Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 42
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Magnetic and electrical properties of single-phase multiferroic (1-x)Pb(Zr0.52Ti0.48)O3–xPb(Fe0.5Nb0.5)O3 thin films prepared by sol-gel route

  • Imhoff, L.
  • Román, Augusto
  • Barolin, S. A.
  • Pellegri, Nora S.
  • Steren, Laura B.
  • Aguirre, Myriam H.
  • Stachiotti, Marcelo G.
Single-phase multiferroic (1-x)Pb(Zr0.52Ti0.48)O3-xPb(Fe0.5Nb0.5)O3 (0≤x≤0.5) thin films were synthesized by sol-gel route and characterized to understand their structural, electrical, and magnetic properties. The films were thermally treated by conventional furnace (CFA) and rapid thermal annealing (RTA). A pyrochlore-free perovskite phase is stabilized only by RTA in samples with high Fe3+/Nb5+ content. The films displayed excellent dielectric and ferroelectric properties in the whole concentration range, with saturated hysteresis loops and remanent polarization values of ∼15μC/cm2. Films with x>0.3 showed ferromagnetic behavior at room temperature. Consequently, the multiferroic behavior in the films occurs in a different concentration range than that observed in bulk ceramics. The origin of the weak ferromagnetism is discussed., The authors thank Consejo Nacional de Investigaciones Científicas y Técnicas (CONICET) for financial support. M.G.S thanks support from CIUNR and L.B.S from FONCYT PICT2014-1047. We also acknowledge the financial support of H2020-MSCA-RISE-2020 MELON Grant No. 872631 and the access to TEM equipment at LMA- University of Zaragoza to perform TEM studies., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Optimization of the multi-mem response of topotactic redox La1/2Sr1/2Mn1/2Co1/2O3- x

  • Román Acevedo, Wilson
  • Aguirre, Myriam H.
  • Ferreyra, C.
  • Sánchez, M. J.
  • Rengifo, Miguel
  • Bosch, C. A. M. van den
  • Aguadero, A.
  • Noheda, Beatriz
  • Rubi, Diego
Memristive systems emerge as strong candidates for the implementation of resistive random access memories and neuromorphic computing devices, as they can mimic the electrical analog behavior or biological synapses. In addition, complementary functionalities, such as memcapacitance, could significantly improve the performance of bio-inspired devices in key issues, such as energy consumption. However, the physics of mem systems is not fully understood so far, hampering their large-scale implementation in devices. Perovskites that undergo topotactic transitions and redox reactions show improved performance as mem systems, compared to standard perovskites. In this paper, we analyze different strategies to optimize the multi-mem behavior (memristive and memcapacitive) of topotactic redox La1/2Sr1/2Mn1/2Co1/2O3−x (LSMCO) films grown on Nb:SrTiO3. We explored devices with different crystallinities (from amorphous to epitaxial LSMCO), out-of-plane orientation [(001) and (110)], and stimulated either with voltage or current pulses. We found that an optimum memory response is found for epitaxial (110) LSMCO stimulated with current pulses. Under these conditions, the system efficiently exchanges oxygen with the environment minimizing, at the same time, self-heating effects that trigger nanostructural and chemical changes that could affect the device integrity and performance. Our work contributes to pave the way for the integration of multi-mem topotactic redox oxide-based interfaces in multiple device architectures, in order to exploit their memristive and memcapacitive properties for data storage or neuromorphic computation., The authors acknowledge support from the UNCuyo (Grant No. 06/C591), the ANPCyT (Grant Nos. PICT2017-1836, PICT2019-02781, and PICT2019-0654), and the EU-H2020-RISE project “MELON” (Grant No. 872631). This publication is part of the project “Memcapacitive elements for cognitive devices” (Project No. 040.11.735), which is financed by the Dutch Research Council (NWO). The authors acknowledge support from the Ministry of Science and Higher Education of the RF (State Contract No. N13.2251.21.0042). B.N. acknowledges financial support of the CogniGron research center and the Ubbo Emmius Funds (University of Groningen)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Epitaxial ferroelectric memristors integrated with silicon

  • Rengifo, Miguel
  • Aguirre, Myriam H.
  • Sirena, Martín
  • Lüders, Ulrike
  • Rubi, Diego
Neuromorphic computing requires the development of solid-state units able to electrically mimic the behavior of biological neurons and synapses. This can be achieved by developing memristive systems based on ferroelectric oxides. In this work we fabricate and characterize high quality epitaxial BaTiO3-based memristors integrated with silicon. After proving the ferroelectric character of BaTiO3 we tested the memristive response of LaNiO3/BaTiO3/Pt microstructures and found a complex behavior which includes the co-existence of volatile and non-volatile effects, arising from the modulation of the BaTiO3/Pt Schottky interface by the direction of the polarization coupled to oxygen vacancy electromigration to/from the interface. This produces remanent resistance loops with tunable ON/OFF ratio and asymmetric resistance relaxations. These properties might be harnessed for the development of neuromorphic hardware compatible with existing silicon-based technology., We acknowledge Marten Piantek, from LMA-INA-UNIZAR, for the PFM measurements. We acknowledge support from ANPCyT (PICT 2019-02781, PICT2020A-00415) and EU-H2020-RISE project MELON (Grant No. 872631)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Oxygen vacancy dynamics in Pt/TiOx/TaOy/Pt memristors: exchange with the environment and internal electromigration

  • Leal Martir, Rodrigo
  • Sánchez, M. J.
  • Aguirre, Myriam H.
  • Quiñonez, Walter
  • Ferreyra, C.
  • Acha, C.
  • Lecourt, J.
  • Lüders, Ulrike
  • Rubi, Diego
Memristors are expected to be one of the key building blocks for the development of new bio-inspired nanoelectronics. Memristive effects in transition metal oxides are usually linked to the electromigration at the nanoscale of charged oxygen vacancies (OV). In this paper we address, for Pt/TiOx/TaOy/Pt devices, the exchange of OV between the device and the environment upon the application of electrical stress. From a combination of experiments and theoretical simulations we determine that both TiOx and TaOy layers oxidize, via environmental oxygen uptake, during the electroforming process. Once the memristive effect is stabilized (post-forming behavior) our results suggest that oxygen exchange with the environment is suppressed and the OV dynamics that drives the memristive behavior is restricted to an internal electromigration between TiOx and TaOy layers. Our work provides relevant information for the design of reliable binary oxide memristive devices., We acknowledge support from UNCuyo (06/C591), ANPCyT (PICT2017-1836, PICT2019-02781, PICT2019-0654 and PICT2020A-00415) and EU-H2020-RISE project 'MELON' (Grant No. 872 631)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Coexistence of volatile and nonvolatile memristive effects in phase-separated La0.5Ca0.5MnO3-based devices

  • Ramírez, Gerardo
  • Román Acevedo, Wilson
  • Rengifo, Miguel
  • Nuñez, Jorge M.
  • Aguirre, Myriam H.
  • Briático, Javier
  • Rubi, Diego
In this work, we have investigated the coexistence of volatile and nonvolatile memristive effects in epitaxial phase-separated La0.5Ca0.5MnO3 thin films. At low temperatures (50 K), we observed volatile resistive changes arising from self-heating effects in the vicinity of a metal-to-insulator transition. At higher temperatures (140 and 200 K), we measured a combination of volatile and nonvolatile effects arising from the synergy between self-heating effects and ferromagnetic-metallic phase growth induced by an external electrical field. The results reported here add phase separated manganites to the list of materials that can electrically mimic, on the same device, the behavior of both neurons and synapses, a feature that might be useful for the development of neuromorphic computing hardware., We acknowledge support from ANPCyT (Nos. PICT2019-02781 and PICT2020A-00415), EU-H2020-RISE projects MELON (Grant No. 872631), and SPICOLOST (Grant No. 734187)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Efficient generation of highly crystalline carbon quantum dots via electrooxidation of ethanol for rapid photodegradation of organic dyes

  • Barrionuevo, Santiago D.
  • Fioravanti, Federico
  • Nuñez, Jorge M.
  • Llaver, Mauricio
  • Aguirre, Myriam H.
  • Bellino, Martin G.
  • Lacconi, Gabriela I.
  • Ibañez, Francisco J.
This article is part of the themed collection: #MyFirstJMCC, Achieving versatile routes to generate crystalline carbon-based nanostructures has become a fervent pursuit in photocatalysis-related fields. We demonstrate that the direct electrooxidation of ethanol, performed on Ni foam, yields ultra-small and highly crystalline graphene-like structures named carbon quantum dots (CQDs). We perform simulations of various sp2 and sp3 domains in order to understand the optical properties of CQDs by accounting their contribution as absorbance/luminescent centers in the overall optical response. Experiments and simulations reveal that absorbance bands for as-synthesized CQDs are dominated by small sp2 domains comprised of ≤7 aromatic-rings. After 48 h synthesis, the dispersion transition from yellow to red, exhibiting new and red shifted absorbance bands. Furthermore, fluorescence emission is governed by medium-sized sp2 domains (with aromatic ring counts ≤12) and oxygen-containing groups. These oxygen-rich groups within the CQDs, confirmed by FT-IR and XPS, are responsible for the fast photodegradation of organic dyes, with ∼90% of methylene blue (MB) being degraded within the first 5 min of light exposure. Our work provides crucial insights about the electrochemical synthesis and overall optical properties of carbon nanostructures, while being effective and reliable toward the degradation of contaminants in water., We gratefully acknowledge financial support from PICT (2019–2188) and Proyecto de Incentivos 2019-X-887 from UNLP. SB and FF acknowledge CONICET for their doctoral scholarships. We also acknowledge the financial support of European Commission through Marie Skłodowska-Curie Actions H2020 RISE with the projects MELON (grant no. 872631) and ULTIMATE-I (grant no. 101007825). Authors would like to acknowledge the access of equipment of “Servicio General de Apoyo a la Investigación (SAI), Universidad de Zaragoza” and LAMARX-SNM at Universidad Nacional de Córdoba (UNC), Argentina., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Novel Ir1–xCoxO2 thin films: Growth and characterization

