Pasar al contenido principal

DESARROLLO DE UNA PLANTA DE POTENCIA DE OXICOMBUSTION CON CAPTURA DE CARBONO PARA PRODUCCION DE ENERGIA LIMPIA

PID2021-123351OB-I00

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal para Impulsar la Investigación Científico-Técnica y su Transferencia
Subprograma Subprograma Estatal de Generación de Conocimiento
Convocatoria Proyectos de I+D+i (Generación de Conocimiento y Retos Investigación)
Año convocatoria 2021
Plan Estatal 2021-2023 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario UNIVERSITAT POLITÈCNICA DE VALÈNCIA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 10
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Off-Design Operation of a Carbon Capture Enabler Oxy-Fuel Combustion Engine with O2 Self-Production

  • Diego
  • García-Cuevas González, Luis Miguel|||0000-0001-9340-0617
  • Arnau Martínez, Francisco José|||0000-0003-2902-0630
  • Serrano, J.R.|||0000-0003-0692-3917
  • Gutierrez-Castro, Fabio Alberto
[EN] This work examines the behaviour of a spark-ignition engine using oxy-fuel combustion, coupled with an oxygen production cycle based on a mixed ionic-electronic ceramic membrane. Through 1D-0D simulations, two compression ratios are studied: the original ratio of 9.6 and the optimised CR of 20, under various load levels and altitude conditions. The results show that operational limits exist at part-load conditions, where reducing the load without implementing additional control strategies may compromise system performance. It is observed that at low loads, the intake pressure can fall below atmospheric pressure, encouraging the presence of N2 in the combustion process. Additionally, the engine can operate efficiently up to an altitude of 4000 m, although increasing boosting is required to maintain proper membrane conditions. These findings emphasise the importance of load control and the potential need for energy assistance under certain circumstances., This work has been partially supported by Grant PID2021-123351OB-I00 funded by MCIN/AEI/10.13039/501100011033 and by ERDF/EU. This research has been partially supported by Grant CIPROM/2021/061 funded by Generalitat Valenciana. Diego Contreras has been funded by the Universitat Politècnica de València s Research and Development Support Programme (PAID-01-24).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Advanced exergy analysis of a Reverse Brayton cycle using air as working fluid for cryogenic purposes

  • Serrano, J.R.|||0000-0003-0692-3917
  • Dolz, Vicente|||0000-0003-1511-6957
  • Gómez-Vilanova, Alejandro|||0000-0002-6627-7075
  • López-Carrillo, Juan Antonio|||0000-0003-0613-6470
[EN] The global push to reduce greenhouse gas emissions has led to the ban of high global warming potential (GWP) refrigerants in the refrigeration sector, prompting the adoption of low-GWP alternatives. However, as regulations are expected to tighten, technologies like the Reverse Brayton cycles (RBC) are emerging. RBCs can operate with safe fluids and can reach very low temperatures through compressions, regeneration, and expansion, requiring only electricity. This research presents results from an RBC equipped with a radial turbine using natural air (R-729), a hazard-free fluid with zero ozone depletion potential (ODP) and emission potential. The cycle utilizes automotive components, offering a cost-effective, high-tech solution. The study evaluates the cycle COP at a design point and performs an exergetic analysis at 173K. Using a thermal and fluid dynamic model of the cycle, the critical components of the cycle influencing the COP are identified, and potential improvements are explored., The authors want to acknowledge the institution "Conselleria de Innovacion, Universidades, Ciencia y Sociedad Digital de la Generalitat Valenciana" and its grant program "Subvenciones para la contratacion de personal investigador de caracter predoctoral" for doctoral studies (CIACIF/2021/404) funded by The European Union; also the institution "Vicerrectorado de Investigacion de la Universitat Politecnica de Valencia" for the funding provided by the research project (PAID-11-22) ". This work has been partially supported by Grant PID2021-123351OB-I00 funded by MCIN/AEI/10.13039/501100011033 and, as appropriate, by "ERDF A way of making Europe".
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Modeling and Evaluation of Oxy-Combustion and In Situ Oxygen Production in a Two-Stroke Marine Engine

