Pasar al contenido principal

SISTEMA INTEGRADOS INALAMBRICOS EN MICROONDAS, MILIMETRICAS Y TERAHERCIOS PARA COMUNICACIONES SENSORIZACION

TEC2016-78028-C3-1-P

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal de Fomento de la Investigación Científica y Técnica de Excelencia
Subprograma Subprograma Estatal de Generación de Conocimiento
Convocatoria Proyectos de I+D (Excelencia / Generación de Conocimiento)
Año convocatoria 2016
Plan Estatal 2013-2016 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario UNIVERSITAT POLITECNICA DE CATALUNYA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 53
Encontrada(s) 1 página(s)

Repositorio Digital de la UPF
Publicación Artículo científico (JournalArticle)

Dielectric properties of colon polyps, cancer, and normal mucosa: Ex vivo measurements from 0.5 to 20 GHz

  • Guardiola, Marta
  • Buitrago, Santiago
  • Fernández-Esparrach, Gloria
  • O’Callaghan, Joan M.
  • Romeu, Jordi
  • Cuatrecasas, Miriam
  • Córdova, Henry
  • González Ballester, Miguel Ángel, 1973-
  • Camara, Oscar
Purpose: Colorectal cancer is highly preventable by detecting and removing polyps, which are the precursors. Currently, the most accurate test is colonoscopy, but still misses 22% of polyps due to visualization limitations. In this paper, we preliminary assess the potential of microwave imaging and dielectric properties (e.g., complex permittivity) as a complementary method for detecting polyps and cancer tissue in the colon. The dielectric properties of biological tissues have been used in a wide variety of applications, including safety assessment of wireless technologies and design of medical diagnostic or therapeutic techniques (microwave imaging, hyperthermia, and ablation). The main purpose of this work is to measure the complex permittivity of different types of colon polyps, cancer, and normal mucosa in ex vivo human samples to study if the dielectric properties are appropriate for classification purposes. Methods: The complex permittivity of freshly excised healthy colon tissue, cancer, and histological samples of different types of polyps from 23 patients was characterized using an open-ended coaxial probe between 0.5 and 20 GHz. The obtained measurements were classified into five tissue groups before applying a data reduction step with a frequency dispersive single-pole Debye model. The classification was finally compared with pathological analysis of tissue samples, which is the gold standard. Results: The complex permittivity progressively increases as the tissue degenerates from normal to cancer. When comparing to the gold-standard histological tissue analysis, the sensitivity and specificity of the proposed method is the following: 100% and 95% for cancer diagnosis; 91% and 62% for adenomas with high-grade dysplasia; 100% and 61% for adenomas with low-grade dysplasia; and 100% and 74% for hyperplastic polyps, respectively. In addition, complex permittivity measurements were independent of the lesion shape and size, which is also an interesting property comparing to current colonoscopy techniques. Conclusions: The contrast in complex permittivities between normal and abnormal colon tissues presented here for the first time demonstrate the potential of these measurements for tissue classification. It also opens the door to the development of a microwave endoscopic device to complement the outcomes of colonoscopy with functional tissue information., This work was supported by the Department of Universitats, Recerca i Societat de la Informacio of the Catalan Government through Llavor 2014LLAV00016 and producte 2016PROD00068 projects, La Caixa through Caixaimpulse program CI16-00058, the Spanish Comision Interministerial de Ciencia y Tecnologıa (CICYT) under projects TEC2016- 78028-C3-1-P, TEC2014-58582-R, the Spanish Agencia Estatal de Investigacion Unidad de Excelencia Maria de Maeztu (MDM-2016-0600), the Spanish Ministerio de Economıa, Industria y Competitividad, DTS17/00090 and CERCA Programme/Generalitat de Catalunya.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Contribución de congreso (ConferenceOutput)

Smart Beam Management for Vehicular Networks Using ML

  • Bharath-Reddy, G.
  • Montero, L.
  • Perez-Romero, J.
  • Molins-Benlliure, Jaime
  • Molina, J.
  • Romeu, J.
  • Jofre-R., L.
  • Ferrando Bataller, Miguel|||0000-0003-3561-5112
[EN] The mmWave frequencies will be widely used in future vehicular communications. At these frequencies, the radio channel becomes much more vulnerable to slight changes in the environment like motions of the device, reflections or blockage. In high mobility vehicular communications the rapidly changing vehicle environments and the large overheads due to frequent beam training are the critical disadvantages in developing these systems at mmWave frequencies. Hence, smart beam management procedures are desired to establish and maintain the radio channels. In this paper, we propose that using the positions and respective velocities of the vehicles in the dynamic selection of the beam pair, and then adapting to the changing environments using ML algorithms, can improve both network performance and communication stability in high mobility vehicular communications., This work was supported by the Spanish Comision Interministerial de Ciencia y Tecnologia (CICYT) under projects TEC2016-78028-C3-1-P and MDM2016-O6OO, Catalan Research Group 2017 SGR 21, and Industrial Doctorate programme (2018-DI-084) of Generalitat de Catalunya.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Contribución de congreso (ConferenceOutput)

Vehicular mm-Wave Array for Smart Handover

  • Bharath Reddy, G.
  • Ramirez, G. A.
  • Molins-Benlliure, Jaime
  • Romeu, J.
  • Jofre-R., L.
  • Ferrando Bataller, Miguel|||0000-0003-3561-5112
[EN] The emergence of new technologies such as autonomous vehicles and high data rate 5G networks requires advanced antenna types that are capable of fulfilling requirements for highly demanding wireless communication links. The array of microstrip-fed slot-coupled patches is one such type of antenna that provides low return loss and good transient behaviour for broadband applications. A compact size slot-coupled patch antenna subarray and its phased array is proposed in this paper. Two different substrates Rogers TMM4 and Green TapeTM 951 Low Temperature Co-Fired Ceramic (LTCC) are considered for the fabrication of microstrip feedline. The feedline is fabricated on the respective substrates and then mounted on a Rogers RT/duroid 5880 laminate. Ground planes are used on both the front and backside of the antenna array. The antenna is operating in a range of 24.25 GHz - 29.5 GHz. A Smart Array is proposed in this paper which has a good performance in terms of antenna gain and scanning property for 5G application in Smart handovers., This work was partly funded by the Ministerio de Ciencia e Innovacion (MICINN) under projects TEC2016-78028-C3-1- P, PID 2019-107885GB-C31, MDM2016-0600, and Catalan Research Group 2017 SGR 219.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Assessment of LTCC-Based Dielectric Flat Lens Antennas and Switched-Beam Arrays for Future 5G Millimeter-Wave Communication Systems

  • Imbert, Marc
  • Romeu, Jordi
  • Martinez-Ingles, Maria-Teresa
  • Molina-García-Pardo, José María
  • Jofre, Lluis
  • Baquero Escudero, Mariano|||0000-0001-8772-5431
[EN] This paper presents the design, low-temperature co-fired ceramics (LTCC) fabrication, and full experimental verification of novel dielectric flat lens antennas for future high data rate 5G wireless communication systems in the 60 GHz band. We introduce and practically completely evaluate and compare the performance of three different inhomogeneous gradient-index dielectric lenses with the effective parameters circularly and cylindrically distributed. These lenses, despite their planar profile antenna configuration, allow full 2-D beam scanning of high-gain radiation beams. A time-domain spectroscopy system is used to practically evaluate the permittivity profile achieved with the LTCC manufacturing process, obtaining very good results to confirm the viability of fabricating inhomogeneous flat lenses in a mass production technology. Then, the lenses performance is evaluated in terms of radiation pattern parameters, maximum gain, beam scanning, bandwidth performance, efficiencies, and impedance matching in the whole frequency band of interest. Finally, the performance of the three lenses is also experimentally evaluated and compared to a single omni-directional antenna and to a ten-element uniform linear array of omni-directional antennas in real 60 GHz wireless personal area network indoor line-of-sight (LOS) and obstructed-LOS environments, obtaining interesting and promising remarkable results in terms of measured received power and root-mean-square delay spread. At the end of this paper, an innovative switched-beam antenna array concept based on the presented cylindrically distributed effective parameters lens is also introduced and completely evaluated, confirming the potential applicability of the proposed antenna solution for future 5G wireless millimeter-wave communication system., This work was supported in part by the Spanish Inter-Ministerial Commission on Science and Technology (CICYT) under Projects TEC2013-47360-C3-1-P, TEC2013-47360-C3-2-P, and TEC2016-78028-C3-1-P, by FEDER and the Unidad de Excelencia Maria de Maeztu MDM-2016-0600, which is financed by the Agenda Estatal de Investigacion, Spain, and by the "Ministerio de Economia" through the FPI fellowship program.
Repositorio Digital UPCT
Publicación Artículo científico (JournalArticle)

