Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 10
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Estimation of the in-plane ultimate stress of lamellar tissue as a function of bone mineral density and osteocyte lacunae porosity

  • Vercher Martínez, Ana|||0000-0003-3695-6461
  • Megías-Díaz, Raquel|||0000-0002-1698-7108
  • Belda Ricardo|||0000-0003-3913-5773
  • Giner Maravilla, Eugenio|||0000-0003-1903-6495
  • Vargas, Pablo
[EN] Detailed finite element models based on medical images (𝜇-CT) are commonly used to analyze the mechanical behavior of bone at microscale. In order to simulate the tissue failure onset, isotropic failure criteria of lamellar tissue are often used, despite its non-isotropic and heterogeneous nature. The main goal of the present work is to estimate the in-plane ultimate stress of lamellar bone, considering the influence of mineral content and the porosity due to the osteocyte lacunae concentration. To this aim, a representative volume cell of lamellar tissue is modeled numerically, including: (1) non-isotropic elastic properties of tissue as a function of the bone mineral density and (2) explicit modeling of the osteocyte lacunae, considering the range of porosity content, size and orientation of ellipsoid-shaped lacunae. Firstly, the element size for the finite element models have been defined from a preliminary convergence analysis. Bounds on the ultimate stress of non-porous lamellar tissue are estimated for two values of bone mineral density, considering the results of tensile and compressive tests of wet osteons from the literature. Subsequently, the ultimate stress of lamellar tissue considering several values of micro-porosity is addressed. Results: Results obtained in this work show that the strength of lamellar bone decreases exponentially with the increase of lacunae porosity concentration. Ultimate stress of non-porous tissue (𝑝 = 0%) increases with high mineral content, reaching a value of ̄ 𝑆 𝑐 𝑡𝑟𝑎𝑛𝑠 = 355.40 ± 39.80 MPa for compression in the transversal direction of the fiber bundles, being BMD = 1.246 g/cm3. The mean value for the longitudinal to transverse strength ratio evaluated for porosity 𝑝 = 0%, 1% and 5% and a mineral content BMD = 1.2 g/cm3, is 2.47:1 for tension and 1.55:1 for compression. These values are in agreement with literature. Conclusions: Osteocyte lacunae act as stress concentrators, acting as potential stimulus for the bone regeneration process. A novel micromechanical model for the in-plane ultimate stress of lamellar tissue as a function of mineral content and lacunae concentration is presented. Additional considerations about the intralamellar shear stress evolution are also given, The authors acknowledge the Ministerio de Ciencia e Innovación y Universidades and the European Regional Development Fund (FEDER) for the financial support received through the projects PID2020- 118920RB-I00 and PID2020-118480RB-C21 and C22 funded by MCIN/AEI/10.13039/501100011033 and by ERDF A way of making Europe , the Ministerio de Ciencia e Innovación y Universidades MCIN/AEI/ 10.13039/501100011033 and Europe Union NextGenerationEU/PRTR for the projects PDC2021-121368-C21 and C22, and the Generalitat Valenciana for Programa PROMETEO/2021/046
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Design and mechanics of stackable auxetic S-shaped structures

