Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 35
Encontrada(s) 1 página(s)

Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Microfluidic preparation of thin film composite hollow fiber membrane modules for water nanofiltration: Up-scaling, reproducibility and MOF based layers

  • Esteras-Saz, Javier
  • Paseta, Lorena
  • Echaide-Górriz, Carlos
  • Malankowska, Magdalena
  • Luque-Alled, José M.
  • Zornoza, Beatriz
  • Téllez, Carlos
  • Coronas, Joaquín
Background The commercialization of thin film composite (TFC) hollow fiber (HF) membranes remains challenging owing to issues associated with membrane manufacturing. Methods TFC membranes were synthesized by microfluidic interfacial polymerization of polyamide (PA) on polysulfone hollow fiber (HF) membrane modules. A total of 33 HF membrane modules were prepared with different number of HFs (from 1 to 25) and different lengths (from 10 to 50 cm). They were evaluated in a nanofiltration operation in terms of water permeance and rose Bengal (RB) and MgSO4 rejections. Significant findings Among the 33 modules, 73% showed RB rejections higher than 95%, while 36% of the modules reached rejections above 99%. During the membrane synthesis, different parameters, such as PA monomer concentration, residence time and reaction time, were studied. As a result, the amount of monomer was reduced by ca. 80%. The versatility of microfluidics allowed incorporating hydrophilic metal-organic framework (MOF) ZIF-93 to produce HF modules with PA/MOF bilayered membranes (a continuous layer of MOF between the support and the PA film) which led to an important enhancement of the water permeance from 1.3 (bare PA membrane) to 5.3 L·m−2·h−1·bar−1 (PA/ZIF-93 HF membrane), maintaining RB rejection above 95%.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Organic solvent-free fabrication of thin film polyamide/zeolitic imidazolate framework membranes for removal of dyes from water

  • Luque-Alled, José Miguel
  • Martínez-Izquierdo, Lidia
  • Gorgojo, Patricia
  • Téllez, Carlos
  • Coronas, Joaquín
Thin film composite (TFC) polyamide (PA) membranes in combination with zeolitic imidazolate frameworks (ZIF), such as ZIF-8 and ZIF-93, have been fabricated using a novel approach based on vapor phase interfacial polymerization (VIP). These membranes have been investigated for nanofiltration (NF) of aqueous solutions of organic dyes, such as Rose Bengal (RB, 1017 Da), Sunset Yellow (SY, 452 Da) and Acridine Orange (AO, 265 Da). The preparation of the PA layer by VIP technique avoids the use of any organic solvent that is typically required in the conventional PA synthesis. Both ZIF-8 and ZIF-93 were initially synthesized using conventional procedures (methanol-based route) and incorporated to the PA layer in two different configurations: i) thin film nanocomposite with ZIF embedded within the PA film, and ii) bilayer membranes with a layer of ZIF between the support and the PA layer. The synthesis of ZIF-93 using a water-based route was developed for the bilayer configuration allowing for an organic solvent-free fabrication of PA/ZIF-93 bilayer VIP-TFC. These membranes showed the highest water permeances of 2.6, 3.4 and 2.2 L m-2h−1 bar−1 for RB, SY and AO, respectively. As compared to the control membrane VIP-TFC, this represents permeance increases of 69–117% and maintains high (greater than 99%) rejection of all the organic dyes. Membrane characterization demonstrated that the permeance enhancement for bilayer PA/ZIF-93 VIP-TFCs is related to an improved hydrophilicity, higher surface roughness and thinner selective layers. The prepared membranes demonstrated excellent cycle stability, maintaining their initial water permeance and dye rejection throughout 34 h of long-term operation, and being able to operate across the entire pH range studied (pH 3 to 9) without any detrimental effects on performance.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Lindane removal by membrane nanofiltration

