Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 44
Encontrada(s) 1 página(s)

TECNALIA Publications
Publicación Artículo científico (JournalArticle)

PBI mixed matrix hollow fiber membrane: Influence of ZIF-8 filler over H2/CO2 separation performance at high temperature and pressure: Influence of ZIF-8 filler over H2/CO2 separation performance at high temperature and pressure

  • Etxeberria-Benavides, Miren
  • Johnson, Timothy
  • Cao, Shuai
  • Zornoza, Beatriz
  • Coronas, Joaquín
  • Sanchez-Lainez, Javier
  • Sabetghadam, Anahid
  • Liu, Xinlei
  • Andres-Garcia, Eduardo
  • Kapteijn, Freek
  • Gascon, Jorge
  • David, Oana
High performance and commercially attractive mixed-matrix membranes were developed for H2/CO2 separation via a scalable hollow fiber spinning process. Thin (~300 nm) and defect-free selective layers were successfully created with a uniform distribution of the nanosized (~60 nm) zeolitic-imidazole framework (ZIF-8) filler within the polymer (polybenzimidazole, PBI) matrix. These membranes were able to operate at high temperature (150 °C) and pressure (up to 30 bar) process conditions required in treatment of pre-combustion and syngas process gas streams. Compared with neat PBI hollow fibers, filler incorporation into the polymer matrix leads to a strong increase in H2 permeance from 65 GPU to 107 GPU at 150 °C and 7 bar, while the ideal H2/CO2 selectivity remained constant at 18. For mixed gas permeation, there is competition between H2 and CO2 transport inside ZIF-8 structure. Adsorption of CO2 in the nanocavities of the filler suppresses the transport of the faster permeating H2 and consequently decreases the H2 permeance with total feed pressure down to values equal to the pure PBI hollow fibers for the end pressure of 30 bar. Therefore, the improvement of fiber performance for gas separation with filler addition is compromised at high operating feed pressures, which emphasizes the importance of membrane evaluation under relevant process conditions.
TECNALIA Publications
Publicación Artículo científico (JournalArticle)

Metal-organic framework based mixed matrix membranes: a solution for highly efficient CO2 capture?: A solution for highly efficient CO2 capture?

  • Seoane, Beatriz
  • Coronas, Joaquin
  • Gascon, Ignacio
  • Etxeberria-Benavides, Miren
  • Karvan, Oguz
  • Caro, Juergen
  • Kapteijn, Freek
  • Gascon, Jorge
  • Caro, Jürgen
The field of metal-organic framework based mixed matrix membranes (M(4)s) is critically reviewed, with special emphasis on their application in CO2 capture during energy generation. After introducing the most relevant parameters affecting membrane performance, we define targets in terms of selectivity and productivity based on existing literature on process design for pre- and post-combustion CO2 capture. Subsequently, the state of the art in M(4)s is reviewed against these targets. Because final application of these membranes will only be possible if thin separation layers can be produced, the latest advances in the manufacture of M-4 hollow fibers are discussed. Finally, the recent efforts in understanding the separation performance of these complex composite materials and future research directions are outlined.
TECNALIA Publications
Publicación Artículo científico (JournalArticle)

Fabrication of Defect-Free P84® Polyimide Hollow Fiber for Gas Separation: Pathway to Formation of Optimized Structure: Pathway to formation of optimized structure

  • Etxeberria-Benavides, Miren
  • Karvan, Oguz
  • Kapteijn, Freek
  • Gascon, Jorge
  • David, Oana
The elimination of the additional defect healing post-treatment step in asymmetric hollow fiber manufacturing would result in a significant reduction in membrane production cost. However, obtaining integrally skinned polymeric asymmetric hollow fiber membranes with an ultrathin and defect-free selective layer is quite challenging. In this study, P84® asymmetric hollow fiber membranes with a highly thin (~56 nm) defect-free skin were successfully fabricated by fine tuning the dope composition and spinning parameters using volatile additive (tetrahydrofuran, THF) as key parameters. An extensive experimental and theoretical study of the influence of volatile THF addition on the solubility parameter of the N-methylpyrrolidone/THF solvent mixture was performed. Although THF itself is not a solvent for P84®, in a mixture with a good solvent for the polymer, like N-Methyl-2-pyrrolidone (NMP), it can be dissolved at high THF concentrations (NMP/THF ratio > 0.52). The as-spun fibers had a reproducible ideal CO2/N2 selectivity of 40, and a CO2 permeance of 23 GPU at 35 °C. The fiber production can be scaled-up with retention of the selectivity.
TECNALIA Publications
Publicación Artículo científico (JournalArticle)

High performance mixed matrix membranes (MMMs) composed of ZIF-94 filler and 6FDA-DAM polymer

  • Etxeberria-Benavides, Miren
  • David, Oana
  • Johnson, Timothy
  • Łozińska, Magdalena M.
  • Orsi, Angelica
  • Wright, Paul A.
  • Mastel, Stefan
  • Hillenbrand, Rainer
  • Kapteijn, Freek
  • Gascon, Jorge
Carbon capture and storage (CCS) using membranes for the separation of CO2 holds great promise for the reduction of atmospheric CO2 emissions from fuel combustion and industrial processes. Among the different process outlines, post-combustion CO2 capture could be easily implemented in existing power plants. However, for this technology to become viable, new membrane materials have to be developed. In this article we present the development of high performance mixed matrix membranes (MMMs) composed of ZIF-94 filler and 6FDADAM polymer matrix. The CO2/N2 separation performance was evaluated by mixed gas tests (15CO2:85N2) at 25 °C and 1–4 bar transmembrane pressure difference. The CO2 membrane permeability was increased by the addition of the ZIF-94 particles, maintaining a constant CO2/N2 selectivity of ~22. The largest increase in CO2 permeability of ~ 200% was observed for 40 wt% ZIF-94 loading, reaching the highest permeability (2310 Barrer) at similar selectivity among 6FDA-DAM MMMs reported in literature. For the first time, the ZIF-94 metal organic framework crystals with particle size smaller than 500 nm were synthesized using nonhazardous solvent (tetrahydrofuran and methanol) instead of dimethylformamide (DMF) in a scalable process. Membranes were characterized by three non-invasive image techniques, i.e. SEM, AFM and nanoscale infrared imaging by scattering-type scanning near-field optical microscopy (s-SNOM). The combination of these techniques demonstrates a very good dispersion and interaction of the filler in the polymer layer, even at very high loadings.
RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

Beyond the H2/CO2 upper bound: one-step crystallization and separation of nano-sized ZIF-11 by centrifugation and its application in mixed matrix membranes

  • Sánchez-Laínez, Javier
  • Zornoza, Beatriz
  • Mayoral, Álvaro
  • Berenguer-Murcia, Ángel
  • Cazorla-Amorós, Diego
  • Téllez, Carlos
  • Coronas, Joaquín
  • Berenguer-Murcia, Ángel|||/items/ce71666d-8c9c-47fa-b876-397de66a9989
  • Cazorla-Amorós, Diego|||/items/bab354fe-ec79-49e0-a4f3-5288ee396750
The synthesis of nano-sized ZIF-11 with an average size of 36 ± 6 nm is reported. This material has been named nano-zeolitic imidazolate framework-11 (nZIF-11). It has the same chemical composition and thermal stability and analogous H2 and CO2 adsorption properties to the conventional microcrystalline ZIF-11 (i.e. 1.9 ± 0.9 μm). nZIF-11 has been obtained following the centrifugation route, typically used for solid separation, as a fast new technique (pioneering for MOFs) for obtaining nanomaterials where the temperature, time and rotation speed can easily be controlled. Compared to the traditional synthesis consisting of stirring + separation, the reaction time was lowered from several hours to a few minutes when using this centrifugation synthesis technique. Employing the same reaction time (2, 5 or 10 min), micro-sized ZIF-11 was obtained using the traditional synthesis while nano-scale ZIF-11 was achieved only by using centrifugation synthesis. The small particle size obtained for nZIF-11 allowed the use of the wet MOF sample as a colloidal suspension stable in chloroform. This helped to prepare mixed matrix membranes (MMMs) by direct addition of the membrane polymer (polyimide Matrimid®) to the colloidal suspension, avoiding particle agglomeration resulting from drying. The MMMs were tested for H2/CO2 separation, improving the pure polymer membrane performance, with permeation values of 95.9 Barrer of H2 and a H2/CO2 separation selectivity of 4.4 at 35 °C. When measured at 200 °C, these values increased to 535 Barrer and 9.1.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

The fabrication of ultrathin films and their gas separation performance from polymers of intrinsic microporosity with two-dimensional (2D) and three-dimensional (3D) chain conformations

  • Benito, Javier
  • Vidal, Julio
  • Sánchez-Laínez, Javier
  • Zornoza, Beatriz
  • Téllez, Carlos
  • Martín, Santiago
  • Msayib, Kadhum J.
  • Comesaña-Gándara, Bibiana
  • McKeown, Neil B.
  • Coronas, Joaquín
  • Gascón, Ignacio
The expansion of the use of polymeric membranes in gas separation requires the development of membranes based on new polymers with improved properties and their assessment under real operating conditions. In particular, the fabrication of ultrathin films of high performance polymers that can be used as the selective layer in composite membranes will allow large reductions in the amount of the expensive polymer used and, hence, the cost of membrane fabrication. In this contribution, two polymers of intrinsic microporosity (PIMs) with very different chain configurations (two-dimensional, 2D, chains or conventional contorted three-dimensional, 3D, conformation) have been compared in their ability to form ultrathin films, showing the relevance of polymer design to obtain compact and defect-free films. Monolayers of the 2D polymer PIM-TMN-Trip can be efficiently deposited onto poly[1-(trimethylsilyl)-1-propyne] (PTMSP) to obtain composite membranes with a CO2/N2 selectivity similar to that of the corresponding thick membranes of the same PIM using only a small fraction of the selective polymer (less than 0.1%)., The research leading to these results has received funding from the European Community Seventh Framework Program (EU PF7) (FP7/2007-2013), under grant agreement number 608490, project M4CO2. Financial support from the Spanish MINECO (Ministry of Economy and Business) and FEDER (European Regional Development Fund) (MAT2016-77290-R), the Aragón Government (E31_17R and T43_17R) and the ESF is gratefully acknowledged. J. S.-L. thanks the Spanish Education Ministry Program FPU2014 for his PhD grant, Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Ultrathin composite polymeric membranes for CO2 /N2 separation with minimum thickness and high CO2 permeance

