Pasar al contenido principal

EVALUACION EXPERIMENTAL Y SIMULACION DEL COMPORTAMIENTO MECANICO A PEQUEÑA ESCALA DE COMPOSITES CERAMICOS

PID2021-126614OB-I00

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal para Impulsar la Investigación Científico-Técnica y su Transferencia
Subprograma Subprograma Estatal de Generación de Conocimiento
Convocatoria Proyectos de I+D+i (Generación de Conocimiento y Retos Investigación)
Año convocatoria 2021
Plan Estatal 2021-2023 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario UNIVERSITAT POLITECNICA DE CATALUNYA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 13
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Hydrogen-rich gas production by steam reforming and oxidative steam reforming of methanol over La0.6Sr0.4CoO3−δ: Effects of preparation, operation conditions, and redox cycles

  • Morales, Miguel
  • Laguna-Bercero, M. A.
  • Jiménez-Piqué, Emilio
La0.6Sr0.4CoO3−δ (LSC) perovskite, as a potential catalyst precursor for hydrogen (H2)-rich production by steam reforming of methanol (SRM) and oxidative steam reforming of methanol (OSRM), was investigated. For this purpose, LSC was synthesized by the citrate sol–gel method and characterized by complementary analytical techniques. The catalytic activity was studied for the as-prepared and prereduced LSC and compared with the undoped LaCoO3−δ (LCO) at several feed gas compositions. Furthermore, the degradation and regeneration of LSC under repeated redox cycles were studied. The results evidenced that the increase in the water/methanol ratio under SRM, and the O2 addition under OSRM, increased the CO2 formation and decreased both the H2 selectivity and catalyst deactivation caused by carbon deposition. Methanol conversion of the prereduced LSC was significantly enhanced at a lower temperature than that of as-prepared LSC and undoped LCO. This was attributed to the performance of metallic cobalt nanoparticles highly dispersed under reducing atmospheres. The reoxidation program in repetitive redox cycles played a crucial role in the regeneration of catalysts, which could be regenerated to the initial perovskite structure under a specific thermal treatment, minimizing the degradation of the catalytic activity and surface., This research has been supported by Grants PID2021-126614OB-I00 and PID2019-107106RB-C32, funded by MCIN/AEI/10.13039/501100011033 and FEDER. Additional funding has been received from AGAUR, Agency for Administration of University and Research (2021 SGR 01053). M.M. is a Serra Húnter Lecturer Professor, and he is grateful to the Serra Húnter program (Generalitat de Catalunya)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Cobalt-zirconia coated monoliths fabricated by direct ink writing for catalytic applications

