Pasar al contenido principal

LASER ASSISTED SINTERING OF ELECTROLYSERS (LASE)

PID2022-137626OB-C31

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal para Impulsar la Investigación Científico-Técnica y su Transferencia
Subprograma Subprograma Estatal de Generación de Conocimiento
Convocatoria Proyectos de I+D+i (Generación de Conocimiento y Retos Investigación)
Año convocatoria 2022
Plan Estatal 2021-2023 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario AGENCIA ESTATAL CONSEJO SUPERIOR DE INVESTIGACIONES CIENTIFICAS (CSIC)

Resultados relacionados

Resultados totales (Incluyendo duplicados): 11
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Cobalt-zirconia coated monoliths fabricated by direct ink writing for catalytic applications

  • Razavi, Seyed Ali
  • Fargas, Gemma
  • Serrano, Isabel
  • Laguna-Bercero, M. A.
  • Llanes, Luis
  • Llorca, Jordi
  • Morales, Miguel
Direct Ink Writing (DIW) is a promising technique for fabricating ceramic catalysts with complex geometries and enhanced catalytic performances, but these still require overcoming some challenges to maximize their catalytic and mechanical functionality. In this work, DIW yttria-doped zirconia (YDZ) catalysts were coated with a Co/YDZ catalyst layer. Two configurations based on a dense monolith and a porous one sintered at 1450ºC and 1300ºC were fabricated through DIW, using optimal rheological hydrogel-inks, to investigate the effect of porosity on the mechanical and catalytic performance in the ethanol steam reforming reaction. The monolith sintered at 1450°C achieved the best mechanical and catalytic performance, as it presented the highest Co concentration (2.3 at%) at the catalyst layer. In addition, this monolith exhibited excellent mechanical properties at the interface between contiguous filaments in the multilayer structure. Therefore, this simple approach is a promising method to produce enhanced catalytically and mechanically robust monoliths., The research reported in this paper received support from the EU Regional Development Fund through the Operational FEDER of Catalonia 2014–2020 RIS3CAT-BASE3D, from projects PID2021–126614OB-I00, PID2021–124572OB-C31, PID2022–137274NB-C32, PID2022–137626OB-C31, and CEX2023–001300-M funded by MCIN/AEI/10.13039/501100011033, EU and FEDER. This research was also supported by MCIN with funding from NextGenerationEU (PRTR-C17.I1) within the Planes Complementarios con CCAA (Area of Green Hydrogen and Energy) and it has been carried out in the CSIC Interdisciplinary Thematic Platform (PTI+) Transición Energética Sostenible+ (PTI-TRANSENER+). Additional funding was also received from AGAUR (Agency for Administration of University and Research) under grant number 2021 SGR 01053 and 01061, and from T02–20R (DGA). S.A.R. acknowledges the Ph.D. scholarship received from Universitat Politècnica de Catalunya and Banco Santander (Predoctoral grant 2020 FPU-UPC_068). J.Ll. is Serra Hunter Fellow and is grateful to ICREA Academia program (Generalitat de Catalunya). M.M. is Serra Hunter Fellow. Furthermore, the use of Servicio General de Apoyo a la Investigación (SAI, University of Zaragoza) and the Advanced Microscopy Laboratory (LMA) are also acknowledged. The authors also thank Casimir Casas, Oscar Escuer and Marc Torrente for their assistance during this research., With funding from the Spanish government through the "Unit of Excellence Maria de Maeztu" accreditation (CEX2023-001300-M)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Direct Ink Writing of cobalt-zirconia monoliths for catalytic applications: A novel single-step fabrication approach

