Pasar al contenido principal

TALADRADO DE COMPONENTES HIBRIDOS CFRPS/TI Y TOLERANCIA AL DAÑO DEBIDO A MECANIZADO DURANTE EL COMPORTAMIENTO EN SERVICIO DE UNIONES ESTRUCTURALES AERONAUTICAS

PRE2018-086277

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal de Promoción del Talento y su Empleabilidad en I+D+i
Subprograma Subprograma Estatal de Formación
Convocatoria Contratos Predoctorales
Año convocatoria 2018
Plan Estatal 2017-2020 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario UNIVERSIDAD CARLOS III DE MADRID

Resultados relacionados

Resultados totales (Incluyendo duplicados): 6
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Rapid fatigue life estimation of drilled CFRP laminates and titanium stacks using thermography

  • Calvo, Jose Vicente|||0000-0001-8488-1762
  • Feito-Sánchez, Norberto|||0000-0001-7330-6404
  • Giner Maravilla, Eugenio|||0000-0003-1903-6495
  • Miguélez, María Henar
[EN] In this work, we estimate the fatigue life of drilled Carbon Fiber Reinforced Polymer (CFRP) laminates making use of the temperature evolution of the component. As the self-heating effect due to cyclic loading causes a temperature change in the initial stages of the loading, the slope of the temperature variation ¿T versus the number of cycles can be used to estimate the remaining life. We have validated the applicability of the procedure for drilled laminates under different cutting conditions, and for drilled Ti-CFRP stacks. Infrared thermography was used to obtain the temperature variation during cycling loading. The results proved that the obtained adjusted model can effectively estimate the fatigue life of CFRP laminates with delamination damage or thermal damage with an error of 15%, proving the usefulness of this methodology for drilled and stacked laminates., This research is part of the R + D + i project PID2020-118480RBC21,-C22, and PID2023-151610OB-C21,-C22, funded by MCIN/AEI/ 10.13039/501100011033 and by ERDF A way of making Europe . Grant PRE2018-086277 funded by MCIN/AEI/10.13039/ 501100011033 and by ESF Investing in your future . The funding of the Generalitat Valenciana, Programme PROMETEO 2021/046 and project GV/2021/060 is also acknowledged.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Impact of drilling operations on the fatigue performance of CFRP and CFRP/Ti hybrid structures using a thermographic approach

  • Calvo, Jose Vicente|||0000-0001-8488-1762
  • Feito-Sánchez, Norberto|||0000-0001-7330-6404
  • Megías-Díaz, Raquel|||0000-0002-1698-7108
  • Giner Maravilla, Eugenio|||0000-0003-1903-6495
  • Miguélez, María Henar
[EN] This study investigates the use of infrared thermography as a non-destructive technique to predict the fatigue life of carbon fiber-reinforced polymer (CFRP) laminates, with and without titanium (Ti) stacking, assessing the impact of drilling-induced damage. Drilling, essential for creating mechanical joints, introduces defects that significantly reduce the fatigue life of CFRP. Several models based on data obtained from infrared thermography were applied. These models rely on different parameters from the temperature curve during the test, such as the initial and final slope, the stable temperature in the second phase, or the total dissipated energy. Using these data, it is possible to estimate the remaining fatigue life or the fatigue limit of the material. The results show that models based on the initial slope of the temperature curve provide accurate estimates with errors close to 10%, while models using the stabilized temperature exhibit errors around 19%. Although final-phase models were less accurate, methods based on total dissipated energy effectively predict fatigue limits. Overall, the study demonstrated an average accuracy of 15% in fatigue life prediction under various damage conditions, validating infrared thermography as an effective tool for structural integrity assessment in industrial applications., Open Access funding provided thanks to the CRUE-CSIC agreement with Springer Nature. This research is part of the R+D+i projects PID2023-151610OB-C21 and PID2023-151610OB-C22, funded by MCIN/AEI/10.13039/501100011033 and by ERDF: A way of making Europe. Grant PRE2018-086277 funded by MCIN/ AEI/10.13039/501100011033 and by ESF Investing in your future.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

A simplified fatigue characterization of defective CFRP laminates with infrared thermography

  • Calvo, Jose Vicente|||0000-0001-8488-1762
  • Feito-Sánchez, Norberto|||0000-0001-7330-6404
  • Giner Maravilla, Eugenio|||0000-0003-1903-6495
[EN] Fiber misalignment and out-of-plane waviness are defects encountered in composite material laminates. These defects are particularly prone to occur when adapting the laminate to angular or complex geometries. Using these defective laminates in aerospace applications can undermine their structural integrity and impact their mechanical properties. This work involves a study of applying infrared thermography techniques to estimate the fatigue limit based on the energy dissipated during tensile testing. Defect-free CFRP laminates and laminates with several out-of-plane waviness distributed along the sample and through the thickness are tested at various stress levels. Estimation of their fatigue limit using thermography is performed, and the results show a significant agreement to those obtained through S-N curves, with less than 2% error for defect-free specimens and 13% for defective ones. A reduction in mechanical properties and service life is observed in the material with defects compared to defect-free material, with a decrease of 16% of the ultimate strength and 40% of the fatigue limit. The study supports the application of thermography as a simple and rapid technique to detect and locate this type of defect and characterize the fatigue limit of the CFRP laminate., This research is part of the R+D+i project PID2023-151610OB-C22, funded by MCIN/AEI/10.13039/501100011033 and by "ERDF: A way of making Europe". Grant PRE2018-086277 funded by MCIN/AEI/10.13039/501100011033 and by "ESF Investing in your future". The funding of the Generalitat Valenciana, Programme PROMETEO 2021/046, and project GV/2021/060, is also acknowledged.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Influence of distributed out-of-plane waviness defects on the mechanical behavior of CFRP laminates

