Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 23
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Straightforward Patterning of Functional Polymers by Sequential Nanosecond Pulsed Laser Irradiation

  • Gutiérrez-Fernández, Edgar
  • Ezquerra, Tiberio A.
  • Nogales, Aurora
  • Rebollar, Esther
Laser-based methods have demonstrated to be effective in the fabrication of surface micro- and nanostructures, which have a wide range of applications, such as cell culture, sensors or controlled wettability. One laser-based technique used for micro- and nanostructuring of surfaces is the formation of laser-induced periodic surface structures (LIPSS). LIPSS are formed upon repetitive irradiation at fluences well below the ablation threshold and in particular, linear structures are formed in the case of irradiation with linearly polarized laser beams. In this work, we report on the simple fabrication of a library of ordered nanostructures in a polymer surface by repeated irradiation using a nanosecond pulsed laser operating in the UV and visible region in order to obtain nanoscale-controlled functionality. By using a combination of pulses at different wavelengths and sequential irradiation with different polarization orientations, it is possible to obtain different geometries of nanostructures, in particular linear gratings, grids and arrays of nanodots. We use this experimental approach to nanostructure the semiconductor polymer poly(3-hexylthiophene) (P3HT) and the ferroelectric copolymer poly[(vinylidenefluoride-co-trifluoroethylene] (P(VDF-TrFE)) since nanogratings in semiconductor polymers, such as P3HT and nanodots, in ferroelectric systems are viewed as systems with potential applications in organic photovoltaics or non-volatile memories., This research was funded by the Spanish State Research Agency (AEI) through projects PID2019-107514GB-I00/AEI/10.13039/501100011033 and PID2019-106125GB-I00/AEI/10.13039/501100011033., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Photoinduced Resist-free Imprinting (PRI) in fullerene thin films as revealed by Grazing Incidence Small-angle X-ray scattering

  • Gutiérrez-Fernández, Edgar
  • Rodríguez-Rodríguez, Álvaro
  • García-Gutiérrez, Mari Cruz
  • Nogales, Aurora
  • Rebollar, Esther
  • Solano, Eduardo
  • Ezquerra, Tiberio A.
9 pags., 9 figs., In this article we explore the potential of synchrotron Grazing Incidence Small Angle X-ray Scattering (GISAXS) to evaluate the extension of a Photoinduced Resist-free Imprinting (PRI) effect for grating-like Laser Induced Periodic Surface Structures (LIPSS) on spin-coated thin films of the fullerene derivative [6,6]-phenyl C-butyric acid methyl ester (PCBM). Valuable information about the nature of both the original fullerene LIPSS and of the remaining resist-free nanostructure in terms of geometry, size distribution, lattice periodicity and degree of order can be achieved by simulations of the GISAXS patterns. One of the most interesting features provided by the GISAXS analysis is the estimation of the paracrystalline distortion factor, which can be useful to evaluate the level of order in the nanostructure. Data revealed that LIPSS in PCBM films can be described as one-dimensional paracrystalline lattices with levels of order in accordance with those typically observed in LIPSS of other materials. The PRI effect leaves a qualitatively similar nanostructure but about two times more disordered than the original LIPSS one. Our results show that GISAXS is a powerful tool to characterize Resist-free Imprinting procedures of potential relevance in nanotechnology., This work has been supported by Spanish State Research Agency (AEI) through projects PID2019-107514GB-I00/AEI/10.13039/501100011033 and PID2019-106125GB-I00/AEI/10.13039/501100011033. The GISAXS experiments were performed at NCD-SWEET beamline at ALBA synchrotron with the collaboration of ALBA staff.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Photophysical and structural modulation of poly(3-hexylthiophene) nanoparticles via surfactant-polymer interaction

  • Gutiérrez-Fernández, Edgar
  • Ezquerra, Tiberio A.
  • Rebollar, Esther
  • Cui, Jing
  • Marina, Sara
  • Martín, Jaime
  • Nogales, Aurora
9 pags., 8 figs., The optical properties of poly(3-hexylthiophene-2,5-diyl) (P3HT) can be controlled by processing the polymer in the form of nanoparticles dispersed in aqueous mediums. Colloids of P3HT were prepared by two different methods: flash –or reprecipitation- and miniemulsion precipitation technique, which result in the latter case in a polymer-water system whose stability is mediated by an ionic surfactant. Both systems yield different color dispersions, thus different absorption spectra, that is explained to be caused by the influence of the surfactant on the structure of P3HT. Differential scanning calorimetry and synchrotron radiation X-ray diffraction experiments reveal the origin of these optical differences, showing evidences of the formation of a blended structure formed due to the interaction between P3HT and the ionic surfactant. This work evidences the potential use of techniques for preparing nanoparticles in water dispersions as a tool to manipulate the structure and thus, the optical properties of these materials., This work has been supported by the Spanish Ministry of Science and Innovation under the projects PID2019-107514 GB-I00/AEI/10.13039/ 501100011033 and PID2019-106125 GB- I00/AEI/10.13039/ 501100011033, and Garantía Juvenil/Fondo Europeo. We thank E. Solano for assistance and support during beamtime in ALBA. J.M. thanks MCIU for the Ramon y Cajal contract and the grant Ref. PGC2018- 094620-A-I00 and Ikerbasque Foundation for the Fellow program
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Nanostructural organization of thin films prepared by sequential dip-coating deposition of poly(butylene succinate), poly(ε-caprolactone) and their copolyesters (PBS-ran-PCL)

