Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 71
Encontrada(s) 1 página(s)

Minerva. Repositorio Institucional de la Universidad de Santiago de Compostela
Publication Artículo científico (JournalArticle)

Ferroelectric Domain Walls in PbTiO3 Are Effective Regulators of Heat Flow at Room Temperature

  • Langenberg Pérez, Eric
  • Saha, Dipanjan
  • Holtz, Megan E.
  • Wang, Jian-Jun
  • Bugallo Ferrón, David
  • Ferreiro Vila, Elías
  • Paik, Hanjong
  • Hanke, Isabelle
  • Ganschow, Steffen
  • Muller, David A.
  • Chen, Long-Qing
  • Catalan, Gustau
  • Domingo, Neus
  • Malen, Jonathan
  • Schlom, Darrell G.
  • Rivadulla Fernández, José Francisco
Achieving efficient spatial modulation of phonon transmission is an essential step on the path to phononic circuits using “phonon currents”. With their intrinsic and reconfigurable interfaces, domain walls (DWs), ferroelectrics are alluring candidates to be harnessed as dynamic heat modulators. This paper reports the thermal conductivity of single-crystal PbTiO3 thin films over a wide variety of epitaxial-strain-engineered ferroelectric domain configurations. The phonon transport is proved to be strongly affected by the density and type of DWs, achieving a 61% reduction of the room-temperature thermal conductivity compared to the single-domain scenario. The thermal resistance across the ferroelectric DWs is obtained, revealing a very high value (≈5.0 × 10–9 K m2 W–1), comparable to grain boundaries in oxides, explaining the strong modulation of the thermal conductivity in PbTiO3. This low thermal conductance of the DWs is ascribed to the structural mismatch and polarization gradient found between the different types of domains in the PbTiO3 films, resulting in a structural inhomogeneity that extends several unit cells around the DWs. These findings demonstrate the potential of ferroelectric DWs as efficient regulators of heat flow in one single material, overcoming the complexity of multilayers systems and the uncontrolled distribution of grain boundaries, paving the way for applications in phononics
Minerva. Repositorio Institucional de la Universidad de Santiago de Compostela
Publication Artículo científico (JournalArticle)

Tuning coherent-phonon heat transport in LaCoO3/SrTiO3 Superlattices

  • Rivadulla Fernández, José Francisco
  • Bugallo Ferrón, David
  • Langenberg Pérez, Eric
  • Carbo-Argibay, Enrique
  • Varela Domínguez, Noa
  • Otero Fumega, Adolfo
  • Pardo Castro, Víctor
  • Lucas del Pozo, Irene
  • Morellón Alquézar, Luis Alberto
Accessing the regime of coherent phonon propagation in nanostructures opens enormous possibilities to control the thermal conductivity in energy harvesting devices, phononic circuits, etc. In this paper we show that coherent phonons contribute substantially to the thermal conductivity of LaCoO3/SrTiO3 oxide superlattices, up to room temperature. We show that their contribution can be tuned through small variations of the superlattice periodicity, without changing the total superlattice thickness. Using this strategy, we tuned the thermal conductivity by 20% at room temperature. We also discuss the role of interface mixing and epitaxial relaxation as an extrinsic, material dependent key parameter for understanding the thermal conductivity of oxide superlattices
Minerva. Repositorio Institucional de la Universidad de Santiago de Compostela
Publication Artículo científico (JournalArticle)

Apparent auxetic to non-auxetic crossover driven by Co2+ redistribution in CoFe2O4 thin films

  • Ferreiro Vila, Elías
  • Iglesias Bernardo, Lucía
  • Lucas del Pozo, Irene
  • Varela Domínguez, Noa
  • Bui, Cong Tinh
  • Rivas Murias, Beatriz
  • Vila Fungueiriño, José Manuel
  • Jiménez Cavero, Pilar
  • Magén, Cesar
  • Morellón, Luis
  • Pardo Castro, Víctor
  • Rivadulla Fernández, José Francisco
Oxide spinels of general formula AB2O4 (A = Mg2+, Fe2+; B = Al3+, Cr3+, etc.) constitute one of the most abundant crystalline structures in mineralogy. In this structure, cations distribute among octahedral and tetrahedral sites, according to their size and the crystal-field stabilization energy. The cationic arrangement determines the mechanical, magnetic, and transport properties of the spinel and can be influenced by external parameters like temperature, pressure, or epitaxial stress in the case of thin films. Here, we report a progressive change in the sign of the Poisson ratio, ν, in thin films of CoFe2O4, defining a smooth crossover from auxetic (ν < 0) to non-auxetic (ν > 0) behavior in response to epitaxial stress and temperature. Microstructural and magnetization studies, as well as ab initio calculations, demonstrate that such unusual elastic response is actually due to a progressive redistribution of Co2+ among the octahedral and tetrahedral sites of the spinel structure. The results presented in this work clarify a long standing controversy about the magnetic and elastic properties of Co-ferrites and are of general applicability for understanding the stress-relaxation mechanism in complex crystalline structures.
Minerva. Repositorio Institucional de la Universidad de Santiago de Compostela
Publication Artículo científico (JournalArticle)

Observation of nuclear-spin Seebeck effect

  • Kikkawa, Takashi
  • Reitz, Derek
  • Ito, H.
  • Makiuchi, Takahiko
  • Sugimoto, T.
  • Tsunekawa, K.
  • Daimon, Shunsuke
  • Oyanagi, Koichi
  • Ramos Amigo, Rafael Enrique
  • Takahashi, Satoshi
  • Shiomi, Yuki
  • Tserkovnyak, Yaroslav
  • Saitoh, Eiji
Thermoelectric effects have been applied to power generators and temperature sensors that convert waste heat into electricity. The effects, however, have been limited to electrons to occur, and inevitably disappear at low temperatures due to electronic entropy quenching. Here, we report thermoelectric generation caused by nuclear spins in a solid: nuclear-spin Seebeck effect. The sample is a magnetically ordered material MnCO3 having a large nuclear spin (I = 5/2) of 55Mn nuclei and strong hyperfine coupling, with a Pt contact. In the system, we observe low-temperature thermoelectric signals down to 100 mK due to nuclear-spin excitation. Our theoretical calculation in which interfacial Korringa process is taken into consideration quantitatively reproduces the results. The nuclear thermoelectric effect demonstrated here offers a way for exploring thermoelectric science and technologies at ultralow temperatures
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Enhanced thermo-spin effects in iron-oxide/metal multilayers

  • Ramos, Pablo
  • Lucas, Irene
  • Algarabel, Pedro A.
  • Morellón, Luis
  • Uchida, K.
  • Saitoh, E.
  • Ibarra, M. Ricardo
Since the discovery of the spin Seebeck effect (SSE), much attention has been devoted to the study of the interaction between heat, spin, and charge in magnetic systems. The SSE refers to the generation of a spin current upon the application of a thermal gradient and detected by means of the inverse spin Hall effect. Conversely, the spin Peltier effect (SPE) refers to the generation of a heat current as a result of a spin current induced by the spin Hall effect. Here we report a strong enhancement of both the SSE and SPE in Fe3O4/Pt multilayered thin films at room temperature as a result of an increased thermo-spin conversion efficiency in the multilayers. These results open the possibility to design thin film heterostructures that may boost the application of thermal spin currents in spintronics., This work was supported by ERATO ‘Spin Quantum Rectification Project’ (Grant No. JPMJER1402) and PRESTO ‘Phase Interfaces for Highly Efficient Energy Utilization’ (Grant No. JPMJPR12C1) from JST, Japan; Grantin-Aid for Scientific Research (A) (Grant No. JP15H02012) and Grant-in-Aid for Scientific Research on Innovative Area, ‘Nano Spin Conversion Science’ (Grant No. JP26103005) from JSPS KAKENHI, Japan, the NEC Corporation, and the Noguchi Institute. The microscopy works were conducted in the Laboratorio de Microscopías Avanzadas at INA, Universidad de Zaragoza; H2020-MSCA-RISE-2016 SPICOLOST (Grant No. 734187); the Spanish Ministry of Economy and Competitiveness (Grant No. MAT2017-82970-C2, including FEDER), Spain; and the Aragón regional government (E26), Spain., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Terahertz spin currents and inverse spin Hall effect in thin-film heterostructures containing complex magnetic compounds

  • Seifert, T.
  • Martens, U.
  • Günther, S.
  • Schoen, M. A. W.
  • Radu, F.
  • Chen, X. Z.
  • Lucas, Irene
  • Ramos, R.
  • Aguirre, Myriam H.
  • Algarabel, Pedro A.
  • Anadón, Arturo
  • Körner, H. S.
  • Walowski, J.
  • Back, C.
  • Ibarra, M. Ricardo
  • Morellón, Luis
  • Saitoh, E.
  • Wolf, M.
  • Song, Cunfeng
  • Uchida, K.
  • Münzenberg, M.
  • Radu, I.
  • Kampfrath, T.
Terahertz emission spectroscopy (TES) of ultrathin multilayers of magnetic and heavy metals has recently attracted much interest. This method not only provides fundamental insights into photoinduced spin transport and spin–orbit interaction at highest frequencies, but has also paved the way for applications such as efficient and ultrabroadband emitters of terahertz (THz) electromagnetic radiation. So far, predominantly standard ferromagnetic materials have been exploited. Here, by introducing a suitable figure of merit, we systematically compare the strength of THz emission from X/Pt bilayers with X being a complex ferro-, ferri- and antiferromagnetic metal, that is, dysprosium cobalt (DyCo5), gadolinium iron (Gd24Fe76), magnetite (Fe3O4) and iron rhodium (FeRh). We find that the performance in terms of spin-current generation not only depends on the spin polarization of the magnet's conduction electrons, but also on the specific interface conditions, thereby suggesting TES to be a highly interface-sensitive technique. In general, our results are relevant for all applications that rely on the optical generation of ultrafast spin currents in spintronic metallic multilayers., This work was supported by ERATO "Spin Quantum Rectification Project" (Grant No. JPMJER1402) and PRESTO "Phase Interfaces for Highly Efficient Energy Utilization" (Grant No. JPMJPR12C1) from JST, Japan, Grant-in-Aid for Scientific Research (A) (JP15H02012), Grant-inAid for Scientific Research on Innovative Area "Nano Spin Conversion Science" (Grant No. JP26103005) from JSPS KAKENHI, Japan and H2020-MSCA-RISE-2016 SP1COLOST (Grant No. 734187). The authors acknowledge support by the Spanish Ministry of Economy and Competitiveness (through Project Nos. MAT2014-51982-C-R, including FEDER funding) and the Aragon Regional government (Project No. E26). I.R. acknowledges funding from German Ministry for Education and Research (BMBF) through project 05K16BCA Femto-THz-X. T. S. and T. K. acknowledge funding through the ERC H2020 CoG project TERAMAG/grant No. 681917 and through the DFG priority program SPP 1538/SpinCaT., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Apparent auxetic to non-auxetic crossover driven by Co2+ redistribution in CoFe2O4 thin films

  • Ferreiro-Vila, Elías
  • Iglesias, Lucia
  • Lucas, Irene
  • Varela-Dominguez, Noa
  • Bui, Cong Tinh
  • Rivas-Murias, B.
  • Vila-Fungueiriño, José M.
  • Jiménez-Cavero, Pilar
  • Magén, César
  • Morellón, Luis
  • Pardo, Victor
  • Rivadulla, Francisco
Oxide spinels of general formula AB2O4 (A = Mg2+, Fe2+; B = Al3+, Cr3+, etc.) constitute one of the most abundant crystalline structures in mineralogy. In this structure, cations distribute among octahedral and tetrahedral sites, according to their size and the crystal-field stabilization energy. The cationic arrangement determines the mechanical, magnetic, and transport properties of the spinel and can be influenced by external parameters like temperature, pressure, or epitaxial stress in the case of thin films. Here, we report a progressive change in the sign of the Poisson ratio, ν, in thin films of CoFe2O4, defining a smooth crossover from auxetic (ν < 0) to non-auxetic (ν > 0) behavior in response to epitaxial stress and temperature. Microstructural and magnetization studies, as well as ab initio calculations, demonstrate that such unusual elastic response is actually due to a progressive redistribution of Co2+ among the octahedral and tetrahedral sites of the spinel structure. The results presented in this work clarify a long standing controversy about the magnetic and elastic properties of Co-ferrites and are of general applicability for understanding the stress-relaxation mechanism in complex crystalline structures., This work has received financial support from Ministerio de Economía y Competitividad (Spain) under Project No. MAT2016-80762-R and MAT2017-82970-C2-R, Xunta de Galicia (Centro singular de investigación de Galicia accreditation 2016-2019, No. ED431G/09), the European Union (European Regional Development Fund-ERDF), and the European Commission through the Horizon H2020 funding by H2020-MSCA-RISE-2016-Project No. 734187–SPICOLOST., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Exploring tantalum as a potential dopant to promote the thermoelectric performance of zinc oxide

  • Arias, B. I.
  • Xie, Wenjie
  • Aguirre, Myriam H.
  • Tobaldi, David M.
  • Sarabando, Artur R.
  • Rasekh, Sh.
  • Mikhalev, Sergey M.
  • Frade, Jorge R.
  • Weidenkaff, Anke
  • Kovalevsky, A. V.
This article belongs to the Special Issue Recent Advances in Thermoelectric Materials., Zinc oxide (ZnO) has being recognised as a potentially interesting thermoelectric material, allowing flexible tuning of the electrical properties by donor doping. This work focuses on the assessment of tantalum doping effects on the relevant structural, microstructural, optical and thermoelectric properties of ZnO. Processing of the samples with a nominal composition Zn1−xTaxO by conventional solid-state route results in limited solubility of Ta in the wurtzite structure. Electronic doping is accompanied by the formation of other defects and dislocations as a compensation mechanism and simultaneous segregation of ZnTa2O6 at the grain boundaries. Highly defective structure and partial blocking of the grain boundaries suppress the electrical transport, while the evolution of Seebeck coefficient and band gap suggest that the charge carrier concentration continuously increases from x = 0 to 0.008. Thermal conductivity is almost not affected by the tantalum content. The highest ZT~0.07 at 1175 K observed for Zn0.998Ta0.002O is mainly provided by high Seebeck coefficient (−464 μV/K) along with a moderate electrical conductivity of ~13 S/cm. The results suggest that tantalum may represent a suitable dopant for thermoelectric zinc oxide, but this requires the application of specific processing methods and compositional design to enhance the solubility of Ta in wurtzite lattice., This research was funded by FCT individual grant SFRH/BPD/124238/2016; project CICECO-Aveiro Institute of Materials (ref. UID/CTM/50011/2019), Project of Bilateral Cooperation between FCT and DAAD (Germany) and the project POCI-01-0145-FEDER-031875, financed by COMPETE 2020 Program and National Funds through the FCT/MEC and when applicable cofinanced by FEDER under the PT2020 Partnership Agreement. TEM work was financed by H2020-MSCA-RISE-2016 SPICOLOST (Grant No. 734187) and has been conducted at Advanced Microscopy Laboratory INA- Universidad de Zaragoza. David M. Tobaldi is grateful to the Portuguese National Funds (OE), through FCT and IP, within the scope of the framework contract provided for by numbers 4, 5 and 6 of Article 23, of the Decree-Law 57/2016, of August 29, changed by Law 57/2017, of July 19., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Interface-induced anomalous Nernst effect in Fe3O4/Pt-based heterostructures