  • Razavi, Seyed Ali
  • Fargas, Gemma
  • Vilella, Tània
  • Serrano, Isabel
  • Laguna-Bercero, M. A.
  • Llanes, Luis
  • Rodríguez, Daniel
  • Ginebra, Maria-Pau
  • Llorca, Jordi
  • Morales, Miguel
Additive manufacturing technologies are revolutionizing the fabrication of ceramic catalysts through hierarchical design to enhance catalytic performance and simultaneously improving the efficiency of the manufacturing process by decreasing the initial investment and production steps. This work proposes a fabrication process of cobalt-zirconia monoliths based on Direct-Ink Writing of Co-enriched hydrogel-based ceramic inks, and the debinding and sintering at 600ºC in a single thermal treatment. The effect of Co precursor amount (3.0 −7.0 wt% Co) on the rheological properties of inks and the catalytic performance in ethanol steam reforming is investigated. The results reveal the successful incorporation of Co into rectilinear monoliths with 50 % infill, obtaining strongly Co-rich surfaces. The remarkable catalytic performance of the 5.0 wt% Co monolith at 300–600ºC confirms the feasibility of this novel single-step approach, reaching an appropriate balance between catalytic activity and printability. This outcome may represent a push towards the fabrication of fully 3D-printed monolithic catalysts., The research reported in this paper received support from the EU Regional Development Fund through the Operational FEDER of Catalonia 2014–2020 RIS3CAT-BASE3D, from projects PID2021–124572OB-C31, PID2021–125150OB-I00, PID2021–126614OB-I00, PID2022–137274NB-C32, and PID2022–137626OB-C31 funded by MCIN/AEI/10.13039/501100011033, EU and FEDER. This work was part of Maria de Maeztu Units of Excellence Programme CEX2023–001300-M funded by MCIN/AEI/10.13039/501100011033. This research was also supported by MCIN with funding from NextGenerationEU (PRTR-C17.I1) within the Planes Complementarios con CCAA (Area of Green Hydrogen and Energy) and it has been carried out in the CSIC Interdisciplinary Thematic Platform (PTI+) Transición Energética Sostenible+ (PTI-TRANSENER+). Additional funding was also received from AGAUR (Agency for Administration of University and Research) under grant numbers 2021 SGR 01053 and 01061, and 2017 SGR 1165, and from T02–20R (DGA). S.A.R. acknowledges the Ph.D. scholarship received from Universitat Politècnica de Catalunya and Banco Santander (Predoctoral grant 2020 FPU-UPC_068). T.V. acknowledges the Ph.D. scholarship received from the Barcelona Research Center in Multiscale Science and Engineering of the UPC. M.M and J.Ll. are Serra Hunter Fellows and J.Ll. and M.P.G. are grateful to ICREA Academia Program (Generalitat de Catalunya). Furthermore, the use of Servicio General de Apoyo a la Investigación (SAI, University of Zaragoza) and the Advanced Microscopy Laboratory (LMA) are also acknowledged., With funding from the Spanish government through the "Unit of Excellence Maria de Maeztu" accreditation (CEX2023-001300-M)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

High performance La2NiO4+δ oxygen and Ni–Ce0.9Gd0.1O2−δ fuel electrodes for thin film reversible solid oxide cells

  • Riaz, Adeel
  • Sirvent, Juande
  • Zueco-Vincelle, Juan
  • Buzi, Fjorelo
  • Panisset, Silvère
  • Stangl, Alexander
  • Rapenne, Laetitia
  • Baiutti, Federico
  • Mermoux, Michel
  • Laguna-Bercero, M. A.
  • Tarancón, Albert
  • Burriel, Mónica
Thin film reversible solid oxide cells (TF-rSOCs) are attracting a great deal of interest as they promise to operate at much lower temperatures (400–600 °C) than state-of-the-art commercial fuel electrode-supported cells (600–800 °C). However, in all-ceramics TF-rSOCs the high polarization resistance of the electrodes limits the cell performance. To overcome this limitation, high performing oxygen and fuel electrodes were selected and their nanostructure was optimized. Thin nanoporous films of La2NiO4+δ were deposited as oxygen electrode by Pulsed Injection Metal Organic Chemical Vapor Deposition (PI-MOCVD) with different thickness. As for the fuel electrode, thin films of Ni–Ce0.9Gd0.1O2−δ (NiCGO) were deposited by Pulsed Laser Deposition (PLD) at various temperatures and pO2. The electrochemical activity of the oxygen and fuel electrodes was measured by Electrical Conductivity Relaxation (ECR) and Electrochemical Impedance Spectroscopy (EIS), respectively. The optimized electrodes were then deposited on a YSZ single crystal electrolyte and the cell was measured in fuel cell and electrolysis modes showing high performance with a power density of 70 mW cm−2 at 0.7 V and a current density of −44 mA cm−2 at 1.3 V at a low operating temperature of 600 °C. These results demonstrate the potential of using these materials as electrodes in TF-rSOCs., This project has received funding from the European Union's Horizon 2020 Research and Innovation Program under grant agreements no. 824072 (Harvestore project) and no. 101017709 (EPISTORE project) and by the Centre of Excellence of Multifunctional Architectured Materials ‘CEMAM’ no. ANR-10-LABX-44-01 as part of the ‘Investments for the Future’ Program. This research has benefited from characterization equipment of the Grenoble INP – CMTC platform. The authors also acknowledge support from the Generalitat de Catalunya (2021-SGR-00750, NANOEN). This research has also received funding from PID2022-137626OB-C31 (MCIU/AEI/FEDER, UE), NextGenerationEU (PRTR-C17.I1) and T02_23R (DGA) grants., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Multifunctional polyoxomolybdate ionic liquid coatings for mitigating microbiologically influenced corrosion