  • Peñas, Mario I.
  • Ocando, C.
  • Penott-Chang, E.
  • Safari, Maryam
  • Ezquerra, Tiberio A.
  • Rebollar, Esther
  • Nogales, Aurora
  • Hernández, Rebeca
  • Müller, A.J.
10 pags., 7 figs., 2 tabs., In this work, we prepare and characterize multiphasic thin films containing poly(ε-caprolactone), PCL, poly(butylene succinate), PBS, and a poly (butylene succinate-ran-ϵ-caprolactone) (PBS-ran-PCL) random copolyester. To that aim, thin films were prepared by sequential dipping of a silicon substrate into chloroform solutions of the respective polymers. The preparation method resulted in films with varying compositions of PCL and PBS components depending on the initial concentration of the dipping solutions and the number of dipping steps employed for the preparation of the samples. Atomic force microscopy (AFM), grazing incidence X-ray scattering at wide angle (GIWAXS) and scattering-type scanning near-field optical microscopy (s-SNOM) and Fourier transform infrared nanospectroscopy (nano-FTIR) were employed to characterize the films obtained. As chloroform can dissolve all components, the final composition of the film was always rich in the last deposited layer component. The thin films obtained were semicrystalline with a complex axialitic or dendritic morphology of the dominant component (that one deposited last) with traces of the other components, whose presence and location was revealed by s-SNOM/nano-FTIR., This study was supported by Spanish Ministry of Science, Innovation and Universities (MAT2017- 83014-C2-1-P, MAT2017-83014-C2-2-P, PID2019-107514 GB-I00/AEI/ 10.13039/501100011033 and PID2019-106125 GB-I00/AEI/ 10.13039/501100011033). We also acknowledge funding by Basque Government through grant IT1309-19. The authors acknowledge beamtime access at ALBA BL11 via proposal 2018072905 and the assistance of JC Martinez during the measurements. We would also like to thank the financial support provided by the BIODEST project; this project has received funding from the European Union’s Horizon 2020 research and innovation programme under the Marie Skłodowska-Curie grant agreement No. 778092. CO wants to acknowledge “Diputaci on Foral de Gipuzkoa” in the framework program “Fellows Gipuzkoa de Atracci ́on y Retenci ́on de Talento”. RH is member of the Interdisci-plinary Platform for Sustainable Plastics towards a Circular Economy (SusPlast) from the Spanish National Research Council (CSIC).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Preparation, physical properties, and applications of water-based functional polymer inks

  • Gutiérrez-Fernández, Edgar
  • Cui, Jing
  • Martínez-Tong, Daniel E.
  • Nogales, Aurora
17 pags., 8 figs., 2 tabs. -- This article belongs to the Special Issue Polymer Nanostructures: From Surfaces to Nanospheres and Nanoparticles, In this study, water-based functional polymer inks are prepared using different solvent displacement methods, in particular, polymer functional inks based on semiconducting polymer poly(3-hexylthiophene) and the ferroelectric polymer poly(vinylidene fluoride) and its copolymers with trifluoroethylene. The nanoparticles that are included in the inks are prepared by miniemulsion, as well as flash and dialysis nanoprecipitation techniques and we discuss the properties of the inks obtained by each technique. Finally, an example of the functionality of a semiconducting/ferroelectric polymer coating prepared from water-based inks is presented., This research was funded by the Ministry of Science, grant number PID2019-107514GB-I00 and the National Natural Science Foundation of China (no. 51903224).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Thin polymer films based on poly(vinyl alcohol) containing graphene oxide and reduced graphene oxide with functional properties

  • Taraghi, I.
  • Paszkiewicz, Sandra
  • Irska, Izabela
  • Szymczyk, Anna
  • Linares, Amelia
  • Ezquerra, Tiberio A.
  • Kurcz, Magdalena
  • Winkowska-Struzik, Magdalena
  • Lipińska, Ludwika
  • Kowiorski, Krystian
  • Piesowicz, Elżbieta
10 pags., 7 figs., 2 tabs., In this article, the effect of the addition of graphene oxide (GO) and reduced graphene oxide (rGO) on the mechanical properties, thermal stability, and electrical conductivity of polyvinyl alcohol (PVA) has been investigated. Different weight percentages of nanofillers ranging from 0.5 to 5 wt% have been combined with PVA. The ultrasonic technique has been applied to disperse nanofillers in the PVA solution. The nanocomposite films have been prepared via solution casting technique and the dispersion of nanofillers into the PVA has been studied through optical microscopy. The microstructure, crystallization behavior, and interfacial interaction were characterized through X-ray diffraction and Fourier transform infrared spectroscopy. Differential scanning calorimetry (DSC) and thermogravimetric analysis have been applied to study the thermal properties of the prepared nanocomposites. The DSC results revealed that the crystallization temperature and melting temperature were enhanced in the presence of GO nanofiller. Besides, the tensile strength at break was improved along with the addition of GO; however, elongation at break for PVA/GO and PVA/rGO was diminished. Moreover, all specimens showed insulating behavior and the only sample was electrically conducting, which contain a high amount of rGO (5 wt%)., Spanish Ministry of Science and Innovation, Grant/Award Number:PID2019-107514GB-I00
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Additive effect on the structure of PEDOT:PSS dispersions and its correlation with the structure and morphology of thin films