  • Laguna-Marco, M. A.
  • Herrero-Albillos, Julia
  • Aguirre, Myriam H.
  • Rueda-Jiménez, Marcos
  • Mikulska, Iuliia
Ir1–xCoxO2 thin films have been prepared by reactive co–sputtering deposition at room temperature. Composition, structure, electronic properties and electric and magnetic behavior have been analyzed by different techniques including XRR, XRD, TEM microscopy, SQUID magnetometry, electrical resistivity and XAS spectroscopy. After annealing, an Ir1–xCoxO2 substitutional solid solution phase with rutile crystal structure was achieved for a wide Co-doping range 0 ≤ x ≤ 0.6. Starkly departing from the highly insulating behavior of CoO and Co3O4, the electrical resistivity at room temperature of our films is only slightly higher than that of IrO2. Likewise, our work shows that the magnetic response of the doped films is very similar to that of the paramagnetic parent IrO2. Neither ferromagnetism nor enhanced paramagnetism is observed. XAS spectra indicate a Co3+ oxidation state and, correspondingly, an oxidation state of ∼5+ for Ir ions in the polycrystalline Ir0.6Co0.4O2 film. By application of sum rules, a 13 % increase in the spin–orbit coupling is found despite the lattice shrinkage causes a detrimental bandwidth broadening., This work was supported by Project PID2020-115159GB-I00 funded by Spanish MCIN/AEI/10.13039/501100011033 and by the Regional Government of Aragon (Grant No. E12-23R RASMIA). We acknowledge Diamond Light Source for time on B18 under Proposal SP-32410. The research leading to this result has been supported by the project CALIPSOplus under the Grant Agreement 730872 from the EU Framework Programme for Research and Innovation HORIZON 2020. The authors also gratefully acknowledge the European Commission for the financial support under the H2020-MSCA-RISE-2020 MELON project Nº 872631 and H2020-MSCA-RISE-2021 ULTIMATE-I project Nº 101007825., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Research data Set de datos (Dataset)

Data for Novel Ir1–xCoxO2 thin films: growth and characterization

  • Laguna-Marco, M. A.
  • Herrero-Albillos, Julia
  • Aguirre, Myriam H.
  • Rueda-Jiménez, Marcos
  • Mikulska, Iuliia
  • Proyecto: PID2020-115159GB-I00
[Ir1–xCoxO2 thin films were prepared by reactive magnetron co–sputtering deposition on Si substrates at room temperature (RT) from metallic Ir and Co targets. Crystal structures were characterized by powder X-ray diffraction (XRD) at room temperature in a Rigaku D-Max system using Cu Kalpha wavelength. The resistivity measurements were carried out in a PPMS-9T. The magnetic measurements were carried out in a SQUID magnetometer MPMS–XL (both from Quantum Design). Transmission electron microscopy images, HRTEM (High resolution transmission electron microscopy) and STEM-HAADF (scanning TEM with high angular annular dark field detector), were performed by Tecnai F30 and Titan G2 80-300 keV (with aberration corrected probe), respectively, operated at 300 keV. The compositional analysis profile was performed by energy dispersive spectroscopy (EDS) in an Oxford Aztec equipment in situ STEM-HAADF analysis. The lamellae for TEM analysis were prepared by focused ion beam in a commertial Helios 650 N dual beam equipment. X–ray absorption spectroscopy (XAS) measurements were carried out at the B18 beamline of the Diamond Light Source. Co K-edge and Ir L2,3-edge XAS spectra of the films were measured in fluorescence mode using Quick-EXAFS technique. A Si (111) double crystal monochromator was used to select the incident X-ray energy. Co K-edge (Ir L3-edge) measurements have been performed using collimating mirror with Pt (Cr) coating. The fluorescence measurements have been performed using Canberra 36-pixel Monolithic Segmented Hyper Pure Germanium Detector with the STFC Xspress4 Digital Pulse Processor.], Spanish MICINN Project No. PID2020-115159GBI00/AEI/10.13039/501100011033; Regional Government of Aragon (Grant No. E12-23R RASMIA); European Commission under the H2020-MSCA-RISE-2020 MELON project Nº 872631 and H2020-MSCA-RISE-2021 ULTIMATE-I project Nº 101007825., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Sol-gel synthesis and multiferroic properties of pyrochlore-free Pb(Fe0.5Nb0.5)O3 thin films

  • Imhoff, L.
  • Di Marco, M. B.
  • Barolin, S. A.
  • Rengifo, Miguel
  • Aguirre, Myriam H.
  • Stachiotti, Marcelo G.
Lead iron niobate (PbFe0.5Nb0.5O3 – PFN) thin films were synthesized by a modified sol-gel route, which offers the advantage of a rapid, simple and non-toxic reaction method. Polycrystalline perovskite-structured PFN thin films without pyrochlore phases were obtained on Pt/Ti/SiO2/Si substrates after sintering by rapid thermal annealing at 650 °C. TEM and AFM images confirmed the excellent quality of the sintered film, while EDS spectroscopy revealed the presence of oxygen vacancies near the film/substrate interface. Electric measurements show good dielectric properties and ferroelectric behavior, characterized by typical C–V curves and well-defined P-E ferroelectric loops at 1 kHz, with remanent polarization values of ∼12 μC/cm2. The polarization, however, increases with decreasing frequency, indicating the presence of leakage currents. I–V measurements show a significant increase in DC-conduction at relatively low fields (around 100 kV/cm). The films display ferromagnetic behavior at room temperature, with magnetic remanence around 30 emu/cm3 and a coercive field of 1 kOe. These values are significantly higher than those obtained for PFN powders fabricated by the same sol-gel route, as well as the magnetization values reported in the literature for epitaxial films., This work was supported by Consejo Nacional de Investigaciones Científicas y Técnicas de la República Argentina (CONICET) by PIP Nº 0374. M.G.S. thanks support from Consejo de Investigaciones de la Universidad Nacional de Rosario (CIUNR). We acknowledge the financial support of the European Commission by the H2020-MSCA RISE projects MELON (Grant Nº 872631) and ULTIMATE-I (Grant Nº 101007825)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Stacking-configuration-preserved graphene quantum dots electrochemically obtained from CVD graphene

  • Barrionuevo, Santiago D.
  • Fioravanti, Federico
  • Nuñez, Jorge M.
  • Muñeton Arboleda, David
  • Lacconi, Gabriela I.
  • Bellino, Martin G.
  • Aguirre, Myriam H.
  • Ibañez, Francisco J.
The layer stacking morphology in nanocarbons is paramount for achieving new properties and outperforming applications. Here, we demonstrate that graphene quantum dots (GQDs) retain crystallinity and a stacking structure from CVD graphene grown on Ni foam. Our results reveal that GQD subdomains comprise a few-layer graphene structure in the AB···AB and ABC···ABC stacking configuration. HR-TEM images along with a multiple-approach characterization (XRD, XPS, UV–vis, AFM, and ATR-IR) exhibit ∼3.0 to ∼8.0 nm crystalline GQDs with 2–6 graphene layers thick indicating a disk-shape structure. The UV–vis profiles show changes in color of the dispersion (from colorless to red) during and after the electrochemistry, suggesting a systematic electrooxidation of graphene into smaller, highly crystalline, and more complex sp2/sp3 structures. Importantly, a control experiment performed under the same conditions but with a graphitic rod exhibited large, polydisperse, and multilayer carbon structures. This work demonstrates a relatively easy electrochemical synthesis to obtain GQDs which retain the pristine and, in turn, distinctive structure of graphene grown on Ni foam., We gratefully acknowledge financial support from PICT (2019-2188), PIP-2022-2024 0001 (CONICET), and Proyecto de Incentivos 2019-X-887 from UNLP. We also acknowledge the financial support of the European Commission through Marie Skłodowska-Curie Actions H2020 RISE with the projects MELON (Grant No. 872631) and ULTIMATE-I (Grant No. 101007825). The authors would like to acknowledge the access to the equipment of “Servicio General de Apoyo a la Investigación (SAI), Universidad de Zaragoza”. F.J.I. acknowledges Dr. Mauricio Llaver for the discussion on FT-IR spectrum of GQDs. S.D.B. and F.F. acknowledge CONICET for their doctoral scholarships., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Magnetic transition and spin-polarized two-dimensional electron gas controlled by polarization switching in strained CaMnO3/BaTiO3 slabs

