Skip to main content

HIGH-FREQUENCY ACOUSTIC LASERS FOR SENSING AND TIME-KEEPING APPLICATIONS

RYC-2014-15392

•
Funding agency name Ministerio de Ciencia e Innovación
Funding agency acronym MICINN
Program Programa Estatal de Promoción del Talento y su Empleabilidad en I+D+i
Subprogram Subprograma Estatal de Incorporación
Call Ramón y Cajal
Call year 2014
State Plan 2013-2016 Plan Estatal de Investigación Científica y Técnica y de Innovación
Management unit Secretaría de Estado de Educación, Formación Profesional y Universidades
Beneficiary centre FUNDACIÓ INSTITUT CATALÀ DE NANOCIÈNCIA I NANOTECNOLOGIA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 23
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Injection locking in an optomechanical coherent phonon source

  • Arregui, Guillermo
  • Colombano, Martín F.
  • Maire, Jeremie
  • Pitanti, Alessandro
  • Capuj, Néstor E.
  • Sotomayor-Torres, Clivia M.
  • Navarro-Urrios, Daniel
  • Griol Barres, Amadeu
  • Martínez, Alejandro|||0000-0001-5448-0140
[EN] Spontaneous locking of the phase of a coherent phonon source to an external reference is demonstrated in a deeply sideband-unresolved optomechanical system. The high-amplitude mechanical oscillations are driven by the anharmonic modulation of the radiation pressure force that result from an absorption-mediated free-carrier/temperature limit cycle, i.e., self-pulsing. Synchronization is observed when the pump laser driving the mechanical oscillator to a self-sustained state is modulated by a radiofrequency tone. We employ a pump-probe phonon detection scheme based on an independent optical cavity to observe only the mechanical oscillator dynamics. The lock range of the oscillation frequency, i.e., the Arnold tongue, is experimentally determined over a range of external reference strengths, evidencing the possibility to tune the oscillator frequency for a range up to 350 kHz. The stability of the coherent phonon source is evaluated via its phase noise, with a maximum achieved suppression of 44 dBc/Hz at 1 kHz offset for a 100 MHz mechanical resonator. Introducing a weak modulation in the excitation laser reveals as a further knob to trigger, control and stabilize the dynamical solutions of self-pulsing based optomechanical oscillators, thus enhancing their potential as acoustic wave sources in a single-layer silicon platform., This research was funded by EU FET Open project PHENOMEN (GA: 713450). ICN2 is supported by the Severo Ochoa program from the Spanish Research Agency (AEI, grant no. SEV-2017-0706) and by the CERCA Programme/Generalitat de Catalunya. G. A. and C. M. S.-T. acknowledge the support from the Spanish MICINN project SIP (PGC2018-101743-B-I00). D. N. U., G. A. and M. F. C. gratefully acknowledge the support of a Ramon y Cajal postdoctoral fellowship (RYC-2014-15392), a BIST studentship, and a Severo Ochoa studentship, respectively. D. N. U. acknowledges the funding through the Ministry of Science, Innovation and Universities (PGC2018-094490-B-C22).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Optical modulation of coherent phonon emission in optomechanical cavities

  • Maire, Jeremie
  • Arregui, Guillermo
  • Capuj, Nestor E.
  • Colombano, Martín F.
  • Sotomayor-Torres, Clivia M.
  • Navarro-Urrios, Daniel
  • Griol Barres, Amadeu
  • Martínez, Alejandro|||0000-0001-5448-0140
[EN] Optomechanical (OM) structures are well suited to study photon-phonon interactions, and they also turn out to be potential building blocks for phononic circuits and quantum computing. In phononic circuits, in which information is carried and processed by phonons, OM structures could be used as interfaces to photons and electrons thanks to their excellent coupling efficiency. Among the components required for phononic circuits, such structures could be used to create coherent phonon sources and detectors, but more complex functions remain challenging. Here, we propose and demonstrate a way to modulate the coherent phonon emission from OM crystals by a photothermal effect induced by an external laser, effectively creating a phonon switch working at ambient conditions of pressure and temperature and the working speed of which is only limited by the build-up time of the mechanical motion of the OM structure. We additionally demonstrate two other modulation schemes: modulation of harmonics in which the mechanical mode remains active but different harmonics of the optical force are used, and modulation to and from a chaotic regime. Furthermore, due to the local nature of the photothermal effect used here, we expect this method to allow us to selectively modulate the emission of any single cavity on a chip without affecting its surroundings in the absence of mechanical coupling between the structures, which is an important step toward freely controllable networks of OM phonon emitters. (c) 2018 Author(s)., This work was supported by the European Comission FET Open project PHENOMEN (No. H2020-EU-713450) and the Spanish MINECO project PHENTOM (No. FIS2015-70862-P). The ICN2 is funded by the CERCA programme, the Generalitat de Catalunya, and supported by the Severo Ochoa programme of the Spanish MINECO Grant No. SEV-2013-0295. D.N.U. and M.F.C. gratefully acknowledge the support of a Ramon y Cajal postdoctoral fellowship (No. RYC-2014-15392) and a Severo Ochoa studentship, respectively. The authors thank F. Alzina for fruitful discussions.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Properties of nanocrystalline silicon probed by optomechanics