  • Gutiérrez-Fernández, Edgar
  • Ezquerra, Tiberio A.
  • García-Gutiérrez, Mari Cruz
14 pags., 7 figs., 3 tabs. -- This article belongs to the Section Polymer Physics and Theory, We reported on the interaction between poly(3,4-ethylenedioxythiophene):polystyrene sulfonate (PEDOT:PSS) and high-boiling-point additives in PEDOT:PSS aqueous dispersions and in the final polymer films with the aim of stablishing correlations between the structure of both inks and solid thin films. By Small-Angle X-ray Scattering (SAXS) using synchrotron radiation, it was found that the structural changes of dispersions of PEDOT:PSS with high-boiling-point additives can be explained as a two-step mechanism depending on the additive concentration. A compaction of PEDOT:PSS grains was observed at low concentrations while a swelling of the grains together with a phase segregation between PEDOT and PSS segments was evidenced at larger concentrations. Thin films’ morphology and structure were investigated by atomic force microscopy (AFM) and synchrotron Grazing Incidence Wide-Angle X-ray Scattering (GIWAXS) respectively. Our two-step model provides an explanation for the small and sharp domains of PE- DOT:PSS thin films observed for low-additive concentrations (first step) and larger domains and roughness found for higher-additive concentrations (second step). A reduction of the ratio of PSS in PEDOT:PSS thin films upon the presence of additives was also observed. This can be related to a thinning of the PSS shells of PEDOT:PSS grains in the dispersion. The results discussed in this work provide the basis for a controlled tuning of PEDOT:PSS thin films structure and the subsequent electrical properties., This research was funded by Spanish State Research Agency (AEI) through projects PID2019-107514GB-I00/AEI/10.13039/501100011033.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Probing structure development in Poly(vinylidene Fluoride) during “operando” 3-D printing by small and wide angle X-ray scattering

  • Ezquerra, Tiberio A.
  • Nogales, Aurora
  • García-Gutiérrez, Mari Cruz
  • Rebollar, Esther
  • Gálvez, Óscar
  • Šics, Igors
  • Malfois, Marc
12 pags., 8 figs., We have investigated the crystallization of the thermoplastic polymer Poly(vinylidene Fluoride) (PVDF) during “operando” 3D printing Fused Filament Fabrication (FFF). The performance of the 3D printing set-up and the corresponding methodology for performing simultaneous SAXS/WAXS with synchrotron radiation have been discussed. Simultaneous SAXS and WAXS experiments were performed across the printed line with a resolution of 50 μm. The experiments indicate that crystallization is faster at the polymer-air interface than in other points within the printed line. The final crystallinity varies with position being lower at both the interfaces, i.e. polymer-air (13%) and welding zone (11%), while being higher (18%) in the middle part of the printed line. Orientation of the crystalline lamellae is higher at both interfaces, suggesting higher shear rate than in the bulk of the printed line where elongational flow is dominant. The final crystallinity levels in the different locations of the printed line are relatively low, as compared with reported values in melt pressed samples (≈30%), due to the extremely fast crystallization kinetics involved in the solidification of PVDF 3D printed lines. Therefore, it is expected that 3D printed PVDF pieces will exhibit significant structural modifications due to the potential crystallization that eventually will proceed during storage because the glass transition of PVDF is well below room temperature., This work has been supported by Agencia Estatal de Investigación(AEI) through projects: PID2019 - 107514 GB - I00/AEI/10.13039/501100011033 and PID2019 - 106125 GB -I00/AEI/10.13039/501100011033. The experiments with synchrotron radiation were performed at NCD-SWEET beamline at ALBA Synchrotron with the collaboration of ALBA staff (Proposal 2020024176).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Micropatterned functional interfaces on elastic substrates fabricated by fixing out of plane deformations

  • Nogales, Aurora
  • García Sánchez, Carolina
  • Campo, Ángel Adolfo del
  • Ezquerra, Tiberio A.
  • Rodríguez-Hernández, Juan
We report on the preparation of micropatterned functional surfaces produced by inducing an out-of-plane deformation on elastic substrates and fixing these by creating a rigid oxidized top layer. Specifically, the elastic substrate used was Polydimethylsiloxane (PDMS) and the rigid layer on top was created by ozonation of this material. We evidenced that the surface pattern formed is directly dependent on the pressure applied, the mechanical properties of the elastic substrate and on the dimensions and shape of the mask employed to define the exposed and non-exposed areas. In addition to the pattern formed, another interesting aspect is related to the ozone diffusion within the material. Softer PDMS enables more efficient diffusion and produced a thicker oxidized layer in comparison to rigid PDMS. Finally, a simulation was carried out using the distribution of Von Misses stresses of a solid plate to understand the conditions in which the applied force resulted in the rupture of the rigid oxidized layer under a permanent deformation., The authors gratefully acknowledge support from the Consejo Superior de Investigaciones Científicas (CSIC). Equally, this work was financially supported by the Ministerio de Ciencia e Innovación (MICINN) (Grants RTI2018-096328-B-I00 and PID2019-107514GB-I00/AEI/10.13039/501100011033).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Contribución de congreso (ConferenceOutput)

Is the sub-glass temperature relaxation of furan-based polymers related to their high gas barrier properties?