  • Di Napoli, Solange
  • Román, Augusto
  • Llois, A. M.
  • Aguirre, Myriam H.
  • Steren, Laura B.
  • Barral, M. A.
𝐴⁢𝑏𝑖⁢𝑛⁢𝑖⁢𝑡⁢𝑖⁢𝑜 calculations show the presence of a strong magnetoelectric interfacial coupling in a CaMnO3 ultrathin film grown on a strained BaTiO3 ferroelectric film. This heterostructure presents a polarization driven magnetic transition from a G-type to an A-type antiferromagnetic structure. Together with this magnetic transition we find a metallic behavior at the interface between these two insulators, where the charge character of the carriers can be tuned from electrons to holes by switching the electric polarization direction of the ferroelectric film. Besides, the electron gas is spin polarized while the hole gas is not., This work was partially supported by PICT-2016-0867 and PICT-2019-2128 of the ANPCyT, Argentina, and by H2020-MSCA-RISE-2016 SPICOLOST Project No. 734187. We also acknowledge the financial support of European Commission through Marie Skłodowska-Curie Actions H2020 RISE with the projects MELON (Grant No. 872631) and ULTIMATE-I (Grant No. 101007825). Authors would like to acknowledge the access of equipment of “Servicio General de Apoyo a la Investigación (SAI), Universidad de Zaragoza.”, Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Effects of silver nanoparticle doping on electrical, optical, and photovoltaic properties of PbZrxTi1−xO3 thin films synthesized by sol–gel

  • Di Marco, M. B.
  • Imhoff, L.
  • Roldán, M. V.
  • Santiago, M. L.
  • Aguirre, Myriam H.
  • Pellegri, Nora S.
  • Stachiotti, Marcelo G.
The effects produced by the incorporation of silver nanoparticles (Ag-NPs) of an average size of ∼4 nm on the electrical, optical, and photovoltaic properties of PbZr0.52Ti0.48O3 (PZT) thin films are investigated. The films were synthesized by a chemical solution deposition process, and two different distributions of nanoparticles in the PZT matrix were tested: (1) alternated Ag-NPs and PZT layers, and (2) distributed Ag-NPs over the entire film volume. The resulting films, with thicknesses between 200 and 270 nm, display no segregation of secondary phases, and good dielectric and ferroelectric properties. An increase in remnant polarization is observed when the Ag-NPs are distributed over the volume, which is ascribed to the modification of the film texture. The incorporation of Ag-NPs into the PZT matrix produces an enhancement of the photocurrent density under UV illumination of ∼30%., This work was supported by Consejo Nacional de Investigaciones Científicas y Técnicas de la República Argentina (CONICET) by PIP No 0374 and No 0479. We acknowledge the financial support of the European Commission by the H2020-MSCA RISE projects MELON (Grant No 872631) and ULTIMATE-I (Grant No 101007825). M.G.S. thanks support from Consejo de Investigaciones de la Universidad Nacional de Rosario (CIUNR). The authors would like to acknowledge the access of equipment of “Servicio General de Apoyo a la Investigación (SAI), Universidad de Zaragoza”., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Fluorescent graphene quantum dots-enhanced machine learning for the accurate detection and quantification of Hg2+ and Fe3+ in real water samples

  • Llaver, Mauricio
  • Barrionuevo, Santiago D.
  • Nuñez, Jorge M.
  • Chapana, Agostina L.
  • Wuilloud, Rodolfo G.
  • Aguirre, Myriam H.
  • Ibañez, Francisco J.
Selective, accurate, fast detection with minimal usage of instrumentation has become paramount nowadays in the areas of environmental monitoring. Herein, we chemically modified fluorescent graphene quantum dots (GQDs) and trained a machine learning (ML) algorithm for the selective quantification of Hg2+ and Fe3+ ions present in real water samples. The probe is obtained via the electrosynthesis of CVD graphene in the presence of urea, followed by functionalization with 1-nitroso-2-naphthol (NN). The functionalization with NN moieties dramatically improves the selectivity and sensitivity of the probe toward Hg2+ and Fe3+, as demonstrated by LODs of 0.001 and 0.003 mg L−1, respectively. Simulations performed by time-dependent density functional theory (TD-DFT) reveals that the NN molecules within the GQDs are responsible for the florescence emission of the probe. The emission spectra profiles exhibited distinct characteristics between Hg2+ and Fe3+, enabling the ML model to precisely quantify and differentiate between both analytes present in natural and drinking waters. The ML results were further validated by measurements via cold vapor-atomic fluorescence spectroscopy and UV–vis spectroscopy. Our work demonstrates how chemical modification of GQDs, guided by an efficient ML model, markedly enhances sensitivity and selectivity in detecting harmful ions while critically reducing experiments and instrument handling., This research was funded by Consejo Nacional de Investigaciones Científicas y Técnicas (CONICET) (PIP-2022-2024-0001), Agencia Nacional de Promoción Científica y Tecnológica (FONCYT) (Projects PICT-2019-03859-BID, PICT-2019-2188-BID) and Universidad Nacional de Cuyo (Project 06/M035-T1) and UNLP (Project X-887) (Argentina). We acknowledge Federico Fioravanti and Dr. Gabriela I. Lacconi, from the Instituto de Investigaciones en Fisicoquimica de Córdoba (INFIQC, CONICET/UNC), for their help obtaining and analyzing the XPS spectra. We also acknowledge the financial support of European Commission with the action H2020 RISE projects MELON (Grant No. 872631) and ULTIMATE-I (Grant No. 101007825). Authors would like to acknowledge the use of “Servicio General de Apoyo a la Investigación-SAI, Universidad de Zaragoza”., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Multi-mem behavior at reduced voltages in La1/2Sr1/2Mn1/2Co1/2 O3-x perovskite modified with Sm: Ce O2

  • Román Acevedo, Wilson
  • Aguirre, Myriam H.
  • Noheda, Beatriz
  • Rubi, Diego
The use of machine learning algorithms is exponentially growing and concerns are being raised about their sustainability. Neuromorphic computing aims to mimic the architecture and the information processing mechanisms of the mammalian brain, appearing as the only avenue that offers significant energy savings compared to the standard digital computers. Memcapacitive devices, which can change their capacitance between different nonvolatile states upon the application of electrical stimulation, can significantly reduce the energy consumption of bio-inspired circuitry. In the present work, we study the multi-mem (memristive and memcapacitive) behavior of devices based on thin films of the topotactic redox L⁢a1/2⁢S⁢r1/2⁢M⁢n1/2⁢C⁢o1/2⁢O3−𝑥 (LSMCO) perovskite modified with Sm:Ce⁢O2 (SCO), grown on Nb:SrTiO3 with (001) and (110) out-of-plane orientations. Either the self-assembling at the nanoscale of both LSMCO and SCO phases or the doping with Ce(Sm) of the LSMCO perovskite were observed for different fabrication conditions and out-of-plane orientations. The impact of these changes on the device electrical behavior was determined. The optimum devices resulted those with (110) orientation and Ce(Sm) doping the perovskite. These devices displayed a multi-mem behavior with robust memcapacitance and significantly lower operation voltages (especially the reset voltage) in comparison with devices based on pristine LSMCO. In addition, they were able to endure electrical cycling—and the concomitant perovskite topotactic redox transition between oxidized and reduced phases—without suffering nanostructural changes nor cationic segregation. We link these properties to an enhanced perovskite reducibility upon Ce(Sm) doping. Our work contributes to increasing the reliability of LSMCO-based multi-mem systems and to reducing their operating voltages closer to the 1 V threshold, which are key issues for the development of nanodevices for neuromorphic or in-memory computing., We acknowledge support from ANPCyT (PICT2019-02781 and PICT2020A-00415) and EU-H2020-RISE project MELON (Grant No. 872631). This publication is also a result of the project “Memcapacitive elements for cognitive devices,” Project No. 040.11.735, which was financed by the Dutch Research Council (NWO)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Phase relations in the Nd2O3-Fe2O3 system: Structure and magnetic properties of perovskite NdFeO3 ceramics

  • Chudinovych, Olga V.
  • Vedel, Dmytro V.
  • Stasyuk, Oleksandr O.
  • Samelyuk, Anatoly V.
  • Aguirre, Myriam H.
The phase relations in the Nd2O3-Fe2O3 system at 1300 and 1400 °C were studied in the whole concentration range by X-ray diffraction (XRD) and scanning electron microscopy (SEM). The isothermal cross-sections of the Nd2O3-Fe2O3 phase diagram at 1300 and 1400 °C are characterized by the presence of three singlephase (A-Nd2O3, NdFeO3, Fe2O3) and two two-phase (A-Nd2O3 + NdFeO3, NdFeO3 + Fe2O3) regions. The composition corresponding to the perovskite phase is 51mol% Nd2O3 - 49mol% Fe2O3. In the next step, the investigation was focused on this composition. Nanocrystalline NdFeO3 powders with perovskite structure were obtained by the Pechini method and heterogeneous precipitation from nitrate solutions. The influence of the production method on the microstructure, morphology and magnetic properties of the NdFeO3 nanopowders was studied. According to XRD, SEM and TEM, the synthesized perovskite NdFeO3 is single-phase with a particle size of 60-90 nm. The morphology of powder particles primarily depends on the synthesis method. The powder showed ferromagnetic behaviour and had saturation magnetization 0.8 and 0.81 emu/g., We acknowledge the financial support of the European Commission through the project H2020-MSCA-RISE 2020 MELON (Grant No. 872631). The authors would like to acknowledgethe access to the equipment of “Servicio General de Apoyo a la Investigación (SAI), Universidad de Zaragoza”., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Production, structure and magnetic properties of nanocomposites based on the perovskite phase LaFeO3

