Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 16
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Enhanced hydrothermal resistance of Y-TZP ceramics through colloidal processing

  • E. Rayón|||0000-0002-0653-2046
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
  • Manjón, Francisco-Javier|||0000-0002-3926-1705
  • Moreno, R.
  • Alcazar, C.
  • Jimenez-Pique, E.
  • Llanes, L.
Two commercial zirconia powders with 3mol% of yttria (TZ3YE and TZ3YS, labeled as ZE and ZS, respectively) supplied by Tosoh (Japan) were used for this study. Maximum colloidal stability for ZE was achieved by dispersing the powders in a mixture of water/ethanol of 90:10 (wt/wt) using a sonication probe. The rheological behavior of the suspensions was optimized in terms of solids content ranging from 20 to 33vol% and sonication time (06min), the best results being obtained after 2min. ZS samples were prepared to a solids loading of 30vol% in water dispersing with 2min-sonication. Samples obtained by slip casting in plaster molds were used for dynamic sintering studies, and fully dense and nanostructured specimens were obtained at temperatures of 1300 degrees C1350 degrees C (ZE samples) and 1400 degrees C per 2h (ZS samples). The Hardness (H) and Young's Modulus (E) properties of the specimens were studied by nanoindentation technique giving 17 and 250GPa mean values for H and E, respectively. The specimens were then forced to a low-temperature degradation (LTD) treatment at 130 degrees C for 240h in steps of 60h. Raman spectroscopy and nanoindentation results of hydrothermally treated samples showed the absence of transformation from tetragonal to monoclinic phase until 180h whereas the mechanical properties maintained constant even at the sample surface. After 240h of LTD, the monoclinic phase was detected on all specimens by Raman peaks centered at 180, 191, and 383cm1. The nanoindentation study revealed an important loss of mechanical features reaching 10 and 175GPa for H and E, respectively. In the case of the ZS specimens, no monoclinic phase is detected after 240h of LTD treatment and no decay of E or H is detected. The free defect microstructure reached for the ZS specimen revealed a higher hydrothermal resistance so that it is concluded that the excellent behavior against thermal degradation is possible due to the large uniformity obtained by colloidal processing rather than the particle size of the starting powders., This work has been supported by Spanish Ministry of Science and Innovation (Projects MAT2009-14144-C03-02, MAT2009-14369-C02-01, and MAT2008-03398). Authors thank Prof. M. Anglada for helpful comments and discussion. R Moreno thanks the Universidad Politecnica de Valencia for the concession of a grant in the frame of its Program of Support to R+D (PAID-02-11, R-1752). We also wish to acknowledge Rut Benavente for her excellent technical support.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Multiplexing of encrypted data using fractal masks

  • Barrera, J.F.
  • Tebaldi, M.
  • Amaya, D.
  • Furlan, W.D.
  • Bolognini, Nestor Alberto
  • Torroba, Roberto Daniel
  • Amaya, D
  • Monsoriu Serra, Juan Antonio|||0000-0003-3350-7951
In this Letter, we present to the best of our knowledge a new all-optical technique for multiple-image encryption and multiplexing, based on fractal encrypting masks. The optical architecture is a joint transform correlator. The multiplexed encrypted data are stored in a photorefractive crystal. The fractal parameters of the key can be easily tuned to lead to a multiplexing operation without cross talk effects. Experimental results that support the potential of the method are presented., This research was performed under grants TWAS-UNESCO Associateship Scheme at Centres of Excellence in the South, CONICET No. 0863 (Argentina), ANCYT PICT 1167 (Argentina), and Facultad de Ingenieria, Universidad Nacional de La Plata No. 11/I125 (Argentina), Sostenibilidad 2011-2012, and CODI (Universidad de Antioquia-Colombia). W. D. Furlan and J. A. Monsoriua acknowledge financial support from Ministerio de Economia y Competitividad (grant FIS2011-23175), Generalitat Valenciana (grant PROMETEO2009-077), and Universitat Politecnica de Valencia (grants PAID-05-11 and PAID-02-11), Spain.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Computation of eigenvalues in proportionally damped viscoelastic structures based on the fixed-point iteration