  • Malefioudaki, Mariella
  • Misra, Archismita
  • Sbeity, Nadja
  • Zueco-Vincelle, Juan
  • Laguna-Bercero, M. A.
  • Koerdt, Andrea
  • Martín-Rapún, Rafael
  • Mitchell, Scott G.
Corrosion of metals and other materials in marine environments poses significant economic, operational, safety, and environmental challenges across the oil and gas industry, the renewable energy sector, and maritime infrastructure. Microbiologically influenced corrosion (MIC) accounts for a substantial portion of this corrosion, with sulfate-reducing bacteria (SRB) and methanogenic archaea (MA) being key contributors. Conventional methods such as cathodic polarization have proven insufficient in mitigating the colonization of corrosive microbial communities in real marine environments, requiring the development of alternative, broad-spectrum antimicrobial strategies to prevent such biofilm formation. Recently, molybdate has emerged as a potential alternative to traditional biocides and nitrate. Our hypothesis is polyoxometalate-ionic liquids (POM-ILs), which exhibit antimicrobial and anticorrosion properties, could have a broader spectrum of antimicrobial activity than demonstrated until now and could be capable of shielding and protecting sensitive metal surfaces from the extreme acidic environments produced by MIC microorganisms. Here we show how two prototype polyoxomolybdate-based POM-ILs, [(CH3(CH2)6)4N]2[Mo6O19] and [(CH3(CH2)6)4N]4[Mo8O26], demonstrated antimicrobial activity at microgram per millilitre concentrations, prevented biofilm formation on metal surfaces, and provided resistance to corrosive acidic environments. Furthermore, impedance measurements were commensurate with electron microscopy studies showing that POM-IL-coated brass coupons withstood extremely corrosive environments. These proof-of-concept results demonstrate how multi-functional POM-IL coatings represent promising MIC mitigation solutions by providing a hydrophobic acid-resistant and biocidal protective layer that prevents biocolonisation and acidic corrosion by MIC microorganisms., This work was funded through the grants PID2022-141276OB-I00, PID2022-137626OB-C31 and CEX2023-001286-S funded by MCIN/AEI/10.13039/501100011033 (Ministerio de Ciencia e Innovación/Agencia Estatal de Investigación, Spain). This study was supported by MCIN with funding from the European Union NextGenerationEU (PRTR-C17.I1) promoted by the Government of Aragón. The authors also acknowledge Fondo Social del Gobierno de Aragón (grupo DGA E15_23R and T02_23R). The authors acknowledge the Servicio General de Apoyo a la Investigación-SAI (Universidad de Zaragoza), for the use of instrumentation as well as the technical advice provided by the National Facility ELECMI ICTS, node “Laboratorio de Microscopías Avanzadas” at the University of Zaragoza. This work was supported by COST (European Cooperation in Science and Technology) and based upon work from COST Action European MIC Network—New paths for science, sustainability and standards (Euro-MIC) [CA20130]., With funding from the Spanish government through the "Severo Ochoa Centre of Excellence" accreditation (CEX2023-001286-S)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Synthesis of MCM-41 and SBA-15 from rice husk silica and their carbon replicas for hydrogen adsorption

