Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 49
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Charged versus Neutral Hydrogen-Bonded Complexes: Is There a Difference in the Nature of the Hydrogen Bonds?

  • Alkorta, Ibon
  • Mata, Ignasi
  • Molins, Elies
  • Espinosa, Enrique
A theoretical study on some carboxylic acid dimers formed by positively or negatively charged molecules has been carried out by using DFT methods. The resulting dimers possess either a charge of +2 or −2. In addition, the corresponding neutral complexes have also been considered. The electron density distribution described by the atoms in molecules and the natural bond orbital methods, as well as the electric field maps of the systems, have been analyzed and compared without finding significant differences between the neutral and ionic complexes. The interaction energy along the dissociation path of the charged dimers shows both a local minimum and a local maximum, defining a stability region between them. When this energetic profile is recalculated by removing the repulsion between the charged groups, it resembles to those of the neutral molecules. Hence, the characteristics of the charged dimers are similar to those of the neutral ones: the addition of a repulsion term for the charged groups permits to retrieve the energetic profiles dependence with the distance in the charged system. The interacting quantum atom (IQA) method has been used to calculate the interaction energy terms, including the classic Coulombic term between the whole molecules and the corresponding of the carboxylic acid groups. The IQA results show repulsive electrostatic interactions when the whole molecules are considered in the ionic complexes, but attractive ones between the carboxylic groups in both neutral and ionic complexes., This work was supported by the Spanish Ministerio de Economía y Competitividad (Grants CSD2007-00041, ENE2012-36368-C02-02, ENE2015-63969, SEV2015-0496 and CTQ2015-63997-C2-2-P), the Catalan Government (Grant PRC 2014SGR-1643), and the Autonomous Community of Madrid (S2013/MIT2841, Fotocarbon)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Model predictive control for ethanol steam reformers with membrane separation

  • Serra-Prat, María
  • Ocampo-Martínez, Carlos
  • Li, Mingming
  • Llorca, Jordi
This paper focuses on the dynamic modelling and the predictive control of an ethanol steam reformer (ESR) with Pd[sbnd]Ag membrane separation stage for the generation of pure hydrogen. Hydrogen purity necessary to feed a proton exchange membrane fuel cell (PEMFC) is required. A non-linear dynamic model of the ESR is developed together with a procedure for adjusting the model parameters in order to fit a bank of experimental data of a real ESR system. Static and dynamic analysis of the non-linear ESR model is presented. From this non-linear model, a linear, reduced order and discretised model is derived and a model predictive controller (LMPC) is designed for the ESR system. Control objectives are pure hydrogen flowrate tracking and ethanol inlet minimization. Comparisons between the non-linear and linear models are carried out to determine the control constraints. Finally, simulation results for the implemented LMPC controller are presented and discussed., This paper has been partially supported by Spanish research projects. DPI2015-69286-C3-2-R, MINECO/FEDER and ENE2015-63969-R, MINECO/FEDER. Mingming Li has been supported by the China Scholarship Council (CSC). Jordi Llorca is Serra Húnter Fellow and is grateful to ICREA Academia program., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Fast and Simple Microwave Synthesis of TiO2/Au Nanoparticles for Gas-Phase Photocatalytic Hydrogen Generation

  • May Masnou, Anna
  • Soler, Lluís
  • Torras, Miquel
  • Sallés, Pol
  • Llorca, Jordi
  • Roig Serra, Anna
The fabrication of small anatase titanium dioxide (TiO2) nanoparticles (NPs) attached to larger anisotropic gold (Au) morphologies by a very fast and simple two-step microwave-assisted synthesis is presented. The TiO2/Au NPs are synthesized using polyvinylpyrrolidone (PVP) as reducing, capping and stabilizing agent through a polyol approach. To optimize the contact between the titania and the gold and facilitate electron transfer, the PVP is removed by calcination at mild temperatures. The nanocatalysts activity is then evaluated in the photocatalytic production of hydrogen from water/ethanol mixtures in gas-phase at ambient temperature. A maximum value of 5.3 mmol·g−1cat⋅h−1 (7.4 mmol·g−1TiO2⋅h−1) of hydrogen is recorded for the system with larger gold particles at an optimum calcination temperature of 450°C. Herein we demonstrate that TiO2-based photocatalysts with high Au loading and large Au particle size (≈50 nm) NPs have photocatalytic activity., This research received funding from the Spanish Ministry of Economy and Competitiveness (MINECO) in co-funding with European Social Funds through the MAT2015-64442-R and ENE2015-63969-R projects and financial support through the Severo Ochoa Programme for Centers of Excellence in R&D (SEV-2015-0496). MINECO also funded the FPU PhD Fellow of MT (FPU16/05452) and the Juan de la Cierva Postdoctoral Fellow of AM-M (FJCI-2014-21407). Generalitat of Catalunya is acknowledged for the projects 2017SGR752 and 2017SGR128. JL is Serra Hunter Fellow and is grateful to ICREA Academia program. The authors would also like to thank Judith Oró and Belén Ballesteros for the TEM and HRTEM images and Ana Esther Carrillo for the SEM images., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Energetic, topological and electric field analyses of cation-cation nucleic acid interactions in Watson-Crick disposition

  • Alkorta, Ibon
  • Mata, Ignasi
  • Molins, Elies
  • Espinosa, Enrique
A theoretical study of the effect of the diprotonation on the nucleic acid bases (A : U, A : T and G : C) in Watson‐Crick conformation has been carried out by means of DFT computational methods in vacuum. In addition, the corresponding neutral and monoprotonated binary complexes have been considered. Most of the diprotonated species studied are stable, even though the binding energy is positive due to the overall repulsive electrostatic term. Local electrostatic attractive forces in the regions of hydrogen bonds (HBs) are responsible for equilibrium geometries, as shown by the electric field lines connecting the electrophilic and nucleophilic sites involved in the HB interactions. Secondary electrostatic effects also affect the assembling of the nucleic acid complexes in either neutral or cationic form. In particular, the electric field lines flowing from electrophilic sites in one base to nucleophilic sites in the other reinforce the linking between them. Hence, when the nucleophilic site concerns the free lone pair of the heteroatom involved in the HB interaction as acceptor, the HB distance shortens. However, if the free lone pair of the HB acceptor interacts with an electrophilic site in the same molecule, the HB distance elongates, weakening the HB interaction. The topological analysis of the electron density distribution in HB regions indicates that neutral, monoprotonated and diprotonated complexes show no differences in the nature of their HB's., This work was supported by the Spanish Ministerio de Economía y Competitividad (Grants CSD2007‐00041, ENE2015‐63969‐C3‐3‐R, SEV2015‐0496 and CTQ2015‐63997‐C2‐2‐P), the Catalan Government (Grant PRC 2017SGR‐1687), the Autonomous Community of Madrid (Grant Fotocarbon and S2013/MIT‐2841) and the French ANR project ANR‐17‐CE07‐0025‐01., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Adenine as a Halogen Bond Acceptor: A Combined Experimental and DFT Study

  • Roselló, Yannick
  • Benito, Mónica
  • Molins, Elies
  • Barceló Oliver, Miquel
  • Frontera, Carlos
In this work, we report the cocrystallization of N<sup>9</sup>-ethyladenine with 1,2,4,5-tetrafluoro-3,6-diiodobenzene (TFDIB), a classical XB donor. As far as our knowledge extends, this is the first cocrystal reported to date where an adenine derivative acts as a halogen bond acceptor. In the solid state, each adenine ring forms two centrosymmetric H-bonded dimers: one using N1···HA6–N6 and the other N7···HB6–N6. Therefore, only N3 is available as a halogen bond acceptor that, indeed, establishes an N···I halogen bonding interaction with TFDIB. The H-bonded dimers and halogen bonds have been investigated via DFT (Density Functional Theory) calculations and the Bader’s Quantum Theory of Atoms In Molecules (QTAIM) method at the B3LYP/6-311+G* level of theory. The influence of H-bonding interactions on the lone pair donor ability of N3 has also been analyzed using the molecular electrostatic potential (MEP) surface calculations., This research was funded by MINECO/AEI from Spain, project numbers ENE2015-63969, CTQ2017-85821-R FEDER and SEV2015-0496, We acknowledge support by the CSIC Open Access Publication Initiative through its Unit of Information Resources for Research (URICI), Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Topochemical synthesis of cation ordered double perovskite oxynitrides

  • Ceravola, Roberta
  • Oró, Judith
  • Black, Ashley P.
  • Ritter, C.
  • Puente-Orench, Inés
  • Mata, Ignasi
  • Molins, Elies
  • Frontera, Carlos
  • Fuertes, Amparo
Topochemical nitridation in ammonia at moderate temperatures of cation ordered Sr2FeWO6 produces new antiferromagnetic double perovskite oxynitrides Sr2FeWO6-xNx with 0 < x ≤ 1. Nitrogen introduction induces the oxidation of Fe2+ to Fe3+ and decreases TN from 38 K (x = 0) to 13 K for Sr2FeWO5N which represents the first example of a double perovskite oxynitride with both high cationic order and nitrogen content. This synthetic approach can be extended to other cation combinations expanding the possibility of new materials in the large group of double perovskites., This work was supported by the Spanish Ministerio de Economia y Competitividad (MINECO), Spain (Projects MAT2014-53500-R, MAT2015-71664-R, MAT2015-67593-P and ENE2015-63969) and it has been developed under the Materials Science PhD program of the Universitat Autònoma de Barcelona. Fellowship support to AB from MINECO (FPI, project MAT2011-24757) is gratefully acknowledged. ICMAB acknowledges financial support from MINECO through the Severo Ochoa Program (SEV- 2015-0496)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Colloidal Ni–Co–Sn nanoparticles as efficient electrocatalysts for the methanol oxidation reaction

  • Li, Junshan
  • Luo, ZhiShan
  • He, Feng
  • Zuo, Yong
  • Zhang, Chaoqi
  • Liu, Junfeng
  • Yu, Xiaoting
  • Du, Ruifeng
  • Zhang, Ting
  • Infante-Carrió, Maria F.
  • Tang, Peng-Yi
  • Arbiol, Jordi
  • Llorca, Jordi
  • Cabot, Andreu
The deployment of direct methanol fuel cells requires engineering cost-effective and durable electrocatalysts for the methanol oxidation reaction (MOR). As an alternative to noble metals, Ni-based alloys have shown excellent performance and good stability toward the MOR. Herein, we present a series of Ni3−xCoxSn2 colloidal nanoparticles (NPs) with composition tuned over the entire Ni/Co range (0 ≤ x ≤ 3). We demonstrate electrodes based on these ternary NPs to provide improved catalytic performance toward the MOR in an alkaline medium when compared with binary Ni3Sn2 NPs. A preliminary composition optimization resulted in Ni2.5Co0.5Sn2 NP-based electrodes exhibiting extraordinary mass current densities, up to 1050 mA mg−1, at 0.6 V vs. Hg/HgO in 1.0 M KOH containing 1.0 M methanol. This current density was about two-fold higher than that of Ni3Sn2 electrodes (563 mA mg−1). The excellent performance obtained with the substitution of small amounts of Ni by Co was concomitant with an increase of the surface coverage of active species and an enhancement of the diffusivity of the reaction limiting species. Additionally, saturation of the catalytic activity at higher methanol concentrations was measured for Ni3−xCoxSn2 NP-based electrodes containing a small amount of Co when compared with binary Ni3Sn2 NPs. While the electrode stability was improved with respect to elemental Ni NP-based electrodes, the introduction of small amounts of Co slightly decreased the cycling performance. Additionally, Sn, a key element to improve stability with respect to elemental Ni NPs, was observed to slowly dissolve in the presence of KOH. Density functional theory calculations on metal alloy surfaces showed the incorporation of Co within the Ni3Sn2 structure to provide more effective sites for CO and CH3OH adsorption. However, the relatively lower stability could not be related to CO or CH3OH poisoning., This work was supported by the European Regional Development Funds and by the Spanish Ministerio de Economía y Competitividad through the project SEHTOP (ENE2016-77798-C4-3-R) and VALPEC (ENE2017-85087-C3). J. Li and T. Zhang thank the China Scholarship Council (CSC) for scholarship support. T. Zhang and J. Arbiol acknowledge funding from Generalitat de Catalunya 2017 SGR 327. ICN2 acknowledges support from the Severo Ochoa Programme (MINECO, Grant no. SEV-2013-0295). IREC and ICN2 are funded by the CERCA Programme/Generalitat de Catalunya. Part of the present work has been performed in the framework of the Universitat Autònoma de Barcelona Materials Science PhD program. J. Llorca is a Serra Húnter Fellow and is grateful to the ICREA Academia program and to MINECO/FEDER grant ENE2015-63969-R and GC 2017 SGR 128., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Colloidal Ni2−xCoxP nanocrystals for the hydrogen evolution reaction