  • Chudinovych, Olga V.
  • Vedel, Dmytro V.
  • Stasyuk, Oleksandr O.
  • Tomila, Tamara V.
  • Aguirre, Myriam H.
The phase relations in the La2O3–Fe2O3 system at 1300 °C were studied in the whole concentration range by X-ray diffraction (XRD) and scanning electron microscopy (SEM). The samples were prepared with a concentration step of 1–5 mol %. The isothermal cross-sections of the La2O3–Fe2O3 phase diagram at 1300 °C are characterized by the presence of three single-phase (A–La2O3, LaFeO3, Fe2O3), two two-phase (A–La2O3+LaFeO3, LaFeO3+Fe2O3) regions. The composition corresponding to the perovskite phase is 49 mol % La2O3–51 mol % Fe2O3. Nanocomposites based on the perovskite phase (LaFeO3) were obtained by the Pechini method and heterogeneous precipitation from nitrate solutions. Solutions of La3+ nitrates, which were obtained by dissolving lanthanum oxide with a content of the main component of 99.99 % in nitric acid. The influence of the production method on the microstructure, morphology, and magnetic properties of nanopowders (LaFeO3) was studied. According to XRD, infrared spectroscopy, SEM, and TEM, the synthesized perovskite LaFeO3 is single-phase with a particle size of 50–60 nm. The morphology of powder particles primarily depends on the method of material synthesis. The powder showed ferrimagnetic magnetic properties and had a specific magnetization 0.2 and 0.15 emu/g., We acknowledge the financial support of the European Commission through the project H2020-MSCA-RISE 2020 MELON (Grant No. 872631). The authors would like to acknowledge the access to the equipment of “Servicio General de Apoyo a la Investigación (SAI), Universidad de Zaragoza”., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Position-sensitive domain-by-domain switchable ferroelectric memristor

  • Risch, Felix
  • Koutsogiannis, Panagiotis
  • Tikhonov, Yuri
  • Razumnaya, Anna G.
  • Magén, César
  • Pardo, José A.
  • Lukyanchuk, Igor
  • Stolichnov, Igor
Domain-wall electronics based on the tunable transport in reconfigurable ferroic domain interfaces offer a promising platform for in-memory computing approaches and reprogrammable neuromorphic circuits. While conductive domain walls have been discovered in many materials, progress in the field is hindered by high-voltage operations, stability of the resistive states and limited control over the domain wall dynamics. Here, we show nonvolatile memristive functionalities based on precisely controllable conductive domain walls in tetragonal Pb(Zr,Ti)O3 thin films within a two-terminal parallel-plate capacitor geometry. Individual submicron domains can be manipulated selectively by position-sensitive low-voltage operations to address distinct resistive states with nanoampere-range conduction readout. Quantitative phase-field simulations reveal a complex pattern of interpenetrating a- and c-domain associated with the formation of 2D conducting layers at the intertwined regions and the emergence of 3D percolation channels of extraordinary high conductivity. Subnanometer resolution polarization mapping experimentally proves the existence of such extensive segments of charged tail-to-tail domain walls with unconventional structure at the ferroelastic-ferroelectric domain boundaries., This project has received funding from the EU Horizon 2020 program under the MSCA-ITN action MANIC, grant agreement No 861153 and MSCA-RISE action MELON, grant agreement No 872631. The authors gratefully acknowledge Dr. B. Fraygola for PLD deposition and Dr. S. Kamaei for helpful discussions. The authors acknowledge research Projects No. PID2020-112914RB-I00, PID2023-147211OB-C22 788, and the Severo Ochoa program CEX2023-001286-S funded by Grant No. MCIN/AEI/10.13039/501100011033. This work was also funded from Regional Gobierno de Aragon through Project Nos. E13_23R and E28_23R, including FEDER funding. A.R. acknowledges the Slovenian Research Agency support (P1-0125). This work was granted access to HPC resources of ”Plateforme MatriCS” within University of Picardie Jules Verne. ”Plateforme MatriCS” is cofinanced by the European Union with the European Regional Development Fund (FEDER) and the Hauts-De-France Regional Council among others., With funding from the Spanish government through the "Severo Ochoa Centre of Excellence" accreditation (CEX2023-001286-S)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Advancements in polyol synthesis: expanding chemical horizons and Néel temperature tuning of CoO nanoparticles

  • Baričić, Miran
  • Nuñez, Jorge M.
  • Aguirre, Myriam H.
  • Hrabovsky, David
  • Seydou, Mahamadou
  • Meneghini, Carlo
  • Peddis, Davide
  • Ammar, Souad
The dataset used and/or analyzed during the current study is available from the corresponding author on reasonable request., The polyol synthesis of CoO nanoparticles (NPs) is typically conducted by dissolving and heating cobalt acetate tetrahydrate and water in diethylene glycol (DEG). This process yields aggregates of approximately 100 nm made of partially aligned primary crystals. However, the synthesis demands careful temperature control to allow the nucleation of CoO while simultaneously preventing reduction, caused by the activity of DEG. This restriction hinders the flexibility to freely adjust synthesis conditions, impeding the ability to obtain particles with varied morpho-structural properties, which, in turn, directly impact chemical and physical attributes. In this context, the growth of CoO NPs in polyol was studied focusing on the effect of the polyol chain length and the synthesis temperature at two different water/cations ratios. During this investigation, we found that longer polyol chains remove the previous limits of the method, allowing the tuning of aggregate size (20–150 nm), shape (spherical-octahedral), and crystalline length (8–35 nm). Regarding the characterization, our focus revolved around investigating the magnetic properties inherent in the synthesized products. From this point of view, two pivotal findings emerged. Firstly, we identified small quantities of a layered hydroxide ferromagnetic intermediate, which acted as interference in our measurements. This intermediate exhibited magnetic properties consistent with features observed in other publications on CoO produced in systems compatible with the intermediate formation. Optimal synthetic conditions that prevent the impurity from forming were found. This resolution clarifies several ambiguities existing in literature about CoO low-temperature magnetic behavior. Secondly, a regular relationship of the NPs' TN with their crystallite size was found, allowing us to regulate TN over ~ 80 K. For the first time, a branching was found in this structure-dependent magnetic feature, with samples of spheroidal morphology consistently having lower magnetic temperatures, when compared to samples with faceted/octahedral shape, providing compelling evidence for a novel physical parameter influencing the TN of a material. These two findings contribute to the understanding of the fundamental properties of CoO and antiferromagnetic materials., The Agence Nationale de la Recherche (ANR) and the Commissariat à l’Investissement d’Avenir (CGI) are gratefully acknowledged for their financial support of this work through the Labex SEAM grant (N°Horge). We also acknowledge the financial support of H2020-MSCA-RISE-2020 MELON Project #872631 and MSCA-RISE-2021 ULTIMATE-I Project #101007825, and the access to TEM equipment at LMA-university of Zaragoza to perform TEM studies. Finally, we acknowledge the staff of the MPBT (physical properties – low temperature) platform of Sorbonne Université for their support., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Phase stability and structural evolution of core/shell iron oxide nanoparticles due to oxidative diffusion: Implications for spintronic application

  • Nuñez, Jorge M.
  • Lima Jr., Enio
  • Lohr, Javier
  • Vásquez Mansilla, Marcelo
  • Zysler, Roberto Daniel
  • Tolley, Alfredo
  • Bartolomé, Fernando
  • Rubín, Javier
  • Hettler, Simon
  • Arenal, Raúl
  • Aguirre, Myriam H.
  • Winkler, Elin L.
Core/shell iron oxide nanoparticles are promising candidates for spintronic applications due to their tunable magnetic properties and interfacial exchange interactions that allow the modulation of spin-polarized conduction. However, their performance depends critically on phase stability and structural integrity under fabrication and operating conditions involving thermal and oxidative diffusion. This study examines the transformation of iron oxide nanoparticles induced by oxidative diffusion in thermal annealing from wüstite to hematite through an intermediate (wüstite)-core/(magnetite–maghemite)-shell structure. The nanoparticles exhibit a rounded cubic morphology, with a distorted C2/m FeO phase at the core under compressive strain along (010), while the Fe3O4 shell exhibits tensile strain along (110). Oxygen diffusion occurs preferentially along [100] from the cube faces, influencing shape evolution. The system exhibits an exchange bias field of up to 3 kOe and enhanced magnetic hardening of up to 4 kOe, attributed to interfacial exchange interactions. Higher annealing temperature promotes the formation of γ-Fe2O3 with ordered vacancies. The exchange bias effect persists, even when the FeO core is smaller than 1 nm in size, indicating that the strain stabilizes the antiferromagnetic (AFM) order and enhances core/shell magnetic coupling. As oxidation proceeds, strain is gradually relaxed, and at 873 K, the oxidation to hematite is promoted, characterized by a Morin transition at 245 K. These findings reveal the intricate relationship between oxidation-driven structural evolution and magnetic behavior in engineered nanoparticle systems, underscoring the critical importance of material selection tailored to specific fabrication processes, operating conditions, and device performance requirements., The authors also gratefully acknowledge the European Commission for the financial support under the H2020-MSCA-RISE-2020 (NESTOR) PROJECT No 101007629, H2020-MSCA-RISE-2020 (ULTIMATE-I) Project No 101007825 and H2020-MSCA-RISE-2019 (MELON) Project No 872631. R.A. and S.H. acknowledge the funding by the Gobierno de Aragón (DGA) under project E13-23R and by the Spanish MICIU (PID2023-151080NB-I00/AEI/10.13039/501100011033, and CEX2023-001286-S MICIU/AEI/10.13039/501100011033)., With funding from the Spanish government through the "Severo Ochoa Centre of Excellence" accreditation (CEX2023-001286-S)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Lattice-tunable substituted iron garnets for low-temperature magnonics