  • Navarro-Urrios, Daniel
  • Colombano, Martín F.
  • Maire, Jeremie
  • Chávez-Ángel, Emigdio
  • Arregui, Guillermo
  • Capuj, Néstor E.
  • Devos, Arnaud
  • Grigoras, Kestutis
  • Häkkinen, Teija
  • Saarilahti, Jaakko
  • Makkonen, Tapani
  • Sotomayor-Torres, Clivia M.
  • Ahopelto, Jouni
  • Griol Barres, Amadeu
  • Bellieres, Laurent Christophe
  • Martínez, Alejandro|||0000-0001-5448-0140
[EN] Nanocrystalline materials exhibit properties that can differ substantially from those of their single crystal counterparts. As such, they provide ways to enhance and optimize their functionality for devices and applications. Here, we report on the optical, mechanical and thermal properties of nanocrystalline silicon probed by means of optomechanical nanobeams to extract information of the dynamics of optical absorption, mechanical losses, heat generation and dissipation. The optomechanical nanobeams are fabricated using nanocrystalline films prepared by annealing amorphous silicon layers at different temperatures. The resulting crystallite sizes and the stress in the films can be controlled by the annealing temperature and time and, consequently, the properties of the films can be tuned relatively freely, as demonstrated here by means of electron microscopy and Raman scattering. We show that the nanocrystallite size and the volume fraction of the grain boundaries play a key role in the dissipation rates through nonlinear optical and thermal processes. Promising optical (13,000) and mechanical (1700) quality factors were found in the optomechanical cavity realized in the nanocrystalline Si resulting from annealing at 950 degrees C. The enhanced absorption and recombination rates via the intragap states and the reduced thermal conductivity boost the potential to exploit these nonlinear effects in applications including Nanoelectromechanical systems (NEMS), phonon lasing and chaos-based devices., The following support is gratefully acknowledged: the European Commission project PHENOMEN (H2020-EU-FET Open GA no. 713450), the Spanish Severo Ochoa Excellence program (SEV-2017-0706), CMST and ECA: the Spanish MICINN project SIP (PGC2018-101743-B-I00), DNU and AM: the Spanish MICINN project PGC2018-094490-B-C22. DNU holds a Ramon y Cajal postdoctoral fellowship (RYC-2014-15392); MFC and GA hold a S. Ochoa and a M. S. Curie COFUND BIST postgraduate studentship, respectively.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Nanocrystalline silicon optomechanical cavities

  • Navarro-Urrios, D.
  • Capuj, N.E.
  • Maire, J.
  • Colombano, M.F.
  • Jaramillo-Fernandez, J.
  • Chavez-Angel, E.
  • Martín-Rodríguez, Leopoldo Luis
  • Sotomayor-Torres, C.M.
  • Ahopelto, J.
  • Mercadé, Laura|||0000-0002-4994-7727
  • Griol Barres, Amadeu
  • Martínez, Alejandro|||0000-0001-5448-0140
[EN] Silicon on insulator photonics has offered a versatile platform for the recent development of integrated optomechanical circuits. However, there are some constraints such as the high cost of the wafers and limitation to a single physical device level. In the present work we investigate nanocrystalline silicon as an alternative material for optomechanical devices. In particular we demonstrate that optomechanical crystal cavities fabricated of nanocrystalline silicon have optical and mechanical properties enabling non-linear dynamical behaviour and effects such as thermo-optic/free-carrier-dispersion self-pulsing, phonon lasing and chaos, all at low input laser power and with typical frequencies as high as 0.3 GHz. (C) 2018 Optical Society of America under the terms of the OSA Open Access Publishing Agreement, European Commission project PHENOMEN (H2020-EU-713450), MINECO Severo Ochoa Excellence program (SEV-2013-0295), MINECO (FIS2015-70862-P, RYC-2014-15392) and CERCA Programme/Generalitat de Catalunya.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

All-optical radio-frequency modulation of Anderson-localized modes

  • Arregui, Guillermo
  • Navarro-Urrios, D.
  • Kehagias, N.
  • Sotomayor Torres, C. M.
  • García Fernández, Pedro David
All-optical modulation of light relies on exploiting intrinsic material nonlinearities [V. R. Almeida et al., Nature 431, 1081 (2004)]. However, this optical control is rather challenging due to the weak dependence of the refractive index and absorption coefficients on the concentration of free carriers in standard semiconductors [R. A. Soref and B. R. Bennett, Proc. SPIE 704, 32 (1987)]. To overcome this limitation, resonant structures with high spatial and spectral confinement are carefully designed to enhance the stored electromagnetic energy, thereby requiring lower excitation power to achieve significant nonlinear effects [K. Nozaki et al., Nat. Photonics 4, 477 (2010)]. Small mode-volume and high-quality (Q)-factor cavities also offer an efficient coherent control of the light field and the targeted optical properties. Here, we report on optical resonances reaching Q∼105 induced by disorder on photonic/phononic-crystal waveguides. At relatively low excitation powers (below 1mW), these cavities exhibit nonlinear effects leading to periodic (up to ∼35 MHz) oscillations of their resonant wavelength. Our system represents a test bed to study the interplay between structural complexity and material nonlinearities and their impact on localization phenomena and introduces a different functionality to the toolset of disordered photonics., This work was supported by the Spanish Ministerio de Ciencia, Innovación y Universidades (MICINN) via the Severo Ochoa Program (Grant No. SEV-2013-0295) and the project PHENTOM (Fis 2015-70862-P), as well as by the CERCA Programme/Generalitat de Catalunya, and by the European Commission in the form of the H2020 FET Open Project PHENOMEN (Grant No. 713450). G.A. is supported by a BIST Ph.D. Fellowship, and P.D.G. and D.N.-U. gratefully acknowledge support through the Ramon y Cajal fellowships No. RYC-2015-18124 and No. RYC-2014-15392, respectively, Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Nanocrystalline silicon optomechanical cavities