  • Liu, Junfeng
  • Wang, Zhenxing
  • David, Jeremy
  • Llorca, Jordi
  • Li, Junshan
  • Yu, Xiaoting
  • Shavel, Alexey
  • Arbiol, Jordi
  • Meyns, Michaela
  • Cabot, Andreu
A cost-effective and scalable approach was developed to produce monodisperse Ni2−xCoxP nanocrystals (NCs) with composition tuned over the entire range (0 ≤ x ≤ 2). Ni2−xCoxP NCs were synthesized using low-cost, stable and low-toxicity triphenyl phosphite (TPP) as a phosphorus source, metal chlorides as metal precursors and hexadecylamine (HDA) as a ligand. The synthesis involved the nucleation of amorphous Ni–P and its posterior crystallization and simultaneous incorporation of Co. The composition, size and morphology of the Ni2−xCoxP NCs could be controlled simply by varying the ratio of Ni and Co precursors and the amounts of TPP and HDA. Ternary Ni2−xCoxP-based electrocatalysts exhibited enhanced electrocatalytic activity toward the hydrogen evolution reaction (HER) compared to binary phosphides. In particular, NiCoP electrocatalysts displayed the lowest overpotential of 97 mV at J = 10 mA cm−2 and an excellent long-term stability. DFT calculations of the Gibbs free energy for hydrogen adsorption at the surface of Ni2−xCoxP NCs showed NiCoP to have the most appropriate composition to optimize this parameter within the whole Ni2−xCoxP series. However, the hydrogen adsorption energy was demonstrated not to be the only parameter controlling the HER activity in Ni2−xCoxP., J. David and J. Arbiol acknowledge funding from Generalitat de Catalunya 2017 SGR 327 and the Spanish MINECO project VALPEC (ENE2017-85087-C3). ICN2 acknowledges support from the Severo Ochoa Programme (SEV-2013-0295) and is funded by the CERCA Programme/Generalitat de Catalunya. J. David has received funding from the European Union’s Horizon 2020 research and innovation programme under the Marie Sklodowska-Curie grant agreement No 665919. J. Llorca is a Serra Hunter Fellow and is grateful to the ICREA Academia program and grants MINECO/FEDER ENE2015-63969-R and GC 2017 SGR 128. J. Liu, J. Li and X. Yu thank the China Scholarship Council for scholarship support. M. Meyns acknowledges a Juan de la Cierva formación grant by the Spanish MINECO., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

NiSn bimetallic nanoparticles as stable electrocatalysts for methanol oxidation reaction

  • Li, Junshan
  • Luo, ZhiShan
  • Zuo, Yong
  • Liu, Junfeng
  • Zhang, Ting
  • Tang, Peng-Yi
  • Arbiol, Jordi
  • Llorca, Jordi
  • Cabot, Andreu
Nickel is an excellent alternative catalyst to high cost Pt and Pt-group metals as anode material in direct methanol fuel cells. However, nickel presents a relatively low stability under operation conditions, even in alkaline media. In this work, a synthetic route to produce bimetallic NiSn nanoparticles (NPs) with tuned composition is presented. Through co-reduction of the two metals in the presence of appropriate surfactants, 3–5 nm NiSn NPs with tuned Ni/Sn ratios were produced. Such NPs were subsequently supported on carbon black and tested for methanol electro-oxidation in alkaline media. Among the different stoichiometries tested, the most Ni-rich alloy exhibited the highest electrocatalytic activity, with mass current density of 820 mA mg−1 at 0.70 V (vs. Hg/HgO). While this activity was comparable to that of pure nickel NPs, NiSn alloys showed highly improved stabilities over periods of 10,000 s at 0.70 V. We hypothesize this experimental fact to be associated to the collaborative oxidation of the byproducts of methanol which poison the Ni surface or to the prevention of the tight adsorption of these species on the Ni surface by modifying its surface chemistry or electronic density of states., J. Li and T. Zhang thank the China Scholarship Council for scholarship support. JA and TZ acknowledge funding from Generalitat de Catalunya 2014 SGR 1638 and the Spanish MINECO coordinated projects between IREC and ICN2 VALPEC and subprojects RESOL and ANAPHASE (ENE2017-85087-C3). ICN2 acknowledges support from the Severo Ochoa Programme (MINECO, Grant no. SEV-2013-0295) and is funded by the CERCA Programme / Generalitat de Catalunya. JL is a Serra Húnter Fellow and is grateful to ICREA Academia program and to MINECO/FEDER grant ENE2015-63969-R., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

SnP nanocrystals as anode materials for Na-ion batteries

  • Liu, Junfeng
  • Wang, Shutao
  • Kravchyk, Kostiantyn
  • Ibáñez, María
  • Krumeich, Frank
  • Widmer, Roland
  • Nasiou, Déspina
  • Meyns, Michaela
  • Llorca, Jordi
  • Arbiol, Jordi
  • Kovalenko, Maksym V.
  • Cabot, Andreu
Tin monophosphide is a layered material consisting of Sn–P–P–Sn sandwiches that are stacked on top of each other to form a three dimensional crystallographic structure. Its composition and crystal structure makes it an excellent candidate anode material for sodium-ion batteries (SIBs). However, SnP is yet to be explored for such and other applications due to its challenging synthesis. In the present work, we report the synthesis of SnP nanocrystals (NCs) from the reaction of hexamethylphosphorous triamide (HMPT) and a tin phosphonate prepared from tin oxalate and a long chain phosphonic acid. SnP NCs obtained from this reaction displayed a spherical geometry and a trigonal crystallographic phase with a superstructure attributed to ordered diphosphorus pairs. Such NCs were mixed with carbon black and used as anode materials in SIBs. SIBs based on SnP NCs and sodium(I) bis(fluorosulfonyl)imide (NaFSI) electrolyte displayed a high reversible capacity of 600 mA h g−1 at a current density of 100 mA g−1 and cycling stability for over 200 cycles. Their excellent cycling performance is associated with both the small size of the crystal domains and the particular composition and phase of SnP which prevent mechanical disintegration and major phase separation during sodiation and desodiation cycles. These results demonstrate SnP to be an attractive anode material for sodium ion batteries., DN and JA acknowledge funding from Generalitat de Catalunya 2014 SGR 1638 and the Spanish MINECO projects VALPEC and ANAPHASE (ENE2017-85087-C3-3-R). The ICN2 acknowledges support from the Severo Ochoa Programme (SEV-2013-0295) and is funded by Generalitat de Catalunya. JL thanks the China Scholarship Council for scholarship support. MM acknowledges a Juan de la Cierva formación grant by the Spanish MINECO. JLl is a Serra Húnter Fellow and is grateful to ICREA Academia program and projects MINECO/FEDER ENE2015-63969-R and GC 2017 SGR 128., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Compositionally tuned NixSn alloys as anode materials for lithium-ion and sodium-ion batteries with a high pseudocapacitive contribution

  • Li, Junshan
  • Xu, Xijun
  • Luo, ZhiShan
  • Zhang, Chaoqi
  • Yu, Xiaoting
  • Zuo, Yong
  • Zhang, Ting
  • Tang, Peng-Yi
  • Arbiol, Jordi
  • Llorca, Jordi
  • Liu, Jun
  • Cabot, Andreu
Nickel tin alloy nanoparticles (NPs) with tuned composition NixSn (0.6 ≤ x ≤ 1.9) were synthesized by a solution-based procedure and used as anode materials for Li-ion batteries (LIBs) and Na-ion batteries (SIBs). Among the compositions tested, Ni0.9Sn-based electrodes exhibited the best performance in both LIBs and SIBs. As LIB anodes, Ni0.9Sn-based electrodes delivered charge-discharge capacities of 980 mAh g−1 after 340 cycles at 0.2 A g−1 rate, which surpassed their maximum theoretical capacity considering that only Sn is lithiated. A kinetic characterization of the charge-discharge process demonstrated the electrode performance to be aided by a significant pseudocapacitive contribution that compensated for the loss of energy storage capacity associated to the solid-electrolyte interphase formation. This significant pseudocapacitive contribution, which not only translated into higher capacities but also longer durability, was associated to the small size of the crystal domains and the proper electrode composition. The performance of NixSn-based electrodes toward Na-ion storage was also characterized, reaching significant capacities above 200 mAh g−1 at 0.1 A g−1 but with a relatively fast fade over 120 continuous cycles. A relatively larger pseudocapacitive contribution was obtained in NixSn-based electrodes for SIBs when compared with LIBs, consistently with the lower contribution of the Na ion diffusion associated to its larger size., This work was supported by the European Regional Development Funds and by the Spanish Ministerio de Economía y Competitividad through the project SEHTOP (ENE2016-77798-C4-3-R). J. Li thanks the China Scholarship Council for scholarship support. This project was supported by the National Natural Science Foundation of China (no. 51771076), the “1000 plan” from Chinese Government, and the Project of Public Interest Research and Capacity Building of Guangdong Province (no. 2017A010104004). T. Zhang, P. Tang and J. Arbiol acknowledge funding from Generalitat de Catalunya 2017 SGR 327 and the Spanish MINECO coordinated projects between IREC and ICN2 VALPEC and subprojects RESOL and ANAPHASE (ENE2017-85087-C3). ICN2 acknowledges support from the Severo Ochoa Programme (MINECO, Grant no. SEV-2013-0295) and is funded by the CERCA Programme / Generalitat de Catalunya. T. Zhang has received funding from the CSC-UAB PhD scholarship program. Part of the present work has been performed in the framework of Universitat Autònoma de Barcelona Materials Science PhD program. J. Llorca is a Serra Húnter Fellow and is grateful to ICREA Academia program and to MINECO/FEDER grant ENE2015-63969-R and GC 2017 SGR 128., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Co–Sn nanocrystalline solid solutions as anode materials in lithium-ion batteries with high pseudocapacitive contribution

