Pasar al contenido principal

SISTEMAS RADIANTES EN MILIMETRICAS Y SUBMILIMETRICAS PARA RADAR, COMUNICACIONES E IMAGENES.

TEC2013-47360-C3-1-P

•
Nombre agencia financiadora Ministerio de Economía y Competitividad
Acrónimo agencia financiadora MINECO
Programa Programa Estatal de Fomento de la Investigación Científica y Técnica de Excelencia
Subprograma Subprograma Estatal de Generación de Conocimiento
Convocatoria Proyectos de I+D (Excelencia / Generación de Conocimiento)
Año convocatoria 2013
Plan Estatal 2013-2016 Plan Estatal de Investigación Científica y Técnica y de Innovación
Unidad de gestión Secretaría de Estado de Educación, Formación Profesional y Universidades
Centro beneficiario UNIVERSITAT POLITECNICA DE CATALUNYA
Identificador persistente http://dx.doi.org/10.13039/501100003329

Resultados relacionados

Resultados totales (Incluyendo duplicados): 41
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Assessment of LTCC-Based Dielectric Flat Lens Antennas and Switched-Beam Arrays for Future 5G Millimeter-Wave Communication Systems

  • Imbert, Marc
  • Romeu, Jordi
  • Martinez-Ingles, Maria-Teresa
  • Molina-García-Pardo, José María
  • Jofre, Lluis
  • Baquero Escudero, Mariano|||0000-0001-8772-5431
[EN] This paper presents the design, low-temperature co-fired ceramics (LTCC) fabrication, and full experimental verification of novel dielectric flat lens antennas for future high data rate 5G wireless communication systems in the 60 GHz band. We introduce and practically completely evaluate and compare the performance of three different inhomogeneous gradient-index dielectric lenses with the effective parameters circularly and cylindrically distributed. These lenses, despite their planar profile antenna configuration, allow full 2-D beam scanning of high-gain radiation beams. A time-domain spectroscopy system is used to practically evaluate the permittivity profile achieved with the LTCC manufacturing process, obtaining very good results to confirm the viability of fabricating inhomogeneous flat lenses in a mass production technology. Then, the lenses performance is evaluated in terms of radiation pattern parameters, maximum gain, beam scanning, bandwidth performance, efficiencies, and impedance matching in the whole frequency band of interest. Finally, the performance of the three lenses is also experimentally evaluated and compared to a single omni-directional antenna and to a ten-element uniform linear array of omni-directional antennas in real 60 GHz wireless personal area network indoor line-of-sight (LOS) and obstructed-LOS environments, obtaining interesting and promising remarkable results in terms of measured received power and root-mean-square delay spread. At the end of this paper, an innovative switched-beam antenna array concept based on the presented cylindrically distributed effective parameters lens is also introduced and completely evaluated, confirming the potential applicability of the proposed antenna solution for future 5G wireless millimeter-wave communication system., This work was supported in part by the Spanish Inter-Ministerial Commission on Science and Technology (CICYT) under Projects TEC2013-47360-C3-1-P, TEC2013-47360-C3-2-P, and TEC2016-78028-C3-1-P, by FEDER and the Unidad de Excelencia Maria de Maeztu MDM-2016-0600, which is financed by the Agenda Estatal de Investigacion, Spain, and by the "Ministerio de Economia" through the FPI fellowship program.
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

A simple and effective microwave invisibility cloak based on frequency selective surfaces

  • Yuste, Pedro
  • Rius Casals, Juan Manuel|||0000-0003-0606-5422
  • Romeu Robert, Jordi|||0000-0003-0197-5961
  • Blanch Boris, Sebastián|||0000-0002-8757-583X
  • Heldring, Alexander|||0000-0003-2011-2096
  • Úbeda Farré, Eduard|||0000-0001-6759-0445
This paper presents the design, simulation, manufacturing and testing of a simple invisibility cloak based on a frequency selective surface (FSS). The work is focused on cloaking an electrically thin dielectric cylinder with an easy to manufacture FSS made of copper strips glued to the cylinder surface. In contrast to many papers in the literature, the full procedure from formulation to measurement results is presented here. An original approach to obtain the effective surface impedance of the cylindrical FSS from either simulated or measured far fields is introduced. The measurement results show excellent and relatively wide band performance of the cloak prototype., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

Electromagnetic monitoring of biological microorganisms

  • Zarrinkhat, Faezeh
  • Garrido, Alejandra
  • Jofre Roca, Lluís|||0000-0002-0547-901X
  • Romeu Robert, Jordi|||0000-0003-0197-5961
  • Rius Casals, Juan Manuel|||0000-0003-0606-5422
The investigation of the electromagnetic properties of biological cells in the microwave frequencies may enable wireless monitoring of functional activity of microorganisms. Both theoretical and experimental methodologies are applied to obtain the electromagnetic characterization of the E. Coli cells as a simple microorganism. The simulation and experimental results corresponding to the transmission coefficient and sensitivity of a coaxial set-up for different concentration of E. Coli cells are measured up to 3 GHz. Afterwards, the E. Coli is used as the basis to address the electromagnetic changes, in terms of extension and contrast, involved into the creation of a functional activity (action potential) of a neuronal cell., This work was supported by the Spanish ComisionInterministerial de Ciencia y Tecnologia (CICYT) un-der projects TEC2013-47360-C3-1-P, TEC2016-78028-C3-1-P, MDM2016-O6OO, and Catalan Research Group 2017 SGR219., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Comparative efficiency and power assessment of optical photoconductive material-based terahertz sources for wireless communication systems

