Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 26
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Experimental study of the impact of water properties on radon measurement by liquid scintillation counting using a factorial design

  • Trull-Hernandis, Cristina|||0000-0002-4182-6808
  • Martínez-Gómez, Mónica|||0000-0003-2401-9403
  • Sancho, M.|||0000-0002-9566-1949
  • Juste-Vidal, Belen-Jeanne|||0000-0003-1978-3765
  • Verdú Martín, Gumersindo Jesús|||0000-0001-5098-080X
[EN] This study employs a factorial experimental design to assess the influence of water physicochemical parameters on radon concentration measurements by liquid scintillation counting (LSC). Four water quality parameters are selected for this purpose to evaluate their potential effects ¿ and their potential interactions ¿ on the two-phase direct LSC method of radon in water measurement. The factors considered are pH, electrical conductivity (EC), turbidity and total organic carbon (TOC). The results assess how variations in these parameters significantly affect radon measurements. Since the performed variations do not have a significant effect, measurements under the conditions of real aqueous scenarios directly represent actual radon concentrations in water; and no correction factor is required., This work has been funded by the following Universitat Politècnica de Valencia projects: two entitled Estudio de la Transferencia de Radón a Traves de Distintos Medios (Suelo, Agua y Aire). Aplicacion para la Protección de la Población y de Profesionales Expuestos , with references (PAID-11-23)-UPV and (PAID-11-24)-UPV, and a third project entitled Estudio de la transferencia de radon del agua al aire en diferentes condiciones fisicoquímicas para la prediccióde la concentración en aire en espacios cerrados , referenced as (PAID-01-21)-UPV.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Experimental Analysis of the Temporal Variability of the V2V Channel at 5.9 GHz

  • Chakkour, Yousra
  • Fernández, Herman
  • Rodrigo Peñarrocha, Vicent Miquel|||0000-0002-8075-4851
  • Rubio Arjona, Lorenzo|||0000-0003-3882-4673
  • Reig, Juan|||0000-0003-4541-9326
[EN] Vehicle-to-vehicle (V2V) wireless communication systems are crucial for intelligent transportation applications such as traffic load control, autonomous vehicles, and collision avoidance. Therefore, it is essential to thoroughly understand the realistic V2V channel propagation conditions to develop suitable V2V communication systems and standards. However, due to high costs, most existing V2V studies focus on characterizing the vehicular channel theoretically and comparing it with simulation data or studying the empirical V2V channel in a specific scenario. In this work, we investigate the time variability of the received signal based on experimental data collected in an extensive measurement campaign at 5.9 GHz in a large set of propagation environments: urban-high traffic density, urban-low traffic density, suburban, highway, and rural environments. The time-variability of the received signal is characterized by time and frequency. The relationship between coherence time and the terminal velocity, coherence time and transmitter-receiver separation distance, and the relationship between Doppler spread and both effective velocity and separation distance, have been investigated. Furthermore, the correlation between coherence time and separation distance and effective velocity was investigated, as well as the correlation between Doppler spread and separation distance and effective velocity. The results provide a deeper understanding of the temporal variability of the channel and how it is influenced by factors such as traffic density, unique/multiple driving directions, terminal speed, separation distance, characteristics of the propagation environment, and visibility conditions. This knowledge is crucial for developing vehicular communication systems and can be applied to design strategies that reduce temporal variability in received signals., This work was supported in part by MCIN/AEI/10.13039/501100011033 through the I+D+i Project under Grant PID2020-119173RB-C21, in part by the Vicerrectorado de Investigacion de la Universitat Politecnica de Valencia under Grant PAID-11-24, and in part by CRUE-Universitat Politècnica de València.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Conceptual Framework for Hospital Bed Management in Industry 4.0 Context

  • Moya-Ruiz, Laura
  • Cuenca, L.|||0000-0003-3589-4182
  • Alemany Díaz, María Del Mar|||0000-0002-0992-8441
  • Ortiz-Barrios, Miguel
[EN] Optimizing hospital bed management (HBM) is essential to balance capacity, reduce waiting times and ensure efficient patient flow. However, persis-tent challenges in real-time data integration, interdepartmental coordination, and adoption of Industry 4.0 (I4.0) technologies stand in the way of progress in this field. This study proposes a conceptual framework for HBM, developed through a systematic revision of literature reviews. The framework categorizes key dimen-sions, integrating hospital-related factors, patient characteristics, objectives and performance metrics, decisions, modelling techniques and solution methods, with strategies and the role of I4.0 technologies. Unlike previous studies, it provides a structured and holistic perspective, emphasizing the role of digital health in opti-mizing decision making and resource allocation. The findings highlight research gaps in interoperability, solution methods, real-time optimization, and emphasize the need for scalable and resilient hospital management models. This framework serves as a foundation for future research and practical improvements in HBM., This research has been funding by the Vicerrectorado de Investigación de la Universitat Politècnica de Valencia (PAID-11-24).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Exploring the Impact of 3D Printing Variables on Gear Surface Finish and Wear Behavior

