Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 7
Encontrada(s) 1 página(s)

Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Reseña (Review)

Analysis of hidden node problem in LTE networks deployed in unlicensed spectrum

  • Campos, Pablo
  • Hernández-Solana, Ángela
  • Valdovinos-Bardají, Antonio
LTE operation in the unlicensed spectrum based on Licensed-Assisted Access (LAA) is being considered as an option to increase the capacity of 4G/5G wireless networks. This solution allows the eNodeB to contend with other nodes by accessing the shared medium and, through carrier aggregation (CA), to use both licensed and unlicensed bands to deliver best effort services. Nevertheless, the hidden node problem over shared medium access networks is an obstacle that must be addressed in order to reduce or avoid performance degradation problems. The metrics associated to LAA reflect the behavior of a node facing collisions. A better understanding of these metrics can help to identify nodes affected by hidden terminals, making it possible to take smart decisions about the continuity of a node on the unlicensed band, resulting in an improved network performance. In this paper, we first study the Channel Quality Indicator (CQI), Reference Signal Received Power (RSRP) and Reference Signal Received Quality (RSRQ) metrics on the context of LAA for a User Equipment (UE) that is facing different levels of interference. Then, a combination of the above metrics is used in order to develop an algorithm for collision detection. Finally, the performance of the algorithm is evaluated using a simulation tool under realistic channel conditions. The results show that is feasible to detect, with an adequate accuracy level, if a node is affected by collisions and subsequently if this node is located in hidden area. This is demonstrated with different levels of interference, realistic channel conditions and users in movement inside the hidden area.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

PSM-DMO: power save mode and discontinuous BLE mesh operation

  • Hernández Solana, Á.
  • Pérez Díaz de Cerio, D.
  • García-Lozano, M.
  • Valdovinos, A.
  • Valenzuela, J. L.
The Bluetooth Low Energy (BLE) mesh profile, standardized by the Bluetooth Special Interest Group (SIG), has an increasing interest in IoT solutions. However, the standard assumes that relay and friend nodes should be continuously scanning the channel awaiting any incoming transmissions. This could be very inefficient in terms of energy consumption, particularly in application scenarios where the backbone of the mesh network cannot be powered and traffic is infrequent. Hence, we present a novel strategy, named PSM-DMO, that minimizes the scan periods and thus, significantly reduces the overall energy consumption of the mesh network. PSM-DMO is defined as a new and optional feature for the currently published BLE mesh specifications, coexists with the standard operation, and is implemented without modifying the core of the specification. The proposal, that ensures the reliability of the mesh operation, can be used in BLE sensor networks that can tolerate a certain transmission delay. PSM-DMO replaces the continuous scan by a periodic but asynchronous polling process whereby the relay and sink nodes interrogate their neighbors about the existence of data to receive or to retransmit through the network. Nodes only go into scan mode during the period of time the mesh network will be involved in the transmission and dissemination. This period is estimated by the node which is the source of data, it is announced to its neighbors and it is propagated consecutively by all the relay nodes until the destination. PSM-DMO allows a theoretical reduction in the energy consumption of relay nodes up to 99.24 %.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

On the use of sniffers for spectrum occupancy measurements of Bluetooth low energy primary channels

  • Valenzuela-Pérez, A.
  • García-Lozano, M.
  • Valenzuela, J. L.
  • Pérez-Díaz-de-Cerio, D.
  • Hernández Solana, Á.
  • Valdovinos, A.
The methods usually employed to measure channel occupancy show limitations in the context of Bluetooth Low Energy (BLE) advertisements. We propose and analyze the use of BLE sniffers as light and portable low-cost spectrum occupancy meters to be used in scenarios where real time signal analyzers are not adequate. For the measurement technique to be successful, several low-level effects must be considered. The paper argues about on-air time, receiving blind times due to processing and intra system interference, buffer saturation and frequency anchoring. Hence, a compensation procedure based on collision rate estimation is proposed. Results with the refined method show that occupancies of 40% can be measured with an overestimation error whose percentile 95% is 5 percentage points. This is reduced to 1.9 points when the occupancy is 15%. The sniffers perform in real time and are shown to correctly track short term load variations. The strategy has been successfully used to characterize occupancy in highly variable and loaded scenarios such as subway platforms and a shopping mall. Values up to 25% have been observed, which implies a relevant packet error rate. Hence, the tool can be used to make agile audits and configure the parameters that control communication redundancy in new or existing networks.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Speeding Up Bluetooth Mesh