  • Yazgan, Ayhan
  • Jofre Roca, Lluís|||0000-0002-0547-901X
  • Romeu Robert, Jordi|||0000-0003-0197-5961
Electronic version of an article published as [Journal of Circuits, Systems and Computers, vol. 28, num. 1, 2018] [https://doi.org/10.1142/S0218126619500051] © [copyright World Scientific Publishing Company] [https://www.worldscientific.com/worldscinet/jcsc], Terahertz band has recently attracted the attention of the communication society due to its huge bandwidth and very high-speed wireless communications capability. It has been utilized in a variety of disciplines including physics, biology and astronomy for years; and the main concerns have always been obtaining highly efficient and high-power terahertz sources. Today, these problems are still the most important issues in establishing an operable wireless terahertz communication link. In this paper, recent studies in the field of terahertz source design are investigated based on the terahertz output power and efficiency. Solid-state sources and optical sources were comparatively reviewed with optical photoconductive material (OPM)-based methods which are combined with the terahertz antennas in the design phase generally. For wireless communication, the most suitable frequencies are between 0.3THz and 1THz due to the attenuation profile of the atmosphere. For this reason, based on the recently published studies, it has been observed that OPM and resonant tunneling diode-based sources are the most promising terahertz sources in terms of efficiency and power. Key issues and the main problems of terahertz photoconductive antennas which are the base of OPM method were also discussed in this paper., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

3-D printed UWB microwave bodyscope for biomedical measurements

  • Rashid, Saba
  • Jofre Roca, Lluís|||0000-0002-0547-901X
  • Garrido, Alejandra
  • González, Giselle
  • Ding, Yongsheng
  • Aguasca Solé, Alberto|||0000-0003-2079-4322
  • O'Callaghan Castellà, Juan Manuel|||0000-0002-2740-0202
  • Romeu Robert, Jordi|||0000-0003-0197-5961
© 2019 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes,creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., In this letter, a three-dimensional (3-D) printed compact ultrawideband (UWB) extended gap ridge horn (EGRH) antenna designed to be used for biological measurements of the human body is described. The operational frequency covers the microwave band of interest from 0.5 to 3.0 GHz (for an S 11 under -7 dB). The 3-D printed EGRH antenna is dielectrically matched to the permittivity of the human body, and because of its compactness, it can be visualized as a general-purpose microwave probe among the RF biomedical community. The probe has proven its capability as a pass-through propagation sensor for different parts of the human body and as a sensor detecting a 1 cm diameter object placed inside an artificial head phantom., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

On the accuracy of the adaptive cross aproximation algorithm

  • Heldring, Alexander|||0000-0003-2011-2096
  • Úbeda Farré, Eduard|||0000-0001-6759-0445
  • Sekulic, Ivan
  • Rius Casals, Juan Manuel|||0000-0003-0606-5422
© 2017 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes,creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., This contribution identifies an often ignored source of uncertainty in the accuracy of the adaptive cross approximation algorithm, and proposes a combination of adaptations that reduce this uncertainty with negligible additional computational cost., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Three-Dimensional beamsteering low complexity reconfigurable multilevel antenna

  • Zhou, Ivan
  • Ramírez Arroyave, Germán Augusto
  • Montero Bayo, Luca
  • Blanch Boris, Sebastián|||0000-0002-8757-583X
  • Romeu Robert, Jordi|||0000-0003-0197-5961
  • Jofre Roca, Lluís|||0000-0002-0547-901X
© 2020 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes,creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., A low-complexity reconfigurable antenna (RA) capable of steering its beam into nine different directions corresponding to ¿={-42°,0°,42°} in the ¿={25°,0°,155°} planes, and ¿=±25° in the ¿=90° plane, using a reduced number of switches is presented. The RA operating at 3.4-3.8 GHz consists of a central dipole element excited by a coaxial probe, surrounded by four switchable parasitic dipoles located at different height levels above a ground plane, which acts as either a reflector for the elements located at an upper layer or a director for the ones at a lower layer, improving the radiation characteristics of the antenna. Each parasitic dipole is fed with a p-i-n diode as a switch, which enables the activation of these elements providing the desired modes of operation. The presented RA was manufactured and measured showing results with a good agreement with the theoretical and numerical simulation., This work was supported by the Spanish “ComisionInterministerial de Ciencia y Tecnologia” (CICYT) un-der projects TEC2013-47360-C3-1-P, TEC2016-78028-C3-1-P and MDM2016-0600, and Catalan Research Group 2017SGR 219, Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

A figure of merit to assess the performance of photoconductive antennas at terahertz band

  • Romeu Robert, Jordi|||0000-0003-0197-5961
  • Cea Falcó, Marc de
  • Jofre Roca, Lluís|||0000-0002-0547-901X
  • Yazgan, Ahmet Utku
Photoconductive antennas are one of the most efficient ways to radiate and receive EM waves around the 1 THz frequency band. The physical processes involved in photoconductive terahertz signal generation are complex enough to prevent having simple and accurate models to assess the performance of different electrode geometries. In this paper a figure of merit definition based on the physical processes involved in the electro-optical conversion process is proposed.
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