  • Montava-Jorda, Sergi|||0000-0002-5378-0333
  • García-Carrasco, Sergio|||0009-0001-9854-0309
  • Sanchez-Caballero, Samuel|||0000-0001-5322-8082
  • Alejandro de la
  • Eixerés Tomás, Beatriz|||0000-0001-8841-2429
[EN] As 3D printing technology continues to advance, it offers unprecedented opportunities to manufacture complex components such as gears. This study investigates the influence of various variables associated with 3D printing, particularly using the fused deposition modeling (FDM) method, on the surface finish of gears. Additionally, it outlines future research directions aimed at understanding how surface finish behavior correlates with wear resistance. The research begins with an in-depth analysis of the key variables involved in 3D printing gears using the FDM technique. These variables include extrusion temperature, printing speed and layer height. By systematically varying these parameters, the study aims to find their individual and collective effects on the surface finish of 3D printed gears. Experimental tests are carried out to evaluate the impact of each variable on the quality of the surface finish. Parameters such as surface roughness, uniformity of material deposition and layer adhesion are meticulously evaluated. The results demonstrate that variables such as extrusion temperature and layer height exert a significant influence on gear surface finish, while printing speed may have less pronounced effects. In summary, this study highlights the importance of understanding how various 3D printing variables affect gear surface finish and wear behavior. It identifies future areas of research that could provide a better understanding of these phenomena and lead to significant advances in the manufacturing of 3D printed gears.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Comparison of sol-gel derived carbon xerogels synthesized from different phenolic precursors and solvents: electrical conductivity and dielectric relaxation

  • Belguesmi, Aymen
  • Souilah, Amal
  • Ghrasallah, Aya
  • Fattoum, Arbi
  • Arous, Mourad
  • Elaloui, Elimame
  • Garcia-Bernabe, Abel|||0000-0002-9740-0830
[EN] Carbon xerogels based on resorcinol/formaldehyde (R/F) and pyrogallol/formaldehyde (P/F) were synthesized via a sol-gel route using hydrochloric acid as catalyst, with distilled water or acetone as solvent, in order to perform a comparative study of precursor and solvent effects on their structural and electrical properties. Scanning electron microscopy reveals that all samples exhibit a nanospheres-based morphology, while FTIR spectroscopy confirms the presence of characteristic functional groups associated with the phenolic precursors. Nitrogen adsorption-desorption measurements at 77 K indicate a predominantly mesoporous texture with relatively low specific surface areas. The AC electrical conductivity follows Jonscher's universal power law, characteristic of charge transport in disordered materials. A decrease in conductivity is observed at low temperatures, followed by a thermally activated increase above a transition temperature that depends on the precursor-solvent combination. The dielectric permittivity decreases with increasing temperature at low temperatures and tends to stabilize below the transition temperature. Analysis using the electric modulus formalism reveals two distinct relaxation processes. The high-frequency relaxation mode exhibits a temperature dependence similar to that of the electrical conductivity, with comparable activation energies, suggesting a common charge transport mechanism. The low-frequency relaxation is attributed to electrode-sample interfacial polarization effects. These results highlight the significant role of sol-gel synthesis parameters, particularly precursor nature and solvent choice, in tailoring the dielectric relaxation and electrical conductivity of xerogels., Abel Garcia Bernabe thanks the Vicerrectorado de Investigacion de la Universitat Politecnica de Valencia, Spain, for the financial support of the project (PAID-11-24).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Q-Learning for Online PID Controller Tuning in Continuous Dynamic Systems: An Interpretable Framework for Exploring Multi-Agent Systems

  • Ibarra-Pérez, Davor Matías Samuel
  • Garcia-Nieto, Sergio|||0000-0002-2722-742X
  • Sanchís Saez, Javier|||0000-0001-9697-2696
[EN] This study proposes a discrete multi-agent Q-learning framework for online tuning of PID controllers in continuous dynamic systems with limited observability. Each PID gain (Kp, Ki, Kd) is adjusted by an independent learning agent operating in a discrete state space defined by its own gain value. At each decision step, agents choose among three actions: decrease, keep, or increase the gain, and they act simultaneously at fixed decision intervals. This design helps preserve quasi-stationary conditions from the agents’ perspective and supports convergence. Coordination is achieved through a shared cumulative global reward that combines system-performance terms with time and control-effort penalties, as well as stability incentives, guiding exploration toward control objectives. Implemented in Python, the framework is validated on two nonlinear control problems: a water-tank system and an inverted pendulum (cart-pole). The agents reach initial convergence after approximately 300 and 500 episodes, respectively, and obtain overall success rates of 49.6% and 46.2% over 5,000 training episodes. Results show sustained learning toward effective PID parameter settings capable of stabilizing both systems without requiring explicit dynamic models. These findings support the feasibility of a low-complexity, discrete reinforcement-learning approach for online adaptive PID tuning, producing interpretable and reproducible control policies and providing a foundation for future hybrid schemes combining classical control theory with reinforcement-learning agents., This research was funded by Vicerrectorado de Investigación de la Universitat Politècnica de València (PAID-11-24) and supported by Agencia Nacional de Investigación de Chile ANID BECAS/DOCTORADO EN EL EXTRANJERO 72230436-2023.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Digital Resilience and Communication Strategies in Underfunded Museums in Argentina and Spain (2020-2024)