  • Ezquerra, Tiberio A.
  • Nogales, Aurora
  • García-Gutiérrez, Mari Cruz
  • Linares, Amelia
  • Gálvez, Óscar
  • Toledano, Óscar
  • Hermoso, Francisco Javier
  • Sanz, Mikel
  • Santoro, Gonzalo
  • Rebollar, Esther
  • Irska, Izabela
  • Paszkiewicz, Sandra
  • Szymczyk, Anna
11th Conference on Broadband Dielectric Spectroscopy and its Applications (BDS2022), Donostia/San Sebastián, 04.Sep - 09.Sep 2022. -- Presentación con 25 diapositivas, Poly(alkylene 2,5-furanoate)s, (PAF)s, are fully biobased homopolyesters based on 2,5-furandicarboxylic acid that have recently emerged as promising alternative to petroleum based poly(alkylene terephthalate)s. In addition to a lower production carbon footprint poly(alkylene 2,5-furanoate)s have received significant attention due to their outstanding gas barrier properties in comparison to traditional poly aromatic esters [1]. The influence of chain dynamics on barrier properties has also devoted some attention. Dielectric spectroscopy experiments performed in poly(trimethylene 2,5-furanoate) revealed that the subambient relaxation, below its glass transition temperature, exhibited an inhibition of the mode corresponding to the ester oxygen linked to the aliphatic subunit which efficiently relaxes in the poly(trimethylene terephthalate) counterpart [2]. Fourier Transform Infrared (FT-IR) spectroscopy can provide precise information of intra-molecular motions at the molecular level [3]. By evaluating the vibrational frequencies and the corresponding oscillator, strength from the IR spectra information about the intra-molecular dynamics can be available. In this study, we present a combined IR spectroscopy and BDS study focused on the sub-glass temperature molecular dynamics of poly(trimethylene 2,5-furanoate) in comparison to that of poly(trimethylene terephthalate) in order to shed light on the influence the dynamics on the barrier properties of Poly(alkylene 2,5-furanoate)s., The authors gratefully acknowledge the financial support of the Spanish Ministry of Science and Innovation (MICINN) through PID2019-107514GB-I00 / AEI / 10.13039/501100011033.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Crystallization and phase separation in PEDOT:PSS/PEO blend thin films: Influence on mechanical and electrical properties at the nanoscale

  • Sanviti, Matteo
  • Martínez-Tong, Daniel E.
  • Rebollar, Esther
  • Ezquerra, Tiberio A.
  • García-Gutiérrez, Mari Cruz
Thin films of polymeric blends composed of poly(3,4-ethylenedioxythiophene) polystyrene sulfonate (PEDOT:PSS) and polyethylene oxide (PEO) were investigated by varying the concentration of the two components over the entire range of compositions and the molecular weight of PEO. Phase separation and crystallization have been studied at different length scales by combining Atomic Force Microscopy (AFM) and Grazing Incidence Wide Angle X-ray Scattering (GIWAXS) using synchrotron light. Several different arrangements in the thin films of the two polymers constituting the blend were observed and discussed in detail, providing information about their reciprocal influence at the micro- and nano-scale. In addition to that, we were able to estimate quantitative nanomechanical and nanoelectrical properties via AFM and finally revealing the dependence of the thin films' physical properties on their composition and structure. By varying the blend composition, we achieved different coating capability, mechanical properties, and electrical conductivity. Furthermore, depending on the PEO molecular weight, the electrical response of the resulting blends’ thin films shows some differences. In the low range concentration, the blend thin films with high molecular weight PEO present coarser conducting paths than in those with the low molecular weight counterparts. For intermediate concentrations, a more effective phase segregation of PEDOT:PSS and PEO is achieved for high molecular weight PEO. These differences are also translated to different electrical conductivity., We acknowledge funding from the Spanish State Research Agency (AEI) through projects PID2019-107514 GB-I00/AEI/10.13039/501100011033 and PID2019-106125 GB-I00/AEI/10.13039/501100011033. We also acknowledge funding from Eusko Jaurlaritza (Basque Government) through the Grants IT-1566-22., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Development of polar phases in ferroelectric poly(vinylidene fluoride) (PVDF) nanoparticles

  • Gutiérrez-Fernández, Edgar
  • Sena-Fernández, Jose
  • Rebollar, Esther
  • Ezquerra, Tiberio A.
  • Hermoso-Pinilla, Francisco J.
  • Sanz, Mikel
  • Gálvez, Óscar
  • Nogales, Aurora
7 pags., 6 figs., Ferroelectric polymer nanoparticles of poly(vinylidene fluoride) (PVDF) were prepared by dialysis nanoprecipitation. Particles with mean diameter of 230 nm show piezoelectric response as observed by Piezoresponse Force Microscopy (PFM). The origin of this ferroelectric behavior has been attributed to the presence of ferroelectrically active crystalline phases of PVDF in the nanoparticles (mainly β and γ phases) as demonstrated by differential scanning calorimetry (DSC) and temperature dependent Fourier transform infrared spectroscopy (FTIR) and X ray diffraction. The combination of the preparation method and temperature treatment can provide a method for tuning the ferroelectricity in PVDF homopolymer nanoparticles., The authors gratefully acknowledge the financial support of the Spanish Ministry of Science and Innovation (MICINN) through projects PID2019-107514GB-I00/AEI/10.13039/501100011033 and PID2019-106125GB-I00/AEI/10.13039/501100011033. Also, ‘Programa Operativo de Empleo Juvenil’ (YEI) Comunidad de Madrid (CAM, PEJ-2019-AI/TIC-15699). The synchrotron experiments were performed at NCD-SWEET beamline at ALBA Synchrotron with the collaboration of ALBA staff., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Influence of film thickness and substrate roughness on the formation of laser induced periodic surface structures in poly(ethylene terephthalate) films deposited over gold substrates