GEROS-ISS, a demonstration mission of GNSS remote sensing capabilities to derive geophysical parameters of the earth surfaces: performance evaluation

  • Camps Carmona, Adriano José|||0000-0002-9514-4992
  • Hyuk, Park|||0000-0003-0031-0802
  • Ghavidel, Ali
  • Rius Casals, Juan Manuel|||0000-0003-0606-5422
  • Sekulic, Ivan
The GNSS rEflectometry, Radio Occultation and Scatterometry onboard International Space Station (GEROS-ISS) is an innovative experiment for climate research, proposed in 2011 within a call of the European Space Agency (ESA) for installation at the ISS. This international proposal was the only one selected for further studies by ESA out of ~25 submitted ones. In this work, the assessment of the instrument performance for the near-nadir altimetry (GNSS-R) mode is assessed, including the effects of multi-path in the ISS structure, the electromagnetic-bias, and the orbital height decay. In the absence of ionospheric scintillations, the altimetry rms error is <; 50 cm for a swath <; ~250 km and for U10 <; 10 m/s. If the transmitted power is 3 dB higher (likely to happen at beginning of life of the spacecraft), mission requirements (rms error is <; 50 cm) are met for all ISS heights and U10 up to 15 m/s. However, around 1.5 GHz, the ionosphere can induce significant fading, from 2 to > 20 dB at equatorial regions, mainly after sunset, which will seriously degrade the altimetry and the scatterometry performances of the instrument., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

The state of art of terahertz sources: a communication perspective at a glance

  • Yazgan, Ayhan
  • Jofre Roca, Lluís|||0000-0002-0547-901X
  • Romeu Garbí, Jordi|||0000-0002-9075-6877
Terahertz band lying between infrared and microwave is a very promising part of electromagnetic spectrum for spectroscopy, space applications and different kind of imaging applications such as medical and security. Recently, this special band has attracted the attention of communication society because of its huge bandwidth and therefore ability of very high speed wireless communications. One of the challenges still on the table is to obtain efficient terahertz sources. In this paper, recent studies on the topic of efficient terahertz sources are reviewed comparatively. Especially for the communication concept, taking into account the efficiency, it can be said that the trend goes to the optical photoconductive materials method including plasmonic electrodes., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

Simultaneously improving the efficiency and compression of the adaptive cross approximation algorithm

  • Heldring, Alexander|||0000-0003-2011-2096
  • Úbeda Farré, Eduard|||0000-0001-6759-0445
  • Rius Casals, Juan Manuel|||0000-0003-0606-5422
This paper proposes an adaptation of the conventional ACA algorithm for block-wise impedance matrix compression, yielding a substantial speed-up as well as a higher compression rate. The recently published stochastic Frobenius norm estimation is complemented with a new approach to allow applying it to blocks that represent touching regions. The stochastic method is then combined with SVD recompression to simultaneously eliminate the stochastic uncertainty and optimize the compression rate., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

Efficient analysis of homogeneous dielectric and plasmonic media with integral equation MEI (IE-MEI)

  • Rius Casals, Juan Manuel|||0000-0003-0606-5422
  • Planes Conangla, Gerard
  • Úbeda Farré, Eduard|||0000-0001-6759-0445
  • Heldring, Alexander|||0000-0003-2011-2096
This paper revisits the IE-MEI method and proposes a new formulation for high-loss dielectric piecewise-homogeneous media. The aim of this work is to assess if the fast attenuation of fields in highly lossy media helps in improving the not successful performance of IE-MEI for lossless dielectric scatterers., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

Frequency extrapolation of IE-MEI linear system Coefficients in 2D

  • Rius Casals, Juan Manuel|||0000-0003-0606-5422
  • Heldring, Alexander|||0000-0003-2011-2096
  • Úbeda Farré, Eduard|||0000-0001-6759-0445
The Integral Equation MEI (IE-MEI) method for the sparsification of Method of Moments linear system matrix is revisited here. It achieves cpu computation time and storage memory requirements of order O(N ) (for 2D perfectly conducting scatterers of arbitrary convex shape), which is –to our knowledge– the best asymptotic computational complexity ever achieved by integral equation methods. The aim of this paper is to present yet unpublished details of the algorithm to extrapolate the linear system coefficients and the latest results obtained using modern computers., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Debye frequency-extended waveguide permittivity extraction for high complex permittivity materials. Concrete setting process characterization

  • Gonzalez, Giselle
  • Blanch Boris, Sebastián|||0000-0002-8757-583X
  • Romeu Robert, Jordi|||0000-0003-0197-5961
  • Jofre Roca, Lluís|||0000-0002-0547-901X
© 2019 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes,creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., A waveguide with central frequency 868 MHz is used in transmission/reflection operation regime to accurately measure the behaviour of the complex permittivity of high complex permittivity granular materials and it has been frequency-extended up to 3 GHz using the Debye fitted relaxation model. It is shown that for highly granular high permittivity materials a waveguide based transmission/reflection technique is necessary to reduce the uncertainty of the extracted permittivity values. The technique is first described and validated with isopropyl alcohol and then applied to the characterization of cement based materials. This paper provides accurate data on the evolution of the complex permittivity of concrete and mortar from the moment of pouring until air dried condition is achieved., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Enhanced discretization of surface integral equations for resonant scattering analysis of sharp-edged plasmonic nanoparticles