  • Navarro-Urrios, D.
  • Capuj, Néstor E.
  • Maire, Jeremie
  • Colombano, Martin F.
  • Jaramillo-Fernandez, Juliana
  • Chávez-Angel, Emigdio
  • Martín, Leopold L.
  • Mercadé, Laura
  • Griol, Amadeu
  • Martínez, Alejandro
  • Sotomayor Torres, C. M.
  • Ahopelto, Jouni
Silicon on insulator photonics has offered a versatile platform for the recent development of integrated optomechanical circuits. However, there are some constraints such as the high cost of the wafers and limitation to a single physical device level. In the present work we investigate nanocrystalline silicon as an alternative material for optomechanical devices. In particular, we demonstrate that optomechanical crystal cavities fabricated of nanocrystalline silicon have optical and mechanical properties enabling non-linear dynamical behaviour and effects such as thermo-optic/free-carrier-dispersion self-pulsing, phonon lasing and chaos, all at low input laser power and with typical frequencies as high as 0.3 GHz., European Commission project PHENOMEN (H2020-EU-713450), MINECO Severo Ochoa Excellence program (SEV-2013-0295), MINECO (FIS2015-70862-P, RYC-2014-15392) and CERCA Programme/Generalitat de Catalunya., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Optical modulation of coherent phonon emission in optomechanical cavities

  • Maire, Jeremie
  • Arregui, Guillermo
  • Capuj, Néstor E.
  • Colombano, Martin F.
  • Griol, Amadeu
  • Martínez, Alejandro
  • Sotomayor Torres, C. M.
  • Navarro-Urrios, D.
Optomechanical (OM) structures are well suited to study photon-phonon interactions, and they also turn out to be potential building blocks for phononic circuits and quantum computing. In phononic circuits, in which information is carried and processed by phonons, OM structures could be used as interfaces to photons and electrons thanks to their excellent coupling efficiency. Among the components required for phononic circuits, such structures could be used to create coherent phonon sources and detectors, but more complex functions remain challenging. Here, we propose and demonstrate a way to modulate the coherent phonon emission from OM crystals by a photothermal effect induced by an external laser, effectively creating a phonon switch working at ambient conditions of pressure and temperature and the working speed of which is only limited by the build-up time of the mechanical motion of the OM structure. We additionally demonstrate two other modulation schemes: modulation of harmonics in which the mechanical mode remains active but different harmonics of the optical force are used, and modulation to and from a chaotic regime. Furthermore, due to the local nature of the photothermal effect used here, we expect this method to allow us to selectively modulate the emission of any single cavity on a chip without affecting its surroundings in the absence of mechanical coupling between the structures, which is an important step toward freely controllable networks of OM phonon emitters., This work was supported by the European Comission FET Open project PHENOMEN (No. H2020-EU-713450) and the Spanish MINECO project PHENTOM (No. FIS2015-70862-P). The ICN2 is funded by the CERCA programme, the Generalitat de Catalunya, and supported by the Severo Ochoa programme of the Spanish MINECO Grant No. SEV-2013-0295. D.N.U. and M.F.C. gratefully acknowledge the support of a Ramón y Cajal postdoctoral fellowship (No. RYC-2014-15392) and a Severo Ochoa studentship, respectively., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Synchronization of optomechanical nanobeams by mechanical interaction

  • Colombano, Martin F.
  • Arregui, Guillermo
  • Capuj, Néstor E.
  • Pitanti, Alessandro
  • Maire, Jeremie
  • Griol, Amadeu
  • Garrido, Blas
  • Martínez, Alejandro
  • Sotomayor Torres, C. M.
  • Navarro-Urrios, D.
The synchronization of coupled oscillators is a phenomenon found throughout nature. Mechanical oscillators are paradigmatic examples, but synchronizing their nanoscaled versions is challenging. We report synchronization of the mechanical dynamics of a pair of optomechanical crystal cavities that, in contrast to previous works performed in similar objects, are intercoupled with a mechanical link and support independent optical modes. In this regime they oscillate in antiphase, which is in agreement with the predictions of our numerical model that considers reactive coupling. We also show how to temporarily disable synchronization of the coupled system by actuating one of the cavities with a heating laser, so that both cavities oscillate independently. Our results can be upscaled to more than two cavities and pave the way towards realizing integrated networks of synchronized mechanical oscillators., This work was supported by the European Commission project PHENOMEN (H2020-EU-713450), the Spanish Severo Ochoa Excellence program, and the MINECO project PHENTOM (FIS2015-70862-P). D. N. U., G. A., and M. F. C. gratefully acknowledge the support of a Ramón y Cajal postdoctoral fellowship (RYC-2014-15392), a BIST studentship, and a Severo Ochoa studentship, respectively., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Ferromagnetic resonance assisted optomechanical magnetometer