  • Benito, Javier
  • Sánchez-Laínez, Javier
  • Zornoza, Beatriz
  • Martín, Santiago
  • Carta, Mariolino
  • Malpass-Evans, Richard
  • Téllez, Carlos
  • McKeown, Neil B.
  • Coronas, Joaquín
  • Gascón, Ignacio
The use of ultrathin films as selective layers in composite membranes offers significant advantages in gas separation for increasing productivity while reducing the membrane size and energy costs. In this contribution, composite membranes have been obtained by the successive deposition of approximately 1 nm thick monolayers of a polymer of intrinsic microporosity (PIM) on top of dense membranes of the ultra-permeable poly[1-(trimethylsilyl)-1-propyne] (PTMSP). The ultrathin PIM films (30 nm in thickness) demonstrate CO2 permeance up to seven times higher than dense PIM membranes using only 0.04 % of the mass of PIM without a significant decrease in CO2 /N2 selectivity., The research leading to these results has received funding from the EU FP7 Programme (FP7/2007–2013), under grant agreement number 608490, project M4CO2, Spanish MINECO and FEDER (MAT2016-77290-R) and the Aragon Government (T05 and E54). J. S.-L. thanks the Spanish Education Ministry Program FPU2014 for a Ph.D. grant., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Ultrathin hydrophobic films based on the metal organic framework UiO-66-COOH(Zr)

  • Andrés, Miguel A.
  • Sicard, Clemence
  • Serre, Christian
  • Roubeau, Olivier
  • Gascón, Ignacio
This work reports on the fabrication, optimization and characterization of ultrathin films containing submicrometer particles (sMPs) of the hydrophilic and water stable UiO-66-COOH(Zr) metal organic framework (MOF). MOF particles of ≈200 nm have been synthesized and assembled at the air–water interface by the Langmuir–Blodgett technique. The use of different solvents, mixtures of solvents and surfactants has been investigated in order to improve the stability of MOF dispersions and reduce particle aggregation. The compact MOF/surfactant films containing 10 wt % octadecylphoshonic acid (ODP) have been deposited on substrates of different nature by Langmuir–Blodgett (LB) and Langmuir–Schaefer (LS) methods, showing that the presence of even only one MOF/ODP monolayer can increase the water contact angle of highly hydrophilic substrates such as mica or glass up to 120°. These films were characterized by scanning electron microscopy, grazing incidence X-ray diffraction, Fourier transform infrared spectroscopy and atomic force microscopy, revealing the formation of a continuous film where ODP molecules adopt an almost vertical position and cover MOF particles. Moreover, the presence of MOF particles significantly enhances the surface roughness and allows ultrathin, hydrophobic coverage to be obtained. Finally, it has been shown that the crystallinity and the porosity of the MOF remains almost unaltered in MOF/ODP films., The research leading to these results has received funding from the European Union Seventh Framework Programme (FP7/2007-2013) under grant agreement number 608490, project M4CO2, and also financial support from Spanish MINECO and FEDER (projects MAT2016-78257-R and MAT2017-86826-R), the Aragon Government (DGA) and the ESF (research groups E31_17R). Miguel A. Andrés wants to acknowledge the support of Ministerio de Educación from the Spanish Government under a FPU grant (Formación de Profesorado Universitario)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

PBI mixed matrix hollow fiber membrane: Influence of ZIF-8 filler over H2/CO2 separation performance at high temperature and pressure

  • Etxeberria-Benavides, Miren
  • Johnson, Timothy
  • Cao, Shuai
  • Zornoza, Beatriz
  • Coronas, Joaquín
  • Sánchez-Laínez, Javier
  • Sabetghadam, Anahid
  • Liu, Xinlei
  • Andres-Garcia, Eduardo
  • Kapteijn, Freek
  • Gascón, Jorge
  • David, Oana
High performance and commercially attractive mixed-matrix membranes were developed for H2/CO2 separation via a scalable hollow fiber spinning process. Thin (~300 nm) and defect-free selective layers were successfully created with a uniform distribution of the nanosized (~60 nm) zeolitic-imidazole framework (ZIF-8) filler within the polymer (polybenzimidazole, PBI) matrix. These membranes were able to operate at high temperature (150 °C) and pressure (up to 30 bar) process conditions required in treatment of pre-combustion and syngas process gas streams. Compared with neat PBI hollow fibers, filler incorporation into the polymer matrix leads to a strong increase in H2 permeance from 65 GPU to 107 GPU at 150 °C and 7 bar, while the ideal H2/CO2 selectivity remained constant at 18. For mixed gas permeation, there is competition between H2 and CO2 transport inside ZIF-8 structure. Adsorption of CO2 in the nanocavities of the filler suppresses the transport of the faster permeating H2 and consequently decreases the H2 permeance with total feed pressure down to values equal to the pure PBI hollow fibers for the end pressure of 30 bar. Therefore, the improvement of fiber performance for gas separation with filler addition is compromised at high operating feed pressures, which emphasizes the importance of membrane evaluation under relevant process conditions., The authors acknowledge the financial support of the European Research Council under the European Union’s Seventh Framework Programme (FP/2007-2013), under grant agreement no. 608490, M4CO2 project., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Solvent-exchange process in MOF ultrathin films and its effect on CO2 and methanol adsorption

  • Andrés, Miguel A.
  • Fontaine, Philippe
  • Goldmann, Michel
  • Serre, Christian
  • Roubeau, Olivier
  • Gascón, Ignacio
Metal-organic framework (MOF) activation is crucial for the use of MOFs in several applications and solvent-exchange process is a necessary step in many activation methods. In this contribution, we have explored in situ MOF monolayer film formation at the air-water interface. Nanoparticles (NPs) of the Al trimesate MIL-96(Al) retain chloroform into their micropores, which considerably diminishes the CO2 adsorption capacity of MOF films. However, a solvent-exchange process between chloroform and water increases CO2 film adsorption capacity by 30%. Total Reflection X-Ray Fluorescence (TRXF) allows studying the kinetics of this process at the air-water interface, that strongly depends on the NP size. The conclusions derived from in situ studies allow optimizing the ex situ activation procedure of MIL-96(Al) films deposited onto quartz crystal microbalance (QCM) substrates in order to maximize CO2 and methanol adsorption., We acknowledge the financial support from the European Union Seventh Framework Programme (FP7/2007-2013) under grant agreement number 608490, project M4CO2; and also financial support from Spanish MINECO and FEDER (projects MAT2016-78257-R and MAT2017-86826-R), from the Aragon Government (DGA) and FEDER (research group E31_17R) and from the University of Zaragoza (JIUZ-2015-CIE-02). M.A. Andrés acknowledges the support of Ministerio de Educación from the Spanish Government under a FPU grant (Formación de Profesorado Universitario, FPU14/05367)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

A robust eco-compatible microporous iron coordination polymer for CO2 capture

  • Benzaqui, Marvin
  • Wahiduzzaman, Mohammad
  • Zhao, Heng
  • Hasan, Md. Rafiul
  • Steenhaut, Timothy
  • Saad, Aly
  • Marrot, Jérôme
  • Normand, Périne
  • Grenèche, Jean Marc
  • Heymans, Nicolas
  • De Weireld, Guy
  • Tissot, Antoine
  • Shepard, William
  • Filinchuk, Yaroslav
  • Hermans, Sophie
  • Carn, Florent
  • Malankowska, Magdalena
  • Téllez, Carlos
  • Coronas, Joaquín
  • Maurin-Pasturel, Guillaume
  • Steunou, Nathalie
  • Serre, Christian
Iron(III) carboxylate based metal organic frameworks (MOFs)/porous coordination polymers (PCPs) have sparked great interest owing to their high structural diversity and tunable porosity, excellent stability, tailored functionality and their scalability as well as green synthesis associated with their biocompatible and biodegradable character. Herein, we present a new robust Fe(III) based PCP (labelled MIL-178(Fe)) built up from chains of corner sharing Fe octahedra interconnected by 1,2,4-benzene tricarboxylic acid, delimiting one dimensional narrow pore channels (pore diameter < 4.5 Å) decorated with polar groups (μ2-OH and –CO2H functions). These structural and chemical features are suitable for the selective adsorption of CO2. MIL-178(Fe) was synthesized following a simple and green protocol in water under near ambient conditions using non-toxic reactants, allowing the production of sub-micrometer sized MIL-178(Fe) particles in a large amount (30 g). As shown by single-gas isotherms and CO2/N2 co-adsorption experiments as well as molecular simulations, this material exhibits a moderate CO2 capacity at low pressure but a high CO2/N2 selectivity. This is fully consistent with the presence of μ2-OH groups acting as CO2 adsorption sites, as revealed from both molecular simulations and in situ PXRD experiments. Finally, the good compatibility of this MOF with the elastomer block copolymer Pebax®-3533 allowed the processing of homogeneous and defect-free mixed matrix membranes with a MIL-178(Fe) loading of up to 25 wt% that outperformed pure Pebax®-3533 membranes for CO2/N2 separation., We acknowledge the European Community Seventh Framework Program (FP7/2007-2013) for funding the research presented in this article under Grant Agreement No. 608490 (Project M4CO2). The computational work was performed using HPC resources from GENCI-CINES (Grant A0100907613)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Asymmetric polybenzimidazole membranes with thin selective skin layer containing ZIF-8 for H 2 /CO 2 separation at pre-combustion capture conditions