  • Sekulic, Ivan
  • Tzarouchis, Dimitrios C.
  • Ylä-Oijala, Pasi
  • Úbeda Farré, Eduard|||0000-0001-6759-0445
  • Rius Casals, Juan Manuel|||0000-0003-0606-5422
The surface integral equation (SIE) method, discretized with the method of moments, is a well-established methodology for the scattering analysis of subwavelength plasmonic nanoparticles. SIEs are usually discretized with low-order basis functions that preserve the normal continuity of the surface currents across the edges arising in the meshed boundary, such as Rao-Wilton-Glisson (RWG) functions. However, the plasmonic enhancement modeling on sharp-edged particles is an extremely challenging task, especially due to the singular fields exerted at sharp corners, exposing a slow (or no) convergence in the computation of the scattering and absorption spectra. In this paper, we propose an alternative discretization strategy based on a discontinuous basis function set in conjunction with a volumetric-tetrahedral testing scheme. We demonstrate the potential of the proposed discretization scheme by studying scattering and absorption spectra of three canonical plasmonic polyhedra, i.e., a hexahedral, an octahedral, and a tetrahedral silver inclusion. The results expose an improved accuracy and faster convergence in both far-field and near-field regions when compared to the standard RWG implementation. The proposed discretization scheme can offer faster and more accurate routes towards the exploration and design of the plasmonic resonant spectrum of sharp-edged nanoparticles and nanoantennas., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Reconfigurable dual-polarized beam-steering broadband antenna using a crossed-strips geometry

  • Ramírez Arroyave, Germán Augusto
  • Zhou, Ivan
  • Blanch Boris, Sebastián|||0000-0002-8757-583X
  • Towfiq, Asaduzzaman
  • Cetiner, Bedri Artug
  • Romeu Robert, Jordi|||0000-0003-0197-5961
  • Jofre Roca, Lluís|||0000-0002-0547-901X
In this letter, a reconfigurable dual-polarized broadband antenna with beam-steering capabilities using a parasitic layer is proposed for 5G new radio (NR) frequency range 1 (FR-1) applications. The antenna is a dual-port aperture-stacked patch structure with symmetrical orthogonal (horizontal and vertical) currents. The beam-steering is achieved by a pair of reconfigurable cross-shaped parasitic strips, which bestow the antenna three main beam directions θ = { ~ -25 ° ,0 ° , ~ 25 ° }, Ψ = {0 ° } with pointing and gain (7 dB) stability across a 30% impedance bandwidth (S 11 , S 22 <; -10 dB) from 3.2 - 4.3 GHz for both ports/polarizations. A prototype of the antenna is manufactured and measured demonstrating results in accordance with simulation expectations., This work was supported in part by Colombian “Departamento Administrativo de Ciencia, Tecnología e Innovación” Colciencias through convocatoria 727 of 2015 scholarship, and in part by the Spanish “Comision Interministerial de Ciencia y Tecnologia” (CICYT) under Projects TEC2013-47360-C3-1-P/AEI/10.13039/501100011033, TEC2016-78028-C3- 1-P/AEI/10.13039/501100011033, and MDM2016-0600, and Catalan Research Group 2017 SGR 219., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

An architecture analysis for millimeter-wave optically steerable antenna array

  • Ballesteros Sánchez, Christian|||0000-0002-4395-9057
  • Maestre, Marcos
  • Santos Blanco, M. Concepción|||0000-0002-5103-5356
  • Romeu Robert, Jordi|||0000-0003-0197-5961
  • Jofre Roca, Lluís|||0000-0002-0547-901X
A lens-based integrated photodiode-antenna array for a Radio over Fiber (RoF) 5G wireless base station at millimeter-wave frequencies is proposed and analyzed. The elements of the array are based on slot bow-tie antennas which ensure a good matching to the photodiode impedance measurements in a band that extends from 23 to 35 GHz. Simulated far-field patterns show that beam steering in 23.5° steps with a minimum peak gain of 15.8 dB may be achieved by means of an optical switch in a 4-element array with 3.8 mm spacing using an Acrylonitrile Butadiene Styrene (ABS) extended hemispherical lens with 25 mm radius., This work was supported by the Spanish "Comision Interministerial de Ciencia y Tecnologia" (CICYT) under projects TEC2013-47360-C3-1-P, TEC2016-78028-C3-1-P and MDM2016-O6OO, and Catalan Research Group 2017 SGR 219. The Spanish Ministry of Education also contributes via a doctoral grant to the first author (FPU17/05561)., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

High impedance monopole antenna for indoor terahertz communication system

  • Yazgan, Ayhan
  • Romeu Robert, Jordi|||0000-0003-0197-5961
  • Jofre Roca, Lluís|||0000-0002-0547-901X
In this study, a wideband terahertz antenna for indoor wireless communication systems is proposed. Antenna has high input impedance which is reasonable for terahertz systems due to the high output impedance of terahertz sources. Proposed antenna has been designed to operate in 0.67 THz which is one of the appropriate frequencies considering the atmospheric attenuation conditions for short range indoor terahertz wireless communication systems. Designed antenna has 0.8 kohm input impedance at the center of the band and approximately 100 GHz -10 dB bandwidth at 0.67 THz., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