  • Rufo-Martin, Celia
  • Diaz-Alvarez, Jose
  • Miguelez, Maria Henar
  • Youssef, George
  • Infante-García, Diego|||0000-0001-6010-2031
[EN] The emerging auxetic lattices, driven by contemporary advancements in additive manufacturing, have garnered significant attention, with an emphasis on improving structural performance and energy absorption efficiencies while mitigating the contributions of material nonlinearities and instabilities. This research advances the state of the art of thin-strut auxetic structures by introducing a stacking schema to realize 3D S-shaped polystructures with rigid-body motion-dominated deformation, spatial symmetry, and persistent auxeticity. Several generations of these polystructures were 3D printed using vat photopolymerization with varying strut thickness ranging from 1 mm to 3 mm. The additively manufactured structures were mechanically tested under quasi-static and impact loading scenarios, providing physical evidence for the foreseen structural behaviors discussed above. The polystructures yielded load-bearing-to-mass ratios of 4.6 kN/kg, 7.6 kN/kg, and 12.3 kN/kg for t1, t2, and t3, respectively, with less than 10 g of weight, a result of the rigid body motion and the asymmetric rotation of the polystructure beams. Additionally, the impact response highlighted a structure-to-material transition, resulting in similar force maxima for t1 and t2, with 9 and 10 N (structure-dominated), whereas t3 reported a force of up to 49 N (material-dominated). However, irrespective of the strut thickness, the negative Poisson's ratio remained nearly unchanged (-0.22 +/- 0.02), exemplifying the importance of the structural mechanics substantiated by the specific topological design of S-shaped unit cells. The research findings paved the way for the translational potential of S-shaped polystructures in practical applications for mitigating impact, including civilian and military loading conditions., The authors acknowledge the support of the National Science Foundation under Grant No. 2035663 (G.Y.) . Funding from the U.S. Department of Defense (W911NF1410039, W911NF1810477, W911NF2310150, and N00174-23-1-0009) is also acknowledged. The authors are also grateful for internal funding from San Diego State University and Universidad Carlos III de Madrid. In particular, this work was supported by the MCIN/AEI/10.13039/501100011033 and "European Union NextGenerationEU/PRTR" under grant PDC2021-121368-C21; the MCIN/AEI/10.13039/501100011033 under grants PID2020-112628RA-I00 and PID2020-118480RB-C22.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Influence of material extrusion parameters on fracture mechanisms of polylactic acid under three-point bending

  • Álvarez-Blanco, Mario
  • Arias-Blanco, Adrián
  • Marco, Miguel
  • Miguélez, María Henar
  • Infante-García, Diego|||0000-0001-6010-2031
  • Giner Maravilla, Eugenio|||0000-0003-1903-6495
[EN] In this work, a thorough fracture assessment of additive manufactured specimens made by 3D printed polylactic acid (PLA) under three-point bending is presented. This polymer is widely used in additive manufacturing for numerous applications, gaining prominence in fields such as biomechanics. Prismatic fully dense specimens and lattice structure specimens with different raster orientations and densities were fabricated using the material extrusion-based additive manufacturing technique. The objective is to analyse the effect of relevant process parameters on the fracture mechanism of short beam specimens tested under three-point bending. Digital image correlation and computed tomography have been used to measure the full field displacement and internal defects, respectively. Furthermore, the theory of critical distances was applied to assess the mechanical strength of lattice structure specimens. The results have shown the strong influence of raster orientation on the mechanical strength and fracture patterns even for negative air gap values. The transition from brittle to ductile failure was observed when changing density and raster orientation. Lastly, neck-shaped defects were detected in knots of specimens manufactured with a grid pattern. Defects in grid pattern specimens appear due to the prescribed path followed by the extruder during the building process. They were the main source causing a decrease in the mechanical strength and fracture trajectories. The objective of this research is to enhance the knowledge on the mechanical response of 3D printed components and to give an in-depth failure assessment., The authors gratefully acknowledge the funding support received from the Spanish Ministerio de Ciencia e Innovacion for funding the projects PID2020-112628RA-I00 and PID2020-118480RB-C21, -C22, MCIN/AEI / 10.13039/501100011033 and by "ERDF A way of making Europe"; project PDC2021-121368-C21 and C22 funded by MCIN/AEI/ 10.13039/501100011033 and by the "European Union NextGenerationEU/PRTR". The authors also thank the funding received from Madrid Community (Spain) through the project IND2020/IND-17413. The financial support of Generalitat Valenciana and European Social Fund through Programme PROMETEO 2021/046 and CIAPOS/2021/271 is also acknowledged. Lastly, the Universitat Politecnica de Valencia is acknowledged for the financial support through PAID-PD-22.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Experimental and numerical analysis of the influence of intramedullary nail position on the cut-out phenomenon