  • Colombano, Martin F.
  • Arregui, Guillermo
  • Bonell, Fréderic
  • Capuj, Néstor E.
  • Chávez-Angel, Emigdio
  • Pitanti, Alessandro
  • Valenzuela, Sergio O.
  • Sotomayor Torres, C. M.
  • Navarro-Urrios, D.
  • Costache, Marius V.
The resonant enhancement of mechanical and optical interaction in optomechanical cavities enables their use as extremely sensitive displacement and force detectors. In this Letter, we demonstrate a hybrid magnetometer that exploits the coupling between the resonant excitation of spin waves in a ferromagnetic insulator and the resonant excitation of the breathing mechanical modes of a glass microsphere deposited on top. The interaction is mediated by magnetostriction in the ferromagnetic material and the consequent mechanical driving of the microsphere. The magnetometer response thus relies on the spectral overlap between the ferromagnetic resonance and the mechanical modes of the sphere, leading to a peak sensitivity of 850pTHz−1/2 at 206 MHz when the overlap is maximized. By externally tuning the ferromagnetic resonance frequency with a static magnetic field, we demonstrate sensitivity values at resonance around a few nT Hz−1/2 up to the gigahertz range. Our results show that our hybrid system can be used to build a high-speed sensor of oscillating magnetic fields., This work was supported by the Spanish Severo Ochoa Excellence program. D. N. U. gratefully acknowledges the support of a Ramón y Cajal postdoctoral fellowship (RYC-2014-15392) and the Ministry of Science, Innovation and Universities (PGC2018-094490-B-C22). M. V. C. acknowledges support from the Spanish Ministry of Economy and Competitiveness, MINECO (under Contract No. FIS2015-62641-ERC). M. F. C. acknowledges support of a Severo Ochoa studentship. G. A. acknowledges support of a BIST studentship., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

High-frequency mechanical excitation of a silicon nanostring with piezoelectric aluminum nitride layers

  • Pitanti, Alessandro
  • Makkonen, Tapani
  • Colombano, Martin F.
  • Zanotto, Simone
  • Vicarelli, Leonardo
  • Cecchini, Marco
  • Griol, Amadeu
  • Navarro-Urrios, D.
  • Sotomayor Torres, C. M.
  • Martínez, Alejandro
  • Ahopelto, Jouni
A strong trend for quantum-based technologies and applications follows the avenue of combining different platforms to exploit their complementary technological and functional advantages. Micro and nanomechanical devices are particularly suitable for hybrid integration due to the ease of fabrication at multiscales and their pervasive coupling with electrons and photons. Here, we report on a nanomechanical technological platform where a silicon chip is combined with an aluminum nitride layer. Exploiting the AlN piezoelectricity, surface acoustic waves (SAWs) are injected in the Si layer where the material has been locally patterned and etched to form a suspended nanostring. Characterizing the nanostring vertical displacement induced by the SAW, we find an external excitation peak efficiency in excess of 500 pm/V at 1-GHz mechanical frequency. Exploiting the long-term expertise in silicon photonic and electronic devices as well as the SAW robustness and versatility, our technological platform represents a candidate for hybrid quantum systems., This work is supported by the FET-Open PHENOMEN project (GA 713450). D.N.U. gratefully acknowledges funding from a Ramon y Cajal postdoctoral fellowship (RYC-2014-15392)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Properties of nanocrystalline silicon probed by optomechanics

  • Navarro-Urrios, D.
  • Colombano, Martin F.
  • Maire, Jeremie
  • Chávez-Angel, Emigdio
  • Arregui, Guillermo
  • Capuj, Néstor E.
  • Devos, Arnaud
  • Griol, Amadeu
  • Bellières, Laurent
  • Martínez, Alejandro
  • Grigoras, Kestutis
  • Häkkinen, Teija
  • Saarilahti, Jaakko
  • Makkonen, Tapani
  • Sotomayor Torres, C. M.
  • Ahopelto, Jouni
Nanocrystalline materials exhibit properties that can differ substantially from those of their single crystal counterparts. As such, they provide ways to enhance and optimize their functionality for devices and applications. Here, we report on the optical, mechanical and thermal properties of nanocrystalline silicon probed by means of optomechanical nanobeams to extract information of the dynamics of optical absorption, mechanical losses, heat generation and dissipation. The optomechanical nanobeams are fabricated using nanocrystalline films prepared by annealing amorphous silicon layers at different temperatures. The resulting crystallite sizes and the stress in the films can be controlled by the annealing temperature and time and, consequently, the properties of the films can be tuned relatively freely, as demonstrated here by means of electron microscopy and Raman scattering. We show that the nanocrystallite size and the volume fraction of the grain boundaries play a key role in the dissipation rates through nonlinear optical and thermal processes. Promising optical (13,000) and mechanical (1700) quality factors were found in the optomechanical cavity realized in the nanocrystalline Si resulting from annealing at 950°C. The enhanced absorption and recombination rates via the intragap states and the reduced thermal conductivity boost the potential to exploit these nonlinear effects in applications including Nanoelectromechanical systems (NEMS), phonon lasing and chaos-based devices., The following support is gratefully acknowledged: the European Commission project PHENOMEN (H2020-EU-FET Open GA no. 713450), the Spanish Severo Ochoa Excellence program (SEV-2017-0706), CMST and ECA: the Spanish MICINN project SIP (PGC2018-101743-B-I00), DNU and AM: the Spanish MICINN project PGC2018-094490-B-C22. DNU holds a Ramón y Cajal postdoctoral fellowship (RYC-2014-15392); MFC and GA hold a S. Ochoa and a M. S. Curie COFUND BIST postgraduate studentship, respectively., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Thermal Properties of Nanocrystalline Silicon Nanobeams