  • Legrand, William
  • Kemna, Yana
  • Schären, Stefan
  • Wang, Hanchen
  • Petrosyan, Davit
  • Holder, Luise
  • Schlitz, Richard
  • Aguirre, Myriam H.
  • Lammel, Michaela
  • Gambardella, Pietro
arXiv:2407.06850v2, The synthesis of nm-thick epitaxial films of iron garnets by physical vapor deposition has opened up exciting opportunities for the on-chip generation and processing of microwave signals encoded in magnons. However, iron garnet thin films suffer from demanding lattice-matching and stoichiometry requirements. Here a new approach to their synthesis is developed, enabling a precise and continuous tuning of iron garnet compositions based on the co-sputtering of binary oxides. By substituting a controlled proportion of iron with additional yttrium, Y3(YxFe5−x)O12 films of high crystalline quality are obtained, combining a widely tunable lattice parameter and excellent magnetization dynamics. This enables iron garnet thin films suited for cryogenic applications, which have long remained impractical due to microwave losses caused by paramagnetic garnet substrates. Low-temperature ferromagnetic resonance confirms the elimination of substrate paramagnetic losses for Y3(YxFe5−x)O12 films lattice-matched to Y3Sc2Ga3O12 (YSGG), a diamagnetic substrate. The Y3(YxFe5−x)O12 system can be matched to other substrates such as (Gd, Y)3Sc2Ga3O12. Bi-substituted films of (Bi0.8Y2.2)Fe5O12 also have ideal lattice matching to YSGG, demonstrating the versatility of this approach. This opens unprecedented options for cation substitutions in iron garnet films, offering a promising avenue to new properties and quantum magnonic devices operating in low-temperature environments., This research was partially supported by the Swiss National Science Foundation (Grant No. 200020-200465). W.L. acknowledges the support of the ETH Zurich Postdoctoral Fellowship Program (21-1 FEL-48). H.W. acknowledges the support of the China Scholarship Council (CSC, Grant No. 202206020091). M.L. and R.S. acknowledge support from the Deutsche Forschungsgemeinschaft (DFG, German Research Foundation) via the SFB 1432, Project No. 425217212. M.L. additionally acknowledges support via Project No. 490730630. The authors acknowledge the financial support of European Commission through Marie Skłodowska-Curie Actions H2020 RISE with the projects MELON (Grant No. 872631) and ULTIMATE-I (Grant No. 101007825), and access to the equipment of “Servicio General de Apoyo a la Investigación (SAI), Universidad de Zaragoza”., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Oxygen vacancy engineering in pulsed laser deposited BaSnO3 thin films on SrTiO3

  • Román Acevedo, Wilson
  • Aguirre, Myriam H.
  • Noheda, Beatriz
  • Rubi, Diego
The data that support the findings of this study are available from the corresponding author upon reasonable request., We demonstrate the tunability of the oxygen content in pulsed laser deposition-grown barium stannate thin films (BaSn O3⁠, BSO) by precisely controlling the background oxygen pressure over a broad range from 0.0004 to 0.13 mbar. The introduction of oxygen vacancies (OV) significantly alters the structural properties of BSO films, inducing a monotonic expansion of the out-of-plane lattice parameter and cell volume as the vacancy concentration increases. The progressive formation of OV was spectroscopically tracked using x-ray photoelectron spectroscopy, providing direct insight into the vacancy evolution. Furthermore, we show that the oxygen stoichiometry in BSO plays a critical role in modulating the sheet resistance of BSO/LaScO3 heterostructures, enabling interface metallic electron conduction. This oxygen content control offers a robust strategy to tailor the electronic properties at the interface, highlighting its potential for oxide electronics and functional interface engineering., We acknowledge support from ANPCyT through project PICT2019-02781, and from the EU-H2020-RISE through project MELON (Grant No. 872631). The financial support from the Groningen Cognitive Systems and Materials Center (CogniGron) and the Ubbo Emmius Foundation of the University of Groningen is appreciated., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Graphene quantum dots drive spontaneous metal reduction to form stable and electroactive core-shell nanocolloids

  • Ventre, Josefina
  • Barrionuevo, Santiago D.
  • Nuñez, Jorge M.
  • Renna, Agustina
  • Faccio, Ricardo
  • Aguirre, Myriam H.
  • Bellino, Martin G.
  • Ibañez, Francisco J.
This work demonstrates a spontaneous synthesis of ∼8.0, ∼7.0, and ∼3.0 nm diameter Au, Ag, and Pt cores; respectively, wrapped by as-synthesized crystalline graphene-quantum dots (GQDs). Functional sp2- and sp3-hybridized carbons play a crucial role upon the synthesis, electronic distribution at the interface, and conductive sites for improving the electrocatalytic response. Au nanohybrids (NHs) demonstrated two-fold increase in current density with respect to conventional citrate-coated Au nanoparticles. This was attributed to conductive sp2- hybridized carbons and the gain of charge density at the surface of Au as demonstrated by DFT calculations. Due to the sp3-carbons at the shell, these NHs also behave like simple chemical compounds because they can be precipitated, stored for long periods of time, and redispersed without apparent changes in their properties. The resultant nanocolloids exhibit exceptional stability under harsh conditions. These attributes make them useful NHs with great potential for broad applications., We gratefully acknowledge financial support from PICT (2019–2188), PIP-2022–2024 0001 (CONICET), and Proyecto de Incentivos 2019-X-887 from UNLP. We also acknowledge the financial support of European Commission through Marie Skłodowska-Curie Actions H2020 RISE with the projects MELON (Grant No. 872631) and ULTIMATE-I (Grant No. 101007825). Authors would like to acknowledge the access of equipment of “Servicio General de Apoyo a la Investigación (SAI), Universidad de Zaragoza”. RF acknowledges the Uruguayan founding institution CSI, ANII, and PEDECIBA. SB and JV want to acknowledge Agostina Chapana for discussion on FT-IR spectrum of GQDs. SB and JV acknowledge CONICET for their scholarships supported by CONICET., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Tuning the memristive response of TaOx- based devices with Ag nanoparticles

  • Leal Martir, Rodrigo
  • Ree, A.J.T. van der
  • Aguirre, Myriam H.
  • Palasantzas, George
  • Rubi, Diego
  • Sánchez, M. J.
arXiv:2602.24168v1, Defect engineering is a key strategy to control resistive switching (RS) in oxide-based memristive devices, where oxygen vacancy (OV) dynamics governs filament formation and rupture. We investigate the effect of Ag nanoparticles (AgNPs) embedded in the top electrode of Pt/Ta2O5/TaO2/Pt memristors and analyze their RS behavior and statistical stability. Devices without AgNPs exhibit two hysteresis switching loops (HSLs) with opposite chiralities, originating from the participation of the Pt/Ta2O5 top interface (TI) and the Ta2O5/TaO2 bottom interface (BI). Incorporating AgNPs reduces the overall device resistance and selectively suppresses one loop, yielding a single, well-defined switching mode. Moreover, devices incorporating AgNPs show markedly reduced cycle-to-cycle variability of the high-resistance state, as confirmed by Weibull analysis, indicating improved endurance and switching reproducibility. Within a filamentary RS framework, we attribute this behavior to local metallization of the TI by AgNPs, which partially inhibits OV transport and confines the RS dynamics to the BI. Numerical simulations with the OV resistive network (OVRN) model successfully reproduce the experimental HSLs, statistical trends, and tunable ON/OFF ratios with AgNPs coverage. These findings demonstrate that targeted interface metallization via metallic nanoparticles provides an effective route to control multi-interface RS dynamics and improve switching stability in without modifying the oxide architecture., The authors would like to thank the ‘Laboratorio de Microscopías Avanzadas’ at ‘Universidad de Zaragoza’ for providing access to their instruments. We acknowledge the support from EU-H2020-RISE project MELON (Grant No. 872631) and ANPCyT (Grant Nos. PICT2019-0654, PICT2019-02781, and PICT2020A-00415)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Device-area selection of memristive transport regimes in epitaxial Hf0.5Zr0.5O2-based ferroelectric devices