Terahertz frequency-scaled differential imaging for Sub-6 GHz vehicular antenna signature analysis

  • Solano Pérez, José Antonio
  • Martínez Inglés, María Teresa
  • Molina García-Pardo, José María
  • Romeu Robert, Jordi
  • Jofre Roca, Lluís
  • Ballesteros Sánchez, Christian
  • Rodríguez Rodríguez, José Víctor
  • Mateo Aroca, Antonio
The next generation of connected and autonomous vehicles will be equipped with high numbers of antennas operating in a wide frequency range for communications and environment sensing. The study of 3D spatial angular responses and the radiation patterns modified by vehicular structure will allow for better integration of the associated communication and sensing antennas. The use of near-field monostatic focusing, applied with frequency-dimension scale translation and differential imaging, offers a novel imaging application. The objective of this paper is to theoretically and experimentally study the method of obtaining currents produced by an antenna radiating on top of a vehicular platform using differential imaging. The experimental part of the study focuses on measuring a scaled target using an imaging system operating in a terahertz band—from 220 to 330 GHz—that matches a 5G frequency band according to frequency-dimension scale translation. The results show that the induced currents are properly estimated using this methodology, and that the influence of the bandwidth is assessed., This research was funded by the Ministry of Education and Science, Spain (PID2019-107885GB-C33/AEI/10.13039/501100011033, TEC2016-78028-C3-1-P, TEC2016-78028-C3-2-P and TEC2016-78028-C3-3-P, MDM2016-O6OO), Catalan Research Group 2017 SGR 219, and the European FEDER funds.
Repositorio Digital UPCT
Publicación Artículo científico (JournalArticle)

Linear and circular UWB millimeter-wave and terahertz monostatic near-field synthetic aperture Iimaging

  • Solano Pérez, José Antonio
  • Martínez Inglés, María Teresa
  • Molina García-Pardo, José María
  • Romeu Robert, Jordi
  • Jofre Roca, Lluís
  • Rodríguez Rodríguez, José Víctor
  • Mateo Aroca, Antonio
Millimeter-wave and terahertz frequencies offer unique characteristics to simultaneously obtain good spatial resolution and penetrability. In this paper, a robust near-field monostatic ocusing technique is presented and successfully applied for the internal imaging of different penetrable geometries. These geometries and environments are related to the growing need to furnish new vehicles with radar-sensing devices that can visualize their surroundings in a clear and robust way. Sub-millimeter-wave radar sensing offers enhanced capabilities in providing information with a high level of accuracy and quality, even under adverse weather conditions. The aim of this paper was to research the capability of this radar system for imaging purposes from an analytical and experimental point of view. Two sets of measurements, using reference targets, were performed in the W band at 100 GHz (75 to 110 GHz) and terahertz band at 300 GHz (220 to 330 GHz). The results show spatial resolutions of millimeters in both the range (longitudinal) and the cross-range (transversal) dimensions for the two different imaging geometries in terms of the location of the transmitter and receiver (frontal or lateral views). The imaging quality in terms of spatial accuracy and target material parameter was investigated and optimized., This research was funded by the Ministry of Education and Science, Spain (TEC2016-78028-C3-1-P and TEC2016-78028-C3-2-P) and by the European FEDER funds.
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

High-efficiency reconfigurable dual-band class-F power amplifier with harmonic control network using MEMS

  • Gilasgar, Mitra
  • Barlabe Dalmau, Antoni
  • Pradell i Cara, Lluís
©2020 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes, creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., This letter presents a novel reconfigurable, high-efficiency class-F power amplifier (PA) structure, using a commercial GaN-HEMT, that achieves dual-band configuration not only at the fundamental frequency but also at the harmonics. With a proper harmonic tuning structure, the need for an extra filtering section is eliminated, resulting in a high dual-band efficiency with a reduced number of components and size. The reconfigurable structure uses commercial singlepole-double-throw (SPDT) and single-pole-single-throw (SPST) MEMS switches optimally placed on the stubs to select between 900 and 1800 MHz. The reconfigurable PA achieves a measured power-added efficiency (PAE) of 69.5% and a power gain of 13.6 dB while delivering an output power of 39.1 dBm at 900 MHz. At 1800 MHz, the amplifier achieves a PAE of 57.9%, a power gain of 10.5 dB, and an output power of 38.5 dBm., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

A submillimeter wave parabolic reflector by additive manufacturing

  • Romeu Robert, Jordi
  • Aguasca Solé, Alberto
  • Blanch Boris, Sebastián
  • O'Callaghan Castellà, Juan Manuel
  • Jofre Roca, Lluís
  • Buitrago Ventura, Santiago
The manufacturing of prototype of an offset parabolic reflector to operate at 120 GHz is presented. The paper describes the different metallization options to achieve a good performance., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

On the accuracy of the adaptive cross aproximation algorithm

  • Heldring, Alexander
  • Úbeda Farré, Eduard
  • Sekulic, Ivan
  • Rius Casals, Juan Manuel
© 2017 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes,creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., This contribution identifies an often ignored source of uncertainty in the accuracy of the adaptive cross approximation algorithm, and proposes a combination of adaptations that reduce this uncertainty with negligible additional computational cost., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

A 2.4 GHz CMOS class-F power amplifier with reconfigurable load-impedance matching

  • Gilasgar, Mitra
  • Barlabe Dalmau, Antoni
  • Pradell i Cara, Lluís
© 2019 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes, creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., A novel reconfigurable CMOS class-F power amplifier (PA) at 2.4 GHz is proposed in this paper. It is able to match the output load variations mainly due to the effect of hand and head on a mobile phone. The effect of load variation on power-added efficiency (PAE), output power, and distortion is compensated by reconfiguring the output network using an impedance tuner. The tuner controls the output matching at fundamental frequency without affecting the class-F harmonic tuning up to 3rd harmonic. To the best of our knowledge, this is the first design of a CMOS class-F PA addressed to compensate the effect of load variation. Measurement results for 50 ohm load impedance show a maximum PAE of 26% and maximum output power of 19.2 dBm. The measured total harmonic distortion is 4.9%. Measurement results for load values other than 50 ohm show that PAE increases from 6.5% (not-tuned PA) up to 19.9% (tuned PA) with the same output power (19.2 dBm). Tuning also reduces the adjacent-channel leakage ratio by 5 dB and the spectral regrowth of a Wi-Fi signal at the PA output. The size of the fabricated chip is 1.6 mm × 1.6 mm., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Design of minimum nonlinear distortion reconfigurable antennas for next-generation communication systems

  • Ramírez Arroyave, Germán Augusto
  • Barlabe Dalmau, Antoni
  • Pradell i Cara, Lluís
  • Araque Araque, Javier Leonardo
  • Cetiner, Bedri Artug
  • Jofre Roca, Lluís
Nonlinear effects in the radio front-end can degrade communication quality and system performance. In this paper we present a new design technique for reconfigurable antennas that minimizes the nonlinear distortion and maximizes power efficiency through the minimization of the coupling between the internal switching ports and the external feeding ports. As a nonlinear design and validation instance, we present the nonlinear characterization up to 50 GHz of a PIN diode commonly used as a switch for reconfigurable devices in the microwave band. Nonlinear models are extracted through X-parameter measurements supported by accurate calibration and de-embedding procedures. Nonlinear switch models are validated by S-parameter measurements in the low power signal regime and by harmonic measurements in the large-signal regime and are further used to predict the measured nonlinearities of a reconfigurable antenna. These models have the desired particularity of being integrated straightforwardly in the internal multi-port method formulation, which is used and extended to account for the power induced on the switching elements. A new figure of merit for the design of reconfigurable antennas is introduced—the power margin, that is, the power difference between the fed port and the switching elements, which combined with the nonlinear load models directly translates into nonlinearities and power-efficiency-related metrics. Therefore, beyond traditional antenna aspects such as port match, gain, and beam orientation, switch power criteria are included in the design methodology. Guidelines for the design of reconfigurable antennas and parasitic layers of minimum nonlinearity are provided as well as the inherent trade-offs. A particular antenna design suitable for 5G communications in the 3.5 GHz band is presented according to these guidelines, in which the specific switching states for a set of target performance metrics are obtained via a balancing of the available figures of merit with multi-objective separation criteria, which enables good control of the various design trade-offs. Average Error Vector Magnitude (EVM) and power efficiency improvement of 12 and 6 dB, respectively, are obtained with the application of this design approach. In summary, this paper introduces a new framework for the nonlinear modeling and design of reconfigurable antennas and provides a set of general-purpose tools applicable in cases beyond those used as examples and validation in this work. Additionally, the use of these models and guidelines is presented, demonstrating one of the most appealing advantages of the reconfigurable parasitic layer approach, their low nonlinearity, This research was supported by the Spanish “Comision Interministerial de Ciencia y Tecnologia” (CICYT) under projects TEC2013-47360-C3-1-P/AEI/10.13039/501100011033, TEC2016- 78028-C3-1-P/AEI/10.13039/501100011033, and MDM2016-O6OO, and Catalan Research Group 2017 SGR 219, and by the Colombian “Departamento Administrativo de Ciencia, Tecnología e Innovación” (Colciencias) through convocatoria 727 de 2015, Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Acceleration of Born series by change of variables