  • Sánchez-Laínez, Javier
  • Zornoza, Beatriz
  • Téllez, Carlos
  • Coronas, Joaquín
This work addresses an optimization in the fabrication of flat PBI membranes containing ZIF-8 nanoparticles for gas separation purposes. The PBI membranes were prepared in an asymmetric configuration on P84® supports, representing a new way of preparing flat PBI membranes. An optimization of the conditions for the PBI phase inversion preparation method, including the dope composition (in the 15–26 wt% range), has been carried out to obtain PBI membranes with a 1 µm selective skin layer. The asymmetric membranes showed an unprecedented gas separation capacity in pre-combustion CO2 capture, much superior to that of dense membranes, under harsh operating conditions (250 °C and 6 bar feed), performing up to 20.3 GPU of H2 and a H2/CO2 selectivity of 35.6. Their much thinner selective layer made possible the increase in selectivity because of the saturation of the CO2 flow at high pressures. The reduction in the amount of ZIF-8 for obtaining a membrane with the same filler loading (3.7 vs. 9.3 g/m2) was also possible; the performance of this ZIF-8 containig membrane was 22.4 GPU of H2 and a H2/CO2 selectivity of 22.3. The activation energy of the membranes, as well as the flow resistances, were calculated, providing a resistance in series model to understand the flow inside the membrane., The research leading to these results has received funding from the European Union Seventh Framework Programme (FP7/2007–2013) under grant agreement n° 608490, project M4CO2. In addition, financial support from the Spanish MINECO and FEDER (MAT2016-77290-R), the Aragón Government (T05) and the ESF is gratefully acknowledged. J. S-L. thanks the Spanish Education Ministry Program FPU2014 for his Ph.D. grant. All the microscopy work was done in the Laboratorio de Microscopías Avanzadas at the Instituto de Nanociencia de Aragón (LMA-INA). Finally, the authors would like to acknowledge the use of the Servicio General de Apoyo a la Investigación-SAI, Universidad de Zaragoza., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Beyond the H2/CO2 upper bound: One-step crystallization and separation of nano-sized ZIF-11 by centrifugation and its application in mixed matrix membranes

  • Sánchez-Laínez, Javier
  • Zornoza, Beatriz
  • Mayoral, Álvaro
  • Berenguer-Murcia, Ángel
  • Cazorla-Amorós, Diego
  • Téllez, Carlos
  • Coronas, Joaquín
The synthesis of nano-sized ZIF-11 with an average size of 36 ± 6 nm is reported. This material has been named nano-zeolitic imidazolate framework-11 (nZIF-11). It has the same chemical composition and thermal stability and analogous H2 and CO2 adsorption properties to the conventional microcrystalline ZIF-11 (i.e. 1.9 ± 0.9 μm). nZIF-11 has been obtained following the centrifugation route, typically used for solid separation, as a fast new technique (pioneering for MOFs) for obtaining nanomaterials where the temperature, time and rotation speed can easily be controlled. Compared to the traditional synthesis consisting of stirring + separation, the reaction time was lowered from several hours to a few minutes when using this centrifugation synthesis technique. Employing the same reaction time (2, 5 or 10 min), micro-sized ZIF-11 was obtained using the traditional synthesis while nano-scale ZIF-11 was achieved only by using centrifugation synthesis. The small particle size obtained for nZIF-11 allowed the use of the wet MOF sample as a colloidal suspension stable in chloroform. This helped to prepare mixed matrix membranes (MMMs) by direct addition of the membrane polymer (polyimide Matrimid®) to the colloidal suspension, avoiding particle agglomeration resulting from drying. The MMMs were tested for H2/CO2 separation, improving the pure polymer membrane performance, with permeation values of 95.9 Barrer of H2 and a H2/CO2 separation selectivity of 4.4 at 35 °C. When measured at 200 °C, these values increased to 535 Barrer and 9.1., Financial support from the Spanish MINECO (MAT2013-40566-R, CTQ2012-31762, and RyC-2009-03913), the Aragón Government and the ESF is gratefully acknowledged. In addition, research leading to these results has received funding from the European Union Seventh Framework Programme (FP7/2007–2013) under grant agreement no. 608490, project M4CO2. Finally, the use of the Servicio General de Apoyo a la Investigación-SAI (Universidad de Zaragoza) is acknowledged., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Fabrication of ultrathin MIL-96(Al) films and study of CO2 adsorption/desorption processes using quartz crystal microbalance

  • Andrés, Miguel A.
  • Benzaqui, Marvin
  • Serre, Christian
  • Steunou, Nathalie
  • Gascón, Ignacio
This contribution reports the fabrication and characterization of ultrathin films of nanoparticles of the water stable microporous Al tricarboxylate metal organic framework MIL-96(Al). The preparation of MOF dispersions in chloroform has been optimized to obtain dense monolayer films of good quality, without nanoparticle agglomeration, at the air-water interface that can be deposited onto solid substrates of different nature without any previous substrate functionalization. The MOF studied shows great interest for CO2 capture because it presents Al3+ Lewis centers and hydroxyl groups that strongly interact with CO2 molecules. A comparative CO2 adsorption study on drop-cast, Langmuir-Blodgett (LB) and Langmuir-Schaefer (LS) films using a Quartz Crystal Microbalance-based setup (QCM) has revealed that the CO2 uptake depends strongly on the film fabrication procedure and the storage conditions. Noteworthy the CO2 adsorption capacity of LB films is increased by 30% using a simple and green treatment (immersion of the film into water during 12 h just after film preparation). Finally, the stability of LB MOF monolayers upon several CO2 adsorption/desorption cycles has been demonstrated, showing that CO2 can be easily desorbed from the films at 303 K by flowing an inert gas (He). These results show that MOF LB monolayers can be of great interest for the development of MOF-based devices that require the use of very small MOF quantities, especially gas sensors., The research leading to these results has received funding from the European Union Seventh Framework Programme (FP7/2007-2013) under grant agreement number 608490, project M4CO2; and also financial support from Spanish MINECO and FEDER (project MAT2016-78257-R), from the Universidad de Zaragoza (Project JIUZ-2015-CIE-02), the Aragon Government (DGA) and the ESF (research group E54). Miguel A. Andrés wants to acknowledge the support of Ministerio de Educación from the Spanish Government under a FPU grant (Formación de Profesorado Universitario). The authors acknowledge the use of the Servicio General de Apoyo a la Investigación-SAI (Universidad de Zaragoza) and the Laboratorio de Microscopías Avanzadas (LMA) at the Instituto de Nanociencia de Aragón (INA, Universidad de Zaragoza), LMA-INA, for offering access to their instruments and expertise., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Hydrogen separation at high temperature with dense and asymmetric membranes based on PIM-EA(H2)-TB/PBI blends

  • Sánchez-Laínez, Javier
  • Zornoza, Beatriz
  • Carta, Mariolino
  • Malpass-Evans, Richard
  • McKeown, Neil B.
  • Téllez, Carlos
  • Coronas, Joaquín
The preparation of dense and asymmetric flat membranes from the blending of polybenzimidazole (PBI) and (1.5–20 wt %) of a polymer of intrinsic microporosity (PIM-EA(H2)-TB) is reported. Thermal characterization validated the blend by revealing a single glass transition temperature, which suggests the absence of polymer phase segregation. In addition, the decomposition activation energy and d-spacing of the blends follow trends that correlate with the amount of PIM component. The membranes have been tested for the separation of H2/CO2 mixtures. The properties of the dense membranes, which also incorporate zeolitic imidazolate-8 (ZIF-8) nanoparticles, helped understanding of the behavior of the PIM/PBI blends by which phase inversion results in high separation performance asymmetric membranes. Asymmetric membranes show H2/CO2 selectivities of 23.8 (10/90 wt % PIM/PBI) and 19.4 (20/80 wt % PIM/PBI) together with respective H2 permeances of 57.9 and 83.5 GPU at 250 °C and 6 bar feed pressure. The gas separation performance of these asymmetric blends has been fitted to an empirical model, showing the influence of the amount of PIM and the feed pressure., The research comprising this work has received financial support from the European Union Seventh Framework Programme (FP7/2007-2013) under Grant Agreement No. 608490, project M4CO2. In addition, the authors acknowledge the funding received from the Spanish MINECO and FEDER (MAT2016-77290-R), the Aragón Government (T43-17R), and the European Social Fund. J.S-L. in particular thanks the Spanish Education Ministry Program FPU2014., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Influence of ZIF-8 particle size in the performance of polybenzimidazole mixed matrix membranes for pre-combustion CO2 capture and its validation through interlaboratory test