  • Ruiz-Gutierrez, Adrián
  • Lasobras, Javier
  • Coronas, Joaquín
  • Menéndez, Miguel
  • Luque-Alled, José Miguel
Lindane is the γ-isomer of 1,2,3,4,5,6-hexachlorocyclohexane (HCH) and it has been widely used in the pesticide industry due to its insecticide properties. In the production of lindane, significant quantities of other HCH isomers are generated as byproducts. All these compounds are typically stored in landfills, often with poor management practices. Polyamide membranes, two commercial membranes from Alfa Laval (NF99HF and NF99) and homemade thin film composite membranes prepared by interfacial polymerization on a porous polyimide support, were evaluated for water nanofiltration (NF) of HCH isomers, including lindane. Homemade membranes, with a lindane rejection of 91.3 % and a permeance of 2.7 L·m−2·h−1·bar−1, offered the highest performance in terms of both permeance and rejection. NF99 and homemade membranes were proven to be equally effective in removing α-HCH and β-HCH, showing similar results. Homemade membranes achieved 99.5 and 99.8 % rejections for α-HCH and β-HCH, respectively. Long-term experiments were carried out with NF99 and homemade membranes to assess their stability during filtrations with lindane solutions for up to 214 h. Homemade TFC membrane maintained its initial rejection (ca. 93.5 %) after 214 h, although its permeance decreased over time, ending in 2.5 L·m−2·h−1·bar−1.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Sustainable ß- and ¿-cyclodextrins for development of highly permeable thin film composite nanofiltration membranes

  • Pina-Vidal, Cristina
  • Luque-Alled, Jose Miguel
  • Coronas, Joaquín
  • Téllez, Carlos
The use of macromolecules, such as cyclodextrins (CDs), given their porosity and compatibility with organic materials, are very attractive for the progress of polymeric membranes in nanofiltration (NF) of aqueous dye solutions. Two types of membranes were fabricated. Firstly, β- and γ-CDs were incorporated to polyamide (PA) thin film composite (TFC) membranes. These membranes, named CD/MPD-TMC, were prepared by conventional interfacial polymerization —i.e., an aqueous solution of m-phenylenediamine (MPD) followed by a solution of trimesoyl chloride (TMC) in hexane— by replacing a certain amount of the MPD monomer with varying proportions of CDs. Secondly, two-step double-IP (TD-IP) membranes were fabricated as follows: CDs were deposited atop the polymer support, followed by addition of TMC —forming a polyester (PE) layer—, and subsequently the membrane surface was modified with MPD molecules. In both CD/MPD-TMC and TD-IP membranes, the presence of CDs improved the membrane performance, the latter configuration leading to much higher water permeances. The TD-IP membrane using β-CD achieved the highest water permeance of 10 L m−2 h−1·bar−1 (LMH bar−1) and a rejection of acridine orange dye (265 Da) greater than 98 %. This represents a 6-fold increase in water permeance compared to bare PA (1.6 LMH bar−1). The enhanced water transport was mainly attributed to the more hydrophilic nature of the membranes and the presence of a PE layer with a porous structure and high pore connectivity. High dye rejection resulted from electrostatic and Donnan repulsions due to surface modification with MPD molecules.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Ultrasmall Functionalized UiO-66 Nanoparticle/Polymer Pebax 1657 Thin-Film Nanocomposite Membranes for Optimal CO2 Separation

  • Martínez-Izquierdo, Lidia
  • García-Comas, Cristina
  • Dai, Shan
  • Navarro, Marta
  • Tissot, Antoine
  • Serre, Christian
  • Téllez, Carlos
  • Coronas, Joaquín
Ultrasmall 4 to 6 nm nanoparticles of the metal–organic framework (MOF) UiO-66 (University of Oslo-66) were successfully prepared and embedded into the polymer Pebax 1657 to fabricate thin-film nanocomposite (TFN) membranes for CO2/N2 and CO2/CH4 separations. Furthermore, it has been demonstrated that ligand functionalization with amino (−NH2) and nitro (−NO2) groups significantly enhances the gas separation performance of the membranes. For CO2/N2 separation, 7.5 wt % UiO-66-NH2 nanoparticles provided a 53% improvement in CO2 permeance over the pristine membrane (from 181 to 277 GPU). Regarding the CO2/N2 selectivity, the membranes prepared with 5 wt % UiO-66-NO2 nanoparticles provided an increment of 17% over the membrane without the MOF (from 43.5 to 51.0). However, the CO2 permeance of this membrane dropped to 155 GPU. The addition of 10 wt % ZIF-94 particles with an average particle size of ∼45 nm into the 5 wt % UiO-66-NO2 membrane allowed to increase the CO2 permeance to 192 GPU while maintaining the CO2/N2 selectivity at ca. 51 due to the synergistic interaction between the MOFs and the polymer matrix provided by the hydrophilic nature of ZIF-94. In the case of CO2/CH4 separation, the 7.5 wt % UiO-66-NH2 membrane exhibited the best performance with an increase of the CO2 permeance from 201 to 245 GPU.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