  • Li, Junshan
  • Xu, Xijun
  • Luo, ZhiShan
  • Zhang, Chaoqi
  • Zuo, Yong
  • Zhang, Ting
  • Tang, Peng-Yi
  • Infante-Carrió, Maria F.
  • Arbiol, Jordi
  • Llorca, Jordi
  • Liu, Jun
  • Cabot, Andreu
Co–Sn solid‐solution nanoparticles with Sn crystal structure and tuned metal ratios were synthesized by a facile one pot solution‐based procedure involving the initial reduction of a Sn precursor followed by incorporation of Co within the Sn lattice. These nanoparticles were used as anode materials for Li‐ion batteries. Among the different compositions tested, Co0.7Sn and Co0.9Sn electrodes provided the highest capacities with values above 1500 mAh g−1 at a current density of 0.2 A g−1 after 220 cycles, and up to 800 mAh g−1 at 1.0 A g−1 after 400 cycles. Up to 81 % pseudocapacitance contribution was measured for these electrodes at a sweep rate of 1.0 mV s−1, thereby indicating fast kinetics and long durability. The excellent performance of Co–Sn nanoparticle alloy‐based electrodes was attributed to both the small size of the crystal domains and their suitable composition, which buffered volume changes of Sn and contributed to a suitable electrode restructuration., This work was supported by the European Regional Development Funds and by the Spanish Ministerio de Economía y Competitividad through the project SEHTOP (ENE2016‐77798‐C4‐3‐R). J. Li thanks the China Scholarship Council for scholarship support. This project was supported by the National Natural Science Foundation of China (no. 51771076), the “1000 plan” from Chinese Government, and the Project of Public Interest Research and Capacity Building of Guangdong Province (no. 2017A010104004). TZ, PYT, MFIC and JA acknowledge funding from Generalitat de Catalunya 2017 SGR 327 and the Spanish MINECO coordinated projects between IREC and ICN2 VALPEC and subprojects RESOL and ANAPHASE (ENE2017‐85087‐C3). ICN2 acknowledges support from the Severo Ochoa Programme (MINECO, Grant no. SEV‐2013‐0295) and is funded by the CERCA Programme/ Generalitat de Catalunya. JL is a Serra Húnter Fellow and is grateful to ICREA Academia program and to MINECO/FEDER grant ENE2015‐63969‐R. TZ has received funding from the CSC‐UAB PhD scholarship program., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Chromium phosphide CrP as highly active and stable electrocatalysts for oxygen electroreduction in alkaline media

  • Liu, Junfeng
  • Yu, Xiaoting
  • Du, Ruifeng
  • Zhang, Chaoqi
  • Zhang, Ting
  • Llorca, Jordi
  • Arbiol, Jordi
  • Wang, Ying
  • Meyns, Michaela
  • Cabot, Andreu
Catalysts for oxygen reduction reaction (ORR) are key components in emerging energy technologies such as fuel cells and metal-air batteries. Developing low-cost, high performance and stable electrocatalysts is critical for the extensive implementation of these technologies. Herein, we present a procedure to prepare colloidal chromium phosphide CrP nanocrystals and we test their performance as ORR electrocatalyst. CrP-based catalysts exhibited remarkable activities with a limiting current density of 4.94 mA cm−2 at 0.2 V, a half-potential of 0.65 V and an onset potential of 0.8 V at 1600 rpm, which are comparable to commercial Pt/C. Advantageously, CrP-based catalysts displayed much higher stabilities and higher tolerances to methanol in alkaline solution. Using density functional theory calculations, we demonstrate CrP to provide a very strong chemisorption of O2 that facilitates its reduction and explains the excellent ORR performance experimentally demonstrated., This work was supported by the European Regional Development Funds and the Spanish MINECO project SEHTOP (ENE2016-77798-C4- 3-R). T. Zhang and J. Arbiol acknowledge funding from Generalitat de Catalunya 2017 SGR 327 and the Spanish MINECO project ENE2017-85087-C3. ICN2 is supported by the Severo Ochoa program from Spanish MINECO (SEV-2017-0706) and is funded by the CERCA Programme / Generalitat de Catalunya. J. Llorca is a Serra Hunter Fellow and is grateful to ICREA Academia program and grants MINECO/FEDER ENE2015-63969-R and GC 2017 SGR 128. J. Liu, X. Yu, R. Du, C. Zhang and T. Zhang thank the China Scholarship Council for scholarship support. M. Meyns acknowledges a Juan de la Cierva formación grant by theSpanish MINECO. Y. Wang thanks the National Natural Science Foundation of China for financial support (Grant Nos: 21673220, 21831003, 21733004), National Key Research and Development Program of China (2016YFA0602900) and High performance Computing Center of Jilin Province and Computing Center of Jilin University for essential support., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Graphene-supported palladium phosphide PdP2 nanocrystals for ethanol electrooxidation

  • Liu, Junfeng
  • Luo, ZhiShan
  • Li, Junshan
  • Yu, Xiaoting
  • Llorca, Jordi
  • Nasiou, Déspina
  • Arbiol, Jordi
  • Meyns, Michaela
  • Cabot, Andreu
We present a procedure to produce single-phase PdP2 nanocrystals (NCs). The approach involves the reaction of palladium(II) acetylacetonate and hexamethylphosphoroustriamide to nucleate defective Pd5P2 nanoparticles that subsequently, with further phosphorous incorporation, crystallize into PdP2. The synthesized PdP2 NCs were supported on reduced graphene oxide (rGO) and applied as electrocatalysts for ethanol oxidation. The activity of PdP2 toward the ethanol oxidation reaction (EOR) was over a threefold higher than that of Pd NCs prepared under similar conditions. Even better performance was obtained from PdP2 NCs supported on rGO, which showed current densities up to 51.4 mA cm−2 and mass activities of 1.60 A mg-1Pd, that is 4.8 and 15 times higher than Pd NCs. Besides, PdP2 NCs and PdP2/rGO catalysts showed improved stability during EOR than Pd NCs and Pd/rGO., This work was supported by the European Regional Development Funds and the Spanish MINECO project SEHTOP (ENE2016-77798-C4-3-R). D. Nasiou and J. Arbiol acknowledge funding from Generalitat de Catalunya 2017 SGR 327 and the Spanish MINECO project ANAPHASE (ENE2017-85087-C3). ICN2 acknowledges support from the Severo Ochoa Programme (SEV-2013-0295) and is funded by the CERCA Programme / Generalitat de Catalunya. J. Llorca is a Serra Hunter Fellow and is grateful to ICREA Academia program and grants MINECO/FEDER ENE2015-63969-R and GC 2017 SGR 128. J. Liu, J. Li and X. Yu thank the China Scholarship Council for scholarship support. M. Meyns acknowledges a Juan de la Cierva formación grant by the Spanish MINECO., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Porous NiTiO3/TiO2 nanostructures for photocatatalytic hydrogen evolution

  • Xing, Congcong
  • Liu, Yongpeng
  • Zhang, Yu
  • Liu, Junfeng
  • Zhang, Ting
  • Tang, Peng-Yi
  • Arbiol, Jordi
  • Soler, Lluís
  • Sivula, Kevin
  • Guijarro, Néstor
  • Wang, Xiang
  • Li, Junshan
  • Du, Ruifeng
  • Zuo, Yong
  • Cabot, Andreu
  • Llorca, Jordi
We present a strategy to produce porous NiTiO3/TiO2 nanostructures with excellent photocatalytic activity toward hydrogen generation. In a first step, nickel-doped TiO2 needle bundles were synthesized by a hydrothermal procedure. Through the sintering in air of these nanostructures, porous NiTiO3/TiO2 heterostructured rods were obtained. Alternatively, the annealing in argon of the nickel-doped TiO2 needle bundles resulted in NiOx/TiO2 elongated nanostructures. Porous NiTiO3/TiO2 structures were tested for hydrogen evolution in the presence of ethanol. Such porous heterostructures exhibited superior photocatalytic activity toward hydrogen generation, with hydrogen production rates up to 11.5 mmol h−1 g−1 at room temperature. This excellent performance is related here to the optoelectronic properties and geometric parameters of the material., This work was supported by the European Regional Development Funds and by the Spanish Ministerio de Economía y Competitividad through projects ENE2016-77798-C4-3-R and ENE2015-63969-R. Y. L. and N. G. thank the Swiss National Science Foundation (SNF) for funding under the Ambizione Energy grant no. PZENP2_166871. J.L. is a Serra Hunter fellow and is grateful to ICREA Academia program and GC 2017 SGR 128. T. Z., P.·Y. T. and J. A. acknowledge funding from Generalitat de Catalunya 2017 SGR 327 and the Spanish MINECO project ENE2017-85087-C3. ICN2 acknowledges support from the Severo Ochoa Programme (MINECO, Grant no. SEV-2013-0295) and is funded by the CERCA Programme/Generalitat de Catalunya. Part of the present work has been performed in the framework of Universitat Autònoma de Barcelona Materials Science PhD program. C. C. X., Y. Z and T. Z. thank the China Scholarship Council for scholarship support., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Solution-processed ultrathin SnS2−Pt nanoplates for photoelectrochemical water oxidation

  • Zuo, Yong
  • Liu, Yongpeng
  • Li, Junshan
  • Du, Ruifeng
  • Yu, Xiaoting
  • Xing, Congcong
  • Zhang, Ting
  • Yao, Liang
  • Arbiol, Jordi
  • Llorca, Jordi
  • Sivula, Kevin
  • Guijarro, Néstor
  • Cabot, Andreu
Tin disulfide (SnS2) is attracting significant interest because of the abundance of its elements and its excellent optoelectronic properties in part related to its layered structure. In this work, we specify the preparation of ultrathin SnS2 nanoplates (NPLs) through a hot-injection solution-based process. Subsequently, Pt was grown on their surface via in situ reduction of a Pt salt. The photoelectrochemical (PEC) performance of such nanoheterostructures as photoanode toward water oxidation was tested afterwards. Optimized SnS2–Pt photoanodes provided significantly higher photocurrent densities than bare SnS2 and SnS2-based photoanodes of previously reported study. Mott–Schottky analysis and PEC impedance spectroscopy (PEIS) were used to analyze in more detail the effect of Pt on the PEC performance. From these analyses, we attribute the enhanced activity of SnS2–Pt photoanodes reported here to a combination of the very thin SnS2 NPLs and the proper electronic contact between Pt nanoparticles (NPs) and SnS2., This work was supported by the European Regional Development Funds and by the Spanish Ministerio de Economía y Competitividad through the project SEHTOP (ENE2016-77798-C4-3-R) and VALPEC (ENE2017-85087-C3). Y.Z., J.L., R.D., X.T., and T.Z. thank China Scholarship Council for scholarship support. Y.L. and N.G. thank the Swiss National Science Foundation (SNF) for funding under the Ambizione Energy grant no. PZENP2_166871. J.L. is a Serra Húnter Fellow and is grateful to ICREA Academia program and grants MINECO/FEDER ENE2015-63969-R and GC 2017 SGR 128. T.Z. and J.A. acknowledge funding from Generalitat de Catalunya 2017 SGR 327. ICN2 acknowledges support from the Severo Ochoa Programme (MINECO, grant no. SEV-2013-0295). IREC and ICN2 are funded by the CERCA Programme/Generalitat de Catalunya. Part of the present work has been performed in the framework of Universitat Autònoma de Barcelona Materials Science PhD program., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Effect of Ce and Mn co-doping on photocatalytic performance of sol-gel TiO2