  • Martí Testón, Ana|||0000-0002-5058-2868
  • Climent-Ferrer, Juan José|||0000-0003-4130-6439
  • Muñoz García, Adolfo|||0000-0003-2435-3348
  • Solanes, J. Ernesto|||0000-0001-5011-4872
  • Gracia Calandin, Luis Ignacio|||0000-0001-9258-9286
  • Lanusse, Lucía
[EN] Between 2020 and 2024, museums underwent accelerated digital transformation driven by the global health crisis and technological advances, exposing deep inequalities in access to technology and communication capabilities. Museums with limited resources had to rethink their digital strategies to sustain audience engagement and cultural relevance. This article presents a comparative study of museums in Argentina and Spain with restricted budgets, analyzing how they responded to challenges of uncertainty and scarcity. Using a mixed methodology¿surveys of 22 professionals, interviews with directors of four representative museums, and qualitative case studies¿this study examines the implemented solutions and their impacts. The findings highlight innovative practices grounded in creativity, strategic alliances, and intensive use of social media. Argentine museums excelled in tactical adaptation amid economic instability, while Spanish institutions showed stronger strategic planning. Private museums proved more flexible than their public counterparts, which faced greater bureaucratic constraints. This work contributes to debates on institutional resilience and offers a framework for sustainable digital communication in resource-limited contexts., This work received funding from the European Union's DIGITAL Europe Programme under Grant Agreement No. 101226207 (project AI-SECRETT), from the Spanish Government under Grant PID2024-156583OB-I00 (funded by MCIN/AEI/10.13039/501100011033), and from the Generalitat Valenciana under Grant CIGE/2024/195.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Laboratory-scale setup for radon transport monitoring in radionuclide-rich soils: Key points identification and protocols development

  • Trull-Hernandis, Cristina|||0000-0002-4182-6808
  • Moreno-Ramón, Héctor|||0000-0002-4080-0876
  • Sancho, M.|||0000-0002-9566-1949
  • Lidón, Antonio|||0000-0002-0455-4348
  • Juste-Vidal, Belen-Jeanne|||0000-0003-1978-3765
[EN] A laboratory-scale experimental setup has been developed to simulate radon transport from radionuclide-rich soils under dynamic conditions. The setup allows simultaneous monitoring of the mobility of radon gas by leaching and by exhaling into the air phase under varying soil moisture conditions. Given that radon is a radioactive gas classified as Group 1 human carcinogen and stands as the 2nd reason for lung cancer worldwide, understanding its release and transport mechanisms in any environment is essential for effective radiological risk assessment. This work highlights the key aspects that must be considered and controlled to ensure a reproducible and stable experimental design that emulates the configuration of scenarios such as phosphate waste ponds and zones where radioactive content is distributed throughout the terrain. The identification of critical operational parameters provides a robust framework on what to consider when addressing the radon transport characterization and, later, be able to investigate the influence that environmental and the soil conditions have over radon release mechanisms., This work has been funded by two Universitat Politècnica de València projects, both entitled Estudio de la Transferencia de Radón a Través de Distintos Medios (Suelo, Agua y Aire). Aplicación para la Protección de la Población y de Profesionales Expuestos , with references (PAID-11-23)-UPV and (PAID-11-24)-UPV, and a third project entitled Estudio de la transferencia de radón del agua al aire en diferentes condiciones fisicoquímicas para la predicción de la concentración en aire en espacios cerrados , referenced as (PAID-01-21)-UPV.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Crisis Disinformation and Verification Dynamics in the València 2024 DANA

  • Climent-Ferrer, Juan José|||0000-0003-4130-6439
  • Solanes, J. Ernesto|||0000-0001-5011-4872
  • Martí Testón, Ana|||0000-0002-5058-2868
  • Moriniello, Flavio|||0009-0006-0360-8822
  • Muñoz García, Adolfo|||0000-0003-2435-3348
  • Gracia Calandin, Luis Ignacio|||0000-0001-9258-9286
[EN] This study examines the circulation of disinformation during the 2024 València DANA (high-altitude isolated depression), which produced torrential rainfall across eastern and southern Spain between 29 and 31 October 2024. Using a quantitative content analysis, it analyzes the 100 most viral false or misleading claims, classifying them by typology, format, dissemination channel, and narrative strategy. Findings show an ecosystem dominated by conspiracy narratives about the causes of the disaster and by audiovisual content¿particularly short videos and images¿which achieved substantially greater reach than textual posts. Narrative mechanisms such as decontextualization, emotional appeal, and political polarization were recurrent and often combined. Verification efforts that matched the original format were associated with higher relative correction reach, although their observable diffusion remained lower than that of the false claims in the analyzed sample. Overall, the study highlights the cross-platform and multimodal dynamics of crisis disinformation and underscores the need for proactive, technologically supported communication strategies. These include automated monitoring, multimodal verification, and interoperable digital infrastructures for crisis communication., This work has received funding from the European Union s DIGITAL Europe Programme under Grant Agreement No. 101226207 (project AI-SECRETT), from the Spanish Government under Grant PID2024-156583OB-I00 (funded by MICIU/AEI/10.13039/501100011033), and from the Generalitat Valenciana under Grant CIGE/2024/195.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Energy Optimisation and Performance Enhancement in Nutrient Concentration from AnMBR Effluent via Electrodialysis for Resource Recovery