  • Lázaro, Mario|||0000-0003-4949-8295
  • Pérez Aparicio, José Luis
  • Epstein, M.
Linear viscoelastic structures are characterized by dissipative forces that depend on the history of the velocity response via hereditary damping functions. The free motion equation leads to a nonlinear eigenvalue problem characterized by a frequency-dependent damping matrix. In the present paper, a novel and efficient numerical method for the computation of the eigenvalues of linear and proportional or lightly non-proportional viscoelastic structures is developed. The central idea is the construction of two complex-valued functions of a complex variable, whose fixed points are precisely the eigenvalues. This important property allows the use of these functions in a fixed-point iterative scheme. With help of some results in fixed point theory, necessary conditions for global and local convergence are provided. It is demonstrated that the speed of convergence is linear and directly depends on the level of induced damping. In addition, under certain conditions the recursive method can also be used for the calculation of non-viscous real eigenvalues. In order to validate the mathematical results, two numerical examples are analyzed, one for single degree-of-freedom systems and another for multiple ones., The authors gratefully acknowledge the support of the Polytechnic University of Valencia under programs PAID 02-11-1828 and 05-10-2674 and of the National Science and Research Council of Canada.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Multiphysics and Thermodynamic Formulations for Equilibrium and Non-equilibrium Interactions: Non-linear Finite Elements Applied to Multi-coupled Active Materials

  • Pérez-Aparicio, José L.
  • Palma, Roberto
  • Taylor, R.L.
[EN] Combining several theories this paper presents a general multiphysics framework applied to the study of coupled and active materials, considering mechanical, electric, magnetic and thermal fields. The framework is based on thermodynamic equilibrium and non-equilibrium interactions, both linked by a two-temperature model. The multi-coupled governing equations are obtained from energy, momentum and entropy balances; the total energy is the sum of thermal, mechanical and electromagnetic parts. The momentum balance considers mechanical plus electromagnetic balances; for the latter the Abraham rep- resentation using the Maxwell stress tensor is formulated. This tensor is manipulated to automatically fulfill the angular momentum balance. The entropy balance is for- mulated using the classical Gibbs equation for equilibrium interactions and non-equilibrium thermodynamics. For the non-linear finite element formulations, this equation requires the transformation of thermoelectric coupling and conductivities into tensorial form. The two-way thermoe- lastic Biot term introduces damping: thermomechanical, pyromagnetic and pyroelectric converse electromagnetic dynamic interactions. Ponderomotrix and electromagnetic forces are also considered. The governing equations are converted into a variational formulation with the resulting four-field, multi-coupled formalism implemented and val- idated with two custom-made finite elements in the research code FEAP. Standard first-order isoparametric eight-node elements with seven degrees of freedom (dof) per node (three displacements, voltage and magnetic scalar potentials plus two temperatures) are used. Non-linearities and dynamics are solved with Newton-Raphson and New- mark-b algorithms, respectively. Results of thermoelectric, thermoelastic, thermomagnetic, piezoelectric, piezomag- netic, pyroelectric, pyromagnetic and galvanomagnetic interactions are presented, including non-linear depen- dency on temperature and some second-order interactions., This research was partially supported by grants CSD2008-00037 Canfranc Underground Physics, Polytechnic University of Valencia under programs PAID 02-11-1828 and 05-10-2674. The first author used the grant Generalitat Valenciana BEST/2014/232 for the completion of this work.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Encriptación óptica empleando llaves Weierstrass-Mandelbrot

  • Giménez, Fernando
  • Monsoriu, Juan A.
  • Barrera, John Fredy
  • Furlan, Walter D.
  • Tebaldi, Myrian
  • Bolognini, Néstor
  • Torroba, Roberto
[EN] This paper presents the generation of encryption keys using the local oscillating properties of the partial sums of Weierstrass-Mandelbrot fractal function. In this way, the security key can be replicated if the parameters used to obtain it are known. Therefore, these parameters can be sent instead of sending the key. This procedure reduces the amount of information to be sent and prevents possible interception of the key. Moreover, the key can not be affected by data loss or pollution. The effectiveness of the Weierstrass-Mandelbrot keys were demonstrated by computer simulation in a 4f optical encryption system and the double random phase encoding technique. These keys allow us to encrypt and to retrieve the information, which is the evidence of their effectiveness for data security. Furthermore, it is shown that if the encrypted data is obtained under an attack, it is not possible to access the information without the security key., [ES] En este trabajo se presenta la generación de llaves de encriptación aprovechando el carácter local oscilatorio y variable de las sumas parciales de la función fractal Weierstrass-Mandelbrot. Bajo este esquema, la llave de seguridad puede replicarse si se conocen los parámetros usados para su obtención. Por lo tanto, en lugar de enviar la llave de seguridad, se envían los parámetros que le permiten al usuario generarla en la estación desencriptadora. Este procedimiento permite reducir la cantidad de información a ser enviada y se evita la posible interceptación de la llave, además la llave no sufre pérdidas o contaminación. La efectividad de las llaves Weierstrass-Mandelbrot se demostró mediante simulaciones computacionales en un sistema óptico de encriptación 4f y la técnica de codificación de doble máscara de fase. Estas llaves permiten encriptar información y recuperarla, lo que representa la prueba de su efectividad para el manejo seguro de datos. Además, se demuestra que en la eventualidad de que un atacante pueda obtener el dato encriptado, éste no podrá acceder a la información si no posee la llave de seguridad., Este trabajo fue realizado con el apoyo de los siguientes subsidios: Sostenibilidad 2011-2012 y CODI (Universidad de Antioquia-Colombia), CONICET No. 0863/09 and No. 0549/12 (Argentina), and Facultad de Ingeniería, Universidad Nacional de La Plata No. 11/I168 (Argentina), Ministerio de Economía y Competitividad, España (programa FIS2011-23175) y Universitat Politécnica de Valencia, España (programas PAID-05-11 y PAID-02-11).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Elasto-thermoelectric non-linear, fully coupled, and dynamic finite element analysis of pulsed thermoelectrics