  • Arias-Blanco, A.
  • Marco, M.
  • Larraínzar-Garijo, R.
  • Miguélez, M. H.
  • Giner Maravilla, Eugenio|||0000-0003-1903-6495
[EN] Background and objective: Proximal femur fractures, colloquially known as hip fractures, are a common pathology with increasing incidence in the last years due to the enhanced ageing population. Regarding the extracapsular fracture, the treatment for this pathology consists of a fixation of the fragments using an osteosynthesis device, mainly the intramedullary nail. This repairing method implies several complications, which may include the failure of the fixation device, frequently occurring due to the "cut-out" mechanism. The present work focuses on the study of how the position of the cephalic screw, which should be fixed during surgery, affects the cut-out risk. Through experimental tests and numerical models some variables that can be critical for the cut-out phenomenon are analysed. Methods: This study has been carried out through a numerical model based on the finite element method and experimental tests. The digital image correlation technique has been used in experimental tests to measure displacements on the femoral surface with the objective of numerical model validation. Some basic daily activities with different intramedullary nail positions have been analysed through the numerical model, considering variables that can induce the cut-out complication. Results: The results show how the intramedullary nail position clearly influences the cut-out risk, showing that displacements in the upper, anterior and posterior direction increase the cut-out risk, while displacement in the lower direction endangers the intramedullary nail itself. Thus, the centred position is the one which reduces the cut-out risk. Conclusions: This work supposes an improvement in the knowledge of the cut-out phenomenon thanks to the combination of experimental testing and validated numerical models. The effects of different intramedullary nail positions in the femoral head are studied, including a novelty variable as torque, which is critical for the structural integrity of the fixation. The main conclusion of the work is the determination of the central intramedullary nail position as the most favourable one for decreasing the cut-out risk., The authors gratefully acknowledge the funding support received from the Spanish Ministry of Science and Innovation for funding project PID2020-112628RA-I00/AEI/10.13039/501100011033, projects PID2020-118480RB-C21 and -C22 and from the Madrid Community (Spain) through the project IND2020/IND-17413. The financial support of the European Union NextGenerationEU/PRTR through grant number PDC2021-121368-C21 and -C22 and the Generalitat Valenciana through Programme PROMETEO 2021/046 is also acknowledged.& nbsp;
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Aplicación de termografía infrarroja en la estimación de la vida a fatiga en laminados de CFRP taladrados.

  • Calvo, Jose Vicente|||0000-0001-8488-1762
  • Feito-Sánchez, Norberto|||0000-0001-7330-6404
  • Giner Maravilla, Eugenio|||0000-0003-1903-6495
  • Miguélez, María Henar
[ES] La aplicación de técnicas no destructivas para evaluar materiales compuestos sometidos a fatiga es un área de creciente interés entre la comunidad científica. Entre las técnicas disponibles, destaca el uso de la termografía infrarroja debido a su asequibilidad, simplicidad y resultados prometedores en investigaciones previas. En este estudio, se aplica la termografía infrarroja con el objetivo de obtener modelos predictivos capaces de estimar el límite de fatiga de laminados gruesos de CFRP (polímero reforzado con fibra de carbono) sometidos a cargas de tracción. Los ensayos experimentales conllevan la monitorización de la temperatura en laminados con características típicas de la industria aeroespacial, a través de una cámara termográfica. La campaña experimental implica la variación de los niveles de daño por taladrado y las cargas cíclicas de tracción. Con los datos obtenidos de la evolución de la temperatura durante la fase inicial de los ensayos de fatiga se obtienen modelos analíticos predictivos del límite de fatiga. Los resultados indican que el modelo propuesto es capaz de predecir de manera eficiente el límite de fatiga con una alta fiabilidad, mostrando una sólida correlación entre las predicciones y los resultados experimentales, por lo que este estudio subraya la utilidad de las técnicas termográficas para evaluar el daño y predecir el límite de fatiga de laminados CFRP en diversas condiciones de carga, Los autores agradecen la financiación a través de los siguientes proyectos: PID2020-118480RB-C21 y C22, financiado por MCIN/AEI/ 10.13039/501100011033 y por FEDER Una manera de hacer Europa ; proyecto PDC2021-121368-C21 y C22 financiado por MCIN/AEI/ 10.13039/501100011033 y por la Unión Europea NextGenerationEU/PRTR ; ayuda PRE2018-086277 financiada por MCIN/AEI/10.13039 /501100011033 y por FSE Invierte en tu futuro . También agradecen la financiación de la Generalitat Valenciana, programa PROMETEO 2021/046 y el proyecto GV/2021/060.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Contribución de congreso (ConferenceOutput)