  • Ramos, R.
  • Kikkawa, T.
  • Anadón, Arturo
  • Lucas, Irene
  • Niizeki, T.
  • Uchida, K.
  • Algarabel, Pedro A.
  • Morellón, Luis
  • Aguirre, Myriam H.
  • Ibarra, M. Ricardo
  • Saitoh, E.
We have studied the anomalous Nernst effect (ANE) in [Fe3O4/Pt]-based heterostructures grown at high temperature, by measuring the ANE-induced electric field with a magnetic field applied normal to the sample surface, in the perpendicular magnetized configuration, where only the ANEs from the ferromagnetic layers or magnetic proximity effects can be detected. An ANE voltage is observed for [Fe3O4/Pt]n multilayers, and we further investigated its origin by performing measurements in [Fe3O4/Pt/Fe3O4] trilayers as a function of the Pt thickness. Our results suggest the presence of an interface-induced ANE in the metallic layer, possibly driven by a heat induced subnanometer interdiffusion which affects the nature of the Fe3O4/Pt interface. Despite this ANE, the spin Seebeck effect is the dominant mechanism for the transverse thermoelectric voltage in the in-plane magnetized configuration, accounting for about 70% of the voltage in the multilayers., This work was supported by the ERATO “Spin Quantum Rectification Project” (Grant No. JPMJER1402) and PRESTO “Phase Interfaces for Highly Efficient Energy Utilization” (Grant No. JPMJPR12C1) from JST, Japan; Grant-in-Aid for Scientific Research (A) (Grant No. JP15H02012), Grant-in-Aid for Scientific Research on Innovative Area, “Nano Spin Conversion Science” (Grant No. JP26103005) and Grant-in-Aid for Research Activity Start-up (No. JP18H05841) from JSPS KAKENHI, Japan; H2020-MSCA-RISE-2016 SPICOLOST (Grant No. 734187); and the Spanish Ministry of Economy and Competitiveness (Grant No. MAT2017-82970-C2, including FEDER) and the Aragon regional government (E26), Spain. The microscopy works were conducted in the LMA at INA, Universidad de Zaragoza. A.A. acknowledges MINECO [through Project Nos. FIS2016-78591-C3-1-R (SKYTRON), PCIN-2015-111 (SOgraph), and SEV-2016-0686] and Comunidad de Madrid through Grant No. S2018/NMT-4321 (NANOMAGCOST-CM)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Interfacial ferromagnetism and atomic structures in high-temperature grown Fe3O4/Pt/Fe3O4 epitaxial trilayers

  • Kikkawa, T.
  • Suzuki, M.
  • Ramos, R.
  • Aguirre, Myriam H.
  • Okabayashi, J.
  • Uchida, K.
  • Lucas, Irene
  • Anadón, Arturo
  • Kikuchi, D.
  • Algarabel, Pedro A.
  • Morellón, Luis
  • Ibarra, M. Ricardo
  • Saitoh, E.
Induced Pt ferromagnetism in Fe3O4/Pt/Fe3O4 epitaxial trilayer films has been investigated by means of X-ray magnetic circular dichroism (XMCD) at the Pt L3,2-edges at various temperatures from 300K to 12K, including the metal-insulator transition temperature of Fe3O4 (TV∼114K). At all the temperatures, we observed clear XMCD signals due to Pt ferromagnetism, the amplitude of which was determined to be 0.39μB at 300K and 0.52μB at 12K for the sample with the Pt thickness of ∼2nm. Interestingly, these values are comparable to or even greater than those in Pt/3d-ferromagnetic-metal (Fe, Ni, Co, and Ni81Fe19) junction systems. The results can be interpreted in terms of a possible Fe interdiffusion into the Pt layer and also possible Fe-Pt alloying due to its high-temperature deposition., This work was supported by the ERATO “Spin Quantum Rectification Project” (No. JPMJER1402) from JST, Japan, the Grant-in-Aid for Scientific Research on Innovative Area “Nano Spin Conversion Science” (No. JP26103005), the Grant-in-Aid for Scientific Research (B) (No. JP18H01465), the Grant-in-Aid for Research Activity Start-up (No. JP19K21031) from JSPS KAKENHI, Japan, the World Premier International Research Center Initiative (WPI) from MEXT, Japan, the H2020-MSCA-RISE-2016 SPICOLOST (No. 734187), the Spanish Ministry of Economy and Competitiveness (No. MAT2017-82970-C2, including FEDER), and the Aragon regional government (E26), Spain., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Nanoscale magnetic and charge anisotropies at manganite interfaces

  • Carreira, Santiago J.
  • Aguirre, Myriam H.
  • Briatico, Javier
  • Steren, Laura B.
Strong correlated manganites are still under intense research owing to their complex phase diagrams in terms of Sr-doping and their sensitivity to intrinsic and extrinsic structural deformations. Here, we performed X-ray absorption spectroscopy measurements of manganite bilayers to explore the effects that a local Sr-doping gradient produce on the charge and antiferromagnetic anisotropies. In order to gradually tune the Sr-doping level along the axis perpendicular to the samples we have grown a series of bilayers with different thicknesses of low-doped manganites (from 0 nm to 6 nm) deposited over a La0.7Sr0.3MnO3 metallic layer. This strategy permitted us to resolve with high accuracy the thickness region where the charge and spin anisotropies vary and the critical thickness tc over which the out of plane orbital asymmetry does not have any further modifications. We found that the antiferromagnetic spin axis points preferentially out of the sample plane regardless the capping layer thickness. However, it tilts partially into the sample plane far from this critical thickness, owing to the combined contributions of the external structural strain and electron doping. Furthermore, we found that the doping level of the capping layer strongly affects the critical thickness, giving clear evidence of the influence exerted by the electron doping on the orbital and magnetic configurations. These anisotropic changes induce subtle modifications on the domain reorientation of La0.7Sr0.3MnO3, as evidenced from the magnetic hysteresis cycles., Authors thanks the financial support of FONCYT PICT 2014-1047, CONICET PIP 112-201501-00213, MINCYT and the European Commission through the Horizon H2020 funding by H2020-MSCA-RISE-2016 – Project No. 734187 – SPICOLOST., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Pulsed current-voltage electrodeposition of stoichiometric Bi2Te3 nanowires and their crystallographic characterization by transmission electron backscatter diffraction

  • Manzano, Cristina V.
  • Polyakov, Mikhail N.
  • Maiz, Jon
  • Aguirre, Myriam H.
  • Maeder, Xavier
  • Martín-González, Marisol
Bi2Te3 nanowires with diameters ranging from 25 to 270 nm, ultra-high aspect ratio, and uniform growth front were fabricated by electrodeposition, pulsing between zero current density during the off time and constant potential during the on time (pulsed-current-voltage method, p-IV). The use of zero current density during the off time is to ensure no electrodeposition is carried out and the system is totally relaxed. By this procedure, stoichiometric nanowires oriented perpendicular to the c-axis is obtained for the different diameters of porous alumina templates. In addition, the samples show a uniform growth front with ultra-high aspect ratio single crystal nanowires. The high degree of crystallinity was verified by transmission electron backscatter diffraction. This characterization revealed that the nanowires present both large single crystalline areas and areas with alternating twin configurations., The authors would like to acknowledge partial financial support from ERC StG NanoTEC 240497, National Project No. MAT2017-86450-C4-3-R, and Intramural Infante CSIC 201550E072. M. H. A wants to acknowledge the financial support of European Commission through H2020 MSCARISE 2016, Project "SPICOLOST" No 734187 which are funding the access to LMA-INA equipment of Transmission Electron Microscopy., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Room-temperature AFM electric-field-induced topotactic transformation between perovskite and brownmillerite SrFeOx with sub-micrometer spatial resolution

  • Ferreiro-Vila, Elías
  • Blanco-Canosa, Santiago
  • Lucas, Irene
  • Vasili, Hari Babu
  • Magén, César
  • Ibarra, Alfonso
  • Rubio-Zuazo, J.
  • Castro, Germán R.
  • Morellón, Luis
  • Rivadulla, Francisco
Reversible structural transformations between perovskite (PV) ABO3−δ and brownmillerite (BM) ABO2.5 (A = Ca2+, Sr2+; B = Fe4+/3, Co4+/3+) oxides can be induced by topotactic oxygen exchange at moderate temperatures under reducing/oxidizing conditions. The combination of a large oxide-ion conduc-tivity and a small free energy difference between the 4+/3+ oxidation states of many 3d transition metal ions enables these topotactic transformations. Herein, it is demonstrated that the electric field produced by a voltage-biased atomic force microscopy tip can induce such transformation between PV SrFeO3−δ and BM SrFeO2.5 at room temperature and with sub-micrometer spatial resolution. Interestingly, the structural transformation is kept after the electric field is removed, allowing a nonvolatile control of the local chemical, electrical, optical, and magnetic properties. Thus, the results presented in this paper open the door for the fabrication of stable ionic-based devices through the electric field patterning of different crystallographic phases., This work has received financial support from Ministerio de Economía y Competitividad (Spain) under Project Nos. MAT2016-80762-R, MAT2017-82970-C2-R, and PGC2018-101334-A-C22, Xunta de Galicia (Centro singular de investigación de Galicia accreditation 2016-2019, ED431G/09), the European Union (European Regional Development Fund-ERDF), and the European Commission through the Horizon H2020 funding by H2020-MSCA-RISE-2016 under Project No. 734187-SPICOLOST. This project has received funding from the European’s Union Horizon 2020 research and innovation programme under Grant No. 823717-ESTEEM3., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Topotactic transformation in SrFeO3−δ triggered by low-dose Ga+ focused ion irradiation

  • Ferreiro-Vila, Elías
  • Bugallo, David
  • Magén, César
  • Rivadulla, Francisco
  • Teresa, José María de
We introduce a single-step lithography process based on Ga+-focused ion beam (FIB) irradiation to trigger a topotactic transformation on SrFeO3−δ thin films, from the perovskite to the brownmillerite (BM) crystal structure. The crystallographic transformation is triggered by preferential oxygen sputtering by Ga+-FIB irradiation, which favors the formation of the SrFeO2.5 BM phase. The transformation has been verified through micro-Raman spectroscopy on thin films subjected to Ga+-FIB irradiation under 5 kV and 30 kV. Inducing crystallographic transformations by FIB in a single-step process (without the need of resists), at a very high speed (low Ga+ doses are required, in the range of 1015 ions/cm2), with very high spatial resolution (limited by the ion beam spot, of a few square nanometers) and with potential for upscaling using broad Ga+ beams, this approach represents a significant forward step over previous methods using multistep lithographic or electrochemical procedures. All these virtues make this process appealing to develop applications based not only on SrFeO3−δ thin films but also on other oxide films harnessing topotactic transformations., This work was supported by the Spanish Ministry of Economy and Competitivity through Project Nos. MAT2017-82970-C2-2-R, MAT2018-102627-T, and MAT2016-80762-R (including FEDER funds), by the Aragon Regional Government through Project No. E13_20R (with European Social Fund), by Xunta de Galicia (Centro singular de investigación de Galicia accreditation 2016–2019, No. ED431G/09), and by the European Union (European Regional Development Fund-ERDF) and the European Commission through the Horizon H2020 funding by H2020-MSCA-RISE-2016-Project No. 734187–SPICOLOST. D.B. acknowledges financial support from Ministerio de Ciencia e Investigación (Spain) through an FPI fellowship (No. BES-2017-079688)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Nanoscale structural characterization of manganite thin films integrated to silicon correlated with their magnetic and electric properties

  • Carrero, Aneely
  • Román, Augusto
  • Aguirre, Myriam H.
  • Steren, Laura B.
A detailed nanoscale structural characterization was performed on high-quality La0.66Sr0.33MnO3 (LSMO) thin films of different thicknesses and deposited by pulsed laser deposition onto buffered Si (100) substrates. A multilayered structure built of Y0.13Zr0.87O2 (YSZ) and CeO2 layers was used as buffer in order to optimize the manganite films growth. The stacking of the different layers, their morpholohy, composition and strains were analysed using different experimental techniques. In-situ characterization of the films, performed with reflection high-energy electron diffraction, revealed their epitaxial growth and smooth surfaces. High-resolution transmission electron microscopy (HR-TEM) images showed sharp interfaces between the constituents lattices and combined with energy-dispersive X-ray analysis allowed us to determine that there was no ion interdifussion across them. The Fourier-Fast-Transform of the HR-TEM images was used to resolve the epitaxy relationship between the layers, resulting in [100] LSMO (001) ‖ [110] CeO2 (001) ‖ [110] YSZ (001) ‖ [110] Si (001). The LSMO thin films were found to be ferromagnetic and metallic at low temperature regardless their thickness. The effect of strains and defects was only detected in films thinner than 15 nm and put in evidence by X-ray diffraction patterns and correlated with magnetic and electrical parameters., This work was supported by FONCYT PICT 2014-1047 and 2016-0867, CONICET PIP 112-201501-00213, MINCYT and the H2020-MSCA-RISE-2016 SPICOLOST (N° 734187) ., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Redox engineering of strontium titanate-based thermoelectrics

  • Kovalevsky, A. V.
  • Zakharchuk, Kiryl V.
  • Aguirre, Myriam H.
  • Xie, Wenjie
  • Patrício, Sonia G.
  • Ferreira, Nuno M.
  • Lopes, Diogo
  • Sergiienko, Sergii A.
  • Constantinescu, G.
  • Mikhalev, Sergey M.
  • Weidenkaff, Anke
  • Frade, Jorge R.
The development of thermoelectrics for high-temperature applications imposes several essential requirements on the material properties. In some energy-conversion scenarios, the cost and thermal stability requirements may dominate over efficiency issues, making abundant, high-temperature-stable and low-toxic oxides attractive alternative thermoelectric materials. As compared to “traditional” thermoelectrics, oxides possess unique redox flexibility and defect chemistry, which can be precisely tuned by external temperature and oxygen partial pressure conditions. This work aims to demonstrate how, by redox-sensitive substitutions, the thermoelectric properties of oxides can be tuned and enhanced. The proposed strategy is exemplified by considering molybdenum-containing strontium titanate within nominally single-substituted and nanocomposite concepts. The involved materials design allows us to proceed from an in-depth understanding of the redox-promoted effects to the demonstration of the enhanced thermoelectric performance attained by redox engineering. Synergistic enhancement of the Seebeck coefficient and suppression of the thermal conductivity due to combined carrier filtering effects and efficient phonon scattering at redox-induced interfaces provided up to 25% increase in the thermoelectric performance. The results demonstrate extraordinary flexibility of the perovskite lattice towards retaining a rich combination of the molybdenum redox states and shifting their ratio by tuning the A-site stoichiometry, and the prospects for developing new materials combining thermoelectric and (electro)catalytic functionalities., This work was supported by the project CICECO-Aveiro Institute of Materials (ref. UIDB/50011/2020 & UIDP/50011/2020) and the project POCI-01-0145-FEDER-031875, financed by COMPETE 2020 Program and National Funds through the FCT/MEC and when applicable co-financed by FEDER under the PT2020 Partnership Agreement, by the project UID/EMS/00481/2019-FCT and by Centro 2020, through the European Regional Development Fund (ERDF), in the scope of the project CENTRO-01-0145-FEDER-022083. SGP, NMF and SMM also acknowledge the support of national funds (OE), through FCT – Fundação para a Ciência e a Tecnologia, I.P., in the scope of the framework contract foreseen in the numbers 4, 5 and 6 of the article 23, of the Decree-Law 57/2016, of August 29, changed by Law 57/2017, of July 19. The authors are thankful to Prof. Carlos Sá (CEMUP) for performing XPS studies and helpful discussion of the results. TEM work was financed by H2020-MSCA-RISE-2016 SPICOLOST (Grant No. 734187) and has been conducted at Advanced Microscopy Laboratory INA – Universidad de Zaragoza., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Selective activation of memristive interfaces in TaO x -based devices by controlling oxygen vacancies dynamics at the nanoscale