  • Pérez-Aparicio, José L.
  • Palma, Roberto
  • Moreno-Navarro, Pablo
This paper presents a numerical study on the influence of pulsed electric signals applied to the overcooling of thermoelectric devices. To this end, an experimental setup taken from the literature and a commercial cell are simulated using a complete, specially developed research finite element code. The electro-thermal coupling is extended to include the elastic field, demonstrating that the increment of cooling can produce mechanical failure. Numerical results are developed and the variation of overcooling versus pulse gain and versus duration is validated towards a new analytical expression and the experimental data. The issue of optimal intensity at steady-state is also newly developed. Thermal and mechanical trends are presented using constant and variable (with temperature) material properties for a single thermoelement. While some of the first trends are similar to those of published works, others are different or directly new, all closer to those of the experiments. The mechanical results have not been thoroughly studied until recently. The three-dimensional finite element mesh includes non-thermoelectric materials that are fundamental for the current study. Distribution of stresses during steady and transient states are shown inside the thermoelement, for five components and for the combined Tresca stress. Concentrations at corners of the lower side appear close to the cold face. Due to these concentrations, 27-node isoparametric, quadratic brick elements are used. It is shown that the mechanical field is an important factor in the design of pulsed thermoelectrics, since for practical applications the stress levels are close or slightly above the admissible limits., This research was partially supported by grants CSD2008-00037 Canfranc Underground Physics and Polytechnic University of Valencia under programs PAID 02-11-1828 and 05-10-2674.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Multiparametric computation of eigenvalues for linear viscoelastic structures

  • Lázaro, Mario|||0000-0003-4949-8295
  • Pérez-Aparicio, José L.
A new methodology for the computation of complex eigenvalues for multi-degree-of-freedom linear viscoelastic structures is presented. It is assumed that damping matrix does not only depends on the frequency but also on a set of parameters that control the dissipative mechanisms. Eigenvalues are then functions of a multi-variable array formed by damping parameters. The key idea is to approximate the eigenvalues as solutions of a specially developed differential equation. Proportional and non-proportional damping are studied separately. In addition, the error order and the computational complexity are rigorously analyzed. Numerical examples show very good agreement between proposed and exact solutions., This research was partially supported by the Grants CSD2008-00037 Canfranc Underground Physics and Polytechnic University of Valencia under programs PAID 02-11-1828 and 05-10-2674.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Dense nanostructured zirconia compacts obtained by colloidal filtration of binary mixtures

  • Benavente Martínez, Rut|||0000-0002-4566-9475
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
  • Alcázar, M.C.
  • Moreno, R.
As starting materials two commercial nanosized zirconias doped with 3 mol% of Y 2O 3 were used: a powder of about 100 nm (TZ3YE, Tosoh, Japan) and a colloidal suspension of about 15 nm (Mel Chemicals, UK). Colloidal stability in water was studied for both zirconias in terms of zeta potential as a function of deflocculant concentration and pH. Concentrated suspensions were prepared by dispersing the powder in the colloidal suspension to solids loadings ranging from 5 to 30 vol.% using a sonication probe to achieve dispersion. The rheological behavior was optimized in terms of solids content, deflocculant content and sonication time. Optimized suspensions with up to 25 vol.% solids showed a nearly Newtonian behavior and extremely low viscosities and maintain stable for long times (days) which is an important drawback of conventional nanoparticle suspensions. Samples obtained by slip casting in plaster moulds were used for dynamic sintering studies and dense, nanostructured specimens were obtained at temperatures of 1300-1400°C., This work has been supported by Spanish Ministry of Science and Innovation (Projects MAT2009-14144-C03-02 and MAT2009-14369-C02-01). R. Moreno thanks to Universidad Politecnica de Valencia for the concession of a grant in the frame of its Programme of Support to R + D (PAID-02-11, R-1752).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Handling uncertainty of resource division in multi agent system using game against nature