Variable capacitive antenna loading for embedded RFID sensors

  • Gonzalez, Giselle
  • Jofre Roca, Lluís|||0000-0002-0547-901X
  • Romeu Robert, Jordi|||0000-0003-0197-5961
  • Cairó Molins, Josep Ignasi|||0000-0002-8493-7874
In this paper, a self-adaptive folded dipole antenna to work embedded in media with changing physical and chemical properties for RFID applications is proposed. Self-adaptability is provided by taking advantage of the dual-mode behaviour of the folded dipole antenna where variable capacitance diodes are strategically placed to compensate for the change produced in the electromagnetic properties of the embedding medium. The presented antenna has been optimized at 868MHz., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

On the accuracy of the Adaptive Cross Approximation algorithm

  • Heldring, Alexander|||0000-0003-2011-2096
  • Úbeda Farré, Eduard|||0000-0001-6759-0445
  • Rius Casals, Juan Manuel|||0000-0003-0606-5422
This contribution identifies an often ignored source of uncertainty in the accuracy of the Adaptive Cross Approximation (ACA) algorithm.
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Beam management for vehicle-to-vehicle (V2V) communications in millimeter wave 5G

  • Montero Bayo, Luca
  • Ballesteros Sánchez, Christian|||0000-0002-4395-9057
  • De Marco, Cesar
  • Jofre Roca, Lluís|||0000-0002-0547-901X
Cooperative, Connected and Automated Mobility (CCAM) is expected to leverage the full potential of wireless communications. With the growing adoption of 5G and its support for Vehicle-to-Everything (V2X) communications, beamformed vehicular communications at millimeter-wave (mmWave) bands are expected to enable the most demanding connected driving applications. Beamformed V2X links present the challenge of beam management in such a fast-changing scenario. This paper goes through the practical limitations of the 5G V2X stack to support successful beamforming procedures. Two beam management strategies are proposed. Both strategies are evaluated in terms of power performance, beam recovery time and channel usage. The results suggest that significant differences apply when the beam is more frequently updated, whereas little improvement is seen by increasing the size of the beamset. Also, the selection of a proper strategy is shown to be important to alleviate the channel from overheads, and substantial differences in required signaling can be seen depending on the beam-tracking approach., This work was partly funded by the Spanish Comisión Interministerial de Ciencia y Tecnología under projects TEC2013-47360- C3-1-P, TEC2016-78028-C3-1-P and MDM2016-0600, and Catalan Research Group 2017 SGR 219. The Spanish Ministry of Education (FPU17/05561) and Generalitat de Catalunya DI programme (2018- DI-084) also contribute with predoctoral grants for the authors., Peer Reviewed
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

On the accuracy of the adaptive cross aproximation algorithm

  • Heldring, Alexander
  • Úbeda Farré, Eduard
  • Sekulic, Ivan
  • Rius Casals, Juan Manuel
© 2017 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes,creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., This contribution identifies an often ignored source of uncertainty in the accuracy of the adaptive cross approximation algorithm, and proposes a combination of adaptations that reduce this uncertainty with negligible additional computational cost., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

A simple and effective microwave invisibility cloak based on frequency selective surfaces

  • Yuste, Pedro
  • Rius Casals, Juan Manuel
  • Romeu Robert, Jordi
  • Blanch Boris, Sebastián
  • Heldring, Alexander
  • Úbeda Farré, Eduard
This paper presents the design, simulation, manufacturing and testing of a simple invisibility cloak based on a frequency selective surface (FSS). The work is focused on cloaking an electrically thin dielectric cylinder with an easy to manufacture FSS made of copper strips glued to the cylinder surface. In contrast to many papers in the literature, the full procedure from formulation to measurement results is presented here. An original approach to obtain the effective surface impedance of the cylindrical FSS from either simulated or measured far fields is introduced. The measurement results show excellent and relatively wide band performance of the cloak prototype., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Frequency extrapolation of IE-MEI linear system Coefficients in 2D

  • Rius Casals, Juan Manuel
  • Heldring, Alexander
  • Úbeda Farré, Eduard
The Integral Equation MEI (IE-MEI) method for the sparsification of Method of Moments linear system matrix is revisited here. It achieves cpu computation time and storage memory requirements of order O(N ) (for 2D perfectly conducting scatterers of arbitrary convex shape), which is –to our knowledge– the best asymptotic computational complexity ever achieved by integral equation methods. The aim of this paper is to present yet unpublished details of the algorithm to extrapolate the linear system coefficients and the latest results obtained using modern computers., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Beam management for vehicle-to-vehicle (V2V) communications in millimeter wave 5G

  • Montero Bayo, Luca
  • Ballesteros Sánchez, Christian
  • De Marco, Cesar
  • Jofre Roca, Lluís
Cooperative, Connected and Automated Mobility (CCAM) is expected to leverage the full potential of wireless communications. With the growing adoption of 5G and its support for Vehicle-to-Everything (V2X) communications, beamformed vehicular communications at millimeter-wave (mmWave) bands are expected to enable the most demanding connected driving applications. Beamformed V2X links present the challenge of beam management in such a fast-changing scenario. This paper goes through the practical limitations of the 5G V2X stack to support successful beamforming procedures. Two beam management strategies are proposed. Both strategies are evaluated in terms of power performance, beam recovery time and channel usage. The results suggest that significant differences apply when the beam is more frequently updated, whereas little improvement is seen by increasing the size of the beamset. Also, the selection of a proper strategy is shown to be important to alleviate the channel from overheads, and substantial differences in required signaling can be seen depending on the beam-tracking approach., This work was partly funded by the Spanish Comisión Interministerial de Ciencia y Tecnología under projects TEC2013-47360- C3-1-P, TEC2016-78028-C3-1-P and MDM2016-0600, and Catalan Research Group 2017 SGR 219. The Spanish Ministry of Education (FPU17/05561) and Generalitat de Catalunya DI programme (2018- DI-084) also contribute with predoctoral grants for the authors., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