  • Serrano, J.R.|||0000-0003-0692-3917
  • Arnau Martínez, Francisco José|||0000-0003-2902-0630
  • Calvo, Alejandro
  • Burgos, Rossana
[EN] Considering the concerns for emissions reduction in the maritime sector, the present paper evaluates, through modeling and simulation, oxy-fuel combustion in a two-stroke ship engine (2SE) and the best production system configuration to obtain the required oxygen (O2). An initial model of a ship engine is calibrated with the engine manufacturer's data and then adapted to work with O2 as the oxidant to eliminate nitrogen oxide (NOx) emissions and with exhaust gas recirculation (EGR) to control the in-cylinder combustion temperature. Mixed Ionic-Electronic Conducting (MIEC) membranes produce the necessary O2 from the ambient air, which is heated up and pressurized by a heat exchanger and turbocharging coupled system to provide the air conditions required for the proper operation of the MIEC. Several layouts of this system are evaluated for the full load engine operating point to find the optimum O2 production system configuration. Results reveal that the engine operating under oxy-fuel combustion conditions avoids NOx emissions at the expense of higher brake-specific fuel consumption (BSFC) to obtain the original brake torque, and also expels a stream composed exclusively of CO2 and H2O, which facilitates the separation of CO2 from exhaust gases., This research has been partially supported by Grant CIPROM/2021/061 funded by Generalitat Valenciana. Also partially supported by Grant PID2021-123351OB-I00 funded by MCIN/AEI/10.13039/501100011033 and, as appropriate, by ERDF A way of making Europe . And also partially funded by Programa de Ayudas de Investigación y Desarrollo PAID-01-22, from Universitat Politècnica de València (UPV) which granted the Rossana s pre-doctoral contract.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Strategies for improving premixed oxy-fuel combustion in spark-ignition engines

  • Raggi, R.
  • Gómez-Soriano, Josep|||0000-0002-2742-9224
  • Martín, Jaime|||0000-0002-0496-3176
  • Novella Rosa, Ricardo|||0000-0002-5123-6924
[EN] Oxy-fuel combustion in internal combustion engines is a promising technology that eases Carbon Capture and Storage and allows near-zero NOx powerplants. While some experimental and theoretical studies on oxyfuel combustion engines are available in the literature, there is a lack of systematic research on dilution strategies or on the use of non-synthetic exhaust gas recirculation. This study uses a combination of 0D-1D and CFD modeling and experimental measurements to assess the use of oxygen dilution and real exhaust gas recirculation in a single-cylinder spark-ignition engine operation under oxy-fuel combustion conditions. A comparison between conventional and oxy-fuel combustion is first performed to highlight the differences between the two combustion modes. Later, taking into account the thermo-mechanical limitations and knocking restrictions, several strategies are analyzed to improve oxy-fuel combustion efficiency: exhaust gas recirculation ratio, compression ratio, and intake temperature. Results show that under oxy-fuel mode, operating at stoichiometric conditions with exhaust gas recirculation rates around 70%, reduces NOx by more than 99%, and CO and uHC by up to 89% compared to conventional combustion with air. In terms of performance, an 8 pp reduction in gross indicated efficiency could be expected; however, since knocking propensity is reduced, the compression ratio can be increased to recover about 5 pp of the efficiency drop., This work has been partially supported by Grant PID2021-123351OB-I00 funded by MCIN/AEI/10.13039/501100011033, Spain and, as appropriate, by "ERDF A way of making Europe", and by Generalitat Valenciana, Spain through the grant Santiago Grisolia GRISOLIAP/2021/108. The authors want to express their gratitude to CONVERGENT SCIENCE Inc. and Convergent Science GmbH for their kind support with the CFD calculations using the CONVERGE software. Funding for open access charge: CRUE-Universitat Politecnica de Valencia. The authors would like to thank Ing. Gabriel Alcantarilla Ballesteros for his inestimable work during the experimental campaign.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Scalable continuous-flow photocatalytic system based on a TiO2-coated sand composite for microplastic mineralization