  • López Menchón, Héctor
  • Rius Casals, Juan Manuel
  • Heldring, Alexander
  • Úbeda Farré, Eduard
In this work, we propose a method to enhance the convergence of the Born series. The Born series is widely used in scattering theory, but its convergence is only guaranteed under certain restrictive conditions which limit the cases where this formulation can be applied. The proposed method, based on modifying the singularities of the resolvent operator by a change of variables, accelerates the convergence of the series or even achieves convergence in otherwise divergent cases. Due to its low computational cost and ease of implementation, the method preserves the advantages of the Born series while it extends its range of application. It can also be applied to a variety of methods relying on the same mathematical principles as the Born series. Numerical examples are provided to show that a significant improvement can be achieved with simple techniques and with a limited knowledge about the operator spectrum., This work was partly funded by the Ministerio de Ciencia e Innovacion (MICINN) under projects TEC2016-78028-C3-1-P, MDM2016-0600, TEC2017-83343-C4-2-R, TEC2017-84817-C2-2-R, PID 2019-107885GB-C31 and Catalan Research Group 2017 SGR 219; and by Secretary of Universities and Research of the Ministry of Business and Knowledge of the Generalitat of Catalonia and European Social Fund under scholarship 2019 FI B00788., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

A simple and effective microwave invisibility cloak based on frequency selective surfaces

  • Yuste, Pedro
  • Rius Casals, Juan Manuel
  • Romeu Robert, Jordi
  • Blanch Boris, Sebastián
  • Heldring, Alexander
  • Úbeda Farré, Eduard
This paper presents the design, simulation, manufacturing and testing of a simple invisibility cloak based on a frequency selective surface (FSS). The work is focused on cloaking an electrically thin dielectric cylinder with an easy to manufacture FSS made of copper strips glued to the cylinder surface. In contrast to many papers in the literature, the full procedure from formulation to measurement results is presented here. An original approach to obtain the effective surface impedance of the cylindrical FSS from either simulated or measured far fields is introduced. The measurement results show excellent and relatively wide band performance of the cloak prototype., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Linear and Circular UWB Millimeter-Wave and Terahertz Monostatic Near-Field Synthetic Aperture Imaging

  • solano perez, jose antonio
  • Martinez-Ingles, Maria-Teresa
  • Molina-Garcia Pardo, Jose Maria
  • Romeu Robert, Jordi
  • Jofre Roca, Lluís
  • Rodríguez, José Victor
  • Mateo-Aroca, Antonio
Millimeter-wave and terahertz frequencies offer unique characteristics to simultaneously obtain good spatial resolution and penetrability. In this paper, a robust near-field monostatic focusing technique is presented and successfully applied for the internal imaging of different penetrable geometries. These geometries and environments are related to the growing need to furnish new vehicles with radar-sensing devices that can visualize their surroundings in a clear and robust way. Sub-millimeter-wave radar sensing offers enhanced capabilities in providing information with a high level of accuracy and quality, even under adverse weather conditions. The aim of this paper was to research the capability of this radar system for imaging purposes from an analytical and experimental point of view. Two sets of measurements, using reference targets, were performed in the W band at 100 GHz (75 to 110 GHz) and terahertz band at 300 GHz (220 to 330 GHz). The results show spatial resolutions of millimeters in both the range (longitudinal) and the cross-range (transversal) dimensions for the two different imaging geometries in terms of the location of the transmitter and receiver (frontal or lateral views). The imaging quality in terms of spatial accuracy and target material parameter was investigated and optimized., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Frequency extrapolation of IE-MEI linear system Coefficients in 2D

  • Rius Casals, Juan Manuel
  • Heldring, Alexander
  • Úbeda Farré, Eduard
The Integral Equation MEI (IE-MEI) method for the sparsification of Method of Moments linear system matrix is revisited here. It achieves cpu computation time and storage memory requirements of order O(N ) (for 2D perfectly conducting scatterers of arbitrary convex shape), which is –to our knowledge– the best asymptotic computational complexity ever achieved by integral equation methods. The aim of this paper is to present yet unpublished details of the algorithm to extrapolate the linear system coefficients and the latest results obtained using modern computers., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

A 125-143-GHz frequency-reconfigurable BiCMOS compact LNA using a single RF-MEMS switch

  • Heredia, Julio
  • Ribó i Pal, Miquel
  • Pradell i Cara, Lluís
  • Wipf, Selin Tolunay
  • Göritz, Alexander
  • Wipf, Christian
  • Kaynak, Mehmet
© 2019 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes,creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., In this letter, a 125-143-GHz frequency-reconfigurable BiCMOS compact low-noise amplifier (LNA) is presented for the first time. It consists of two cascode stages and was fabricated using a 0.13-µm SiGe:C BiCMOS process, which integrates RF-MEMS switches. A systematic general design procedure to obtain a balanced gain and noise figure in both frequency states is proposed. The LNA size is minimized by using only one RF-MEMS switch to select the frequency band and a multimodal three-line microstrip structure in the input matching network. The measured gain and noise figure are 18.2/16.1 and 7/7.7 dB at 125/143 GHz. The power consumption is 36.8 mW. The measured results are in good agreement with simulations., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Millimeter-wave MIMO array measurement system for imaging and channel characterization

  • Ballesteros Sánchez, Christian
  • Montero Bayo, Luca
  • Ramírez Arroyave, Germán Augusto
  • Dagatti, Mayco
  • Solano Pérez, José Antonio
  • Molina García-Pardo, José María
  • Romeu Robert, Jordi
  • Jofre Roca, Lluís
Millimeter-wave band offer unique characteristicsto obtain good spatial position and resolution of certain type oftargets. The aim of this paper is to study a near-field focusingtechnique applied to the imaging of different geometries, from ananalytical, numerical and experimental point of view. Millimeter-wave band scattering simulations are performed and comparedwith imaging reconstruction of experimental measurements,using a particular set-up and scenario. This work is a first stepto contribute to the growing need of sensing the environment andsurrounding objects of moving devices, such as new generationvehicles, in a clear and robust way with respect to other formsof sensing., This work was supported by the Spanish Ministry of Education and Science under projects 2019-107885GB-C31,TEC2016-78028-C3-1-P, TEC2016-78028-C3-2-P, TEC2016-78028-C3-3-P, MDM2016-0600, the Catalan Research Group 2017 SGR 219 and by the European FEDER funds. The Spanish Ministry of Education contributes via apredoctoral grant to the first author (FPU17/05561)., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Beam management for vehicle-to-vehicle (V2V) communications in millimeter wave 5G

  • Montero Bayo, Luca
  • Ballesteros Sánchez, Christian
  • De Marco, Cesar
  • Jofre Roca, Lluís
Cooperative, Connected and Automated Mobility (CCAM) is expected to leverage the full potential of wireless communications. With the growing adoption of 5G and its support for Vehicle-to-Everything (V2X) communications, beamformed vehicular communications at millimeter-wave (mmWave) bands are expected to enable the most demanding connected driving applications. Beamformed V2X links present the challenge of beam management in such a fast-changing scenario. This paper goes through the practical limitations of the 5G V2X stack to support successful beamforming procedures. Two beam management strategies are proposed. Both strategies are evaluated in terms of power performance, beam recovery time and channel usage. The results suggest that significant differences apply when the beam is more frequently updated, whereas little improvement is seen by increasing the size of the beamset. Also, the selection of a proper strategy is shown to be important to alleviate the channel from overheads, and substantial differences in required signaling can be seen depending on the beam-tracking approach., This work was partly funded by the Spanish Comisión Interministerial de Ciencia y Tecnología under projects TEC2013-47360- C3-1-P, TEC2016-78028-C3-1-P and MDM2016-0600, and Catalan Research Group 2017 SGR 219. The Spanish Ministry of Education (FPU17/05561) and Generalitat de Catalunya DI programme (2018- DI-084) also contribute with predoctoral grants for the authors., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Optical beam steering network with multiband capability