  • Sánchez-Laínez, Javier
  • Zornoza, Beatriz
  • Cao, Shuai
  • Sabetghadam, Anahid
  • Seoane, Beatriz
  • Gascón, Jorge
  • Kapteijn, Freek
  • Téllez, Carlos
  • Coronas, Joaquín
J. Sánchez-Laínez et al., The preparation and performance of mixed matrix membranes (MMMs) based on polybenzimidazole (PBI) and ZIF-8 nanoparticles of different average sizes (50, 70 and 150 nm) as filler are reported. MMMs containing 10 and 20 wt% of ZIF-8 were tested for H2/CO2 separation (pre-combustion CO2 capture) at 150 °C and feed pressures from 3 to 6 bar. The addition of ZIF-8 resulted in a clear improvement in membrane performance. Embedding 20 wt% of ZIF-8 resulted in a H2 permeability increase of six times and the H2/CO2 selectivity increased nearly by 55% compared to the bare PBI polymer membrane. Both permeability and selectivity improved as the filler size increased, due to the lower degree of agglomeration of the largest particles, that may be less active owing to their smaller external surface area. MMMs synthesized using dry 150 nm ZIF-8 filler showed a better performance than those containing wet filler. Apart from agglomeration concerns favoring wet filler handling as evidenced by infrared characterization, the MMM preparation with wet filler is simpler than with dry filler. Finally, the reproducibility of the membranes was confirmed by a European interlaboratory Round Robin test involving three different institutions., Financial support from the Spanish MINECO (MAT2013-40556-R), the Aragón Government (T05) and the ESF is gratefully acknowledged. The research leading to these results has received funding from the European Union Seventh Framework Programme (FP7/2007–2013) under Grant Agreement no. 608490, project M4CO2. All the microscopy work was done in the Laboratorio de Microscopías Avanzadas at the Instituto de Nanociencia de Aragón (LMA-INA). The use of the Servicio General de Apoyo a la Investigación-SAI (Universidad de Zaragoza) is acknowledged. J.G. and B.S. gratefully acknowledge financial support from the European Research Council under the European Union's Seventh Framework Programme (FP/2007–2013) /ERC Grant Agreement no. 335746, CrystEng-MOF-MMM., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Langmuir-blodgett films of the metal-organic framework MIL-101(Cr): Preparation, characterization, and CO2 adsorption study Using a QCM-based setup

  • Benito, Javier
  • Sorribas, Sara
  • Lucas, Irene
  • Coronas, Joaquín
  • Gascón, Ignacio
This work reports the fabrication and characterization of Langmuir–Blodgett films of nanoparticles (size 51 ± 10 nm) of the metal organic framework MIL-101(Cr). LB film characterization by SEM, UV–vis, GIXRD, and QCM has shown that the addition of 1 wt % of behenic acid to MOF dispersion allows obtaining dense monolayers at the air–water interface that can be deposited onto solid substrates of different nature with transfer ratios close to 1. Moreover, a QCM-based setup has been built and used for the first time to measure CO2 adsorption isotherms at 303 K on MOF LB films, proving that LB films with MOF masses between 1.2 (1 layer) and 2.3 (2 layers) μg can be used to obtain accurate adsorption values at 100 kPa, similar to those obtained by conventional adsorption methods that require much larger MOF quantities (tens of milligrams)., The research leading to these results has received funding from the European Union Seventh Framework Programme (FP7/2007-2013) under grant agreement no 608490, project M4CO2, and also financial support from the Universidad de Zaragoza (Project JIUZ-2015-CIE-02), the Aragon Government (DGA) and the ESF (research groups E54 and T05)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Metal-organic framework based mixed matrix membranes: A solution for highly efficient CO2 capture?

  • Seoane, Beatriz
  • Coronas, Joaquín
  • Gascón, Ignacio
  • Etxeberria-Benavides, Miren
  • Karvan, Oğuz
  • Caro, Jürgen
  • Kapteijn, Freek
  • Gascón, Jorge
The field of metal-organic framework based mixed matrix membranes (M(4)s) is critically reviewed, with special emphasis on their application in CO2 capture during energy generation. After introducing the most relevant parameters affecting membrane performance, we define targets in terms of selectivity and productivity based on existing literature on process design for pre- and post-combustion CO2 capture. Subsequently, the state of the art in M(4)s is reviewed against these targets. Because final application of these membranes will only be possible if thin separation layers can be produced, the latest advances in the manufacture of M(4) hollow fibers are discussed. Finally, the recent efforts in understanding the separation performance of these complex composite materials and future research directions are outlined., The research leading to these results has received funding from the European Union Seventh Framework Programme (FP7/2007–2013) under grant agreement no. 608490, project M4CO2 and (FP/2007–2013)/ERC Grant Agreement no. 335746, CrystEng-MOF-MMM (J. Gascon)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

On the chemical filler-polymer interaction of nano- and micro-sized ZIF-11 in PBI mixed matrix membranes and their application for H2/CO2 separation

  • Sánchez-Laínez, Javier
  • Zornoza, Beatriz
  • Téllez, Carlos
  • Coronas, Joaquín
The evolution of nano- and micro-sized ZIF-11 (nZIF-11 and ZIF-11, respectively) when embedded into a PBI polymeric matrix is studied. The prepared membranes, with loadings up to 55 wt%, have been characterized through several techniques (XRD, SEM, FTIR, TGA, 13C NMR and XPS) and the changes in the morphology of the fillers upon combination with PBI, as well as in the chemical environment of their main atoms (interactions between the linker of the filler and the benzyl rings of the polymeric bIm units) are discussed. All the membranes have been tested at temperatures ranging between 70 and 200 °C to study their H2/CO2 separation performance. The integration of both types of MOF in the polymeric phase improves not only the hydrogen permeability but also the selectivity in comparison with the pure polymer in all cases. H2 permeability increases due to a better diffusion of the penetrants, while CO2 adsorption on the MOF and solution in the polymer decreases. The best result obtained corresponds to the membrane with 55 wt% loading of ZIF-11, with 495 Barrer of H2 permeability and a H2/CO2 selectivity of 7.0., The research leading to these results has received funding from the European Union Seventh Framework Programme (FP7/2007–2013) under grant agreement no. 608490, project M4CO2. In addition, financial support from the Spanish MINECO (MAT2013-40556-R), the Aragón Government and the ESF is gratefully acknowledged., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Polymer-stabilized percolation membranes based on nanosized zeolitic imidazolate frameworks for H2/CO2 separation

  • Sánchez-Laínez, Javier
  • Friebe, Sebastian
  • Zornoza, Beatriz
  • Mundstock, Alexander
  • Strauß, Ina
  • Téllez, Carlos
  • Caro, Jürgen
  • Coronas, Joaquín
This work shows the preparation of self-supported composite membranes prepared with the nano-sized zeolitic imidazolate frameworks (ZIFs): ZIF-8, ZIF-7(III) and ZIF-7/8 core-shells. The membranes consist of compressed pellets of ZIF nanoparticles (up to 74 wt% loading) stabilized with gas-impermeable epoxy resin, providing a gas transport-selective percolation network named polymer-stabilized percolation membrane (PSPM). The different PSPMs have been characterized by SEM, TGA, XRD, FTIR and Raman. FIB/SEM has provided a 3D reconstruction of the composite thanks to the slice and view technique, allowing a perfect visualization of the inside of the network. The N2 adsorption properties have also been studied and compared with those of ZIFs in powder state. The gas separation performance of these membranes has been tested for the H2/CO2 mixture. The PSPMs were tested with feed pressures up to 5 bar, obtaining H2 permeabilities of hundreds of Barrer and a maximum H2/CO2 selectivity of 12.3., The research leading to these results has received funding from the European Union Seventh Framework Programme (FP7/2007-2013) under grant agreement n° 608490, project M4CO2. Financial support from the Spanish MINECO and FEDER (MAT2016-77290-R), the Aragón Government (T05) and the ESF is gratefully acknowledged. J. S-L. thanks Spanish Education Ministry Program FPU2014 his PhD grant. Part of the microscopy work was done in the Laboratorio de Microscopías Avanzadas at the Instituto de Nanociencia de Aragón (LMA-INA)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Synthesis of ZIF-93/11 hybrid nanoparticles via post-synthetic modification of ZIF-93 and their use for H2/CO2 separation

  • Sánchez-Laínez, Javier
  • Zornoza, Beatriz
  • Dawson, Daniel M.
  • Wright, Paul A.
  • Téllez, Carlos
  • Coronas, Joaquín
Joaquín Coronas et al., The present work shows the synthesis of nano-sized hybrid zeolitic imidazolate frameworks (ZIFs) with the rho topology based on a mixture of the linkers benzimidazole (bIm) and 4-methyl-5-imidazolecarboxaldehyde (4-m-5-ica). The hybrid ZIF was obtained by post-synthetic modification of ZIF-93 in a bIm solution. The use of different solvents, MeOH and N,N-dimethylacetamide (DMAc), and reaction times led to differences in the quantity of bIm incorporated to the framework, from 7.4 to 23 % according to solution-state NMR spectroscopy. XPS analysis showed that the mixture of linkers was also present at the surface of the particles. The inclusion of bIm to the ZIF-93 nanoparticles improved the thermal stability of the framework and also increased the hydrophobicity according to water adsorption results. N2 and CO2 adsorption experiments revealed that the hybrid material has an intermediate adsorption capacity, between those of ZIF-93 and ZIF-11. Finally, ZIF-93/11 hybrid materials were applied as fillers in polybenzimidazole (PBI) mixed matrix membranes (MMMs). These MMMs were used for H2 /CO2 separation (at 180 °C) reaching values of 207 Barrer of H2 and a H2 /CO2 selectivity of 7.7 that clearly surpassed the Robeson upper bound (corrected for this temperature)., The research leading to these results has received funding from the European Union Seventh Framework Programme (FP7/2007–2013) under grant agreement no. 608490, project M4CO2. In addition, financial support from the Spanish MINECO and FEDER (MAT2016-77290-R), the Aragón Government (T05) and the ESF is gratefully acknowledged. J.S.L. thanks the Spanish Education Ministry Program FPU2014 for his PhD grant. All the microscopy work was done in the Laboratorio de Microscopías Avanzadas at the Instituto de Nanociencia de Aragón (LMA-INA). The authors would like to acknowledge the use of the Servicio General de Apoyo a la Investigación-SAI, Universidad de Zaragoza., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Tuning the separation properties of zeolitic imidazolate framework core-shell structures: Via post-synthetic modification