  • Razavi, Seyed Ali
  • Fargas, Gemma
  • Serrano, Isabel
  • Laguna-Bercero, M. A.
  • Llanes, Luis
  • Llorca, Jordi
  • Morales, Miguel
Direct Ink Writing (DIW) is a promising technique for fabricating ceramic catalysts with complex geometries and enhanced catalytic performances, but these still require overcoming some challenges to maximize their catalytic and mechanical functionality. In this work, DIW yttria-doped zirconia (YDZ) catalysts were coated with a Co/YDZ catalyst layer. Two configurations based on a dense monolith and a porous one sintered at 1450ºC and 1300ºC were fabricated through DIW, using optimal rheological hydrogel-inks, to investigate the effect of porosity on the mechanical and catalytic performance in the ethanol steam reforming reaction. The monolith sintered at 1450°C achieved the best mechanical and catalytic performance, as it presented the highest Co concentration (2.3 at%) at the catalyst layer. In addition, this monolith exhibited excellent mechanical properties at the interface between contiguous filaments in the multilayer structure. Therefore, this simple approach is a promising method to produce enhanced catalytically and mechanically robust monoliths., The research reported in this paper received support from the EU Regional Development Fund through the Operational FEDER of Catalonia 2014–2020 RIS3CAT-BASE3D, from projects PID2021–126614OB-I00, PID2021–124572OB-C31, PID2022–137274NB-C32, PID2022–137626OB-C31, and CEX2023–001300-M funded by MCIN/AEI/10.13039/501100011033, EU and FEDER. This research was also supported by MCIN with funding from NextGenerationEU (PRTR-C17.I1) within the Planes Complementarios con CCAA (Area of Green Hydrogen and Energy) and it has been carried out in the CSIC Interdisciplinary Thematic Platform (PTI+) Transición Energética Sostenible+ (PTI-TRANSENER+). Additional funding was also received from AGAUR (Agency for Administration of University and Research) under grant number 2021 SGR 01053 and 01061, and from T02–20R (DGA). S.A.R. acknowledges the Ph.D. scholarship received from Universitat Politècnica de Catalunya and Banco Santander (Predoctoral grant 2020 FPU-UPC_068). J.Ll. is Serra Hunter Fellow and is grateful to ICREA Academia program (Generalitat de Catalunya). M.M. is Serra Hunter Fellow. Furthermore, the use of Servicio General de Apoyo a la Investigación (SAI, University of Zaragoza) and the Advanced Microscopy Laboratory (LMA) are also acknowledged. The authors also thank Casimir Casas, Oscar Escuer and Marc Torrente for their assistance during this research., With funding from the Spanish government through the "Unit of Excellence Maria de Maeztu" accreditation (CEX2023-001300-M)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Direct Ink Writing of cobalt-zirconia monoliths for catalytic applications: A novel single-step fabrication approach

  • Razavi, Seyed Ali
  • Fargas, Gemma
  • Vilella, Tània
  • Serrano, Isabel
  • Laguna-Bercero, M. A.
  • Llanes, Luis
  • Rodríguez, Daniel
  • Ginebra, Maria-Pau
  • Llorca, Jordi
  • Morales, Miguel
Additive manufacturing technologies are revolutionizing the fabrication of ceramic catalysts through hierarchical design to enhance catalytic performance and simultaneously improving the efficiency of the manufacturing process by decreasing the initial investment and production steps. This work proposes a fabrication process of cobalt-zirconia monoliths based on Direct-Ink Writing of Co-enriched hydrogel-based ceramic inks, and the debinding and sintering at 600ºC in a single thermal treatment. The effect of Co precursor amount (3.0 −7.0 wt% Co) on the rheological properties of inks and the catalytic performance in ethanol steam reforming is investigated. The results reveal the successful incorporation of Co into rectilinear monoliths with 50 % infill, obtaining strongly Co-rich surfaces. The remarkable catalytic performance of the 5.0 wt% Co monolith at 300–600ºC confirms the feasibility of this novel single-step approach, reaching an appropriate balance between catalytic activity and printability. This outcome may represent a push towards the fabrication of fully 3D-printed monolithic catalysts., The research reported in this paper received support from the EU Regional Development Fund through the Operational FEDER of Catalonia 2014–2020 RIS3CAT-BASE3D, from projects PID2021–124572OB-C31, PID2021–125150OB-I00, PID2021–126614OB-I00, PID2022–137274NB-C32, and PID2022–137626OB-C31 funded by MCIN/AEI/10.13039/501100011033, EU and FEDER. This work was part of Maria de Maeztu Units of Excellence Programme CEX2023–001300-M funded by MCIN/AEI/10.13039/501100011033. This research was also supported by MCIN with funding from NextGenerationEU (PRTR-C17.I1) within the Planes Complementarios con CCAA (Area of Green Hydrogen and Energy) and it has been carried out in the CSIC Interdisciplinary Thematic Platform (PTI+) Transición Energética Sostenible+ (PTI-TRANSENER+). Additional funding was also received from AGAUR (Agency for Administration of University and Research) under grant numbers 2021 SGR 01053 and 01061, and 2017 SGR 1165, and from T02–20R (DGA). S.A.R. acknowledges the Ph.D. scholarship received from Universitat Politècnica de Catalunya and Banco Santander (Predoctoral grant 2020 FPU-UPC_068). T.V. acknowledges the Ph.D. scholarship received from the Barcelona Research Center in Multiscale Science and Engineering of the UPC. M.M and J.Ll. are Serra Hunter Fellows and J.Ll. and M.P.G. are grateful to ICREA Academia Program (Generalitat de Catalunya). Furthermore, the use of Servicio General de Apoyo a la Investigación (SAI, University of Zaragoza) and the Advanced Microscopy Laboratory (LMA) are also acknowledged., With funding from the Spanish government through the "Unit of Excellence Maria de Maeztu" accreditation (CEX2023-001300-M)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