GEROS-ISS, a demonstration mission of GNSS remote sensing capabilities to derive geophysical parameters of the earth surfaces: performance evaluation

  • Camps Carmona, Adriano José
  • Hyuk, Park
  • Ghavidel, Ali
  • Rius Casals, Juan Manuel
  • Sekulic, Ivan
The GNSS rEflectometry, Radio Occultation and Scatterometry onboard International Space Station (GEROS-ISS) is an innovative experiment for climate research, proposed in 2011 within a call of the European Space Agency (ESA) for installation at the ISS. This international proposal was the only one selected for further studies by ESA out of ~25 submitted ones. In this work, the assessment of the instrument performance for the near-nadir altimetry (GNSS-R) mode is assessed, including the effects of multi-path in the ISS structure, the electromagnetic-bias, and the orbital height decay. In the absence of ionospheric scintillations, the altimetry rms error is <; 50 cm for a swath <; ~250 km and for U10 <; 10 m/s. If the transmitted power is 3 dB higher (likely to happen at beginning of life of the spacecraft), mission requirements (rms error is <; 50 cm) are met for all ISS heights and U10 up to 15 m/s. However, around 1.5 GHz, the ionosphere can induce significant fading, from 2 to > 20 dB at equatorial regions, mainly after sunset, which will seriously degrade the altimetry and the scatterometry performances of the instrument., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

High impedance monopole antenna for indoor terahertz communication system

  • Yazgan, Ayhan
  • Romeu Robert, Jordi
  • Jofre Roca, Lluís
In this study, a wideband terahertz antenna for indoor wireless communication systems is proposed. Antenna has high input impedance which is reasonable for terahertz systems due to the high output impedance of terahertz sources. Proposed antenna has been designed to operate in 0.67 THz which is one of the appropriate frequencies considering the atmospheric attenuation conditions for short range indoor terahertz wireless communication systems. Designed antenna has 0.8 kohm input impedance at the center of the band and approximately 100 GHz -10 dB bandwidth at 0.67 THz., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Reconfigurable dual-polarized beam-steering broadband antenna using a crossed-strips geometry

  • Ramírez Arroyave, Germán Augusto
  • Zhou, Ivan
  • Blanch Boris, Sebastián
  • Towfiq, Asaduzzaman
  • Cetiner, Bedri Artug
  • Romeu Robert, Jordi
  • Jofre Roca, Lluís
In this letter, a reconfigurable dual-polarized broadband antenna with beam-steering capabilities using a parasitic layer is proposed for 5G new radio (NR) frequency range 1 (FR-1) applications. The antenna is a dual-port aperture-stacked patch structure with symmetrical orthogonal (horizontal and vertical) currents. The beam-steering is achieved by a pair of reconfigurable cross-shaped parasitic strips, which bestow the antenna three main beam directions θ = { ~ -25 ° ,0 ° , ~ 25 ° }, Ψ = {0 ° } with pointing and gain (7 dB) stability across a 30% impedance bandwidth (S 11 , S 22 <; -10 dB) from 3.2 - 4.3 GHz for both ports/polarizations. A prototype of the antenna is manufactured and measured demonstrating results in accordance with simulation expectations., This work was supported in part by Colombian “Departamento Administrativo de Ciencia, Tecnología e Innovación” Colciencias through convocatoria 727 of 2015 scholarship, and in part by the Spanish “Comision Interministerial de Ciencia y Tecnologia” (CICYT) under Projects TEC2013-47360-C3-1-P/AEI/10.13039/501100011033, TEC2016-78028-C3- 1-P/AEI/10.13039/501100011033, and MDM2016-0600, and Catalan Research Group 2017 SGR 219., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

3-D printed UWB microwave bodyscope for biomedical measurements

  • Rashid, Saba
  • Jofre Roca, Lluís
  • Garrido, Alejandra
  • González, Giselle
  • Ding, Yongsheng
  • Aguasca Solé, Alberto
  • O'Callaghan Castellà, Juan Manuel
  • Romeu Robert, Jordi
© 2019 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes,creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., In this letter, a three-dimensional (3-D) printed compact ultrawideband (UWB) extended gap ridge horn (EGRH) antenna designed to be used for biological measurements of the human body is described. The operational frequency covers the microwave band of interest from 0.5 to 3.0 GHz (for an S 11 under -7 dB). The 3-D printed EGRH antenna is dielectrically matched to the permittivity of the human body, and because of its compactness, it can be visualized as a general-purpose microwave probe among the RF biomedical community. The probe has proven its capability as a pass-through propagation sensor for different parts of the human body and as a sensor detecting a 1 cm diameter object placed inside an artificial head phantom., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Efficient analysis of homogeneous dielectric and plasmonic media with integral equation MEI (IE-MEI)