  • Ferreyra, C.
  • Sánchez, M. J.
  • Aguirre, Myriam H.
  • Acha, C.
  • Bengió, S.
  • Lecourt, J.
  • Lüders, Ulrike
  • Rubi, Diego
The development of novel devices for neuromorphic computing and non-traditional logic operations largely relies on the fabrication of well controlled memristive systems with functionalities beyond standard bipolar behavior and digital ON–OFF states. In the present work we demonstrate for Ta2O5-based devices that it is possible to selectively activate/deactivate two series memristive interfaces in order to obtain clockwise or counter-clockwise multilevel squared remanent resistance loops, just by controlling both the electroforming process and the (a)symmetry of the applied stimuli, and independently of the nature of the used metallic electrodes. Based on our thorough characterization, analysis and modeling, we show that the physical origin of this electrical behavior relies on controlled oxygen vacancies electromigration between three different nanoscopic zones of the active Ta2O5−x layer: a central one and two quasi-symmetric interfaces with reduced TaO2−h(y) layers. Our devices fabrication process is rather simple as it implies the room temperature deposition of only one CMOS compatible oxide—Ta-oxide—and one metal, suggesting that it might be possible to take advantage of these properties at low cost and with easy scability. The tunable opposite remanent resistance loops circulations with multiple—analogic—intermediate stable states allows mimicking the adaptable synaptic weight of biological systems and presents potential for non-standard logic devices., We acknowledge support from INN-CNEA, UNCuyo (06/C455), ANPCyT (PICT2014-1382, PICT2016-0867, PICT2017-1836, PICT 2017-0984), CONICET (PIP 11220150100653CO) and Univ. Buenos Aires (UBACyT 20020170100284BA). MA also acknowledges financial support of H2020-MSCA-RISE2016 SPICOLOST Grant No. 734187 to perform TEM studies at LMA-INA, University of Zaragoza. SB thanks technical support from N Cortes., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Tunable resistivity exponents in the metallic phase of epitaxial nickelates

  • Guo, Qikai
  • Farokhipoor, Saeedeh
  • Magén, César
  • Rivadulla, Francisco
  • Noheda, Beatriz
We report a detailed analysis of the electrical resistivity exponent of thin films of NdNiO3 as a function of epitaxial strain. Thin films under low strain conditions show a linear dependence of the resistivity versus temperature, consistent with a classical Fermi gas ruled by electron-phonon interactions. In addition, the apparent temperature exponent, n, can be tuned with the epitaxial strain between n = 1 and n = 3. We discuss the critical role played by quenched random disorder in the value of n. Our work shows that the assignment of Fermi/Non-Fermi liquid behaviour based on experimentally obtained resistivity exponents requires an in-depth analysis of the degree of disorder in the material., Qikai Guo and Saeedeh Farokhipoor acknowledge financial support from a China Scholarship Council (CSC) grant and a VENI grant (016.veni.179.053) of the Netherlands Organisation for Scientific Research (NWO), respectively. Francisco Rivadulla acknowledges support by the Ministry of Science of Spain (Project No. MAT2016-80762-R), the Conselleria de Cultura, Educacion e Ordenacion Universitaria. Xunta de Galicia (ED431F 2016/008, and Centro singular de investigación de Galicia accreditation 2016–2019, ED431G/09), the European Union (European Regional Development Fund (ERDF)) and the European Commission through the project 734187- SPI-COLOST (H2020-MSCA-RISE-2016)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Ferroelectric domain walls in PbTiO3 are effective regulators of heat flow at room temperature

  • Langenberg, Eric
  • Saha, Dipanjan
  • Holtz, Megan E.
  • Wang, Jian-Jun
  • Bugallo, David
  • Ferreiro-Vila, Elías
  • Paik, Hanjong
  • Hanke, Isabelle
  • Ganschow, Steffen
  • Muller, David A.
  • Chen, Long-Qing
  • Catalán, Gustau
  • Domingo, Neus
  • Malen, Jonathan
  • Schlom, Darrell G.
  • Rivadulla, Francisco
Achieving efficient spatial modulation of phonon transmission is an essential step on the path to phononic circuits using “phonon currents”. With their intrinsic and reconfigurable interfaces, domain walls (DWs), ferroelectrics are alluring candidates to be harnessed as dynamic heat modulators. This paper reports the thermal conductivity of single-crystal PbTiO3 thin films over a wide variety of epitaxial-strain-engineered ferroelectric domain configurations. The phonon transport is proved to be strongly affected by the density and type of DWs, achieving a 61% reduction of the room-temperature thermal conductivity compared to the single-domain scenario. The thermal resistance across the ferroelectric DWs is obtained, revealing a very high value (≈5.0 × 10–9 K m2 W–1), comparable to grain boundaries in oxides, explaining the strong modulation of the thermal conductivity in PbTiO3. This low thermal conductance of the DWs is ascribed to the structural mismatch and polarization gradient found between the different types of domains in the PbTiO3 films, resulting in a structural inhomogeneity that extends several unit cells around the DWs. These findings demonstrate the potential of ferroelectric DWs as efficient regulators of heat flow in one single material, overcoming the complexity of multilayers systems and the uncontrolled distribution of grain boundaries, paving the way for applications in phononics., This work has received financial support from Ministerio de Economia y Competitividad (Spain) under project no. MAT2016-80762-R, Xunta de Galicia (Centro singular de investigacion de Galicia accreditation 2016-2019, ED431 G/09), the European Union (European Regional Development Fund-ERDF), and the European Commission through the Horizon H2020 funding by H2020-MSCA-RISE-2016 project no. 734187-SPICOLOST. E.L. acknowledges the funding received from the European Union’s Horizon 2020 research and innovation program through the Marie Skłodowska-Curie Actions: Individual Fellowship-Global Fellowship (ref. MSCAIF-GF-708129). D.B. acknowledges financial support from MINECO (Spain) through an FPI fellowship (BES-2017- 079688). The work at Cornell was supported by the Army Research Office under grant W911NF-16-1-0315. H.P. acknowledges support from the National Science Foundation [Platform for the Accelerated Realization, Analysis, and Discovery of Interface Materials (PARADIM)] under cooperative agreement no. DMR-1539918., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Large thermoelectric power variations in epitaxial thin films of layered perovskite GdBaCo2O5.5±δ with a different preferred orientation and strain

  • Chatterjee, Arindom
  • Chávez-Angel, Emigdio
  • Ballesteros, Belén
  • Caicedo, José Manuel
  • Padilla-Pantoja, Jessica
  • Leborán, Victor
  • Sotomayor Torres, C. M.
  • Rivadulla, Francisco
  • Santiso, José
This work describes the growth of thin epitaxial films of the layered perovskite material GdBaCo2O5.5±δ (GBCO) on different single crystal substrates SrTiO3 (STO), (LaAlO3)0.3(Sr2TaAlO6)0.7 (LSAT) and LaAlO3 (LAO) as an approach to study changes in the thermoelectric properties by means of the induced epitaxial strain. In addition to strain changes, the films grow with considerably different preferred orientations and domain microstructures: GBCO films on STO are purely c-axis oriented (c⊥) with an average 0.18% in-plane tensile strain; GBCO on LSAT is composed of domains with a mixed orientation (c‖ and c⊥) with an average 0.71% in-plane compressive strain; while on LAO it is b-axis oriented (c‖) with an average 0.89% in-plane compressive strain. These differences result in important cell volume changes, as well as in the orthorhombicity of the a–b plane of the GBCO structure, which in turn induce a change in the sign and temperature dependence of the thermopower, while the electrical conductivity remains almost unchanged. In general, compressively strained films show negative S thermopower (n-type) while tensile strained films show a positive S (p-type) at low temperatures, probing the adaptive nature of the GdBaCo2O5.5±δ compound. These results point to the spontaneous generation of oxygen vacancies to partially accommodate the epitaxial stress as the main cause for this effect., This work was supported by the projects: MINECO ref. MAT2016-77100-C2-1-P and CNRS-CSIC PICS Project ref. 261091, the EU for funding through project H2020-MSCA-RISE-2014 ref. 645658, and the AGAUR agency for 2017SGR327. ICN2 is funded by the CERCA programme/Generalitat de Catalunya and by the Severo Ochoa programme of the Spanish Ministry of Economy, Industry and Competitiveness (MINECO, grant no. SEV-2017-0706). CMS and ECA acknowledge support from the support from the Spanish MICINN project SIP (PGC2018-101743-B-I00). AC particularly acknowledges the support of the Severo Ochoa programme and ICN2 for his PhD grant. FR acknowledges support from MAT2016-80762-R, Xunta de Galicia (Centro singular de investigación de Galicia accreditation 2016–2019, ED431G/09), by the European Union (European Regional Development Fund-ERDF) and the European Commission through the Horizon H2020 funding by H2020-MSCA-RISE-2016-Project No. 734187 – SPICOLOST., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Reduction of thermal conductivity in ferroelectric SrTiO3 thin films

  • Sarantopoulos, Alexandros
  • Saha, Dipanjan
  • Ong, Wee-Liat
  • Magén, César
  • Malen, Jonathan A.
  • Rivadulla, Francisco
Bulk SrTiO3 is a quantum paraelectric in which an antiferrodistortive distortion below ≈105 K and quantum fluctuations at low temperature preclude the stabilization of a long-range ferroelectric state. However, biaxial mechanical stress, impurity doping, and Sr nonstoichiometry, among other mechanisms, are able to stabilize a ferroelectric or relaxor ferroelectric state at room temperature, which develops into a longer-range ferroelectric state below 250 K. In this paper, we show that epitaxial SrTiO3 thin films grown under tensile strain on DyScO3 exhibit a large reduction of thermal conductivity, of ≈60% at room temperature, with respect to identical strain-free or compressed films. The thermal conductivity shows a further reduction below 250 K, a temperature concurrent with the peak in the dielectric constant [J. H. Haeni et al., Nature (London) 430, 758 (2004)]. These results suggest that strain gradients in the relaxor and ferroelectric phase of SrTiO3 are very effective phonon scatterers, limiting the thermal transport in this material., F.R. acknowledges financial support of the Ministerio de Economía y Competitividad of Spain (Project No. MAT2016- 80762-R), and Xunta de Galicia (Centro Singular de Investigación de Galicia accreditation 2016-2019) and the European Union (European Regional Development Fund ERDF), and the European Commission through the project 734187 - SPICOLOST (H2020-MSCA-RISE-2016). J.A.M. would like to acknowledge the National Science Foundation, Division of Electrical, Communication and Cyber Systems, Award No. 1901972. This work was supported by the National Natural Science Foundation of China (Grant No. 51876186), Natural Science Foundation of Zhejiang Province (Grant No. LZ19E060002), the Fundamental Research Funds for the Central Universities (K20200145), and ZJUI with W.-L. Ong as one of the Principal Supervisors., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Deconvolution of Phonon Scattering by Ferroelectric Domain Walls and Point Defects in a PbTiO3Thin Film Deposited in a Composition-Spread Geometry

  • Bugallo, David
  • Langenberg, Eric
  • Ferreiro-Vila, Elías
  • Smith, Eva H.
  • Stefani, Christina
  • Batlle, Xavier
  • Catalán, Gustau
  • Domingo, Neus
  • Schlom, Darrell G.
  • Rivadulla, Francisco
We present a detailed analysis of the temperature dependence of the thermal conductivity of a ferroelectric PbTiO3 thin film deposited in a composition-spread geometry enabling a continuous range of compositions from ∼25% titanium deficient to ∼20% titanium rich to be studied. By fitting the experimental results to the Debye model we deconvolute and quantify the two main phonon-scattering sources in the system: ferroelectric domain walls (DWs) and point defects. Our results prove that ferroelectric DWs are the main agent limiting the thermal conductivity in this system, not only in the stoichiometric region of the thin film ([Pb]/[Ti] ≈ 1) but also when the concentration of the cation point defects is significant (up to ∼15%). Hence, DWs in ferroelectric materials are a source of phonon scattering at least as effective as point defects. Our results demonstrate the viability and effectiveness of using reconfigurable DWs to control the thermal conductivity in solid-state devices., This work received financial support from the Ministerio de Economía y Competitividad (Spain) under project nos. MAT2016-80762-R, PID2019-104150RB-100, and PGC2018-097789-B-I00, Xunta de Galicia (Centro Singular de Investigación de Galicia Accreditation 2019-2022, ED431G 2019/03), the European Union (European Regional Development Fund-ERDF), and the European Commission through the Horizon H2020 funding by H2020-MSCA-RISE-2016-Project No. 734187-SPICOLOST. E.L. is a Serra Húnter Fellow (Generalitat de Catalunya). E.L. acknowledges funding received from the European Union’s Horizon 2020 Research and Innovation Program through the Marie Skłodowska-Curie Actions: Individual Fellowship-Global Fellowship (ref. MSCA-IF-GF-708129). D.B. acknowledges financial support from MINECO (Spain) through an FPI fellowship (BES-2017-079688). The work at Cornell was supported by the Army Research Office under grant W911NF-16-1-0315. H.P. acknowledges support from the National Science Foundation [Platform for the Accelerated Realization, Analysis, and Discovery of Interface Materials (PARADIM)] under Cooperative Agreement No. DMR-1539918.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Characterization of W-type hexaferrite thin films prepared by chemical solution deposition

  • Soroka, Miroslav
  • Buršík, Josef
  • Kužel, Radomír
  • Prokleška, Jan
  • Aguirre, Myriam H.
Thin films of W-type hexaferrite were grown on SrTiO3(111) single crystals using the chemical solution deposition method and metalorganic precursor solutions prepared using the modified Pechini method. The synthesis of single-phase materials required optimizing the initial stoichiometry and crystallization conditions. The results showed that a concurrent excess of alkaline earth metal and deficiency in divalent metal ion (Zn2+, Co2+) favors the synthesis of pure W hexaferrites. This off-stoichiometry suppressed the formation of an exceedingly stable spinel phase at pyrolysis temperatures. The epitaxial nature of thin films, expressed as the orientation relation (00l)W || (111)SrTiO3 and [110] W || [112] SrTiO3 and hence the pronounced anisotropy of their magnetic properties as well were established by three dimensional x-ray diffraction texture analysis and magnetization measurements, respectively and enabled to identify the temperature interval in which the characteristic spin reorientation transition occurs for a specific degree of cobalt substitution., This work was supported by the Czech Science Foundation, Grant No. 19-06433S, by the Research Infrastructure NanoEnviCz (Ministry of Education, Youth and Sports of the Czech Republic, Projects No. LM2018124), by the “NanoCent” Project No. CZ.02.1.01/0.0/0.0/15_003/0000485, ERDF. Authors also acknowledge financial support of H2020-MSCA-RISE-2016 SPICOLOST Grant No. 734187 (TEM analysis, at LMA-INA, University of Zaragoza)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Dependence of the composition, morphology and magnetic properties with the water and air exposure during the Fe1-yO/Fe3O4 core–shell nanoparticles synthesis