PVDF hydrophobic hollow fiber membrane modules for partial dealcoholization of red wine by osmotic distillation as a strategy to minimize the loss of aromas

  • Esteras-Saz, Javier
  • Iglesia, Óscar de la
  • Marechal, Willian
  • Lorain, Olivier
  • Peña, Cristina
  • Escudero, Ana
  • Téllez, Carlos
  • Coronas, Joaquín
Tempranillo red wines were partially dealcoholized (−3 v/v%) by osmotic distillation (OD) with membranes. First, polypropylene (PP) Liqui-Cel3M (3M) hollow fiber membrane modules were applied at 11 and 15 °C to study the effect of the removal of ethanol on the aroma of a certain wine. The influence of both temperatures was evaluated in terms of ethanol flux and aroma losses. Afterwards, two additional wines with different compositions were dealcoholized. The impact of the initial concentration of aromas on achieving a final product with an appealing aroma profile was studied, displaying the three wines a comparable aroma retention. Membrane OD was carried out with two additional hollow fiber membrane modules: another PP module (Zena) with a higher pore size, and a superhydrophobic PVDF module (Polymem). The latter gave rise to a partial dealcoholized wine with an aroma profile very similar to that of the pristine wine.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Microwave-assisted synthesis of metal–organic frameworks UiO-66 and MOF-808 for enhanced CO2/CH4 separation in PIM-1 mixed matrix membranes

  • Yahia, Mohamed
  • Lozano, Luis A.
  • Zamaro, Juan M.
  • Téllez, Carlos
  • Coronas, Joaquín
This study presents a sustainable microwave-assisted synthesis, based on the use of acetone and a water/acetic acid mixture instead of typical harmful DMF, to fabricate Zr-metal–organic frameworks (MOFs) UiO-66 and MOF-808 as fillers in a PIM-1 matrix for gas separation application. The mixed matrix membranes (MMMs) were prepared with varying loadings (2.5–10 wt%) of MOFs. The physicochemical properties (1H NMR, FTIR, XRD, N2 adsorption, TGA and SEM) of the resulting PIM-1, MOFs and MMMs were analyzed. The CO2/CH4 separation performance and membrane aging characteristics of the MMMs were evaluated. The incorporation of MOF fillers significantly improved CO2 permeability and CO2/CH4 selectivity, attributed to their CO2-philicity and narrow pore size (UiO-66 ≈ 0.6 nm and MOF-808 ≈ 1.8 nm). The MMMs with higher filler loadings (7.5 and 10 wt%) exhibited the most favorable separation performance. Due to the better crystallinity and textural properties, MOF-808 produced the best separation results at 10 wt% filler loading (a CO2/CH4 separation selectivity of 16.2 at 9090 Barrer of CO2 permeability). Aging led to a decrease in CO2 permeability but a slight increase in CO2/CH4 selectivity for all MMMs. Overall, the study highlights the potential of PIM-1/UiO-66 and PIM-1/MOF-808 MMMs as efficient materials for (CO2/CH4) separation comparing with the pristine PIM-1.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Highly permeable ZIF-8 membranes for C2H4/C2H6 separation in a wide temperature range