  • Vega, Sara
  • Nuño Gómez, Daniel-Juan
  • Santos Blanco, M. Concepción
A multiwavelength (MW) optical true time delay Network (OTTDN) to feed a phased array antenna (PAA) is presented. Beam steering capabilities can be demonstrated when applying MW tuning. A Dual Electrode Mach Zehnder Modulator (DE-MZM) as radio frequency (RF) external modulating stage allows to tune the operative band avoiding severe Chromatic Dispersion (CD) fading to obtain a flattened response. A working example simulation of a 4 elements array at 8 GHz shows the RF multiband spectral flat response potential of the technique, as well as the network conditions needed for beam steering with free-lobe operation., This work was partly funded by the Ministerio de Ciencia e Innovacion (MICINN) under projects TEC2016-78028-C3-1- P, PID 2019-107885GB-C31, MDM2016-0600, and Catalan Research Group 2017 SGR 219., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

High impedance monopole antenna for indoor terahertz communication system

  • Yazgan, Ayhan
  • Romeu Robert, Jordi
  • Jofre Roca, Lluís
In this study, a wideband terahertz antenna for indoor wireless communication systems is proposed. Antenna has high input impedance which is reasonable for terahertz systems due to the high output impedance of terahertz sources. Proposed antenna has been designed to operate in 0.67 THz which is one of the appropriate frequencies considering the atmospheric attenuation conditions for short range indoor terahertz wireless communication systems. Designed antenna has 0.8 kohm input impedance at the center of the band and approximately 100 GHz -10 dB bandwidth at 0.67 THz., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Reconfigurable dual-polarized beam-steering broadband antenna using a crossed-strips geometry

  • Ramírez Arroyave, Germán Augusto
  • Zhou, Ivan
  • Blanch Boris, Sebastián
  • Towfiq, Asaduzzaman
  • Cetiner, Bedri Artug
  • Romeu Robert, Jordi
  • Jofre Roca, Lluís
In this letter, a reconfigurable dual-polarized broadband antenna with beam-steering capabilities using a parasitic layer is proposed for 5G new radio (NR) frequency range 1 (FR-1) applications. The antenna is a dual-port aperture-stacked patch structure with symmetrical orthogonal (horizontal and vertical) currents. The beam-steering is achieved by a pair of reconfigurable cross-shaped parasitic strips, which bestow the antenna three main beam directions θ = { ~ -25 ° ,0 ° , ~ 25 ° }, Ψ = {0 ° } with pointing and gain (7 dB) stability across a 30% impedance bandwidth (S 11 , S 22 <; -10 dB) from 3.2 - 4.3 GHz for both ports/polarizations. A prototype of the antenna is manufactured and measured demonstrating results in accordance with simulation expectations., This work was supported in part by Colombian “Departamento Administrativo de Ciencia, Tecnología e Innovación” Colciencias through convocatoria 727 of 2015 scholarship, and in part by the Spanish “Comision Interministerial de Ciencia y Tecnologia” (CICYT) under Projects TEC2013-47360-C3-1-P/AEI/10.13039/501100011033, TEC2016-78028-C3- 1-P/AEI/10.13039/501100011033, and MDM2016-0600, and Catalan Research Group 2017 SGR 219., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

GRECO: 30 years of graphical processing techniques for RCS computation

  • Rius Casals, Juan Manuel
  • Úbeda Farré, Eduard
  • Heldring, Alexander
This contribution to the special session in honor of Prof. Rafael Gómez-Martín will address the 30 year development of graphical processing techniques (GRECO) for fast computation of Radar Cross Section (RCS) of electrically large and complex targets. The development of GRECO started in 1988, in the frame of the “Applied research project for the development and validation of numerical methods for RCS prediction, analysis and optimization”, in which I had the pleasure to know Rafael since our groups where participating together in the project. The development of GRECO never stopped, and recently it has been updated by replacing the graphical processing technique for computation of surface reflection and edge diffraction by a hybrid CPU-graphical processing approach. The resulting code has the same accuracy as conventional RCS computation techniques, but detection of shadowed surfaces and edges is one order of magnitude faster than the most efficient O(N logN) implementations., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

3-D printed UWB microwave bodyscope for biomedical measurements

  • Rashid, Saba
  • Jofre Roca, Lluís
  • Garrido, Alejandra
  • González, Giselle
  • Ding, Yongsheng
  • Aguasca Solé, Alberto
  • O'Callaghan Castellà, Juan Manuel
  • Romeu Robert, Jordi
© 2019 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes,creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., In this letter, a three-dimensional (3-D) printed compact ultrawideband (UWB) extended gap ridge horn (EGRH) antenna designed to be used for biological measurements of the human body is described. The operational frequency covers the microwave band of interest from 0.5 to 3.0 GHz (for an S 11 under -7 dB). The 3-D printed EGRH antenna is dielectrically matched to the permittivity of the human body, and because of its compactness, it can be visualized as a general-purpose microwave probe among the RF biomedical community. The probe has proven its capability as a pass-through propagation sensor for different parts of the human body and as a sensor detecting a 1 cm diameter object placed inside an artificial head phantom., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Accurate, grid-robust and versatile combined-field discretization for the electromagnetic scattering analysis of perfectly conducting targets

  • Úbeda Farré, Eduard
  • Sekulic, Ivan
  • Rius Casals, Juan Manuel
  • Heldring, Alexander
Recent implementations of the Electric-Field Integral Equation (EFIE) for the electromagnetic scattering analysis of perfectly conducting targets rely on the electric current expansion with the monopolar-RWG basis functions, discontinuous across mesh edges, and the field testing over volumetric subdomains attached to the surface boundary triangulation. As compared to the standard RWG-based EFIE-approaches, normally continuous across edges, these schemes exhibit enhanced versatility, allowing the analysis of geometrically non-conformal meshes, and improved accuracy, especially for subwavelength sharp-edged conductors. In this paper, we present a monopolar-RWG discretization by the Method of Moments (MoM) of the Combined-Field Integral Equation (CFIE) resulting from the addition of a volumetrically tested discretization of the EFIE and the Galerkin tested MFIE-implementation. We show for sharp-edged conductors the degree of improved accuracy in the computed RCS and the convergence properties in the iterative search of the solution. More importantly, as we show in the paper, these implementations become in practice advantageous because of their robustness to flaws in the grid generation or their agility in handling complex meshes arising from the interconnection of independently meshed domains. The hybrid RWG/monopolar-RWG discretization of the CFIE defines the RWG discretization over geometrically conformal and smoothly varying mesh regions and inserts the monopolar-RWG expansion strictly at sharp edges, for improved accuracy purposes, or over boundary lines between partitioning mesh domains, for the sake of enhanced versatility. These hybrid schemes offer similar accuracy as their fully monopolar-RWG counterparts but with fewer unknowns and allow naturally non-conformal mesh transitions without inserting additional inter-domain continuity conditions or new artificial currents., This work was supported by FEDER and the Spanish Comisión Interministerial de Ciencia y Tecnologı́a (CICYT) under projects TEC2016-78028-C3-1- P, TEC2017-84817-C2-2- R, and the Unidad de Excelencia Maria de Maeztu MDM-2016-0600, funded by the Agencia Estatal de Investigación, Spain., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Antenna packaging for in-body applications

  • Romeu Robert, Jordi
  • González López, Giselle
  • Blanch Boris, Sebastián
  • Jofre Roca, Lluís
A cylindrical mode expansion of the fields produced by an embedded antenna is used to determine the dimensions of the antenna packaging in order to minimize antenna impedance changes when the antenna is immersed in a varying dielectric medium., This work was supported by the Spanish “Comision Interministerial de Ciencia y Tecnologia” (CICYT) under projects TEC2016-78028-C3-1P, MDM2016-O6OO, and Catalan Research Group 2017 SGR 219., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Imaging system for automotive radome characterization