  • Lohr, Javier
  • Vásquez Mansilla, Marcelo
  • Gerbaldo, M. V.
  • Moreno, M. Sergio
  • Tobia, Dina
  • Goya, Gerardo F.
  • Winkler, Elin L.
  • Zysler, Roberto Daniel
  • Lima Jr., Enio
The thermal decomposition of organometallic precursors in the presence of surfactants and a long-chain alcohol is a valuable method to synthesize magnetic nanoparticles (MNPs) because it provides good control of the final morphology and crystallinity of the magnetic material. These parameters, and consequently the magnetic properties, depend on several details of the experimental procedure of chemical synthesis. We have studied the role of the pre-decomposition step, heating the system to 373–393 K in inert gas flux, on the final composition and morphology of the system. By adding this intermediate step, we were able to produce MNPs with a Fe1-yO/Fe3O4 core–shell structure and sizes of 20–25 nm. When the same synthesis protocol was used skipping the pre-decomposition stage, monophasic MNPs of 11 nm with ferrite structure were obtained. These differences in the composition have a major effect on the resulting magnetic properties of MNPs, and are related to some by-reactions in the synthesis solution during the preparation procedure., The authors acknowledge the financial support of the Argentinian Agencia Nacional de Promoción de Ciencia y Tecnológica (ANPCyT) through the project nos. PICT-2016–0288 and PICT-2018–02565. The authors also thank the Universidad Nacional de Cuyo (UNCuyo) by the financial support through the project nos. 06/C527 and 06/C528. The authors also acknowledge the support of the EU commission under the grant H2020-MSCA-RISE-2016, SPICOLOST project no. 734187. GFG thanks the Spanish Ministerio de Ciencia, Innovación y Universidades by the partial financial support through project PID2019-106947RB-C21., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Quantification of the interfacial and bulk contributions to the longitudinal spin Seebeck effect

  • Jiménez-Cavero, Pilar
  • Lucas, Irene
  • Bugallo, David
  • López-Bueno, Carlos
  • Ramos, Rafael
  • Algarabel, Pedro A.
  • Ibarra, M. Ricardo
  • Rivadulla, Francisco
  • Morellón, Luis
We report the disentanglement of bulk and interfacial contributions to the thermally excited magnon spin current in the spin Seebeck effect under static heating. For this purpose, we have studied the dependence of the inverse spin Hall voltage and the thermal conductivity on the magnetic layer thickness. Knowledge of these quantities allows us to take into account the influence of both sources of thermal spin current in the analysis of the voltage dependence. The magnetic layer thickness modulates the relative magnitude of the involved thermal drops for a fixed total thermal difference throughout the sample. In the end, we attain the separate contributions of both sources of thermal spin current—bulk and interfacial—and obtain the value of the thermal magnon accumulation length scale in maghemite, which we find to be 29(1) nm. According to our results, bulk magnon accumulation dominates the spin Seebeck effect in our studied range of thicknesses, but the interfacial component is by no means negligible., This work was supported by the Spanish Ministry of Science [through Project Nos. MAT2014-51982-C2-R, MAT2016-80762-R, MAT2017-82970-C2-R, and PID2019-104150RB-I00 (including FEDER funding) and the Aragón Regional government (Project No. E26)]. P.J.-C. acknowledges Spanish MECD for support through FPU program (Reference No. FPU014/02546). D.B. acknowledges support from MINECO (Spain) through an FPI program (No. BES-2017-079688). R.R. also acknowledges support from the European Commission through the Project No. 734187-SPICOLOST (H2020-MSCA-RISE-2016), the European Union's Horizon 2020 research and innovation program through the Marie Sklodowska-Curie Actions Grant Agreement SPEC No. 894006, and the Spanish Ministry of Science (No. RYC 2019-026915-I). Authors acknowledge the Advanced Microscopy Laboratory-INA University of Zaragoza for offering access to their instruments. C. L-B. acknowledges Xunta de Galicia and ESF for a PhD Grant (ED481A-2018/013)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Tuning coherent-phonon heat transport in LaCoO3/SrTiO3 superlattices

  • Bugallo, David
  • Langenberg, Eric
  • Carbó-Argibay, Enrique
  • Varela Dominguez, Noa
  • Fumega, Adolfo O.
  • Pardo, Victor
  • Lucas, Irene
  • Morellón, Luis
  • Rivadulla, Francisco
Accessing the regime of coherent phonon propagation in nanostructures opens enormous possibilities to control the thermal conductivity in energy harvesting devices, phononic circuits, etc. In this paper we show that coherent phonons contribute substantially to the thermal conductivity of LaCoO3/SrTiO3 oxide superlattices, up to room temperature. We show that their contribution can be tuned through small variations of the superlattice periodicity, without changing the total superlattice thickness. Using this strategy, we tuned the thermal conductivity by 20% at room temperature. We also discuss the role of interface mixing and epitaxial relaxation as an extrinsic, material dependent key parameter for understanding the thermal conductivity of oxide superlattices., This work has received financial support from Ministerio de Economía y Competitividad (Spain) under project Nos. MAT2016-80762-R and PID2019-104150RB-I00, Xunta de Galicia (Centro singular de investigación de Galicia accreditation 2019-2022, ED431G 2019/03), the European Union (European Regional Development Fund-ERDF), and the European Commission through the Horizon H2020 funding by H2020-MSCA-RISE-2016- Project No. 734187-SPICOLOST. E.L. is a Serra Húnter Fellow (Generalitat de Catalunya). D.B. acknowledges financial support from MINECO (Spain) through an FPI fellowship (BES-2017-079688). V.P. and A.O.F. were supported by the MINECO of Spain through the project PGC2018-101334-B-C21. A.O.F. thanks MECD for the financial support received through the FPU grant FPU16/02572., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Observation of anomalously large magnetoelectric coupling in the hexagonal Z-type ferrite films

  • Woo Shin, Kwang
  • Soroka, Miroslav
  • Shahee, Aga
  • Kim, Kee Hoon
  • Buršík, Josef
  • Kužel, Radomír
  • Vronka, Marek
  • Aguirre, Myriam H.
Although the bulk hexaferrites are known to exhibit strong magnetoelectric (ME) effects near room temperature, the same effects are not realized in a thin film form. Herein, the growth of nearly epitaxial Co2Z-type hexaferrite Ba0.3Sr2.7Co2Fe24O41 (BSCFO) thin films on a SrTiO3 (111) substrate by a chemical solution deposition method is reported. The reciprocal space mapping on the annealed BSCFO films reveals broadening along the qx directions in the (0014) and (0018) peaks, indicating that the oxygen planes belonging to the off-centered octahedra have randomly distributed out-of-plane tilt to indicate significant disorder in the crystallographic orientation. Quantitative investigations reveal that both ME susceptibility and modulated electric polarization (ΔP) by magnetic field up to 370 K in the BSCFO films are always larger than those of the Co2Z-type single crystal by ≈2–15 times and further increase upon having enhanced qx broadening in the (0014) and (0018) peaks. As the off-centered octahedral sites can be a primary source of ΔP as predicted by the p–d hybridization mechanism, these results indicate that effective off-centering could be further enhanced by the orientational disorder. This study identifies the potential of applying the ME hexaferrite films for multifunctional devices., This work was financially supported by the National Research Foundation of S. Korea through 2019R1A2C2090648, 2019M3E4A1080227, and by the Ministry of Education of S. Korea through 2021R1A6C101B418. The works in Czech were supported by the GACR (Czech Science Foundation) Project Nos. 19-06433S and H2020-MSCA-RISE-2016 SPICOLOST under Grant No. 734187 for TEM analysis at LMA-INA, University of Zaragoza, and by the Nanomaterial Center for Advanced Applications(NANOCENT), No. CZ.02.1.01/0.0/0.0/15_003/0000485., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Onion-like Fe3O4/MgO/CoFe2O4 magnetic nanoparticles: new ways to control magnetic coupling between soft and hard magnetic phases

  • Nuñez, Jorge M.
  • Hettler, Simon
  • Lima Jr., Enio
  • Goya, Gerardo F.
  • Arenal, Raúl
  • Zysler, Roberto Daniel
  • Aguirre, Myriam H.
  • Winkler, Elin L.
The control of magnetization inversion dynamics is one of the main challenges driving the design of new nanostructured magnetic materials for magnetoelectronic applications. Nanoparticles with an onion-like architecture offer a unique opportunity to expand the possibilities of combining different phases at the nanoscale and also modulating the coupling between magnetic phases by introducing spacers into the same structure. Here, we report the fabrication, by a three-step high temperature decomposition method, of Fe3O4/MgO/CoFe2O4 onion-like nanoparticles and their detailed structural analysis, elemental compositional maps and magnetic response. The core/shell/shell nanoparticles present epitaxial growth and cubic shape with an overall size of (29 ± 6) nm. These nanoparticles consist of a cubic iron oxide core of 22 ± 4nm in size covered by two shells, the inner of magnesium oxide and the outer of cobalt ferrite of thicknesses ∼1 and ∼2.5 nm, respectively. The magnetization measurements show a single reversion magnetization curve and the enhancement of the coercivity field, from HC ∼ 608 Oe for the Fe3O4/MgO to HC ∼ 5890 Oe for the Fe3O4/MgO/CoFe2O4 nanoparticles at T = 5 K, ascribed to the coupling between both ferrimagnetic phases with a coupling constant of Jc = 2 erg cm−2. The system also exhibits an exchange bias effect, where the exchange bias field increases up to HEB ∼ 2850 Oe at 5 K accompanied by the broadening of the magnetization loop of HC ∼ 6650 Oe. This exchange bias effect originates from the freezing of the surface spins below the freezing temperature TF = 32 K that pinned the magnetic moment of the cobalt ferrite shell., The authors acknowledge financial support from Argentinian governmental agency ANPCyT through Grant No. PICT-2019-02059, PICT-2018-02565 and UNCuyo for support through Grants No. 06/C604 and 06/C605. The authors gratefully acknowledge the EU Commission for financial support through MSCA-RISE projects #734187 (SPICOLOST) and #101007629 (NESTOR). SH was supported by the German Research Foundation (DFG project He 7675/1-1). G. F. G. thanks Spanish State Agency AEI for financial support through project PID2019-106947RB-C21. R. A. gratefully acknowledges the support from the Spanish MICINN (PID2019-104739GB-100/AEI/10.13039/501100011033), Government of Aragon (projects DGA E13-20R) and from the European Union H2020 program “ESTEEM3” (Grant number 823717)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Coexistence of volatile and nonvolatile memristive effects in phase-separated La0.5Ca0.5MnO3-based devices

  • Ramírez, Gerardo
  • Román Acevedo, Wilson
  • Rengifo, Miguel
  • Nuñez, Jorge M.
  • Aguirre, Myriam H.
  • Briático, Javier
  • Rubi, Diego
In this work, we have investigated the coexistence of volatile and nonvolatile memristive effects in epitaxial phase-separated La0.5Ca0.5MnO3 thin films. At low temperatures (50 K), we observed volatile resistive changes arising from self-heating effects in the vicinity of a metal-to-insulator transition. At higher temperatures (140 and 200 K), we measured a combination of volatile and nonvolatile effects arising from the synergy between self-heating effects and ferromagnetic-metallic phase growth induced by an external electrical field. The results reported here add phase separated manganites to the list of materials that can electrically mimic, on the same device, the behavior of both neurons and synapses, a feature that might be useful for the development of neuromorphic computing hardware., We acknowledge support from ANPCyT (Nos. PICT2019-02781 and PICT2020A-00415), EU-H2020-RISE projects MELON (Grant No. 872631), and SPICOLOST (Grant No. 734187)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Annealing effects on the magnetic and magnetotransport properties of iron oxide nanoparticles self-assemblies

  • Fabris, Fernando
  • Lima Jr., Enio
  • Martín Nuñez, Jorge
  • Troiani, Horacio E.
  • Aguirre, Myriam H.
  • Leborán, Victor
  • Rivadulla, Francisco
  • Winkler, Elin L.
In magnetic tunnel junctions based on iron oxide nanoparticles the disorder and the oxidation state of the surface spin as well as the nanoparticles functionalization play a crucial role in the magnetotransport properties. In this work, we report a systematic study of the effects of vacuum annealing on the structural, magnetic and transport properties of self-assembled ∼10 nm Fe3O4nanoparticles. The high temperature treatment (from 573 to 873 K) decomposes the organic coating into amorphous carbon, reducing the electrical resistivity of the assemblies by 4 orders of magnitude. At the same time, the 3.Fe2+/(Fe3++Fe2+) ratio is reduced from 1.11 to 0.13 when the annealing temperature of the sample increases from 573 to 873 K, indicating an important surface oxidation. Although the 2 nm physical gap remains unchanged with the thermal treatment, a monotonous decrease of tunnel barrier width was obtained from the electron transport measurements when the annealing temperature increases, indicating an increment in the number of defects and hot-spots in the gap between the nanoparticles. This is reflected in the reduction of the spin dependent tunneling, which reduces the interparticle magnetoresistance. This work shows new insights about influence of the nanoparticle interfacial composition, as well their the spatial arrangement, on the tunnel transport of self-assemblies, and evidence the importance of optimizing the nanostructure fabrication for increasing the tunneling current without degrading the spin polarized current., The authors are thankful to Argentine government agency Agencia Nacional de Promoción Científica y Tecnológica (ANPCyT) for the financial support of the work through Grant No. PICT-2019-02059, and Universidad Nacional de Cuyo (UNCuyo) for support through Grants No. 06/C029-T1. F Fabris acknowledges the São Paulo Research Foundation (FAPESP) for the post-doctoral fellowship with Grant No. 2019/13678-1. The authors also gratefully acknowledge the European Commission for the financial support under the H2020-MSCA-RISE-2016, SPICOLOST project N° 734187 and H2020-MSCA-RISE-2021 ULTIMATE-I project N° 101007825. FR acknowledges financial support of the Ministerio de Economía y Competitividad of Spain (Project No. MAT2016-80762-R), and Xunta de Galicia (Centro Singular de Investigación de Galicia accreditation 2016–2019) and the European Union (European Regional Development Fund—ERDF)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Magnetization reversal modes and coercive field dependence on perpendicular magnetic anisotropy in FePt thin films

  • Román, Augusto
  • López Pedroso, Agustin
  • Bouzehouane, K.
  • Gómez, J. E.
  • Butera, Alejandro
  • Aguirre, Myriam H.
  • Medeiros Soares, M.
  • García Izquierdo, Carlos
  • Steren, Laura B.
The competition between shape and perpendicular magnetic anisotropies in magnetic thin films gives rise to unusual magnetic behaviors. In ferromagnetic thin films, the presence of an out-of-plane component of the magnetic anisotropy may induce a transition from planar to stripe-like magnetic domains above a critical thickness, tc. In this article, we present a detailed study of the magnetization switching mechanism in FePt thin films, where this phenomenon is observed. Using micromagnetic simulations and experiments, we found that below tc the reversal mechanism is well described by the two-phase model while above this thickness the magnetization within each stripe reverses by coherent rotation. We also analyzed the out-of-plane component of the magnetic anisotropy and its temperature dependence, probing that substrate-induced strains are responsible for the abnormal coercive field behavior observed for FePt films with t > tc., Authors thanks the financial support of FONCYT PICT 0867-2016, PICT 02781-2019 and the European Commission through the Horizon H2020 funding by H2020-MSCA-RISE-2016–Project No. 734187 –SPICOLOST. Beamtime was Granted on the XRD2 beamline by the LNLS. C G acknowledges the financial support received by ANID FONDECYT/REGULAR 1201102, ANID PIA/APOYO AFB180002 and ANID FONDEQUIP EQM140161., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Magnetic transition and spin-polarized two-dimensional electron gas controlled by polarization switching in strained CaMnO3/BaTiO3 slabs

