Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 12
Encontrada(s) 1 página(s)

Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Experimental and predicted vapour-liquid equilibrium of the binary mixtures n-heptane + chlorobutane isomers

  • Antón, V.
  • Martín, S.
  • Lafuente, C.
  • Gascón, I.
The study of the isothermal vapour-liquid equilibrium (VLE) of the binary mixtures n-heptane plus chlorobutane isomers (1-chlorobutane, 2-chlorobutane, 1-chloro-2-methylpropane or 2-chloro-2-methylpropane) at three different temperatures, T = 288.15, 298.15 and 308.15 K, is presented in this contribution. The experimental results were correlated using Wilson equation and the thermodynamic consistency of the data was checked by the van Ness method. Furthermore, two different methods have been used to predict the phase equilibrium in isothermal conditions: a pure group contribution method (modified-UNIFAC) and a group contribution equation of state (VTPR).
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Langmuir-Blodgett Films of the Metal-Organic Framework MIL-101(Cr): Preparation, Characterization, and CO2 Adsorption Study Using a QCM-Based Setup

  • Benito. J
  • Sorribas. S
  • Lucas. I
  • Coronas. J
  • Gascon.I
This work reports the fabrication and characterization of Langmuir–Blodgett films of nanoparticles (size 51 ± 10 nm) of the metal organic framework MIL-101(Cr). LB film characterization by SEM, UV–vis, GIXRD, and QCM has shown that the addition of 1 wt % of behenic acid to MOF dispersion allows obtaining dense monolayers at the air–water interface that can be deposited onto solid substrates of different nature with transfer ratios close to 1. Moreover, a QCM-based setup has been built and used for the first time to measure CO2 adsorption isotherms at 303 K on MOF LB films, proving that LB films with MOF masses between 1.2 (1 layer) and 2.3 (2 layers) µg can be used to obtain accurate adsorption values at 100 kPa, similar to those obtained by conventional adsorption methods that require much larger MOF quantities (tens of milligrams).
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Low variability of single-molecule conductance assisted by bulky metal–molecule contacts

  • Ferradas, Ruben R.
  • Marques-Gonzalez, Santiago
  • Osorio, Henrry M.
  • Ferrer, Jaime
  • Cea, Pilar
  • Milan, David C.
  • Vezzoli, Andrea
  • Higgins, Simon J.
  • Nichols, Richard J.
  • Low, Paul J.
  • Garcia-Suarez, Victor M.
  • Martin, Santiago
A detailed study of the trimethylsilylethynyl moiety, –C[triple bond, length as m-dash]CSiMe3 (TMSE), as an anchoring group in metal|molecule|metal junctions, using a combination of experiment and density functional theory is presented. It is shown that the TMSE anchoring group provides improved control over the molecule–substrate arrangement within metal|molecule|metal junctions, with the steric bulk of the methyl groups limiting the number of highly transmissive binding sites at the electrode surface, resulting in a single sharp peak in the conductance histograms recorded by both the in situ break junction and I(s) STM techniques. As a consequence of the low accessibility of the TMSE group to surface binding configurations of measurable conductance, only about 10% of gold break junction formation cycles result in the clear formation of molecular junctions in the experimental histograms. The DFT-computed transmission characteristics of junctions formed from the TMSE-contacted oligo(phenylene)ethynylene (OPE)-based molecules described here are dominated by tunneling effects through the highest-occupied molecular orbitals (HOMOs). This gives rise to similar conductance characteristics in these TMSE-contacted systems as found in low conductance-type junctions based on comparably structured OPE-derivatives with amine-contacts that also conduct through HOMO-based channels.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Towards a metallic top contact electrode in molecular electronic devices exhibiting a large surface coverage by photoreduction of silver cations

  • Martin, Santiago
  • Ballesteros, Luz M.
  • Gonzalez-Orive, A.
  • Oliva, H.
  • Marques-Gonzalez, Santiago
  • Lorenzoni, Matteo
  • Nichols, Richard J.
  • Perez-Murano, Francesc
  • Low, Paul J.
  • Cea, Pilar
In this contribution the photoreduction of silver ions coordinated onto a Langmuir–Blodgett monolayer is presented as an effective method for the deposition of the top contact electrode in metal/monolayer/metal devices. Silver cations were incorporated from an aqueous AgNO3 sub-phase of Langmuir films of 4,4'-(1,4-phenylenebis(ethyne-2,1-diyl))dibenzoic acid upon the transference of these films onto a metallic substrate. Subsequent irradiation of the silver-ion functionalized Langmuir–Blodgett films with 254 nm light results in the photoreduction of silver cations to produce metallic silver nanoparticles, which are distributed over the organic monolayer and exhibit a surface coverage as large as 76% of the monolayer surface. Electrical properties of these metal/monolayer/metal devices were determined by recording I–V curves, which show a sigmoidal behaviour indicative of well-behaved junctions free of metallic filaments and short-circuits. The integrity of the organic monolayer upon the irradiation process and formation of the silver top-contact electrode has also been demonstrated through cyclic voltammetry experiments.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