3D-printed Ni/γ-Al2O3 catalysts for CO2 methanation: Effect of Ni loading and sintering temperature

  • Razavi, Seyed Ali
  • Fargas, Gemma
  • Serrano, Isabel
  • Laguna-Bercero, M. A.
  • Vilella, Tània
  • Llanes, Luis
  • Rodríguez, Daniel
  • Ginebra, Maria-Pau
  • Llorca, Jordi
  • Morales, Miguel
Data will be made available on request., Additive manufacturing (AM) technologies are revolutionizing the production of ceramic components, particularly in fields like catalysis, where complex shapes offer remarkable advantages in performance. AM also minimizes material waste while reducing the number of fabrication steps. This work is focused on the fabrication of Ni/γ-Al2O3 monoliths for CO2 methanation in one step by using Direct-Ink Writing (DIW) of Ni-enriched hydrogel-based γ-Al2O3 inks, and the debinding and sintering in a single thermal treatment. For this purpose, the influence of Ni precursor amount (2.5–5.0 wt% Ni) on the rheological properties of inks and the catalytic activity is investigated. Monoliths with woodpile architecture and 50 % infill are sintered at 450 °C and 600 °C to determine the effect of the sintering temperature on the Ni distribution in the catalyst. Results evidence successful incorporation of the metallic active phase into the monolithic structures. Both the Ni amount and sintering temperature are key factors to enhance the CO2 methanation performance. The 5.0 wt% Ni monolith sintered at 450 °C presents both the highest CO2 conversion and methane selectivity at 350–500 °C, due to better reduction degree, dispersion, and smaller size of Ni nanoparticles at the maximum metal loading. These remarkable results demonstrate the potential of DIW for the fabrication of fully 3D-printed monolithic catalysts with well-dispersed metal particles, all while minimizing production steps., The research reported in this paper received support from the EU Regional Development Fund through the Operational FEDER of Catalonia 2014–2020 RIS3CAT-BASE3D, from projects PID2024-156765OB-C21, PID2021-125150OB-I00, PID2021-126614OB-I00, PID2022-137274NB-C32, and PID2022-137626OB-C31 funded by MCIN/AEI/10.13039/501100011033, EU and FEDER. This work was part of Maria de Maeztu Units of Excellence Programme CEX2023-001300-M funded by MCIN/AEI/10.13039/501100011033. This research was also supported by MCIN with funding from NextGenerationEU (PRTR-C17.I1) within the Planes Complementarios con CCAA (Area of Green Hydrogen and Energy) and it has been carried out in the CSIC Interdisciplinary Thematic Platform (PTI+) Transición Energética Sostenible+ (PTI-TRANSENER+). Additional funding was also received from AGAUR (Agency for Administration of University and Research) under grant numbers 2021 SGR 01053 and 01061, and 2017 SGR 1165, and from T02-20R (DGA). S.A.R. acknowledges the Ph.D. scholarship received from Universitat Politècnica de Catalunya and Banco Santander (Predoctoral grant 2020 FPU-UPC_068). T.V. acknowledges the Ph.D. scholarship received from the Barcelona Research Center in Multiscale Science and Engineering of the UPC. J.Ll. and M.M are Serra Hunter Fellows and M.P.G. are grateful to ICREA Academia Program (Generalitat de Catalunya). Furthermore, the use of Servicio General de Apoyo a la Investigación (SAI, University of Zaragoza) and the Advanced Microscopy Laboratory (LMA) are also acknowledged. The authors also thank Gauthier Koch for their assistance during this research., With funding from the Spanish government through the "Unit of Excellence Maria de Maeztu" accreditation (CEX2023-001300-M)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Direct recycling of 3D-printed Co-YDZ catalysts for ethanol steam reforming