  • Company-Doménech, Carlos|||0009-0005-7484-3996
  • Blázquez-Moraleja, Alberto|||0000-0003-1375-930X
  • Bosca Mayans, Francisco
  • Marín García, Mª Luisa|||0000-0002-9789-8894
[EN] Microplastics (MPs) represent a persistent environmental threat, with polyethylene terephthalate MPs (PET) from textiles and domestic washing posing particular challenges due to their widespread use in bottles, cleaning products, and clothing fibers. While most reported photocatalysis strategies for PET degradation rely on TiO 2 suspensions, often requiring pH adjustment or chemical additives, we present here the first continuous-flow system to achieve effective mineralization of PET directly in untreated domestic washing wastewater generated without detergent addition. Accordingly, an optimized TiO 2 and SiO UVA LED 2 -SiO layer was immobilized onto commercial sand microspheres, and the resulting materials were integrated to yield a structurally robust photocatalytic system (sand@TiO 2 2 @TiO 2 ) that synergistically combines the intrinsic mechanical filtration capacity of sand with the enhanced specific surface area provided by the TiO 2-functionalized SiO 2 microspheres. This material was thoroughly characterized using FESEM, Raman, XRD, UV¿Vis diffuse reflectance, and XPS. Its implementation in a lab-scale tubular photoreactor equipped with LED lamps (¿ max 1 =362 nm) demonstrated complete removal of PET microplastics from wastewater generated from domestic textile washing with tap water at a flow rate of 0.05 L h , as confirmed by COD, TOC, gravimetry, turbidimetry, FTIR, and microscopy. Mechanistic elucidation of PET photodegradation was achieved using EPR and LC-MS. The results of this study indicate that the sand@TiO 2-SiO 2 @TiO 2 photocatalyst is effective for the mineralization of microplastics in continuous-flow systems. This scalable strategy advances microplastic remediation by linking traditional laboratory-scale suspension photocatalysis research with real-world wastewater treatment applications. Moreover, this approach paves the way for the design of new advanced materials to improve microplastic removal., This research was supported by the Spanish Ministry of Science and Innovation through grants TED2021-131952B-I00, PDC2022-133426- I00, and CEX2021-001230-S, funded by MCIN/AEI/10.130 39/501100011033. Additional financial support was provided by the Generalitat Valenciana through the CLEAN-LAGOON project (PROMETEO/CIPROM-2024-49), the Agencia Valenciana de la Innovacion (AVI, grant 20220826/UCIE-ITQ), and the Ayuda a Primeros Proyectos de Investigacion ¿ (PAID-06-24) from the Universitat Polit`ecnica de Valencia. The authors also acknowledge the Generalitat Valenciana and the European Union for co-funding the postdoctoral contract of A.B.M. (CIAPOS/2023/201) through the European Social Fund Plus (ESF+) Operational Program 2021 2027. C.C⋅D acknowledges the Universitat Politecnica de Valencia for the Predoctoral FPI fellowship (FPI-UPV/ Subprograma 2) and the Spanish Catalysis Society for the master's thesis scholarship.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Coupling an oxygen generation cycle with an oxy-fuel combustion spark ignition engine for zero NOx emissions and carbon capture: A feasibility study

  • Serrano, J.R.|||0000-0003-0692-3917
  • Arnau Martínez, Francisco José|||0000-0003-2902-0630
  • García-Cuevas González, Luis Miguel|||0000-0001-9340-0617
  • Gutiérrez, Fabio Alberto
[EN] An oxycombustion spark-ignition engine coupled to an production cycle based on a mixed electronic-ionic ceramic-type membrane is studied in this paper. The exhaust gases drive oxygen production through a heat exchanger network and a set of turbochargers. Initially, a study at medium speed is carried out to determine the influence of the oxygen concentration and the engine compression ratio on the system performance. A 16.3 % of fuel consumption reduction is reached when 30 % of mass fraction and an engine compression ratio of 20 are implemented when compared with conventional engine operation. Then, a full load study in a wide range of engine speeds is performed, where a maximum fuel consumption reduction of 21 % is obtained at high speed (5000 rpm) comparing with conventional engine operation. The study shows the whole cycle has demonstrated promising performance parameters at different working conditions ( mass fraction, compression ratio, engine load and speed)., The authors want to acknowledge the institution "Conselleria deInnovacion, Universidades, Ciencia y Sociedad Digital de la Generalitat Valenciana"' and its grant program "Subvenciones para la contratacion de personal investigador de caracter predoctoral" for doctoral studies (ACIF/2020/246) funded by The European Union. This work has been partially supported by Grant PID2021-123351OB-I00 funded by MCIN/AEI/10.13039/501100011033 and, as appropriate, by "ERDFA way of making Europe''. In addition, this research has been also supported by Grant CIPROM/2021/061 funded by Generalitat Valenciana. Funding for open access charge: CRUE-Universitat Politecnica de Valencia.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Towards low-carbon mobility through 0D phenomenological modelling of oxy-fuel combustion in internal combustion engines