  • Tbessi, Imen
  • Benito, Mónica
  • Molins, Elies
  • LIorca, Jordi
  • Touati, Azza
  • Sayadi, Sami
  • Najjar, Wahiba
Co-doped titanium dioxide was synthesized by doping with manganese (Mn) and cerium (Ce) through a sol-gel method for the degradation of diclofenac (DCF). The synthesized products were successfully characterized by X-ray diffraction (XRD), Raman spectroscopy, Transmission electron microscopy (TEM), Scanning electron microscopy (SEM), Nitrogen physisorption at 77 K, X-ray photoelectron spectroscopy (XPS), UV–Vis diffuse reflectance (UV-DRS), photoluminescence spectroscopy (PL) and total organic carbon (TOC). It was shown that co-doping increased the specific surface area, improved the visible light absorption and extended the lifetime of photogenerated charge carriers. Furthermore, the results of the photocatalytic experiments show that the photodegradation rate of diclofenac can be approached by pseudo first-order kinetics and it followed the Langmuir-Hinshelwood model very well. The co-doped catalyst with 0.6% Mn and 1% Ce molar ratios appeared to be the most photoactive catalyst with 94% of DCF removal and an apparent rate constant of 0.012 min−1., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Silver and manganese co-doped titanium oxide aerogel for effective diclofenac degradation under UV-A light irradiation

  • Tbessi, Imen
  • Benito, Mónica
  • Llorca, Jordi
  • Molins, Elies
  • Sayadi, Sami
  • Najjar, Wahiba
The photodegradation of diclofenac from aqueous medium under UV-A light condition has been essayed using co-doped with manganese and silver TiO2 photocatalysts. X-ray diffraction, Raman spectroscopy, Scanning electron microscopy, Transmission electron microscopy, High resolution transmission electron microscopy, Energy dispersive X-ray, N2 adsorption-desorption measurements at 77 K, UV–Visible diffuse reflectance, X-ray photoelectron spectroscopy and photoluminescence analyses were used to characterize the materials. A high surface specific area of 165 m2/g, low band gap energy (2.7 eV) and effective charge separation were obtained for the 0.5%Ag-0.6%Mn/TiO2 photocatalyst. The results of the photocatalytic experiments showed that co-doping improved the photocatalytic activity of TiO2. In particular, TiO2 co-doped with 0.6 mol% Mn and 0.5 mol% Ag exhibited the maximum diclofenac removal (86%) after 4 h under UV-A light irradiation. The photodegradation rates followed a first order kinetics according to the Langmuir-Hinshelwood model, being the highest apparent rate of 0.0064 min−1. The photocatalytic performance appears as related to the specific surface area, the low optical band gap energy, the creation of surface oxygen vacancies and the efficient separation of photogenerated electron-hole pairs., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Synthesis, X‐ray characterization and density functional theory studies of N6 ‐benzyl‐N6 ‐methyladenine–M(II) complexes (M = Zn, Cd): The prominent role of π–π, C–H···π and anion–π interactions

  • Pons, Roser
  • Ibáñez, Cristina
  • Buades, Ana B.
  • Franconetti, Antonio
  • García Raso, Ángel
  • Fiol, Joan J.
  • Molins, Elies
  • Frontera, Antonio
We report the synthesis and X‐ray characterization of the N6 ‐benzyl‐N6 ‐ methyladenine ligand (L) and three metal complexes, namely [Zn(HL) Cl3]·H2O (1), [Cd(HL)2Cl4] (2) and [H2L]2[Cd3(μ‐L)2(μ‐Cl)4Cl6]·3H2O (3). Complex 1 consists of the 7H‐adenine tautomer protonated at N3 and coordinated to a tetrahedral Zn(II) metal centre through N9. The octahedral Cd(II) in complex 2 is N9 ‐coordinated to two N6 ‐benzyl‐N6 ‐methyladeninium ligands (7H‐tautomer protonated at N3) that occupy apical positions and four chlorido ligands form the basal plane. Compound 3 corresponds to a trinuclear Cd(II) complex, where the central Cd atom is six‐coordinated to two bridging μ‐L and four bridging μ‐Cl ligands. The other two Cd atoms are six‐coordinated to three terminal chlorido ligands, to two bridging μ‐Cl ligands and to the bridging μ‐L through N3. Essentially, the coordination patterns, degree of protonation and tautomeric forms of the nucleobase dominate the solid‐state architectures of 1–3. Additionally, the hydrogen‐bonding interactions produced by the endocyclic N atoms and NH groups stabilize high‐dimensional‐order supramolecular assemblies. Moreover, energetically strong anion–π and lone pair (lp)–π interactions are important in constructing the final solid‐state architectures in 1–3. We have studied the non‐covalent interactions energetically using density functional theory calculations and rationalized the interactions using molecular electrostatic potential surfaces and Bader's theory of atoms in molecules. We have particularly analysed cooperative lp–π and anion–π interactions in 1 and π+–π+ interactions in 3., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

9-Ethyladenine: Mechanochemical Synthesis, Characterization and DFT Calculations of Novel Cocrystals and Salts

  • Roselló, Yannick
  • Benito, Mónica
  • Bagués, Núria
  • Martínez, Núria
  • Moradell, Alba
  • Mata, Ignasi
  • Galcerà, Judit
  • Barceló Oliver, Miquel
  • Frontera, Antonio
  • Molins, Elies
Liquid-assisted grinding and solvent crystallizations have been undertaken to prepare salts and cocrystals of the modified nucleobase 9-ethyladenine with several carboxylic acids. The new solid forms have been characterized by X-ray powder and single-crystal diffraction, attenuated total reflectance Fourier transformed infrared spectroscopy, and thermal methods. From single-crystal structures we have observed that the length of the alkyl chain in the carboxylic acid prevents a canonical self-assembly for the longest coformer. Moreover, density functional theory (DFT) calculations combined with the quantum theory of “Atoms-in-Molecules” QTAIM have been performed to analyze the different binding modes of adenine and the energetic features of the complexes. In particular, the interaction energies of several adenine dimers and trimers, and also the hydrogen bonds with carboxylic acids interacting with Watson–Crick and Hoogsten faces of adenine, have been computed and compared., This research was funded by MINECO/AEI from Spain, project numbers ENE2015-63969, CTQ2017-85821-R FEDER, and SEV2015-0496 and by the DireccióGeneral de Recerca i Innovaciódel Govern Balear (AAEE039/2017)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Synthesis, reactivity, X-ray characterization and docking studies of N7/N9-(2-pyrimidyl)-adenine derivatives

  • Martínez, Daniel
  • Pérez, Adriá
  • Cañellas, Santiago
  • Silió, Ivan
  • Lancho, Aida
  • García Raso, Ángel
  • Fiol, Joan J.
  • Terrón, Ángel
  • Barceló Oliver, Miquel
  • Ortega Castro, Joaquín
  • Molins, Elies
  • Frontera, Antonio
The reaction of adenine with 2-chloropyrimidine yields as a major product the unexpected N7-(2-pyrimidyl)-adenine (1) and as a minor one N9-(2-pyrimidyl)-adenine (2). Both compounds have been characterized by X-ray diffraction analysis. Moreover, we report the formation of a 1:1 co-crystal (3) composed by compound (1) and adenine that was formed serendipitously during the synthesis of (1). Unexpectedly, the treatment of (1) with Brönsted acids like HCl or HNO3 causes the opening of the imidazole ring of the N7-substituted adenine, yielding N5-(pyrimidin-2-yl)pyrimidine-4,5,6-triamine (4–7) which we have X-ray characterized in its neutral, (4), monoprotonated [nitrate salt (6)] and diprotonated forms [hydrochloride salt (5) and, also, a tetrachlorozincate salt (7)]. Finally, we have used compound (5) as ligand to synthesize and X-ray characterize its complexes with Ir(III) and Ag(I) (compounds (8) and (9), respectively), where the latter is a 2D coordination polymer and the former is a discrete mononuclear complex. We have studied the supramolecular assemblies formed in the solid state by using density functional theory (DFT) calculations. Finally, DNA-docking studies of several compounds have been carried out in order to analyze their ability to interact with the DNA., We thank the MINECO/AEI from Spain for financial support (project numbers CTQ2017-85821-R, ENE2015-63969-C3-3-R, BIO2016-78057-R and SEV2015-0496, FEDER funds and CTQ2017-90802-REDT). We also thank the Direcció General de Recerca i Innovació del Govern Balear (AAEE039/2017) for funding. We thank the CTI (UIB) for computational facilities and allocation of computer time. We thank the Vice-Rector for Research and International Relations of the University of the Balearic Islands for the financial support in setting up the single-crystal X-ray diffraction facility., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Alkoxide structure effect on size and size distribution of Ag, Au and Ag@Au nanoparticles, prepared via alkoxide mild reduction in water

  • Ortiz, Pedro D.
  • Castillo Rodriguez, Judith
  • Díaz García, Alicia M.
  • Martin Trasanco, Rudy
  • Zarate, Ximena
  • Benito, Mónica
  • Molins, Elies
  • Schott, Eduardo
Gold and silver nanoparticles were synthesized via mild alkoxide reduction of Ag+ and AuCl4- in water, under alkaline conditions. Three non-toxic polyols (glycerin, β-cyclodextrin (βCD), and a polymer (of β-cyclodextrin)) were employed in each case as reducing and capping agent. TEM analysis revealed larger nanoparticles when glycerin was used, followed by β-cyclodextrin, and finally by the polymer. Different numbers of population maxima in nanoparticles size distribution from one alkoxide to another were observed and such variation was dependent on alkoxide’s structure complexity. In UV–Vis spectra the typical bands for gold and silver nanoparticles were detected. ζ-potential measurements showed more electrostatically stable capping layer for glycerin and βCD. For the polymer, the stability of the layer should be a result of bulk effects. On the other hand, Ag-Au bi-metallic nanoparticles with core–shell structure were obtained using glycerin and β-cyclodextrin, whereas a mixture of gold and silver nanoparticles was the result with the polymer. The latter was corroborated via TEM images, EDX, UV–Vis, ζ-potential, and DLS measurements. A systematic study was carried out to elucidate the influence of the different alkoxide molecules on the properties of the resulting nanoparticles., Financial support by FONDECYT 3160144, 1201880, 1180565, ANID/FONDAP/15110019, and CONICYT doctoral fellowship number 21160394 grants is acknowledged. Millennium Science Initiative of the Ministry of Economy, Development and Tourism-Chile grant Nuclei on Catalytic Processes towards Sustainable Chemistry (CSC) is also acknowledged. ICMAB thanks the Severo Ochoa Program (MINECO, SEV- 2015-0496) Ministerio de Ciencia y Competitividad, Grant ENE2015-63969., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

1-Ethyluracil, a New Scaffold for Preparing Multicomponent Forms: Synthesis, Characterization, and Computational Studies

  • Roselló, Yannick
  • Benito, Mónica
  • Barceló Oliver, Miquel
  • Frontera, Antonio
  • Molins, Elies
In this work, we describe the successful preparation of a series of cocrystals of the modified nucleobase 1-ethyluracil with different coformers in a 1:1 or 2:1 (nucleobase:coformer) ratio including urea (URE) or some compounds containing carboxylic and hydroxyl groups such as l-malic acid (MAL), l-tartaric acid (TAR), 2-hydroxybenzoic acid (SAL), 4-hydroxybenzoic acid (4HB), and 2,4-dihydroxybenzoic acid (DHB). The influence of the hydroxyl substituent on the alkyl chain for 1·TAR and 1·SAL cocrystals or the phenyl ring for 1·SAL, 1·4HB, and 1·DHB multicomponent solids was studied. All of the compounds were characterized by powder X-ray diffraction, FT-IR, and thermal methods. Moreover, for those whose single-crystal structures could be determined, computational studies were also performed to investigate the factors that may affect the cocrystal formation, the recurrent motifs, and the energies associated with the H-bonding interactions using DFT calculations and a combination of the quantum theory of atoms in molecules (QTAIM) and the noncovalent interaction index (NCIplot) computational tools., This work has been carried out through MINECO/FEDER grant ENE2015-63969. M.B. and E.M. are grateful to the Severo Ochoa FunFuture project (MICINN, CEX2019-917S) and the Generalitat de Catalunya (2017SGR1687). M.B.-O. thanks the Vice-Rector for Research and International Relations of the University of the Balearic Islands for financial support in setting up the single-crystal X-ray diffraction facility. A.F. thanks the MICIU/AEI from Spain for financial support (Project CTQ2017-85821-R, Feder funds)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Standalone ethanol micro-reformer integrated on silicon technology for onboard production of hydrogen-rich gas