  • Hernández Cuenca, Silvia
  • Serralta Sevilla, Joaquín|||0000-0001-5015-0689
  • Barat, Ramón|||0000-0003-0484-3614
  • Carrillo-Abad, J.
  • Bouzas, A.
[EN] Optimising energy consumption in electrodialysis systems treating real wastewater effluents remains a challenge, which is essential to be feasible and applicable. In this sense, long-term experiments were conducted under varying currents and applied voltages (0.1A, 7.5V and 10V), aiming to determine the best operating conditions. Subsequently, long-term experiments were performed regarding operational mode in one-stage and two-stage, number of cell pairs, relaxation stages and different influent nutrient concentration to determine the most suitable configuration of an electrodialysis stack treating free-sulphide Anaerobic Membrane Bioreactor effluent. All experiments performed successfully in terms of efficiencies, achieving 88.8±3.1% and 79.6±5.1% nitrogen and phosphorus removal, with 80.2±7.7% and 73.6±11.3% recovery, respectively. Approximately 100% of total current efficiency resulted in experiments, confirming good performance, although only a tiny fraction of current is used by the ions of interest. The best one-stage performance occurred at 7.5V, improved when operating in two stages and when increasing number of cell pairs. Indeed, two-stages operation with 20 cell pairs represented the most favourable condition, enabling compliance with DIRECTIVE (EU) 2024/3019 while maintaining low energy demand (0.17 kWh/m3, 29.92 kWh/kg P recovered, and 4.05 kWh/kg N recovered). Relaxation stages provided no further improvements, whereas higher influent nutrient concentration enhance nutrient recovery., This research work has been supported by the Spanish Ministry of Science and Innovation by "RECREATE" (PID2020-114315RB-C21/22) and "MEM4REC" (CTM2017-86751-C2-1/2-R) projects, jointly with the European Regional Development Fund (ERDF) , which are gratefully acknowledged. Authors would also like to thank the Vice-Rectorate for Research at the Universitat Politecnica de Valencia (PAID-11-24 and PAID-01-23) and the Vice-Rectorate for Research at the Universitat de Valencia (UV-INV-AE-3673218) for their support.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Decyl-riboflavin: membrane-targeted lipophilic photosensitizer for lipid peroxidation and phototoxicity in HeLa cells under blue light irradiation

  • Ardila Padilla, Carlos A.
  • Uribe Mayor, M. Sol
  • Urrutia, Maria Noel
  • Thomas, Andres H.
  • Dantola, M. Laura
  • Layana, Carla
  • Vignoni, Mariana
  • Dillon, Macarena-Noeli
  • Rodríguez Muñiz, Gemma María|||0000-0001-8989-2401
  • Andreu, Inmaculada|||0000-0003-3409-9443
  • Lhiaubet, Virginie Lyria|||0000-0002-8205-8892
[EN] Photodynamic therapy (PDT) exploits the controlled generation of reactive species to selectively destroy target cells, offering a minimally invasive alternative to conventional cancer and antimicrobial treatments. A key determinant of PDT efficacy is the ability of the photosensitizer (PS) to localize within lipid membranes, where proximity to polyunsaturated lipids maximizes oxidative damage. Riboflavin (Rf, Vitamin B2) is a biocompatible, naturally occurring PS with absorption in the blue light range; however, its inherent hydrophilicity limits membrane interaction. Here, we report the photochemical and biological characterization of 3-decyl-riboflavin (decyl-Rf), a lipophilic Rf derivative designed to direct oxidative damage specifically to the lipid bilayer under blue LED irradiation. Decyl-Rf generates singlet oxygen (Type II) while simultaneously operating through a Type I mechanism. This dual capacity translates into extensive lipid peroxidation and membrane disruption in biomimetic systems, effects essentially absent for hydrophilic Rf. Interaction studies with serum albumin reveal strong ground-state complex formation, which markedly reduces cellular uptake under serum-containing conditions. In HeLa cells, decyl-Rf is efficiently internalized and localizes preferentially in lipid-rich compartments, inducing significant phototoxicity upon blue light irradiation. These results position decyl-Rf as a potent membrane-targeted PS, with its lipid peroxidation capacity suggesting a possible contribution to regulated cell death pathways and provide a mechanistic foundation for lipophilic flavin derivatives as next-generation agents for blue light PDT in oncological and antimicrobial applications., This work was partially supported by Consejo Nacional de Investigaciones Cientificas y Tecnicas (CONICET, PIP 2023-0187), Agencia Nacional de Promocion Cientifica y Tecnologica (ANPCyT-Grants PICT 2019-3416 and 2020-3103) and Universidad Nacional de La Plata (UNLP-Grant 11/X975 and 11/X1021). Financial support from Vicerrectorado de Investigacion de la Universitat Politecnica de Valencia (PAID-11-24), the Spanish (projects PID2021-128348NB-I00, PID2024-162272NB-I00, Severo Ochoa Center of Excellence Program CEX2021-001230-S, funded by MCIN/AEI/https://doi.org/10.13039/5011 00011033/and "FEDER a way of making Europe") and regional (regional (grant CIGRIS/2022/091 to MD) governments is acknowledged. The authors thank CONICET and CSIC for supporting their collaboration through a Project of International Cooperation (DD216/25). CAAP thanks CONICET for doctoral fellowship. MSUM thanks Comision de Investigaciones Cientificas for graduate training fellowship.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Electrodialysis Parameter Optimisation following Aeration Strategy of Anaerobic Membrane Bioreactor effluent to Enhance Water Quality and Nutrient Recovery

