Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 11
Encontrada(s) 1 página(s)

RODIN. Repositorio de Objetos de Docencia e Investigación de la Universidad de Cádiz
Publicación Artículo científico (JournalArticle)

Novel laser texturing of W-doped VO2 thin film for the improvement of luminous transmittance in smart windows application

  • Outón Porras, Javier
  • Casas Acuña, Andrea
  • Domínguez de la Vega, Manuel
  • Blanco Ollero, Eduardo
  • Delgado Jaén, Juan José
  • Ramírez del Solar, Milagrosa
El dióxido de vanadio es un material prometedor para su aplicación en ventanas inteligentes, que sufre una transición de metal a aislante, MIT, a 68ºC acompañada de una transformación de fase estructural, SPT, de VO2(M1) a VO2(R). En este estudio se han preparado dos películas finas de VO2, una dopada con W6+ y otra sin dopar. Ambos se sintetizaron mediante la ruta sol-gel asistida por polímeros. Se evaluó el efecto del dopaje sobre los parámetros termocrómicos, dando lugar a una reducción de la temperatura de transición de fase de 21°C con una capacidad de modulación IR del 20% en la muestra dopada. Además, se ha analizado mediante espectrofotometría y microscopía de fuerza atómica el efecto del dopaje sobre los parámetros termocrómicos y las propiedades nanomecánicas. Con el objetivo de recuperar la transmitancia luminosa que disminuyó a causa del dopaje, la muestra ha sido sometida a un innovador proceso de texturizado por láser. Este tratamiento con láser es capaz de aumentar la transmitancia luminosa en casi un 40% sin afectar negativamente al resto de parámetros termocrómicos. Los resultados muestran que la combinación de ambas estrategias, dopaje y texturizado con láser, conduce a la producción de películas delgadas de VO2 con baja temperatura crítica, alta capacidad de modulación solar e IR y transmitancia luminosa mejorada, con valores cercanos a los requeridos para su aplicación real en aplicaciones inteligentes. ventanas., Vanadium dioxide is a promising material for application in smart windows, which undergoes a metal-to-insulator transition, MIT, at 68ºC accompanied by a structural phase transformation, SPT, from VO2(M1) to VO2(R). In this study, two VO2 thin films, one W6+-doped and another one undoped, have been prepared. Both were synthesized via polymer-assisted sol-gel route. The effect of doping on thermochromic parameters was evaluated, giving rise to a reduction of the phase transition temperature by 21°C with an IR modulation capability of 20% in the doped sample. Additionally, doping effect on the thermochromic parameters and nanomechanical properties has been analyzed by Spectrophotometry and Atomic Force Microscopy. With the aim of recovering the luminous transmittance that decreased because of doping, the sample has been subjected to an innovative laser texturing process. This laser treatment is able to increase the luminous transmittance by almost 40% without negatively affecting the other thermochromic parameters. Results show that the combination of both strategies, doping and laser texturing, leads to the production of VO2 thin films with low critical temperature, high solar and IR modulation capacity and enhanced luminous transmittance, with values close to those required for their real application in smart windows., Ministerio de Educación y Cultura (FPU19-02638), Ministerio de Ciencia, Innovación y Universidades (proyecto EQC2018-004704-P) e IMEYMAT (proyecto PLP2020335-1).
RODIN. Repositorio de Objetos de Docencia e Investigación de la Universidad de Cádiz
Publicación Artículo científico (JournalArticle)

Conduction Mechanisms in Au/0.8 nm–GaN/n–GaAs Schottky Contacts in a Wide Temperature Range

  • Helal, Hicham
  • Benamara, Zineb
  • Wederni, Mouhamed Amine
  • Mourad, Sabrine
  • Khirouni, Kamel
  • Monier, Guillaume
  • Robert-Goumet, Christine
  • Rabehi, Abdelaziz
  • Kacha, Arslane Hatem
  • Bakkali, Hicham
  • Cervera Gontard, Lionel
  • Domínguez de la Vega, Manuel
Au/0.8 nm–GaN/n–GaAs Schottky diodes were manufactured and electrically characterized over a wide temperature range. As a result, the reverse current Iinv increments from 1 x 10^-7 A at 80 K to about 1 x 10^-5 A at 420 K. The ideality factor n shows low values, decreasing from 2 at 80 K to 1.01 at 420 K. The barrier height q b grows abnormally from 0.46 eV at 80 K to 0.83 eV at 420 K. The tunnel mechanism TFE effect is responsible for the qfi_b behavior. The series resistance Rs is very low, decreasing from 13.80 W at 80 K to 4.26 W at 420 K. These good results are due to the good quality of the interface treated by the nitridation process. However, the disadvantage of the nitridation treatment is the fact that the GaN thin layer causes an inhomogeneous barrier height., 12 páginas
RODIN. Repositorio de Objetos de Docencia e Investigación de la Universidad de Cádiz
Publicación Artículo científico (JournalArticle)