  • Maire, Jeremie
  • Chávez-Angel, Emigdio
  • Arregui, Guillermo
  • Colombano, Martin F.
  • Capuj, Néstor E.
  • Griol, Amadeu
  • Martínez, Alejandro
  • Navarro-Urrios, D.
  • Ahopelto, Jouni
  • Sotomayor Torres, C. M.
Controlling thermal energy transfer at the nanoscale and thermal properties has become critically important in many applications since it often limits device performance. In this study, the effects on thermal conductivity arising from the nanoscale structure of free-standing nanocrystalline silicon films and the increasing surface-to-volume ratio when fabricated into suspended optomechanical nanobeams are studied. Thermal transport and elucidate the relative impact of different grain size distributions and geometrical dimensions on thermal conductivity are characterized. A micro time-domain thermoreflectance method to study free-standing nanocrystalline silicon films and find a drastic reduction in the thermal conductivity, down to values below 10 W m–1 K–1 is used, with a stronger decrease for smaller grains. In optomechanical nanostructures, this effect is smaller than in membranes due to the competition of surface scattering in decreasing thermal conductivity. Finally, a novel versatile contactless characterization technique that can be adapted to any structure supporting a thermally shifted optical resonance is introduced. The thermal conductivity data agrees quantitatively with the thermoreflectance measurements. This study opens the way to a more generalized thermal characterization of optomechanical cavities and to create hot-spots with engineered shapes at the desired position in the structures as a means to study thermal transport in coupled photon-phonon structures., This work was supported by the European Commission FET Open project PHENOMEN (G.A. Nr. 713450). ICN2 was supported by the S. Ochoa program from the Spanish Research Agency (AEI, grant no. SEV-2017-0706) and by the CERCA Programme / Generalitat de Catalunya. ICN2 authors acknowledge the support from the Spanish MICINN project SIP (PGC2018-101743-B-I00). D.N.U. and M.F.C. acknowledge the support of a Ramón y Cajal postdoctoral fellowship (RYC-2014-15392) and a Severo Ochoa studentship, respectively. E.C.A. acknowledges financial support from the EU FET Open Project NANOPOLY. (GA 829061). A.M. acknowledges support from Ministerio de Ciencia, Innovación y Universidades (grant PGC2018-094490-B, PRX18/00126) and Generalitat Valenciana (grants PROMETEO/2019/123, and IDIFEDER/2018/033).
Dipòsit Digital de Documents de la UAB
Publication Artículo científico (JournalArticle)

Optomechanical coupling in the Anderson-localization regime

  • García Fernández, Pedro David|||0000-0002-3422-178X
  • Bericat-Vadell, R.
  • Arregui Bravo, Guillermo|||0000-0002-6458-5277
  • Navarro Urrios, Daniel|||0000-0001-9055-1583
  • Colombano Sosa, Martin|||0000-0002-2003-8597
  • Alzina, Francesc|||0000-0002-7082-0624
  • Sotomayor Torres, Clivia M.|||0000-0001-9986-2716
Optomechanical crystals, purposely designed and fabricated semiconductor nanostructures, are used to enhance the coupling between the electromagnetic field and the mechanical vibrations of matter at the nanoscale. However, in real optomechanical crystals, imperfections open extra channels where the transfer of energy is lost, reducing the optomechanical coupling efficiency. Here, we quantify the role of disorder in a paradigmatic one-dimensional optomechanical crystal with full phononic and photonic band gaps. We show how disorder can be exploited as a resource to enhance the optomechanical coupling beyond engineered structures, thus providing a new tool set for optomechanics.
Dipòsit Digital de Documents de la UAB
Publication Artículo científico (JournalArticle)

Mechanical oscillations in lasing microspheres

  • Toncelli, Alessandra
  • Capuj, Nestor Eduardo|||0000-0002-9042-2041
  • Garrido Fernández, Blas
  • Sledzinska, Marianna|||0000-0001-8592-1121
  • Sotomayor Torres, Clivia M.|||0000-0001-9986-2716
  • Tredicucci, Alessandro|||0000-0003-3619-3011
  • Navarro Urrios, Daniel|||0000-0001-9055-1583
We investigate the feasibility of activating coherent mechanical oscillations in lasing microspheres by modulating the laser emission at a mechanical eigenfrequency. To this aim, 1.5%Nd3+:Barium- Titanium-Silicate microspheres with diameters around 50 lm were used as high quality factor (Q>106) whispering gallery mode lasing cavities. We have implemented a pump-and-probe technique in which the pump laser used to excite the Nd3+ ions is focused on a single microsphere with a microscope objective and a probe laser excites a specific optical mode with the evanescent field of a tapered fibre. The studied microspheres show monomode and multi-mode lasing action, which can be modulated in the best case up to 10 MHz. We have optically transduced thermally activated mechanical eigenmodes appearing in the 50-70MHz range, the frequency of which decreases with increasing the size of the microspheres. In a pump-and-probe configuration, we observed modulation of the probe signal up to the maximum pump modulation frequency of our experimental setup, i.e., 20 MHz. This modulation decreases with frequency and is unrelated to lasing emission, pump scattering, or thermal effects. We associate this effect to free-carrier-dispersion induced by multiphoton pump light absorption. On the other hand, we conclude that, in our current experimental conditions, it was not possible to resonantly excite the mechanical modes. Finally, we discuss on how to overcome these limitations by increasing the modulation frequency of the lasing emission and decreasing the frequency of the mechanical eigenmodes displaying a strong degree of optomechanical coupling.
Dipòsit Digital de Documents de la UAB
Publication Artículo científico (JournalArticle)