All-Carbon Electrode Molecular Electronic Devices Based on Langmuir–Blodgett Monolayers

  • Sangiao, S.
  • Martín, S.
  • González-Orive, A.
  • Magén, C.
  • Low, P.J.
  • De Teresa, J.M.
  • Cea, P.
Nascent molecular electronic devices, based on monolayer Langmuir–Blodgett films sandwiched between two carbonaceous electrodes, have been prepared. Tightly packed monolayers of 4-((4-((4-ethynylphenyl)ethynyl)phenyl)ethynyl)benzoic acid are deposited onto a highly oriented pyrolytic graphite electrode. An amorphous carbon top contact electrode is formed on top of the monolayer from a naphthalene precursor using the focused electron beam induced deposition technique. This allows the deposition of a carbon top-contact electrode with well-defined shape, thickness, and precise positioning on the film with nm resolution. These results represent a substantial step toward the realization of integrated molecular electronic devices based on monolayers and carbon electrodes.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Contribución de congreso (ConferenceOutput)

Ultrathin composite polymeric membranes for CO2/N2 separation with minimum thickness and high co2 permeance

  • Benito, Javier
  • Sánchez-Laínez, Javier
  • Zornoza, Beatriz
  • Martín, Santiago
  • Carta, Mariolino
  • Malpass-Evans, Richard
  • Téllez, Carlos
  • McKeown, Neil B.
  • Coronas, Joaquín
  • Gascón, Ignacio
The use of ultrathin films as selective layers in composite membranes offers significant advantages in gas separation for increasing productivity while reducing the membrane size and energy costs. In this contribution, composite membranes have been obtained by the successive deposition of approximately 1 nm thick monolayers of a polymer of intrinsic microporosity (PIM) on top of dense membranes of the ultra-permeable poly[1-(trimethylsilyl)-1-propyne] (PTMSP). The ultrathin PIM films (30 nm in thickness) demonstrate CO2 permeance up to seven times higher than dense PIM membranes using only 0.04¿% of the mass of PIM without a significant decrease in CO2/N2 selectivity.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Thermophysical study of the binary mixtures of N, N-dimethylacetamide with 1-propanol and 1-butanol

  • Mrad, S.
  • Hichri, M.
  • Khattech, I.
  • Lafuente, C.
Several thermophysical properties such as densities, p, speeds of sound, u, refractive indices, nD, and kinematic viscosities, v, have been measured for the binary mixtures of N, N-Dimethylacetamide with 1-propanol and 1-butanol over the entire range of composition, at the temperatures (283.15, 298.15 and 313.15) K and at atmospheric pressure p = 0.1 MPa. From these experimental data, excess molar volumes, VE, excess isentropic compressibilities, ?S E , refractive index deviations, ?nD, and viscosity deviations, ??, were calculated. Then, correlated with the Redlich-Kister equation and the corresponding parameters were drived. The results obtained, were discussed in terms of structural effects and specific molecular interactions, and the influence of the alkanol chain length was also considered.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Fabrication of ultrathin MIL-96(Al) films and study of CO2 adsorption/desorption processes using quartz crystal microbalance

  • Andrés, M.A.
  • Benzaqui, M.
  • Serre, C.
  • Steunou, N.
  • Gascón, I.
This contribution reports the fabrication and characterization of ultrathin films of nanoparticles of the water stable microporous Al tricarboxylate metal organic framework MIL-96(Al). The preparation of MOF dispersions in chloroform has been optimized to obtain dense monolayer films of good quality, without nanoparticle agglomeration, at the air-water interface that can be deposited onto solid substrates of different nature without any previous substrate functionalization. The MOF studied shows great interest for CO2 capture because it presents Al3+ Lewis centers and hydroxyl groups that strongly interact with CO2 molecules. A comparative CO2 adsorption study on drop-cast, Langmuir-Blodgett (LB) and Langmuir-Schaefer (LS) films using a Quartz Crystal Microbalance-based setup (QCM) has revealed that the CO2 uptake depends strongly on the film fabrication procedure and the storage conditions. Noteworthy the CO2 adsorption capacity of LB films is increased by 30% using a simple and green treatment (immersion of the film into water during 12 h just after film preparation). Finally, the stability of LB MOF monolayers upon several CO2 adsorption/desorption cycles has been demonstrated, showing that CO2 can be easily desorbed from the films at 303 K by flowing an inert gas (He). These results show that MOF LB monolayers can be of great interest for the development of MOF-based devices that require the use of very small MOF quantities, especially gas sensors.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Volumetric and acoustic behaviour of myo-inositol in aqueous Natural Deep Eutectic Solvent solutions

  • Bergua, F.
  • Nuez, M.
  • Muñoz-Embid, J.
  • Lafuente, C.
  • Artal, M.
A study of the interactions in aqueous systems containing a sweetener, myo-inositol, and a NAtural Deep Eutectic Solvent, reline or glyceline, is presented. Both NADESs include the same acceptor group, choline chloride, and different donor groups, urea and glycerol. For this purpose, the density and speed of sound were measured for dilute mixtures, and several related properties were calculated: the standard partial molar volume, the standard partial molar isentropic compression, the standard transfer properties, Hepler's constant, and the compressibility hydration number. The results were evaluated as a function of the temperature and composition, and they show the dominance of the ionic-hydrophilic and hydrophilic-hydrophilic interactions. Moreover, the glyceline disturbs the aqueous mixtures more than the reline.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Thermophysical study of 2-acetylthiophene: experimental and modelled results