  • Sánchez-Laínez, Javier
  • Veiga, Adrián
  • Zornoza, Beatriz
  • Balestra, Salvador R. G.
  • Hamad, Said
  • Ruiz-Salvador, A. Rabdel
  • Calero, Sofía
  • Téllez, Carlos
  • Coronas, Joaquín
The conversion of ZIF-8 into ZIF-7 via post-synthetic modification with benzimidazole has been monitored by quantifying the liberated 2-methylimidazole by chromatography. The reaction kinetics have been adjusted to the shrinking core model, providing the diffusion coefficient of bIm inside the pores and the reaction kinetic constant (2.86 × 10−7 cm2 s−1 and 1.36 × 10−4 cm s−1, respectively). A wide variety of ZIF-7/8 hybrid core–shell frameworks have been obtained during this reaction. The most promising have been characterized by SEM/TEM, TGA, N2 and CO2 adsorption, FTIR and 13C NMR, showing features of the coexistence of both phases inside the frameworks. Their structures have also been simulated, providing comparable XRD and adsorption results. The hybrid material has been used as a filler for PBI mixed matrix membranes (MMMs) applied to H2/CO2 separation, enhancing the performances of the bare PBI polymer and MMMs containing ZIF-8 or ZIF-7 as a filler, with a maximum H2 permeability value of 1921 Barrer and a H2/CO2 selectivity of 11.8., The research leading to these results has received funding from the European Union Seventh Framework Programme (FP7/2007–2013) under grant agreement no 608490, project M4CO2. In addition, financial support from the Spanish MINECO and FEDER (MAT2016-77290-R and CTP2016-80206-P), the Aragón Government (T05) and the ESF is gratefully acknowledged. J. S.-L. thanks the Spanish Education Ministry Program FPU2014 for his PhD grant. S. R. G. Balestra also thanks the Spanish MINECO for his predoctoral fellowship (BES-2014-067825 from CTQ2013-48396-P). All the microscopy work was done at the Laboratorio de Microscopías Avanzadas at the Instituto de Nanociencia de Aragón (LMA-INA). Finally, the authors would like to acknowledge the use of the Servicio General de Apoyo a la Investigación-SAI, Universidad de Zaragoza., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Ultrapermeable thin film ZIF-8/polyamide membrane for H2/CO2 separation at high temperature without using sweep gas

  • Sánchez-Laínez, Javier
  • Paseta, Lorena
  • Navarro, Marta
  • Zornoza, Beatriz
  • Téllez, Carlos
  • Coronas, Joaquín
The use of thin film composites containing metal–organic frameworks (MOFs) as filler is of widespread interest for nanofiltration issues, since their thin selective layer allows a high permeation flow. The application of this kind of membranes for gas separation should provide a better permeance in comparison with other polymeric membranes and a reduction in the amount of MOF required for their fabrication. Here, the preparation of 50–100 nm thick polyamide flat membranes containing zeolitic imidazolate framework-8 (ZIF-8) nanoparticles is shown via interfacial polymerization, containing a lower amount of MOF (0.013 g m−2 membrane) as compared to other membranes used for gas separation. The membranes are applied for H2/CO2 separation at high temperatures and pressures, showing a stable performance at 180 °C for at least seven days. Outstanding separation values are 328 GPU of H2 and a H2/CO2 selectivity of 18.1 at 180 °C and 6 bar feed without transmembrane pressure. These membranes, also measurable without sweep gas, are highly suitable for industrial application., The research leading to these results has received funding from the European Union Seventh Framework Programme (FP7/2007-2013) under grant agreement no. 608490, project M4CO2. In addition, financial support from the Spanish MINECO and FEDER (MAT2016-77290-R), the Aragón Government (T05) and the ESF is gratefully acknowledged. J. S.-L. thanks the Spanish Education Ministry Program FPU2014 and L.P. the Ministry of Economy, Industry and Competitiveness Program FPI2014 for their PhD grants., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Effect of bridgehead methyl substituents on the gas permeability of Tröger’s-base derived polymers of intrinsic microporosity

  • Malpass-Evans, Richard
  • Rose, Ian
  • Fuoco, Alessio
  • Bernardo, Paola
  • Clarizia, Gabriele
  • McKeown, Neil B.
  • Jansen, Johannes C.
  • Carta, Mariolino
A detailed comparison of the gas permeability of four Polymers of Intrinsic Microporosity containing Tröger's base (TB-PIMs) is reported. In particular, we present the results of a systematic study of the differences between four related polymers, highlighting the importance of the role of methyl groups positioned at the bridgehead of ethanoanthracene (EA) and triptycene (Trip) components. The PIMs show BET surface areas between 845-1028 m2 g-1 and complete solubility in chloroform, which allowed for the casting of robust films that provided excellent permselectivities for O2/N2, CO2/N2, CO2/CH4 and H2/CH4 gas pairs so that some data surpass the 2008 Robeson upper bounds. Their interesting gas transport properties were mostly ascribed to a combination of high permeability and very strong size-selectivity of the polymers. Time lag measurements and determination of the gas diffusion coefficient of all polymers revealed that physical ageing strongly increased the size-selectivity, making them suitable for the preparation of thin film composite membranes., The work leading to these results has received funding from the European Union’s Seventh Framework Program (FP7/2007-2013) under grant agreement n° 608490, project M4CO2., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Synthesis and gas permeation properties of tetraoxidethianthrene-based polymers of intrinsic microporosity

  • Felemban, Sarah A.
  • Bezzu, C. Grazia
  • Comesaña-Gándara, Bibiana
  • Jansen, Johannes C.
  • Fuoco, Alessio
  • Esposito, Elisa
  • Carta, Mariolino
  • McKeown, Neil B.
A series of nine polymers of intrinsic microporosity (PIMs) derived from different bis-catechol monomers and 2,3,7,8-tetrafluoro-5,5′,10,10′-tetraoxidethianthrene (TOT) were synthesised and tested for their potential use as gas separation membranes. As powders, they demonstrate significant nitrogen adsorption at 77 K allowing apparent BET surface areas ranging from 432–785 m2 g−1 to be calculated. Six of the polymers were found to be soluble in quinoline facilitating the casting of self-standing films to allow the assessment of their gas separation properties. Spirobifluorene-based polymers exhibited the highest gas permeability, approaching the performance of the archetypal PIM-1, and the data for some are placed close to the 2008 Robeson upper bounds for O2/N2 and CO2/CH4. Ageing studies showed a gradual decrease in permeability, accompanied by an increase in selectivity that moved the data more-or-less parallel to the Robeson upper bounds. The two polymers with the lowest and highest gas permeability were both tested over the temperature range 25–55 °C and an enhancement in permeability for all gases, with the exception of CO2, was observed along with decreased selectivity for almost all gas pairs. The latter seems to be due to the simultaneous drop in both diffusivity selectivity and solubility selectivity for all gas pairs, but especially those involving CO2, due to a strong decrease in solubility with increasing temperature. The analysis of the energetic and entropic selectivity provides further insight into the remarkable transport properties of PIMs. Overall, the tetraoxidethianthrene unit proves to be a suitable building block for use in PIM synthesis for applications in gas separation membranes and these PIMs have a one to two orders of magnitude higher permeability than more common polysulfones., The research leading to these results has received funding from the EU FP7 Framework Program under grant agreement no. 608490, project M4CO2., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Single and mixed gas permeability studies on mixed matrix membranes composed of MIL-101 (Cr) or MIL-177 (Ti) and highly permeable polymers of intrinsic microporosity

  • Esposito, Elisa
  • Carta, Mariolino
  • Fuoco, Alessio
  • Monteleone, Marcello
  • Comesaña-Gándara, Bibiana
  • Jansen, Johannes C.
et al., The gas transport properties of mixed matrix membranes (MMMs), prepared by dispersing nanoparticles of MOFs MIL-101(Cr) or MIL-177(Ti) into highly permeable Polymers of Intrinsic Microporosity PIM-EA-TB or PIM-TMN-Trip, were investigated. The homogeneity of the dispersion was confirmed by means of Scanning Electron Microscopy (SEM) and Energy-dispersive X-ray (EDX) mapping analysis. Single gas time-lag measurements provided the permeability and ideal selectivity of different gas pairs, both after treatment of the MMMs with methanol and after natural aging over an extended period (up to 2000 days). This data demonstrated that the gas size-sieving pores of MIL-101(Cr) and MIL-177(Ti) and their good dispersion into the PIM matrix results in MMMs with enhanced gas separation performance, as compared to films composed solely of the polymer. The comparison of actual permeability with the Maxwell model for PIM-EA-TB with both MOFs confirmed the good dispersion and the absence of anomalies, whereas the inconsistency of permeability with prediction data for PIM-TMN-Trip suggests that the MOFs improved the polymer properties, stiffening or occupying the polymer free volume. In particular, the incorporation of MIL-101(Cr) into PIM-EA-TB significantly enhances the H2 permeability from ∼6000 to 13,000 Barrer, with a concurrent increase of the H2/N2 selectivity from 14 to 21. MIL-177(Ti) also enhances the H2/N2 selectivity to 20 due to a slight reduction of the N2 permeability. The addition of MIL-101(Cr) and MIL-177(Ti) into the ultra-permeable PIM-TMN-Trip showed more modest increases in H2 permeability and H2/N2 selectivity from 4.6 to ∼ 10. Hence the data for some of the MMMs surpass the 2008, and even approach the 2015/2019 Robeson’s upper bounds, particularly for gas pairs including H2., The work leading to these results has received funding from the European Community’s Seventh Framework Program under grant agreement no. 608490, project M4CO2., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Polymer ultrapermeability from the inefficient packing of 2D chains