Nonlinear dynamics and chaos in an optomechanical beam

  • Navarro Urrios, Daniel|||0000-0001-9055-1583
  • Capuj, Nestor Eduardo|||0000-0002-9042-2041
  • Colombano Sosa, Martin|||0000-0002-2003-8597
  • García Fernández, Pedro David|||0000-0002-3422-178X
  • Sledzinska, Marianna|||0000-0001-8592-1121
  • Alzina, Francesc|||0000-0002-7082-0624
  • Griol, Amadeu|||0000-0002-5428-5713
  • Martínez, Alejandro|||0000-0001-5448-0140
  • Sotomayor Torres, Clivia M.|||0000-0001-9986-2716
Optical nonlinearities, such as thermo-optic mechanisms and free-carrier dispersion, are often considered unwelcome effects in silicon-based resonators and, more specifically, optomechanical cavities, since they affect, for instance, the relative detuning between an optical resonance and the excitation laser. Here, we exploit these nonlinearities and their intercoupling with the mechanical degrees of freedom of a silicon optomechanical nanobeam to unveil a rich set of fundamentally different complex dynamics. By smoothly changing the parameters of the excitation laser we demonstrate accurate control to activate two- A nd four-dimensional limit cycles, a period-doubling route and a six-dimensional chaos. In addition, by scanning the laser parameters in opposite senses we demonstrate bistability and hysteresis between two- A nd four-dimensional limit cycles, between different coherent mechanical states and between four-dimensional limit cycles and chaos. Our findings open new routes towards exploiting silicon-based optomechanical photonic crystals as a versatile building block to be used in neurocomputational networks and for chaos-based applications.
Dipòsit Digital de Documents de la UAB
Publication Artículo científico (JournalArticle)

Optical modulation of coherent phonon emission in optomechanical cavities

  • Maire, Jeremie|||0000-0002-9921-4804
  • Arregui Bravo, Guillermo|||0000-0002-6458-5277
  • Capuj, Nestor Eduardo|||0000-0002-9042-2041
  • Colombano Sosa, Martin|||0000-0002-2003-8597
  • Griol, Amadeu|||0000-0002-5428-5713
  • Martínez, Alejandro|||0000-0001-5448-0140
  • Sotomayor Torres, Clivia M.|||0000-0001-9986-2716
  • Navarro Urrios, Daniel|||0000-0001-9055-1583
Optomechanical (OM) structures are well suited to study photon-phonon interactions, and they also turn out to be potential building blocks for phononic circuits and quantum computing. In phononic circuits, in which information is carried and processed by phonons, OM structures could be used as interfaces to photons and electrons thanks to their excellent coupling efficiency. Among the components required for phononic circuits, such structures could be used to create coherent phonon sources and detectors, but more complex functions remain challenging. Here, we propose and demonstrate a way to modulate the coherent phonon emission from OM crystals by a photothermal effect induced by an external laser, effectively creating a phonon switch working at ambient conditions of pressure and temperature and the working speed of which is only limited by the build-up time of the mechanical motion of the OM structure. We additionally demonstrate two other modulation schemes: modulation of harmonics in which the mechanical mode remains active but different harmonics of the optical force are used, and modulation to and from a chaotic regime. Furthermore, due to the local nature of the photothermal effect used here, we expect this method to allow us to selectively modulate the emission of any single cavity on a chip without affecting its surroundings in the absence of mechanical coupling between the structures, which is an important step toward freely controllable networks of OM phonon emitters.
Dipòsit Digital de Documents de la UAB
Publication Artículo científico (JournalArticle)

Nanocrystalline silicon optomechanical cavities

  • Navarro Urrios, Daniel|||0000-0001-9055-1583
  • Capuj, Nestor Eduardo|||0000-0002-9042-2041
  • Maire, Jeremie|||0000-0002-9921-4804
  • Colombano Sosa, Martin|||0000-0002-2003-8597
  • Jaramillo Fernández, Juliana|||0000-0002-4787-3904
  • Chávez Ángel, Emigdio|||0000-0002-9783-0806
  • Martin, L. L.
  • Mercadé, L.
  • Griol, Amadeu|||0000-0002-5428-5713
  • Martínez, Alejandro|||0000-0001-5448-0140
  • Sotomayor Torres, Clivia M.|||0000-0001-9986-2716
  • Ahopelto, Jouni|||0000-0003-3372-6097
Silicon on insulator photonics has offered a versatile platform for the recent development of integrated optomechanical circuits. However, there are some constraints such as the high cost of the wafers and limitation to a single physical device level. In the present work we investigate nanocrystalline silicon as an alternative material for optomechanical devices. In particular, we demonstrate that optomechanical crystal cavities fabricated of nanocrystalline silicon have optical and mechanical properties enabling non-linear dynamical behaviour and effects such as thermo-optic/free-carrier-dispersion self-pulsing, phonon lasing and chaos, all at low input laser power and with typical frequencies as high as 0.3 GHz.
Dipòsit Digital de Documents de la UAB
Publication Artículo científico (JournalArticle)