  • Buitrago Ventura, Santiago
  • Blanch Boris, Sebastián
  • Romeu Robert, Jordi
In this paper, a setup to obtain an image of the attenuation and the reflectivity of an automotive radome in the 77 GHz band is presented.The characterization of the reflectivity is becoming an important issue to be considered in an automotive radome design because the important effects it can produce in the radar sensor performance such as a false detection of a target or even a blindness of the radar sensor. In addition, the characterization of the attenuation is also important because the reduction in safety due to a possible non-detection of a target.For that reason, a setup to obtain an image of the attenuation and the reflectivity of a radome at the same time is presented. This system can be used to test prototypes in the design process or in the verification of manufactured samples., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Three-Dimensional beamsteering low complexity reconfigurable multilevel antenna

  • Zhou, Ivan
  • Ramírez Arroyave, Germán Augusto
  • Montero Bayo, Luca
  • Blanch Boris, Sebastián
  • Romeu Robert, Jordi
  • Jofre Roca, Lluís
© 2020 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes,creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., A low-complexity reconfigurable antenna (RA) capable of steering its beam into nine different directions corresponding to ¿={-42°,0°,42°} in the ¿={25°,0°,155°} planes, and ¿=±25° in the ¿=90° plane, using a reduced number of switches is presented. The RA operating at 3.4-3.8 GHz consists of a central dipole element excited by a coaxial probe, surrounded by four switchable parasitic dipoles located at different height levels above a ground plane, which acts as either a reflector for the elements located at an upper layer or a director for the ones at a lower layer, improving the radiation characteristics of the antenna. Each parasitic dipole is fed with a p-i-n diode as a switch, which enables the activation of these elements providing the desired modes of operation. The presented RA was manufactured and measured showing results with a good agreement with the theoretical and numerical simulation., This work was supported by the Spanish “ComisionInterministerial de Ciencia y Tecnologia” (CICYT) un-der projects TEC2013-47360-C3-1-P, TEC2016-78028-C3-1-P and MDM2016-0600, and Catalan Research Group 2017SGR 219, Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

In-cabin 120 GHz radar system for functional human breathing monitoring in a 3D scenario

  • López Montero, María José
  • Aguasca Solé, Alberto
  • Romeu Robert, Jordi
  • Jofre Roca, Lluís
Driving is one of the activities that takes a significant part of a person’s time, that is why monitoring vital signs is useful for the wellness of the occupants of the vehicle. One of the vital signs that provides more information about the state of the person, is the functional breathing. Compared to other vital signs indicators, breathing is more sensitive to cardiovascular events, emotional stress, physical exertion, or fatigue induced by long time driving, seen as variations in chest and abdomen elongation modes. Functional monitoring is a tool that can transcend, from measurement and detection to emotional changes through feedback of sounds, images, or videos to the driver. In this regard, this work proposes an imaging radar system to generate a topographic map with elongation modes of the driver’s chest and abdomen, at 120 GHz. Numerical simulations have been deployed in order to reconstruct the image from the receiver signal in the radar using spatial convolution. Furthermore, a metronome has been used to calibrate the radar for elongations measuring with respect to time, and finally, the system has been tested experimentally in an adult person, to generate a preliminary topographic map that allows matching the chest elongation modes to breathing patterns., This work was supported by the Spanish “Comision Interministerial de Ciencia y Tecnologia” (CICYT) under projects TEC2016-78028-C3-1-P and MDM2016-O6OO; Catalan Research Group 2017 SGR 219; and ”Secretaría Nacional de Educación Superior, Ciencia, Tecnología e Innovación” (SENESCYT) from the Ecuadorian government., Peer Reviewed, Objectius de Desenvolupament Sostenible::3 - Salut i Benestar, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Characterization of THz radiation by collimated wavefront aperture raster scanning

  • Nuño Gómez, Daniel-Juan
  • Santos Blanco, M. Concepción
  • Gomez Diaz, J. Sebastian
  • Romeu Robert, Jordi
  • Jofre Roca, Lluís
We present measurements for characterization of the beam profile and polarization pattern of lens-coupled photoconductive antennas (PCAs) at THz frequencies using a setup with antennas at fixed positions and a movable aperture placed in between collimating THz lenses. The measured beam patterns for co-polar and cross-polar components reveal the expected Airy disc and quadrupole behavior, respectively. The temporal evolution of the polarization in the directions of maximum cross-polar component follows a single-cycle circle with opposite handedness at each side of the antennas line-of-sight (LOS). Results are consistent with those obtained with fiber-coupled movable antennas, while enjoying the simplicity of a free-space laser-PCA feed which does not require painstaking laser realignment for each beam direction measure., This work was partly funded by the Ministerio de Economía y Competitividad under projects TEC2016-78028-C3-1-P, PID 2019-107885GB-C31 and MDM2016-0600, and Catalan Research Group 2017 SGR 219., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Enhanced discretization of surface integral equations for resonant scattering analysis of sharp-edged plasmonic nanoparticles

  • Sekulic, Ivan
  • Tzarouchis, Dimitrios C.
  • Ylä-Oijala, Pasi
  • Úbeda Farré, Eduard
  • Rius Casals, Juan Manuel
The surface integral equation (SIE) method, discretized with the method of moments, is a well-established methodology for the scattering analysis of subwavelength plasmonic nanoparticles. SIEs are usually discretized with low-order basis functions that preserve the normal continuity of the surface currents across the edges arising in the meshed boundary, such as Rao-Wilton-Glisson (RWG) functions. However, the plasmonic enhancement modeling on sharp-edged particles is an extremely challenging task, especially due to the singular fields exerted at sharp corners, exposing a slow (or no) convergence in the computation of the scattering and absorption spectra. In this paper, we propose an alternative discretization strategy based on a discontinuous basis function set in conjunction with a volumetric-tetrahedral testing scheme. We demonstrate the potential of the proposed discretization scheme by studying scattering and absorption spectra of three canonical plasmonic polyhedra, i.e., a hexahedral, an octahedral, and a tetrahedral silver inclusion. The results expose an improved accuracy and faster convergence in both far-field and near-field regions when compared to the standard RWG implementation. The proposed discretization scheme can offer faster and more accurate routes towards the exploration and design of the plasmonic resonant spectrum of sharp-edged nanoparticles and nanoantennas., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Collimated beam FMCW radar for vital sign patient monitoring

  • Prat, Arnau
  • Blanch Boris, Sebastián
  • Aguasca Solé, Alberto
  • Romeu Robert, Jordi
  • Broquetas Ibars, Antoni
© 2018 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes,creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., Patient monitoring of vital signals such as breathing rhythm and heart beat rate can be done remotely by the use of a radar system. This approach is advantageous since it does not require any contact with the patient. Obviously contactless monitoring results in a more comfortable situation for the patient, and in occasions it is almost mandatory as in the case of heavy burnt or newborn patients. Moreover, additional information such movement patterns are also available. A 120 GHz FMCW radar is described with special focus on the design, construction and testing of a specific reflector antenna for the system. The system is based on a commercial radar chipset that includes its own antennas. The challenge has been to design the optimum reflector and to build it and test it in a cost effective way. The reflector has been 3D printed and a near-field testing technique has been implemented to assess its performance. The results show that the system is able to measure the vital signs at distances beyond one meter., Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Efficient analysis of thick curved metal sheets

  • Úbeda Farré, Eduard
  • Rius Casals, Juan Manuel
The scattering analysis of perfectly conducting plates with the method-of-moment discretization of the Electric-Field Integral Equation has been traditionally carried out according to the thin-sheet approximation, which neglects the current contributions over the plate rims. The plate is then modelled as an open surface and handles a restricted number of unknowns as compared with the canonical modelling as a closed object. The thin-sheet approximation, although used in many practical applications, becomes inaccurate for thick enough plates or plates under plane wave incidence at grazing angles. Recently, a thick-plate approach has been presented to address the time-efficient and accurate scattering analysis of thick plates. This scheme exploits the symmetry properties of fields and currents thereby giving rise to two uncoupled problems with roughly half the number of unknowns of the original problem. In this paper, we extend this thick-plate scheme to the efficient scattering analysis of thick curved sheets., This work was supported by FEDER and the "Spanish Plan Estatal de Investigación Científica y Técnica y de Innovación", under projects: TEC2017-84817-C2-2-R/ AEI/10.13039/501100011033, TEC2016-78028-C3-1-P/AEI/10.13039/501100011033, PID2019-107885GB-C31/AEI/10.13039/501100011033 and the Unidad de Excelencia Maria de Maeztu MDM-2016-0600/AEI/10.13039/501100011033, which is financed by the Agencia Estatal de Investigación, Spain, and Catalan Research Group 2017 SGR 219., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Design and evaluation of an antenna applicator for a microwave colonoscopy system