Estudio de la fractura a compresión de hueso trabecular sano, osteoporótico y artrósico procedente de cabezas femorales humanas

  • Megías-Díaz, Raquel|||0000-0002-1698-7108
  • Belda Ricardo|||0000-0003-3913-5773
  • Vercher Martínez, Ana|||0000-0003-3695-6461
  • Giner Maravilla, Eugenio|||0000-0003-1903-6495
[ES] En este trabajo se ha estudiado el comportamiento mecánico del hueso trabecular mediante ensayos experimentales de compresión y el desarrollo de modelos numéricos de elementos finitos. Las muestras proceden de cabezas femorales humanas y se agruparon en tres cohortes: grupo sano (GS), grupo osteoporótico (GO) y grupo artrósico (GA). Los especímenes se ensayaron en la dirección estimada de máxima rigidez y se sometieron a cargas de compresión cuasiestática hasta la fractura. La respuesta experimental permitió calibrar los modelos numéricos, estimando el módulo de Young del tejido óseo y las propiedades de fallo de las muestras. Los resultados muestran que el hueso sano soporta un 52% más de carga que el hueso osteoporótico, y que la deformación correspondiente a la tensión máxima es un 33% mayor en el GS que en el GO. Las muestras artrósicas presentan un comportamiento intermedio, más próximo al grupo osteoporótico que al sano, lo que indica que las patologías analizadas se asocian a menores niveles de carga y deformación frente al hueso sano. La calibración de los modelos numéricos proporciona valores similares de deformación de inicio de fallo y de fallo completo para las muestras patológicas, mientras que en las muestras sanas estos valores difieren. En consecuencia, la simulación de la fractura en hueso osteoporótico requiere considerar propiedades de fallo específicas, coherentes con un comportamiento más frágil que el del hueso sano. Finalmente, este trabajo permite cuantificar dichos parámetros e identifica como principal origen de las diferencias las características morfométricas propias de la microestructura del hueso trabecular no sano., Los autores desean agradecer la financiación recibida desde la GVA por el Plan FDEGENT 2018 GVA y por el programa PROMETEO 2021/046, y por los proyectos PID2020-118920RB-I00 y PID2020-118480RB-C21 y C22, financiado por MCIN/AEI/10.13039/501100011033 y por FEDER Una manera de hacer Europa y el proyecto PDC2021-121368-C21 y C22 financiado por MCIN/AEI/10.13039/501100011033 y por la Unión Europea NextGenerationEU/PRTR .
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Printable and Tunable Bioresin with Strategically Decorated Molecular Structures