  • Di Napoli, Solange
  • Román, Augusto
  • Llois, A. M.
  • Aguirre, Myriam H.
  • Steren, Laura B.
  • Barral, M. A.
𝐴⁢𝑏𝑖⁢𝑛⁢𝑖⁢𝑡⁢𝑖⁢𝑜 calculations show the presence of a strong magnetoelectric interfacial coupling in a CaMnO3 ultrathin film grown on a strained BaTiO3 ferroelectric film. This heterostructure presents a polarization driven magnetic transition from a G-type to an A-type antiferromagnetic structure. Together with this magnetic transition we find a metallic behavior at the interface between these two insulators, where the charge character of the carriers can be tuned from electrons to holes by switching the electric polarization direction of the ferroelectric film. Besides, the electron gas is spin polarized while the hole gas is not., This work was partially supported by PICT-2016-0867 and PICT-2019-2128 of the ANPCyT, Argentina, and by H2020-MSCA-RISE-2016 SPICOLOST Project No. 734187. We also acknowledge the financial support of European Commission through Marie Skłodowska-Curie Actions H2020 RISE with the projects MELON (Grant No. 872631) and ULTIMATE-I (Grant No. 101007825). Authors would like to acknowledge the access of equipment of “Servicio General de Apoyo a la Investigación (SAI), Universidad de Zaragoza.”, Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Adjusting the Néel relaxation time of Fe3O4/Zn xCo1-xFe2O4core/shell nanoparticles for optimal heat generation in magnetic hyperthermia

  • Fabris, Fernando
  • Lohr, Javier
  • Lima Jr., Enio
  • Almeida, Adriele Aparecida de
  • Troiani, Horacio E.
  • Rodríguez, Luis M.
  • Vásquez Mansilla, Marcelo
  • Aguirre, Myriam H.
  • Goya, Gerardo F.
  • Rinaldi, Daniele
In this work it is shown a precise way to optimize the heat generation in high viscosity magnetic colloids, by adjusting the Néel relaxation time in core/shell bimagnetic nanoparticles, for Magnetic Fluid Hyperthermia applications. To pursue this goal, Fe3O4/ZnxCo1-xFe2O4 core/shell nanoparticles were synthesized with 8.5 nm mean core diameter, encapsulated in a shell of ~1.1 nm of thickness, where the Zn atomic ratio (Zn/(Zn+Co) at%) changes from 33 at% to 68 at%. The magnetic measurements are consistent with a rigid interface coupling between the core and shell phases, where the effective magnetic anisotropy systematically decreases when the Zn concentration increases, without a significant change of the saturation magnetization. Experiments of magnetic fluid hyperthermia of 0.1 wt% of these particles dispersed in water, DMEM (Dulbecco modified Eagles minimal essential medium) and a high viscosity butter oil, result in a large specific loss power (SLP), up to 150 W/g, when the experiments are performed at 571 kHz and 200 Oe. The SLP was optimized adjusting the shell composition, showing a maximum for intermediate Zn concentration. This study shows a way to maximize the heat generation in viscous media like cytosol, for those biomedical applications that requiere smaller particle sizes., The authors acknowledge financial support of Argentinian governmental agency ANPCyT (Project No. PICT-2016-0288 and PICT-2018-02565) and UNCuyo (Project No.06/C527 and 06/C528). The authors gratefully acknowledge the EU-commission financial support under the: H2020-MSCA-RISE-2016, SPICOLOST PROJECT No 734187., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Controlling the dominant magnetic relaxation mechanisms for magnetic hyperthermia in bimagnetic core-shell nanoparticles

  • Fabris, Fernando
  • Lima Jr., Enio
  • De Biasi, Emilio
  • Troiani, Horacio E.
  • Vásquez Mansilla, Marcelo
  • Torres, Teobaldo E.
  • Fernández-Pacheco, Rodrigo
  • Ibarra, M. Ricardo
  • Goya, Gerardo F.
  • Zysler, Roberto Daniel
  • Winkler, Elin L.
We report a simple and effective way to control the heat generation of a magnetic colloid under alternate magnetic fields by changing the shell composition of bimagnetic core–shell Fe3O4/ZnxCo1−xFe2O4 nanoparticles. The core–shell structure constitutes a magnetically-coupled biphase system, with an effective anisotropy that can be tuned by the substitution of Co2+ by Zn2+ ions in the shell. Magnetic hyperthermia experiments of nanoparticles dispersed in hexane and butter oil showed that the magnetic relaxation is dominated by Brown relaxation mechanism in samples with higher anisotropy (i.e., larger concentration of Co within the shell) yielding high specific power absorption values in low viscosity media as hexane. Increasing the Zn concentration of the shell, diminishes the magnetic anisotropy, which results in a change to a Néel relaxation that dominates the process when the nanoparticles are dispersed in a high-viscosity medium. We demonstrate that tuning the Zn contents at the shell of these exchange-coupled core/shell nanoparticles provides a way to control the magnetic anisotropy without loss of saturation magnetization. This ability is an essential prerequisite for most biomedical applications, where high viscosities and capturing mechanisms are present., The authors acknowledge financial support of Argentinian governmental agency ANPCyT (Project No. PICT-2016-0288 and PICT-2015-0883) and UNCuyo (Project No. 06/C527 and 06/C528). The authors gratefully acknowledge the European Community's financial support under the RISE H2020-MSCA-RISE-2016, SPICOLOST project. MRI, GFG and TET also acknowledge the financial support from the Spanish Ministerio de Ciencia, Innovación y Universidades (project MAT2016-78201-P) and the Aragon Regional Government (DGA, Project No. E26)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Effects of Zn substitution in the magnetic and morphological properties of Fe-oxide-based core-shell nanoparticles produced in a single chemical synthesis

  • Lohr, Javier
  • Moreno, M. Sergio
  • Troiani, Horacio E.
  • Goya, Gerardo F.
  • Torres, Teobaldo E.
  • Fernández-Pacheco, Rodrigo
  • Winkler, Elin L.
  • Vásquez Mansilla, Marcelo
  • Rodríguez, Luis M.
  • Zysler, Roberto Daniel
  • Lima Jr., Enio
et al., Magnetic, compositional, and morphological properties of Zn–Fe-oxide core–shell bimagnetic nanoparticles were studied for three samples with 0.00, 0.06, and 0.10 Zn/Fe ratios, as obtained from particle-induced X-ray emission analysis. The bimagnetic nanoparticles were produced in a one-step synthesis by the thermal decomposition of the respective acetylacetonates. The nanoparticles present an average particle size between 25 and 30 nm as inferred from transmission electron microscopy (TEM). High-resolution TEM images clearly show core–shell morphology for the particles in all samples. The core is composed by an antiferromagnetic (AFM) phase with a Wüstite (Fe1–yO) structure, whereas the shell is composed by a ZnxFe3–xO4 ferrimagnetic (FiM) spinel phase. Despite the low solubility of Zn in the Wüstite, electron energy-loss spectroscopy analysis indicates that Zn is distributed almost homogeneously in the whole nanoparticle. This result gives information on the formation mechanisms of the particle, indicating that the Wüstite is formed first, and the superficial oxidation results in the FiM ferrite phase with similar Zn concentration than the core. Magnetization and in-field Mössbauer spectroscopy of the Zn-richest nanoparticles indicate that the AFM phase is strongly coupled to the FiM structure of the ferrite shell, resulting in a bias field (HEB) appearing below TNFeO, with HEB values that depend on the core–shell relative proportion. Magnetic characterization also indicates a strong magnetic frustration for the samples with higher Zn concentration, even at low temperatures., The authors are thankful to the Argentinian Agency ANPCyT for the financial support through the grants PICT 2016-0288, PICT 2015-0118, and PICT 2014-2612. This work was partially supported by FAPESP—Sao Paulo Research Foundation (Brazil, grant number 2016/21371-5). LCCMN is CNPq Fellows under grants 305.647/2015-6. The authors also acknowledge the European Community’s financial support under the RISE H2020-MSCARISE-2016, SPICOLOST project., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Evidence of the spin Seebeck effect in Ni-Zn ferrites polycrystalline slabs

  • Arboleda, J. D.
  • Arnache, O.
  • Aguirre, Myriam H.
  • Ramos, Rafael
  • Anadón, Alberto
  • Ibarra, M. Ricardo
We report on the observation of the spin Seebeck effect in Ni-Zn ferrites slabs with different Zn concentration. All samples have a spinel structure confirmed by XRD and TEM. We fully characterize the magnetic properties by VSM and Mössbauer spectroscopy. Samples exhibit a nonmonotonic magnetization behavior depending on the structural inversion parameter, however we found a spin Seebeck response voltage of about 25.5 nV/K independent of the magnetization and the inversion degree., This work was supported by Solid State Group (GES) at the University of Antioquia in the framework of Sustainability Strategy 2016–2017; Colombian Science, technology and innovation department (COLCIENCIAS, PhD student grant, conv. 567); Municipality of Medellín through SAPIENCIA agency (EnlazaMundos program, conv. 2014). We also thank the Spanish Ministry of Science (through and MAT2014-51982-C2-R, including FEDER funding); the Aragón Regional Government (Project No. E26); and Thermo- Spintronic Marie Curie CIG (Grant Agreement No. 304043)- EU. Project No. PRI-PIBJP-2011-0794. This work was also supported by ERATO Spin Quantum Rectification Project (Grant No. JPMJER1402), Grant-in-Aid for Scientific Research on Innovative Area, Nano Spin Conversion Science (Grant No. JP26103005) from JSPS KAKENHI, Japan, and the NEC Corporation. This work was also supported by H2020-MSCA-RISE-2016 SPICOLOST (Grant No. 734187)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Magnetic hyperthermia experiments with magnetic nanoparticles in clarified butter oil and paraffin: A thermodynamic analysis

  • Almeida, Adriele A. de
  • De Biasi, Emilio
  • Vásquez Mansilla, Marcelo
  • Valdés, Daniela Paola
  • Troiani, Horacio E.
  • Urretavizcaya, Guillermina
  • Torres, Teobaldo E.
  • Rodríguez, Luis M.
  • Fregenal, Daniel E.
  • Bernardi, Guillermo C.
  • Winkler, Elin L.
  • Goya, Gerardo F.
  • Zysler, Roberto Daniel
  • Lima Jr., Enio
In specific power absorption models for magnetic fluid hyperthermia (MFH) experiments, the magnetic relaxation time of nanoparticles (NPs) is known to be a fundamental descriptor of the heating mechanisms. The relaxation time is mainly determined by the interplay between the magnetic properties of NPs and the rheological properties of NPs’ environment. Although the role of magnetism in MFH has been extensively studied, the thermal properties of the NP medium and their changes during MFH experiments have been underrated so far. Herein, we show that ZnxFe3–xO4 NPs dispersed through different media with phase transition in the temperature range of experiment as clarified butter oil (CBO) and paraffin. These systems show nonlinear behavior of the heating rate within the temperature range of MFH experiments. For CBO, a fast increase at ∼306 K is associated with changes in the viscosity (η(T)) and specific heat (cp(T)) of the medium at its melting temperature. This increment in the heating rate takes place around 318 K for paraffin. The magnetic and morphological characterization of NPs together with the observed agglomeration of NPs above 306 and 318 K for CBO and paraffin, respectively, indicate that the fast increase in MFH curves could not be associated with the change in the magnetic relaxation mechanism, with Néel relaxation being dominant. In fact, successive experimental runs performed up to temperatures below and above the CBO and paraffin melting points resulted in different MFH curves due to agglomeration of NPs driven by magnetic field inhomogeneity during the experiments. Our results highlight the relevance of the thermodynamic properties of the system NP-medium for an accurate measurement of the heating efficiency for in vitro and in vivo environments, where the thermal properties are largely variable within the temperature window of MFH experiments., The authors acknowledge financial support of Argentinian governmental agency ANPCyT (project no. PICT-2016-0288 and PICT-2015-0883) and UNCuyo (project no.06/C527 and 06/C528). The authors gratefully acknowledge the EU-Commission financial support under the project: H2020-MSCA-RISE-2016 SPICOLOST project no. 734187. G.F.G. and T.E.T. also acknowledge the financial support from the Spanish Ministerio de Ciencia, Innovación y Universidades (project MAT2016-78201-P) and the Aragon Regional Government (DGA, project no. E26)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Spin Seebeck effect in Y-type hexagonal ferrite thin films

  • Hirschner, J.
  • Maryško, M.
  • Hejtmánek, J.
  • Uhrecký, R.
  • Soroka, Miroslav
  • Buršík, Josef
  • Anadón, Alberto
  • Aguirre, Myriam H.
  • Knížek, K.
The longitudinal spin Seebeck effect (SSE) has been investigated using Pt/ferrite bilayers employing two Y-hexagonal ferrites Ba2⁢Zn2⁢Fe12⁢O22 (Zn2Y) and Ba2⁢Co2⁢Fe12⁢O22 (Co2Y) deposited by a spin-coating method on SrTiO3⁢(111) substrates. The prepared hexagonal ferrites are highly oriented with 𝑐 axes perpendicular to the substrate plane. The room-temperature magnetic moments of both ferrimagnetic ferrites amount to similar values and, most importantly, both have easy magnetization normal to the 𝑐 axis. Despite their similar magnetic response the notable SSE signal is only observed for Zn2Y whereas the SSE signal of Co2Y is below the experimental noise level. A plausible explanation for this surprising discrepancy is magnetic disorder induced by cobalt cations, the random distribution of which in the Co2Y ferrite structure might critically limit the spin-wave propagation. This results in suppression of the SSE signal in Co2Y, while the Zn2Y with nonmagnetic substituent exhibits significant SSE signal. The temperature dependence of SSE for Zn2Y was measured over the 30–300−K range and quantitatively analyzed considering the heat flow through the Pt/Zn2Y bilayer and thermal gradient across the Zn2Y thin layer as the most relevant parameters. Using this approach the normalized SSE smoothly increases with lowering temperature, which correlates to increasing magnon propagation length and magnetization with decreasing temperature., This work was supported by Project No. 14-18392S of the Czech Science Foundation, Grant No. SGS16/245/OHK4/3T/14 of the Czech Technical University in Prague, the Spanish Ministry of Economy and Competitiveness (Grant No. MAT2014-51982-C-R, including FEDER), and the Aragon Regional government (E26). The authors acknowledge the Advanced Microscopy Laboratory-INA, University of Zaragoza for offering access to their instruments. The work was also supported by Thermo-Spintronic FP7-PEOPLE-2011-Marie Curie, CIG Project No. 304043, and SPICOLOST project H2020-MSCA-2016 Grant No. 734187., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Strain-induced magnetic transition in CaMn O3 ultrathin films

  • López Pedroso, Agustin
  • Barral, M. A.
  • Graf, Mónica E.
  • Llois, A. M.
  • Aguirre, Myriam H.
  • Steren, Laura B.
  • Di Napoli, Solange
The effect of high tensile strain and low dimensionality on the magnetic and electronic properties of Ca⁢Mn⁢O3 ultrathin films, epitaxially grown on Sr⁢Ti⁢O3 substrates, are experimentally studied and theoretically analyzed. By means of ab initio calculations, we find that both the high strain produced by the substrate and the presence of the free surface contribute to the stabilization of an in-plane ferromagnetic coupling, giving rise to a nonzero net magnetic moment in the ultrathin films. Coupled with this change in the magnetic order we find an insulator-metal transition triggered by the quantum confinement and the tensile epitaxial strain. Accordingly, our magnetic measurements in 3-nm ultrathin films show a ferromagnetic hysteresis loop, absent in the bulk compound due to its G-type antiferromagnetic structure., This work was partially supported by PICT-2016-0867 of the ANPCyT, Argentina, and by H2020-MSCA-RISE2016 SPICOLOST Project No. 734187., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Tuning the interfacial charge, orbital, and spin polarization properties in La0.67Sr0.33MnO3/La1-xSrxMnO3 bilayers