  • Hernández Cuenca, Silvia
  • Serralta Sevilla, Joaquín|||0000-0001-5015-0689
  • Barat, Ramón|||0000-0003-0484-3614
  • Carrillo-Abad, J.
  • Bouzas, A.
[EN] Considering scaling and membrane adsorption limiting phosphorus recovery in previous studies, this work proposes integrating Anaerobic Membrane Bioreactor effluent aeration with Electrodialysis, improving treatment performance. The objective is to produce two streams: a nutrient-rich stream suitable for recovery, and a diluted stream meeting discharge regulations. Short-term experiments were conducted under varying currents and applied voltages, aiming to determine the best operating conditions. Subsequently, long-term experiments were conducted to assess operational stability, and overall system performance. Results indicated that 0.1A and 7.5V were the best values for galvanostatic and potentiostatic mode. Moreover, long-term tests demonstrated that electrodialysis effectively concentrated nitrogen and phosphorus, enabling their recovery, while reducing pollutant load in the effluent. Specifically, in the concentrate up to 952.35 mg NH4-N/L and 72.44 mg PO4-P/L at 0.1A and 856.04 mg NH4-N/L and 70.05 mg PO4-P/L at 7.5V resulted. Diluted stream meets regulations for nitrogen, obtaining 4.7±0.9 and 3.6±0.5 mg/L at galvanostatic and potentiostatic mode. These findings highlight electrodialysis as a promising and sustainable strategy for nutrient recovery and effluent management in advanced wastewater treatment, although strategies such as multi-stage ED, increasing membrane area, anti-scaling coatings or cleaning protocols are necessary to improve phosphorus removal and ensure compliance with regulatory standards., This research work has been supported by the Spanish Ministry of Science and Innovation by "RECREATE" (PID2020-114315RB-C21/22) and "MEM4REC" (CTM2017-86751-C2-1/2-R) projects, jointly with the European Regional Development Fund (ERDF) , which are gratefully acknowledged. Authors would also like to thank the Vice-Rectorate for Research at the Universitat Politecnica de Valencia (PAID-11-24 and PAID-01-23) and the Vice-Rectorate for Research at the Universitat de Valencia (UV-INV-AE-3673218) for their support.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Integrated Methods in Replenishment Planning Processes

  • Andres, B.|||0000-0002-7920-7711
  • MENGUAL RECUERDA, ANA|||0000-0003-4727-9099
  • Pérez-Molina, Ana Isabel|||0000-0002-1266-7027
  • Pérez Bernabeu, Elena|||0000-0002-9221-7623
[EN] Small and medium-sized enterprises (SMEs) face significant chal-lenges in digitalizing decision-making processes, particularly in demand forecast-ing, replenishment, and production planning. This study investigates the appli-cation of integrated methods in replenishment planning. A set of key hybrid approaches employed in replenishment planning, including deep reinforcement learning, hybrid machine learning forecasting models, and optimization model have been identified. The findings indicate that integrating data-driven models with knowledge-based systems enhances decision-making, optimizes inventory levels, and mitigates procurement risks. Despite the benefits of hybrid approaches, fur-ther research is needed to expand integrated replenishment models, particularly for industries with complex supply chains. Future developments should focus on combining rule-based models with AI-driven predictive analytics to improve replenishment efficiency and adaptability in dynamic markets., The research that led to these findings received funding from the Horizon Europe Framework Programme (HORIZON) with Grant Agreement No. 101177368 Agile Manufacturing as a Service through AI Autonomous Agents (MaaSAI) and with Grant Agreement No. 101177842 Unified Modeling and Automated Scheduling for Manufacturing as a Service (UniMaaS). From Aid for First Research Projects (PAID-06-24) and (PAID-11-24), by the Vicerectorate for Research of the Universitat Politècnica de València (UPV) and from Generalitat Valenciana Grants for doctoral researchers to work in companies in the Valencian Community (CIAEST2024/52).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Secant-Type Iterative Classes for Nonlinear Equations with Multiple Roots

  • Chicharro, Francisco I.|||0000-0001-9116-2870
  • Garrido-Saez, Neus|||0000-0002-7903-8591
  • Jerezano, Julissa H.
[EN] General-purpose iterative methods for solving nonlinear equations provide approximations to solving problems without closed-form solutions. However, these methods lose some properties when the problems have multiple roots or are not differentiable, in which case specific methods are used. However, in most problems the multiplicity of the root is unknown, which reduces the range of methods available to us. In this work we propose two iterative classes with memory for solving multiple-root nonlinear equations without knowing the multiplicity. One of the proposals includes derivatives, but the other is derivative-free, obtained from the previous one using divided differences and a parameter in its iterative expression. The order of convergence of the proposed schemes is analyzed. The stability of the methods is studied using real dynamics, showing the good behavior of the methods. A numerical benchmark confirms the theoretical study., : This research was funded by Ayuda a Primeros Proyectos de Investigación (PAID-06-23) and (PAID-11-24), both from Vicerrectorado de Investigación de la Universitat Politècnica de València (UPV) .
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Predictive ANN Modeling and Optimization of Injection Molding Parameters to Minimize Warpage in Polypropylene Rectangular Parts

  • Gámez Martínez, Juan Luís
  • Jorda-Vilaplana, Amparo
  • Peydro, M. A.|||0000-0002-8503-1505
  • Sellés, M.A.|||0000-0002-0784-5757
  • Sanchez-Caballero, Samuel|||0000-0001-5322-8082
[EN] Injection molding is a fundamental process for transforming plastics into various industrial components. Among the critical aspects studied in this process, volumetric contraction and warpage of plastic parts are of particular importance. Achieving precise control over warpage is crucial for ensuring the production of high-quality components. This research explores optimizing injection process parameters to minimize volumetric contraction and warpage in rectangular polypropylene (PP) parts. The study employs experimental analysis, MoldFlow simulation, and Artificial Neural Network (ANN) modeling. MoldFlow simulation software provides valuable data on warpage, serving as input for the ANN model. Based on the Backpropagation Neural Network algorithm, the optimized ANN model accurately predicts warpage by considering factors such as part thickness, flow path distance, and flow path tangent. The study highlights the importance of accurately setting injection parameters to achieve optimal warpage results. The BPNN-based approach offers a faster and more efficient alternative to computer-aided engineering (CAE) processes for studying warpage., The authors thank the Vicerrectorado de Investigacion de la Universitat Politecnica de Valencia (PAID-11-24).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Light-induced structural rearrangements of axitinib and their role in phototoxic responses