  • Prada-Rodrigo, Javier
  • Rodríguez-Beltrán, René I.
  • Ezquerra, Tiberio A.
  • Moreno, Pablo
  • Rebollar, Esther
10 pags., 10 figs., 4 tabs., A study of the formation of Laser Induced Periodic Surface Structures (LIPSS) using near-infrared femtosecond pulsed laser irradiation on poly(ethylene terephthalate) (PET) films deposited over gold substrates has been carried out. We report the influence of the gold substrate roughness and the PET film thickness on LIPSS formation and analyze it in terms of the features of the electric field distribution obtained by computer simulations using COMSOLTM. We obtain LIPSS with periods close to the irradiation wavelength as long as the aforementioned substrate and film parameters remain below certain threshold values, in particular for polymer thicknesses below 200 nm and substrate roughness of few nm. However, experiments show the impossibility of LIPSS formation for rough substrates as well as thick films above these threshold values. In our numerical simulations, we notice the generation of Surface Plasmon Polariton (SPP) in the film-substrate interface that gives rise to a periodical field pattern on the surface of the thin film. This periodicity is broken for a certain level of substrate roughness or film thickness. Moreover, the evolution of the period of the SPP as the substrate roughness and film thickness change for given laser parameters is qualitatively in good agreement with the experimental LIPSS period (below but close to the irradiation laser wavelength). In conclusion, the experimental findings are explained by the formation and behavior of SPP in the thin film-substrate interface. On these grounds, we propose that, for our case of study, this SPP formation and the subsequent inhomogeneous rise in temperature induced by the periodic field on the surface of the sample is the leading mechanism contributing to LIPSS formation., Funding: This work was supported by the Spanish State Research Agency (AEI), Spain [project numbers PID2020-119003GB-I00/MCIN/AEI/10.13039/501100011033, PID2019-107514GB-I00/AEI/10.13039/501100011033, and PID2019-106125GB-I00/AEI/10.13039/501100011033] and the Junta de Castilla y León, Spain [project number SA136P20]. J.P.-R. thanks the Spanish Ministry of Universities, Spain [grant number FPU17/01859]., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Physicochemical Modifications on Thin Films of Poly(Ethylene Terephthalate) and Its Nanocomposite with Expanded Graphite Nanostructured by Ultraviolet and Infrared Femtosecond Laser Irradiation

  • Rodríguez-Beltrán, René I.
  • Prada-Rodrigo, Javier
  • Crespo Solana, Ana
  • Ezquerra, Tiberio A.
  • Moreno, Pablo
  • Rebollar, Esther
16 pags., 9 figs., 4 tabs. -- This article belongs to the Special Issue Carbon-Based Polymer Composites, In this work, the formation of laser-induced periodic surface structures (LIPSS) on the surfaces of thin films of poly(ethylene terephthalate) (PET) and PET reinforced with expanded graphite (EG) was studied. Laser irradiation was carried out by ultraviolet (265 nm) and near-infrared (795 nm) femtosecond laser pulses, and LIPSS were formed in both materials. In all cases, LIPSS had a period close to the irradiation wavelength and were formed parallel to the polarization of the laser beam, although, in the case of UV irradiation, differences in the formation range were observed due to the different thermal properties of the neat polymer in comparison to the composite. To monitor the modification of the physicochemical properties of the surfaces after irradiation as a function of the laser wavelength and of the presence of the filler, different techniques were used. Contact angle measurements were carried out using different reference liquids to measure the wettability and the solid surface free energies. The initially hydrophilic surfaces became more hydrophilic after ultraviolet irradiation, while they evolved to become hydrophobic under near-infrared laser irradiation. The values of the surface free energy components showed changes after nanostructuring, mainly in the polar component. Additionally, for UV-irradiated surfaces, adhesion, determined by the colloidal probe technique, increased, while, for NIR irradiation, adhesion decreased. Finally, nanomechanical properties were measured by the PeakForce Quantitative Nanomechanical Mapping method, obtaining maps of elastic modulus, adhesion, and deformation. The results showed an increase in the elastic modulus in the PET/EG, confirming the reinforcing action of the EG in the polymer matrix. Additionally, an increase in the elastic modulus was observed after LIPSS formation., This research was funded by the Spanish State Research Agency (AEI), grant numbers PID2020-119003GB-I00/MCIN/AEI/10.13039/501100011033, PID2019-107514GB-I00/AEI/10.13039/ 501100011033, PID2019-106125GB-I00/AEI/10.13039/501100011033, and Junta de Castilla y León (project number SA136P20). J.P.-R. thanks the Spanish Ministry of Universities (grant number FPU17/01859), Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Supramolecular structure, relaxation behavior and free volume of bio-based poly(butylene 2,5-furandicarboxylate)-block-poly(caprolactone) copolyesters

  • Paszkiewicz, Sandra
  • Irska, Izabela
  • Zubkiewicz, Agata
  • Walkowiak, Konrad
  • Rozwadowski, Zbigniew
  • Dryzek, Jerzy
  • Linares, Amelia
  • Nogales, Aurora
  • Ezquerra, Tiberio A.
14 pags., 14 figs., 6 tabs., In the present study, a fully plant-based sustainable copolyester series, namely poly(butylene 2,5-furandicarboxylate)-block-poly(caprolactone)s (PBF-block-PCL)s were successfully synthesized by melt polycondensation combining butylene 2,5-furandicarboxylate with polycaprolactone diol (PCL) at different weight ratios. Differential scanning calorimetry (DSC) showed that only PBF underwent melting, crystallization from the melt, and cold crystallization. Thermogravimetric analysis (TGA) revealed outstanding thermal stability, exceeding 305 °C, with further improvement in thermal and thermo-oxidative stability with increasing PCL content. Broadband dielectric spectroscopy (BDS) revealed that at low temperatures, below the glass transition (Tg) all copolyesters exhibited two relaxation processes (β1 and β2), whereas the homopolymer PBF exhibited a single β-relaxation, which is associated with local dynamics of the different chemical bonds present in the polymer chain. Additionally, it was proved that an increase in PCL content affected the dynamics of the chain making it more flexible, thus providing an increase in the value of the room temperature free volume fractions (fv) and the value of elongation at break. These effects are accompanied by a decrease in hardness, Young's modulus, and tensile strength. The described synthesis enables a facile approach to obtain novel fully multiblock biobased copolyesters based on PBF and PCL polyesters with potential industrial implementation capabilities., This work has been supported by Spanish State Research Agency (AEI) through projects PID2019-107514GB-I00/AEI/ 10.13039/501100011033., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Inter and intra molecular dynamics in poly(trimethylene 2,5-furanoate) as revealed by infrared and Broadband Dielectric Spectroscopies