  • Juárez-Pérez, Emilio J.
  • Téllez, Jhoan F.
  • Laguna-Bercero, M. A.
  • Moyano, E. Laura
  • Gómez Costa, Marcos B.
Data are available upon reasonable request from the corresponding author., [Background] Rice husk, an abundant agricultural by-product, presents a promising renewable silicon source for producing carbon-based materials through sustainable and eco-friendly approaches. Among emerging clean energy solutions, hydrogen storage remains a critical challenge for the practical deployment of hydrogen energy systems. This study explores the use of rice husk-derived silica to synthesize mesoporous nanostructured silicon materials and their corresponding carbon replicas. The goal is to develop efficient materials for hydrogen adsorption, with performance surpassing that of other biomass-derived carbons synthesized under comparable conditions – thereby offering a competitive and sustainable solution for hydrogen storage., [Results] A cost-effective, sustainable synthesis route was developed to produce siliceous templates MCM-41 and SBA-15 using cetyltrimethylammonium bromide and Pluronic P123 as surfactants. Their carbon replicas – rice husk ash (RHA)-MCM-41 and RHA-SBA-15 – were fabricated via a nanocasting method employing sucrose as a carbon source. The resulting materials were characterized using X-ray diffraction, scanning electron microscopy, transmission electron microscopy, and nitrogen adsorption–desorption techniques. Notably, the synthesized mesoporous carbons, RHA-CMK-3 and RHA-RMCM-41, exhibited high surface areas ranging from 800 to 1400 m2g−1 and featured both mesoporous and microporous structures., [Conclusion] The synthesized carbon replicas demonstrated significant hydrogen adsorption capabilities. Among them, RHA-CMK-3 showed the highest hydrogen storage performance, reaching 3.6 wt% at 196.15 °C and 10 bar. These findings highlight the potential of rice husk-derived nanostructured carbons as efficient and sustainable materials for hydrogen storage applications. Moreover, the obtained materials exhibit hydrogen adsorption capacities surpassing those of other biomass-derived carbons synthesized under similar conditions, reinforcing their competitive advantage for energy storage solutions., The authors acknowledge the financial support provided by CONICET Argentina, PIP CONICET 11220200100771CO and PIBAA 2872021010 0134CO and SECyT-UNC (Consolidar 2023). The authors thank the National Institute of Agricultural Technology (INTA-Entre Rios), Argentina for the facility of rice husk. JFT thanks CONICET for a fellowship. This research has also received funding from PID2022-137626OB-C31 (MCIU/AEI/FEDER, UE) and COOPA20437 (CSIC) grants., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Praseodymium and gadolinium doped ceria as oxygen electrode for solid oxide cell applications