  • Carreira, Santiago J.
  • Aguirre, Myriam H.
  • Briático, Javier
  • Weschke, Eugen
  • Weschke, Eugen
The possibility of controlling the interfacial properties of artificial oxide heterostructures is still attracting researchers in the field of materials engineering. Here, we used surface sensitive techniques and high-resolution transmission electron microscopy to investigate the evolution of the surface spin-polarization and lattice strains across the interfaces between La0.66Sr0.33MnO3 thin films and low-doped manganites as capping layers. We have been able to fine tune the interfacial spin-polarization by changing the capping layer thickness and composition. The spin-polarization was found to be the highest at a critical capping thickness that depends on the Sr doping. We explain the non-trivial magnetic profile by the combined effect of two mechanisms: On the one hand, the extra carriers supplied by the low-doped manganites that tend to compensate the overdoped interface, favouring locally a ferromagnetic double-exchange coupling. On the other hand, the evolution from a tensile-strained structure of the inner layers to a compressed structure at the surface that changes gradually the orbital occupation and hybridization of the 3d-Mn orbitals, being detrimental for the spin polarization. The finding of an intrinsic spin-polarization at the A-site cation observed in x-ray magnetic circular dichroism (XMCD) measurements also reveals the existence of a complex magnetic configuration at the interface, different from the magnetic phases observed at the inner layers., The authors thank the financial support of FONCYT PICT 2014-1047, CONICET PIP 112-201501-00213, MINCYT, and the European Commission through the Horizon H2020 funding by H2020-MSCA-RISE-2016-Project No. 734187–SPICOLOST., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Structure of ZnxFe3−xO4 nanoparticles studied by neutron diffraction and its relation with their response in magnetic hyperthermia experiments

  • Lohr, Javier
  • Tobia, Dina
  • Torres, Teobaldo E.
  • Rodríguez, Luis M.
  • Puente-Orench, Inés
  • Cuello, Gabriel J.
  • Aguirre, Myriam H.
  • Campo, Javier
  • Aurelio, Gabriela
  • Lima Jr., Enio
The mixed zinc-ferrite spinel magnetic nanoparticles (MNPs) with the general formula ZnxFe3−xO4 are among the most extensively studied families of Fe oxides due to their interesting and diverse chemical, electronic, and magnetic properties. These systems offer the possibility of surface functionalization and possess high biocompatibility, making them highly attractive for applications in biomedicine, such as magnetic fluid hyperthermia (MFH). The efficiency of the MFH process relies on the magnetic, structural and morphological properties of the MNPs. The substitution with the Zn ion and the cationic distribution, as well as the synthesis process employed, have a direct impact on the final properties of these oxides. Therefore, it is essential to have tools that enable a comprehensive characterization of the system to assess its performance in MFH. In this study, we have synthesized four ZnxFe3−xO4 MNP systems using three different methods: two by thermal decomposition at high temperatures, one by co-precipitation, and another by co-precipitation followed by ball milling. We analyze the effect of these various synthesis processes on the magnetic and crystallographic properties, aiming to correlate them with the response of each system in MFH. Neutron diffraction data are employed to determine the cation site occupation and to investigate the correlation with the synthesis method. MFH measurements were conducted in media of diverse viscosities, revealing different values of specific loss power, thus demonstrating a clear dependence on the synthesis process and Zn content., We acknowledge financial support of the European Commission through Marie Skłodowska-Curie Actions H2020 RISE with the projects NESTOR (Grant No. 101007629), SPICOLOST (Grant No. 734187), and ULTIMATE-I (Grant No. 101007825). Also, J.L. and D.T. acknowledge support of ANPCyT though Project No. PICT-2019-01849., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Strain-induced enhancement of spin pumping in Pt/YIG bilayers

  • Solis, Lara M.
  • Carreira, Santiago J.
  • Gómez, Javier
  • Butera, Alejandro
  • Abellán, María
  • García, Carlos
  • Bonetto, Fernando
  • Vavassori, Paolo
  • Briático, Javier
  • Steren, Laura B.
  • Aguirre, Myriam H.
Enhancing spin-to-charge (S→C) conversion efficiency remains a key challenge in spintronic materials research. In this work we investigate the effect of substrate-induced strains onto the S→C efficiency. On one hand, we analyze strains-induced magnetic anisotropies in yttrium iron garnet (Y3Fe5O12, YIG) by comparing the magnetic and structural properties of YIG films grown on Gd3Ga5O12 (GGG) and (CaGd)3(MgZrGa)5O12 (SGGG) substrates. Differences in lattice mismatch—YIG//GGG (η =−0.06%) and YIG//SGGG (η =−0.83%)—lead to out-of-plane tensile strains in the first case and unexpected compressive strain in the latter. On the other hand, we study the spin injection efficiency on Pt/YIG bilayers evaluated by the inverse spin Hall effect (ISHE). We find that the resulting perpendicular magnetic anisotropy in YIG//SGGG, while not dominant over shape anisotropy, correlates with enhanced ISHE signals as observed in spin pumping ferromagnetic resonance and spin Seebeck effect experiments. Strain engineering proves effective in enhancing S→C conversion, providing insight into the design of efficient spintronic devices., This work was partially supported by PICT-2019-02781 ANPCyT and PICT-0415 ANPCyT, Argentina, H2020-MSCA-RISE-2016 Project N∘ 734187 SPICOLOST and MSCA-RISE-2021 Project N∘ 101007825 ULTIMATE-I. Carlos García acknowledges financial support from ANID FONDECYT/REGULAR 1201102, ANID FONDECYT/REGULAR 1241918 and ANID FONDEQUIP EQM140161. María Abellán acknowledge the financial support received by ANID PIA/APOYO AFB230003. The authors would like to thank the ‘Laboratorio de Microscopías Avanzadas’ and the ‘Servicio General de Apoyo a la Investigación’ at ‘Universidad de Zaragoza’ for providing access to their instruments. We also thank Claudio Bonin from the ‘Instituto de Física del Litoral (CONICET-UNL)’ for performing the MOKE measurements. F B acknowledge financial support of the European Union under the REFRESH—Research Excellence For REgion Sustainability and High-tech Industries Project N∘ CZ.10.03.01/00/22/003/0000048 via the Operational Programme Just Transition and ENREGAT supported by MŠMT, Project N∘ LM2023056., Peer reviewed
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Enhancement of the spin Peltier effect in multilayers

  • Uchida, K.
  • Iguchi, R.
  • Daimon, S.
  • Ramos, R.
  • Anadón, A.
  • Lucas, I.
  • Algarabel, P.A.
  • Morellón, L.
  • Aguirre, M.H.
  • Ibarra, M.R.
  • Saitoh, E.
The spin Peltier effect (SPE), heat-current generation as a result of spin-current injection, has been investigated in alternately stacked Pt/Fe3O4 multilayer films. The temperature modulation induced by the SPE in the [Pt/Fe3O4] × n films was found to be significantly enhanced with increasing the number of Pt/Fe3O4 bilayers n. This SPE enhancement is much greater than that expected for a simple stack of independent Pt/Fe3O4 bilayers. The observed n dependence of the SPE can be explained by introducing spin-current redistribution in the multilayer films in the thickness direction, in a manner similar to the enhancement of the spin Seebeck effect in multilayers.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Spin Seebeck effect in Y-type hexagonal ferrite thin films

  • Hirschner, J.
  • Maryško, M.
  • Hejtmánek, J.
  • Uhrecký, R.
  • Soroka, M.
  • Buršík, J.
  • Anadón, A.
  • Aguirre, M.H.
  • KníŽek, K.
The longitudinal spin Seebeck effect (SSE) has been investigated using Pt/ferrite bilayers employing two Y-hexagonal ferrites Ba2Zn2Fe12O22 (Zn2Y) and Ba2Co2Fe12O22 (Co2Y) deposited by a spin-coating method on SrTiO3(111) substrates. The prepared hexagonal ferrites are highly oriented with c axes perpendicular to the substrate plane. The room-temperature magnetic moments of both ferrimagnetic ferrites amount to similar values and, most importantly, both have easy magnetization normal to the c axis. Despite their similar magnetic response the notable SSE signal is only observed for Zn2Y whereas the SSE signal of Co2Y is below the experimental noise level. A plausible explanation for this surprising discrepancy is magnetic disorder induced by cobalt cations, the random distribution of which in the Co2Y ferrite structure might critically limit the spin-wave propagation. This results in suppression of the SSE signal in Co2Y, while the Zn2Y with nonmagnetic substituent exhibits significant SSE signal. The temperature dependence of SSE for Zn2Y was measured over the 30-300-K range and quantitatively analyzed considering the heat flow through the Pt/Zn2Y bilayer and thermal gradient across the Zn2Y thin layer as the most relevant parameters. Using this approach the normalized SSE smoothly increases with lowering temperature, which correlates to increasing magnon propagation length and magnetization with decreasing temperature.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Tuning the interfacial charge, orbital, and spin polarization properties in La0.67Sr0.33MnO3/La1-xSrxMnO3 bilayers

  • Carreira, S.J.
  • Aguirre, M.H.
  • Briatico, J.
  • Weschke, E.
  • Steren, L.B.
The possibility of controlling the interfacial properties of artificial oxide heterostructures is still attracting researchers in the field of materials engineering. Here, we used surface sensitive techniques and high-resolution transmission electron microscopy to investigate the evolution of the surface spin-polarization and lattice strains across the interfaces between La0.66Sr0.33MnO3 thin films and low-doped manganites as capping layers. We have been able to fine tune the interfacial spin-polarization by changing the capping layer thickness and composition. The spin-polarization was found to be the highest at a critical capping thickness that depends on the Sr doping. We explain the non-trivial magnetic profile by the combined effect of two mechanisms: On the one hand, the extra carriers supplied by the low-doped manganites that tend to compensate the overdoped interface, favouring locally a ferromagnetic double-exchange coupling. On the other hand, the evolution from a tensile-strained structure of the inner layers to a compressed structure at the surface that changes gradually the orbital occupation and hybridization of the 3d-Mn orbitals, being detrimental for the spin polarization. The finding of an intrinsic spin-polarization at the A-site cation observed in x-ray magnetic circular dichroism (XMCD) measurements also reveals the existence of a complex magnetic configuration at the interface, different from the magnetic phases observed at the inner layers.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Interface-induced anomalous Nernst effect in Fe 3 O 4 /Pt-based heterostructures

  • Ramos, R.
  • Kikkawa, T.
  • Anadón, A.
  • Lucas, I.
  • Niizeki, T.
  • Uchida, K.
  • Algarabel, P.A.
  • Morellón, L.
  • Aguirre, M.H.
  • Ibarra, M.R.
  • Saitoh, E.
We have studied the anomalous Nernst effect (ANE) in [Fe 3 O 4 /Pt]-based heterostructures grown at high temperature, by measuring the ANE-induced electric field with a magnetic field applied normal to the sample surface, in the perpendicular magnetized configuration, where only the ANEs from the ferromagnetic layers or magnetic proximity effects can be detected. An ANE voltage is observed for [Fe 3 O 4 /Pt] n multilayers, and we further investigated its origin by performing measurements in [Fe 3 O 4 /Pt/Fe 3 O 4 ] trilayers as a function of the Pt thickness. Our results suggest the presence of an interface-induced ANE in the metallic layer, possibly driven by a heat induced subnanometer interdiffusion which affects the nature of the Fe 3 O 4 /Pt interface. Despite this ANE, the spin Seebeck effect is the dominant mechanism for the transverse thermoelectric voltage in the in-plane magnetized configuration, accounting for about 70% of the voltage in the multilayers.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Enhanced thermo-spin effects in iron-oxide/metal multilayers

  • Ramos, R.
  • Lucas, I.
  • Algarabel, P.A.
  • Morellón, L.
  • Uchida, K.
  • Saitoh, E.
  • Ibarra, M.R.
Since the discovery of the spin Seebeck effect (SSE), much attention has been devoted to the study of the interaction between heat, spin, and charge in magnetic systems. The SSE refers to the generation of a spin current upon the application of a thermal gradient and detected by means of the inverse spin Hall effect. Conversely, the spin Peltier effect (SPE) refers to the generation of a heat current as a result of a spin current induced by the spin Hall effect. Here we report a strong enhancement of both the SSE and SPE in Fe3O4/Pt multilayered thin films at room temperature as a result of an increased thermo-spin conversion efficiency in the multilayers. These results open the possibility to design thin film heterostructures that may boost the application of thermal spin currents in spintronics.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Apparent auxetic to non-auxetic crossover driven by Co 2+ redistribution in CoFe 2 O 4 thin films

  • Ferreiro-Vila, E.
  • Iglesias, L.
  • Lucas Del Pozo, I.
  • Varela-Dominguez, N.
  • Bui, C.T.
  • Rivas-Murias, B.
  • Vila-Fungueiriño, J.M.
  • Jimenez-Cavero, P.
  • Magen, C.
  • Morellon, L.
  • Pardo, V.
  • Rivadulla, F.
Oxide spinels of general formula AB2O4 (A = Mg2+, Fe2+; B = Al3+, Cr3+, etc.) constitute one of the most abundant crystalline structures in mineralogy. In this structure, cations distribute among octahedral and tetrahedral sites, according to their size and the crystal-field stabilization energy. The cationic arrangement determines the mechanical, magnetic, and transport properties of the spinel and can be influenced by external parameters like temperature, pressure, or epitaxial stress in the case of thin films. Here, we report a progressive change in the sign of the Poisson ratio, ¿, in thin films of CoFe2O4, defining a smooth crossover from auxetic (¿ < 0) to non-auxetic (¿ > 0) behavior in response to epitaxial stress and temperature. Microstructural and magnetization studies, as well as ab initio calculations, demonstrate that such unusual elastic response is actually due to a progressive redistribution of Co2+ among the octahedral and tetrahedral sites of the spinel structure. The results presented in this work clarify a long standing controversy about the magnetic and elastic properties of Co-ferrites and are of general applicability for understanding the stress-relaxation mechanism in complex crystalline structures.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Pulsed current-voltage electrodeposition of stoichiometric Bi2Te3 nanowires and their crystallographic characterization by transmission electron backscatter diffraction

  • Manzano, Cristina V.
  • Polyakov, Mikhail N.
  • Maiz, Jon
  • Aguirre Myriam H.
  • Maeder, Xavier
  • Martín-González, Marisol
Bi2Te3 nanowires with diameters ranging from 25 to 270 nm, ultra-high aspect ratio, and uniform growth front were fabricated by electrodeposition, pulsing between zero current density during the off time and constant potential during the on time (pulsed-current-voltage method, p-IV). The use of zero current density during the off time is to ensure no electrodeposition is carried out and the system is totally relaxed. By this procedure, stoichiometric nanowires oriented perpendicular to the c-axis is obtained for the different diameters of porous alumina templates. In addition, the samples show a uniform growth front with ultra-high aspect ratio single crystal nanowires. The high degree of crystallinity was verified by transmission electron backscatter diffraction. This characterization revealed that the nanowires present both large single crystalline areas and areas with alternating twin configurations.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Exploring tantalum as a potential dopant to promote the thermoelectric performance of zinc oxide