  • Perez-Diaz-de-Cerio, D
  • Hernandez-Solana, A
  • Garcia-Lozano, M
  • Bardaji, AV
  • Valenzuela, JL
Bluetooth has constantly evolved from its cradle in 1997 to the last 5.2 version in 2020. With each update and amendment, it has gained in speed, range, and versatility. One of the latest introductions was the Bluetooth Mesh Profile (BMP) making it a technology suitable for a wide variety of applications. Nevertheless, BMP was designed to maintain the compatibility with Bluetooth version 4 devices already deployed in the market. This imposes some restrictions that place Bluetooth Mesh under other competing technologies like Zigbee or Thread in terms of throughput performance. In this paper we propose two mechanisms to overcome these limitations and take advantage of the new extended advertising capabilities introduced with Bluetooth 5. These mechanisms are presented as modifications to the current protocol stack to allow the transmission of larger data structures. Thus, it is possible to boost the throughput of Bluetooth Mesh making it suitable to more demanding applications like, for example, image transmission. The first proposal is designed as an adaptation layer to avoid modifying the standard in its current form. The second makes minimal changes to the frame structure at the different layers enabling the user to accommodate possible encapsulations (i.e., tunneling) without incurring IPv6-layer fragmentation. We have analyzed both solutions and compared them with the current BMP in terms of throughput, delay, and energy consumption for different channel conditions and network size. The results show that except for very small messages or poor channel conditions the proposals improve the throughput and delay of the current BMP.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Triple-Band Concurrent Reconfigurable Matching Network

  • De Mingo, J
  • Carro, PL
  • Garcia-Ducar, P
  • Valdovinos, A
Reconfigurable Matching Networks (RMN) have found a wide range of applications, such as antenna impedance matching (Antenna Tuning Units -ATU-), the design of reconfigurable power amplifiers, applications in Magnetic Resonance Imaging (MRI), adjustable low noise amplifier design, etc. In this paper, we propose the experimental design and verification of a reconfigurable impedance synthesis network that can simultaneously work in three different bands and is completely independent so that the impedance variations in a frequency band are approximately transparent to the rest. The variable elements used in this paper are varactors. To verify its operation, it is applied to a process of matching a laser modulator in three different frequency bands for C-RAN (Cloud Radio Access Networks) applications. Experimental results demonstrate, as expected, that losses may depend on the state in which they are driven. Consequently, a state that can guarantee a good match could also imply greater losses, leading to a certain trade-off. The application of genetic algorithms in this context points out that it may be convenient to optimize the insertion losses of the complete chain instead of the return losses.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

BMADS: BLE Mesh Asynchronous Dynamic Scanning

  • Perez-Diaz-De-Cerio, D.
  • Valenzuela, J.L.
  • Garcia-Lozano, M.
  • Hernandez-Solana, A.
  • Valdovinos, A.
The Bluetooth low-energy (BLE) mesh profile, currently standardized by the Bluetooth Special Interest Group (SIG), assumes that friend and relay nodes should be continuously scanning the channel ready to receive any incoming transmissions (TXs). This is very inefficient in terms of energy consumption. Hence, we present BMADS, an asynchronous dynamic scanning mechanism designed to reduce the overall energy consumption of the mesh network. BMADS is implemented as a new feature for the currently published BLE mesh specifications without modifying its core. This feature reduces the scanning cycles of the nodes, but still ensuring the reliability. To make this possible, BMADS sends a new control message sequence before transmitting the data. This sequence puts the nodes into continuous scan mode, preparing the network for data TX. The proposal can be used in BLE sensor networks that can tolerate a certain TX delay and require especially low-energy consumption. BMADS allows a theoretical reduction in the energy consumption of the relay nodes up to 98%.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Machine Learning for Hidden Nodes Detection in Unlicensed LTE Networks

  • Campos, Pablo
  • Hernández-Solana, Ángela
  • Valdovinos-Bardají, Antonio
This paper analyzes and evaluates the use of Machine Learning (ML) techniques as an alternative to heuristic methods to identify UEs in Licensed-Assisted Access (LAA) networks that are being affected by collisions from hidden nodes sources. The paper analyzes different models based on supervised ML methods to classify UEs into two possible classes: UEs affected by collisions and UEs free of collisions. To implement them, we employ a set of typical parameters of the LTE standard, e.g., Channel Quality Indicator (CQI), Reference Signal Received Quality (RSRQ) and number of Physical Resource Blocks (PRB). These parameters are fed into different supervised ML models which, once optimized, obtain the best models to predict when an UE is facing interference from hidden nodes in a dynamic channel environment. Results show that classification methods based on ML techniques are capable of predicting with a high level of accuracy when a UE is affected by collisions and, consequently, if this node is located in a hidden area. Nevertheless, and despite the growing interest in applying ML techniques in an increasing number of fields, we can conclude that, in this case, the performance of the ML approach is not necessarily better than heuristic methods. For instance, it does not outperform the Dynamic Collision Detection (DCD) previously presented by the authors. In addition, the ML algorithms exhibit a higher prediction time and computational complexity, with respect to those obtained with DCD algorithm. This should be considered a drawback in some LTE-Advanced and 5G wireless network scenarios that prioritize lower latencies. © 2022