DEA produced more moderate plasticization, retaining higher stiffness and Tg values, while DEA strongly increased surface wettability (WCA< 10º). Bulk water uptake reached high maxima (~277¿310% at 7 days). Under controlled composting, near-complete disintegration occurred within 4¿6 weeks (20DPG slowest). Overall, plasticizer chemistry enables the injection molding of tunable zein parts with short composting disintegration times., This research was supported by grants PID2023 152869OB-C22 and TED2021 131762A-I00, funded by MCIN/AEI/10.13039/501100011033 and by the European Union NextGenerationEU /PRTR. D. Lascano acknowledges grant JDC2023 051885-I funded by MCIN/AEI/10.13039/501100011033 and by the ESF + . J. Gomez-Caturla wants to thank for the grant JDC2024 053152-I funded by MCIN/AEI/ 10.13039/501100011033 and, as appropriate, by ESF Investing in your future The authors also acknowledge the Generalitat Valenciana (GVA) for supporting this work through grants CIGE/2023/46 andCIAICO/2023/253. C. L¿ azaro-Hdez gratefully acknowledges the Generalitat Valenciana for funding a predoctoral position through the CIACIF program co-funded by the ESF Investing in your future (grantCIACIF/2023/244). Funding for open access charge: CRUE Universitat Politecnica de Valencia.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Incorporation of Apricot Shell Loads into Novel Highly Ductile Thermoplastic Zein Biopolymers Through Injection Molding for Food Packaging

  • Peñafiel-Alvarado, Jorge Israel
  • Novak, Jan
  • Brdlík, Pavel
  • Gómez-Caturla, Jaume|||0000-0001-8680-4509
  • Balart, Rafael|||0000-0001-5670-7126
  • Quiles-Carrillo, Luis|||0000-0001-8037-2215
[EN] The replacement of petroleum-based plastics with sustainable, biodegradable alternatives is a key challenge in the transition toward a circular economy. Zein, a maize-derived protein, is a promising candidate for biodegradable thermoplastics, but its limited ductility and processability have hindered wider adoption. This study addresses this gap by exploring the effect of apricot shell flour (ASF) on zein (ZEI) thermoplastic materials plasticized with 25 wt% diethylene glycol (DEG) and processed by extrusion and injection molding. To date, the use of DEG as a plasticizer for zein in thermoplastics and the incorporation of ASF as a synergistic filler¿plasticizer in such systems have not been reported, defining the novelty of this work. Mechanical analysis revealed an outstanding ductility. ZEI-DEG exhibited a strain at break of 57.2%, which was increased to 119.2% with 15% ASF, while impact strength rose from 6.4 to 15.9 kJ/m², confirming a synergistic plasticization effect between DEG and ASF. A decrease in glass transition was observed by dynamic mechanical thermal analysis with the incorporation of ASF, probably due to the interaction of uronic acids present in ASF with DEG and zein through hydrogen bonding. Morphology analysis showed good filler dispersion and good compatibility with the zein matrix. Thermogravimetric analysis (TGA) revealed a slight decrease in thermal stability with ASF, but materials remained stable up to 350 °C. Materials exhibited a progressive darkening with dark brown colors, providing a wood-like appearance that is potentially attractive for sustainable wood plastic composite applications such as packaging. The properties of these materials were far higher than the traditionally glycerol-plasticized zein materials. Overall, these findings highlight ASF as a promising bio-based filler that enhances flexibility and toughness of thermoplastic zein while maintaining good thermal behavior and creating aesthetically appealing natural composites. These green materials offer significant potential for biodegradable food packaging, furniture, and interior design products., This research is a part of the grant PID2023-152869OB-C22, and the grant TED2021-131762 A-I00, funded by MCIN/AEI/https://doi.org/10.13039/501100011033 and by the European Union NextGenerationEU /PRTR. The authors also thank Generalitat Valenciana - GVA, grant number CIGE/2023/46 and CIAICO/2023/253 and the Ministry of Education, Youth and Sports of the Czech Republic and the European Union European Structural and Investment Funds in the frames of Operational Programme Research, Development and Education project Hybrid Materials for Hierarchical Structures (HyHi, Reg. No. CZ.02.1.01/0.0/0.0/16_019/0000843), for supporting this work. J. Gomez-Caturla wants to thank for the grant JDC2024-053152-I funded by MCIN/AEI/https://doi.org/10.13039/5 01100011033 and, as appropriate, by ESF Investing in your future or by European Union NextGenerationEU/PRTR . Microscopy services at UPV are also acknowledged for their help in collecting and analyzing FESEM images. Funding for open access charge: CRUEUniversitat Politècnica de València.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Innovative Development and Characterization of Water Kefir Grains in thermoplastic composites prepared by injection molding