  • Morales-Zapata, Miguel A.
  • Larrea, Ángel
  • Laguna-Bercero, M. A.
[EN] This study analyzes the structural and electrochemical properties of praseodymium- and gadolinium-doped ceria (CPGO) samples formed by the sintering reaction of Pr2NiO4+δ (PNO) and Ce0.9Gd0.1O2−δ (GDC). X-ray powder diffraction analysis confirmed a single-phase cubic CPGO structure as a primary phase. The cationic compositions were determined using energy dispersive spectroscopy (EDS) in a scanning transmission electron microscope (STEM), while core-loss electron energy-loss spectroscopy (EELS) was used to determine the valence of Ce and Pr. The compatibility between thermal expansion coefficients validated their integration with electrolytes at the typical Solid Oxide Cell (SOC) operation temperatures. Oxygen chemical diffusion and surface exchange coefficients were investigated using the electrical conductivity relaxation (ECR) method at intervals of partial oxygen pressures between 0.10 and 0.21 atm and 600 °C and 800 °C. Finally, the samples were tested in symmetrical cells by electrochemical impedance spectroscopy (EIS) between 700 °C and 850 °C. A polarization resistance of 0.17 Ω cm2 at 850 °C was obtained for CPGO air electrodes formed by sintering a mixture of 80% by weight of GDC and 20% by weight of PNO. These findings confirm that PNO–GDC mixtures forming CPGO oxides are excellent candidates for SOC applications., [ES] En este estudio se analizan las propiedades estructurales y electroquímicas de composites formados por la reacción de sinterización de Pr2NiO4+δ (PNO) y Ce0.9Gd0.1O2-δ (GDC). Los refinamientos de Rietveld de los patrones de difracción de rayos X confirmaron una estructura cúbica monofásica de ceria dopada con praseodimio y gadolinio (CPGO) como fase primaria. Las composiciones catiónicas de CPGO se determinaron mediante espectroscopia de dispersión de energía (EDS) en un microscopio electrónico de transmisión de barrido (STEM), mientras que se utilizó espectroscopia de pérdida de energía de electrones (EELS) para determinar la valencia de Ce y Pr. La compatibilidad entre coeficientes de expansión térmica validó la integración de los electrodos con electrolitos a las temperaturas de operación típicas de las pilas de óxido sólido (SOC). Los coeficientes de difusión química de oxígeno y de intercambio superficial se determinaron mediante relajación de la conductividad eléctrica (ECR). Finalmente, se caracterizaron celdas simétricas mediante espectroscopia de impedancia electroquímica (EIS), obteniendo una baja resistencia de polarización de 0.17 Ω cm2 a 850 °C para electrodos de aire compuestos por 80% de GDC y 20% de PNO en peso. Estos hallazgos confirman que los electrodos de CPGO son excelentes candidatos para aplicaciones SOC., This research has received funding from grants PID2022-137626OB-C31, funded by MCIN/AEI/10.13039/501100011033 FEDER, UE and grant DGA T02-23R, funded by Gobierno de Aragón. Furthermore, the use of Servicio General de Apoyo a la Investigación (SAI, University of Zaragoza) and the Advanced Microscopy Laboratory (LMA) are also acknowledged. This research was also supported by MCIN with funding from NextGenerationEU (PRTR-C17.I1) within the Planes Complementarios con CCAA (Area of Green Hydrogen and Energy) and it has been carried out in the CSIC Interdisciplinary Thematic Platform (PTI+) Transición Energética Sostenible + (PTI− TRANSENER+)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

3D-printed Ni/γ-Al2O3 catalysts for CO2 methanation: Effect of Ni loading and sintering temperature

  • Razavi, Seyed Ali
  • Fargas, Gemma
  • Serrano, Isabel
  • Laguna-Bercero, M. A.
  • Vilella, Tània
  • Llanes, Luis
  • Rodríguez, Daniel
  • Ginebra, Maria-Pau
  • Llorca, Jordi
  • Morales, Miguel
Data will be made available on request., Additive manufacturing (AM) technologies are revolutionizing the production of ceramic components, particularly in fields like catalysis, where complex shapes offer remarkable advantages in performance. AM also minimizes material waste while reducing the number of fabrication steps. This work is focused on the fabrication of Ni/γ-Al2O3 monoliths for CO2 methanation in one step by using Direct-Ink Writing (DIW) of Ni-enriched hydrogel-based γ-Al2O3 inks, and the debinding and sintering in a single thermal treatment. For this purpose, the influence of Ni precursor amount (2.5–5.0 wt% Ni) on the rheological properties of inks and the catalytic activity is investigated. Monoliths with woodpile architecture and 50 % infill are sintered at 450 °C and 600 °C to determine the effect of the sintering temperature on the Ni distribution in the catalyst. Results evidence successful incorporation of the metallic active phase into the monolithic structures. Both the Ni amount and sintering temperature are key factors to enhance the CO2 methanation performance. The 5.0 wt% Ni monolith sintered at 450 °C presents both the highest CO2 conversion and methane selectivity at 350–500 °C, due to better reduction degree, dispersion, and smaller size of Ni nanoparticles at the maximum metal loading. These remarkable results demonstrate the potential of DIW for the fabrication of fully 3D-printed monolithic catalysts with well-dispersed metal particles, all while minimizing production steps., The research reported in this paper received support from the EU Regional Development Fund through the Operational FEDER of Catalonia 2014–2020 RIS3CAT-BASE3D, from projects PID2024-156765OB-C21, PID2021-125150OB-I00, PID2021-126614OB-I00, PID2022-137274NB-C32, and PID2022-137626OB-C31 funded by MCIN/AEI/10.13039/501100011033, EU and FEDER. This work was part of Maria de Maeztu Units of Excellence Programme CEX2023-001300-M funded by MCIN/AEI/10.13039/501100011033. This research was also supported by MCIN with funding from NextGenerationEU (PRTR-C17.I1) within the Planes Complementarios con CCAA (Area of Green Hydrogen and Energy) and it has been carried out in the CSIC Interdisciplinary Thematic Platform (PTI+) Transición Energética Sostenible+ (PTI-TRANSENER+). Additional funding was also received from AGAUR (Agency for Administration of University and Research) under grant numbers 2021 SGR 01053 and 01061, and 2017 SGR 1165, and from T02-20R (DGA). S.A.R. acknowledges the Ph.D. scholarship received from Universitat Politècnica de Catalunya and Banco Santander (Predoctoral grant 2020 FPU-UPC_068). T.V. acknowledges the Ph.D. scholarship received from the Barcelona Research Center in Multiscale Science and Engineering of the UPC. J.Ll. and M.M are Serra Hunter Fellows and M.P.G. are grateful to ICREA Academia Program (Generalitat de Catalunya). Furthermore, the use of Servicio General de Apoyo a la Investigación (SAI, University of Zaragoza) and the Advanced Microscopy Laboratory (LMA) are also acknowledged. The authors also thank Gauthier Koch for their assistance during this research., With funding from the Spanish government through the "Unit of Excellence Maria de Maeztu" accreditation (CEX2023-001300-M)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Direct recycling of 3D-printed Co-YDZ catalysts for ethanol steam reforming