  • Gálvez, Óscar
  • Toledano, Óscar
  • Hermoso, Francisco Javier
  • Linares, Amelia
  • Sanz, Mikel
  • Rebollar, Esther
  • Nogales, Aurora
  • García-Gutiérrez, Mari Cruz
  • Santoro, Gonzalo
  • Irska, Izabela
  • Paszkiewicz, Sandra
  • Szymczyk, Anna
  • Ezquerra, Tiberio A.
9 pags., 9 figs., 2 tabs., Infrared spectroscopy (IR) and Broadband Dielectric Spectroscopy (BDS) experiments have been performed in poly(trimethylene 2,5-furanoate)(PTF) and poly(trimethylene terephthalate)(PTT) below their glass transition temperatures. The BDS experiments reveal a richer inter-molecular dynamic for PTT as characterized by a multimodal β relaxation in contrast with the monomodal one exhibited by PTF. The evolution with temperature of comparable IR absorption bands is very similar for PTF and PTT and shows small shifts in wavenumbers towards lower values, with exception of the band related to the stretching mode of the carbonyl group. In addition, a significant difference appears in the shape of the bands associated with the –C[dbnd]O stretching. While for PTT the absorption feature is comprised of a single component, that for PTF exhibits several components suggesting the presence of hydrogen bonds. This effect may be responsible for the monomodal shape of the β relaxation of PTF since a higher degree of intramolecular coupling between the furan ring and the rest of the monomer is expected. Density Functional Theory (DFT) calculations support the experimental results revealing that as temperature increases an increment of the syn conformations of the 2,5-furandicarboxylic acid (FDCA) moiety is likely to occur in the amorphous state. The energy gain from more stable anti to less stable syn isomers can be compensated by the formation of hydrogen bonds between interchain FDCA moieties in syn conformations. This effect may cause additional hindrance to the intermolecular dynamics of the dielectric β relaxation. It is conceivable that the hindrance exhibited by PTF in both intra and inter-molecular dynamics may play a role in the reduction of gas diffusion and permeability of PTF in comparison with PTT., Grants PID2019-107514 GB-I00/AEI/10.13039/501100011033 and PID2019-106125 GB-I00/AEI/10.13039/501100011033 funded by MCIN/AEI/10.13039/501100011033 and by “ ERDF A way of making Europe”. GS acknowledges grant RYC2020-029810-I funded by MCIN/ AEI/10.13039/501100011033 and by “ ESF Investing in your future”. SP would like to thank for financial support from the National Science Centre within project SONATA no 2018/31/D/ST8/00792. A
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

3D Printing-Assisted Nanoimprint Lithography of Polymers

  • Martínez-García, Patricia
  • Rebollar, Esther
  • Nogales, Aurora
  • García-Gutiérrez, Mari Cruz
  • Sena-Fernández, Jose
  • Ezquerra, Tiberio A.
5 pags., 7 figs., Fused filament fabrication, commonly referred to as 3D printing, is an additive manufacturing method finding plenty of applications nowadays. In contrast, polymer nanopatterning by nanolithographic techniques plays an important role in obtaining functional surfaces and coatings for applications in different fields including micro- and nanoelectronics. In spite of their relevance, additive manufacturing and polymer nanolithography have not found yet a common niche to be developed. Although both approaches are oriented to achieve different types of objects, it is shown that the confluence of both technologies can be desirable and potentially convenient. Herein, it is demonstrated that by employing conventional 3D printing, it is possible to fabricate nanostructured polymer surfaces in a relatively simple way by using similar approaches as those used in nanoimprint lithography but without the need for clean room conditions. To do that, a printed-assisted nanoimprint lithography concept (3DPrANIL) has been tested for different types of polymer and silicon templates. It is demonstrated that a polymeric nanostructured hydrophilic template can be replicated accurately on another polymer rendering a nanostructured surface with enhanced hydrophobicity. The results support 3DPrANIL as novel method to obtain micro- and nanostructured surfaces with different functionalities like iridescence and hydrophobicity., This study was funded by AEI /10.13039 /501100011033/ Unión EuropeaNextGenerationEU/PRTR (grants PID2019-107514GB-I00/AEI/10.13039/501100011033, PID2019-106125GB-I00/ AEI/10.13039/501100011033,and TED2021-129845B-I00). Dr. G. Doerk is gratefully acknowledged(Center for Functional Nanomaterials, Brookhaven National Laboratory,USA) for the support in the preparation of silicon molds. The synchrotronexperiments were performed at NCD-SWEET beamline at ALBASynchrotron with the collaboration of M. Malfois and I.Šics., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Dewetting Effects in Poly(vinylidene fluoride-trifluoroethylene) Thin Films on Poly(3-hexylthiophene) Substrates