  • Arias-Serrano, Blanca I.
  • Xie, Wenjie
  • Aguirre, Myriam H.
  • Tobaldi, David M.
  • Sarabando, Artur R.
  • Rasekh, Shahed
  • Mikhalev, Sergey M.
  • Frade, Jorge R.
  • Weidenkaff, Anke
  • Kovalevsky, Andrei V.
Zinc oxide (ZnO) has being recognised as a potentially interesting thermoelectric material, allowing flexible tuning of the electrical properties by donor doping. This work focuses on the assessment of tantalum doping effects on the relevant structural, microstructural, optical and thermoelectric properties of ZnO. Processing of the samples with a nominal composition Zn1-xTaxO by conventional solid-state route results in limited solubility of Ta in the wurtzite structure. Electronic doping is accompanied by the formation of other defects and dislocations as a compensation mechanism and simultaneous segregation of ZnTa2O6 at the grain boundaries. Highly defective structure and partial blocking of the grain boundaries suppress the electrical transport, while the evolution of Seebeck coefficient and band gap suggest that the charge carrier concentration continuously increases from x = 0 to 0.008. Thermal conductivity is almost not affected by the tantalum content. The highest ZT~0.07 at 1175 K observed for Zn0.998Ta0.002O is mainly provided by high Seebeck coefficient (-464 µV/K) along with a moderate electrical conductivity of ~13 S/cm. The results suggest that tantalum may represent a suitable dopant for thermoelectric zinc oxide, but this requires the application of specific processing methods and compositional design to enhance the solubility of Ta in wurtzite lattice.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Effects of Zn Substitution in the Magnetic and Morphological Properties of Fe-Oxide-Based Core-Shell Nanoparticles Produced in a Single Chemical Synthesis

  • Lohr, J.
  • De Almeida, A.A.
  • Moreno, M.S.
  • Troiani, H.
  • Goya, G.F.
  • Torres Molina, T.E.
  • Fernandez-Pacheco, R.
  • Winkler, E.L.
  • Vasquez Mansilla, M.
  • Cohen, R.
  • Nagamine, L.C.C.M.
  • Rodríguez, L.M.
  • Fregenal, D.E.
  • Zysler, R.D.
  • Lima, E.
Magnetic, compositional, and morphological properties of Zn-Fe-oxide core-shell bimagnetic nanoparticles were studied for three samples with 0.00, 0.06, and 0.10 Zn/Fe ratios, as obtained from particle-induced X-ray emission analysis. The bimagnetic nanoparticles were produced in a one-step synthesis by the thermal decomposition of the respective acetylacetonates. The nanoparticles present an average particle size between 25 and 30 nm as inferred from transmission electron microscopy (TEM). High-resolution TEM images clearly show core-shell morphology for the particles in all samples. The core is composed by an antiferromagnetic (AFM) phase with a Wüstite (Fe1-yO) structure, whereas the shell is composed by a ZnxFe3-xO4 ferrimagnetic (FiM) spinel phase. Despite the low solubility of Zn in the Wüstite, electron energy-loss spectroscopy analysis indicates that Zn is distributed almost homogeneously in the whole nanoparticle. This result gives information on the formation mechanisms of the particle, indicating that the Wüstite is formed first, and the superficial oxidation results in the FiM ferrite phase with similar Zn concentration than the core. Magnetization and in-field Mössbauer spectroscopy of the Zn-richest nanoparticles indicate that the AFM phase is strongly coupled to the FiM structure of the ferrite shell, resulting in a bias field (HEB) appearing below TNFeO, with HEB values that depend on the core-shell relative proportion. Magnetic characterization also indicates a strong magnetic frustration for the samples with higher Zn concentration, even at low temperatures.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Nanoscale magnetic and charge anisotropies at manganite interfaces

  • Carreira, Santiago J
  • Aguirre, Myriam H
  • Briatico, Javier
  • Steren, Laura B.
Strong correlated manganites are still under intense research owing to their complex phase diagrams in terms of Sr-doping and their sensitivity to intrinsic and extrinsic structural deformations. Here, we performed X-ray absorption spectroscopy measurements of manganite bilayers to explore the effects that a local Sr-doping gradient produce on the charge and antiferromagnetic anisotropies. In order to gradually tune the Sr-doping level along the axis perpendicular to the samples we have grown a series of bilayers with different thicknesses of low-doped manganites (from 0 nm to 6 nm) deposited over a La0.7Sr0.3MnO3 metallic layer. This strategy permitted us to resolve with high accuracy the thickness region where the charge and spin anisotropies vary and the critical thickness tc over which the out of plane orbital asymmetry does not have any further modifications. We found that the antiferromagnetic spin axis points preferentially out of the sample plane regardless the capping layer thickness. However, it tilts partially into the sample plane far from this critical thickness, owing to the combined contributions of the external structural strain and electron doping. Furthermore, we found that the doping level of the capping layer strongly affects the critical thickness, giving clear evidence of the influence exerted by the electron doping on the orbital and magnetic configurations. These anisotropic changes induce subtle modifications on the domain reorientation of La0.7Sr0.3MnO3, as evidenced from the magnetic hysteresis cycles.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Interfacial ferromagnetism and atomic structures in high-temperature grown Fe3O4/Pt/Fe3O4 epitaxial trilayers

  • Kikkawa, T.
  • Suzuki, M.
  • Ramos, R.
  • Aguirre, M.H.
  • Okabayashi, J.
  • Uchida, K.
  • Lucas, I.
  • Anadón, A.
  • Kikuchi, D.
  • Algarabel, P.A.
  • Morellón, L.
  • Ibarra, M.R.
  • Saitoh, E.
Induced Pt ferromagnetism in Fe 3 O 4 / Pt / Fe 3 O 4 epitaxial trilayer films has been investigated by means of X-ray magnetic circular dichroism (XMCD) at the Pt L 3, 2-edges at various temperatures from 300 K to 12 K, including the metal-insulator transition temperature of Fe 3 O 4 (T V ~ 114 K). At all the temperatures, we observed clear XMCD signals due to Pt ferromagnetism, the amplitude of which was determined to be 0.39 µ B at 300 K and 0.52 µ B at 12 K for the sample with the Pt thickness of ~ 2 nm. Interestingly, these values are comparable to or even greater than those in Pt/3 d-ferromagnetic-metal (Fe, Ni, Co, and Ni 81 Fe 19) junction systems. The results can be interpreted in terms of a possible Fe interdiffusion into the Pt layer and also possible Fe-Pt alloying due to its high-temperature deposition.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Free-Radical Formation by the Peroxidase-Like Catalytic Activity of MFe2O4 (M = Fe, Ni, and Mn) Nanoparticles

  • Moreno Maldonado, Ana Carolina
  • Winkler, Elin L.
  • Raineri, Mariana
  • Toro Córdova, Alfonso
  • Rodríguez, Luis M.
  • Troiani, Horacio E.
  • Mojica Pisciotti, Mary Luz
  • Vasquez Mansilla, Marcelo
  • Tobia, Dina
  • Nadal, Marcela S.
  • Torres, Teobaldo E
  • De Biasi, Emilio
  • Ramos, Carlos A.
  • Goya, Gerardo F.
  • Zysler, Roberto D.
  • Lima, Enio
Ferrite magnetic nanoparticles (MNPs) have peroxidase-like activity and thus catalyze the decomposition of H2O2-producing reactive oxygen species (ROS). Increasingly important applications of these ferrite MNPs in biology and medicine require that their morphological, physicochemical, and magnetic properties need to be strictly controlled. Usually, the tuning of their magnetic properties is achieved by the replacement of Fe by other 3d metals, such as Mn or Ni. Here, we studied the catalytic activity of ferrite MNPs (MFe2O4, M = Fe2+/Fe3+, Ni, and Mn) with the mean diameter ranging from 10 to 12 nm. Peroxidase-like activity was studied by electron paramagnetic resonance (EPR) using the spin-trap 5, 5-dimethyl-1-pyrroline N-oxide at different pHs (4.8 and 7.4) and temperatures (25 and 40 °C). We identified an enhanced amount of hydroxyl (•OH) and perhydroxyl (•OOH) radicals for all samples, compared to a blank solution. Quantitative studies show that [•OH] is the dominant radical formed for Fe3O4, which is strongly reduced with the concomitant oxidation of Fe2+ or its substitution (Ni or Mn). A comparative analysis of the EPR data against in vitro production of ROS in microglial BV2 cell culture provided additional insights regarding the catalytic activity of ferrite MNPs, which should be considered if biomedical uses are intended. Our results contribute to a better understanding of the role played by different divalent ions in the catalytic activity of ferrite nanoparticles, which is very important because of their use in biomedical applications.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Room-Temperature AFM Electric-Field-Induced Topotactic Transformation between Perovskite and Brownmillerite SrFeOx with Sub-Micrometer Spatial Resolution

  • Ferreiro-Vila, E.
  • Blanco-Canosa, S.
  • Lucas del Pozo, I.
  • Vasili, H.B.
  • Magén, C.
  • Ibarra, A.
  • Rubio-Zuazo, J.
  • Castro, G.R.
  • Morellón, L.
  • Rivadulla, F.
Reversible structural transformations between perovskite (PV) ABO3- d and brownmillerite (BM) ABO2.5 (A = Ca2+, Sr2+; B = Fe4+/3, Co4+/3+) oxides can be induced by topotactic oxygen exchange at moderate temperatures under reducing/oxidizing conditions. The combination of a large oxide-ion conductivity and a small free energy difference between the 4+/3+ oxidation states of many 3d transition metal ions enables these topotactic transformations. Herein, it is demonstrated that the electric field produced by a voltage-biased atomic force microscopy tip can induce such transformation between PV SrFeO3- d and BM SrFeO2.5 at room temperature and with sub-micrometer spatial resolution. Interestingly, the structural transformation is kept after the electric field is removed, allowing a nonvolatile control of the local chemical, electrical, optical, and magnetic properties. Thus, the results presented in this paper open the door for the fabrication of stable ionic-based devices through the electric field patterning of different crystallographic phases.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Reduction of thermal conductivity in ferroelectric SrTiO3 thin films

  • Sarantopoulos, A.
  • Saha, D.
  • Ong, W.L.
  • Magen, C.
  • Malen, J.A.
  • Rivadulla, F.
Bulk SrTiO3 is a quantum paraelectric in which an antiferrodistortive distortion below approximate to 105 K and quantum fluctuations at low temperature preclude the stabilization of a long-range ferroelectric state. However, biaxial mechanical stress, impurity doping, and Sr nonstoichiometry, among other mechanisms, are able to stabilize a ferroelectric or relaxor ferroelectric state at room temperature, which develops into a longer-range ferroelectric state below 250 K. In this paper, we show that epitaxial SrTiO3 thin films grown under tensile strain on DyScO3 exhibit a large reduction of thermal conductivity, approximate to 60% of at room temperature, with respect to identical strain-free or compressed films. The thermal conductivity shows a further reduction below 250 K, a temperature concurrent with the peak in the dielectric constant [J. H. Haeni et al., Nature (London) 430, 758 (2004)]. These results suggest that strain gradients in the relaxor and ferroelectric phase of SrTiO3 are very effective phonon scatterers, limiting the thermal transport in this material.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Tunable resistivity exponents in the metallic phase of epitaxial nickelates

  • Guo, Qikai
  • Farokhipoor, Saeedeh
  • Magén, César
  • Rivadulla, Francisco
  • Noheda, Beatriz
We report a detailed analysis of the electrical resistivity exponent of thin films of NdNiO3 as a function of epitaxial strain. Thin films under low strain conditions show a linear dependence of the resistivity versus temperature, consistent with a classical Fermi gas ruled by electron-phonon interactions. In addition, the apparent temperature exponent, n, can be tuned with the epitaxial strain between n = 1 and n = 3. We discuss the critical role played by quenched random disorder in the value of n. Our work shows that the assignment of Fermi/Non-Fermi liquid behaviour based on experimentally obtained resistivity exponents requires an in-depth analysis of the degree of disorder in the material.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Strain-induced magnetic transition in CaMnO3 ultrathin films

  • Pedroso, A.L.
  • Barral, M.A.
  • Graf, M.E.
  • Llois, A.M.
  • Aguirre, M.H.
  • Steren, L.B.
  • Di Napoli, S.
The effect of high tensile strain and low dimensionality on the magnetic and electronic properties of CaMnO3 ultrathin films, epitaxially grown on SrTiO3 substrates, are experimentally studied and theoretically analyzed. By means of ab initio calculations, we find that both the high strain produced by the substrate and the presence of the free surface contribute to the stabilization of an in-plane ferromagnetic coupling, giving rise to a nonzero net magnetic moment in the ultrathin films. Coupled with this change in the magnetic order we find an insulatormetal transition triggered by the quantum confinement and the tensile epitaxial strain. Accordingly, our magnetic measurements in 3-nm ultrathin films show a ferromagnetic hysteresis loop, absent in the bulk compound due to its G-type antiferromagnetic structure.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Large memcapacitance and memristance at Nb:SrTiO3/La0.5Sr0.5Mn0.5Co0.5O3-d topotactic redox interface

  • Román Acevedo, W.
  • Van Den Bosch, C.A.M.
  • Aguirre, M.H.
  • Acha, C.
  • Cavallaro, A.
  • Ferreyra, C.
  • Sánchez, M.J.
  • Patrone, L.
  • Aguadero, A.
  • Rubi, D.
The possibility to develop neuromorphic computing devices able to mimic the extraordinary data processing capabilities of biological systems spurs the research on memristive systems. Memristors with additional functionalities such as robust memcapacitance can outperform standard devices in key aspects such as power consumption or miniaturization possibilities. In this work, we demonstrate a large memcapacitive response of a perovskite memristive interface, using the topotactic redox ability of La0.5Sr0.5Mn0.5Co0.5O3-d (LSMCO, 0 = d = 0.62). We demonstrate that the multi-mem behavior originates at the switchable n-p diode formed at the Nb:SrTiO3/LSMCO interface. We found for our Nb:SrTiO3/LSMCO/Pt devices a memcapacitive effect CHIGH/CLOW ~100 at 150 kHz. The proof-of-concept interface reported here opens a promising venue to use topotactic redox materials for disruptive nanoelectronics, with straightforward applications in neuromorphic computing technology.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Topotactic transformation in SrFeO3- d triggered by low-dose Ga+ focused ion irradiation

  • Ferreiro-Vila, Elías
  • Bugallo, David
  • Magén, César
  • Rivadulla, Francisco
  • De Teresa, José María
We introduce a single-step lithography process based on Ga+-focused ion beam (FIB) irradiation to trigger a topotactic transformation on SrFeO3-d thin films, from the perovskite to the brownmillerite (BM) crystal structure. The crystallographic transformation is triggered by preferential oxygen sputtering by Ga+-FIB irradiation, which favors the formation of the SrFeO2.5 BM phase. The transformation has been verified through micro-Raman spectroscopy on thin films subjected to Ga+-FIB irradiation under 5 kV and 30 kV. Inducing crystallographic transformations by FIB in a single-step process (without the need of resists), at a very high speed (low Ga+ doses are required, in the range of 1015 ions/cm2), with very high spatial resolution (limited by the ion beam spot, of a few square nanometers) and with potential for upscaling using broad Ga+ beams, this approach represents a significant forward step over previous methods using multistep lithographic or electrochemical procedures. All these virtues make this process appealing to develop applications based not only on SrFeO3-d thin films but also on other oxide films harnessing topotactic transformations.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Adjusting the Neel relaxation time of Fe3O4/ZnxCo1-xFe2O4 core/shell nanoparticles for optimal heat generation in magnetic hyperthermia

