Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 13
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Dispersion relations of generalized one-dimensional phononic crystals

  • Lázaro, Mario|||0000-0003-4949-8295
  • Romero-García, Vicente|||0000-0002-3798-6454
  • Wiltshaw, Richard
  • Craster, Richard V.
[EN] We present a comprehensive method for determining both exact and approximate dispersion relations for one-dimensional resonant phononic crystals, applicable to a wide range of structures, regardless of their specific characteristics. This general framework employs a unified mathematical model, referred to as generalized one-dimensional phononic crystal, in which different types of waves and scatterers/resonators can be considered by adjusting certain parameters. The generalized one-dimensional phononic crystal consists of both a host one-dimensional homogeneous elastic material with physical properties represented in matrix form and an arbitrary set of scatterers within the unit cell, including resonators (discrete and continuous), small material inclusions or variations in cross-sectional area. Based on general assumptions, and imposing the periodicity and Bloch solutions, we develop a matrix-based algorithm using the plane wave expansion method to derive the solution. Additionally, we propose an iterative procedure that provides analytical expressions for the first- and second-order terms, particularly useful in the context of weak scattering. The convergence conditions of the method are rigorously defined. The efficiency of the approach is demonstrated through several numerical examples, highlighting its versatility in different waveguide configurations and scattering scenarios., M.L. and V.R.-G. are grateful for the partial support (grant no. PID2020-112759GB-I00) funded by MCIN/AEI/10.13039/501100011033 and also for the partial support (grant no. PID2023-146237NB-I00) funded by MICIU/AEI/10.13039/501100011033. M.L. and V.R.-G. acknowledge support (grant nos. CIAICO/2022/052 and CIAICO/2024/318) of the 'Programa para la promocion de la investigacion cientifica, el desarrollo tecnologico y la innovacion en la Comunitat Valenciana' funded by Generalitat Valenciana. M.L. is grateful for support (grant no. UNI/551/2021): 'Programa de Recualificacion del Sistema Universitario Espanol para 2021-2023', funded by 'Instrumento Europeo de Recuperacion (Next Generation EU) en el marco del Plan de Recuperacion, Transformacion y Resiliencia de Espana', a traves del Ministerio de Universidades. R.W. and R.V.C. acknowledge financial support from the EU H2020FET-proactive project MetaVEH under grant agreement no. 952039.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Transcription factor-based biosensors for screening and dynamic regulation

  • Tellechea-Luzardo, Jonathan
  • Stiebritz, Martin T.
  • Carbonell, Pablo|||0000-0002-0993-5625
[EN] Advances in synthetic biology and genetic engineering are bringing into the spotlight a wide range of bio-based applications that demand better sensing and control of biological behaviours. Transcription factor (TF)-based biosensors are promising tools that can be used to detect several types of chemical compounds and elicit a response according to the desired application. However, the wider use of this type of device is still hindered by several challenges, which can be addressed by increasing the current metabolite-activated transcription factor knowledge base, developing better methods to identify new transcription factors, and improving the overall workflow for the design of novel biosensor circuits. These improvements are particularly important in the bioproduction field, where researchers need better biosensor-based approaches for screening production-strains and precise dynamic regulation strategies. In this work, we summarize what is currently known about transcription factor-based biosensors, discuss recent experimental and computational approaches targeted at their modification and improvement, and suggest possible future research directions based on two applications: bioproduction screening and dynamic regulation of genetic circuits., JT-L was supported by European Union Marie Sklodowska-Curie Action Individual Postdoctoral Fellowship (Grant agreement ID: 101062593). JT-L was supported by the Next-Generation EU (NGEU) fund through the Spanish Recovery, Transformation and Resilience Plan via a Margarita Salas personal grant from the Spanish Ministry of Universities (UNI/551/2021). MS was supported by the NextGeneration EU (NGEU) fund through the Spanish Recovery, Transformation and Resilience Plan via a María Zambrano personal grant from the Spanish Ministry of Universities (UNI/551/2021). PC acknowledges MCIN/AEI/10.13039/501100011033 funding through PID2020-117271RB-C2 (BIODYNAMICS). PC was supported by the Spanish Ministry of Universities (UNI/551/2021), grant number UP 2021-036 funded by European Union - Next-generation EU. This research received financial support from Generalitat Valenciana through grant CIAICO/2021/159 (SmartBioFab). PC acknowledges MCIN/AEI/10.13039/501100011033 and NextGenerationEU/PRTR funding through grant TED 2021-131049 B-I00 (BioEcoDBTL). PC acknowledges MCIN/AEI/10.13039/501100011033 funding through grant PID 2021-127888NA-I00 (COMPSYNBIO).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