  • Peltzer, Mercedes Ana
  • Arrieta, Marina Patricia
  • Garcia-Garcia, Daniel|||0000-0002-2520-0186
  • Sanchez-Nacher, Lourdes|||0000-0002-8627-4576
  • Gómez-Caturla, Jaume|||0000-0001-8680-4509
  • Quiles-Carrillo, Luis|||0000-0001-8037-2215
[EN] This study focuses on developing highly efficient and biodegradable polymers using water kefir grains (WKG), glycerol and water to produce thermoplastic water kefir (TWK) and blending it with polylactic acid (PLA). This research demonstrates the feasibility of extrusion and injection molding processes to produce thermoplastic kefir as a sustainable alternative to petroleum-based plastics in the packaging industry. The mechanical properties of the developed materials reveal that TWK is highly ductile, with an elongation at break of 35%, and that this elongation decreases as the amount of PLA increases in the blends. On the other hand, elastic modulus and tensile strength increase with the PLA content. Thermal properties show that TWK is amorphous, but when PLA is added, crystallinity increases and all thermal transitions shift towards higher temperatures as the PLA content increases. Moreover, the glass transitions of TWK (¿55¿°C) and PLA (68¿°C) are also shifted due to the blending of both polymers. These results suggest the presence of limited interfacial interactions between both polymers rather than full thermodynamic miscibility. Despite that, miscibility is not complete, as it is demonstrated by the appearance of spherulites in FESEM images. As expected, all materials demonstrated to be completely biodegradable within 3 to 7 weeks under controlled compost soil conditions., This research is a part of the grants PID2023-152869OB-C22, TED2021-131762A-I00 and PID2024-157368NB-C32, funded by MCIN/AEI/10.13039/501100011033 and by the European Union NextGenerationEU /PRTRand by ERDF A way of making Europe. The authors also thank Generalitat Valenciana - GVA, grant number CIGE/ 2023/46 and CIAICO/2023/253, for supporting this work. Funded with Aid for First Research Projects (PAID-06-22), Vice-rectorate for Research of the Universitat Politecnica de Valencia (UPV). In addition, we thank Agencia Nacional de Promocion Científica y Tecnologica (Argentina) through PICT-2021-0092 and the National University of Quilmes (UNQ, Argentina) through the R&D program PUNQ R 990/19 Expte: 827- 1300/19. J. Gomez-Caturla wants to thank for the grant JDC2024- 053152-I funded by MCIN/AEI/10.13039/501100011033 and, as appropriate, by ESF Investing in your future or by European Union NextGenerationEU/PRTR . Funding for open access charge: CRUEUniversitat Politecnica de Valencia.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

High efficiency plasticizers for flexible thermoplastic zein processed by extrusion and injection molding

  • Benavides-Ramos, A.
  • Lazaro-Hdez, C.
  • Gomez-Caturla, J.
  • Lascano, Diego
  • Balart, R.
This study addresses the limited availability of injection-molded zein systems by evaluating three structurally contrasted plasticizers, diethylene glycol (DEG), dipropylene glycol (DPG), and diethanolamine (DEA), to produce thermoplastic zein by hot extrusion and injection molding. Beyond demonstrating melt processability, the work seeks to clarify how plasticizer chemistry governs the structure-property relationships of zein under scalable thermoplastic processing conditions. All formulations yielded homogeneous injection-molded specimens. FTIR and XRD revealed plasticizer-dependent perturbations in the protein matrix, while DSC and DMTA showed clear differences in thermomechanical softening. The linear and flexible structure of DEG promoted the strongest disruption/reorganization of zein packing, increasing molecular mobility and translating into the lowest glass transition temperature (T<inf>g</inf>) (42.0 ºC for 25 DEG), highest ductility (elongations at break: 74.2%) and highest impact strength (∼70 kJ m−2). In contrast, the branched structure of DPG and the amino-diol character of DEA produced more moderate plasticization, retaining higher stiffness and T<inf>g</inf> values, while DEA strongly increased surface wettability (WCA< 10º). Bulk water uptake reached high maxima (∼277–310% at 7 days). Under controlled composting, near-complete disintegration occurred within 4–6 weeks (20DPG slowest). Overall, plasticizer chemistry enables the injection molding of tunable zein parts with short composting disintegration times., This research was supported by grants PID2023–152869OB-C22 and TED2021–131762A-I00, funded by MCIN/AEI/10.13039/501100011033 and by the European Union “NextGenerationEU”/PRTR. D. Lascano acknowledges grant JDC2023–051885-I funded by MCIN/AEI/10.13039/501100011033 and by the ESF + . J. Gomez-Caturla wants to thank for the grant JDC2024–053152-I funded by MCIN/AEI/ 10.13039/501100011033 and, as appropriate, by “ESF Investing in your future” The authors also acknowledge the Generalitat Valenciana (GVA) for supporting this work through grants CIGE/2023/46 and CIAICO/2023/253. C. Lázaro-Hdez gratefully acknowledges the Generalitat Valenciana for funding a predoctoral position through the CIACIF program co-funded by the ESF Investing in your future (grant CIACIF/2023/244). Funding for open access charge: CRUE–Universitat Politècnica de València., Peer reviewed