  • Rufo-Martín, Celia
  • Díaz-Álvarez, José
  • Miguélez, Henar
  • Youssef, George
  • Infante-García, Diego|||0000-0001-6010-2031
[EN] As personalized medicine rapidly evolves, there is a critical demand for advanced biocompatible materials surpassing current additive manufacturing capabilities. This study presents a novel printable bioresin engineered with tunable mechanical, thermal, and biocompatibility properties through strategic molecular modifications. The study introduces a new bioresin comprising methyl methacrylate (MMA), ethylene glycol dimethacrylate (EGDMA), and a photoinitiator, which is further enhanced by incorporating high molecular weight polymethyl methacrylate (PMMA) to improve biostability and mechanical performance. The integration of printable PMMA presents several synthesis and processing challenges, necessitating substantial modifications to the 3D printing process. Additionally, the bioresin is functionalized with antibacterial silver oxide and bone-growth-promoting hydroxyapatite at various weight ratios to extend its application further. The results demonstrate the agile printability of the novel bioresin and its potential for transformative impact in biomedical applications, offering a versatile material platform for additive manufacturing-enabled personalized medicine. This work highlights the adaptability of the novel printable bioresin for real-life applications and its capacity for multiscale structural tailoring, potentially achieving properties comparable to native tissues and extending beyond conventional additive manufacturing techniques., The authors acknowledge the support of the National Science Foundation under Grant No. 2035663. The authors are also grateful for internal funding from San Diego State University. Funding from the United States Department of Defense (W911NF1410039, W911NF1810477, W911NF2310150, and N00174-23-1-0009) is also acknowledged. Additionally, this work was supported by the MCIN/AEI/10.13039/501100011033 and "European Union NextGenerationEU/PRTR" under grant PDC2021-121368-C21; the MCIN/AEI/10.13039/501100011033 under grants PID2020-112628RA-I00 and PID2020-118480RB-C22; and by the Generalitat Valenciana under grant CIAPOS/2021/271.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Influence of distributed out-of-plane waviness defects on the mechanical behavior of CFRP laminates

  • Calvo, Jose Vicente|||0000-0001-8488-1762
  • Quiñonero-Moya, Antonio Ramón|||0000-0002-2370-7960
  • Feito-Sánchez, Norberto|||0000-0001-7330-6404
  • Giner Maravilla, Eugenio|||0000-0003-1903-6495
  • Miguélez, María Henar
[EN] One of the most common defects induced during manufacturing of laminates is out-of-plane fibre waviness. This defect significantly affects the mechanical behavior of the laminate and reduces fatigue life and the load capacity of the material. Therefore, it is important to understand the impact of fibre waviness on the performance of composite laminates. In this work, multiple out-of-plane waves have been introduced throughout a Carbon Fibre Reinforced Polymer (CFRP) laminate at different thickness positions. The specimens were tested under tensile loading and an analysis of the surface of the laminate has been carried out by means of Digital Image Correlation (DIC). The results obtained by DIC were able to predict the apparent strain of the laminate quite accurately, as well as locate up to seven undulations at different depths. It was proved that a laminate with multiple wrinkles has 16% less tensile load strength. The results were used to validate different Finite Element (FE) models of the laminate showing a good agreement. These simple models were able to predict the initiation and propagation of failure in both the matrix and the fibre., This research is part of the R + D + i project PID2020-118480RB-C21 and C22, funded by MCIN/AEI/10.13039/501100011033 and by "ERDF A way of making Europe". Grant PDC2021-121368-C21 and C22 funded by MCIN/AEI/10.13039/501100011033 and by the "European Union NextGenerationEU/PRTR". Grant PRE2018-086277 and PRE2021-097626 funded by MCIN/AEI/10.13039/501100011033 and by "ESF Investing in your future". The funding of the Generalitat Valenciana, Programme PROMETEO 2021/046 and project GV/2021/060, is also acknowledged.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Development, 3D printing, and mechanics of novel auxetic unit cell monostructures