  • Rose, Ian
  • Bezzu, C. Grazia
  • Carta, Mariolino
  • Comesaña-Gándara, Bibiana
  • Jansen, Johannes C.
  • McKeown, Neil B.
The promise of ultrapermeable polymers, such as poly(trimethylsilylpropyne) (PTMSP), for reducing the size and increasing the efficiency of membranes for gas separations remains unfulfilled due to their poor selectivity. We report an ultrapermeable polymer of intrinsic microporosity (PIM-TMN-Trip) that is substantially more selective than PTMSP. From molecular simulations and experimental measurement we find that the inefficient packing of the two-dimensional (2D) chains of PIM-TMN-Trip generates a high concentration of both small (<0.7 nm) and large (0.7–1.0 nm) micropores, the former enhancing selectivity and the latter permeability. Gas permeability data for PIM-TMN-Trip surpass the 2008 Robeson upper bounds for O2/N2, H2/N2, CO2/N2, H2/CH4 and CO2/CH4, with the potential for biogas purification and carbon capture demonstrated for relevant gas mixtures. Comparisons between PIM-TMN-Trip and structurally similar polymers with three-dimensional (3D) contorted chains confirm that its additional intrinsic microporosity is generated from the awkward packing of its 2D polymer chains in a 3D amorphous solid. This strategy of shape-directed packing of chains of microporous polymers may be applied to other rigid polymers for gas separations., The research leading to these results has received funding from the Horizon 2020/FP7 Framework Program under grant agreement no. 608490, project M4CO2 and from the EPSRC (UK) grant numbers EP/M01486X/1 and EP/K008102/2. This work was also supported by the US National Science Foundation (DMR-1604376) and the Leverhulme Trust, UK (RPG-2014-308). High-performance computational resources were provided by the University of Florida Research Computing and the Research Computing and Cyberinfrastructure unit at Pennsylvania State University., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Hydrophobic assembly of molecular catalysts at the gas–liquid–solid interface drives highly selective CO2 electromethanation

  • McKee, Morgan
  • Carta, Mariolino
  • Kühnel, Moritz F.
  • Kornienko, Nikolay
McKee, M., et al., Molecular catalysts offer tunable active and peripheral sites, rendering them ideal model systems to explore fundamental concepts in catalysis. However, hydrophobic designs are often regarded as detrimental for dissolution in aqueous electrolytes. Here we show that established cobalt terpyridine catalysts modified with hydrophobic perfluorinated alkyl side chains can assemble at the gas–liquid–solid interfaces on a gas diffusion electrode. We find that the self-assembly of these perfluorinated units on the electrode surface results in a catalytic system selective for electrochemical CO2 reduction to CH4, whereas every other cobalt terpyridine catalyst reported previously was only selective for CO or formate. Mechanistic investigations suggest that the pyridine units function as proton shuttles that deliver protons to the dynamic hydrophobic pocket in which CO2 reduction takes place. Finally, integration with fluorinated carbon nanotubes as a hydrophobic conductive scaffold leads to a Faradaic efficiency for CH4 production above 80% at rates above 10 mA cm−2—impressive activities for a molecular electrocatalytic system., N.K. and M.M. acknowledge support from NSERC Discovery Grant RGPIN-2019-05927. This work was also supported by the EPSRC (EP/S017925/1 to M.F.K.), the Welsh Government (Quebec-Wales Joint Call For Projects to M.F.K.), HEFCW (RWIF Collaboration Booster to M.F.K.), Erasmus+ (to M.K.) and Swansea University (start-up funds to M.F.K.). We thank J. D. McGettrick for assistance with XPS data collection and processing. K. Klementiev is acknowledged for assistance with XAFS data collection. H.S. acknowledges MAX IV Laboratory for beamtime on Balder Beamline under proposal 20240083. Research conducted at MAX IV, a Swedish national user facility, is supported by the Swedish Research Council under contract no. 2018-07152, the Swedish Governmental Agency for Innovation Systems under contract no. 2018-04969, and Formas under contract no. 2019-02496. H.S. also acknowledges the EU/Interreg Aurora/Sustainable Hydrogen project for financial support, as well as support from the ANRF, Department of Science and Technology, India, through the Ramanujan Faculty Award (RJF/2023/000058), the Strategic Research Council within the Research Council of Finland decision 358422 and JustH2Transit, and thanks M. Huttula., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Redefining the Robeson upper bounds for CO2/CH4 and CO2/N2 separations using a series of ultrapermeable benzotriptycene-based polymers of intrinsic microporosity

  • Comesaña-Gándara, Bibiana
  • Chen, Jie
  • Bezzu, C. Grazia
  • Carta, Mariolino
  • Rose, Ian
  • Ferrari, Maria-Chiara
  • Esposito, Elisa
  • Fuoco, Alessio
  • Jansen, Johannes C.
  • McKeown, Neil B.
Membranes composed of Polymers of Intrinsic Microporosity (PIMs) have the potential for energy efficient industrial gas separations. Here we report the synthesis and gas permeability data of a series of ultrapermeable PIMs, of two-dimensional chain conformation and based on benzotriptycene structural units, that demonstrate remarkable ideal selectivity for most gas pairs of importance. In particular, the CO2 ultrapermeability and high selectivity for CO2 over CH4, of key importance for the upgrading of natural gas and biogas, and for CO2 over N2, of importance for cost-effective carbon capture from power plants, exceed the performance of the current state-of-the-art polymers. All of the gas permeability data from this series of benzotriptycene-based PIMs are placed well above the current 2008 Robeson upper bounds for CO2/CH4 and CO2/N2. Indeed, the data for some of these polymers fall into a linear correlation on the benchmark Robeson plots [i.e. log(PCO2/PCH4) versus log PCO2 and log(PCO2/PN2) versus log PCO2], which are parallel to, but significantly above, that of the 2008 CO2/CH4 and CO2/N2 upper bounds, allowing their revision. The redefinition of these upper bounds sets new aspirational targets for polymer chemists to aim for and will result in more attractive parametric estimates of energy and cost efficiencies for carbon capture and natural/bio gas upgrading using state-of-the-art CO2 separation membranes., The research leading to these results has received funding from the EU FP7 Framework Program under grant agreement no. 608490, project M4CO2 and from the EPSRC (UK) grant numbers EP/M01486X/1, EP/R000468/1 and EP/K008102/2., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

A highly rigid and gas selective methanopentacene-based polymer of intrinsic microporosity derived from Troger's base polymerization

  • Williams, Rhodri
  • Burt, Luke. A.
  • Esposito, Elisa
  • Jansen, Johannes C.
  • Tocci, Elena
  • Rizzuto, Carmen
  • Lanč, Marek
  • Carta, Mariolino
  • McKeown, Neil. B.
Polymers of intrinsic microporosity (PIMs) have been identified as potential next generation membrane materials for the separation of gas mixtures of industrial and environmental relevance. Based on the exceptionally rigid methanopentacene (MP) structural unit, a Polymer of Intrinsic Microporosity (PIM-MP-TB) was designed to demonstrate high selectivity for gas separations. PIM-MP-TB was prepared using a polymerisation reaction involving the formation of Tröger's base linking groups and demonstrated an apparent BET surface area of 743 m2 g−1 as a powder. The microporosity of PIM-MP-TB was also characterized by chain packing simulations. PIM-MP-TB proved soluble in chlorinated solvents and was cast as a robust, free-standing film suitable for gas permeation measurements. Despite lower gas permeability as compared to previously reported PIMs, high selectivities for industrially relevant gas pairs were obtained, surpassing the 2008 Robeson upper bound for H2/CH4 and O2/N2, (e.g., PO2 = 999 Barrer; αO2/N2 = 5.0) and demonstrating a clear link between polymer rigidity and selectivity. Upon aging, the permeability data move parallel to the Robeson upper bounds with a decrease of permeability, compensated by a related increase in selectivity. Mixed gas permeation measurement for CO2/CH4 and CO2/N2 mixtures confirmed the excellent selectivity of PIM-MP-TB for potentially relevant separations such as biogas upgrading and CO2 capture from flue gas. Importantly, unlike other high performing PIMs, PIM-MP-TB is prepared in four simple steps from a cheap starting material., The work leading to these results has received funding from the European Union's Seventh Framework Program (FP7/2007–2013) under grant agreement no. 608490, project M4CO2., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

The synthesis, chain-packing simulation and long-term gas permeability of highly selective spirobifluorene-based polymers of intrinsic microporosity

  • Bezzu, C. Grazia
  • Carta, Mariolino
  • Ferrari, Maria-Chiara
  • Jansen, Johannes C.
  • Monteleone, Marcello
  • Esposito, Elisa
  • Fuoco, Alessio
  • Hart, Kyle
  • Liyana-Arachchi, T. P.
  • Colina, Coray M.
  • McKeown, Neil. B.
Membranes composed of Polymers of Intrinsic Microporosity (SBF-PIMs) have potential for commercial gas separation. Here we report a combined simulation and experimental study to investigate the effect on polymer microporosity and gas permeability by placing simple substituents such as methyl, t-butyl and fused benzo groups onto PIMs derived from spirobifluorene (PIM-SBFs). It is shown that methyl or t-butyl substituents both cause a large increase in gas permeabilities with four methyl groups enhancing the concentration of ultramicropores (<0.7 nm), which contribute to selective gas transport. The t-butyl substituents lower selectivity by generating a greater concentration of larger, less selective, micropores (>1.0 nm). Long-term ageing studies (>3.5 years) demonstrate the potential of PIM-SBFs as high-performance membrane materials for gas separations. In particular, the data for the PIM derived from tetramethyl substituted SBF reaches the proposed 2015 Robeson upper bound for O2/N2 and, hence, hold promise for the oxygen or nitrogen enrichment of air. Mixed gas permeation measurements for CO2/CH4 of the aged PIM-SBFs also demonstrate their potential for natural gas or biogas upgrading., The research leading to these results has received funding from the EU FP7 Framework Program under grant agreement no. 608490, project M4CO2 and from the EPSRC (UK) grant numbers EP/M01486X/1 and EP/K008102/2. This work was also supported by the US National Science Foundation (DMR-1604376)., Peer reviewed
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Langmuir-Blodgett Films of the Metal-Organic Framework MIL-101(Cr): Preparation, Characterization, and CO2 Adsorption Study Using a QCM-Based Setup