  • Skrzypczyk, Krzysztof
  • Mellado, Martin|||0000-0002-3429-5316
This paper addresses the problem of resource division for robotic agents in the framework of Multi Agent System. Knowledge of the environment represented in the system is uncertain, incomplete and distributed among the individual agents that have both limited sensing and communication abilities. The pick-up-and-collection problem is considered in order to illustrate the idea presented. In this paper a framework for cooperative task assignment to individual agents is discussed. The process of negotiating access to common resources by intercommunicating agents is modeled and solved as a game against Nature. The working of the proposed system was verified by multiple simulations. Selected, exemplary simulations are presented in the paper to illustrate the approach discussed., This study is partially supported by IMPA (Inspection & Manipulation of Food Products) project (ref. DPI2010-20286), funded by the Spanish Government MICINN and by Programa de Apoyo a la Investigacion y Desarrollo (PAID-02-11) of the Universitat Politecnica de Valencia.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Study of hysteretic thermoelectric behavior in photovoltaic materials using the finite element method, extended thermodynamics and inverse problems

  • Palma, Roberto
  • Pérez-Aparicio, José L.
  • Bravo, R.
The main objective of the present work is to develop and prove a theoretical explanation based on the Extended Non-Equilibrium Thermodynamics (ENETs) for the hysteretical thermoelectric behavior observed in certain thin-film photovoltaic materials. The ENET introduces dissipative fluxes in the entropy balance that could explain this behavior. To verify this explanation from a numerical point of view, results are generated using a Finite Element (FE) formulation based on the ENET and already developed in previous publications by the authors. In addition, an identification Inverse Problem (IP) is formulated; a cost function is defined as the quadratic difference between experimental and numerical results and the IP is solved minimizing the cost function using genetic algorithms. The conclusion is that the loop-like distributions are due to energy dissipation introduced by dissipative fluxes that are closely related with relaxation times. Also, the FE-IP combination permits to find an approximated characterization of properties for several materials from single experimental curves. Finally, several numerical simulations are proposed for laboratory experiments to further validate the theoretical interpretation and to confirm the relation between relaxation times and hysteresis., This research was partially supported by the Grants CSD2008-00037 Canfranc Underground Physics, Excelencia Junta Andalucia P08-TEP-03641 and Polytechnic University of Valencia under programs PAID 02-11-1828 and 05-10-2674.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

A viscous approach based on oscillatory eigensolutions for viscoelastically damped vibrating systems

  • Lázaro, Mario|||0000-0003-4949-8295
  • Pérez-Aparicio, José L.
  • Epstein, Marcelo
[EN] Dissipative mechanisms in linear multiple-degree-of-freedom viscoelastic systems are characterized by the dependence on the history of the velocity degrees-of-freedom via convolution integrals over kernel functions. As a result, damping matrices are frequency-dependent and, in general, state-space approach based methods are widely used for their resolution. This paper proposes a new approach suitable for modelling such systems via a viscous model with proportional damping, which approximates the response of the original viscoelastic system using the undamped eigenvectors together with the complex eigenvalues with oscillatory nature, neglecting those modes with non-viscous nature (negative real eigenvalues). It is rigorously demonstrated that the transfer function of any viscoelastic system can be expanded as the sum of the transfer function of certain viscous model and a residual term. The obtained viscous model, named Equivalent Viscous Model, is characteristic of each viscoelastic system. In order to study the bound of the residual term two indexes are introduced to describe, on one hand, the non-proportionality, or the modal decoupling capability of the damping matrix and, on the other hand, the damping level of the system. The proposed viscous model is validated through numerical examples simulating different conditions of proportionality and damping., The authors gratefully acknowledge the support of the Polytechnic University of Valencia under programs PAID 02-11-1828 and 05-10-2674 and of the National Science and Research Council of Canada.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Nondestructive monitoring of ageing of Alkali resistant Glass fiber reinforced cement (GRC)