CAD-integrated parametric design and analysis of lightweight shell structures

  • Goldbach, Ann-Kathrin
  • Lazaro, Carlos|||0000-0001-7255-7068
[EN] In the digitalization of planning, analysis and building processes, a streamlined interaction between the conceptual phase and the structural design is of crucial importance to overcome the gap between architecture and engineering. In this paper we show the advantages of performing parametric CAD-integrated design of shell structures by means of an integrated Isogeometric B-Rep Analysis (IBRA) tool that allows to perform Finite Element Analysis directly on trimmed multipatch CAD models. This allows for non-linear analyses and form-finding techniques to be directly applied to complex shapes within the CAD environment -without the need to convert to a simple polygonal mesh- and thus enables structurally informed design iterations at any stage of the design process. We use different hyperbolic-paraboloid geometries and combinations inspired in exemplary works of the shell master F & eacute;lix Candela to highlight the design steps and the potential of the IBRA tool. The examples show that the smooth integration of parametric CAD and analysis model allows the designer to perform a powerful exploration of different configurations and their structural behavior and improve the shape and performance through numerical hanging models., Carlos Lazaro gratefully acknowledges the support for his stay at the Technical University of Munich provided by the Universitat Politecnica de Valencia and the retraining grant of the Spanish Ministry of Universities (RD 289/2021 and UNI/551/2021) funded by the European Union NextGenerationEU program.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Fast biofoundries: coping with the challenges of biomanufacturing

  • Tellechea-Luzardo, Jonathan Alexander
  • Otero-Muras, Irene
  • Goñi-Moreno, Angel
  • Carbonell, Pablo|||0000-0002-0993-5625
[EN] Biofoundries are highly automated facilities that enable the rapid and efficient design, build, test, and learn cycle of biomanufacturing and engineering biology, which is applicable to both research and industrial production. However, developing a biofoundry platform can be expensive and time consuming. A biofoundry should grow organically, starting from a basic platform but with a vision for automation, equipment interoperability, and efficiency. By thinking about strategies early in the process through process planning, simulation, and optimization, bottlenecks can be identified and resolved. Here, we provide a survey of technological solutions in biofoundries and their advantages and limitations. We explore possible pathways towards the creation of a functional, early-phase biofoundry, and strategies towards long-term sustainability., The authors thank Dr Rosalind Le Feuvre, Manchester SYNBIOCHEMCentre, for providing insightful discussions. J.T.-L. was supported by the Next Generation EU (NGEU) fund through the Spanish Recovery, Transformation and Resilience Plan via a Margarita Salas personal grant from the Spanish Ministry of Universities (UNI/551/2021). I.O.-M. was supported by CSIC intramural project PIE 20211CT006. A.G.-M. was supported by the grants BioSinT-CM (Y2020/TCS-6555) and CONTEXT (Atraccion de Talento Program; 2019-T1/BIO-14053) Projects of the Comunidad de Madrid, MULTI-SYSBIO (PID2020-117205GA-I00), and the Severo Ochoa Program for Centres of Excellence in R&D (SEV-2016-0672) (2017-2021) from MCIN/Agencia Estatal de Investigacion of Spain. P.C. was supported by MCIN/AEI/10.13039/501100011033 BIODYNAMICS grant number PID2020-117271RB-C21, and Universitat Politecnica de Valencia Talento Programme.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Computing parameter planes of iterative root-finding methods with several free critical points