Synchronization of Optomechanical Nanobeams by Mechanical Interaction

  • Colombano Sosa, Martin|||0000-0002-2003-8597
  • Arregui Bravo, Guillermo|||0000-0002-6458-5277
  • Capuj, Nestor Eduardo|||0000-0002-9042-2041
  • Pitanti, Alessandro|||0000-0002-7027-0300
  • Maire, Jeremie|||0000-0002-9921-4804
  • Griol, Amadeu|||0000-0002-5428-5713
  • Garrido Fernández, Blas
  • Martínez, Alejandro|||0000-0001-5448-0140
  • Sotomayor Torres, Clivia M.|||0000-0001-9986-2716
  • Navarro Urrios, Daniel|||0000-0001-9055-1583
The synchronization of coupled oscillators is a phenomenon found throughout nature. Mechanical oscillators are paradigmatic examples, but synchronizing their nanoscaled versions is challenging. We report synchronization of the mechanical dynamics of a pair of optomechanical crystal cavities that, in contrast to previous works performed in similar objects, are intercoupled with a mechanical link and support independent optical modes. In this regime they oscillate in antiphase, which is in agreement with the predictions of our numerical model that considers reactive coupling. We also show how to temporarily disable synchronization of the coupled system by actuating one of the cavities with a heating laser, so that both cavities oscillate independently. Our results can be upscaled to more than two cavities and pave the way towards realizing integrated networks of synchronized mechanical oscillators.
Dipòsit Digital de Documents de la UAB
Publication Artículo científico (JournalArticle)

Record low thermal conductivity of polycrystalline MoS2 films, tuning the thermal conductivity by grain orientation

  • Sledzinska, Marianna|||0000-0001-8592-1121
  • Quey, Romain|||0000-0002-1593-8179
  • Mortazavi, Bohayra|||0000-0003-3031-5057
  • Graczykowski, Bartlomiej|||0000-0003-4787-8622
  • Placidi, M.
  • Saleta Reig, David|||0000-0003-3189-2331
  • Navarro Urrios, Daniel|||0000-0001-9055-1583
  • Alzina, Francesc|||0000-0002-7082-0624
  • Colombo, Luciano|||0000-0001-5335-4652
  • Roche, Stephan|||0000-0003-0323-4665
  • Sotomayor Torres, Clivia M.|||0000-0001-9986-2716
We report a record low thermal conductivity in polycrystalline MoS obtained for ultrathin films with varying grain sizes and orientations. By optimizing the sulfurization parameters of nanometer-thick Mo layers, five MoS films containing a combination of horizontally and vertically oriented grains, with respect to the bulk (001) monocrystal, were grown. From transmission electron microscopy, the average grain size, typically below 10 nm, and proportion of differently oriented grains were extracted. The thermal conductivity of the suspended samples was extracted from a Raman laser-power-dependent study, and the lowest value of thermal conductivity of 0.27 W m K, which reaches a similar value as that of Teflon, is obtained in a polycrystalline sample formed by a combination of horizontally and vertically oriented grains in similar proportion. Analysis by means of molecular dynamics and finite element method simulations confirm that such a grain arrangement leads to lower grain boundary conductance. We discuss the possible use of these thermal insulating films in the context of electronics and thermoelectricity.
Dipòsit Digital de Documents de la UAB
Publication Artículo científico (JournalArticle)

Injection locking in an optomechanical coherent phonon source

  • Arregui Bravo, Guillermo|||0000-0002-6458-5277
  • Colombano Sosa, Martin|||0000-0002-2003-8597
  • Maire, Jeremie|||0000-0002-9921-4804
  • Pitanti, Alessandro|||0000-0002-7027-0300
  • Capuj, Nestor Eduardo|||0000-0002-9042-2041
  • Griol, Amadeu|||0000-0002-5428-5713
  • Martínez, Alejandro|||0000-0001-5448-0140
  • Sotomayor Torres, Clivia M.|||0000-0001-9986-2716
  • Navarro Urrios, Daniel|||0000-0001-9055-1583
Spontaneous locking of the phase of a coherent phonon source to an external reference is demonstrated in a deeply sideband-unresolved optomechanical system. The high-amplitude mechanical oscillations are driven by the anharmonic modulation of the radiation pressure force that result from an absorption-mediated free-carrier/temperature limit cycle, i.e., self-pulsing. Synchronization is observed when the pump laser driving the mechanical oscillator to a self-sustained state is modulated by a radiofrequency tone. We employ a pump-probe phonon detection scheme based on an independent optical cavity to observe only the mechanical oscillator dynamics. The lock range of the oscillation frequency, i.e., the Arnold tongue, is experimentally determined over a range of external reference strengths, evidencing the possibility to tune the oscillator frequency for a range up to 350 kHz. The stability of the coherent phonon source is evaluated via its phase noise, with a maximum achieved suppression of 44 dBc/Hz at 1 kHz offset for a 100 MHz mechanical resonator. Introducing a weak modulation in the excitation laser reveals as a further knob to trigger, control and stabilize the dynamical solutions of self-pulsing based optomechanical oscillators, thus enhancing their potential as acoustic wave sources in a single-layer silicon platform.
Dipòsit Digital de Documents de la UAB
Publication Artículo científico (JournalArticle)