  • Tapia Presas, Priscila A.
  • Galarregui, Lautaro
  • Acevedo, Wilson Román
  • Aguirre, Myriam H.
  • Santiso, José
  • Matzen, Sylvia
  • Noheda, Beatriz
  • Rubi, Diego
Ferroelectric memristive devices based on hafnia are promising systems for neuromorphic electronics, yet the interplay between polarization-modulated resistive changes and defect-mediated transport often leads to complex and debated switching mechanisms. Here, we investigate this competition in epitaxial Hf0.5Zr0.5O2/La0.67Sr0.33MnO3 heterostructures with Pt top electrodes by combining structural, ferroelectric, and memristive characterization with a statistical analysis across a broad range of device areas spanning three orders of magnitude. We identify two distinct memristive regimes with opposite resistance–voltage chiralities. Small devices exhibit a low-resistance state that scales inversely with area, consistent with area-distributed electronic transport, while larger devices display an area-independent resistance indicative of localized conductive channels. A statistical nucleation model quantitatively captures this behavior and yields a crossover characteristic area of A*=10 3 um2. This crossover also correlates with the onset of ferroelectric wake-up for the larger devices, linking conductive-channel nucleation and oxygen-vacancy redistribution within a unified physical picture. These results establish lateral device size as a key parameter controlling the dominant transport mechanism in epitaxial hafnia-based devices., Some of the experiments reported here were carried out within the NFFA-Europe access Proposal Nos. ID478 and ID579 (2023), funded by the European Union’s Horizon 2020 research and innovation programme under Grant Agreement No. 101007417, and the CNRS-IRP action PhenomeNaS. We also acknowledge support from the EU-H2020-RISE project MELON (Grant No. 872631). We also acknowledge the financial support from the Instituto de Tecnología (INTEC) of the Universidad Argentina de la Empresa (UADE), project code A26T63. The financial support from the Groningen Cognitive Systems and Materials Center (CogniGron) and the Ubbo Emmius Foundation of the University of Groningen is appreciated. We thank M. Sarott from the University of Groningen for his assistance with the PFM measurements. Research at the Center for Nanoscience and Nanotechnology was partially supported by the French RENATECH network., Peer reviewed
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Epitaxial ferroelectric memristors integrated with silicon

  • Rengifo, Miguel
  • Aguirre, Myriam H.
  • Sirena, Martín
  • Lüders, Ulrike
  • Rubi, Diego
Neuromorphic computing requires the development of solid-state units able to electrically mimic the behavior of biological neurons and synapses. This can be achieved by developing memristive systems based on ferroelectric oxides. In this work we fabricate and characterize high quality epitaxial BaTiO3-based memristors integrated with silicon. After proving the ferroelectric character of BaTiO3 we tested the memristive response of LaNiO3/BaTiO3/Pt microstructures and found a complex behavior which includes the co-existence of volatile and non-volatile effects, arising from the modulation of the BaTiO3/Pt Schottky interface by the direction of the polarization coupled to oxygen vacancy electromigration to/from the interface. This produces remanent resistance loops with tunable ON/OFF ratio and asymmetric resistance relaxations. These properties might be harnessed for the development of neuromorphic hardware compatible with existing silicon-based technology.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Novel Ir1–xCoxO2 thin films: Growth and characterization

  • Laguna–Marco, M. A.
  • Herrero-Albillos, J.
  • Aguirre, M. H.
  • Rueda-Jiménez, M.
  • Mikulska, I.
Ir1–xCoxO2 thin films have been prepared by reactive co–sputtering deposition at room temperature. Composition, structure, electronic properties and electric and magnetic behavior have been analyzed by different techniques including XRR, XRD, TEM microscopy, SQUID magnetometry, electrical resistivity and XAS spectroscopy. After annealing, an Ir1–xCoxO2 substitutional solid solution phase with rutile crystal structure was achieved for a wide Co-doping range 0 ≤ x ≤ 0.6. Starkly departing from the highly insulating behavior of CoO and Co3O4, the electrical resistivity at room temperature of our films is only slightly higher than that of IrO2. Likewise, our work shows that the magnetic response of the doped films is very similar to that of the paramagnetic parent IrO2. Neither ferromagnetism nor enhanced paramagnetism is observed. XAS spectra indicate a Co3+ oxidation state and, correspondingly, an oxidation state of ∼5+ for Ir ions in the polycrystalline Ir0.6Co0.4O2 film. By application of sum rules, a 13 % increase in the spin–orbit coupling is found despite the lattice shrinkage causes a detrimental bandwidth broadening.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Stacking-configuration-preserved Graphene quantum dots electrochemically obtained from CVD Graphene

  • Barrionuevo, Santiago D.
  • Fioravanti, Federico
  • Núñez, Jorge M.
  • Muñeton Arboleda, David
  • Lacconi, Gabriela I.
  • Bellino, Martín G.
  • Aguirre, Myriam H.
  • Ibáñez, Francisco J.
The layer stacking morphology in nanocarbons is paramount for achieving new properties and outperforming applications. Here, we demonstrate that graphene quantum dots (GQDs) retain crystallinity and a stacking structure from CVD graphene grown on Ni foam. Our results reveal that GQD subdomains comprise a few-layer graphene structure in the AB···AB and ABC···ABC stacking configuration. HR-TEM images along with a multiple-approach characterization (XRD, XPS, UV–vis, AFM, and ATR-IR) exhibit ∼3.0 to ∼8.0 nm crystalline GQDs with 2–6 graphene layers thick indicating a disk-shape structure. The UV–vis profiles show changes in color of the dispersion (from colorless to red) during and after the electrochemistry, suggesting a systematic electrooxidation of graphene into smaller, highly crystalline, and more complex sp2/sp3 structures. Importantly, a control experiment performed under the same conditions but with a graphitic rod exhibited large, polydisperse, and multilayer carbon structures. This work demonstrates a relatively easy electrochemical synthesis to obtain GQDs which retain the pristine and, in turn, distinctive structure of graphene grown on Ni foam.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Magnetic transition and spin-polarized two-dimensional electron gas controlled by polarization switching in strained CaMnO3/BaTiO3

  • Di Napoli, S.
  • Román, A.
  • Llois, A. M.
  • Aguirre, M. H.
  • Steren, L. B.
  • Barral, M. A.
Ab initio calculations show the presence of a strong magnetoelectric interfacial coupling in a CaMnO 3 ultrathin film grown on a strained BaTiO 3 Ferroelectric film. This heterostructure presents a polarization driven magnetic transition from a G-type to an A-type antiferromagnetic structure. Together with this magnetic transition we find a metallic behavior at the interface between these two insulators, where the charge character of the carriers can be tuned from electrons to holes by switching the electric polarization direction of the ferroelectric film. Besides, the electron gas is spin polarized while the hole gas is not.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Advancements in polyol synthesis: expanding chemical horizons and Néel temperature tuning of CoO nanoparticles

  • Baricic, Miran
  • Nuñez, Jorge M.
  • Aguirre, Myriam H.
  • Hrabovsky, David
  • Seydou, Mahamadou
  • Meneghini, Carlo
  • Peddis, Davide
  • Ammar, Souad
The polyol synthesis of CoO nanoparticles (NPs) is typically conducted by dissolving and heating cobalt acetate tetrahydrate and water in diethylene glycol (DEG). This process yields aggregates of approximately 100 nm made of partially aligned primary crystals. However, the synthesis demands careful temperature control to allow the nucleation of CoO while simultaneously preventing reduction, caused by the activity of DEG. This restriction hinders the flexibility to freely adjust synthesis conditions, impeding the ability to obtain particles with varied morpho-structural properties, which, in turn, directly impact chemical and physical attributes. In this context, the growth of CoO NPs in polyol was studied focusing on the effect of the polyol chain length and the synthesis temperature at two different water/cations ratios. During this investigation, we found that longer polyol chains remove the previous limits of the method, allowing the tuning of aggregate size (20–150 nm), shape (spherical-octahedral), and crystalline length (8–35 nm). Regarding the characterization, our focus revolved around investigating the magnetic properties inherent in the synthesized products. From this point of view, two pivotal findings emerged. Firstly, we identified small quantities of a layered hydroxide ferromagnetic intermediate, which acted as interference in our measurements. This intermediate exhibited magnetic properties consistent with features observed in other publications on CoO produced in systems compatible with the intermediate formation. Optimal synthetic conditions that prevent the impurity from forming were found. This resolution clarifies several ambiguities existing in literature about CoO low-temperature magnetic behavior. Secondly, a regular relationship of the NPs' TN with their crystallite size was found, allowing us to regulate TN over ~ 80 K. For the first time, a branching was found in this structure-dependent magnetic feature, with samples of spheroidal morphology consistently having lower magnetic temperatures, when compared to samples with faceted/octahedral shape, providing compelling evidence for a novel physical parameter influencing the TN of a material. These two findings contribute to the understanding of the fundamental properties of CoO and antiferromagnetic materials.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Multi-mem behavior at reduced voltages in La1/2¿Sr1/2¿Mn1/2¿Co1/2¿O3-¿ perovskite modified with Sm:Ce¿O2