  • Rius Casals, Juan Manuel
  • Planes Conangla, Gerard
  • Úbeda Farré, Eduard
  • Heldring, Alexander
This paper revisits the IE-MEI method and proposes a new formulation for high-loss dielectric piecewise-homogeneous media. The aim of this work is to assess if the fast attenuation of fields in highly lossy media helps in improving the not successful performance of IE-MEI for lossless dielectric scatterers., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Simultaneously improving the efficiency and compression of the adaptive cross approximation algorithm

  • Heldring, Alexander
  • Úbeda Farré, Eduard
  • Rius Casals, Juan Manuel
This paper proposes an adaptation of the conventional ACA algorithm for block-wise impedance matrix compression, yielding a substantial speed-up as well as a higher compression rate. The recently published stochastic Frobenius norm estimation is complemented with a new approach to allow applying it to blocks that represent touching regions. The stochastic method is then combined with SVD recompression to simultaneously eliminate the stochastic uncertainty and optimize the compression rate., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

On the accuracy of the Adaptive Cross Approximation algorithm

  • Heldring, Alexander
  • Úbeda Farré, Eduard
  • Rius Casals, Juan Manuel
This contribution identifies an often ignored source of uncertainty in the accuracy of the Adaptive Cross Approximation (ACA) algorithm., Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Three-Dimensional beamsteering low complexity reconfigurable multilevel antenna

  • Zhou, Ivan
  • Ramírez Arroyave, Germán Augusto
  • Montero Bayo, Luca
  • Blanch Boris, Sebastián
  • Romeu Robert, Jordi
  • Jofre Roca, Lluís
© 2020 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes,creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., A low-complexity reconfigurable antenna (RA) capable of steering its beam into nine different directions corresponding to ¿={-42°,0°,42°} in the ¿={25°,0°,155°} planes, and ¿=±25° in the ¿=90° plane, using a reduced number of switches is presented. The RA operating at 3.4-3.8 GHz consists of a central dipole element excited by a coaxial probe, surrounded by four switchable parasitic dipoles located at different height levels above a ground plane, which acts as either a reflector for the elements located at an upper layer or a director for the ones at a lower layer, improving the radiation characteristics of the antenna. Each parasitic dipole is fed with a p-i-n diode as a switch, which enables the activation of these elements providing the desired modes of operation. The presented RA was manufactured and measured showing results with a good agreement with the theoretical and numerical simulation., This work was supported by the Spanish “ComisionInterministerial de Ciencia y Tecnologia” (CICYT) un-der projects TEC2013-47360-C3-1-P, TEC2016-78028-C3-1-P and MDM2016-0600, and Catalan Research Group 2017SGR 219, Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

An architecture analysis for millimeter-wave optically steerable antenna array

  • Ballesteros Sánchez, Christian
  • Maestre, Marcos
  • Santos Blanco, M. Concepción
  • Romeu Robert, Jordi
  • Jofre Roca, Lluís
A lens-based integrated photodiode-antenna array for a Radio over Fiber (RoF) 5G wireless base station at millimeter-wave frequencies is proposed and analyzed. The elements of the array are based on slot bow-tie antennas which ensure a good matching to the photodiode impedance measurements in a band that extends from 23 to 35 GHz. Simulated far-field patterns show that beam steering in 23.5° steps with a minimum peak gain of 15.8 dB may be achieved by means of an optical switch in a 4-element array with 3.8 mm spacing using an Acrylonitrile Butadiene Styrene (ABS) extended hemispherical lens with 25 mm radius., This work was supported by the Spanish "Comision Interministerial de Ciencia y Tecnologia" (CICYT) under projects TEC2013-47360-C3-1-P, TEC2016-78028-C3-1-P and MDM2016-O6OO, and Catalan Research Group 2017 SGR 219. The Spanish Ministry of Education also contributes via a doctoral grant to the first author (FPU17/05561)., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Enhanced discretization of surface integral equations for resonant scattering analysis of sharp-edged plasmonic nanoparticles

  • Sekulic, Ivan
  • Tzarouchis, Dimitrios C.
  • Ylä-Oijala, Pasi
  • Úbeda Farré, Eduard
  • Rius Casals, Juan Manuel
The surface integral equation (SIE) method, discretized with the method of moments, is a well-established methodology for the scattering analysis of subwavelength plasmonic nanoparticles. SIEs are usually discretized with low-order basis functions that preserve the normal continuity of the surface currents across the edges arising in the meshed boundary, such as Rao-Wilton-Glisson (RWG) functions. However, the plasmonic enhancement modeling on sharp-edged particles is an extremely challenging task, especially due to the singular fields exerted at sharp corners, exposing a slow (or no) convergence in the computation of the scattering and absorption spectra. In this paper, we propose an alternative discretization strategy based on a discontinuous basis function set in conjunction with a volumetric-tetrahedral testing scheme. We demonstrate the potential of the proposed discretization scheme by studying scattering and absorption spectra of three canonical plasmonic polyhedra, i.e., a hexahedral, an octahedral, and a tetrahedral silver inclusion. The results expose an improved accuracy and faster convergence in both far-field and near-field regions when compared to the standard RWG implementation. The proposed discretization scheme can offer faster and more accurate routes towards the exploration and design of the plasmonic resonant spectrum of sharp-edged nanoparticles and nanoantennas., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Comparative efficiency and power assessment of optical photoconductive material-based terahertz sources for wireless communication systems