  • Benito. J
  • Sorribas. S
  • Lucas. I
  • Coronas. J
  • Gascon.I
This work reports the fabrication and characterization of Langmuir–Blodgett films of nanoparticles (size 51 ± 10 nm) of the metal organic framework MIL-101(Cr). LB film characterization by SEM, UV–vis, GIXRD, and QCM has shown that the addition of 1 wt % of behenic acid to MOF dispersion allows obtaining dense monolayers at the air–water interface that can be deposited onto solid substrates of different nature with transfer ratios close to 1. Moreover, a QCM-based setup has been built and used for the first time to measure CO2 adsorption isotherms at 303 K on MOF LB films, proving that LB films with MOF masses between 1.2 (1 layer) and 2.3 (2 layers) µg can be used to obtain accurate adsorption values at 100 kPa, similar to those obtained by conventional adsorption methods that require much larger MOF quantities (tens of milligrams).
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Contribución de congreso (ConferenceOutput)

Ultrathin composite polymeric membranes for CO2/N2 separation with minimum thickness and high co2 permeance

  • Benito, Javier
  • Sánchez-Laínez, Javier
  • Zornoza, Beatriz
  • Martín, Santiago
  • Carta, Mariolino
  • Malpass-Evans, Richard
  • Téllez, Carlos
  • McKeown, Neil B.
  • Coronas, Joaquín
  • Gascón, Ignacio
The use of ultrathin films as selective layers in composite membranes offers significant advantages in gas separation for increasing productivity while reducing the membrane size and energy costs. In this contribution, composite membranes have been obtained by the successive deposition of approximately 1 nm thick monolayers of a polymer of intrinsic microporosity (PIM) on top of dense membranes of the ultra-permeable poly[1-(trimethylsilyl)-1-propyne] (PTMSP). The ultrathin PIM films (30 nm in thickness) demonstrate CO2 permeance up to seven times higher than dense PIM membranes using only 0.04¿% of the mass of PIM without a significant decrease in CO2/N2 selectivity.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Tuning the separation properties of zeolitic imidazolate framework core-shell structures via post-synthetic modification

  • Sánchez-Laínez, J.
  • Veiga, A.
  • Zornoza, B.
  • Balestra, S.R.G.
  • Hamad, S.
  • Ruiz-Salvador, A.R.
  • Calero, S.
  • Téllez, C.
  • Coronas, J.
The conversion of ZIF-8 into ZIF-7 via post-synthetic modification with benzimidazole has been monitored by quantifying the liberated 2-methylimidazole by chromatography. The reaction kinetics have been adjusted to the shrinking core model, providing the diffusion coefficient of bIm inside the pores and the reaction kinetic constant (2.86 × 10-7 cm2 s-1 and 1.36 × 10-4 cm s-1, respectively). A wide variety of ZIF-7/8 hybrid core-shell frameworks have been obtained during this reaction. The most promising have been characterized by SEM/TEM, TGA, N2 and CO2 adsorption, FTIR and 13C NMR, showing features of the coexistence of both phases inside the frameworks. Their structures have also been simulated, providing comparable XRD and adsorption results. The hybrid material has been used as a filler for PBI mixed matrix membranes (MMMs) applied to H2/CO2 separation, enhancing the performances of the bare PBI polymer and MMMs containing ZIF-8 or ZIF-7 as a filler, with a maximum H2 permeability value of 1921 Barrer and a H2/CO2 selectivity of 11.8.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Ultrapermeable Thin Film ZIF-8/Polyamide Membrane for H-2/CO2 Separation at High Temperature without Using Sweep Gas

  • Sanchez-Lainez, J.
  • Paseta, L.
  • Navarro, M.
  • Zornoza, B.
  • Tellez, C.
  • Coronas, J.
The use of thin film composites containing metal-organic frameworks (MOFs) as filler is of widespread interest for nanofiltration issues, since their thin selective layer allows a high permeation flow. The application of this kind of membranes for gas separation should provide a better permeance in comparison with other polymeric membranes and a reduction in the amount of MOF required for their fabrication. Here, the preparation of 50-100 nm thick polyamide flat membranes containing zeolitic imidazolate framework-8 (ZIF-8) nanoparticles is shown via interfacial polymerization, containing a lower amount of MOF (0.013 g m(-2) membrane) as compared to other membranes used for gas separation. The membranes are applied for H-2/CO2 separation at high temperatures and pressures, showing a stable performance at 180 degrees C for at least seven days. Outstanding separation values are 328 GPU of H-2 and a H-2/CO2 selectivity of 18.1 at 180 degrees C and 6 bar feed without transmembrane pressure. These membranes, also measurable without sweep gas, are highly suitable for industrial application.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Fabrication of ultrathin MIL-96(Al) films and study of CO2 adsorption/desorption processes using quartz crystal microbalance

  • Andrés, M.A.
  • Benzaqui, M.
  • Serre, C.
  • Steunou, N.
  • Gascón, I.
This contribution reports the fabrication and characterization of ultrathin films of nanoparticles of the water stable microporous Al tricarboxylate metal organic framework MIL-96(Al). The preparation of MOF dispersions in chloroform has been optimized to obtain dense monolayer films of good quality, without nanoparticle agglomeration, at the air-water interface that can be deposited onto solid substrates of different nature without any previous substrate functionalization. The MOF studied shows great interest for CO2 capture because it presents Al3+ Lewis centers and hydroxyl groups that strongly interact with CO2 molecules. A comparative CO2 adsorption study on drop-cast, Langmuir-Blodgett (LB) and Langmuir-Schaefer (LS) films using a Quartz Crystal Microbalance-based setup (QCM) has revealed that the CO2 uptake depends strongly on the film fabrication procedure and the storage conditions. Noteworthy the CO2 adsorption capacity of LB films is increased by 30% using a simple and green treatment (immersion of the film into water during 12 h just after film preparation). Finally, the stability of LB MOF monolayers upon several CO2 adsorption/desorption cycles has been demonstrated, showing that CO2 can be easily desorbed from the films at 303 K by flowing an inert gas (He). These results show that MOF LB monolayers can be of great interest for the development of MOF-based devices that require the use of very small MOF quantities, especially gas sensors.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Ultrathin hydrophobic films based on the metal organic framework UiO-66-COOH(Zr)

  • Andres, Miguel A.
  • Sicard, Clemence
  • Serre, Christian
  • Roubeau, Olivier
  • Gascon, Ignacio
This work reports on the fabrication, optimization and characterization of ultrathin films containing submicrometer particles (sMPs) of the hydrophilic and water stable UiO-66-COOH(Zr) metal organic framework (MOF). MOF particles of approximate to 200 nm have been synthesized and assembled at the air-water interface by the Langmuir-Blodgett technique. The use of different solvents, mixtures of solvents and surfactants has been investigated in order to improve the stability of MOF dispersions and reduce particle aggregation. The compact MOF/surfactant films containing 10 wt % octadecylphoshonic acid (ODP) have been deposited on substrates of different nature by Langmuir-Blodgett (LB) and Langmuir-Schaefer (LS) methods, showing that the presence of even only one MOF/ODP monolayer can increase the water contact angle of highly hydrophilic substrates such as mica or glass up to 120 degrees. These films were characterized by scanning electron microscopy, grazing incidence X-ray diffraction, Fourier transform infrared spectroscopy and atomic force microscopy, revealing the formation of a continuous film where ODP molecules adopt an almost vertical position and cover MOF particles. Moreover, the presence of MOF particles significantly enhances the surface roughness and allows ultrathin, hydrophobic coverage to be obtained. Finally, it has been shown that the crystallinity and the porosity of the MOF remains almost unaltered in MOF/ODP films.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Synthesis of ZIF-93/11 Hybrid Nanoparticles via Post-Synthetic Modification of ZIF-93 and Their Use for H2/CO2 Separation

  • Sánchez-Laínez, J.
  • Zornoza, B.
  • Orsi, A.F.
  • Lozinska, M.M.
  • Dawson, D.M.
  • Ashbrook, S.E.
  • Francis, S.M.
  • Wright, P.A.
  • Benoit, V.
  • Llewellyn, P.L.
  • Téllez, C.
  • Coronas, J.
The present work shows the synthesis of nano-sized hybrid zeolitic imidazolate frameworks (ZIFs) with the rho topology based on a mixture of the linkers benzimidazole (bIm) and 4-methyl-5-imidazolecarboxaldehyde (4-m-5-ica). The hybrid ZIF was obtained by post-synthetic modification of ZIF-93 in a bIm solution. The use of different solvents, MeOH and N, N-dimethylacetamide (DMAc), and reaction times led to differences in the quantity of bIm incorporated to the framework, from 7.4 to 23 % according to solution-state NMR spectroscopy. XPS analysis showed that the mixture of linkers was also present at the surface of the particles. The inclusion of bIm to the ZIF-93 nanoparticles improved the thermal stability of the framework and also increased the hydrophobicity according to water adsorption results. N2 and CO2 adsorption experiments revealed that the hybrid material has an intermediate adsorption capacity, between those of ZIF-93 and ZIF-11. Finally, ZIF-93/11 hybrid materials were applied as fillers in polybenzimidazole (PBI) mixed matrix membranes (MMMs). These MMMs were used for H2/CO2 separation (at 180 °C) reaching values of 207 Barrer of H2 and a H2/CO2 selectivity of 7.7 that clearly surpassed the Robeson upper bound (corrected for this temperature).
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