  • El Ouardi, Meryem
  • do Carmo Linhares, Debora
  • Chen, Xiong
  • Hofkens, Johan
  • Miranda, Miguel A.
  • Álvarez-Satizabal, Alejandro|||0000-0002-4045-0642
  • Vayá Pérez, Ignacio|||0000-0003-1682-9342
  • Andreu, Inmaculada|||0000-0003-3409-9443
[EN] Axitinib (AXT) is a second-generation tyrosine kinase inhibitor widely used in advanced renal cell carcinoma and currently explored in light-modulated therapies due to its E/Z photoisomerizable scaffold. Despite its clinical relevance and UVA absorption, the photobiological consequences of its light-induced structural rearrangements remain largely unexplored. Here, we elucidate the mechanistic basis of AXT phototoxicity by integrating photophysical characterization with cellular studies while distinguishing the roles of its (E)- and (Z)-isomers. Steadystate photolysis reveals that (E)-AXT undergoes photodegradation in aqueous media but preferentially isomerizes to (Z)-AXT in lipophilic environments, which is accelerated in the presence of human serum albumin (HSA). Conversely, (Z)-AXT displays medium-dependent photostability, being stabilized by HSA and reverting to the (E)-isomer in aqueous solution. Spectroscopic studies, including laser flash photolysis, support a mechanism involving tautomerization through excited-state intramolecular proton transfer and transient radical intermediates, consistent with predominant Type I photosensitization. Notably, (Z)-AXT is favored in lipophilic and protein-rich environments, likely through intramolecular hydrogen-bond stabilization of its 2H-tautomer. Cellular studies in keratinocytes revealed two complementary phototoxic pathways: photoinduced conversion of cytotoxic (Z)-AXT from (E)-AXT and the intrinsic phototoxicity of (Z)-AXT under irradiation. Although both isomers cause similar protein oxidation, (Z)-AXT is the main contributor due to its higher stability with HSA. While alkaline comet assays detected no direct DNA strand breaks, gamma-H2AX immunostaining revealed lightinduced DNA double-strand breaks. Overall, these findings identify (Z)-AXT as a previously unrecognized phototoxic species and establish a framework linking isomerization, microenvironmental stabilization, and Type I photosensitization in kinase inhibitors., Financial support from the Vicerrectorado de Investigacion of the Universitat Politecnica de Valencia (PAID-11-24) and the FPU predoctoral fellowship (FPU19/02201) from the Spanish Ministry awarded to M. El O. is gratefully acknowledged. We also thank Generalitat Valenciana for support through the Santiago Grisolia program (CIGRIS/2023/130), which enabled the contract of A. A.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Scale matters: A 3 scope urban carbon footprint accounting at the neighborhood level

  • Roncero-Tarazona, Mireia
  • Ribó-Pérez, David Gabriel|||0000-0003-1089-5197
  • Martinez-Rodriguez, Lucas Rodolfo
  • Montagud- Montalvá, Carla|||0000-0002-7118-6119
  • Gómez-Navarro, Tomás|||0000-0001-6114-2414
  • Gil-Chong, P.
[EN] Urban areas contribute over 70% of global greenhouse gas emissions, yet city-wide approaches often fail to address the complexities within diverse urban environments. This study presents a methodological framework for calculating neighborhood-level carbon footprints, incorporating Scopes 1, 2, and 3 emissions from key sectors: energy, transport, waste, goods consumption, and construction. Applying this framework to Valencia, Spain, reveals significant intra-urban disparities. Outer neighborhoods exhibit high transport-related emissions due to reliance on private vehicles, yet possess substantial carbon sequestration potential from green spaces and wetlands. In contrast, central neighborhoods, with higher income levels, display elevated consumption-driven emissions but benefit from pedestrian-friendly infrastructure, reducing transport emissions. The analysis shows that most neighborhoods have annual emissions between 20 to 60 ktCO2e. Nevertheless, 5 neighborhoods (La Punta, Malilla, Benicalap, Russafa and Sant Pau) exceed each one the 80 ktCO2e a year, being responsible of the 18% of annual emissions of the city, emphasizing the need for targeted interventions. This framework enables a first-step diagnostic assessment that guides the identification of critical emission zones and their underlying drivers. Its spatial and sectoral insights can inform further interdisciplinary analyses ¿ including social, economic, or infrastructural factors ¿, supporting more targeted and equitable decarbonization strategies. By addressing localized emission sources and socio-economic disparities, cities can achieve more efficient resource allocation and advance towards carbon neutrality and urban resilience., This work was supported by PURPOSED PID2021-128822OB I00 funded by: MCIN/AEI/10.13039/501100011033/and DESVAB (Descarbonitzar Valencia barri a barri: quadre de comandament de politiques climatiques territorialitzades) funded by Ajuntament de Valencia, "Ayuda Grupos de Investigacion" (PAID-11-24) from the Vicerrectorado de Investigacion de la Universitat Politecnica de Valencia (UPV) . Also this work was supported in part by the Catedra de Transicion Energetica Urbana (Las Naves-FVCiE-UPV).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Assessing urban climate actions: A quantitative pathway to decarbonisation