Properties of nanocrystalline silicon probed by optomechanics

  • Navarro Urrios, Daniel|||0000-0001-9055-1583
  • Colombano Sosa, Martin|||0000-0002-2003-8597
  • Maire, Jeremie|||0000-0002-9921-4804
  • Chávez Ángel, Emigdio|||0000-0002-9783-0806
  • Arregui Bravo, Guillermo|||0000-0002-6458-5277
  • Capuj, Nestor Eduardo|||0000-0002-9042-2041
  • Devos, Arnaud
  • Griol, Amadeu|||0000-0002-5428-5713
  • Bellieres, Laurent
  • Martínez, Alejandro|||0000-0001-5448-0140
  • Grigoras, Kestutis
  • Häkkinen, Teija
  • Saarilahti, Jaakko
  • Makkonen, Tapani
  • Sotomayor Torres, Clivia M.|||0000-0001-9986-2716
  • Ahopelto, Jouni|||0000-0003-3372-6097
Nanocrystalline materials exhibit properties that can differ substantially from those of their single crystal counterparts. As such, they provide ways to enhance and optimize their functionality for devices and applications. Here, we report on the optical, mechanical and thermal properties of nanocrystalline silicon probed by means of optomechanical nanobeams to extract information of the dynamics of optical absorption, mechanical losses, heat generation and dissipation. The optomechanical nanobeams are fabricated using nanocrystalline films prepared by annealing amorphous silicon layers at different temperatures. The resulting crystallite sizes and the stress in the films can be controlled by the annealing temperature and time and, consequently, the properties of the films can be tuned relatively freely, as demonstrated here by means of electron microscopy and Raman scattering. We show that the nanocrystallite size and the volume fraction of the grain boundaries play a key role in the dissipation rates through nonlinear optical and thermal processes. Promising optical (13,000) and mechanical (1700) quality factors were found in the optomechanical cavity realized in the nanocrystalline Si resulting from annealing at 950°C. The enhanced absorption and recombination rates via the intragap states and the reduced thermal conductivity boost the potential to exploit these nonlinear effects in applications including Nanoelectromechanical systems (NEMS), phonon lasing and chaos-based devices.
Dipòsit Digital de Documents de la UAB
Publication Artículo científico (JournalArticle)

Thermal properties of nanocrystalline silicon nanobeams

  • Maire, Jeremie|||0000-0002-9921-4804
  • Chávez Ángel, Emigdio|||0000-0002-9783-0806
  • Arregui Bravo, Guillermo|||0000-0002-6458-5277
  • Colombano Sosa, Martin|||0000-0002-2003-8597
  • Capuj, Nestor Eduardo|||0000-0002-9042-2041
  • Griol, Amadeu|||0000-0002-5428-5713
  • Martínez, Alejandro|||0000-0001-5448-0140
  • Navarro Urrios, Daniel|||0000-0001-9055-1583
  • Ahopelto, Jouni|||0000-0003-3372-6097
  • Sotomayor Torres, Clivia M.|||0000-0001-9986-2716
Controlling thermal energy transfer at the nanoscale and thermal properties has become critically important in many applications since it often limits device performance. In this study, the effects on thermal conductivity arising from the nanoscale structure of free-standing nanocrystalline silicon films and the increasing surface-to-volume ratio when fabricated into suspended optomechanical nanobeams are studied. Thermal transport and elucidate the relative impact of different grain size distributions and geometrical dimensions on thermal conductivity are characterized. A micro time-domain thermoreflectance method to study free-standing nanocrystalline silicon films and find a drastic reduction in the thermal conductivity, down to values below 10 W m K is used, with a stronger decrease for smaller grains. In optomechanical nanostructures, this effect is smaller than in membranes due to the competition of surface scattering in decreasing thermal conductivity. Finally, a novel versatile contactless characterization technique that can be adapted to any structure supporting a thermally shifted optical resonance is introduced. The thermal conductivity data agrees quantitatively with the thermoreflectance measurements. This study opens the way to a more generalized thermal characterization of optomechanical cavities and to create hot-spots with engineered shapes at the desired position in the structures as a means to study thermal transport in coupled photon-phonon structures.
Dipòsit Digital de Documents de la UAB
Publication Artículo preliminar (WorkingPaper)

Heat dissipation in few-layer MoS2 and MoS2/hBN heterostructure

  • Arrighi, Aloïs|||0000-0002-9774-852X
  • Del Corro, Elena|||0000-0001-6452-9139
  • Navarro Urrios, Daniel|||0000-0001-9055-1583
  • Costache, Marius Vasile|||0000-0001-7432-6175
  • Sierra, Juan F.|||0000-0002-5438-0534
  • Watanabe, Kenji|||0000-0003-3701-8119
  • Taniguchi, Takashi|||0000-0002-1467-3105
  • Garrido, Jose|||0000-0001-5621-1067
  • Valenzuela, Sergio O.|||0000-0002-4632-8891
  • Sotomayor Torres, Clivia M.|||0000-0001-9986-2716
  • Sledzinska, Marianna|||0000-0001-8592-1121
State-of-the-art fabrication and characterization techniques have been employed to measure the thermal conductivity of suspended, single-crystalline MoS2 and MoS2/hBN heterostructures. Two-laser Raman scattering thermometry was used combined with real time measurements of the absorbed laser power, which allowed us to determine the thermal conductivities without any assumptions. Measurements on MoS2 layers with thicknesses of 5 and 14 exhibit thermal conductivity in the range between 12 and 24 Wm-1K-1. Additionally, after determining the thermal conductivity of a selected MoS2 sample, an hBN flake was transferred onto it and the effective thermal conductivity of the heterostructure was subsequently measured. Remarkably, despite that the thickness of the hBN layer was less than a third of the thickness of the MoS2 layer, the heterostructure showed an almost eight-fold increase in the thermal conductivity, being able to dissipate more than 10 times the laser power without any visible sign of damage. These results are consistent with a high thermal interface conductance between MoS2 and hBN and an efficient in-plane heat spreading driven by hBN. Indeed, we estimate G 70 MWm-2K-1 which is significantly higher than previously reported values. Our work therefore demonstrates that the insertion of hBN layers in potential MoS2 based devices holds the promise for efficient thermal management.