  • Eiras Fernández, Jesús Nuño
  • Kundu, Tribikram
  • Bonilla Salvador, María Mercedes
  • Paya Bernabeu, Jorge Juan|||0000-0001-7425-5311
Glass fiber reinforced cement (GRC) is a composite material made of portland cement mortar and alkali resistant (AR) fibers. AR fibers are added to portland cement to give the material additional flexural strength and toughness. However, ageing deteriorates the fibers and as a result the improvement in the mechanical properties resulted from the fiber addition disappears as the structure becomes old. The aim of this paper is monitoring GRC ageing by nondestructive evaluation (NDE) techniques. Two different NDE techniques (1) nonlinear impact resonant acoustic spectroscopy analysis and (2) propagating ultrasonic guided waves are used for this purpose. Both techniques revealed a reduction of the nonlinear behavior in the GRC material with ageing. Specimens are then loaded to failure to obtain their strength and stiffness. Compared to the un-aged specimens, the aged specimens are found to exhibit more linear behavior, have more stiffness but less toughness. Finally, undisturbed fragments on the fracture surface from mechanical tests are inspected under the electron microscope, to understand the fundamental mechanisms that cause the change in the GRC behavior with ageing., The authors want to acknowledge the financial support of the Ministerio de Ciencia e Innovacion MICINN, Spain, and FEDER funding (Ondacem Project: BIA 2010-19933) and BES-2011-044624. Also thanks to PAID-02-11 Program from Universitat Politecnica de Valencia.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Exploring high-level features for detecting cyberpedophilia

  • Bogdanova, Dasha
  • Solorio, Thamar
  • Rosso, Paolo|||0000-0002-8922-1242
[EN] In this paper, we suggest a list of high-level features and study their applicability in detection of cyberpedophiles. We used a corpus of chats downloaded from http://www.perverted-justice.com and two negative datasets of different nature: cybersex logs available online, and the NPS chat corpus. The classification results show that the NPS data and the pedophiles’ conversations can be accurately discriminated from each other with character n-grams, while in the more complicated case of cybersex logs there is need for high-level features to reach good accuracy levels. In this latter setting our results show that features that model behaviour and emotion significantly outperform the low-level ones, and achieve a 97% accuracy., The work of Dasha Bogdanova was partially carried out during the internship at the Universitat Politecnica de Valencia (scholarship of the University of St. Petersburg). Her research was partially supported by Google Research Award. The collaboration with Thamar Solorio was possible thanks to her one-month research visit at the Universitat Politecnica de Valencia (program PAID-PAID-02-11 award n. 1932). The research work of Paolo Rosso was done in the framework of the European Commission WIQ-EI Web Information Quality Evaluation Initiative (IRSES Grant No. 269180) project within the FP 7 Marie Curie People, the DIANA-APPLICATIONS - Finding Hidden Knowledge in Texts: Applications (TIN2012-38603-0O2-01) project, and the VLC/CAMPUS Microcluster on Multimodal Interaction in Intelligent Systems.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Atomistic Simulation of Water Intrusion¿Extrusion in ITQ-4 (IFR) and ZSM-22 (TON). The role of Silanol Defects

  • Bushuev, Yuriy
  • Sastre Navarro, German Ignacio|||0000-0003-0496-6331
[EN] Water in pure silica zeolites (zeosils) may behave as a "bumper" by absorbing mechanical energy of the intruded water, as a "spring" by restoring after extrusion of the energy spent in intrusion, or as "shock absorber" by dissipating the energy. The understanding of how the structure and topology of the zeosils are responsible of such behavior has not yet been fully clarified. Molecular dynamics and molecular mechanics simulations of IFR- and TON-type zeosils have been performed in an attempt to elucidate the energetics of these materials after water intrusion-extrusion. We aim our simulations to capture the experimentally observed "bumper" and "spring" water-zeosil behavior of IFR and TON, respectively The excess energy with respect to dry zeosil was calculated, and this relates to the energetic response of the zeosil after water intrusion. We found that the excess energy of water-TON is larger than the energy of bulk water at any loading. The Small opening of the TON channel prevents the formation of energetically stable bulky water clusters. The Water content-was shown to be stabilized On a-certain loading range in Water-IFR was shown that any silanol defects' in IFR framework channels stabilize systems. Defect positions(silanol groups), which make the water-IFR system energetically stable, are found Silanol groups increase the hydrophilicity of IFR-type zeosil, initially hydrophobic. There are two factors explaining the bumper behavior (under high pressure, Water penetrates into the zeosil Channels and remains there even. after the pressure is released) of water-IFR systems: channel size and hydrolisis leading to framework breaking under large hydrostatic pressure. Silanol groups in channels are centers of water clusterization. The chemical stability of TON framework and its small channel size explain its spring behavior., We acknowledge Profs. J. Patarin and S. Rigolet for making available their experimental 29Si MAS NMR spectra. G.S. acknowledges Ministerio de Ciencia e Innovacion for funding through project MAT2007-64682. Y.G.B. acknowledges Universidad Politecnica de Valencia for a visiting professor fellowship through program PAID-02-11.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Study of the effects of thermal regime and alternative hormonal treatments on the reproductive performance of European eel males (Anguilla anguilla) during induced sexual maturation