  • Razavi, Seyed Ali
  • Fargas, Gemma
  • Serrano, Isabel
  • Laguna-Bercero, M. A.
  • Vilella, Tània
  • Llanes, Luis
  • Rodríguez, Daniel
  • Ginebra, Maria-Pau
  • Llorca, Jordi
  • Morales, Miguel
Data will be made available on request., Additive manufacturing enhances the catalyst performance via hierarchical design. To address environmental and resource concerns, this work aims to fabricate directly recycled 3D-printed monoliths using Direct-Ink Writing (DIW) from 100 % recovered cobalt-zirconia powders. Virgin cobalt-zirconia monoliths were firstly fabricated by DIW of 3.0–7.0 wt% Co-enriched hydrogel-based ceramic inks, followed by calcination at 600°C in a single thermal treatment. After testing the catalytic performance of monoliths in ethanol steam reforming, 3D-printed cobalt-zirconia monoliths were fragmented and subjected to subsequent milling and sieving steps to recover composite cobalt-zirconia powders with the appropriate properties for reuse in DIW. The recovered powders, inks and monoliths were microstructurally, rheologically and catalytically characterized, and then compared to catalysts constituted by virgin materials. The rheology properties of inks for the recycled and virgin monoliths presented an appropriate printability. Furthermore, the catalytic performance of recycled monoliths was close to that exhibited by virgin catalysts. This study demonstrates the feasibility of directly recycling fully 3D-printed catalysts, potentially reducing the environmental impact with a circular production model to enhance sustainability in the catalyst industry., The research reported in this paper received support from the EU Regional Development Fund through the Operational FEDER of Catalonia 2014–2020 RIS3CAT-BASE3D, from projects PID2024–156765OB-C21, PID2021–125150OB-I00, PID2021–126614OB-I00, PID2022–137274NB-C32, and PID2022–137626OB-C31 funded by MCIN/AEI/10.13039/501100011033, EU and FEDER. This work was part of Maria de Maeztu Units of Excellence Programme CEX2023–001300-M funded by MCIN/AEI/10.13039/501100011033. This research was also supported by MCIN with funding from NextGenerationEU (PRTR-C17.I1) within the Planes Complementarios con CCAA (Area of Green Hydrogen and Energy) and it has been carried out in the CSIC Interdisciplinary Thematic Platform (PTI+) Transición Energética Sostenible+ (PTI-TRANSENER+). Additional funding was also received from AGAUR (Agency for Administration of University and Research) under grant numbers 2021 SGR 01053 and 01061, and 2017 SGR 1165, and from T02–20R (DGA). S.A.R. acknowledges the Ph.D. scholarship received from Universitat Politècnica de Catalunya and Banco Santander (Predoctoral grant 2020 FPU-UPC_068). T.V. acknowledges the Ph.D. scholarship received from the Barcelona Research Center in Multiscale Science and Engineering of the UPC. M.M. and J.Ll. are Serra Hunter Fellows and J.Ll. and M.P.G. are grateful to ICREA Academia Program (Generalitat de Catalunya). Furthermore, the use of Servicio General de Apoyo a la Investigación (SAI, University of Zaragoza) and the Advanced Microscopy Laboratory (LMA) are also acknowledged., With funding from the Spanish government through the "Severo Ochoa Centre of Excellence" accreditation (CEX2023-001300-M)., Peer reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