  • Campos, Beatriz
  • Canela, Jordi
  • Rodríguez-Arenas, Alberto
  • Vindel, Pura
[EN] In this paper we present an algorithm to obtain the parameter planes of families of root-finding methods with several free critical points. The parameter planes show the joint behaviour of all critical points. This algorithm avoids the inconsistencies arising from the relationship between the different critical points as well as the indeterminacy caused by the square roots involved in their computation. We analyse the suitability of this algorithm by drawing the parameter planes of different Newton-like methods with two and three critical points. We also present some results of the expressions of the Newton-like operators and their derivatives in terms of palindromic polynomials, and we show how to obtain the expression of the critical points of a Newton-like method with real coefficients., The first, second, and fourth authors are supported the project UJI-B2022-46 funded by Universitat Jaume I, Spain. The first and second authors are also supported by the project CIGE/2023/102 funded by Generalitat Valenciana, Spain. The second author is also supported by PID2020-118281GB-C32 (MCIU/AEI/FEDER/UE) . The third author is supported by Accio 3.2 POSDOC/2020/14 of Universitat Jaume I, Spain and by Ayudas Margarita Salas 2021-2023 of Universitat Politecnica de Valencia funded by the Spanish Ministry of Universities (Plan de Recuperacion, Transformacion y Resiliencia) and European Union-Next generation EU (RD 289/2021 and UNI/551/2021) .
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Feasibility of iron-based shape memory alloy strips for shear strengthening of damaged RC beams promoting the formation of plastic hinges

  • Traver-Abella, Celia
  • Ruiz Pinilla, Joaquín Guillermo
  • Monserrat-Lopez, Andrea
  • Montoya-Coronado, Luis A.
  • Ribas, Carlos
  • Cladera, Antoni
  • Miguel Sosa, Pedro|||0000-0001-5395-8149
  • Bonet Senach, José Luís|||0000-0002-6687-5307
[EN] This research focuses on the proof of concept of the feasibility of iron-based shape memory alloys strips (Fe-SMA) to strengthen damaged structures by promoting the yielding of longitudinal reinforcement. For this purpose, an experimental campaign on real-scale reinforced concrete beams previously damaged on shear and retested after being strengthened was carried out. The strengthening technique consists of external Fe-SMA strips wrapping the beams. The results show a very significant increase in both shear strength and ductility. In addition, shear predictions were calculated and compared by several design models. This study highlights the potentialities of Fe-SMA as a strengthening technique for damaged beams on shear., The authors would like to thank the financial support provided by Grants: PID2021-126397OB-I00, PID2021-123701OB-C22, BIA2015-64672-C4-4-R and BIA2015-3 64672-C4-3-R by MCIN/AEI/10.13039/501100011033 and by "ERDF A way of making Europe."; RTI2018-099091-B-C21-AR and RTI2018-099091-B-C22 by MCIN/AEI/10.13039/501100011033 and by "ERDF A way of making Europe" and BIA2015-64672-C4-4-R and BIA2015-64672-C4-3-R (AEI/FEDER, UE); and TED2021-129358B-I00 and TED2021-130272B-C22 funded by MCIN/AEI/10.13039/501100011033 and by the European Union NextGeneration EU/PRTR". The Regional Valencian Government also supported this research with Project AICO/2020/295. Andrea Monserrat is supported by the Ministry of Universities (Spain) with the Recovery, Transformation and Resilience Plan (RD 289/2021 and order UNI/551/2021) funded by NextGenerationEU. The authors thank the Spanish Ministry of Science and Innovation for Grant FPU18/03310 that supported Celia Traver Abella. This research work was undertaken at the Concrete Science and Technology University Institute (ICITECH) of the Universitat Politecnica de Valencia (UPV; Spain), with concrete supplied by Caplansa. They also appreciate the contribution of the re-fer AG Strengthening Solution Company, which provided the memory steel (Fe-SMA strips).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Pure distortion of symmetric box beams with hinged walls