  • Calvo, Jose Vicente|||0000-0001-8488-1762
  • Quiñonero-Moya, Antonio Ramón|||0000-0002-2370-7960
  • Feito-Sánchez, Norberto|||0000-0001-7330-6404
  • Giner Maravilla, Eugenio|||0000-0003-1903-6495
  • Miguélez, María Henar
[EN] One of the most common defects induced during manufacturing of laminates is out-of-plane fibre waviness. This defect significantly affects the mechanical behavior of the laminate and reduces fatigue life and the load capacity of the material. Therefore, it is important to understand the impact of fibre waviness on the performance of composite laminates. In this work, multiple out-of-plane waves have been introduced throughout a Carbon Fibre Reinforced Polymer (CFRP) laminate at different thickness positions. The specimens were tested under tensile loading and an analysis of the surface of the laminate has been carried out by means of Digital Image Correlation (DIC). The results obtained by DIC were able to predict the apparent strain of the laminate quite accurately, as well as locate up to seven undulations at different depths. It was proved that a laminate with multiple wrinkles has 16% less tensile load strength. The results were used to validate different Finite Element (FE) models of the laminate showing a good agreement. These simple models were able to predict the initiation and propagation of failure in both the matrix and the fibre., This research is part of the R + D + i project PID2020-118480RB-C21 and C22, funded by MCIN/AEI/10.13039/501100011033 and by "ERDF A way of making Europe". Grant PDC2021-121368-C21 and C22 funded by MCIN/AEI/10.13039/501100011033 and by the "European Union NextGenerationEU/PRTR". Grant PRE2018-086277 and PRE2021-097626 funded by MCIN/AEI/10.13039/501100011033 and by "ESF Investing in your future". The funding of the Generalitat Valenciana, Programme PROMETEO 2021/046 and project GV/2021/060, is also acknowledged.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Análisis de la progresión del daño en laminados compuestos con concentrador de tensiones bajo cargas de tracción

  • Calvo, Jose Vicente|||0000-0001-8488-1762
  • Feito-Sánchez, Norberto|||0000-0001-7330-6404
  • Megías-Díaz, Raquel|||0000-0002-1698-7108
  • Giner Maravilla, Eugenio|||0000-0003-1903-6495
  • Miguélez, María Henar
[ES] En este trabajo se analiza el comportamiento de un laminado grueso de CFRP multidireccional típico de componentes aeroespaciales bajo cargas de tracción cuasiestática. Para realizar este estudio se utilizó la técnica no destructiva de correlación digital de imágenes (DIC). El objetivo es caracterizar la influencia de un concentrador de tensiones a través de la distribución de deformaciones durante los ensayos cuasiestáticos. Los ensayos de tracción mostraron que la distribución de deformaciones alrededor del agujero es capaz de predecir el inicio y la progresión de la grieta en las capas externas. Finalmente, las pruebas experimentales se simularon numéricamente mediante el método de elementos finitos, mostrando una buena concondarncia entre los resultados numéricos y experimentales, y obteniendo así información de las capas más internas., Los autores agradecen el material proporcionado por AIRBUS DEFENCE AND SPACE y al Ministerio de Economía y Competitividad de España por la financiación, dentro del marco del proyecto DPI2017-89197-C2-1-R y DPI2017-89197-C2-2-R y el subprograma asociado de ayudas FPI con referencia PRE2018-086277.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Modeling the delamination failure under compressive loads in CFRP laminates based on digital image correlation analysis

  • Calvo, Jose Vicente|||0000-0001-8488-1762
  • Feito-Sánchez, Norberto|||0000-0001-7330-6404
  • Giner Maravilla, Eugenio|||0000-0003-1903-6495
  • Miguélez, María Henar
[EN] Laminate composite materials such as CFRPs are highly susceptible to delamination, being one of the common failure modes in composite laminates. The combination of severe delamination with uniaxial compressive loads leads to the loss of stability and structure failure. In this study, the authors present an experimental and numerical analysis of this effect in laminates. A series of tests were carried out with four different specimens including delamination-free plates and plates with incipient delamination with different damage size and location. 3D Digital Imagen Correlation technique was applied to predict the buckling initiation and propagation and to validate the numerical models implemented, showing good agreement between the numerical and experimental results. Model material failure includes Hashin criterion and cohesive zone model (CZM) to predict delamination. Finally, numerical models have been used to predict the crack initiation and progression in the rest of samples., This research was funded by the FEDER programme and the Spanish Ministry of Science and Innovation, under projects DPI2017-89197-C2-1-R, DPI2017-89197-C2-2-R, PID2020-118480RB-C21, PID2020-118480RB-C22 and the associated predoctoral subprogram PRE2018-086277. The funding of the Generalitat Valenciana, Programme PROMETEO 2021/046 and project GV 2021/156, is also acknowledged.