  • Razavi, Seyed Ali
  • Fargas, Gemma
  • Serrano, Isabel
  • Laguna-Bercero, M. A.
  • Vilella, Tània
  • Llanes, Luis
  • Rodríguez, Daniel
  • Ginebra, Maria-Pau
  • Llorca, Jordi
  • Morales, Miguel
Data will be made available on request., Additive manufacturing enhances the catalyst performance via hierarchical design. To address environmental and resource concerns, this work aims to fabricate directly recycled 3D-printed monoliths using Direct-Ink Writing (DIW) from 100 % recovered cobalt-zirconia powders. Virgin cobalt-zirconia monoliths were firstly fabricated by DIW of 3.0–7.0 wt% Co-enriched hydrogel-based ceramic inks, followed by calcination at 600°C in a single thermal treatment. After testing the catalytic performance of monoliths in ethanol steam reforming, 3D-printed cobalt-zirconia monoliths were fragmented and subjected to subsequent milling and sieving steps to recover composite cobalt-zirconia powders with the appropriate properties for reuse in DIW. The recovered powders, inks and monoliths were microstructurally, rheologically and catalytically characterized, and then compared to catalysts constituted by virgin materials. The rheology properties of inks for the recycled and virgin monoliths presented an appropriate printability. Furthermore, the catalytic performance of recycled monoliths was close to that exhibited by virgin catalysts. This study demonstrates the feasibility of directly recycling fully 3D-printed catalysts, potentially reducing the environmental impact with a circular production model to enhance sustainability in the catalyst industry., The research reported in this paper received support from the EU Regional Development Fund through the Operational FEDER of Catalonia 2014–2020 RIS3CAT-BASE3D, from projects PID2024–156765OB-C21, PID2021–125150OB-I00, PID2021–126614OB-I00, PID2022–137274NB-C32, and PID2022–137626OB-C31 funded by MCIN/AEI/10.13039/501100011033, EU and FEDER. This work was part of Maria de Maeztu Units of Excellence Programme CEX2023–001300-M funded by MCIN/AEI/10.13039/501100011033. This research was also supported by MCIN with funding from NextGenerationEU (PRTR-C17.I1) within the Planes Complementarios con CCAA (Area of Green Hydrogen and Energy) and it has been carried out in the CSIC Interdisciplinary Thematic Platform (PTI+) Transición Energética Sostenible+ (PTI-TRANSENER+). Additional funding was also received from AGAUR (Agency for Administration of University and Research) under grant numbers 2021 SGR 01053 and 01061, and 2017 SGR 1165, and from T02–20R (DGA). S.A.R. acknowledges the Ph.D. scholarship received from Universitat Politècnica de Catalunya and Banco Santander (Predoctoral grant 2020 FPU-UPC_068). T.V. acknowledges the Ph.D. scholarship received from the Barcelona Research Center in Multiscale Science and Engineering of the UPC. M.M. and J.Ll. are Serra Hunter Fellows and J.Ll. and M.P.G. are grateful to ICREA Academia Program (Generalitat de Catalunya). Furthermore, the use of Servicio General de Apoyo a la Investigación (SAI, University of Zaragoza) and the Advanced Microscopy Laboratory (LMA) are also acknowledged., With funding from the Spanish government through the "Severo Ochoa Centre of Excellence" accreditation (CEX2023-001300-M)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

