Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 6
Encontrada(s) 1 página(s)

Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Bridging sensing and action: autonomous object sorting by reprogrammable liquid crystal elastomers

  • Montesino, Lorena
  • López-Valdeolivas, María
  • Martínez, Jesús I.
  • Sánchez-Somolinos, Carlos
Achieving autonomy in soft robotics requires integrating sensing, planning, and actuation. Stimuli-responsive liquid crystal elastomers (LCEs) are promising for this purpose due to their intrinsic sensory capabilities, adaptability and integrability. Nevertheless, self-regulated LCE systems typically rely on single-mode bending actuators with feedback-type mechanisms, where deformation gradually increases with stimulus intensity but only causes a functional transition beyond a critical activation point. This enables autonomous switching between non-functional and functional states, however, their behavior remains reactive, limiting their ability to perform complex adaptive tasks. Here, we present a reprogrammable LCE actuator capable of autonomously sorting objects based on their green-light transmission properties. Using perylene diimide-doped LCEs and controlled green-light illumination, the actuator senses the optical properties of the object, establishing an actuation plan through spatial radical generation. Subsequent far-red irradiation triggers different actuation modes, enabling selective object sorting. This pattern-encoded actuation allows objects with different optical characteristics to trigger specific mechanical responses under identical illumination conditions. This single-material system, which is optically resettable, integrates sensory feedback, deliberative decision-making, and adaptive mechanical responses. Surpassing the reactive nature of conventional self-regulated LCE systems, our approach advances LCE-based robotics toward greater autonomy, aligning with the sense-plan-act paradigm.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Holographic Whole‐Object Photopolymerization Preserving Director Alignment in Liquid Crystalline Actuators

  • Gulati, Lovish
  • Lee, Junhee
  • Norouzikudiani, Reza
  • Li, Jianfeng
  • Sánchez Somolinos, Carlos
  • DeSimone, Antonio
  • Melde, Kai
  • Song, Alexander
  • Fischer, Peer
Liquid crystalline (LC) crosslinked polymeric structures are promising for soft robotic applications, as their actuation profile is intrinsically encoded and results from the structure's shape and the LC molecular orientation (director). However, it remains challenging to fabricate 3D objects and at the same time control the director orientation within the 3D structure. Liquid crystalline molecules are commonly aligned using modified surfaces or electric/magnetic fields. However, additive manufacturing methods may locally distort the director, when fabricating 3D objects. Here, holographic microlithography is employed to form entire connected 3D objects in a single exposure by cross‐linking the LC, while allowing the director orientation within the object to be freely controlled. This enables us to independently choose a global director orientation and then realize complex 3D geometries in a single fabrication step. This approach avoids the director distortion present in sequential 3D printing and lithography methods, and allows for complex actuation profiles that are directly linked to the 3D director orientation. The method presented herein permits the rapid fabrication of complex 3D connected LC structures while preserving the molecular order, and thereby enables the fabrication of more complex 3D soft actuators.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

4D Printable Formulations of Mixed Low and High Molecular Weight Liquid Crystalline Units: A Versatile Route to Functional Soft Actuators

  • Ceamanos, Lorena
  • López-Valdeolivas, María
  • Lyu, Pengrong
  • Liu, Danqing
  • Broer, Dirk J.
  • Sánchez-Somolinos, Carlos
Over the last few years, 4D printing of liquid crystal elastomers (LCEs) has been explored to develop actuators with significant, reversible, and anisotropic shape changes upon external stimuli such as heat or light. Most reported ink formulations rely on photo-curable liquid crystal materials derived from high molecular weight (MW) main-chain macromers. Their rheological properties allow to program molecular alignment during direct ink writing. In contrast, formulations composed mainly of monoacrylate or diacrylate low MW mesogens are unsuitable for extrusion-based 4D printing as they fail to promote mesogen alignment during printing. This shortcoming restricts the range of chemical and physical compositions accessible to 4D printing. Here, we introduce a practical route for formulating 4D printable inks that integrate low MW mesogens. By adding an acrylate-ended macromer to the low MW constituents, these mixtures become suitable for direct ink writing. This enables the preparation of multi-functional actuators with digitally controlled director morphology and tailored properties, for example, stiffness and actuation strain, as well as light-responsive behavior when photoactive molecules are used. These results highlight the versatility of the method and suggest its potential compatibility with other functional low MW units, such as those responsive to electrical or pH stimuli.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Delayed crosslinking enables ultra-high-resolution melt electrowriting of responsive liquid crystal elastomers