General results for loading and unloading rough elasto-plastic interfaces

  • Pérez Rafols, Francisco|||0000-0002-3556-328X
  • Liang, Xuan-Ming
  • Ciavarella, Michele
From the classical model of Bowden and Tabor it is known that metallic materials make contact only on a small fraction of the nominal contact area, where pressure is so high that plastic deformations is likely. While the contact area has been extensively studied within this context, indentation has attracted less attention. In this work we thus characterize the relationship between load and indentation for nominally flat Gaussian surfaces, finding universal trends which persist when either the level of plasticity or the indentation depth change. We study both loading and unloading trends. Also, we discuss the height distribution of the surfaces resulting from cumulative plastic deformation. For all this cases, we obtain very simple and closed form analytical fittings that allow a convenient and general use of the results here presented. Finally, we compare the results obtained from the model, based on Boundary Element model and perfect plasticity, with experimental result, to justify the validity of its use., FPR received funding support from the Spanish Ministry of Science and Innovation through grant PID2021-407 126614OB-I00 and from the research group RIIS-UPC. XML received funding from the National Natural Science Foundation of China (Grant No. 12302126). MC received no funding., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

On the effect of the height distribution function in adhesion of non Gaussian random rough surfaces, and a simple analytical model (BAM)

  • Pérez Rafols, Francisco|||0000-0002-3556-328X
  • Ciavarella, Michele
Two apparently very different theories of adhesion of rough surfaces called BAM (bearing-area-model), and that of Persson-Tosatti lead to similar predictions concerning the stickiness of Gaussian surfaces: the role of roughness is mainly governed by the low wavevector content of the PSD. Here, we study the adhesion of non-Gaussian surfaces by means of a DMT-based simplified BEM (Boundary-Element-Method), and report a clear difference in the adhesion and stickiness of surfaces with different height distribution function. We then obtain analytical equations for a generalized BAM model. Results of the extended BAM theory compare reasonably well with numerical BEM-DMT predictions. We also notice that any theory based on the surface energy, would show instead insensitivity to height distribution., MC acknowledges support from the Italian Ministry of Education, University and Research (MIUR), Italy under the program “Departments of Excellence” (L.232/2016). FPR acknowledges the support from the Spanish Ministry of Science and Innovation, Spain through the grant PID2021-126614OB-I00., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Towards a universal scaling for the elastic contact between anisotropic and non-gaussian surfaces

  • Pérez Rafols, Francisco|||0000-0002-3556-328X
  • Ciavarella, Michele
Contact between elastic rough surfaces is one of the fundamental problems in tribology. We study with a Boundary Element Method the influence of anisotropy of roughness on the real contact area and on load-separation for both a classical gaussian height distribution and a weibull one, in the common case of power law PSD. We find that anisotropy affects contact area and load-separation similarly for gaussian or non-gaussian surfaces, and therefore the effect can be captured by a single parameter which we extract from Persson’s theory. We further use the results to extend BAM theory of long-range adhesion to gaussian and non-gaussian (weibull) surfaces both isotropic or anisotropic. For the real contact area, results for weibull surfaces are known in the literature., Open access funding provided by Politecnico di Bari within the CRUI-CARE Agreement. FPR acknowledges funding support by the Spanish Ministry of Science and Innovation through grant PID2021-407 126614OB-I00 and by the research group RIIS-UPC. MC acknowledges support from the Italian Ministry of Education, University and Research (MIUR) under the program “Departments of Excellence” (L.232/2016)., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

On the adhesion of sinusoidal surfaces

  • Pérez Rafols, Francisco|||0000-0002-3556-328X
  • Niubó Eslava, Maria|||0000-0002-7395-7159
In this work, we study the adhesive loading and unloading of a one-dimensional sinusoidal surface and use design of experiments to provide for response surface maps for the work of adhesion and the interaction length, which depend only on Johnson’s parameter and the Maugis parameter . As showcased by some example, these can be used to replace the fine scale roughness by a cohesive zone model. Besides that, we provide ranges of and in which the most common analytical solutions present accurate results. Finally, we characterize the presence of instabilities in the loading and unloading profiles., The authors were funded by the Spanish Ministry of Science and Innovation through grant PID2021- 407 126614OB-I00 and through the research group RIIS-UPC., Peer Reviewed
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