  • Lazaro, Carlos|||0000-0001-7255-7068
  • Martínez-López, Guillermo
  • Bletzinger, Kai-Uwe
  • Wüchner, Roland
[EN] This paper is concerned with the analysis of the pure torsion and distortion of straight box beams with trapezial cross-sections and hinged walls. A one-dimensional mechanical model for this kind of system subjected to anti-symmetric loads on the end cross-sections and no warping constraints is developed. The distortional stiffness of the system is provided by the torsional rigidity of the wall panels. The cross-sectional kinematic condition for which torsion and distortion are uncoupled has been determined. Novel explicit expressions of the internal and external distortional moments, the distortion constant, and the distortional warping pattern have been deduced; they can be directly translated to the classical distortion theory. Results of representative test cases with different section shapes and loads show excellent agreement with finite element models using shell elements. The model is a first step to analyse bridge decks with a distortionable central cell for wind engineering applications. Finally, an extension of the model, including the distortional stiffness provided by the frame bending stiffness of the cross-section walls, is presented. The extended model is applicable to assess the large-scale torsional¿distortional effects in long beams with closed cross sections., This research was carried out during the stay of C. Lazaro at the Chair of Structural Analysis of the Technical University of Munich. This co-author gratefully acknowledges the support for his stay provided by the Universitat Politecnica de Valencia and the retraining grant of the Spanish Ministry of Universities (RD 289/2021 and UNI/551/2021) funded by the European Union NextGenerationEU program. The authors thank also Salvador Monleon (UPV, Valencia) for the interesting discussions on this work.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

New trilobular geometry using advanced materials for experimentally validated enhanced heat transfer in shallow geothermal applications

  • Urchueguía Schölzel, Javier Fermín|||0000-0002-3054-3431
  • Badenes Badenes, Borja|||0000-0002-3469-9265
  • Mateo Pla, Miguel Ángel|||0000-0002-8059-6996
  • Armengot-Carbó, B.|||0000-0001-7424-2975
  • Javadi, Hossein|||0000-0002-2059-7145
[EN] The Adapted Conductivity Trilobular (ACT) design, comprising an up -flow central pipe and three satellite downward pipes, represents a novel configuration of a borehole heat exchanger. The novelty lies not only in the geometry of the heat exchanger, but also in the use of materials perfectly adapted to the thermal use for which they have been specified. The central pipe is constructed of a composite bilayer material with very low thermal conductivity, whereas the satellite pipes are based on a novel highly conductive plastic material. The primary objective behind this design was to simplify installation, by using essentially the same drilling and grouting methods used for conventional single -U or double -U borehole heat exchangers. In response to the rising demand for more efficient and affordable ground heat exchangers to be connected to Ground Source Heat Pump (GSHP) systems, this innovation was one of the promising outcomes of the GEOCOND European project. To assess ACT performance, the Geothermal Laboratory on the campus of the Universitat Politecnica de Valencia conducted a number of thermal response tests (TRTs), the experimental results of which are collected and analyzed in this paper. Additionally, a modified version of the Composite Two Region Line Source modeling scheme is described and used to assess the experimental data. A total of four demonstration boreholes - two single -U baseline and two ACT boreholes - have been tested. The experimental investigation using the C2RLS methodology reveals that the ACT configuration has a significantly lower thermal than the typical BHE arrangement and allows a greater specific heat injection rate. Specifically, a borehole resistance drop from 0.149 (m.K)/W to 0.07 (m.K)/W allowing higher injection rates to be achieved without an unsustainable increase in ground temperature. These findings may have significant implications for the development of more efficient and cost-effective GSHP systems., This work was developed within the European project GEOCOND and continued with the European project GEO4CIVHIC, funded by the European Union's Horizon 2020 research and innovation program, under grant agreement s No 727583 and No 792355, respectively.Acknowledgment to the support from the Program for the Re-qualification of the Spanish university system for 2021-2023 (in the framework of the call of the Universitat Politecnica de Valencia) , subsidized by the European Recovery Instrument (financed by the European Union by Next Generation EU) in the framework of the Spanish Recovery, Transformation and Resilience Plan, through the Ministry of Universities, regulated by RD 289/2021 and Order UNI/551/2021.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Wave propagation in beams with multiple resonators: Conditions for weak scattering and the Born approximation