  • Pla, D
  • Salleras, Marc
  • Morata, A
  • Garbayo, Iñigo
  • Gerbolés, Marta
  • Sabaté Vizcarra, Neus
  • Divins, N J
  • Casanovas, A
  • Llorca, J
  • Tarancón, Albert
A novel design of a silicon-based micro-reformer for onboard hydrogen generation from ethanol is presented in this work. The micro-reactor is fully fabricated with mainstream MEMS technology and consists of an active low-thermal-mass structure suspended by an insulating membrane. The suspended structure includes an embedded resistive metal heater and an array of ca. 20k vertically aligned through-silicon micro-channels per square centimetre. Each micro-channel is 500 μm in length and 50 μm in diameter allowing a unique micro-reformer configuration that presents a total surface per projected area of 16 cm(2) cm(-2) and per volume of 320 cm(2) cm(-3). The walls of the micro-channels become the active surface of the micro-reformer when coated with a homogenous thin film of Rh-Pd/CeO2 catalyst. The steam reforming of ethanol under controlled temperature conditions (using the embedded heater) and using the micro-reformer as a standalone device are evaluated. Fuel conversion rates above 94% and hydrogen selectivity values of ca. 70% were obtained when using operation conditions suitable for application in micro-solid oxide fuel cells (micro-SOFCs), i.e. 750 °C and fuel flows of 0.02 mlL min(-1) (enough to feed a one watt power source)., The research was supported by Ministerio de Economía y Competitividad – Plan Nacional de I+D+i, projects POWER PACK (ENE2010-14833), ENE2012-36368, ENE2015-63969-R and BELIF (TEC2015-62519-ERC). The authors acknowledge the Ramon y Cajal (AT and NS) and Juan de la Cierva (AM) programs. NJD acknowledges UPC for a PhD grant. JL is Serra Hunter Fellow and is grateful to ICREA Academia program., Peer reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

3D printed microstructured Au/TiO2 catalyst for hydrogen photoproduction

  • Elkoro Ugarteburu, Ander|||0000-0002-0646-2674
  • Soler Turu, Lluís|||0000-0003-1591-3366
  • Llorca Piqué, Jordi|||0000-0002-7447-9582
  • Casanova Hormaechea, Ignasi|||0000-0003-0462-4147
We successfully 3D printed Au/TiO2 monoliths for photogenerating hydrogen from water/ethanol gaseous mixtures under dynamic conditions. Monolith designs were printed by additive superposition of microfilaments of titania-based pastes. Factors influencing the efficiency of the photocatalytic reactions, including impregnation of gold nanoparticles (Au NPs), calcination temperature, diameter of microfilaments and monolith design, are investigated. The use of preformed Au NPs assured a constant Au particle size (ca. 4 nm) for all samples, which allowed to a precise assessment of the effect of the design of 3D-printed titania monoliths on photocatalytic activity. The impregnation of preformed Au NPs before or after the 3D printing process has a strong influence on the photocatalytic efficiency. The pre-impregnated monoliths have a homogeneous Au NPs distribution throughout the microfilaments, whereas the post-impregnated ones present an asymmetric distribution of Au NPs, observing a high gold concentration at the surface and lower gold concentrations in the inner regions of the printed microfilaments. The gold concentration of the Au-loading suspension was reduced ca. 10 times in post-impregnated samples to ensure a similar amount of Au NPs anchored at the surface of the microfilaments, according to an XPS analysis of the pre- and post-impregnated samples. Although the photocatalytic performance of the pre-impregnated monoliths was improved when samples were calcined at 400 °C, due to a stronger contact between the Au NPs and the microfilament supports, the post-impregnated samples with 100 times lower Au concentration (0.005 wt.%) exhibited enhanced catalytic performances. Under similar geometric open section and photon absorption conditions, the photoproduction of hydrogen on a weight (or volume) basis increased strongly as the diameter of the filaments decreased, which is explained by a progressive increase of the surface-to-weight and surface-to-volume ratios. The best photoactivity was obtained with a post-impregnated titania monolith 3D printed with microfilaments with 200 µm in diameter, which yielded 0.24 mol H2 min-1 gAu-1.
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Carbonation of high-calcium fly ashes and its potential for carbon dioxide removal in coal fired power plants

  • Cwik, Agnieszka Lucyna|||0000-0002-8779-3175
  • Casanova Hormaechea, Ignasi|||0000-0003-0462-4147
  • Rodriguez Rausis, Kwon Bok
  • Koukouzas, Nikolaos
  • Zarebska, Katarzyna
Carbonation of industrial wastes rich in earth-alkali oxides is found to have a significant potential for CO2 sequestration. This process opens new perspectives not only for carbon dioxide mitigation, but also for the valorization and new applications of industrial waste materials from coal-burning power plants. In this study, mineral carbonation of high–calcium fly ash is investigated under dry and moist conditions in a continuous flow reactor during up to 2 h, at temperatures ranging from 160 to 290 °C and CO2 pressures between 1 and 6 bar. A comprehensive characterization of treated and untreated samples was carried out before and after carbonation using X-ray diffraction, X-ray fluorescence spectroscopy, thermogravimetric analysis, infrared spectroscopy and scanning electron microscopy. The maximum sequestration capacity achieved was 117.7 g CO2/kg fly ash (48.14% carbonation efficiency) under dry conditions. Results showed that increasing the pressure and temperature enhances the process of carbonation, as well as the presence of moderate amounts of water vapor in the CO2 gas flow. Newly formed carbonates were always present in the treated samples. This study shows that about 21% of all CO2 emissions of a coal-burning power plant could potentially be sequestered as carbonates., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Partial oxidation of methane to syngas using Co/Mg and Co/Mg-Al oxide supported catalysts

  • Moral, A.
  • Reyero, I.
  • Llorca Piqué, Jordi|||0000-0002-7447-9582
  • Bimbela, F.
  • Gandía, L. M.
Partial oxidation of methane (POM) was studied over a series of Co/Mg-Al catalysts. Various commercial hydroxides with different Mg/Al ratios were used as precursors of the oxides employed as catalytic supports, as well as MgO prepared in the laboratory. The effects of Co loading, Mg content, and calcination temperature (400–750¿°C) were studied on the POM reaction. The catalytic performance was evaluated at 800¿°C in a fixed-bed tubular quartz reactor under a high space velocity of 300¿L N CH4/(gcat¿h) and a O2/CH4 molar ratio of 0.5. A very high activity was obtained during 4¿h on-stream with a 20¿wt. % Co catalyst prepared with a Mg-Al mixed oxide support having a MgO content of 63¿wt. %. This catalyst gave CH4 conversions (91.3%) very close to the maximum corresponding to the thermodynamic equilibrium. Such notable performance could be attained with the catalyst precursor subjected to calcination at 500¿°C for 6¿h and subsequent in situ reduction under H2 flow at 800¿°C for 2¿h. Two main types of deactivation mechanisms were generally observed in most of the samples that suffered either a very rapid cobalt re-oxidation upon their exposure to the POM reaction atmosphere or significant deposition of carbonaceous deposits of different kinds. The characterization of the spent samples by transmission electron microscopy (TEM) revealed the presence of carbon deposits of different nature in the Mg/Al samples having a high MgO content, including filamentous carbon (whiskers), onion-shell like sheets and/or amorphous encapsulating layers. Conversely, no carbon deposits were observed in the spent Co/MgO catalyst, which underwent oxidation of the relatively less dispersed surface Co sites to form clearly defined crystals of Co oxides with particle diameters typically ranging between 25 and 100¿nm., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Carbonation of high-Ca fly ashes under flue gas conditions: implications for their valorization in the construction industry

  • Rodriguez Rausis, Kwon Bok
  • Cwik, Agnieszka Lucyna|||0000-0002-8779-3175
  • Casanova Hormaechea, Ignasi|||0000-0003-0462-4147
  • Zarebska, Katarzyna
The utilization of high-calcium fly ashes (HCFA) from coal-fired power plants in the construction industry is problematic, since their high free lime contents can lead to durability problems. In this research, the carbonation of a high-CaO fly ash has been carried out using simulated flue gas and concentrated CO2, with the aim to assess the valorization potential of such materials in the construction industry. The results show that, at 7 bars total pressure, an up to 36% carbonation efficiency can be achieved in just 30 min when pure CO2 is used; a comparable result with flue gas requires about 4 h of reaction. On the other hand, experiments carried out at atmospheric pressure show significantly different carbonation efficiencies depending on the CO2 concentration of the gas used. All experiments resulted in a substantial reduction in the original free lime content, and after reaction times of 4 h (at atmospheric pressure) and pressures of 7 bars (for any reaction time >30 min), the final free lime values were low enough to comply with the requirements of European Standards for their utilization as additions in cement., This work has been partially funded by the Government of Catalonia through the FI-2017 program for the recruitment of early-stage researchers. Contract number: 2017 FI_B00129 (K.R.) and by the Erasmus Mundus Joint Doctoral Programme on Environomical Pathways to Sustainable Energy Services (SELECTp; A. C.). Grant ENE2015-63969-C3-1-R (Spanish Government; IC co-I) and AGH grant number 16.16.210.476 (KZ)., Peer Reviewed, Objectius de Desenvolupament Sostenible::13 - Acció per al Clima, Objectius de Desenvolupament Sostenible::7 - Energia Assequible i No Contaminant
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

CO2 sorption and regeneration properties of fly ash zeolites synthesized with the use of differentiated methods

  • Czuma, Natalia
  • Casanova Hormaechea, Ignasi|||0000-0003-0462-4147
  • Baran, Pawel
  • Szczurowski, Jakub
  • Zarebska, Katarzyna
Production of fly ash zeolites may be an attractive method for the utilization of solid wastes from the energy sector. Different methods of synthesis often yield a variety of zeolite types, thereby affecting the properties of the resulting materials. The attention paid to carbon dioxide emission reduction technologies fully justifies the study of the sorption behaviours of fly ash zeolites synthesized by different methods. This work investigates the sorption properties of fly ash zeolites synthesized with different methods using CO2. Sorption capacity and adsorption isotherms were determined following the volumetric method and textural parameters were resolved according to the Dubinin-Astakhov (DA) method. The CO2 sorption capacity was in the range 0.24–4.16¿mmol/g. The relationships between structure and sorption behaviour were studied for each synthesis method. Some strong similarities between commercial zeolites and fly ash zeolites were found. The mechanism for sorption was proved to be physisorption which is fully reversible under selected conditions. The observed trends were used to identify the best sorbent., Peer Reviewed
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Partial oxidation of methane to syngas using Co/Mg and Co/Mg-Al oxide supported catalysts