  • Roncero-Tarazona, Mireia
  • Ribó-Pérez, David Gabriel|||0000-0003-1089-5197
  • Gómez-Navarro, Tomás|||0000-0001-6114-2414
  • Crespo-Montañés, C.
  • Pineda-Soler, J.
  • Gomar-Pascual, Júlia
[EN] This study presents a spatially explicit, scenario-based framework to assess the greenhouse gas mitigation potential of neighbourhood-scale urban climate actions across multiple sectors. Applied to the city of Valencia (Spain), the results show that coordinated implementation of a limited set of high-impact actions can reduce city-wide emissions by more than 80% under a moderate policy ambition scenario, assuming partial (50%) implementation of mitigation actions and electricity grid decarbonisation aligned with national plans. Mitigation potential is unevenly distributed across neighbourhoods, reflecting differences in urban morphology, energy demand, and mobility patterns. Sensitivity analysis highlights strong dependence of electrification-based actions on electricity grid decarbonisation, while demand and mobility driven measures remain more stable. The framework supports spatially differentiated, evidence-based urban decarbonisation strategies., This work was supported by DESVAB (Descarbonitzar Valencia barri a barri: quadre de comandament de politiques climatiques territorialitzades) funded by Ajuntament de Valencia. Also this work was supported in part by the Catedra de Transicion Energetica Urbana (Las Naves-FVCiE-UPV) and "Ayuda Grupos de Investigacion" (PAID-11-24) from the Vicerrectorado de Investigacion de la Universitat Politecnica de Valencia (UPV).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Stability Analysis and Local Convergence of a New Fourth-Order Optimal Jarratt-Type Iterative Scheme

  • Martínez Molada, Eulalia|||0000-0003-2869-4334
  • Cordero Barbero, Alicia|||0000-0002-7462-9173
  • Torregrosa Sánchez, Juan Ramón|||0000-0002-9893-0761
  • Reyes, José A.
[EN] In this work, using the weight function technique, we introduce a new family of fourth-order iterative methods optimal in the sense of Kung and Traub for scalar equations, generalizing Jarratt's method. Through Taylor series expansions, we confirm that all members of this family achieve fourth-order convergence when derivatives up to the fourth order are bounded. Additionally, a stability analysis is performed on quadratic polynomials using complex discrete dynamics, enabling differentiation among the methods based on their stability. To demonstrate practical applicability, a numerical example illustrates the effectiveness of the proposed family. Extending our findings to Banach spaces, we conduct local convergence analyses on a specific subfamily containing Jarratt's method, requiring only boundedness of the first derivative. This significantly broadens the method's applicability to more general spaces and reduces constraints on higher-order derivatives. Finally, additional examples validate the existence and uniqueness of approximate solutions in Banach spaces, provided the initial estimate lies within the locally determined convergence radius obtained using majorizing functions., This research was funded by PAID-11-24 Vicerrectorado de Investigacion de la Universitat Politecnica de Valencia, (UPV).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Technological Innovation and Sustainability in Textile SMEs: A Strategy for the Future

  • Naranjo, Israel
  • Torre-Martínez, María Rocío de la|||0000-0002-8662-8901
  • Cuenca, L.|||0000-0003-3589-4182
  • Boza, Andres|||0000-0002-5429-0416
[EN] Sustainable development is a crucial issue for the improvement of the produc-tion environments of textile SMEs, as it is important for this sector to adopt environmentally responsible production practices. This article analyzes the technologies that strengthen different sustainable practices identified in the lit-erature, around products, processes and the organization. Blockchain, artificial intelligence and the internet of things are the technologies most frequently mentioned in the research, while the sustainable practices that stand out the most are circular economy, product life cycle analysis and the transformation to sustainable business models. Finally, a bibliographic base is provided to ex-plore different technologies and their contribution to environmental, social and economic sustainability.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Calidad del dato en entornos regulados: una propuesta metodológica para la selección de herramientas tecnológicas, Data quality in regulated environments: a methodological proposal for the selection of technological tools

  • Cuenca, L.|||0000-0003-3589-4182
  • Boza, Andres|||0000-0002-5429-0416
  • Maté, Jorge
[EN] In the current context of big data and digital transformation, data quality management (DQM) has become an essential function, especially in environments regulated by legislation such as the GDPR or the EU Artificial Intelligence Act. This article examines the main applicable regulatory frameworks and technical standards, analyzes the data lifecycle, and evaluates commercial tools for data management. Finally, it proposes a methodology for selecting data quality technology tools, integrating regulatory, technical, and organizational aspects, with the aim of facilitating informed decision-making and regulatory compliance., Esta investigación ha sido financiada por el Vicerrectorado de Investigación de la Universitat Politècnica de Valencia (PAID-11-24) y (POLISABIO2024_AP15).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Data-Driven and Knowledge-Based Methods for Strategic Decision-Making in Supply Chain Management

  • Mojica, Ana
  • Andres, B.|||0000-0002-7920-7711
  • Torre-Martínez, María Rocío de la|||0000-0002-8662-8901
[EN] The COVID-19 pandemic underscored the importance of resilient supply chains (SC), leading to research on Artificial Intelligence (AI) in disruption detection and contingency planning. AI enhances data analysis, demand forecasting, and resource optimization, improving SC efficiency, resilience, and sustainability. This study presents a literature review aimed at identifying the current trends in the use of AI data-driven methods, knowledge-based methods, and hybrid methods that combine both, to support strategic decision-making within the supply chain management, such as, supplier selection, network design, capacity definition, or risk management. The objective is to define a conceptual framework that supports determining which methods are most used to support each of the strategic decisions, so that can be applied to enable robust and informed decision-making in supply chain management., The research leading to these results received funding from the Vicerrectorado de Investigación of the Universitat Politècnica de València (PAID-11-24), from the Horizon Europe Framework Programme (HORIZON) with Grant Agreement No. 101177368 Agile Manufacturing as a Service through AI Autonomous Agents (MaaSAI) and also with Grant Agreement No. 101147855 Intelligent and Sustainable Building Management powered by Cross-Sectoral Lifecycle (DATAWiSE).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Machine Learning-Based Method for LOS/NLOS Identification in V2V Environment