Tracking the optical constants of porous vanadium dioxide thin films during metal-insulator transition: Influence of processing conditions on their application in smart glasses

  • Outón Porras, Javier
  • Blanco Ollero, Eduardo
  • Bakkali, Hicham
  • González Leal, Juan María
  • Delgado Jaén, Juan José
  • Ramírez del Solar, Milagrosa
Vanadium dioxide (VO2) is widely recognized as a thermochromic material with great potential for application in smart glazing for energy-efficient buildings. The monoclinic (M1) VO2 phase undergoes a first-order reversible phase transition from the semiconductor to the rutile metallic state. In this study, an M1 VO2 porous film was synthesized via a polymer-assisted sol-gel route. Processing parameters, such as drying and reduction temperatures, were varied to evaluate their influence on the thermochromic behavior of VO2 and to determine the necessary trade-off between a significant thermochromic effect and high luminous transmittance. Film-silica glass-film systems with luminous transmittance close to 80% and IR solar modulation ability as large as 20% were prepared. By tracking the optical constants of the films during the thermochromic process, the changes produced at the microscopic level in the material could be correlated with its macroscopic behavior when used as an energy-saving material., Y J. Outon acknowledges the support by the Spanish Ministerio de Educacion y Cultura through grant FPU19-02638. M. Dominguez ac-knowledges the support by the Spanish Ministerio de Ciencia, Innovacion y Universidades under project EQC2018-004704-P. The authors thank the University of Cadiz and IMEYMAT for financing the mutual facilities available at the UCA R&D Central Services (SC-ICYT) and the IMEYMAT Institute project reference PLP2020335-1 respec-tively. The authors also acknowledge J. Gonzalez and F. Delgado for their assistance in the preparation of the STEM specimens.
RODIN. Repositorio de Objetos de Docencia e Investigación de la Universidad de Cádiz
Publicación Artículo científico (JournalArticle)

Low temperature growth of nanocrystalline diamond: Insight thermal property

  • Millán Barba, Josué
  • Taylor, A.
  • Bakkali, H.
  • Alcántara Puerto, Rodrigo
  • Lloret Vieira, Fernando Manuel
  • Domínguez de la Vega, Manuel
  • Mortet, V.
  • Gutiérrez Peinado, Marina
  • Araújo Gay, Daniel
  • Guzmán de Villoria, R.
One of the limitations of materials for high-power devices and structural coatings applications is heat dissipation. Diamond is a suitable material for heat distribution due to its high thermal conductivity. Nevertheless, it is usually grown at high temperature (800–1200 ◦C), which limits its use as a coating for substrates vulnerable to degradation at high temperatures. In this work, it is studied the effect of the distance between the plasma source and substrate on the growth of nanocrystalline diamond layers on silicon substrates at low temperature (<450 ◦C) by microwave linear antenna plasma enhanced chemical vapour deposition (MW-LA-PECVD) in pulse mode. The nanocrystalline diamond films have been analysed by scanning electron microscopy (SEM), atomic force microscopy (AFM) and Raman spectroscopy. Finally, the superficial thermal conductivity of the diamond layers was determined by scanning thermal microscopy-AFM (SThM-AFM)., 6 páginas
RODIN. Repositorio de Objetos de Docencia e Investigación de la Universidad de Cádiz
Publicación Artículo científico (JournalArticle)

Unveiling single-electron tunneling in nanogranular ultrathin films for sensor applications via hyperspectral conductive AFM

  • Bakkali, Hicham
  • Domínguez de la Vega, Manuel
This study maps the electrical behavior across a 7 × 7 μm2 nanogranular ultrathin Pd-ZrO2 film, revealing nonlinear I-V characteristics indicative of single-electron tunneling. Following the Coulomb blockade power law I ∼ (V − Vt)ξ with a scaling exponent ξ ≈ 1.2, these characteristics appear above the threshold voltage Vt. By modeling the nanogranular structure as a 1D array of multitunnel junctions, we demonstrate a linear relationship between Vt and tunnel channel length, allowing for a better understanding of nanoscale electrical properties and supporting the development of sensitive sensors.
RODIN. Repositorio de Objetos de Docencia e Investigación de la Universidad de Cádiz
Publicación Artículo científico (JournalArticle)