  • Fabris, F.
  • Lohr, J.
  • Lima, E.
  • de Almeida, A.A.
  • Troiani, H.E.
  • Rodriguez, L.M.
  • Mansilla, M.V.
  • Aguirre, M.H.
  • Goya, G.F.
  • Rinaldi, D.
  • Ghirri, A.
  • Peddis, D.
  • Fiorani, D.
  • Zysler, R.D.
  • De Biasi, E.
  • Winkler, E.L.
In this work it is shown a precise way to optimize the heat generation in high viscosity magnetic colloids, by adjusting the Neel relaxation time in core/shell bimagnetic nanoparticles, for magnetic fluid hyperthermia (MFH) applications. To pursue this goal, Fe3O4/ZnxCo1-xFe2O4 core/shell nanoparticles were synthesized with 8.5 nm mean core diameter, encapsulated in a shell of similar to 1.1 nm of thickness, where the Zn atomic ratio (Zn/(Zn + Co) at%) changes from 33 to 68 at%. The magnetic measurements are consistent with a rigid interface coupling between the core and shell phases, where the effective magnetic anisotropy systematically decreases when the Zn concentration increases, without a significant change of the saturation magnetization. Experiments of MFH of 0.1 wt% of these particles dispersed in water, in Dulbecco modified Eagles minimal essential medium, and a high viscosity butter oil, result in a large specific loss power (SLP), up to 150 W g(-1), when the experiments are performed at 571 kHz and 200 Oe. The SLP was optimized adjusting the shell composition, showing a maximum for intermediate Zn concentration. This study shows a way to maximize the heat generation in viscous media like cytosol, for those biomedical applications that require smaller particle sizes.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Magnetic hyperthermia experiments with magnetic nanoparticles in clarified butter oil and paraffin: A thermodynamic analysis

  • de Almeida, A.A.
  • de Biasi, E.
  • Mansilla, M.V.
  • Valdes, D.P.
  • Troiani, H.E.
  • Urretavizcaya, G.
  • Torres, T.E.
  • Rodríguez, L.M.
  • Fregenal, D.E.
  • Bernardi, G.C.
  • Winkler, E.L.
  • Goya, G.F.
  • Zysler, R.D.
  • Lima, E.Jr.
In specific power absorption models for magnetic fluid hyperthermia (MFH) experiments, the magnetic relaxation time of nanoparticles (NPs) is known to be a fundamental descriptor of the heating mechanisms. The relaxation time is mainly determined by the interplay between the magnetic properties of NPs and the rheological properties of NPs’ environment. Although the role of magnetism in MFH has been extensively studied, the thermal properties of the NP medium and their changes during MFH experiments have been underrated so far. Herein, we show that ZnxFe3-xO4 NPs dispersed through different media with phase transition in the temperature range of experiment as clarified butter oil (CBO) and paraffin. These systems show nonlinear behavior of the heating rate within the temperature range of MFH experiments. For CBO, a fast increase at ~306 K is associated with changes in the viscosity (¿(T)) and specific heat (cp(T)) of the medium at its melting temperature. This increment in the heating rate takes place around 318 K for paraffin. The magnetic and morphological characterization of NPs together with the observed agglomeration of NPs above 306 and 318 K for CBO and paraffin, respectively, indicate that the fast increase in MFH curves could not be associated with the change in the magnetic relaxation mechanism, with Neél relaxation being dominant. In fact, successive experimental runs performed up to temperatures below and above the CBO and paraffin melting points resulted in different MFH curves due to agglomeration of NPs driven by magnetic field inhomogeneity during the experiments. Our results highlight the relevance of the thermodynamic properties of the system NP-medium for an accurate measurement of the heating efficiency for in vitro and in vivo environments, where the thermal properties are largely variable within the temperature window of MFH experiments.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Tuning coherent-phonon heat transport in LaCoO3/SrTiO3 superlattices

  • Bugallo D.
  • Langenberg E.
  • Carbó-Argibay E.
  • Varela Dominguez N.
  • Fumega A.O.
  • Pardo V.
  • Lucas, I.
  • Morellón, L.
  • Rivadulla F.
Accessing the regime of coherent phonon propagation in nanostructures opens enormous possibilities to control the thermal conductivity in energy harvesting devices, phononic circuits, etc. In this paper we show that coherent phonons contribute substantially to the thermal conductivity of LaCoO3/SrTiO3 oxide superlattices, up to room temperature. We show that their contribution can be tuned through small variations of the superlattice periodicity, without changing the total superlattice thickness. Using this strategy, we tuned the thermal conductivity by 20% at room temperature. We also discuss the role of interface mixing and epitaxial relaxation as an extrinsic, material dependent key parameter for understanding the thermal conductivity of oxide superlattices. © 2021 The Authors. Published by American Chemical Society.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Magnetization reversal modes and coercive field dependence on perpendicular magnetic anisotropy in FePt thin films

  • Román, A.
  • López Pedroso, A.
  • Bouzehouane, K.
  • Gómez, J. E.
  • Butera, A.
  • Aguirre, M. H.
  • Soares, M. Medeiros
  • Garcia, C.
  • Steren, L. B.
The competition between shape and perpendicular magnetic anisotropies in magnetic thin films gives rise to unusual magnetic behaviors. In ferromagnetic thin films, the presence of an out-of-plane component of the magnetic anisotropy may induce a transition from planar to stripe-like magnetic domains above a critical thickness, $t_{\mathrm c}$. In this article, we present a detailed study of the magnetization switching mechanism in FePt thin films, where this phenomenon is observed. Using micromagnetic simulations and experiments, we found that below $t_{\mathrm c}$ the reversal mechanism is well described by the two-phase model while above this thickness the magnetization within each stripe reverses by coherent rotation. We also analyzed the out-of-plane component of the magnetic anisotropy and its temperature dependence, probing that substrate-induced strains are responsible for the abnormal coercive field behavior observed for FePt films with $t\gt t_{\mathrm c}$.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Magnetic transition and spin-polarized two-dimensional electron gas controlled by polarization switching in strained CaMnO3/BaTiO3

  • Di Napoli, S.
  • Román, A.
  • Llois, A. M.
  • Aguirre, M. H.
  • Steren, L. B.
  • Barral, M. A.
Ab initio calculations show the presence of a strong magnetoelectric interfacial coupling in a CaMnO 3 ultrathin film grown on a strained BaTiO 3 Ferroelectric film. This heterostructure presents a polarization driven magnetic transition from a G-type to an A-type antiferromagnetic structure. Together with this magnetic transition we find a metallic behavior at the interface between these two insulators, where the charge character of the carriers can be tuned from electrons to holes by switching the electric polarization direction of the ferroelectric film. Besides, the electron gas is spin polarized while the hole gas is not.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Structure of ZnxFe3-xO4 nanoparticles studied by neutron diffraction and its relation with their response in magnetic hyperthermia experiments

  • Lohr, J.
  • Tobia, D.
  • Torres, T. E.
  • Rodríguez, L.
  • Puente Orench, I.
  • Cuello, G. J.
  • Aguirre, M. H.
  • Campo, J.
  • Aurelio, G.
  • Lima, E.
The mixed zinc-ferrite spinel magnetic nanoparticles (MNPs) with the general formula ZnxFe3−xO4 are among the most extensively studied families of Fe oxides due to their interesting and diverse chemical, electronic, and magnetic properties. These systems offer the possibility of surface functionalization and possess high biocompatibility, making them highly attractive for applications in biomedicine, such as magnetic fluid hyperthermia (MFH). The efficiency of the MFH process relies on the magnetic, structural and morphological properties of the MNPs. The substitution with the Zn ion and the cationic distribution, as well as the synthesis process employed, have a direct impact on the final properties of these oxides. Therefore, it is essential to have tools that enable a comprehensive characterization of the system to assess its performance in MFH. In this study, we have synthesized four ZnxFe3−xO4 MNP systems using three different methods: two by thermal decomposition at high temperatures, one by co-precipitation, and another by co-precipitation followed by ball milling. We analyze the effect of these various synthesis processes on the magnetic and crystallographic properties, aiming to correlate them with the response of each system in MFH. Neutron diffraction data are employed to determine the cation site occupation and to investigate the correlation with the synthesis method. MFH measurements were conducted in media of diverse viscosities, revealing different values of specific loss power, thus demonstrating a clear dependence on the synthesis process and Zn content.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Strain-induced enhancement of spin pumping in Pt/YIG bilayers

  • Solis, Lara M.
  • Carreira, Santiago J.
  • Gómez, Javier
  • Butera, Alejandro
  • Abellán, María
  • García, Carlos
  • Bonetto, Fernando
  • Vavassori, Paolo
  • Briático, Javier
  • Steren, Laura B.
  • Aguirre, Myriam H.
Enhancing spin-to-charge (S→C) conversion efficiency remains a key challenge in spintronic materials research. In this work we investigate the effect of substrate-induced strains onto the S→C efficiency. On one hand, we analyze strains-induced magnetic anisotropies in yttrium iron garnet (Y3Fe5O12, YIG) by comparing the magnetic and structural properties of YIG films grown on Gd3Ga5O12 (GGG) and (CaGd)3(MgZrGa)5O12 (SGGG) substrates. Differences in lattice mismatch—YIG//GGG (η = −0.06%) and YIG//SGGG (η = −0.83%)—lead to out-of-plane tensile strains in the first case and unexpected compressive strain in the latter. On the other hand, we study the spin injection efficiency on Pt/YIG bilayers evaluated by the inverse spin Hall effect (ISHE). We find that the resulting perpendicular magnetic anisotropy in YIG//SGGG, while not dominant over shape anisotropy, correlates with enhanced ISHE signals as observed in spin pumping ferromagnetic resonance and spin Seebeck effect experiments. Strain engineering proves effective in enhancing S→C conversion, providing insight into the design of efficient spintronic devices.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Coexistence of volatile and nonvolatile memristive effects in phase-separated La0.5Ca0.5MnO3-based devices

  • Ramírez, G.A.
  • Román Acevedo, W.
  • Rengifo, M.
  • Núñez, J. M.
  • Aguirre, M.H.
  • Briático, J.
  • Rubi, D.
In this work, we have investigated the coexistence of volatile and nonvolatile memristive effects in epitaxial phase-separated La0.5Ca0.5MnO3 thin films. At low temperatures (50 K), we observed volatile resistive changes arising from self-heating effects in the vicinity of a metal-to-insulator transition. At higher temperatures (140 and 200 K), we measured a combination of volatile and nonvolatile effects arising from the synergy between self-heating effects and ferromagnetic-metallic phase growth induced by an external electrical field. The results reported here add phase separated manganites to the list of materials that can electrically mimic, on the same device, the behavior of both neurons and synapses, a feature that might be useful for the development of neuromorphic computing hardware.
Dipòsit Digital de Documents de la UAB
Publication Artículo científico (JournalArticle)

Ferroelectric Domain Walls in PbTiO3 Are Effective Regulators of Heat Flow at Room Temperature

  • Langenberg, Eric|||0000-0002-6944-4713
  • Saha, Dipanjan
  • Holtz, Megan E.
  • Wang, Jian-Jun
  • Bugallo, David|||0000-0002-5636-9267
  • Ferreiro-Vila, Elias|||0000-0002-2530-2414
  • Paik, Hanjong
  • Hanke, Isabelle
  • Ganschow, Steffen
  • Muller, David A.|||0000-0003-4129-0473
  • Chen, Long-Qing
  • Catalan, Gustau|||0000-0003-0214-4828
  • Domingo Marimon, Neus|||0000-0002-5229-6638
  • Malen, Jonathan|||0000-0003-4560-4476
  • Schlom, Darrell G.|||0000-0003-2493-6113
  • Rivadulla, Francisco|||0000-0003-3099-0159
Achieving efficient spatial modulation of phonon transmission is an essential step on the path to phononic circuits using "phonon currents". With their intrinsic and reconfigurable interfaces, domain walls (DWs), ferroelectrics are alluring candidates to be harnessed as dynamic heat modulators. This paper reports the thermal conductivity of single-crystal PbTiO thin films over a wide variety of epitaxial-strain-engineered ferroelectric domain configurations. The phonon transport is proved to be strongly affected by the density and type of DWs, achieving a 61% reduction of the roomerature thermal conductivity compared to the single-domain scenario. The thermal resistance across the ferroelectric DWs is obtained, revealing a very high value (≈5.0 × 10 K m W), comparable to grain boundaries in oxides, explaining the strong modulation of the thermal conductivity in PbTiO. This low thermal conductance of the DWs is ascribed to the structural mismatch and polarization gradient found between the different types of domains in the PbTiO films, resulting in a structural inhomogeneity that extends several unit cells around the DWs. These findings demonstrate the potential of ferroelectric DWs as efficient regulators of heat flow in one single material, overcoming the complexity of multilayers systems and the uncontrolled distribution of grain boundaries, paving the way for applications in phononics.
Dipòsit Digital de Documents de la UAB
Publication Artículo científico (JournalArticle)

Large thermoelectric power variations in epitaxial thin films of layered perovskite GdBaCo2O5.5±δwith a different preferred orientation and strain

  • Chatterjee, Arindom|||0000-0002-0861-2058
  • Chávez Ángel, Emigdio|||0000-0002-9783-0806
  • Ballesteros, Belén|||0000-0002-1958-8911
  • Caicedo Roque, Jose Manuel|||0000-0002-5192-4989
  • Padilla-Pantoja, Jessica|||0000-0002-7769-7753
  • Leborán, Víctor|||0000-0001-9806-3234
  • Sotomayor Torres, Clivia M.|||0000-0001-9986-2716
  • Rivadulla, Francisco|||0000-0003-3099-0159
  • Santiso, José|||0000-0003-4274-2101
This work describes the growth of thin epitaxial films of the layered perovskite material GdBaCoO(GBCO) on different single crystal substrates SrTiO(STO), (LaAlO)(SrTaAlO)(LSAT) and LaAlO(LAO) as an approach to study changes in the thermoelectric properties by means of the induced epitaxial strain. In addition to strain changes, the films grow with considerably different preferred orientations and domain microstructures: GBCO films on STO are purelyc-axis oriented (c) with an average 0.18% in-plane tensile strain; GBCO on LSAT is composed of domains with a mixed orientation (candc) with an average 0.71% in-plane compressive strain; while on LAO it isb-axis oriented (c) with an average 0.89% in-plane compressive strain. These differences result in important cell volume changes, as well as in the orthorhombicity of thea-bplane of the GBCO structure, which in turn induce a change in the sign and temperature dependence of the thermopower, while the electrical conductivity remains almost unchanged. In general, compressively strained films show negativeSthermopower (n-type) while tensile strained films show a positiveS(p-type) at low temperatures, probing the adaptive nature of the GdBaCoOcompound. These results point to the spontaneous generation of oxygen vacancies to partially accommodate the epitaxial stress as the main cause for this effect.
Dipòsit Digital de Documents de la UAB
Publication Artículo científico (JournalArticle)

Deconvolution of Phonon Scattering by Ferroelectric Domain Walls and Point Defects in a PbTiO3Thin Film Deposited in a Composition-Spread Geometry

  • Bugallo, David|||0000-0002-5636-9267
  • Langenberg, Eric|||0000-0002-6944-4713
  • Ferreiro-Vila, Elias|||0000-0002-2530-2414
  • Smith, Eva H.
  • Stefani, Christina|||0000-0002-8818-075X
  • Batlle, Xavier|||0000-0001-7897-2692
  • Catalan, Gustau|||0000-0003-0214-4828
  • Domingo Marimon, Neus|||0000-0002-5229-6638
  • Schlom, Darrell G.|||0000-0003-2493-6113
  • Rivadulla, Francisco|||0000-0003-3099-0159
We present a detailed analysis of the temperature dependence of the thermal conductivity of a ferroelectric PbTiO3 thin film deposited in a composition-spread geometry enabling a continuous range of compositions from ∼25% titanium deficient to ∼20% titanium rich to be studied. By fitting the experimental results to the Debye model we deconvolute and quantify the two main phonon-scattering sources in the system: ferroelectric domain walls (DWs) and point defects. Our results prove that ferroelectric DWs are the main agent limiting the thermal conductivity in this system, not only in the stoichiometric region of the thin film ([Pb]/[Ti] ≈ 1) but also when the concentration of the cation point defects is significant (up to ∼15%). Hence, DWs in ferroelectric materials are a source of phonon scattering at least as effective as point defects. Our results demonstrate the viability and effectiveness of using reconfigurable DWs to control the thermal conductivity in solid-state devices.