  • Lázaro, Mario|||0000-0003-4949-8295
  • Romero-García, Vicente|||0000-0002-3798-6454
  • Wiltshaw, Richard
  • Craster, R. V.
[EN] We investigate the conditions necessary for weak scattering in a beam loaded by multiple resonators that support both longitudinal and flexural waves. Using a Green's matrix approach we derive the equations of motion of a one-dimensional elastic waveguide with several point resonators, for any resonator morphology modeled by the transfer matrix method, even when considering the resonators to have any number of natural frequencies. The methodology is based on multiple scattering theory, expressing the response as an infinite series whose convergence is closely linked to the scattering intensity provided by the resonators. The convergence conditions are reduced to the study of the spectral radius of the scattering matrix. Furthermore, the leading order of the multiple scattering expansion is associated with the Born approximation. The results offer approximate expressions for the spectral radius, providing a clear physical interpretation of weak scattering. Several numerical examples are presented to validate the proposed approach, demonstrating its effectiveness and applicability., M.L. and V.R.-G. are grateful for the partial support under Grant No. PID2020-112759GB-I00 funded by MCIN/AEI/10.13039/501100011033, Grant No. PID2023-146237NB-I00 funded by MICIU/AEI/10.13039/501100011033 and Grant No. CIAICO/2024/318 funded by Generalitat Valenciana. V.R.-G. acknowledge also support from Grant No. CIAICO/2022/052 of the "Programa para la promocion de la investigacion cientifica, el desarrollo tecnologico y la innovacion en la Comunitat Valenciana" funded by Generalitat Valenciana. M.L is grateful for support under the Grant UNI/551/2021: "Programa de Recualificacion del Sistema Universitario Espanol para 2021-2023", (funded by "Instrumento Europeo de Recuperacion NextGenerationEU) en el marco del Plan de Recuperacion, Transformacion y Resiliencia de Espana", a traves del Ministerio de Universidades. R.W and R.V.C acknowledge financial support from the EU H2020FET-proactive project MetaVEH under grant agreement number 952039.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

The Influence of Flexural Reinforcement Yielding on the Shear Strength of Reinforced Concrete Beams with and without Shear Reinforcement