  • Javadzadeh, Mehrzad
  • Fernández-Melero, María
  • Barrio, Jesús del
  • Sánchez-Somolinos, Carlos
Melt electrowriting (MEW) enables the fabrication of finely structured scaffolds with sub-micrometer resolution. However, reducing the inter-fiber distance (IFD) in MEW remains challenging due to electrostatic interactions between the charged polymer jet and previously deposited fibers, often leading to fiber bridging. Recently, we demonstrated that MEW of reactive liquid crystalline inks, followed by ultraviolet (UV) photopolymerization, enables the fabrication of digitally positioned liquid crystal elastomer (LCE) structures. Building on this, we demonstrate that tuning the UV light intensity during photopolymerization significantly improves the achievable resolution range. Lower UV intensities produce smaller minimum IFDs without fiber bridging, enabling the fabrication of highly ordered structures with IFDs down to 11 µm for 5 µm-diameter fibers, a feature that, to the best of our knowledge, surpasses the smallest IFDs previously reported for MEW. We hypothesize that slower crosslinking kinetics extend the time window for charge dissipation, reducing electrostatic interactions between the jet and the previously deposited fibers. Although the mechanism remains unclear, local variations in material flow or curing-induced surface morphology may also affect electric field distribution. Beyond resolution improvements, this strategy enables defect-free fabrication of stimuli-responsive LCEs with programmable shape transformation and actuation. UV light intensity thus emerges as a critical design parameter for MEW, with implications for other photo-crosslinkable systems.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Programming of Complex Magnetic Profiles Enforced by 4D Printed Magnetic LCE Actuators

  • Espíndola-Pérez, Erick R.
  • Goyal, Rahul
  • Gulati, Lovish
  • López-Valdeolivas, María
  • Fischer, Peer
  • Sánchez-Somolinos, Carlos
Magnetic soft actuators enable untethered, contact‐free actuation yet they are fundamentally limited by the difficulty of programming complex, three‐dimensional (3D), spatially non‐uniform magnetic profiles. Here, we introduce a four‐dimensional (4D) printing‐enabled magnetic programming strategy that overcomes this challenge by magnetizing magnetically active liquid crystal elastomers (MLCEs) in thermally actuated target states. Digitally prescribed director architectures define deterministic 3D deformations at elevated temperature, which serve as intrinsic programming templates during magnetization under a spatially uniform magnetic field. Upon cooling, relaxation of the thermomechanical deformation transforms the initially uniform magnetization into a complex, spatially varying magnetic profile that encodes the target shape as a magnetically favoured configuration. This approach enables the recovery of thermally defined shapes at room temperature under low magnetic fields and allows bidirectional and multistate actuation via simple reversal of field direction. By integrating spatial magnetic programming with controlled geometric asymmetry, we demonstrate frequency‐tunable linear locomotion and chirality‐encoded clockwise or anticlockwise rotational motion in multimaterial soft robotic architectures. This strategy decouples magnetic profile complexity from magnetization hardware, providing a scalable, template‐free route to fully 3D magnetic programming for soft robotics and untethered actuators operating under low‐field conditions.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Temperature-driven elastocaloric enhancement in amorphous elastomers with liquid-crystal mesogens

  • Rojo, Kenneth Roy
  • Cosculluela, Carlos
  • Téllez, Pedro
  • Sánchez-Somolinos, Carlos
  • Evangelisti, Marco
We report variable-temperature, direct elastocaloric measurements on an amorphous elastomer with liquid-crystal mesogens exhibiting mechanotropic ordering. Using a custom tensile setup coupled with infrared thermography, we enable rapid mechanical cycling across a broad temperature range. As temperature decreases from ambient conditions, the elastocaloric response increases markedly, reaching a maximum near −3.5 °C with adiabatic temperature changes of ΔT+ = 3.9 °C and ΔT− = −4.3 °C at 60% strain. By correlating these measurements with polymer-dynamics analysis, we identify a finite temperature window in which the elastocaloric response is maximized. This optimum reflects kinetic matching between molecular relaxation dynamics and the timescale of the mechanical loading–unloading cycle.