  • De Felice, Massimiliano
  • Raggi, Rodrigo
  • De Bellis, Vincenzo
  • Martín, Jaime|||0000-0002-0496-3176
[EN] Oxy-fuel combustion in internal combustion engines is gaining attention as a promising technology for carbon capture and achieving near-zero nitrogen oxides emissions, addressing global warming concerns. Recent experimental and simulation studies evaluated this unconventional combustion mode in internal combustion engines under various dilution strategies, but current models are not yet appropriately customized to describe incylinder processes with highly enriched oxygen atmospheres. This study aims to validate a Zero-Dimensional engine model, consisting of a predictive combustion model, a dedicated laminar flame speed correlation, and emission sub-models, embedded in a One-Dimensional simulation code, and to assess its capability to describe the behaviour of a gasoline-fuelled single-cylinder engine under premixed oxy-fuel combustion conditions. The experimental campaign tested the engine at medium load (from 8.3 bar to 10.1 bar of Indicated Mean Effective Pressure) and a rotational speed of 3000 rpm, varying the oxygen/fuel proportions (relative oxygen/fuel ratio from 1.0 to 1.2), exhaust gas recirculation ratios (from 66 to 75 %), and intake temperatures (70 degrees C and to 80 degrees C), and the data are used for the model calibration and validation, defining a single set of tuning constants. The combustion model replicated in-cylinder pressures and burn rates, resulting in an average error of 1.3 crank angle degrees for the combustion phasing, while the emission model replicated exhaust pollutant concentrations, with average errors with respect to experiments of 23.6 % and 13.6 % for carbon monoxide and unburned hydrocarbon, respectively. The predictive capability of the model discloses the potential applicability in the context of engine and system calibration and optimization., This work has been partially supported by Grant PID2021-123351OB-I00 funded by MCIN/AEI/10.13039/501100011033 and, as appropriate, by "ERDF A way of making Europe", and co-funded by Generalitat Valenciana through the grant Santiago Grisolia GRISOLIAP/2021/108. The authors want to express their gratitude to CONVERGENT SCIENCE Inc. and Convergent Science GmbH for their kind support with the CFD calculations using the CONVERGE software. The authors would like to thank Ing. Gabriel Alcantarilla Ballesteros for his inestimable work during the experimental campaign.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

A strategy to extend load operation map range in oxy-fuel compression ignition engines with oxygen separation membranes

  • Arnau Martínez, Francisco José|||0000-0003-2902-0630
  • Bracho Leon, Gabriela|||0000-0002-9198-7044
  • García-Cuevas González, Luis Miguel|||0000-0001-9340-0617
  • Farias, V. H.
[EN] The possibility of applying oxy-fuel combustion to a compression ignition engine (CIE) at different operating points regarding engine speed and load is studied in this work. To do so, a strategy is proposed to extend the load operation map range of a 2.2 L turbocharged and direct-injection CIE under oxy-fuel combustion conditions using mixed ionic-electronic conducting membranes (MIEC) to acquire oxygen (O2) from the air. As nitrogen is not present in the intake flow, nitrogen oxide (NOx) emissions are eliminated, and carbon capture is allowed. The strategy consists of modifying exhaust gas temperature and oxygen-fuel ratio, generating temperature-lambda maps to decide the optimal combination in terms of engine performance. Thus, the system behavior is analyzed at three engine speeds (1250 rpm, 2500 rpm and 3500 rpm) with different load levels and compression ratio (CR) of 20. The baseline engine model is calibrated with experimental data within part-load operation ranges, and an apparent combustion time model calibrated with computational fluid dynamics data is applied to simulate the combustion process under oxy-fuel combustion conditions. Finally, specific parameters are researched to verify whether the system produces enough energy to heat up the MIEC, generating the necessary oxygen. Indeed, a few of them have been found very useful as design parameters for finding out oxy-fuel engine operation limits and estimating MIEC design features., This work has been partially supported by Grant PID2021-123351OB-I00 funded by MCIN/AEI/10.13039/501100011033 and, as appropriate, by "ERDF A way of making Europe" and by Grant CIPROM/2021/061 funded by Generalitat Valenciana, Spain. In addition, this work has been also partially founded by Universitat Politecnica de Valencia, Spain (UPV-SOLGEN-7967) and Generalitat Valenciana, Spain (GRISOLIAP/2020/078).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Extension of a Zero-Dimensional Mixing-Controlled Combustion Model for the Development of a NOx Free System Based on the Oxy-Combustion Concept