  • Moral, A.
  • Reyero, I.
  • Llorca Piqué, Jordi
  • Bimbela, F.
  • Gandía, L. M.
Partial oxidation of methane (POM) was studied over a series of Co/Mg-Al catalysts. Various commercial hydroxides with different Mg/Al ratios were used as precursors of the oxides employed as catalytic supports, as well as MgO prepared in the laboratory. The effects of Co loading, Mg content, and calcination temperature (400–750¿°C) were studied on the POM reaction. The catalytic performance was evaluated at 800¿°C in a fixed-bed tubular quartz reactor under a high space velocity of 300¿L N CH4/(gcat¿h) and a O2/CH4 molar ratio of 0.5. A very high activity was obtained during 4¿h on-stream with a 20¿wt. % Co catalyst prepared with a Mg-Al mixed oxide support having a MgO content of 63¿wt. %. This catalyst gave CH4 conversions (91.3%) very close to the maximum corresponding to the thermodynamic equilibrium. Such notable performance could be attained with the catalyst precursor subjected to calcination at 500¿°C for 6¿h and subsequent in situ reduction under H2 flow at 800¿°C for 2¿h. Two main types of deactivation mechanisms were generally observed in most of the samples that suffered either a very rapid cobalt re-oxidation upon their exposure to the POM reaction atmosphere or significant deposition of carbonaceous deposits of different kinds. The characterization of the spent samples by transmission electron microscopy (TEM) revealed the presence of carbon deposits of different nature in the Mg/Al samples having a high MgO content, including filamentous carbon (whiskers), onion-shell like sheets and/or amorphous encapsulating layers. Conversely, no carbon deposits were observed in the spent Co/MgO catalyst, which underwent oxidation of the relatively less dispersed surface Co sites to form clearly defined crystals of Co oxides with particle diameters typically ranging between 25 and 100¿nm., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

3D printed microstructured Au/TiO2 catalyst for hydrogen photoproduction

  • Elkoro Ugarteburu, Ander
  • Soler Turu, Lluís
  • Llorca Piqué, Jordi
  • Casanova Hormaechea, Ignasi
We successfully 3D printed Au/TiO2 monoliths for photogenerating hydrogen from water/ethanol gaseous mixtures under dynamic conditions. Monolith designs were printed by additive superposition of microfilaments of titania-based pastes. Factors influencing the efficiency of the photocatalytic reactions, including impregnation of gold nanoparticles (Au NPs), calcination temperature, diameter of microfilaments and monolith design, are investigated. The use of preformed Au NPs assured a constant Au particle size (ca. 4 nm) for all samples, which allowed to a precise assessment of the effect of the design of 3D-printed titania monoliths on photocatalytic activity. The impregnation of preformed Au NPs before or after the 3D printing process has a strong influence on the photocatalytic efficiency. The pre-impregnated monoliths have a homogeneous Au NPs distribution throughout the microfilaments, whereas the post-impregnated ones present an asymmetric distribution of Au NPs, observing a high gold concentration at the surface and lower gold concentrations in the inner regions of the printed microfilaments. The gold concentration of the Au-loading suspension was reduced ca. 10 times in post-impregnated samples to ensure a similar amount of Au NPs anchored at the surface of the microfilaments, according to an XPS analysis of the pre- and post-impregnated samples. Although the photocatalytic performance of the pre-impregnated monoliths was improved when samples were calcined at 400 °C, due to a stronger contact between the Au NPs and the microfilament supports, the post-impregnated samples with 100 times lower Au concentration (0.005 wt.%) exhibited enhanced catalytic performances. Under similar geometric open section and photon absorption conditions, the photoproduction of hydrogen on a weight (or volume) basis increased strongly as the diameter of the filaments decreased, which is explained by a progressive increase of the surface-to-weight and surface-to-volume ratios. The best photoactivity was obtained with a post-impregnated titania monolith 3D printed with microfilaments with 200 µm in diameter, which yielded 0.24 mol H2 min-1 gAu-1., Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Carbonation of high-calcium fly ashes and its potential for carbon dioxide removal in coal fired power plants

  • Cwik, Agnieszka Lucyna
  • Casanova Hormaechea, Ignasi
  • Rodriguez Rausis, Kwon Bok
  • Koukouzas, Nikolaos
  • Zarebska, Katarzyna
Carbonation of industrial wastes rich in earth-alkali oxides is found to have a significant potential for CO2 sequestration. This process opens new perspectives not only for carbon dioxide mitigation, but also for the valorization and new applications of industrial waste materials from coal-burning power plants. In this study, mineral carbonation of high–calcium fly ash is investigated under dry and moist conditions in a continuous flow reactor during up to 2 h, at temperatures ranging from 160 to 290 °C and CO2 pressures between 1 and 6 bar. A comprehensive characterization of treated and untreated samples was carried out before and after carbonation using X-ray diffraction, X-ray fluorescence spectroscopy, thermogravimetric analysis, infrared spectroscopy and scanning electron microscopy. The maximum sequestration capacity achieved was 117.7 g CO2/kg fly ash (48.14% carbonation efficiency) under dry conditions. Results showed that increasing the pressure and temperature enhances the process of carbonation, as well as the presence of moderate amounts of water vapor in the CO2 gas flow. Newly formed carbonates were always present in the treated samples. This study shows that about 21% of all CO2 emissions of a coal-burning power plant could potentially be sequestered as carbonates., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Carbonation of high-Ca fly ashes under flue gas conditions: implications for their valorization in the construction industry

  • Rodriguez Rausis, Kwon Bok
  • Cwik, Agnieszka Lucyna
  • Casanova Hormaechea, Ignasi
  • Zarebska, Katarzyna
The utilization of high-calcium fly ashes (HCFA) from coal-fired power plants in the construction industry is problematic, since their high free lime contents can lead to durability problems. In this research, the carbonation of a high-CaO fly ash has been carried out using simulated flue gas and concentrated CO2, with the aim to assess the valorization potential of such materials in the construction industry. The results show that, at 7 bars total pressure, an up to 36% carbonation efficiency can be achieved in just 30 min when pure CO2 is used; a comparable result with flue gas requires about 4 h of reaction. On the other hand, experiments carried out at atmospheric pressure show significantly different carbonation efficiencies depending on the CO2 concentration of the gas used. All experiments resulted in a substantial reduction in the original free lime content, and after reaction times of 4 h (at atmospheric pressure) and pressures of 7 bars (for any reaction time >30 min), the final free lime values were low enough to comply with the requirements of European Standards for their utilization as additions in cement., This work has been partially funded by the Government of Catalonia through the FI-2017 program for the recruitment of early-stage researchers. Contract number: 2017 FI_B00129 (K.R.) and by the Erasmus Mundus Joint Doctoral Programme on Environomical Pathways to Sustainable Energy Services (SELECTp; A. C.). Grant ENE2015-63969-C3-1-R (Spanish Government; IC co-I) and AGH grant number 16.16.210.476 (KZ)., Peer Reviewed, Objectius de Desenvolupament Sostenible::13 - Acció per al Clima, Objectius de Desenvolupament Sostenible::7 - Energia Assequible i No Contaminant, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

CO2 sorption and regeneration properties of fly ash zeolites synthesized with the use of differentiated methods

  • Czuma, Natalia
  • Casanova Hormaechea, Ignasi
  • Baran, Pawel
  • Szczurowski, Jakub
  • Zarebska, Katarzyna
Production of fly ash zeolites may be an attractive method for the utilization of solid wastes from the energy sector. Different methods of synthesis often yield a variety of zeolite types, thereby affecting the properties of the resulting materials. The attention paid to carbon dioxide emission reduction technologies fully justifies the study of the sorption behaviours of fly ash zeolites synthesized by different methods. This work investigates the sorption properties of fly ash zeolites synthesized with different methods using CO2. Sorption capacity and adsorption isotherms were determined following the volumetric method and textural parameters were resolved according to the Dubinin-Astakhov (DA) method. The CO2 sorption capacity was in the range 0.24–4.16¿mmol/g. The relationships between structure and sorption behaviour were studied for each synthesis method. Some strong similarities between commercial zeolites and fly ash zeolites were found. The mechanism for sorption was proved to be physisorption which is fully reversible under selected conditions. The observed trends were used to identify the best sorbent., Peer Reviewed, Postprint (published version)
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Ligand Migration from Cluster to Support, A Crucial Factor for Catalysis by Thiolate-protected Gold Clusters

  • Zhang, Bei
  • Sels, Annelies
  • Salassa, Giovanni|||0000-0002-2396-3884
  • Pollitt, Stephan
  • Truttmann, Vera
  • Rameshan, Christoph|||0000-0002-6340-4147
  • Llorca, Jordi|||0000-0002-7447-9582
  • Olszewski, Wojciech|||0000-0002-4682-4326
  • Rupprechter, Günther|||0000-0002-8040-1677
  • Bürgi, Thomas|||0000-0003-0906-082X
  • Barrabés, Noelia|||0000-0002-6018-3115
Thiolate protected metal clusters are valuable precursors for the design of tailored nanosized catalysts. Their performance can be tuned precisely at atomic level, e. g. by the configuration/type of ligands or by partial/complete removal of the ligand shell through controlled pre-treatment steps. However, the interaction between the ligand shell and the oxide support, as well as ligand removal by oxidative pre-treatment, are still poorly understood. Typically, it was assumed that the thiolate ligands are simply converted into SO, CO and HO. Herein, we report the first detailed observation of sulfur ligand migration from Au to the oxide support upon deposition and oxidative pre-treatment, employing mainly S K-edge XANES. Consequently, thiolate ligand migration not only produces clean Au cluster surfaces but also the surrounding oxide support is modified by sulfur-containing species, with pronounced effects on catalytic properties.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

NiSn bimetallic nanoparticles as stable electrocatalysts for methanol oxidation reaction

  • Li, Junshan|||0000-0002-1482-1972
  • Luo, Zhishan|||0000-0002-0801-9238
  • Zuo, Yong|||0000-0003-1564-467X
  • Liu, Junfeng|||0000-0003-3164-6472
  • Zhang, Ting|||0000-0002-0317-9662
  • Tang, PengYi|||0000-0002-2306-095X
  • Arbiol i Cobos, Jordi|||0000-0002-0695-1726
  • Llorca, Jordi|||0000-0002-7447-9582
  • Cabot i Codina, Andreu|||0000-0002-7533-3251
Nickel is an excellent alternative catalyst to high cost Pt and Pt-group metals as anode material in direct methanol fuel cells. However, nickel presents a relatively low stability under operation conditions, even in alkaline media. In this work, a synthetic route to produce bimetallic NiSn nanoparticles (NPs) with tuned composition is presented. Through co-reduction of the two metals in the presence of appropriate surfactants, 3-5 nm NiSn NPs with tuned Ni/Sn ratios were produced. Such NPs were subsequently supported on carbon black and tested for methanol electro-oxidation in alkaline media. Among the different stoichiometries tested, the most Ni-rich alloy exhibited the highest electrocatalytic activity, with mass current density of 820 mA mg⁻¹ at 0.70 V (vs. Hg/HgO). While this activity was comparable to that of pure nickel NPs, NiSn alloys showed highly improved stabilities over periods of 10,000 s at 0.70 V. We hypothesize this experimental fact to be associated to the collaborative oxidation of the byproducts of methanol which poison the Ni surface or to the prevention of the tight adsorption of these species on the Ni surface by modifying its surface chemistry or electronic density of states.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Compositionally tuned NixSn alloys as anode materials for lithium-ion and sodium-ion batteries with a high pseudocapacitive contribution