High phosphorous incorporation in (100)-oriented MP CVD diamond growth

  • Lloret Vieira, Fernando Manuel
  • Soto Portillo, Beatriz
  • Gutiérrez Peinado, Marina
  • Haenen, Ken
  • Araújo Gay, Daniel
Diamond n-type layers are crucial for the development of a new bipolar diamond-based electronic technology. However, the difficulties to incorporate impurity atoms into the diamond lattice make its growth a stage of technological research still in progress. Phosphorus doping has been carried out successfully on (111)-oriented diamond substrates, reaching high concentrations and good reproducibility. Nevertheless, such reproducible results have not been obtained for the (100) growth orientations yet, even though the (100) substrate orientation is still the most used diamond substrate for electronic applications. In this study, three samples are grown by microwave plasma-enhanced chemical vapor deposition on diamond (100)-oriented high pressure high temperature substrates. All samples are deposited with the same growth conditions except methane, which was varied between 1.5 % and 3.5 %. A different growth mechanism is observed for each of the methane content used. The step flow growth mechanism shows increased phosphorus incorporation, determined by cathodoluminescence (CL) in cross sectional view in focused ion beam preparations. This sample also shows a less rough surface and no crystal defects observable by transmission electron microscopy (TEM). That is why these growth conditions are used for the fabrication of the n-type layer of a p+/p−/n stack. Ellipsometry and TEM measurements on this sample yield a high growth rate of 3.5 μm/h with a phosphorus concentration of 4 × 1017 cm−3, estimated by CL spectroscopy. The sample shows a low density of surface defects, observed by optical microscopy. However, TEM observations show dislocations with 1/2 a〈110〉 burger vector and stacking faults with 1/3 〈111〉 displacement vector. © 2023 The Author(s)
RODIN. Repositorio de Objetos de Docencia e Investigación de la Universidad de Cádiz
Publicación Artículo científico (JournalArticle)

Controlled grain-size thermochromic VO2 coatings by the fast oxidation of sputtered vanadium or vanadium oxide films deposited at glancing angles

  • Santos Izquierdo-Bueno, Antonio Jesús
  • Lacroix, Bertrand
  • Domínguez de la Vega, Manuel
  • García Roja, Rafael
  • Martín, N.
  • Morales Sánchez, Francisco Miguel
An original, simple and cost-effective oxidation strategy to attain thermochromic vanadium dioxide thin films is reported. This two-step procedure comprises the initial deposition of DC magnetron-sputtered vanadium or vanadium oxide films by the combination of glancing angle deposition and, if needed, reactive gas pulsing process, followed by fast oxidation of such layers in air atmosphere at high temperatures. Thanks to the careful control of the thermal treatment parameters, and taking advantage of the superior reactivity of the high surface-to-volume porous deposited structures, the formation of pure VO2 (M1) layers was achieved. The comprehensive characterization of such oxidized systems by means of scanning electron microscopy, Raman spectroscopy and scanning-transmission electron microscopy techniques such as electron energy-loss spectroscopy, not only confirmed the presence of the VO2 (M1) phase, but also allowed to shed light on the key role that reaction time plays in the selective formation of vanadium dioxide films of adjustable grain size and crystallinity. The optimal conditions to stabilize thermochromic VO2 consists in using large deposition angles (85 degrees) and short oxygen pulses (<= 2 s) during the growth, followed by fast and short thermal treatments (<= 45 s with a heating rate of 42 degrees C s(-1)) in air atmosphere at 550 degrees C. The metal-to-insulator response of the accomplished VO2 layers was finally evaluated by means of temperature dependent Kelvin probe force microscopy measurements, evidencing surface potential drops at heating, greater than those reported in the literature to date for VO2 thin films., A. J. Santos would like to thank the IMEYMAT Institute and the Spanish Ministerio de Educacion y Cultura for the concessions of grants (ICARO-173873 and FPU16-04386) . The "Talent Attraction Program" of the University of Cadiz is acknowledged by supporting B. Lacroix contract code E-11-2017-0117214. University of Cadiz and IMEYMAT are also agreed by financing the mutual facilities available at the UCA R&D Central Services (SC-ICYT) , the UCA projects reference "PUENTE PR2018-040 '' and "PUENTE PR2020-003 '', and the IMEYMAT project references "LINEAS PRIORITARIAS PLP2019120-3 and PLP2021120-1 ''. This work was supported by the Spanish State R&D project (Retos y Generacion de Conocimiento) ref. PID2020-114418RB-I00/AEI/10.13039/501100011033. The regional government of Andalusia with FEDER cofunding also participates through the projects AT-5983 Trewa 1157178 and FEDER-UCA18-10788. M. Dominguez acknowledges financial support from the Spanish Ministerio de Ciencia e Innovacion under project reference EQC 2018-004704-P FEDER 2014-2020, "Modernizacion del Servicio de Microscopia de Fuerza Atomica (AFM) del IMEYMAT".
RODIN. Repositorio de Objetos de Docencia e Investigación de la Universidad de Cádiz
Publicación Artículo científico (JournalArticle)