  • Román Acevedo, Wilson
  • Aguirre, Myriam H.
  • Noheda, Beatriz
  • Rubi, Diego
The use of machine learning algorithms is exponentially growing and concerns are being raised about their sustainability. Neuromorphic computing aims to mimic the architecture and the information processing mechanisms of the mammalian brain, appearing as the only avenue that offers significant energy savings compared to the standard digital computers. Memcapacitive devices, which can change their capacitance between different nonvolatile states upon the application of electrical stimulation, can significantly reduce the energy consumption of bio-inspired circuitry. In the present work, we study the multi-mem (memristive and memcapacitive) behavior of devices based on thin films of the topotactic redox L⁢a1/2⁢S⁢r1/2⁢M⁢n1/2⁢C⁢o1/2⁢O3− (LSMCO) perovskite modified with Sm:Ce⁢O2 (SCO), grown on Nb:SrTiO3 with (001) and (110) out-of-plane orientations. Either the self-assembling at the nanoscale of both LSMCO and SCO phases or the doping with Ce(Sm) of the LSMCO perovskite were observed for different fabrication conditions and out-of-plane orientations. The impact of these changes on the device electrical behavior was determined. The optimum devices resulted those with (110) orientation and Ce(Sm) doping the perovskite. These devices displayed a multi-mem behavior with robust memcapacitance and significantly lower operation voltages (especially the reset voltage) in comparison with devices based on pristine LSMCO. In addition, they were able to endure electrical cycling—and the concomitant perovskite topotactic redox transition between oxidized and reduced phases—without suffering nanostructural changes nor cationic segregation. We link these properties to an enhanced perovskite reducibility upon Ce(Sm) doping. Our work contributes to increasing the reliability of LSMCO-based multi-mem systems and to reducing their operating voltages closer to the 1 V threshold, which are key issues for the development of nanodevices for neuromorphic or in-memory computing.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Production, structure and magnetic properties of nanocomposites based on the perovskite phase LaFeO3

  • Chudinovych, O.V.
  • Vedel, D.V.
  • Stasyuk, O.O.
  • Tomila, T.V.
  • Aguirre, M.H.
The phase relations in the La2O3–Fe2O3 system at 1300 °C were studied in the whole concentration range by X-ray diffraction (XRD) and scanning electron microscopy (SEM). The samples were prepared with a concentration step of 1–5 mol %. The isothermal cross-sections of the La2O3–Fe2O3 phase diagram at 1300 °C are characterized by the presence of three single-phase (A–La2O3, LaFeO3, Fe2O3), two two-phase (A–La2O3+LaFeO3, LaFeO3+Fe2O3) regions. The composition corresponding to the perovskite phase is 49 mol % La2O3–51 mol % Fe2O3. Nanocomposites based on the perovskite phase (LaFeO3) were obtained by the Pechini method and heterogeneous precipitation from nitrate solutions. Solutions of La3+ nitrates, which were obtained by dissolving lanthanum oxide with a content of the main component of 99.99 % in nitric acid. The influence of the production method on the microstructure, morphology, and magnetic properties of nanopowders (LaFeO3) was studied. According to XRD, infrared spectroscopy, SEM, and TEM, the synthesized perovskite LaFeO3 is single-phase with a particle size of 50–60 nm. The morphology of powder particles primarily depends on the method of material synthesis. The powder showed ferrimagnetic magnetic properties and had a specific magnetization 0.2 and 0.15 emu/g.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Phase relations in the Nd2O3-Fe2O3 system: Structure and magnetic properties of perovskite NdFeO3 ceramics

  • Chudinovych, Olga V.
  • Vedel, Dmytro V.
  • Stasyuk, Oleksandr O.
  • Samelyuk, Anatoly V.
  • Aguirre, Myriam H.
The phase relations in the Nd2O3-Fe2O3 system at 1300 and 1400 degrees C were studied in the whole concentration range by X-ray diffraction (XRD) and scanning electron microscopy (SEM). The isothermal cross-sections of the Nd2O3-Fe2O3 phase diagram at 1300 and 1400 degrees C are characterized by the presence of three single-phase (A-Nd2O3, NdFeO3, Fe2O3) and two two-phase (A-Nd2O3 + NdFeO3, NdFeO3 + Fe2O3) regions. The composition corresponding to the perovskite phase is 51 mol% Nd2O3 - 49 mol% Fe2O3. In the next step, the investigation was focused on this composition. Nanocrystalline NdFeO3 powders with perovskite structure were obtained by the Pechini method and heterogeneous precipitation from nitrate solutions. The influence of the production method on the microstructure, morphology and magnetic properties of the NdFeO3 nanopowders was studied. According to XRD, SEM and TEM, the synthesized perovskite NdFeO3 is single-phase with a particle size of 60-90 nm. The morphology of powder particles primarily depends on the synthesis method. The powder showed ferromagnetic behaviour and had saturation magnetization 0.8 and 0.81 emu/g.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Position-sensitive domain-by-domain switchable ferroelectric memristor

  • Risch, Felix
  • Koutsogiannis, Panagiotis
  • Tikhonov, Yuri
  • Razumnaya, Anna G.
  • Magén, César
  • Pardo, José A.
  • Lukyanchuk, Igor
  • Stolichnov, Igor
Domain-wall electronics based on the tunable transport in reconfigurable ferroic domain interfaces offer a promising platform for in-memory computing approaches and reprogrammable neuromorphic circuits. While conductive domain walls have been discovered in many materials, progress in the field is hindered by high-voltage operations, stability of the resistive states and limited control over the domain wall dynamics. Here, we show nonvolatile memristive functionalities based on precisely controllable conductive domain walls in tetragonal Pb(Zr,Ti)O3 thin films within a two-terminal parallel-plate capacitor geometry. Individual submicron domains can be manipulated selectively by position-sensitive low-voltage operations to address distinct resistive states with nanoampere-range conduction readout. Quantitative phase-field simulations reveal a complex pattern of interpenetrating a- and c-domain associated with the formation of 2D conducting layers at the intertwined regions and the emergence of 3D percolation channels of extraordinary high conductivity. Subnanometer resolution polarization mapping experimentally proves the existence of such extensive segments of charged tail-to-tail domain walls with unconventional structure at the ferroelastic-ferroelectric domain boundaries.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Lattice-Tunable Substituted Iron Garnets for Low-Temperature Magnonics

  • Legrand, William
  • Kemna, Yana
  • Schären, Stefan
  • Wang, Hanchen
  • Petrosyan, Davit
  • Holder, Luise
  • Schlitz, Richard
  • Aguirre, Myriam H.
  • Lammel, Michaela
  • Gambardella, Pietro
The synthesis of nm-thick epitaxial films of iron garnets by physical vapor deposition has opened up exciting opportunities for the on-chip generation and processing of microwave signals encoded in magnons. However, iron garnet thin films suffer from demanding lattice-matching and stoichiometry requirements. Here a new approach to their synthesis is developed, enabling a precise and continuous tuning of iron garnet compositions based on the co-sputtering of binary oxides. By substituting a controlled proportion of iron with additional yttrium, Y3(YxFe5−x)O12 films of high crystalline quality are obtained, combining a widely tunable lattice parameter and excellent magnetization dynamics. This enables iron garnet thin films suited for cryogenic applications, which have long remained impractical due to microwave losses caused by paramagnetic garnet substrates. Low-temperature ferromagnetic resonance confirms the elimination of substrate paramagnetic losses for Y3(YxFe5−x)O12 films lattice-matched to Y3Sc2Ga3O12 (YSGG), a diamagnetic substrate. The Y3(YxFe5−x)O12 system can be matched to other substrates such as (Gd, Y)3Sc2Ga3O12. Bi-substituted films of (Bi0.8Y2.2)Fe5O12 also have ideal lattice matching to YSGG, demonstrating the versatility of this approach. This opens unprecedented options for cation substitutions in iron garnet films, offering a promising avenue to new properties and quantum magnonic devices operating in low-temperature environments.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Phase Stability and Structural Evolution of Core/Shell Iron Oxide Nanoparticles Due to Oxidative Diffusion: Implications for Spintronic Applications

  • Nuñez, Jorge M.
  • Lima, Enio
  • Lohr, Javier Hernán
  • Vásquez Mansilla, Marcelo
  • Zysler, Roberto D.
  • Tolley, Alfredo
  • Bartolomé, Fernando
  • Rubín, Javier
  • Hettler, Simón
  • Arenal, Raúl
  • Aguirre, Myriam Haydee
  • Winkler, Elin L.
Core/shell iron oxide nanoparticles are promising candidates for spintronic applications due to their tunable magnetic properties and interfacial exchange interactions that allow the modulation of spin-polarized conduction. However, their performance depends critically on phase stability and structural integrity under fabrication and operating conditions involving thermal and oxidative diffusion. This study examines the transformation of iron oxide nanoparticles induced by oxidative diffusion in thermal annealing from wüstite to hematite through an intermediate (wüstite)-core/(magnetite–maghemite)-shell structure. The nanoparticles exhibit a rounded cubic morphology, with a distorted C2/m FeO phase at the core under compressive strain along (010), while the Fe3O4 shell exhibits tensile strain along (110). Oxygen diffusion occurs preferentially along [100] from the cube faces, influencing shape evolution. The system exhibits an exchange bias field of up to 3 kOe and enhanced magnetic hardening of up to 4 kOe, attributed to interfacial exchange interactions. Higher annealing temperature promotes the formation of γ-Fe2O3 with ordered vacancies. The exchange bias effect persists, even when the FeO core is smaller than 1 nm in size, indicating that the strain stabilizes the antiferromagnetic (AFM) order and enhances core/shell magnetic coupling. As oxidation proceeds, strain is gradually relaxed, and at 873 K, the oxidation to hematite is promoted, characterized by a Morin transition at 245 K. These findings reveal the intricate relationship between oxidation-driven structural evolution and magnetic behavior in engineered nanoparticle systems, underscoring the critical importance of material selection tailored to specific fabrication processes, operating conditions, and device performance requirements.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Graphene Quantum Dots Drive Spontaneous Metal Reduction to form Stable and Electroactive Core‐Shell Nanocolloids