  • Guardiola, Marta
  • Djafri, Kahina
  • Challal, Mouloud
  • González Ballester, Miguel A.
  • Fernández-Esparrach, Glòria
  • Camara, Oscar
  • Romeu Robert, Jordi
© 2019 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes,creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., This paper presents a design of a compact antenna applicator for a microwave colonoscopy system. Although colonoscopy is the most effective method for colorectal cancer detection, it suffers from important visualization restrictions that limit its performance. We recently reported that the contrast between healthy mucosa and cancer was 30%-100% for the relative permittivity and conductivity, respectively, at 8 GHz, and the complex permittivity increased proportionally to the degeneration rate of polyps (cancer precursors). The applicator is designed as a compact cylindrical array of eight antennas attached at the tip of a conventional colonoscope. The design presented here is a proof-of-concept applicator composed by one transmitting and one receiving cavity-backed U-shaped slot antenna elements fed by an L-shaped microstrip line. The antennas are low profile and present a high isolation at 8 GHz. The antenna performance is assessed with simulations and experimentally with a phantom composed by different liquids., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Comparative efficiency and power assessment of optical photoconductive material-based terahertz sources for wireless communication systems

  • Yazgan, Ayhan
  • Jofre Roca, Lluís
  • Romeu Robert, Jordi
Electronic version of an article published as [Journal of Circuits, Systems and Computers, vol. 28, num. 1, 2018] [https://doi.org/10.1142/S0218126619500051] © [copyright World Scientific Publishing Company] [https://www.worldscientific.com/worldscinet/jcsc], Terahertz band has recently attracted the attention of the communication society due to its huge bandwidth and very high-speed wireless communications capability. It has been utilized in a variety of disciplines including physics, biology and astronomy for years; and the main concerns have always been obtaining highly efficient and high-power terahertz sources. Today, these problems are still the most important issues in establishing an operable wireless terahertz communication link. In this paper, recent studies in the field of terahertz source design are investigated based on the terahertz output power and efficiency. Solid-state sources and optical sources were comparatively reviewed with optical photoconductive material (OPM)-based methods which are combined with the terahertz antennas in the design phase generally. For wireless communication, the most suitable frequencies are between 0.3THz and 1THz due to the attenuation profile of the atmosphere. For this reason, based on the recently published studies, it has been observed that OPM and resonant tunneling diode-based sources are the most promising terahertz sources in terms of efficiency and power. Key issues and the main problems of terahertz photoconductive antennas which are the base of OPM method were also discussed in this paper., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Improving the accuracy of the adaptive cross approximation with a convergence criterion based on random sampling

  • Heldring, Alexander
  • Úbeda Farré, Eduard
  • Rius Casals, Juan Manuel
The accuracy of the Adaptive Cross Approximation (ACA) algorithm, a popular method for the compression of low rank matrix blocks in Method of Moment computations, is sometimes seriously compromised by unpredictable errors in the convergence criterion. This paper proposes an alternative criterion, based on global sampling of the error in the elements of the ACA compressed matrix. The sampling error depends on the size of the sample but also on the population distribution of the error, which makes it difficult to control the error independently of the underlying problem. However, as argued and demonstrated in the paper, the distribution of the error converges to the same unique probability distribution function for all low rank matrices. Complementing the sampling criterion with a simple mechanism to detect this convergence, we arrive at a criterion that controls the error irrespective of the underlying problem. As a practical example the RCS of a moderate size metallic ogive is computed to illustrate the merits of the proposed criterion. The proposed algorithm may also be useful in other methods that approximate low-rank matrices by interpolation of a reduced set of its elements., This work was partly funded by the Ministerio de Ciencia e Innovacion (MICINN) under projects TEC2016-78028-C3-1-P, TEC2017-84817-C2-2-R, TEC2017-83343-C4-2-R, PID 2019-107885GBC31, MDM2016-0600, and Catalan Research Group 2017 SGR 219., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Edge diffraction computation using GRECO

  • Rius Casals, Juan Manuel
  • Carbo, Alex
  • Úbeda Farré, Eduard
  • Heldring, Alexander
This paper addresses two graphical processing approaches for computation of edge scattering with Physical Theory of Diffraction (PTD) high-frequency approximation. One is based on processing only a bitmap containing an image of the radar target, while the other uses a bitmap graphical processing algorithm to identify illuminated and shadowed facet mesh vertices, published in 2014, and then computes PTD diffraction coefficients for illuminated edges in the conventional way. The first approach is much faster for models containing a very large number of facets, but introduces pixel discretization noise, that can be alleviated by using larger bitmaps., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

The state of art of terahertz sources: a communication perspective at a glance

  • Yazgan, Ayhan
  • Jofre Roca, Lluís
  • Romeu Garbí, Jordi
Terahertz band lying between infrared and microwave is a very promising part of electromagnetic spectrum for spectroscopy, space applications and different kind of imaging applications such as medical and security. Recently, this special band has attracted the attention of communication society because of its huge bandwidth and therefore ability of very high speed wireless communications. One of the challenges still on the table is to obtain efficient terahertz sources. In this paper, recent studies on the topic of efficient terahertz sources are reviewed comparatively. Especially for the communication concept, taking into account the efficiency, it can be said that the trend goes to the optical photoconductive materials method including plasmonic electrodes., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Compact, wideband impedance tuner using a three-line-microstrip structure

  • Heredia Vega, Julio César
  • Ribó Pal, Miquel
  • Pradell i Cara, Lluís
© 2018 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes,creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., A novel three-line-microstrip compact impedance tuner is presented. It is based on a multimodal structure wherein six variable capacitances, implemented with two parallel-connected varactors each, create multiple interactions among the three-line-microstrip modes in a reduced circuit area. Experimental results show better-than-70% coverage of the Smith chart in an 85% frequency bandwidth from 1.4 to 3.2 GHz., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Optical phase effects in reconfigurable microwave photonic filters with multiple wavelength input

  • Nuño Gómez, Daniel-Juan
  • Santos Blanco, M. Concepción
Microwave photonic filters with a multiple wavelength input are analyzed. A comprehensive model assessing the impact of the phase characteristic of the optical stage is presented from which optimized design rules have been derived. Examples with one, 2 and 3 lasers are provided along with experimental results supporting our findings., This work was supported by the Spanish “Comision Interministerial de Ciencia y Tecnologia” (CICYT) under projects TEC2016-78028-C3-1-P, Maria de Maeztu MDM2016-O6OO, and FLIPER TEC2015-70835., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Variable capacitive antenna loading for embedded RFID sensors

  • Gonzalez, Giselle
  • Jofre Roca, Lluís
  • Romeu Robert, Jordi
  • Cairó Molins, Josep Ignasi
In this paper, a self-adaptive folded dipole antenna to work embedded in media with changing physical and chemical properties for RFID applications is proposed. Self-adaptability is provided by taking advantage of the dual-mode behaviour of the folded dipole antenna where variable capacitance diodes are strategically placed to compensate for the change produced in the electromagnetic properties of the embedding medium. The presented antenna has been optimized at 868MHz., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

3D-printed UHF-RFID tag for embedded applications

  • Vidal, Neus
  • Lopez-Villegas, Josep Maria
  • Romeu Robert, Jordi
  • Salas Barenys, Arnau
  • Garcia-Miquel, Aleix
  • González López, Giselle
  • Jofre Roca, Lluís
This paper presents the design, manufacture and characterization of a novel 3D passive UHF-RFID tag for embedded applications. The prototype is fabricated using additive manufacturing techniques: 3D printing and copper electroplating. The design, manufacturing process and measurement set-up are presented and discussed in detail. We propose a biconical antenna design with spiral strips embedded in the cones to provide compactness without breaking the symmetry of the component and to improve bandwidth. The antenna is matched to a commercial UHF-RFID integrated circuit. We incorporate a packaging design that consists of a dielectric coating, to provide proper operation in different media or surrounding environments with changing electromagnetic properties. The good agreement between experimental results and Finite Element Method simulations allows us to validate the whole process. Finally, a compact capsule-type RFID tag is proposed and its performance in different media is reported., This work was supported by the Spanish Ministry of Economy and Competitiveness, under Project TEC2017-83524-R, ProjectTEC2016-78028-C-1P, and Project MDM2016-0600, Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Terahertz frequency-scaled differential imaging for Sub-6 GHz vehicular antenna signature analysis