  • Chakkour, Yousra
  • Fernández, Herman
  • Rodrigo Peñarrocha, Vicent Miquel|||0000-0002-8075-4851
  • Rubio Arjona, Lorenzo|||0000-0003-3882-4673
  • Reig, Juan|||0000-0003-4541-9326
[EN] Accurate identification of line-of-sight (LOS) and non-line-of-sight (NLOS) conditions is a critical challenge in wireless communication, particularly the vehicle-to-vehicle (V2V) channels, owing to the high dynamics inherent to V2V environments. This study explores the use of machine learning (ML) techniques for LOS/NLOS classification based on wireless channel features extracted from both the measured received power level and the difference between the measured attenuation and free space loss (FSL). Feature correlation, importance analysis, and cumulative scoring are applied to derive a compact and informative feature set. A performance analysis with varying numbers of input features, along with an ablation study, showed that reliable classification can be maintained even with a reduced feature set. In addition, per-class evaluation is performed to capture distinct LOS and NLOS behaviors, which is particularly relevant when prioritizing specific outcomes such as minimizing false LOS or false NLOS detection. Balanced datasets were created through random sampling from the LOS and NLOS classes, with training and testing performed using K-fold cross-validation (CV). Three models, random forest (RF), support vector machines (SVM), and LogitBoost, were evaluated based on recall, specificity, precision, and the F1-score metric. The results indicate that the RF model outperforms the others and that a minimal yet balanced training dataset from both the LOS and NLOS classes is sufficient to achieve high classification reliability. The proposed method offers interpretability, a low computational load framework, and flexibility to address specific classification needs. This aspect provides valuable insights into improving the performance of vehicular communication systems., This work was supported in part by the Vicerrectorado de Investigación de la Universitat Politècnica de València under Grant PAID-11-24, and in part by MCIN/AEI/10.13039/501100011033 through the I+D+i Projects under Grant PID2024-158965OB-C21.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Derivative-free optimal multiple-root finding family of iterative methods

  • Jerezano, Julissa H.
  • Chicharro, Francisco I.|||0000-0001-9116-2870
  • Garrido-Saez, Neus|||0000-0002-7903-8591
[EN] A new family of iterative methods for finding multiple roots of nonlinear problems is proposed. The family is derivative-free and optimal in the sense of Kung-Traub's conjecture. The two-step family includes a weight function. The stability analysis uses two different weight functions: a polynomial and a rational function. Furthermore, a numerical benchmark is carried out on these two weight functions, showing the competitiveness concerning similar methods in the literature., Open Access funding provided thanks to the CRUE-CSIC agreement with Springer Nature. Francisco I. Chicharro and Neus Garrido-Saez have been partially funded with grants Ayuda a Primeros Proyectos de Investigación (PAID-06-23) and (PAID-11-24), both from Vicerrectorado de Investigación de la Universitat Politècnica de València (UPV) .
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Enhancing Cultural Heritage Engagement with Novel Interactive Extended-Reality Multisensory System

  • Muñoz García, Adolfo|||0000-0003-2435-3348
  • Climent-Ferrer, Juan José|||0000-0003-4130-6439
  • Martí Testón, Ana|||0000-0002-5058-2868
  • Solanes, J. Ernesto|||0000-0001-5011-4872
  • Gracia Calandin, Luis Ignacio|||0000-0001-9258-9286
[EN] Extended-reality (XR) tools are increasingly used to revitalise museum experiences, but typical head-mounted or smartphone solutions tend to fragment audiences and suppress the social dialogue that makes cultural heritage memorable. This article addresses that gap on two fronts. First, it proposes a four-phase design methodology¿spanning artifact selection, narrative framing, tangible-interface fabrication, spatial installation, software integration, validation, and deployment¿that helps curators, designers, and technologists to co-create XR exhibitions in which co-presence, embodied action, and multisensory cues are treated as primary design goals rather than afterthoughts. Second, the paper reports LanternXR, a proof-of-concept built with the methodology: visitors share a 3D-printed replica of the fourteenth-century Virgin of Boixadors while wielding a tracked ¿camera¿ and a candle-like lantern that lets them illuminate, photograph, and annotate the sculpture inside a life-sized Gothic nave rendered on large 4K displays with spatial audio and responsive lighting. To validate the approach, the article presents an analytical synthesis of feedback from curators, museologists, and XR technologists, underscoring the system¿s capacity to foster collaboration, deepen engagement, and broaden accessibility. The findings show how XR can move museum audiences from isolated immersion to collective, multisensory exploration., This work has been funded by the Spanish Government (Grants PID2024-156583OB-I00 and PID2020-117421RB-C21 funded by MCIN/AEI/10.13039/501100011033).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

First optimal vectorial eighth-order iterative scheme for solving non-linear systems

  • Cordero Barbero, Alicia|||0000-0002-7462-9173
  • Torregrosa Sánchez, Juan Ramón|||0000-0002-9893-0761
  • Triguero-Navarro, Paula|||0000-0002-7319-9992
[EN] We introduce a novel iterative method achieving eighth-order convergence, establishing its optimality for solving non-linear systems. A rigorous analysis of convergence order is presented, complemented by investigations into both efficiency indices and the complex dynamics of the proposed method. To assess its performance, extensive numerical experiments are conducted, facilitating comparative analysis with established methods from the literature., This research was partially supported by Vicerrectorado de Investigacion de la Universitat Politecnica de Valencia (PAID-11-24) and funded by the European Research Council (ERC) via Horizon Europe Advanced Grant, grant agreement no 101097688 ("PeroSpiker").