  • Ventre, Josefina
  • Barrionuevo, Santiago D.
  • Nuñez, Jorge M.
  • Renna, Agustina
  • Faccio, Ricardo
  • Aguirre, Myriam H.
  • Bellino, Martin G.
  • Ibañez, Francisco J.
This work demonstrates a spontaneous synthesis of ∼8.0, ∼7.0, and ∼3.0 nm diameter Au, Ag, and Pt cores; respectively, wrapped by as‐synthesized crystalline graphene‐quantum dots (GQDs). Functional sp2‐ and sp3‐hybridized carbons play a crucial role upon the synthesis, electronic distribution at the interface, and conductive sites for improving the electrocatalytic response. Au nanohybrids (NHs) demonstrated two‐fold increase in current density with respect to conventional citrate‐coated Au nanoparticles. This was attributed to conductive sp2‐ hybridized carbons and the gain of charge density at the surface of Au as demonstrated by DFT calculations. Due to the sp3‐carbons at the shell, these NHs also behave like simple chemical compounds because they can be precipitated, stored for long periods of time, and redispersed without apparent changes in their properties. The resultant nanocolloids exhibit exceptional stability under harsh conditions. These attributes make them useful NHs with great potential for broad applications.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Tuning the memristive response of TaOx- based devices with Ag nanoparticles

  • Leal Martir, R.
  • van der Ree, A. J. T.
  • Aguirre, M.H.
  • Palasantzas, G.
  • Rubi, D.
  • Sánchez, M.J.
Defect engineering is a key strategy to control resistive switching (RS) in oxide-based memristive devices, where oxygen vacancy (OV) dynamics governs filament formation and rupture. We investigate the effect of Ag nanoparticles (AgNPs) embedded in the top electrode of Pt/Ta2O5/TaO2/Pt memristors and analyze their RS behavior and statistical stability. Devices without AgNPs exhibit two hysteresis switching loops (HSLs) with opposite chiralities, originating from the participation of the Pt/Ta2O5 top interface (TI) and the Ta2O5/TaO2 bottom interface (BI). Incorporating AgNPs reduces the overall device resistance and selectively suppresses one loop, yielding a single, well-defined switching mode. Moreover, devices incorporating AgNPs show markedly reduced cycle-to-cycle variability of the high-resistance state, as confirmed by Weibull analysis, indicating improved endurance and switching reproducibility. Within a filamentary RS framework, we attribute this behavior to local metallization of the TI by AgNPs, which partially inhibits OV transport and confines the RS dynamics to the BI. Numerical simulations with the OV resistive network (OVRN) model successfully reproduce the experimental HSLs, statistical trends, and tunable ON/OFF ratios with AgNPs coverage. These findings demonstrate that targeted interface metallization via metallic nanoparticles provides an effective route to control multi-interface RS dynamics and improve switching stability in without modifying the oxide architecture.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Coexistence of volatile and nonvolatile memristive effects in phase-separated La0.5Ca0.5MnO3-based devices

  • Ramírez, G.A.
  • Román Acevedo, W.
  • Rengifo, M.
  • Núñez, J. M.
  • Aguirre, M.H.
  • Briático, J.
  • Rubi, D.
In this work, we have investigated the coexistence of volatile and nonvolatile memristive effects in epitaxial phase-separated La0.5Ca0.5MnO3 thin films. At low temperatures (50 K), we observed volatile resistive changes arising from self-heating effects in the vicinity of a metal-to-insulator transition. At higher temperatures (140 and 200 K), we measured a combination of volatile and nonvolatile effects arising from the synergy between self-heating effects and ferromagnetic-metallic phase growth induced by an external electrical field. The results reported here add phase separated manganites to the list of materials that can electrically mimic, on the same device, the behavior of both neurons and synapses, a feature that might be useful for the development of neuromorphic computing hardware.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Sol-gel synthesis and multiferroic properties of pyrochlore-free Pb(Fe0.5Nb0.5)O3 thin films

  • Imhoff, L.
  • Di Marco, M. B.
  • Barolin, S. A.
  • Rengifo, M. A.
  • Aguirre, M. H.
  • Stachiotti, M. G.
Lead iron niobate (PbFe0.5Nb0.5O3 – PFN) thin films were synthesized by a modified sol-gel route, which offers the advantage of a rapid, simple and non-toxic reaction method. Polycrystalline perovskite-structured PFN thin films without pyrochlore phases were obtained on Pt/Ti/SiO2/Si substrates after sintering by rapid thermal annealing at 650 °C. TEM and AFM images confirmed the excellent quality of the sintered film, while EDS spectroscopy revealed the presence of oxygen vacancies near the film/substrate interface. Electric measurements show good dielectric properties and ferroelectric behavior, characterized by typical C–V curves and well-defined P-E ferroelectric loops at 1 kHz, with remanent polarization values of ∼12 μC/cm2. The polarization, however, increases with decreasing frequency, indicating the presence of leakage currents. I–V measurements show a significant increase in DC-conduction at relatively low fields (around 100 kV/cm). The films display ferromagnetic behavior at room temperature, with magnetic remanence around 30 emu/cm3 and a coercive field of 1 kOe. These values are significantly higher than those obtained for PFN powders fabricated by the same sol-gel route, as well as the magnetization values reported in the literature for epitaxial films.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Effects of silver nanoparticle doping on electrical, optical, and photovoltaic properties of PbZrxTi1-xO3 thin films synthesized by sol–gel

  • Di Marco, M. B.
  • Imhoff, L.
  • Roldán, M. V.
  • Santiago, M. L.
  • Aguirre, M. H.
  • Pellegri, N.
  • Stachiotti, M. G.
The effects produced by the incorporation of silver nanoparticles (Ag-NPs) of an average size of ∼4 nm on the electrical, optical, and photovoltaic properties of PbZr0.52Ti0.48O3 (PZT) thin films are investigated. The films were synthesized by a chemical solution deposition process, and two different distributions of nanoparticles in the PZT matrix were tested: (1) alternated Ag-NPs and PZT layers, and (2) distributed Ag-NPs over the entire film volume. The resulting films, with thicknesses between 200 and 270 nm, display no segregation of secondary phases, and good dielectric and ferroelectric properties. An increase in remnant polarization is observed when the Ag-NPs are distributed over the volume, which is ascribed to the modification of the film texture. The incorporation of Ag-NPs into the PZT matrix produces an enhancement of the photocurrent density under UV illumination of ∼30%.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Fluorescent graphene quantum dots-enhanced machine learning for the accurate detection and quantification of Hg2+ and Fe3+ in real water samples

  • Llaver, Mauricio
  • Barrionuevo, Santiago D.
  • Núñez, Jorge M.
  • Chapana, Agostina L.
  • Wuilloud, Rodolfo G.
  • Aguirre, Myriam H.
  • Ibáñez, Francisco J.
Selective, accurate, fast detection with minimal usage of instrumentation has become paramount nowadays in the areas of environmental monitoring. Herein, we chemically modified fluorescent graphene quantum dots (GQDs) and trained a machine learning (ML) algorithm for the selective quantification of Hg2+ and Fe3+ ions present in real water samples. The probe is obtained via the electrosynthesis of CVD graphene in the presence of urea, followed by functionalization with 1-nitroso-2-naphthol (NN). The functionalization with NN moieties dramatically improves the selectivity and sensitivity of the probe toward Hg2+ and Fe3+, as demonstrated by LODs of 0.001 and 0.003 mg L−1, respectively. Simulations performed by time-dependent density functional theory (TD-DFT) reveals that the NN molecules within the GQDs are responsible for the florescence emission of the probe. The emission spectra profiles exhibited distinct characteristics between Hg2+ and Fe3+, enabling the ML model to precisely quantify and differentiate between both analytes present in natural and drinking waters. The ML results were further validated by measurements via cold vapor-atomic fluorescence spectroscopy and UV–vis spectroscopy. Our work demonstrates how chemical modification of GQDs, guided by an efficient ML model, markedly enhances sensitivity and selectivity in detecting harmful ions while critically reducing experiments and instrument handling.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Enhanced photocurrent response in epitaxial multiferroic 0.5PZT–0.5PFN thin films

  • Imhoff, Lucía
  • Rengifo, Miguel A.
  • Caicedo Roque, José M.
  • Padilla-Pantoja, Jessica
  • Santiso, José
  • Stachiotti, Marcelo G.
  • Aguirre, Myriam H.
The exploration of novel multiferroic materials with strong coupling between ferroelectric polarization and photovoltaic effects is crucial for next-generation optoelectronic devices. In this study, we characterized highly oriented – multiferroic thin films grown by pulsed laser deposition on (001) substrates with a bottom electrode. The films exhibited excellent crystalline quality, with a single perovskite phase and (001) orientation. They displayed good ferroelectric properties (remanent polarization , PUND; coercive field ), alongside weak ferromagnetic behavior at room temperature (remanence 1.30 ; coercive field 90 ). Photovoltaic measurements demonstrated a robust, polarization-dependent photoresponse under 403 nm monochromatic laser illumination, achieving values between A cm. This compelling observation confirms the intrinsic coupling between ferroelectric polarization and photovoltaic effects, highlighting the considerable promise of these single-phase multiferroic thin films for advanced photovoltaic and optoelectronic memory applications.