  • López, Andrea Montserrat
  • Miguel Sosa, Pedro Francisco
[EN] Statically indeterminate structures such as continuous beams allow redistribution of internal forces. For increasing loads after yielding of the flexural reinforcement, shear forces and flexural deformations may increase, making it possible to reach shear failures even after the full flexural capacity of the structure is developed. An extensive experimental programme consisting of 30 shear tests (15 cantilever tests and 15 continuous beam tests) was carried out to assess the shear strength of reinforced concrete beams with and without shear reinforcement. Some of the tests were designed to fail in shear after yielding of the flexural reinforcement. The main objective of this experimental study was analysing the influence of large flexural strains on shear strength. The tests were instrumented by means of surface measurements using Digital Image Correlation (DIC). These measurements allowed controlling the evolution of strains at concrete surface to obtain the rotation of the plastic hinges and tracking the development and kinematics of the critical shear crack to obtain, by accounting for suitable constitutive models, the contribution of the various shear-transfer actions. The analysis of the test results confirmed the reduction of shear strength provided by concrete with increasing flexural rotation both in tests with and without shear reinforcement. Moreover, this shear strength component weakened for increasing shear reinforcement ratios. The test results were compared with the shear strength values predicted by different design codes, showing that these formulations did not properly capture the loss of shear strength caused by plastic deformation. The proposed simplified method to calculate the shear strength of the plastic hinges accounting for the plastic rotation demand shows consistent agreement for the experimental results., [ES] Las estructuras hiperestáticas, tales como las vigas continuas, permiten la redistribución de esfuerzos internos, de forma que, tras la plastificación de la armadura de flexión, el esfuerzo cortante y la deformación pueden aumentar con el incremento de las cargas aplicadas, siendo posible alcanzar roturas por cortante incluso después de agotar la capacidad resistente por flexión de la estructura. En este artículo se presenta un extenso programa experimental constituido por 30 ensayos de cortante (15 ensayos de voladizo y 15 ensayos de vigas continuas) llevado a cabo para evaluar la resistencia a cortante de vigas de hormigón armado con y sin armadura de cortante, algunas de ellas diseñadas para fallar a cortante tras la plastificación de la armadura de flexión. El principal objetivo de este estudio experimental era analizar la influencia del desarrollo de grandes deformaciones de flexión en la resistencia a cortante. Durante los ensayos, se empleó la Correlación Digital de Imágenes (DIC) para obtener medidas de deformación superficiales. Estas medidas permitieron analizar la evolución de las deformaciones en la superficie de hormigón para obtener la rotación de las rótulas plásticas y hacer un seguimiento del desarrollo y la cinemática de la fisura crítica de cortante con el objetivo de obtener, considerando los modelos constitutivos adecuados, la contribución a la resistencia de los distintos mecanismos de transferencia de cortante. El análisis de los resultados confirmó la reducción de la componente de la resistencia a cortante proporcionada por el hormigón con el aumento de la rotación de flexión, tanto en los especímenes con armadura de cortante como sin ella. Además, esta componente de la resistencia a cortante resultó menor cuanto mayor era cuantía de armadura de cortante. Los resultados se compararon con los valores de resistencia propuestos por distintos códigos de diseño, mostrando que estas formulaciones no capturan adecuadamente la reducción de resistencia a cortante causada por la deformación plástica. El método simplificado que se propone para el cálculo de la resistencia a cortante de las rótulas plásticas considerando la demanda de rotación plástica predice resultados coherentes respecto a los obtenidos experimentalmente., This research was funded with grants from the Ministerio de Economia y Competitividad (Spain) with Research Project BIA2015-64672-C4-4-R. Andrea Monserrat was particularly supported by the Conselleria d'Educacio, Investigacio, Cultura i Esport of the Generalitat Valenciana (Order 6/2015, DOCV no. 7615 15.09.2015) funded with European Regional Development Funds (ERDF) as a predoctoral researcher and by the Ministerio de Universidades (Spain) with the Recovery, Transformation and Resilience Plan (RD 289/2021 and order UNI/551/2021) funded by NextGenerationEU as a postdoctoral researcher.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Fast biofoundries: coping with the challenges of biomanufacturing

  • Tellechea-Luzardo, Jonathan
  • Otero-Muras, Irene
  • Goñi-Moreno, Ángel
  • Carbonell-Bejerano, Pablo
Biofoundries are highly automated facilities that enable the rapid and efficient design, build, test, and learn cycle of biomanufacturing and engineering biology, which is applicable to both research and industrial production. However, developing a biofoundry platform can be expensive and time consuming. A biofoundry should grow organically, starting from a basic platform but with a vision for automation, equipment interoperability, and efficiency. By thinking about strategies early in the process through process planning, simulation, and optimization, bottlenecks can be identified and resolved. Here, we provide a survey of technological solutions in biofoundries and their advantages and limitations. We explore possible pathways towards the creation of a functional, early-phase biofoundry, and strategies towards long-term sustainability., The authors thank Dr Rosalind Le Feuvre, Manchester SYNBIOCHEM Centre, for providing insightful discussions. J.T.-L. was supported by the Next Generation EU (NGEU) fund through the Spanish Recovery, Transformation and Resilience Plan via a Margarita Salas personal grant from the Spanish Ministry of Universities (UNI/551/2021). I.O.-M. was supported by CSIC intramural project PIE 20211CT006. A.G.-M. was supported by the grants BioSinT-CM (Y2020/TCS-6555) and CONTEXT (Atracción de Talento Program; 2019-T1/BIO-14053) Projects of the Comunidad de Madrid, MULTI-SYSBIO (PID2020-117205GA-I00), and the Severo Ochoa Program for Centres of Excellence in R&D (SEV-2016-0672) (2017–2021) from Ministe. P.C. was supported by MCIN/AEI/10.13039/501100011033 BIODYNAMICS grant number PID2020-117271RB-C21, and Universitat Politécnica de València Talento Programme., Peer reviewed
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Spatio-temporal modeling for record-breaking temperature events in Spain