  • Antón, V.
  • Artigas, H.
  • Muñoz-Embid, J.
  • Artal, M.
  • Lafuente, C.
Several thermophysical properties have been studied for 2-acetylthiophene: (i) vapour pressure was determined at temperatures within 336.16–445.02 K; (ii) density, speed of sound, static permittivity, refractive index, surface tension, and kinematic viscosity were measured at p = 0.1 MPa and at temperatures from 278.15 K (or 283.15 K for the refractive index) to 338.15 K; (iii) volumetric properties were also determined at temperatures in the (283.15–338.15) K range and at pressures up to 65.0 MPa. From these experimental values, different derivative properties have been calculated such as enthalpy of vaporization, isobaric expansibility, isothermal and isentropic compressibility, dipole moment, entropy and enthalpy of surface formation, and dynamic viscosity. All experimental properties were correlated and the results were explained through the intermolecular interactions. Moreover PC-SAFT EoS was used to model the thermodynamic behaviour of the compound. Finally, this EoS combined with the Density Gradient Theory allowed obtaining the influence parameter for the surface tension of 2-acetylthiophene.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Towards molecular electronic devices based on 'all-carbon' wires

  • Moneo, Andrea
  • González-Orive, Alejandro
  • Bock, Soren
  • Fenero, Marta
  • Herrer, I. Lucía
  • Milan, David C.
  • Lorenzoni, Matteo
  • Nichols, Richard J.
  • Cea, Pilar
  • Perez-Murano, Francesc
  • Low, Paul J.
  • Martin, Santiago
Nascent molecular electronic devices based on linear ‘all-carbon’ wires attached to gold electrodes through robust and reliable C–Au contacts are prepared via efficient in situ sequential cleavage of trimethylsilyl end groups from an oligoyne, Me3Si–(C[triple bond, length as m-dash]C)4–SiMe3 (1). In the first stage of the fabrication process, removal of one trimethylsilyl (TMS) group in the presence of a gold substrate, which ultimately serves as the bottom electrode, using a stoichiometric fluoride-driven process gives a highly-ordered monolayer, Au|C[triple bond, length as m-dash]CC[triple bond, length as m-dash]CC[triple bond, length as m-dash]CC[triple bond, length as m-dash]CSiMe3 (Au|C8SiMe3). In the second stage, treatment of Au|C8SiMe3 with excess fluoride results in removal of the remaining TMS protecting group to give a modified monolayer Au|C[triple bond, length as m-dash]CC[triple bond, length as m-dash]CC[triple bond, length as m-dash]CC[triple bond, length as m-dash]CH (Au|C8H). The reactive terminal C[triple bond, length as m-dash]C–H moiety in Au|C8H can be modified by ‘click’ reactions with (azidomethyl)ferrocene (N3CH2Fc) to introduce a redox probe, to give Au|C6C2N3HCH2Fc. Alternatively, incubation of the modified gold substrate supported monolayer Au|C8H in a solution of gold nanoparticles (GNPs), results in covalent attachment of GNPs on top of the film via a second alkynyl carbon–Au σ-bond, to give structures Au|C8|GNP in which the monolayer of linear, ‘all-carbon’ C8 chains is sandwiched between two macroscopic gold contacts. The covalent carbon–surface bond as well as the covalent attachment of the metal particles to the monolayer by cleavage of the alkyne C–H bond is confirmed by surface-enhanced Raman scattering (SERS). The integrity of the carbon chain in both Au|C6C2N3HCH2Fc systems and after formation of the gold top-contact electrode in Au|C8|GNP is demonstrated through electrochemical methods. The electrical properties of these nascent metal–monolayer–metal devices Au|C8|GNP featuring ‘all-carbon’ molecular wires were characterised by sigmoidal I–V curves, indicative of well-behaved junctions free of short circuits.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Viscometric study of myo-inositol in aqueous deep eutectic solvent solutions

  • Nuez, Montserrat
  • Bergua, Fernando
  • Lafuente, Carlos
  • Muñoz-Embid, Jose
  • Artal, Manuela
A viscometric study of myo-inositol in pure water and in Deep Eutectic Solvent (DES) aqueous solutions is presented. Two DES based on choline chloride as acceptor group and urea or glycerol as donor group are used. Experimental measurements of viscosities at ¿=¿99.0¿kPa and at six temperatures from 293.15 to 318.15¿K were performed. In addition, the viscometric properties such as the -coefficient, the hydration number, and the activation parameters of viscous flow were calculated. From these properties, the intermolecular interactions were evaluated. The results show that the studied sweetener is a structure-maker compound in all solvents of this work. The solute co-solute interactions are strongest in the system containing glycerol.