Formation of PLGA–PEDOT: PSS Conductive Scaffolds by Supercritical Foaming

  • Montes Herrera, Antonio
  • Valor López, Diego
  • Penabad, Yaiza
  • Domínguez de la Vega, Manuel
  • Pereyra López, Clara María
  • Martínez de la Ossa Fernández, Enrique José
The usage of conjugated materials for the fabrication of foams intended to be used as therapeutic scaffolds is gaining relevance these days, as they hold certain properties that are not exhibited by other polymer types that have been regularly used until the present. Hence, this work aims to design a specific supercritical CO2 foaming process that would allow the production of porous polymeric devices with improved conductive properties, which would better simulate matrix extracellular conditions when used as therapeutic scaffolds (PLGA–PEDOT:PSS) systems. The effects of pressure, temperature, and contact time on the expansion factor, porosity, mechanical properties, and conductivity of the foam have been evaluated. The foams have been characterized by scanning electron and atomic force microscopies, liquid displacement, PBS degradation test, compression, and resistance to conductivity techniques. Values close to 40% porosity were obtained, with a uniform distribution of polymers on the surface and in the interior, expansion factors of up to 10 orders, and a wide range of conductivity values (2.2 × 10−7 to 1.0 × 10−5 S/cm) and mechanical properties (0.8 to 13.6 MPa Young’s modulus in compression test). The conductive and porous scaffolds that have been produced by supercritical CO2 in this study show an interesting potential for tissue engineering and for neural or cardiac tissue regeneration purposes due to the fact that electrical conductivity is a crucial factor for proper cell function and tissue development.
RODIN. Repositorio de Objetos de Docencia e Investigación de la Universidad de Cádiz
Publicación Artículo científico (JournalArticle)

Spectroscopic Ellipsometry Study on Tuning the Electrical and Optical Properties of Zr-Doped ZnO Thin Films Grown by Atomic Layer Deposition

  • Bohórquez, Carolina
  • Bakkali, Hicham
  • Delgado Jaén, Juan José
  • Blanco Ollero, Eduardo
  • Herrera, Manuel
  • Domínguez de la Vega, Manuel
This work reports the ellipsometry analysis of atomic layer deposition (ALD) films of ZnO doped with Zr to determine parameters like free carrier concentration and mobility. Thin films of zinc oxide (ZnO) and Zr-doped ZnO of thickness similar to 100 nm were prepared by atomic layer deposition on sapphire, SiO2/Si(100), and Si(100) substrates. Variable-angle spectroscopic ellipsometry was used to study their optical properties in the 0.5-3.5 eV spectral range. The optical constants were accurately obtained using a model that combines Drude and Tauc-Lorentz oscillators with Bruggeman effective medium approximations, allowing the inclusion of a roughness layer in the optical model. The effect of Zr doping (ca. 1.9- 4.4 atom %) was then investigated in both as- prepared samples and samples annealed in the temperature range of 100-300 degrees C. All of the films exhibited good optical transparency (ca. 70-90% in the visible region). For doping levels below 2.7 atom %, the real part of the dielectric permittivity reveals a semiconductor-to-metal transition in the near-infrared (NIR) region, as the permittivity goes from positive to negative. Besides, the plasma energy increases with increasing Zr concentration, and both resistivity and carrier concentration exhibit slightly parabolic behaviors, with a minimum of similar to 1.5 x 10(-3) Omega cm and a maximum of 2.4 x 10(20) cm(-3), respectively, at the same critical Zr concentration (2.7 atom %). In contrast, the carrier mobility decreases rapidly from 76.0 to 19.2 cm(2)/(V s) with increasing Zr content, while conductivities and carrier mobilities worsen when the annealing temperature increases, probably due to the segregation of ZnO crystals. Finally, the optical band gap is very stable, revealing its interesting independence of substrate composition and annealing temperature, as it collapses to a single master curve when band gap energy is plotted versus free carrier concentration, following the Burstein-Moss effect. Overall, the Zr-doped ZnO films studied here would be a highly desirable system for developing thermally stable transparent conductive oxides (TCOs).
RODIN. Repositorio de Objetos de Docencia e Investigación de la Universidad de Cádiz
Publicación Artículo científico (JournalArticle)