The fabrication of ultrathin films and their gas separation performance from polymers of intrinsic microporosity with two-dimensional (2D) and three-dimensional (3D) chain conformations

  • Benito, J.
  • Vidal, J.
  • Sánchez-Laínez, J.
  • Zornoza, B.
  • Téllez, C.
  • Martín, S.
  • Msayib, K.J.
  • Comesaña-Gándara, B.
  • McKeown, N.B.
  • Coronas, J.
  • Gascón, I.
The expansion of the use of polymeric membranes in gas separation requires the development of membranes based on new polymers with improved properties and their assessment under real operating conditions. In particular, the fabrication of ultrathin films of high performance polymers that can be used as the selective layer in composite membranes will allow large reductions in the amount of the expensive polymer used and, hence, the cost of membrane fabrication. In this contribution, two polymers of intrinsic microporosity (PIMs) with very different chain configurations (two-dimensional, 2D, chains or conventional contorted three-dimensional, 3D, conformation) have been compared in their ability to form ultrathin films, showing the relevance of polymer design to obtain compact and defect-free films. Monolayers of the 2D polymer PIM-TMN-Trip can be efficiently deposited onto poly[1-(trimethylsilyl)-1-propyne] (PTMSP) to obtain composite membranes with a CO2/N2 selectivity similar to that of the corresponding thick membranes of the same PIM using only a small fraction of the selective polymer (less than 0.1%).
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Hydrogen Separation at High Temperature with Dense and Asymmetric Membranes Based on PIM-EA(H2)-TB/PBI Blends

  • Sánchez-Laínez, J.
  • Zornoza, B.
  • Carta, M.
  • Malpass-Evans, R.
  • McKeown, N.B.
  • Téllez, C.
  • Coronas, J.
The preparation of dense and asymmetric flat membranes from the blending of polybenzimidazole (PBI) and (1.5-20 wt %) of a polymer of intrinsic microporosity (PIM-EA(H2)-TB) is reported. Thermal characterization validated the blend by revealing a single glass transition temperature, which suggests the absence of polymer phase segregation. In addition, the decomposition activation energy and d-spacing of the blends follow trends that correlate with the amount of PIM component. The membranes have been tested for the separation of H2/CO2 mixtures. The properties of the dense membranes, which also incorporate zeolitic imidazolate-8 (ZIF-8) nanoparticles, helped understanding of the behavior of the PIM/PBI blends by which phase inversion results in high separation performance asymmetric membranes. Asymmetric membranes show H2/CO2 selectivities of 23.8 (10/90 wt % PIM/PBI) and 19.4 (20/80 wt % PIM/PBI) together with respective H2 permeances of 57.9 and 83.5 GPU at 250 °C and 6 bar feed pressure. The gas separation performance of these asymmetric blends has been fitted to an empirical model, showing the influence of the amount of PIM and the feed pressure.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Solvent-exchange process in MOF ultrathin films and its effect on CO2 and methanol adsorption

  • Andrés, M.A.
  • Fontaine, P.
  • Goldmann, M.
  • Serre, C.
  • Roubeau, O.
  • Gascón, I.
Metal-organic framework (MOF) activation is crucial for the use of MOFs in several applications and solvent-exchange process is a necessary step in many activation methods. In this contribution, we have explored in situ MOF monolayer film formation at the air-water interface. Nanoparticles (NPs) of the Al trimesate MIL-96(Al) retain chloroform into their micropores, which considerably diminishes the CO2 adsorption capacity of MOF films. However, a solvent-exchange process between chloroform and water increases CO2 film adsorption capacity by 30%. Total Reflection X-Ray Fluorescence (TRXF) allows studying the kinetics of this process at the air-water interface, that strongly depends on the NP size. The conclusions derived from in situ studies allow optimizing the ex situ activation procedure of MIL-96(Al) films deposited onto quartz crystal microbalance (QCM) substrates in order to maximize CO2 and methanol adsorption.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

A robust eco-compatible microporous iron coordination polymer for CO2 capture

  • Benzaqui, Marvin
  • Wahiduzzaman, Mohammad
  • Zhao, Heng
  • Hasan, Md Rafiul
  • Steenhaut, Timothy
  • Saad, Ali
  • Marrot, Jérôme
  • Normand, Périne
  • Greneche, Jean-Marc
  • Heymans, Nicolas
  • De Weireld, Guy
  • Tissot, Antoine
  • Shepard, William
  • Filinchuk, Yaroslav
  • Hermans, Sophie
  • Carn, Florent
  • Manlankowska, Magdalena
  • Téllez, Carlos
  • Coronas, Joaquín
  • Maurin, Guillaume
  • Steunou, Nathalie
  • Serre, Christian
Iron(iii) carboxylate based metal organic frameworks (MOFs)/porous coordination polymers (PCPs) have sparked great interest owing to their high structural diversity and tunable porosity, excellent stability, tailored functionality and their scalability as well as green synthesis associated with their biocompatible and biodegradable character. Herein, we present a new robust Fe(iii) based PCP (labelled MIL-178(Fe)) built up from chains of corner sharing Fe octahedra interconnected by 1, 2, 4-benzene tricarboxylic acid, delimiting one dimensional narrow pore channels (pore diameter < 4.5 angstrom) decorated with polar groups (mu(2)-OH and -CO2H functions). These structural and chemical features are suitable for the selective adsorption of CO2. MIL-178(Fe) was synthesized following a simple and green protocol in water under near ambient conditions using non-toxic reactants, allowing the production of sub-micrometer sized MIL-178(Fe) particles in a large amount (30 g). As shown by single-gas isotherms and CO2/N-2 co-adsorption experiments as well as molecular simulations, this material exhibits a moderate CO2 capacity at low pressure but a high CO2/N-2 selectivity. This is fully consistent with the presence of mu(2)-OH groups acting as CO2 adsorption sites, as revealed from both molecular simulations and in situ PXRD experiments. Finally, the good compatibility of this MOF with the elastomer block copolymer Pebax (R)-3533 allowed the processing of homogeneous and defect-free mixed matrix membranes with a MIL-178(Fe) loading of up to 25 wt% that outperformed pure Pebax (R)-3533 membranes for CO2/N-2 separation.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Asymmetric polybenzimidazole membranes with thin selective skin layer containing ZIF-8 for H2/CO2 separation at pre-combustion capture conditions

  • Sánchez-Laínez, J.
  • Zornoza, B.
  • Téllez, C.
  • Coronas, J.
This work addresses an optimization in the fabrication of flat PBI membranes containing ZIF-8 nanoparticles for gas separation purposes. The PBI membranes were prepared in an asymmetric configuration on P84® supports, representing a new way of preparing flat PBI membranes. An optimization of the conditions for the PBI phase inversion preparation method, including the dope composition (in the 15–26 wt% range), has been carried out to obtain PBI membranes with a 1 µm selective skin layer. The asymmetric membranes showed an unprecedented gas separation capacity in pre-combustion CO2 capture, much superior to that of dense membranes, under harsh operating conditions (250 °C and 6 bar feed), performing up to 20.3 GPU of H2 and a H2/CO2 selectivity of 35.6. Their much thinner selective layer made possible the increase in selectivity because of the saturation of the CO2 flow at high pressures. The reduction in the amount of ZIF-8 for obtaining a membrane with the same filler loading (3.7 vs. 9.3 g/m2) was also possible; the performance of this ZIF-8 containig membrane was 22.4 GPU of H2 and a H2/CO2 selectivity of 22.3. The activation energy of the membranes, as well as the flow resistances, were calculated, providing a resistance in series model to understand the flow inside the membrane.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

PBI mixed matrix hollow fiber membrane: Influence of ZIF-8 filler over H2/CO2 separation performance at high temperature and pressure

  • Etxeberria-Benavides, M.
  • Johnson, T.
  • Cao, S.
  • Zornoza, B.
  • Coronas, J.
  • Sanchez-Lainez, J.
  • Sabetghadam, A.
  • Liu, X.
  • Andres-Garcia, E.
  • Kapteijn, F.
  • Gascon, J.
  • David, O.
High performance and commercially attractive mixed-matrix membranes were developed for H2/CO2 separation via a scalable hollow fiber spinning process. Thin (~300 nm) and defect-free selective layers were successfully created with a uniform distribution of the nanosized (~60 nm) zeolitic-imidazole framework (ZIF-8) filler within the polymer (polybenzimidazole, PBI) matrix. These membranes were able to operate at high temperature (150 °C) and pressure (up to 30 bar) process conditions required in treatment of pre-combustion and syngas process gas streams. Compared with neat PBI hollow fibers, filler incorporation into the polymer matrix leads to a strong increase in H2 permeance from 65 GPU to 107 GPU at 150 °C and 7 bar, while the ideal H2/CO2 selectivity remained constant at 18. For mixed gas permeation, there is competition between H2 and CO2 transport inside ZIF-8 structure. Adsorption of CO2 in the nanocavities of the filler suppresses the transport of the faster permeating H2 and consequently decreases the H2 permeance with total feed pressure down to values equal to the pure PBI hollow fibers for the end pressure of 30 bar. Therefore, the improvement of fiber performance for gas separation with filler addition is compromised at high operating feed pressures, which emphasizes the importance of membrane evaluation under relevant process conditions.