  • Li, Junshan|||0000-0002-1482-1972
  • Xu, Xijun
  • Luo, Zhishan|||0000-0002-0801-9238
  • Zhang, Chaoqi|||0000-0002-0357-235X
  • Yu, Xiaoting|||0000-0003-0457-4047
  • Zuo, Yong|||0000-0003-1564-467X
  • Zhang, Ting|||0000-0002-0317-9662
  • Tang, PengYi|||0000-0002-2306-095X
  • Arbiol i Cobos, Jordi|||0000-0002-0695-1726
  • Llorca, Jordi|||0000-0002-7447-9582
  • Liu, Jun|||0000-0001-5288-3042
  • Cabot i Codina, Andreu|||0000-0002-7533-3251
Nickel tin alloy nanoparticles (NPs) with tuned composition NixSn (0.6 ≤ x ≤ 1.9) were synthesized by a solution-based procedure and used as anode materials for Li-ion batteries (LIBs) and Na-ion batteries (SIBs). Among the compositions tested, Ni₀₉Sn-based electrodes exhibited the best performance in both LIBs and SIBs. As LIB anodes, Ni₀₉Sn-based electrodes delivered charge-discharge capacities of 980 mAh g⁻¹ after 340 cycles at 0.2 A g⁻¹ rate, which surpassed their maximum theoretical capacity considering that only Sn is lithiated. A kinetic characterization of the charge-discharge process demonstrated the electrode performance to be aided by a significant pseudocapacitive contribution that compensated for the loss of energy storage capacity associated to the solid-electrolyte interphase formation. This significant pseudocapacitive contribution, which not only translated into higher capacities but also longer durability, was associated to the small size of the crystal domains and the proper electrode composition. The performance of NixSn-based electrodes toward Na-ion storage was also characterized, reaching significant capacities above 200 mAh g⁻¹ at 0.1 A g⁻¹ but with a relatively fast fade over 120 continuous cycles. A relatively larger pseudocapacitive contribution was obtained in Ni Sn-based electrodes for SIBs when compared with LIBs, consistently with the lower contribution of the Na ion diffusion associated to its larger size.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Colloidal Ni2-, XCoxP nanocrystals for the hydrogen evolution reaction

  • Liu, Junfeng|||0000-0003-3164-6472
  • Wang, Zhenxing|||0000-0001-5083-0975
  • David, Jérémy|||0000-0003-3219-149X
  • Llorca, Jordi|||0000-0002-7447-9582
  • Li, Junshan|||0000-0002-1482-1972
  • Yu, Xiaoting|||0000-0003-0457-4047
  • Shavel, Alexey|||0000-0002-3995-0391
  • Arbiol i Cobos, Jordi|||0000-0002-0695-1726
  • Meyns, Michaela|||0000-0003-2476-9001
  • Cabot i Codina, Andreu|||0000-0002-7533-3251
A cost-effective and scalable approach was developed to produce monodisperse NiCoP nanocrystals (NCs) with composition tuned over the entire range (0 ≤ x ≤ 2). NiCoP NCs were synthesized using low-cost, stable and low-toxicity triphenyl phosphite (TPP) as a phosphorus source, metal chlorides as metal precursors and hexadecylamine (HDA) as a ligand. The synthesis involved the nucleation of amorphous Ni-P and its posterior crystallization and simultaneous incorporation of Co. The composition, size and morphology of the NiCoP NCs could be controlled simply by varying the ratio of Ni and Co precursors and the amounts of TPP and HDA. Ternary NiCoP-based electrocatalysts exhibited enhanced electrocatalytic activity toward the hydrogen evolution reaction (HER) compared to binary phosphides. In particular, NiCoP electrocatalysts displayed the lowest overpotential of 97 mV at J = 10 mA cm and an excellent long-term stability. DFT calculations of the Gibbs free energy for hydrogen adsorption at the surface of NiCoP NCs showed NiCoP to have the most appropriate composition to optimize this parameter within the whole NiCoP series. However, the hydrogen adsorption energy was demonstrated not to be the only parameter controlling the HER activity in NiCoP.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Colloidal Ni-Co-Sn nanoparticles as efficient electrocatalysts for the methanol oxidation reaction

  • Li, Junshan|||0000-0002-1482-1972
  • Luo, Zhishan|||0000-0002-0801-9238
  • He, Feng
  • Zuo, Yong|||0000-0003-1564-467X
  • Zhang, Chaoqi|||0000-0002-0357-235X
  • Liu, Junfeng|||0000-0003-3164-6472
  • Yu, Xiaoting|||0000-0003-0457-4047
  • Du, Ruifeng
  • Zhang, Ting|||0000-0002-0317-9662
  • Infante Carrió, María F.
  • Tang, PengYi|||0000-0002-2306-095X
  • Arbiol i Cobos, Jordi|||0000-0002-0695-1726
  • Llorca, Jordi|||0000-0002-7447-9582
  • Cabot i Codina, Andreu|||0000-0002-7533-3251
The deployment of direct methanol fuel cells requires engineering cost-effective and durable electrocatalysts for the methanol oxidation reaction (MOR). As an alternative to noble metals, Ni-based alloys have shown excellent performance and good stability toward the MOR. Herein, we present a series of NiCoSn colloidal nanoparticles (NPs) with composition tuned over the entire Ni/Co range (0 ≤ x ≤ 3). We demonstrate electrodes based on these ternary NPs to provide improved catalytic performance toward the MOR in an alkaline medium when compared with binary NiSn NPs. A preliminary composition optimization resulted in NiCoSn NP-based electrodes exhibiting extraordinary mass current densities, up to 1050 mA mg, at 0.6 V vs. Hg/HgO in 1.0 M KOH containing 1.0 M methanol. This current density was about two-fold higher than that of NiSn electrodes (563 mA mg). The excellent performance obtained with the substitution of small amounts of Ni by Co was concomitant with an increase of the surface coverage of active species and an enhancement of the diffusivity of the reaction limiting species. Additionally, saturation of the catalytic activity at higher methanol concentrations was measured for NiCoSn NP-based electrodes containing a small amount of Co when compared with binary NiSn NPs. While the electrode stability was improved with respect to elemental Ni NP-based electrodes, the introduction of small amounts of Co slightly decreased the cycling performance. Additionally, Sn, a key element to improve stability with respect to elemental Ni NPs, was observed to slowly dissolve in the presence of KOH. Density functional theory calculations on metal alloy surfaces showed the incorporation of Co within the NiSn structure to provide more effective sites for CO and CHOH adsorption. However, the relatively lower stability could not be related to CO or CHOH poisoning.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

SnP nanocrystals as anode materials for Na-ion batteries

  • Liu, Junfeng|||0000-0003-3164-6472
  • Wang, Shutao|||0000-0002-1689-2272
  • Kravchyk, Kostiantyn
  • Ibáñez, Maria|||0000-0001-5013-2843
  • Krumeich, Frank|||0000-0001-5625-1536
  • Widmer, Roland
  • Nasiou, Déspina
  • Meyns, Michaela|||0000-0003-2476-9001
  • Llorca, Jordi|||0000-0002-7447-9582
  • Arbiol i Cobos, Jordi|||0000-0002-0695-1726
  • Kovalenko, Maksym V.|||0000-0002-6396-8938
  • Cabot i Codina, Andreu|||0000-0002-7533-3251
Tin monophosphide is a layered material consisting of Sn-P-P-Sn sandwiches that are stacked on top of each other to form a three dimensional crystallographic structure. Its composition and crystal structure makes it an excellent candidate anode material for sodium-ion batteries (SIBs). However, SnP is yet to be explored for such and other applications due to its challenging synthesis. In the present work, we report the synthesis of SnP nanocrystals (NCs) from the reaction of hexamethylphosphorous triamide (HMPT) and a tin phosphonate prepared from tin oxalate and a long chain phosphonic acid. SnP NCs obtained from this reaction displayed a spherical geometry and a trigonal crystallographic phase with a superstructure attributed to ordered diphosphorus pairs. Such NCs were mixed with carbon black and used as anode materials in SIBs. SIBs based on SnP NCs and sodium(i) bis(fluorosulfonyl)imide (NaFSI) electrolyte displayed a high reversible capacity of 600 mA h g at a current density of 100 mA g and cycling stability for over 200 cycles. Their excellent cycling performance is associated with both the small size of the crystal domains and the particular composition and phase of SnP which prevent mechanical disintegration and major phase separation during sodiation and desodiation cycles. These results demonstrate SnP to be an attractive anode material for sodium ion batteries.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Co-Sn Nanocrystalline Solid Solutions as Anode Materials in Lithium-Ion Batteries with High Pseudocapacitive Contribution

  • Li, Junshan|||0000-0002-1482-1972
  • Xu, Xijun
  • Luo, Zhishan|||0000-0002-0801-9238
  • Zhang, Chaoqi|||0000-0002-0357-235X
  • Zuo, Yong|||0000-0003-1564-467X
  • Zhang, Ting|||0000-0002-0317-9662
  • Tang, PengYi|||0000-0002-2306-095X
  • Infante Carrió, María F.
  • Arbiol i Cobos, Jordi|||0000-0002-0695-1726
  • Llorca, Jordi|||0000-0002-7447-9582
  • Liu, Jun|||0000-0001-5288-3042
  • Cabot i Codina, Andreu|||0000-0002-7533-3251
Co-Sn solid-solution nanoparticles with Sn crystal structure and tuned metal ratios were synthesized by a facile one pot solution-based procedure involving the initial reduction of a Sn precursor followed by incorporation of Co within the Sn lattice. These nanoparticles were used as anode materials for Li-ion batteries. Among the different compositions tested, Co Sn and Co Sn electrodes provided the highest capacities with values above 1500 mAh g at a current density of 0.2 A g after 220 cycles, and up to 800 mAh g at 1.0 A g after 400 cycles. Up to 81 % pseudocapacitance contribution was measured for these electrodes at a sweep rate of 1.0 mV s , thereby indicating fast kinetics and long durability. The excellent performance of Co-Sn nanoparticle alloy-based electrodes was attributed to both the small size of the crystal domains and their suitable composition, which buffered volume changes of Sn and contributed to a suitable electrode restructuration.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Solution-Processed Ultrathin SnS2-Pt Nanoplates for Photoelectrochemical Water Oxidation

  • Zuo, Yong|||0000-0003-1564-467X
  • Liu, Yongpeng|||0000-0002-4544-4217
  • Li, Junshan|||0000-0002-1482-1972
  • Du, Ruifeng
  • Yu, Xiaoting|||0000-0003-0457-4047
  • Xing, Congcong|||0000-0001-7674-6720
  • Zhang, Ting|||0000-0002-0317-9662
  • Yao, Liang
  • Arbiol i Cobos, Jordi|||0000-0002-0695-1726
  • Llorca, Jordi|||0000-0002-7447-9582
  • Sivula, Kevin|||0000-0002-8458-0270
  • Guijarro, Néstor|||0000-0002-3277-8816
  • Cabot i Codina, Andreu|||0000-0002-7533-3251
Tin disulfide (SnS ) is attracting significant interest because of the abundance of its elements and its excellent optoelectronic properties in part related to its layered structure. In this work, we specify the preparation of ultrathin SnS nanoplates (NPLs) through a hot-injection solution-based process. Subsequently, Pt was grown on their surface via in situ reduction of a Pt salt. The photoelectrochemical (PEC) performance of such nanoheterostructures as photoanode toward water oxidation was tested afterwards. Optimized SnS -Pt photoanodes provided significantly higher photocurrent densities than bare SnS and SnS -based photoanodes of previously reported study. Mott-Schottky analysis and PEC impedance spectroscopy (PEIS) were used to analyze in more detail the effect of Pt on the PEC performance. From these analyses, we attribute the enhanced activity of SnS -Pt photoanodes reported here to a combination of the very thin SnS NPLs and the proper electronic contact between Pt nanoparticles (NPs) and SnS .
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Porous NiTiO3/TiO2 nanostructures for photocatatalytic hydrogen evolution