  • Castillo-Mateo, Jorge
  • Gelfand, Alan E.
  • Gracia-Tabuenca, Zeus
  • Asín, Jesús
  • Cebrián, Ana C.
Record-breaking temperature events are now very frequently in the news, viewed as evidence of climate change. With this as motivation, we undertake the first substantial spatial modeling investigation of temperature record-breaking across years for any given day within the year. We work with a dataset consisting of over 60 years (1960–2021) of daily maximum temperatures across peninsular Spain. Formal statistical analysis of record-breaking events is an area that has received attention primarily within the probability community, dominated by results for the stationary record-breaking setting with some additional work addressing trends. Such effort is inadequate for analyzing actual record-breaking data. Resulting from novel and detailed exploratory data analysis, we propose rich hierarchical conditional modeling of the indicator events which define record-breaking sequences. After suitable model selection, we discover explicit trend behavior, necessary autoregression, significance of distance to the coast, useful interactions, helpful spatial random effects, and very strong daily random effects. Illustratively, the model estimates that global warming trends have increased the number of records expected in the past decade almost 2-fold, 1.93 (1.89,1.98), but also estimates highly differentiated climate warming rates in space and by season. Supplementary materials for this article are available online, including a standardized description of the materials available for reproducing the work.
e-cienciaDatos, Repositorio de Datos del Consorcio Madroño
Datos de investigación Set de datos (Dataset)

Understanding self-assembly across scales in BODIPY derivatives: from supramolecular aggregation in solution to optical-waveguiding crystalline materials

  • González Sánchez, Marina
  • Garcia, Ana M.
  • Valera, Jorge S
  • Rodríguez Fernández-Pacheco, Ana María
  • Cabanillas Gonzalez, Juan
  • Prieto Recio, Maria Pilar
<p>Molecular self-assembly constitutes a useful tool to construct discrete and functional nanostructures with well-defined properties. Nevertheless, understanding supramolecular order in solution and its transmission to the solid state for the same scaffold remains challenging and the impact of this transition in the properties of the resulting supramolecular architectures is still underexplored, thus limiting the application of self-assembly in fields like organic electronics. Herein we explore the supramolecular aggregation process of a chiral BODIPY derivative in solution, their features in solid state, and its potential application as optical waveguide. In solution, this derivative follows a time-dependent self-assembly process, ultimately leading to aggregates of increasing dimensionality with propensity to precipitate, from which a certain degree of crystallinity can be inferred. The subsequent formation of single crystals confirms the preservation of key supramolecular features from solution to the solid state. Notably, the one-centimeter-long crystals obtained present active optical waveguiding behavior in the NIR with a remarkable optical loss coefficient, the first optical loss reported for BODIPY crystals. These results highlight the value of studying self-assembly across different scales and demonstrate the potential of BODIPY-based systems for the development of optical waveguides with remarkable performance.</p> <p>The dataset id organized in three main folders, including all the spectroscopic, xrd and optical waveguiding measurements, provided in tabular data and images forms.</p>