Boron-doped diamond growth on carbon fibre: Enhancing the electrical conductivity

  • Millán Barba, Josué
  • Bakkali, Hicham
  • Lloret Vieira, Fernando Manuel
  • Gutiérrez Peinado, Marina
  • Guzmán de Villoria, R.
  • Domínguez de la Vega, Manuel
  • Haenen, Ken
  • Araújo Gay, Daniel
Carbon fibre reinforced polymers (CRFP) are extensively used in many industrial applications thanks to its mechanical properties and its low weight. Nevertheless, the orthotropic character of CRFP highly reduces its applications. The transversal electrical conductivity in CRFP is two orders poorer than in the longitudinal direction. To improve their electrical properties, this work proposes the use of polycrystalline boron doped diamond (BDD) as coating of the carbon fibres (CF). BDD coating is deposited on CF surface using microwave plasma enhanced chemical vapor deposition (MPCVD) system. The BDD coating forms a rigid conductive coating around the CF as a core–shell structure. Here, an electrical characterization of both, 12,000 filaments (a tow) and a single coated filament, are carried out in the longitudinal and cross-section directions. Macro, micro and local analysis using the Kelvin method, Conductive Atomic Force Microscopy (C-AFM), and Scanning Microwave Impedance Microscopy (sMIM), were carried out to evidence the improvement of the electrical properties. Macro measurement reveals that the BDD coating decreases to half the resistivity of the CF. The BDD coating raises the local electrical conductivity of the CF by an order of magnitude with respect to the uncoated ones. sMIM maps identified BDD locations in ring-like configurations. © 2023 The Authors
RODIN. Repositorio de Objetos de Docencia e Investigación de la Universidad de Cádiz
Publicación Artículo científico (JournalArticle)

Optical Properties of Reactive RF Magnetron Sputtered Polycrystalline Cu3N Thin Films Determined by UV/Visible/NIR Spectroscopic Ellipsometry: An Eco-Friendly Solar Light Absorber

  • Márquez Navarro, Emilio José
  • Blanco Ollero, Eduardo
  • García-Gurrea, M.
  • Cintado-Puerta, M.
  • Domínguez de la Vega, Manuel
  • Ballester, Manuel
  • Manuel Delgado, José Manuel
  • Rodríguez-Tapiador, M.I.
  • Fernández, S.M.
Copper nitride ((Formula presented.)), a metastable poly-crystalline semiconductor material with reasonably high stability at room temperature, is receiving much attention as a very promising next-generation, earth-abundant, thin film solar light absorber. Its non-toxicity, on the other hand, makes it a very attractive eco-friendly (greener from an environmental standpoint) semiconducting material. In the present investigation, (Formula presented.) thin films were successfully grown by employing reactive radio-frequency magnetron sputtering at room temperature with an RF-power of 50 W, total working gas pressure of (Formula presented.), and partial nitrogen pressures of (Formula presented.) and (Formula presented.), respectively, onto glass substrates. We investigated how argon affected the optical properties of the thin films of Cu (Formula presented.) N, with the aim of achieving a low-cost solar light absorber material with the essential characteristics that are needed to replace the more common silicon that is currently in present solar cells. Variable angle spectroscopic ellipsometry measurements were taken at three different angles, (Formula presented.), (Formula presented.), and (Formula presented.), to determine the two ellipsometric parameters psi, (Formula presented.), and delta, (Formula presented.). The bulk planar (Formula presented.) layer was characterized by a one-dimensional graded index model together with the combination of a Tauc–Lorentz oscillator, while a Bruggeman effective medium approximation model with a (Formula presented.) air void was adopted in order to account for the existing surface roughness layer. In addition, the optical properties, such as the energy band gap, refractive index, extinction coefficient, and absorption coefficient, were all accurately found to highlight the true potential of this particular material as a solar light absorber within a photovoltaic device. The direct and indirect band gap energies were precisely computed, and it was found that they fell within the useful energy ranges of (Formula presented.) – (Formula presented.) eV and (Formula presented.) – (Formula presented.) eV, respectively. The atomic structure, morphology, and chemical composition of the Cu (Formula presented.) N thin films were analyzed using X-ray diffraction, atomic force microscopy, and energy-dispersive X-ray spectroscopy, respectively. The Cu (Formula presented.) N thin layer thickness, profile texture, and surface topography of the (Formula presented.) material were characterized using scanning electron microscopy.