  • Xing, Congcong|||0000-0001-7674-6720
  • Liu, Yongpeng|||0000-0002-4544-4217
  • Zhang, Yu|||0000-0002-0332-0013
  • Liu, Junfeng|||0000-0003-3164-6472
  • Zhang, Ting|||0000-0002-0317-9662
  • Tang, PengYi|||0000-0002-2306-095X
  • Arbiol i Cobos, Jordi|||0000-0002-0695-1726
  • Soler, Lluís|||0000-0003-1591-3366
  • Sivula, Kevin|||0000-0002-8458-0270
  • Guijarro, Néstor|||0000-0002-3277-8816
  • Wang, Xiang
  • Li, Junshan|||0000-0002-1482-1972
  • Du, Ruifeng
  • Zuo, Yong|||0000-0003-1564-467X
  • Cabot i Codina, Andreu|||0000-0002-7533-3251
  • Llorca, Jordi|||0000-0002-7447-9582
We present a strategy to produce porous NiTiO/TiO nanostructures with excellent photocatalytic activity toward hydrogen generation. In a first step, nickel-doped TiO needle bundles were synthesized by a hydrothermal procedure. Through the sintering in air of these nanostructures, porous NiTiO/TiO heterostructured rods were obtained. Alternatively, the annealing in argon of the nickel-doped TiO needle bundles resulted in NiO/TiO elongated nanostructures. Porous NiTiO/TiO structures were tested for hydrogen evolution in the presence of ethanol. Such porous heterostructures exhibited superior photocatalytic activity toward hydrogen generation, with hydrogen production rates up to 11.5 mmol h g at room temperature. This excellent performance is related here to the optoelectronic properties and geometric parameters of the material.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Chromium phosphide CrP as highly active and stable electrocatalysts for oxygen electroreduction in alkaline media

  • Liu, Junfeng|||0000-0003-3164-6472
  • Yu, Xiaoting|||0000-0003-0457-4047
  • Du, Ruifeng
  • Zhang, Chaoqi|||0000-0002-0357-235X
  • Zhang, Ting|||0000-0002-0317-9662
  • Llorca, Jordi|||0000-0002-7447-9582
  • Arbiol i Cobos, Jordi|||0000-0002-0695-1726
  • Wang, Ying
  • Meyns, Michaela|||0000-0003-2476-9001
  • Cabot i Codina, Andreu|||0000-0002-7533-3251
Catalysts for oxygen reduction reaction (ORR) are key components in emerging energy technologies such as fuel cells and metal-air batteries. Developing low-cost, high performance and stable electrocatalysts is critical for the extensive implementation of these technologies. Herein, we present a procedure to prepare colloidal chromium phosphide CrP nanocrystals and we test their performance as ORR electrocatalyst. CrP-based catalysts exhibited remarkable activities with a limiting current density of 4.94 mA cm at 0.2 V, a half-potential of 0.65 V and an onset potential of 0.8 V at 1600 rpm, which are comparable to commercial Pt/C. Advantageously, CrP-based catalysts displayed much higher stabilities and higher tolerances to methanol in alkaline solution. Using density functional theory calculations, we demonstrate CrP to provide a very strong chemisorption of O that facilitates its reduction and explains the excellent ORR performance experimentally demonstrated.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Graphene-supported palladium phosphide PdP2 nanocrystals for ethanol electrooxidation

  • Liu, Junfeng|||0000-0003-3164-6472
  • Luo, Zhishan|||0000-0002-0801-9238
  • Li, Junshan|||0000-0002-1482-1972
  • Yu, Xiaoting|||0000-0003-0457-4047
  • Llorca, Jordi|||0000-0002-7447-9582
  • Nasiou, Déspina
  • Arbiol i Cobos, Jordi|||0000-0002-0695-1726
  • Meyns, Michaela|||0000-0003-2476-9001
  • Cabot i Codina, Andreu|||0000-0002-7533-3251
We present a procedure to produce single-phase PdP nanocrystals (NCs). The approach involves the reaction of palladium(II) acetylacetonate and hexamethylphosphoroustriamide to nucleate defective Pd P nanoparticles that subsequently, with further phosphorous incorporation, crystallize into PdP . The synthesized PdP NCs were supported on reduced graphene oxide (rGO) and applied as electrocatalysts for ethanol oxidation. The activity of PdP toward the ethanol oxidation reaction (EOR) was over a threefold higher than that of Pd NCs prepared under similar conditions. Even better performance was obtained from PdP NCs supported on rGO, which showed current densities up to 51.4 mA cm and mass activities of 1.60 A mg , that is 4.8 and 15 times higher than Pd NCs. Besides, PdP NCs and PdP /rGO catalysts showed improved stability during EOR than Pd NCs and Pd/rGO.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Superior methanol electrooxidation performance of (110)-faceted nickel polyhedral nanocrystals

  • Li, Junshan|||0000-0002-1482-1972
  • Zuo, Yong|||0000-0003-1564-467X
  • Liu, Junfeng|||0000-0003-3164-6472
  • Wang, Xiang
  • Yu, Xiaoting|||0000-0003-0457-4047
  • Du, Ruifeng
  • Zhang, Ting|||0000-0002-0317-9662
  • Infante Carrió, María F.
  • Tang, PengYi|||0000-0002-2306-095X
  • Arbiol i Cobos, Jordi|||0000-0002-0695-1726
  • Llorca, Jordi|||0000-0002-7447-9582
  • Luo, Zhishan|||0000-0002-0801-9238
  • Cabot i Codina, Andreu|||0000-0002-7533-3251
We present the synthesis of (110)-faceted nickel polyhedral nanocrystals (NCs) and their characterization as electrocatalysts for the methanol oxidation reaction (MOR). Ni NCs were produced at 180 °C through the reduction in solution of a Ni salt. They were combined with carbon black and Nafion and deposited over glassy carbon to study their electrocatalytic properties. Electrodes based on (110)-faceted Ni NCs displayed a first order reaction with KOH in the concentration range from 0.1 M to 1.0 M. These electrodes were characterized by higher coverages of active species, but lower diffusion coefficients of the species limiting the reaction rate when compared with electrodes prepared from spherical Ni NCs. Overall, electrodes based on faceted Ni NCs displayed excellent performance with very high current densities, up to 61 mA cm, and unprecedented mass activities, up to 2 A mg, at 0.6 V vs. Hg/HgO in 1.0 M KOH containing 1.0 M methanol. These electrodes also displayed a notable stability. While they suffered an activity loss of ca. 30% during the first 10000 s of operation, afterward activity stabilized at very high current densities, ∼35 mA cm, and mass activities, ∼1.2 A mg, with only a 0.5% decrease during operation from 20000 to 30000 s.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

A low temperature solid state reaction to produce hollow MnxFe3-xO4 nanoparticles as anode for lithium-ion batteries

  • Yu, Xiaoting|||0000-0003-0457-4047
  • Zhang, Chaoqi|||0000-0002-0357-235X
  • Luo, Zhishan|||0000-0002-0801-9238
  • Zhang, Ting|||0000-0002-0317-9662
  • Liu, Junfeng|||0000-0003-3164-6472
  • Li, Junshan|||0000-0002-1482-1972
  • Zuo, Yong|||0000-0003-1564-467X
  • Jacas Biendicho, Jordi|||0000-0001-5981-6168
  • Llorca, Jordi|||0000-0002-7447-9582
  • Arbiol i Cobos, Jordi|||0000-0002-0695-1726
  • Morante, Joan Ramon|||0000-0002-4981-4633
  • Cabot i Codina, Andreu|||0000-0002-7533-3251
Hollow MnFeO nanoparticles (NPs) with an average size of 15 nm are produced from the solid state reaction of FeO-MnO heterostructures. These heterostructures are synthesized through the seeded-growth of MnO crystal domains on the surface of hollow FeO NPs obtained by the nanoscale Kirkendall effect. FeO-MnO heterostructures are subsequently annealed at 500 °C, enough temperature to promote the interfusion of Fe and Mn ions, but without compromising the hollow geometry. MnFeO nanostructures are tested as anode in lithium-ion batteries (LIBs), delivering large lithium storage capacities and high-rate capabilities of 1054 mAh g at 0.1 A g and 369 mAh g at 5 A g. Additionally, hollow MnFeO NPs display long cycling stability, with a capacity up to 887 mAh g at 0.3 A g after 450 cycles. The excellent performance of hollow MnFeO NPs as anode for LIBs is associated with their crystal structure, composition, and the presence of carbonized ligands, which further promote electrical conductivity and buffer the volume changes during cycling. Additionally, the small particle size and hollow morphology improves the lithium kinetics, structural stability and cycling performance.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Topochemical nitridation of Sr2FeMoO6

  • Ceravola, Roberta|||0000-0002-3785-3854
  • Frontera, Carlos|||0000-0002-0091-4756
  • Oró-Solé, Judith|||0000-0002-3755-4950
  • Black Serra, Ashley Phillip|||0000-0001-7929-5144
  • Ritter, Clemens
  • Mata, Ignasi|||0000-0002-4835-9659
  • Molins Grau, Elies|||0000-0003-1012-0551
  • Fontcuberta, Josep|||0000-0002-7955-2320
  • Fuertes, Amparo|||0000-0001-5338-9724
The topotactic nitridation of cation ordered, tetragonal SrFeMoO in NH at moderate temperatures leads to cubic, Fm3m double perovskite oxynitride SrFeMoON where double-exchange interactions determine ferromagnetic order with T ≈ 100 K. Substitution of oxide by nitride induces bond asymmetries and local electronically driven structural distortions, which combined with Fermi level lowering restricts charge itinerancy to confined regions and preclude spontaneous long-range magnetic order. Under a magnetic field, ferromagnetic correlations expand, favoring charge delocalization and a negative magnetoresistance is observed.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Kinetic analysis and CFD simulations of the photocatalytic production of hydrogen in silicone microreactors from water-ethanol mixtures

  • Castedo, Alejandra
  • Uriz Doray, Irantzu
  • Soler, Lluís
  • Gandía Pascual, Luis
  • Llorca Piqué, Jordi
Silicone microreactors containing microchannels of 500 μm width in a single or triple stack configuration have been manufactured, coated with an Au/TiO2 photocatalyst and tested for the photocatalytic production of hydrogen from water-ethanol gaseous mixtures under UV irradiation. Computational fluid dynamics (CFD) simulations have revealed that the design of the distributing headers allowed for a homogeneous distribution of the gaseous stream within the channels of the microreactors. A rate equation for the photocatalytic reaction has been developed from the experimental results obtained with the single stack operated under different ethanol partial pressures, light irradiation intensities and contact times. The hydrogen photoproduction rate has been expressed in terms of a Langmuir-Hinshelwood-type equation that accurately describes the process considering that hydrogen is produced through the dehydrogenation of ethanol to acetaldehyde. This equation incorporates an apparent rate constant (kapp) that has been found to be proportional to the intrinsic kinetic rate constant (k), and that depends on the light intensity (I) as follows: kapp = k·I0.65. A three-dimensional isothermal CFD model has been developed in which the previously obtained kinetic equation has been implemented. The model adequately describes the production of hydrogen of both the single and triple stacks. Moreover, the specific hydrogen productions (i.e. per gram of catalyst) are very close for both stacks thus suggesting that the scaling-up of the process could be accomplished by simply numbering-up. However, small deviations between the experimental and predicted hydrogen production suggest that a fraction of the radiation is absorbed by the microreactor components which should be taken into account for scaling-up purposes., This work has been funded through MINECO grants and FEDER funding ENE2015-63969-R and ENE2015-66975-C3-1-R. JL is Serra Húnter Fellow and is grateful to ICREA Academia program. AC is grateful to MINECO for PhD grant BES-2013-065709. LS is grateful to Generalitat de Catalunya for a Beatriu de Pinós grant (2013 BP-B 00007).