On the adhesion of sinusoidal surfaces

  • Pérez Rafols, Francisco
  • Niubó Eslava, Maria
In this work, we study the adhesive loading and unloading of a one-dimensional sinusoidal surface and use design of experiments to provide for response surface maps for the work of adhesion and the interaction length, which depend only on Johnson’s parameter and the Maugis parameter . As showcased by some example, these can be used to replace the fine scale roughness by a cohesive zone model. Besides that, we provide ranges of and in which the most common analytical solutions present accurate results. Finally, we characterize the presence of instabilities in the loading and unloading profiles., The authors were funded by the Spanish Ministry of Science and Innovation through grant PID2021- 407 126614OB-I00 and through the research group RIIS-UPC., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

On the effect of the height distribution function in adhesion of non Gaussian random rough surfaces, and a simple analytical model (BAM)

  • Pérez Rafols, Francisco
  • Ciavarella, Michele
Two apparently very different theories of adhesion of rough surfaces called BAM (bearing-area-model), and that of Persson-Tosatti lead to similar predictions concerning the stickiness of Gaussian surfaces: the role of roughness is mainly governed by the low wavevector content of the PSD. Here, we study the adhesion of non-Gaussian surfaces by means of a DMT-based simplified BEM (Boundary-Element-Method), and report a clear difference in the adhesion and stickiness of surfaces with different height distribution function. We then obtain analytical equations for a generalized BAM model. Results of the extended BAM theory compare reasonably well with numerical BEM-DMT predictions. We also notice that any theory based on the surface energy, would show instead insensitivity to height distribution., MC acknowledges support from the Italian Ministry of Education, University and Research (MIUR), Italy under the program “Departments of Excellence” (L.232/2016). FPR acknowledges the support from the Spanish Ministry of Science and Innovation, Spain through the grant PID2021-126614OB-I00., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

General results for loading and unloading rough elasto-plastic interfaces

  • Pérez Rafols, Francisco
  • Liang, Xuan-Ming
  • Ciavarella, Michele
From the classical model of Bowden and Tabor it is known that metallic materials make contact only on a small fraction of the nominal contact area, where pressure is so high that plastic deformations is likely. While the contact area has been extensively studied within this context, indentation has attracted less attention. In this work we thus characterize the relationship between load and indentation for nominally flat Gaussian surfaces, finding universal trends which persist when either the level of plasticity or the indentation depth change. We study both loading and unloading trends. Also, we discuss the height distribution of the surfaces resulting from cumulative plastic deformation. For all this cases, we obtain very simple and closed form analytical fittings that allow a convenient and general use of the results here presented. Finally, we compare the results obtained from the model, based on Boundary Element model and perfect plasticity, with experimental result, to justify the validity of its use., FPR received funding support from the Spanish Ministry of Science and Innovation through grant PID2021-407 126614OB-I00 and from the research group RIIS-UPC. XML received funding from the National Natural Science Foundation of China (Grant No. 12302126). MC received no funding., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Towards a universal scaling for the elastic contact between anisotropic and non-gaussian surfaces

  • Pérez Rafols, Francisco
  • Ciavarella, Michele
Contact between elastic rough surfaces is one of the fundamental problems in tribology. We study with a Boundary Element Method the influence of anisotropy of roughness on the real contact area and on load-separation for both a classical gaussian height distribution and a weibull one, in the common case of power law PSD. We find that anisotropy affects contact area and load-separation similarly for gaussian or non-gaussian surfaces, and therefore the effect can be captured by a single parameter which we extract from Persson’s theory. We further use the results to extend BAM theory of long-range adhesion to gaussian and non-gaussian (weibull) surfaces both isotropic or anisotropic. For the real contact area, results for weibull surfaces are known in the literature., Open access funding provided by Politecnico di Bari within the CRUI-CARE Agreement. FPR acknowledges funding support by the Spanish Ministry of Science and Innovation through grant PID2021-407 126614OB-I00 and by the research group RIIS-UPC. MC acknowledges support from the Italian Ministry of Education, University and Research (MIUR) under the program “Departments of Excellence” (L.232/2016)., Peer Reviewed, Postprint (published version)