  • Gallego Albiach, Victor
  • Mazzeo, Ilaria
  • Vilchez Olivencia, Maria Carmen
  • Peñaranda, D.S.
  • Carneiro, P. C. F.
  • Pérez Igualada, Luz María|||0000-0002-6678-7446
  • Asturiano, Juan F.|||0000-0002-6441-5294
[EN] Since 1960, the European eel (Anguilla anguilla) has suffered a dramatic reduction in natural stocks. Breeding in captivity is considered an alternative, but obtaining high quality sperm seems basic on this regard. The main objective of this study was to assess the effects of three thermal regimes (two of them variable: T10 and T15; and one of them constant: T20) and three hormonal treatments with different hormones (hCG, hCGrec and PSMG) on the induction of maturation in European eel males. In the case of the thermal regimes, our results demonstrated that the onset and progression of spermiation are strongly influenced, and perhaps closely regulated, by water temperature. T20 demonstrated the best results in all the sperm parameters (volume, density, motility, kinetic features, etc.) throughout most weeks of treatment, becoming a reliable and productive method for inducing spermiation in this species. In the case of hormonal treatments, the onset and progression of spermiation in European eel males were influenced by the hormone used. In this respect, hCGrec produced the best results in all the sperm parameters including volume, density, motility, kinetic features, etc., throughout most weeks of treatment, thus becoming an effective alternative treatment to the standard hCG treatment used to induce spermiation in eel species. Moreover, hCGrec gave rise to the best economical profitability, making it possible to obtain good quality sperm samples at a lower price than by using the other two hormonal treatments. © 2012 Elsevier B.V. All rights reserved Guardar / Salir Siguiente >, Funded by the European Community's 7th Framework Programme under the Theme 2 "Food, Agriculture and Fisheries, and Biotechnology", grant agreement no. 245257 (PRO-EEL) and Generalitat Valenciana (ACOMP/2012/086). Victor Gallego, Ilaria Mazzeo and M. Carmen Vilchez have predoctoral grants from the Spanish Ministry of Science and Innovation (MICINN), Generalitat Valenciana, and UPV PAID Programme (2011-S2-02-6521), respectively. Paulo C.F. Carneiro had post-doc grants from PAC-EMBRAPA and UPV PAID Programme (PAID-02-11). David S. Penaranda was supported by a contract co-financed by MICINN and UPV (PTA2011-4948-I).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Characterization of Real Eigenvalues in Linear Viscoelastic Oscillators and the Non-viscous Set

  • Lázaro, Mario|||0000-0003-4949-8295
  • Pérez-Aparicio, José L.
In structural dynamics, energy dissipative mechanisms with nonviscous damping are characterized by their dependence on the time-history of the response velocity, which is mathematically represented by convolution integrals involving hereditary functions. The widespread Biot damping model assumes that such functions are exponential kernels, which modify the eigenvalues set so that as many real eigenvalues (named nonviscous eigenvalues) as kernels are added to the system. This paper is focused on the study of a mathematical characterization of the nonviscous eigenvalues. The theoretical results allow the bounding of a set belonging to the real negative numbers, called the nonviscous set, constructed as the union of closed intervals. Exact analytical solutions of the nonviscous set for one and two exponential kernels and approximated solutions for the general case of N kernels are developed. In addition, the nonviscous set is used to build closedform expressions to compute the nonviscous eigenvalues. The results are validated with numerical examples covering single and multiple degree-of-freedom systems where the proposed method is compared with other existing one-step approaches available in the literature., The authors gratefully acknowledge the support of the Polytechnic University of Valencia under Program Nos. PAID 02-11-1828 and 05-10-2674.