  • Solano-Sanchez, Jose-Antonio
  • Martinez-Ingles, Maria-Teresa
  • Molina García-Pardo, José María
  • Romeu Robert, Jordi
  • Jofre Roca, Lluís
  • Ballesteros Sánchez, Christian
  • Rodriguez, Jose-Victor
  • Mateo-Aroca, Antonio
The next generation of connected and autonomous vehicles will be equipped with high numbers of antennas operating in a wide frequency range for communications and environment sensing. The study of 3D spatial angular responses and the radiation patterns modified by vehicular structure will allow for better integration of the associated communication and sensing antennas. The use of near-field monostatic focusing, applied with frequency-dimension scale translation and differential imaging, offers a novel imaging application. The objective of this paper is to theoretically and experimentally study the method of obtaining currents produced by an antenna radiating on top of a vehicular platform using differential imaging. The experimental part of the study focuses on measuring a scaled target using an imaging system operating in a terahertz band—from 220 to 330 GHz—that matches a 5G frequency band according to frequency-dimension scale translation. The results show that the induced currents are properly estimated using this methodology, and that the influence of the bandwidth is assessed., This research was funded by the Ministry of Education and Science, Spain (PID2019-107885GB-C33/AEI/10.13039/501100011033, TEC2016-78028-C3-1-P, TEC2016-78028-C3-2-P and TEC2016-78028-C3-3-P, MDM2016-O6OO), Catalan Research Group 2017 SGR 219, and the European FEDER funds., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

A figure of merit to assess the performance of photoconductive antennas at terahertz band

  • Romeu Robert, Jordi
  • Cea Falcó, Marc de
  • Jofre Roca, Lluís
  • Yazgan, Ahmet Utku
Photoconductive antennas are one of the most efficient ways to radiate and receive EM waves around the 1 THz frequency band. The physical processes involved in photoconductive terahertz signal generation are complex enough to prevent having simple and accurate models to assess the performance of different electrode geometries. In this paper a figure of merit definition based on the physical processes involved in the electro-optical conversion process is proposed., Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Compact fully uniplanar bandstop filter based on slow-wave multimodal CPW resonators

  • Contreras Bleda, Adrián
  • Ribó i Pal, Miquel
  • Pradell i Cara, Lluís
  • Raynal, Víctor
  • Moreno, Ignacio
  • Combes, Maxence
  • Ten, Milena
© 2018 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes,creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., In this letter, a compact, fully uniplanar bandstop filter is presented. It is based on multimodal coplanar waveguide resonators implemented using a slow-wave periodic structure that greatly reduces the filter’s horizontal dimension. A multimodal circuit model for the filter is proposed and experimentally validated. A second-order filter prototype at 1.9 GHz, with a compact size of 0.31¿g×0.19¿g , was designed and fabricated. The filter features measured fractional bandwidths of 9.3% and 3.7% for -20- and -30-dB rejection levels, respectively, and a 1.3-dB insertion loss in the passband., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Dielectric properties of colon polyps, cancer, and normal mucosa: Ex vivo measurements from 0.5 to 20 GHz

  • Guardiola, Marta
  • Buitrago, Santiago
  • Fernández-Esparrach, Gloria
  • O’Callaghan, Joan M.
  • Romeu, Jordi
  • Cuatrecasas, Miriam
  • Córdova, Henry
  • González Ballester, Miguel Ángel, 1973-
  • Camara, Oscar
Purpose: Colorectal cancer is highly preventable by detecting and removing polyps, which are the precursors. Currently, the most accurate test is colonoscopy, but still misses 22% of polyps due to visualization limitations. In this paper, we preliminary assess the potential of microwave imaging and dielectric properties (e.g., complex permittivity) as a complementary method for detecting polyps and cancer tissue in the colon. The dielectric properties of biological tissues have been used in a wide variety of applications, including safety assessment of wireless technologies and design of medical diagnostic or therapeutic techniques (microwave imaging, hyperthermia, and ablation). The main purpose of this work is to measure the complex permittivity of different types of colon polyps, cancer, and normal mucosa in ex vivo human samples to study if the dielectric properties are appropriate for classification purposes. Methods: The complex permittivity of freshly excised healthy colon tissue, cancer, and histological samples of different types of polyps from 23 patients was characterized using an open-ended coaxial probe between 0.5 and 20 GHz. The obtained measurements were classified into five tissue groups before applying a data reduction step with a frequency dispersive single-pole Debye model. The classification was finally compared with pathological analysis of tissue samples, which is the gold standard. Results: The complex permittivity progressively increases as the tissue degenerates from normal to cancer. When comparing to the gold-standard histological tissue analysis, the sensitivity and specificity of the proposed method is the following: 100% and 95% for cancer diagnosis; 91% and 62% for adenomas with high-grade dysplasia; 100% and 61% for adenomas with low-grade dysplasia; and 100% and 74% for hyperplastic polyps, respectively. In addition, complex permittivity measurements were independent of the lesion shape and size, which is also an interesting property comparing to current colonoscopy techniques. Conclusions: The contrast in complex permittivities between normal and abnormal colon tissues presented here for the first time demonstrate the potential of these measurements for tissue classification. It also opens the door to the development of a microwave endoscopic device to complement the outcomes of colonoscopy with functional tissue information., This work was supported by the Department of Universitats, Recerca i Societat de la Informacio of the Catalan Government through Llavor 2014LLAV00016 and producte 2016PROD00068 projects, La Caixa through Caixaimpulse program CI16-00058, the Spanish Comision Interministerial de Ciencia y Tecnologıa (CICYT) under projects TEC2016- 78028-C3-1-P, TEC2014-58582-R, the Spanish Agencia Estatal de Investigacion Unidad de Excelencia Maria de Maeztu (MDM-2016-0600), the Spanish Ministerio de Economıa, Industria y Competitividad, DTS17/00090 and CERCA Programme/Generalitat de Catalunya.
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Assessment of 3-D printing technologies for millimeter-wave reflectors

  • Romeu Robert, Jordi
  • Blanch Boris, Sebastián
  • Vidal, Neus
  • Lopez-Villegas, Jose Maria
  • Aguasca Solé, Alberto
© 2018 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes,creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., Three different 3D printing technologies: Stereolithography (SLA), Fused Deposition Modeling (FDM) and HP Multi Jet Fusion Technology (MJF) are compared to build a parabolic reflector operating at 100 GHz. Fabrication tolerance and surface roughness before and after metallization are accurately measured. The performance of the reflectors is measured in the near field and its performance is compared against an optical grade reflector. In this way the performance of the final product is thoroughly assessed, Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Hybrid massive MIMO for urban V2I: Sub-6 GHz vs mmWave performance assessment

  • Pfadler, Andreas
  • Ballesteros Sánchez, Christian
  • Romeu Robert, Jordi
  • Jofre Roca, Lluís
© 2021 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes, creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works, The relevance of vehicle communications in next-generation networks entails the necessity of studying their performance in the framework of upcoming massive architectures. In this regard, a study of the wireless channel between a hybrid massive MIMO BS and a vehicular platform is proposed. Adequate metrics and methodology are provided for the assessment of such scenarios. The impact of different multi-antenna geometries and MIMO architectures in both vehicle and BS is modeled based on a numerical simulation of a realistic urban area. We compare several massive hybrid BS configurations with distinct multi-antenna vehicular rooftop solutions. This paper studies the channel eigenvalues and capacities for sub-6 GHz (3.6 GHz) and millimeter-wave (mmWave) (26 GHz) bands under different propagation conditions. The results suggest that the use of hybrid massive configurations increase the channel capacity by subdividing the massive BS into two or four logical radio channels. It is also shown that the greater available bandwidth at mmWave band can compensate the larger attenuation of radio channels in small size cells. The use of adequate metrics to measure the temporal coherence of the channel is also discussed for the beam switching update., This work wassupported in part by the Comisión Interministerial de Ciencia y Tecnología (CICYT) under projects TEC2016-78028-C3-1-P and MDM2016-0600, and in part by the Catalan Research Group 2017 SGR 219. The work of Christian Ballesteros was supported by the Spanish Ministry of Education under Grant FPU17/05561., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Nested fast adaptive cross approximation algorithm for solving electromagnetic scattering problems