State of the art, challenges and perspective on laser machined corrugated interfaces for solid oxide cells and devices

  • Laguna-Bercero, M. A.
  • Iwai, Hiroshi
  • Kishimoto, Masashi
  • Larrea, Ángel
Solid oxide cells (SOCs) are among the most efficient energy conversion technologies available. A recent strategy to enhance their performance involves engineering the structure of SOC components from the microscale to the mesoscale. One promising method to achieve this is through advanced laser ceramic processing techniques. These approaches are also highly relevant to other energy technologies, such as solid-state batteries and membranes, that aim to improve energy generation and conversion efficiency. By applying laser machining, it is possible to precisely control the mesoscale structure of SOC components, particularly by tailoring the interfaces between electrodes and the electrolyte. This structural optimization can significantly reduce the activation component of the resistance of the cell approximately in the same proportion to the increase in the electrochemically active volume. Simultaneously, enlarging the electrolyte surface area leads to a reduction in ohmic resistance, roughly proportional to the increase in the interfacial area. This represents a novel SOC design concept that, in theory, could improve device performance by a factor of four. It also offers potential benefits such as increased durability and lower operating temperatures. In this perspective, we summarize the key theoretical and experimental advances made in this area and outline future directions for research and development., This research has received funding from PID2022-137626OB-C31 (MCIU/AEI/FEDER, UE), NextGenerationEU (PRTR-C17.I1) and T02_23R (DGA) Grants., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Template-assisted synthesis of LaCoO3 from bio-silica: Catalytic insights into rice husk pyrolysis

  • Téllez, Jhoan F.
  • Juárez-Pérez, Emilio J.
  • Brunetti, Verónica
  • Laguna-Bercero, M. A.
  • Fuertes, Valeria C.
  • De Paoli, Juan M.
  • Moyano, E. Laura
Data availability: Processed data supporting the figures and tables will be made available by the corresponding author upon reasonable request., This study presents the synthesis of LaCoO₃ perovskites via a nanocasting approach using bio-silica extracted from residual rice husk (RH). The bio-silica was employed to prepare MCM-41 and SBA-15 hard templates, which served as scaffolds for perovskite formation. The resulting materials were thoroughly characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD), and nitrogen physisorption. The MCM-41 and SBA-15 templates exhibited high surface areas (1011 and 867 m² g⁻¹, respectively), comparable to commercial silica. After template removal, the LaCoO₃ perovskites retained significant surface areas of 55 m² g⁻¹ (MCM-41) and 80 m² g⁻¹ (SBA-15), with their texture and structure strongly influenced by the template type. The catalytic performance of nanocast LaCoO₃ perovskites and a sol–gel reference sample was evaluated in the fast pyrolysis of rice husk at 400 °C using 5 and 20 wt% catalyst loadings. Catalysts slightly increased the overall bio-oil yield (34–45 %), particularly at higher loading. Remarkably, while non-catalytic and 5 wt% catalytic pyrolysis produced bio-oils containing over 50 compounds, increasing the catalyst loading to 20 wt% reduced this number to 17–26 compounds, depending on the catalyst employed. The bio-oils were mainly composed of anhydrosugars; oxygenates (mainly furans and carbonyl-containing compounds); and aromatics, primarily phenolic derivatives. At higher loading, perovskite catalysts promoted selective pathways, enriching the pyrolysates in valuable products such as levoglucosan and 2,3-dihydrobenzofuran. These findings demonstrate the potential of LaCoO₃-based catalysts to modulate product selectivity in the fast pyrolysis of lignocellulosic biomass, offering promising opportunities for the valorization of agro-industrial residues., This work was supported by the National Research Council of Argentina (Proyecto de Unidad Ejecutora-PUE 2017-CONICET #22920170100092), and Secretary of Science and Technology from National University of Córdoba (Proyecto SECyT-UNC Consolidar 2018–2021 PIP Nro. 33620180100687CB). J.F.T. thanks CONICET for the fellowship, as well as CSIC for granting the i-COOP+ 2020 Project (COOPA 20437). This research has also received funding from grants PID2022–137626OB-C31, funded by MCIN/AEI/10.13039/501100011033 FEDER, UE and grant DGA T02–23R, funded by Gobierno de Aragón. Furthermore, the use of Servicio General de Apoyo a la Investigación (SAI, University of Zaragoza) and the Advanced Microscopy Laboratory (LMA) are also acknowledged. Likewise, the authors are grateful for the collaboration of the PROCACEF-INMA group. Authors thank the National Institute of Agricultural Technology (INTA), Entre Ríos, Argentina, for the facility of rice husk. Laboratorio de Análisis de Materiales por Espectrometría de Rayos X (LAMARX, CONICET-UNC, Córdoba) and Laboratorio de Rayos X (INFIQC-CONICET, FCQ-UNC, Córdoba) is gratefully acknowledged for the use of FESEM and XRD, respectively., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Structural analysis of Pb-based organic–inorganic metal halide perovskites modified with Cetyltrimethylammonium bromide and 2-Aminopyrazine: Effects on stability and band gap