  • Serrano, J.R.|||0000-0003-0692-3917
  • López, J. Javier|||0000-0002-9486-2511
  • Martín, Jaime|||0000-0002-0496-3176
  • Bracho Leon, Gabriela|||0000-0002-9198-7044
[EN] Oxy-combustion is a promising concept to achieve an extremely clean combustion, independently of the fuel type, because, on the one hand, it is a NOx-free combustion and, on the other hand, the CO2 produced during combustion can be easily captured once the water vapour is removed from the exhaust gases stream, consequently allowing also carbon neutral operation. An existing zero-dimensional (0D), mixing-controlled combustion model, developed for a standard diesel combustion scenario, has been adapted to the oxy-fuel combustion scenario. Initially, the model over-predicted the heat release at the end of the combustion process. The main model adaptation was to modify the relationship between the average YO2 and the effective YO2 (i.e. the one of the charge actually entrained by the spray), to be consistent with the significant increase in compression ratio needed in the oxy-fuel context. As a result, a model able to correctly predict the combustion behaviour at any operating condition has been obtained, which finally represents a very suitable tool to assist in the concept development., This research has been partly supported by Grant CIPROM/2021/061 funded by Generalitat Valenciana, by Grant PID2021-123351OB-I00 funded by MCIN/AEI/10.13039/501100011033 and, as appropriate, by 'ERDF A Way of Making Europe'. Finally it has also been partially supported by grant TED2021-129379A-I00 funded by the European Union Next generation EU/PRTR.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Design of a carbon capture system for oxy-fuel combustion in compression ignition engines with exhaust water recirculation

  • Luján, José M.|||0000-0001-6133-8943
  • Arnau Martínez, Francisco José|||0000-0003-2902-0630
  • Piqueras, P.|||0000-0002-3767-0839
  • Farias-Da Silva, Vitor Hugo
[EN] The oxy-fuel combustion engine concept with onboard oxygen generation and carbon capture (CC) is studied using as a starting point a baseline oxy-fuel combustion layout coupled to a mixed ionic-electronic conducting membranes for producing oxygen (O2) from the air. A CC system is designed accounting for the flash-out temperatures and the operating pressure of the last CO2 purification step. The proposed engine concept is optimized through the product of useful effective efficiency and engine brake power,which is maximized actuating on the start of injection (SOI) for every assessed gas path layouts. The additional cooling power required by the carbon capture system (CC) is also contemplated . Initially, two approaches are compared when the CC is coupled to the O2 generation unit, including or not an intake cooler. The use of intake cooler yields better engine performance than removing it but increases the cooling power requirements significantly. The extreme results from using or not the intake cooler, indicates that a proper solution could combine both cases, approaching for a different cooling concept. A mixer model is developed to recirculate part of the water condensed in the CC towards the cylinder inlet to lower the intake gas temperature and increase the oxidizer heat capacity ratio. From this layout, an optimum setup for SOI and recirculated water mass flow is found considering the trade-off between additional cooling power and engine performance. Indeed, this case reduces the total ICE additional cooling power required by the exclusive use of an intake cooler by about 27% and improves the engine performance by about 20% in comparison to the lack of intake cooling of the charge flow., This work has been partially supported by Grant PID2021-123351OB-I00 funded by MCIN/AEI/10.13039/501100011033 and, as appropriate, by "ERDF A way of making Europe". In addition, the work has been supported by Grant CIPROM/2021/061 funded by Generalitat Valenciana, Spain. Finally, the Ph.D. candidate Vitor Farias has been funded by Generalitat Valenciana, Spain (GRISOLIAP/2020/078) .