  • Fang, Xiaoxing
  • Heldring, Alexander
  • Rius Casals, Juan Manuel
  • Chen, Xinlei
  • Cao, Qunsheng
In this paper, a Nested Fast Adaptive Cross Approximation (NFACA) algorithm is presented to accelerate the solution of electromagnetic scattering problems. It is based on the Fast Adaptive Cross Approximation (FACA) and the Nested Cross Approximation (NCA). In the NFACA, the FACA is applied instead of the ACA or the Chebyshev nodes, to enhance the efficiency. It is shown to have O(N) storage and computational complexity for electrically small problems. Different from the conventional NCA or the Fast Nested Cross Approximation (FNCA), the pivot-selection does not rely on a preliminary selection with Chebyshev nodes or ACA for each group. The NFACA permits the selection of the optimum pivots independently at each level to make the accuracy controllable. Numerical results of several objects are presented to demonstrate the performance of this method. Compared with the FACA and NCA in solving the electromagnetic scattering problems, the NFACA is more efficient both in computational cost and storage. Compared with the FNCA, the NFACA is both faster and more accurate., This work was supported in part by the National Nature Science Foundation of China under Grant 61871219, Grant 61771238, and Grant 61501227; in part by the Post-Graduate Research and Practice Innovation Program of Jiangsu Province under Grant KYCX18_0289; in part by the China Scholarship Council under Grant 201906830042; in part by the Spanish Ministerio de Ciencia e Innovacion (MICINN) under Project TEC2016-78028-C3-1-P, Project PID 2019-107885GB-C31, Project TEC2017-83343-C4-2-R, and Project MDM2016-0600; and in part by the Catalan Research Group 2017 SGR 219., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación

Design of minimum nonlinear distortion reconfigurable antennas for next-generation communication systems

  • Ramírez Arroyave, Germán Augusto
  • Barlabe Dalmau, Antoni
  • Pradell i Cara, Lluís
  • Araque Araque, Javier Leonardo
  • Cetiner, Bedri Artug
  • Jofre Roca, Lluís
Nonlinear effects in the radio front-end can degrade communication quality and system performance. In this paper we present a new design technique for reconfigurable antennas that minimizes the nonlinear distortion and maximizes power efficiency through the minimization of the coupling between the internal switching ports and the external feeding ports. As a nonlinear design and validation instance, we present the nonlinear characterization up to 50 GHz of a PIN diode commonly used as a switch for reconfigurable devices in the microwave band. Nonlinear models are extracted through X-parameter measurements supported by accurate calibration and de-embedding procedures. Nonlinear switch models are validated by S-parameter measurements in the low power signal regime and by harmonic measurements in the large-signal regime and are further used to predict the measured nonlinearities of a reconfigurable antenna. These models have the desired particularity of being integrated straightforwardly in the internal multi-port method formulation, which is used and extended to account for the power induced on the switching elements. A new figure of merit for the design of reconfigurable antennas is introduced—the power margin, that is, the power difference between the fed port and the switching elements, which combined with the nonlinear load models directly translates into nonlinearities and power-efficiency-related metrics. Therefore, beyond traditional antenna aspects such as port match, gain, and beam orientation, switch power criteria are included in the design methodology. Guidelines for the design of reconfigurable antennas and parasitic layers of minimum nonlinearity are provided as well as the inherent trade-offs. A particular antenna design suitable for 5G communications in the 3.5 GHz band is presented according to these guidelines, in which the specific switching states for a set of target performance metrics are obtained via a balancing of the available figures of merit with multi-objective separation criteria, which enables good control of the various design trade-offs. Average Error Vector Magnitude (EVM) and power efficiency improvement of 12 and 6 dB, respectively, are obtained with the application of this design approach. In summary, this paper introduces a new framework for the nonlinear modeling and design of reconfigurable antennas and provides a set of general-purpose tools applicable in cases beyond those used as examples and validation in this work. Additionally, the use of these models and guidelines is presented, demonstrating one of the most appealing advantages of the reconfigurable parasitic layer approach, their low nonlinearity., This research was supported by the Spanish “Comision Interministerial de Ciencia y Tecnologia” (CICYT) under projects TEC2013-47360-C3-1-P/AEI/10.13039/501100011033, TEC2016-78028-C3-1-P/AEI/10.13039/501100011033, and MDM2016-O6OO, and Catalan Research Group 2017 SGR 219, and by the Colombian “Departamento Administrativo de Ciencia, Tecnología e Innovación” (Colciencias) through convocatoria 727 de 2015, Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Study on beamforming V2I scenarios for sub-6 GHz and mmWave channels

  • Ballesteros Sánchez, Christian
  • Ramírez Arroyave, Germán Augusto
  • Montero Bayo, Luca
  • Romeu Robert, Jordi
  • Jofre Roca, Lluís
The study of the wireless channel between a hybrid massive MIMO Base Station (BS) and a vehicular platform is proposed. Several multi-antenna geometries and MIMO architectures in both vehicle and BS are numerically modeled and compared. Different metrics are used for the assessment of the system performance, including channel capacity, in two frequency bands, sub-6 GHz (5.9 GHz) and millimeter-wave (mmWave) (26 GHz), under different propagation conditions. The use of beamforming techniques on the vehicle side is compared to conventional SISO and MIMO solutions. In the urban scenario used in the study, a 45° beamwidth circular array is able to enhance the single monopole performance up to 157% in capacity, and outperform MIMO 4×4 in most situations., This work was supported by the Spanish Comision Interministerial de Ciencia y Tecnología (CICYT) under projects TEC2016-78028-C3-1-P, MDM2016-0600, and Catalan Research Group 2017 SGR 219. The Spanish Ministry of Education contributes via a doctoral grant to the first author (FPU17/05561)., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Study of interconnecting switch currents in reconfigurable parasitic layer antennas

  • Ramirez, German
  • Araque, Javier
  • Ballesteros Sánchez, Christian
  • Blanch Boris, Sebastián
  • Romeu Robert, Jordi
  • Cetiner, Bedri Artug
  • Jofre Roca, Lluís
This work presents an approach for calculating the currents across the switches of a reconfigurable parasitic layer intended to add beam-steering capabilities to a reference antenna. The method of analysis is based on the port loading technique in which only one Full-Wave Electromagnetic (FWEM) simulation is required to evaluate the behavior of the reference antenna and its interaction with the reconfigurable layer across all its states. Results show that the currents on the switches are at least one order of magnitude lower than the currents on the feed port of the driven radiator, proving the effectiveness of the reconfigurable parasitic layer approach in implementing Reconfigurable Antenna (RA)., This work was supported by Colciencias convocatoria 727 of 2015 and by the Spanish “Comision Interministerial de Ciencia y Tecnologia” (CI-CYT) under projects TEC2013-47360-C3-1-P, TEC2016-78028-C3-1-P and MDM2016-O6OO, and Catalan Research Group 2017 SGR 219, Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Debye frequency-extended waveguide permittivity extraction for high complex permittivity materials. Concrete setting process characterization

  • Gonzalez, Giselle
  • Blanch Boris, Sebastián
  • Romeu Robert, Jordi
  • Jofre Roca, Lluís
© 2019 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes,creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., A waveguide with central frequency 868 MHz is used in transmission/reflection operation regime to accurately measure the behaviour of the complex permittivity of high complex permittivity granular materials and it has been frequency-extended up to 3 GHz using the Debye fitted relaxation model. It is shown that for highly granular high permittivity materials a waveguide based transmission/reflection technique is necessary to reduce the uncertainty of the extracted permittivity values. The technique is first described and validated with isopropyl alcohol and then applied to the characterization of cement based materials. This paper provides accurate data on the evolution of the complex permittivity of concrete and mortar from the moment of pouring until air dried condition is achieved., Peer Reviewed, Postprint (author's final draft)
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Resonance-based microwave technique for body implant sensing

  • González-López, Giselle|||0000-0002-8050-051X
  • Jofre Roca, L.|||0000-0002-0547-901X
  • García De Valdecasas, S. A.|||0000-0002-2002-526X
  • Rodriguez-Leor, Oriol|||0000-0003-2657-5657
  • Gálvez-Montón, Carolina|||0000-0003-2254-9371
  • Bayés-Genís, Antoni|||0000-0002-3044-197X
  • O'Callaghan, Juan Manuel|||0000-0002-2740-0202
There is an increasing need for safe and simple techniques for sensing devices and prostheses implanted inside the human body. Microwave wireless inspection may be an appropriate technique for it. The implanted device may have specific characteristics that allow to distinguish it from its environment. A new sensing technique based on the principle of differential resonance is proposed and its basic parameters are discussed. This technique allows to use the implant as a signal scattering device and to detect changes produced in the implant based on the corresponding change in its scattering signature. The technique is first tested with a canonic human phantom and then applied to a real in vivo clinical experiment to detect coronary stents implanted in swine animals.