  • Cui, Jing
  • Rebollar, Esther
  • Ezquerra, Tiberio A.
  • Nogales, Aurora
7 pags., 5 figs., 1 tab., Bilayers of ferroelectric polymers [poly(vinylidene fluoride-trifluoroethylene), PVDF-TrFE] on semiconducting poly(3-hexylthiophene) (P3HT) substrates have been prepared by sequential spin coating. When creating thin layers of PVDF-TrFE from its solution in methyl ether ketone (MEK), they exhibit dewetting in the form of holes for thicker P3HT substrates, whereas they form continuous layers on thinner P3HT substrates. The dispersive and polar components of the surface tension of the different P3HT substrates were obtained through contact angle measurements. An estimation of the shape of the disjoining pressure as a function of thickness of a liquid film of MEK on top of the different P3HT substrates was obtained. Through these estimations, we observe that the stability region for continuous film formation shifts toward higher thicknesses for the samples where experimentally the holes are observed. This work provides understanding on the mechanism of stable film formation and effective tools to control the formation of holes, in functional polymer bilayers, of special importance in the fabrication of organic thin film-based devices., The authors gratefully acknowledge the financial support of the Spanish Ministry of Science and Innovation (MICINN) through projects PID2019-107514GB-I00/AEI/10.13039/501100011033 and PID2019-106125GB-I00/AEI/10.13039/501100011033, the Key Scientific Research Project of Henan province (18A430004), and the group innovation space project of ZZULI (2017ZCKJ214). Previous experiments performed by J.C. during her PhD inspired this work. The description of these experiments in J.C thesis is similar to the description of the experiments on this manuscript. J.C. also acknowledges the China Scholarship Council for funding her research during her stay at IME-CSIC (File No. 201207040083)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Effect of film thickness on laser induced surface structures formation on optically transparent polymer films

  • Cui, Jing
  • Nogales, Aurora
  • Ezquerra, Tiberio A.
  • Rebollar, Esther
9 pags., 9 figs., Laser-induced periodic surface structures can be prepared on polymer thin films, despite the absence of light absorption at the wavelength of the irradiating laser, by using a bilayer approach. Nanostructuring of a poly(3-hexylthiophene-2,5-diyl) (P3HT) layer, by laser irradiation at 532 nm, covered by a thin layer of a non-absorbing polymer, in this case, the ferroelectric copolymer poly(vinylidene fluoride - trifluoro ethylene),P(VDF-TrFE), allows the development of a grating-like structure on the surface. The range of thicknesses of the upper layer, which leads to the formation of LIPSS, has been determined. It is verified that for a thickness larger than 40 nm, no periodic structures are formed, neither in the upper layer nor in the bottom P3HT one. This can be explained considering a mechanical restriction which prevents P3HT rearrangement. The upper nanostructured surface layer exhibits ferroelectric properties as proven by piezoresponse force microscopy measurements., This research was funded by the Spanish State Research Agency (AEI) through projects PID2019-107514 GB-I00/AEI/10.13039/501100011033 and PID2019-106125 GB-I00/AEI/10.13039/501100011033. The assistance of D. Hermida from ESRF is gratefully acknowledged. J.C also acknowledges the China Scholarship Council for funding her research during her stay at IEM-CSIC (File No 201207040083)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Study of the crystal structure and hydrogen bonding during cold crystallization of Poly(trimethylene 2,5-furanoate)

  • Toledano, Óscar
  • Galvez, Óscar
  • Sanz, Mikel
  • García-Arcos, Carlos
  • Rebollar, Esther
  • Nogales, Aurora
  • García-Gutiérrez, Mari Cruz
  • Santoro, Gonzalo
  • Irska, I.
  • Paszkiewicz, S.
  • Szymczyk, A.
  • Ezquerra, Tiberio A.
12 pags., 11 figs., 2 tabs., Here, we present a detailed description of the in situ isothermal crystallization of poly(trimethylene 2,5-furandicarboxylate)(PTF) as revealed by real-time Fourier transform infrared spectroscopy (FTIR) and grazing incidence wide-angle X-ray scattering (GIWAXS). From FTIR experiments, the evolution of hydrogen bonding with crystallization time can be monitored in real time, while from GIWAXS, crystal formation can be followed. Density functional theory (DFT) calculations have been used to simulate FTIR spectra for different theoretical structures, enabling a precise band assignment. In addition, based on DFT ab initio calculations, the influence of hydrogen bonding on the evolution with crystallization time can be understood. Moreover, from DFT calculations and comparison with both FTIR and GIWAXS experiments, a crystalline structure of poly(trimethylene 2,5-furandicarboxylate) is proposed. Our results demonstrate that hydrogen bonding is present in both the crystalline and the amorphous phases and its rearrangement can be considered as a significant driving force for crystallization of poly(alkylene 2,5-furanoate)s., This work was supported by grants PID2019-107514GB-I00/AEI/10.13039/501100011033, PID2019-106125GB-I00/AEI/10.13039/501100011033, and TED2021-131914B−I00 andTED2021-129845B−I00 funded by MCIN/AEI/10.13039/501100011033 and by “ERDF A way of making Europe”. G.S.acknowledges grant RYC2020-029810-I funded by MCIN/AEI/10.13039/501100011033 and by “ESF Investing in yourfuture”. O.T. acknowledges support from the Spanish Ministry of Universities with European Union funds Next GenerationEU through a Margarita Salas fellowship. S.P. would like to thank them for financial support from the National Science Centre within project SONATA no. 2018/31/D/ST8/00792.The authors acknowledge J.P. Sánchez for technical supportand E. Solano and M. Malfois for support in the experimentsperformed in NCD-SWEET beamline at ALBA synchrotron(Cerdanyola del Vallès, Barcelona, Spain) with the collabo-ration of ALBA staff.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Laser-Induced Periodic Surface Structures in Polymers with Tailored Laser Fields