  • Rufo-Martín, Celia
  • Díaz-Álvarez, José
  • Miguélez, María Henar
  • Koohbor, Behrad
  • Youssef, George
  • Infante-García, Diego|||0000-0001-6010-2031
[EN] Complex structures with unique mechanics are pivotal to advancing additive manufacturing, enabling applications where traditional methods are impractical. This study presents a novel 3D auxetic S-shaped monostructure designed for scalability, tunability, and printability using vat photopolymerization. Unit cell geometries were fabricated and experimentally evaluated under quasi-static loading conditions, with full-field analyses providing insights into their structural performance. Benchmarking against common auxetic structures (re-entrant and star topologies) highlighted the superior capabilities of the proposed design. The S-shaped monostructures exhibited geometric insensitivity in their force-displacement responses, with a stiffness of similar to 180 N/m, withstanding large displacements of 11 mm without fracture or self-contact and supporting forces up to 1.8 N (i.e., 95 times their weight) before fully recovering upon unloading. Computational and experimental results demonstrated robust spatial auxeticity, persisting up to 85 % of axial global displacement due to geometry-driven rigid body motion, independent of base material properties. The S-shaped structures achieved superior auxetic performance (nu(maxti) approximate to -0.43) compared to re-entrant (nu(maxti) approximate to -0.30) and star (nu(maxti) approximate to - 0.05) counterparts, with a monotonic and reversible auxetic response throughout loading. Strain contour analyses from digital image correlation validated the reduced stress concentrations and rigid body-dominated mechanism. The exceptional auxeticity and mechanical resilience of the S-shaped monostructures suggest promising applications in advanced designs, including 3D stackable configurations for impact mitigation applications., The authors acknowledge the support of the National Science Foundation under Grant No. 2035663 (G.Y.) and Grant No. 2035660 (B. K.) . The authors are also grateful for internal funding from San Diego State University, Rowan University, and Universidad Carlos III de Madrid. In particular, this work was supported by the MCIN/AEI/10.13039/501100011033 and "European Union NextGenerationEU/PRTR" under grant PDC2021-121368-C21; the MCIN/AEI/10.13039/501100011033 under grants PID2020-112628RA-I00 and PID2020-118480RB-C22. Funding from the U.S. Department of Defense (W911NF1410039, W911NF1810477, W911NF2310150, and N00174-23-1-0009) is also acknowledged.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

The role of the interfaces and cross-links on the mechanical behavior of mineralized collagen fibrils. A numerical approach

  • Vercher-Martínez, Ana
  • Giner, Eugenio
  • Fuenmayor, F. Javier
  • García-Aznar, J. Manuel
Mechanical properties of bone tissue are highly dependent on its hierarchical structure. The presence of microcracks and diffuse damage in lamellar bone is correlated with the failure of the collagen-mineral interface in mineralized collagen fibrils (MCF). The main goal of this work is to evaluate the mechanical behavior of the interfaces and quantify the stiffness loss of the MCF associated with different failure mechanisms, under controlled in-plane displacement. Additionally, we aim to study the role of the cross-links on the fibril mechanical response, beyond the interface failure. Inter- and intra-microfibrilar cross-links are analyzed. In order to address the first issue, a detailed representative volume of the MCF is analyzed by means of the finite element method, under the assumption of plane strain and periodic boundary conditions. In this model the interfaces between constituents are modeled with an exponential cohesive law. Enzymatic cross-links, located at the molecular terminals connecting each 4D ( ) staggered molecules, are represented by non-linear springs. Three in-plane controlled deformations are applied. The results of this work provide the anisotropic stiffness loss of the tissue involved in the different failure mechanisms at the nano-scale length. The initiation of microcracks and the presence of damage zones are compatible with the failure mechanisms observed at interfaces. Interface failure entails a progressive stiffness loss, bringing a non-linear behavior of bone. The strength obtained for the longitudinal maximum deformation is more than 20 times the transverse strength and 3.5 times the shear strength. The quantification of the reduction percentage in the elastic moduli and the shear stiffness when the fibril is damaged, has a potential application in improving failure criteria based on degradation of elastic constants. When longitudinal elongation is applied, the mechanical contribution of the cross-links in delaying the failure initiation of the interface is shown. Likewise, results of this work confirm the scarce influence of the cross-links in the strain range analyzed. Additionally, a three-dimensional numerical model of several microfibrils is defined with the aim of analyzing the mechanical relevance of inter- and intra-microfibrilar cross-links, beyond the interface failure. Results confirm that cross-links transfer the load when strain increases, being highlighted the mechanical competence of the trivalent cross-links.