  • Yazgan, Ayhan
  • Jofre Roca, Lluís
  • Romeu Robert, Jordi
Electronic version of an article published as [Journal of Circuits, Systems and Computers, vol. 28, num. 1, 2018] [https://doi.org/10.1142/S0218126619500051] © [copyright World Scientific Publishing Company] [https://www.worldscientific.com/worldscinet/jcsc], Terahertz band has recently attracted the attention of the communication society due to its huge bandwidth and very high-speed wireless communications capability. It has been utilized in a variety of disciplines including physics, biology and astronomy for years; and the main concerns have always been obtaining highly efficient and high-power terahertz sources. Today, these problems are still the most important issues in establishing an operable wireless terahertz communication link. In this paper, recent studies in the field of terahertz source design are investigated based on the terahertz output power and efficiency. Solid-state sources and optical sources were comparatively reviewed with optical photoconductive material (OPM)-based methods which are combined with the terahertz antennas in the design phase generally. For wireless communication, the most suitable frequencies are between 0.3THz and 1THz due to the attenuation profile of the atmosphere. For this reason, based on the recently published studies, it has been observed that OPM and resonant tunneling diode-based sources are the most promising terahertz sources in terms of efficiency and power. Key issues and the main problems of terahertz photoconductive antennas which are the base of OPM method were also discussed in this paper., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

The state of art of terahertz sources: a communication perspective at a glance

  • Yazgan, Ayhan
  • Jofre Roca, Lluís
  • Romeu Garbí, Jordi
Terahertz band lying between infrared and microwave is a very promising part of electromagnetic spectrum for spectroscopy, space applications and different kind of imaging applications such as medical and security. Recently, this special band has attracted the attention of communication society because of its huge bandwidth and therefore ability of very high speed wireless communications. One of the challenges still on the table is to obtain efficient terahertz sources. In this paper, recent studies on the topic of efficient terahertz sources are reviewed comparatively. Especially for the communication concept, taking into account the efficiency, it can be said that the trend goes to the optical photoconductive materials method including plasmonic electrodes., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Variable capacitive antenna loading for embedded RFID sensors

  • Gonzalez, Giselle
  • Jofre Roca, Lluís
  • Romeu Robert, Jordi
  • Cairó Molins, Josep Ignasi
In this paper, a self-adaptive folded dipole antenna to work embedded in media with changing physical and chemical properties for RFID applications is proposed. Self-adaptability is provided by taking advantage of the dual-mode behaviour of the folded dipole antenna where variable capacitance diodes are strategically placed to compensate for the change produced in the electromagnetic properties of the embedding medium. The presented antenna has been optimized at 868MHz., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

A figure of merit to assess the performance of photoconductive antennas at terahertz band

  • Romeu Robert, Jordi
  • Cea Falcó, Marc de
  • Jofre Roca, Lluís
  • Yazgan, Ahmet Utku
Photoconductive antennas are one of the most efficient ways to radiate and receive EM waves around the 1 THz frequency band. The physical processes involved in photoconductive terahertz signal generation are complex enough to prevent having simple and accurate models to assess the performance of different electrode geometries. In this paper a figure of merit definition based on the physical processes involved in the electro-optical conversion process is proposed., Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Electromagnetic monitoring of biological microorganisms

  • Zarrinkhat, Faezeh
  • Garrido, Alejandra
  • Jofre Roca, Lluís
  • Romeu Robert, Jordi
  • Rius Casals, Juan Manuel
The investigation of the electromagnetic properties of biological cells in the microwave frequencies may enable wireless monitoring of functional activity of microorganisms. Both theoretical and experimental methodologies are applied to obtain the electromagnetic characterization of the E. Coli cells as a simple microorganism. The simulation and experimental results corresponding to the transmission coefficient and sensitivity of a coaxial set-up for different concentration of E. Coli cells are measured up to 3 GHz. Afterwards, the E. Coli is used as the basis to address the electromagnetic changes, in terms of extension and contrast, involved into the creation of a functional activity (action potential) of a neuronal cell., This work was supported by the Spanish ComisionInterministerial de Ciencia y Tecnologia (CICYT) un-der projects TEC2013-47360-C3-1-P, TEC2016-78028-C3-1-P, MDM2016-O6OO, and Catalan Research Group 2017 SGR219., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Debye frequency-extended waveguide permittivity extraction for high complex permittivity materials. Concrete setting process characterization

  • Gonzalez, Giselle
  • Blanch Boris, Sebastián
  • Romeu Robert, Jordi
  • Jofre Roca, Lluís
© 2019 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes,creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., A waveguide with central frequency 868 MHz is used in transmission/reflection operation regime to accurately measure the behaviour of the complex permittivity of high complex permittivity granular materials and it has been frequency-extended up to 3 GHz using the Debye fitted relaxation model. It is shown that for highly granular high permittivity materials a waveguide based transmission/reflection technique is necessary to reduce the uncertainty of the extracted permittivity values. The technique is first described and validated with isopropyl alcohol and then applied to the characterization of cement based materials. This paper provides accurate data on the evolution of the complex permittivity of concrete and mortar from the moment of pouring until air dried condition is achieved., Peer Reviewed, Postprint (author's final draft)