  • de Nalda, R.
  • Corrales, Maria Eugenia
  • Recio, Pedro
  • Casasús, Ignacio M.
  • Bañares, Luis
  • Ezquerra, Tiberio A.
  • Rebollar, Esther
7 pags., 4 figs., In this work, laser-induced periodic surface structures (LIPSS) are generated on the surface of thin films of poly(trimethylene terephthalate) (PTT) fabricated by spin coating on silicon. Previous studies have shown the appearance of LIPSS in this type of materials with femtosecond laser pulses in the near-infrared region of the spectrum, despite the extremely low absorption of the polymer. The present work consists of an exploration of the effect of adding complexity to the femtosecond laser fields employed for irradiation. Changes in the repetition rate of the pulse train, the pulse duration, and the pulse temporal chirp are explored, and conditions for optimum LIPSS formation are identified. The effects of these modifications on the polymer surface topography, assessed by atomic force microscopy, are described and discussed., This work has been funded by the Spanish State Research Agency (AEI)through projects PID2019-106125GB-I00/AEI/10.13039/501100011033,PID2019-107514GB-I00/AEI/10.13039/501100011033, and PID2021-122839NB-I00. P.R. is grateful to Universidad Complutense de Madrid(UCM) for a Margarita Salas postdoctoral contract. I.M.C. is grateful tothe Spanish Ministry of Universities for an FPU predoctoral contract(FPU21/04608). We thank Sandra Paszkiewicz and Anna Szymczyk forthe preparation of the PTT. The facilities of the Center for UltrafastLasers (CLUR) of the Universidad Complutense de Madrid are rate fully acknowledged., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Tuning photophysical properties of semiconducting polymer nanoparticles for improved photocatalytic activity

  • Sena-Fernández, Jose
  • Rebollar, Esther
  • Hurtado-Mendoza, Aitana
  • Murdoch, Timothy J
  • Vega, Juan Francisco
  • Martín-Fabiani, Ignacio
  • Ezquerra, Tiberio A
  • Nogales, Aurora
9 pages, 5 figures, This study investigates the relation between the optical and structural properties of poly(3-hexylthiophene) nanoparticles with their efficiency as photocatalysts for the degradation of water pollutants. Two nanoparticle preparation methods were investigated. Our results indicate that nanoparticles prepared by the miniemulsion method are more efficient in inducing photodegradation. The higher crystallinity, observed by X-ray scattering experiments and the presence of surfactant in these nanoparticles affect the photophysical properties. The fluorescence lifetime of miniemulsion nanoparticles is shorter than that of nanoparticles prepared by the flash method, favoring charge transfer towards the surface of the nanoparticle. These charges, in the presence of water, produce highly reactive oxygen species, responsible for the pollutant photodegradation., TThis work was supported by grants PID2019-107514GB-I00, PID2022-138635NB-I00 funded by MCIN/AEI/10.13039/501100011033, by grants TED2021-131914B-I00 and TED2021-129845B-I00 funded by MCIN/AEI/10.13039/501100011033 and by “ERDF A way of making Europe”. JS acknowledge the funding by MCIN/AEI/10.13039/501100011033 through grant number PRE2020-094362 and by the Regional Government of Madrid through the project TEC MATRIX-CM (TEC-2024/TEC-85). The support from the Scientific Network on Photocatalysis OASIS funded by the Consejo Superior de Investigaciones Científicas (CSIC), Spain is also acknowledged. AHM acknowledges funding by the JAE program, CSIC. The authors acknowledge M. Malfois for support in the experiments performed in NCD-SWEET beamline at ALBA synchrotron (Cerdanyola del Vallès, Barcelona, Spain) with the collaboration of ALBA staff., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Relaxation behaviour and free volume of bio-based Poly(trimethylene terephthalate)-block-poly(caprolactone) copolymers as revealed by Broadband Dielectric and Positron Annihilation Lifetime Spectroscopies

  • Irska, Izabela
  • Paszkiewicz, Sandra
  • Pawlikowska, Daria
  • Dryzek, Jerzy
  • Linares, Amelia
  • Nogales, Aurora
  • Ezquerra, Tiberio A.
  • Piesowicz, Elżbieta
10 pages, 10 figures, 3 tables, Broadband Dielectric (BDS) and Positron Annihilation Lifetime Spectroscopies (PALS) have been used to investigate the relaxation behaviour of novel bio-based aliphatic-aromatic block copolymers based on poly (trimethylene terephthalate) (PTT) and poly (caprolactone) (PCL). Copolymerization increases the ability to crystallize of the PTT-block-PCL copolymers in relation to PTT due to a decrease of the glass transition (T<inf>g</inf>) temperatures as the amount PCL increases since PCL acts as plasticizer. The dielectric relaxation of the PTT-block -PCL copolymers is dominated by that of PTT being characterized by a α relaxation process above T<inf>g</inf> and a bimodal β relaxation below T<inf>g</inf>. The faster mode of the β relaxation has been assigned to the bond between the ester oxygen and the aliphatic carbon of the PTT block and the slower β mode has been attributed to the bond between the aromatic ring carbon to the ester carbon also in the PTT block. Both modes for the copolymers appear to be faster than those of PTT at comparable temperatures while for the copolymer series a nearly similar subglass dynamics is observed. Since free volume values for PTT and PTT-block-PCL (75/25) as measured by PALS are very similar and those for the copolymers increase with PCL content this effect is likely to be attributed to change in the flexibility of the polymeric chain upon going from PTT to the copolymers rather than to a free volume dependence confirming the local nature, i.e. non cooperative, of the β relaxation. The weak dependence of the β relaxation dynamics with PCL content for the copolymers suggests that this relaxation is mainly related to the PTT block. The α relaxation becomes faster the higher the PCL content is following the decrease of the T<inf>g</inf> with increasing PCL content. This effect is supported by the free volume and o-Ps annihilation life time for the block copolymers measured by PALS at room temperature revealing an increase of both magnitudes with PCL content. By scaling free volume and o-Ps annihilation life time with T<inf>room</inf>-T<inf>g</inf>, being T<inf>g</inf> the corresponding glass transition temperature for every copolymer, a characteristic sigmoidal variation with temperature is observed., This work has been supported by Spanish State Research Agency (AEI) through project PID2019-107514 GB-I00/AEI/10.13039/501100011033., Peer reviewed