  • Tabares, Laurenth G.
  • Salamanca-Perdigón, Kevin
  • Lozano, Johan D.
  • Téllez, Jhoan F.
  • Laguna-Bercero, M. A.
  • Macías, Mario A.
The synthesis of the hybrid organic–inorganic metal halide perovskites (C19H42N)3Pb2Cl7, (C19H42N)3Pb2Br7, (C4H7N3)2Cl2PbCl4, and (C4H7N3)2Br2PbBr4 is reported. These Pb-based structures were obtained using cetyltrimethylammonium bromide (CTAB) and 2-aminopyrazine (2-APZ) as organic precursors, respectively. Single-crystal X-ray diffraction analysis revealed that the asymmetric unit for CTAB-based compounds contains three [(C16H33)N(CH3)3]+ cations and a dinuclear [Pb2Cl7]3− unit composed of two lead-centered coordination polyhedra. In contrast, the 2-APZ-based compounds show [PbCl6]4− octahedra connected through vertex sharing to form layered structures alternating with organic [C4H7N3]2+ cations. In both cases, substitution of Cl by Br produced isostructural compounds, but changed the band gap values: from 3.6 eV to 3.3 eV for CTAB-based perovskites and from 2.5 eV to 2.1 eV for 2-APZ-based perovskites. Despite their lower band gap, the 2-APZ-derived compounds exhibited poor ambient stability. Conversely, CTAB-based compounds, although having a higher band gap, demonstrated enhanced thermal and environmental stability due to their hydrophobic nature. The different molecular sizes between 2-APZ and CTAB created different space between inorganic sheets leading to different quantum confinement. These findings highlight the potential for designing improved materials with both low band gap and high stability through mixed occupancy of different organic molecules., Authors wish to credit Universidad de los Andes, Colombia, for the financial support. Particularly, L.G.T. and M.A.M. acknowledge support from Departamento de Química and Facultad de Ciencias at the Universidad de los Andes, Colombia (project numbers INV-2026-229-3627 and INV-2023-176-2938). M.A.L.B. and J. T. acknowledge funding from PID2022-137626OB-C31, funded by MCIN/AEI/10.13039/501100011033FEDER, UE as well from the Gobierno de Aragón (DGA) under Project T02-23R. HR-TEM experiments have been conducted in the Laboratorio de Microscopias Avanzadas (LMA) at Universidad de Zaragoza., Peer reviewed