  • Pérez Miana, Marta
  • Coronas, Joaquín
  • Hedlund, Jonas
  • Yu, Liang
Ethylene/ethane separation is a critical and energy-consuming process in the chemical industry due to the similar properties of the compounds and the great need of ethylene for e.g., polymer production. Many materials have been studied for their implementation as membranes as an energetically favorable alternative to conventional distillation and adsorption processes. Metal-organic frameworks (MOF) have revealed promising properties as highly permeable and selective membranes. Among the most studied and promising MOF candidates is ZIF-8, known for its thermal stability and small pores connected by narrow-sized windows. In this work, we present an analysis of the influence of parameters such as temperature, feed pressure and feed flowrate on the separation of ethylene/ethane through a thin ZIF-8/alumina disc membrane. We observed that the temperature has a significant effect on the separation. The ethylene permeance increased with decreased temperature and reached 8.1 × 10−7 mol/(m2·s·Pa) at −30 °C. At this temperature, the ethylene/ethane selectivity was 2.5. The study concluded with a considerable enhancement of the permeance of ZIF-8 membranes for ethylene/ethane separations, while maintaining a good selectivity compared to the reported values in the literature. The results have important implications for the development of more cost-effective and energy-efficient membrane-based separation technologies for ethylene purification.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Mechanochemical encapsulation of caffeine in UiO-66 and UiO-66-NH2 to obtain polymeric composites by extrusion with recycled polyamide 6 or polylactic acid biopolymer

  • Pina-Vidal, Cristina
  • Berned-Samatán, Víctor
  • Piera, Elena
  • Caballero, Miguel Ángel
  • Téllez, Carlos
The development of capsules with additives that can be added to polymers during extrusion processing can lead to advances in the manufacturing of textile fabrics with improved and durable properties. In this work, caffeine (CAF), which has anti-cellulite properties, has been encapsulated by liquid-assisted milling in zirconium-based metal–organic frameworks (MOFs) with different textural properties and chemical functionalization: commercial UiO-66, UiO-66 synthesized without solvents, and UiO-66-NH2 synthesized in ethanol. The CAF@MOF capsules obtained through the grinding procedure have been added during the extrusion process to recycled polyamide 6 (PA6) and to a biopolymer based on polylactic acid (PLA) to obtain a load of approximately 2.5 wt% of caffeine. The materials have been characterized by various techniques (XRD, NMR, TGA, FTIR, nitrogen sorption, UV–vis, SEM, and TEM) that confirm the caffeine encapsulation, the preservation of caffeine during the extrusion process, and the good contact between the polymer and the MOF. Studies of the capsules and PA6 polymer+capsules composites have shown that release is slower when caffeine is encapsulated than when it is free, and the textural properties of UiO-66 influence the release more prominently than the NH2 group. However, an interaction is established between the biopolymer PLA and caffeine that delays the release of the additive.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

ZIF-8 modified with 2-undecylimidazolate as filler for mixed matrix membranes for CO<sub>2</sub> separation

  • Pérez-Miana, Marta
  • Luque-Alled, José Miguel
  • Yahia, Mohamed
  • Mayoral, Álvaro
  • Coronas, Joaquín
A novel modification of zeolitic imidazolate framework-8 (ZIF-8) with 2-undecylimidazolate (umIm) was explored to enhance its hydrophobic character and improve its compatibility with polymer of intrinsic microporosity PIM-1 when incorporated as a filler in mixed matrix membranes (MMMs). In addition to the study of the best conditions to exchange the structural ligand of ZIF-8 by umIm and the characterization (by FTIR, RMN, XRD, TGA, N2 adsorption and TEM) of the obtained material, comparative analyses were conducted using MMMs containing the original ZIF-8 and the modified version. Different loadings were applied to study the impact on gas separation properties. Remarkably, the MMM with the modified ZIF-8 demonstrated superior performance surpassing the Robeson upper bound line of 2008 and revealing the effectiveness of this MOF modification strategy. In fact, with the 10 wt% ZIF-8-umIm loading MMM, the highest value of CO2/N2 selectivity was 15.4 (12% higher than that of bare PIM-1) at a CO2 permeability of 16 667 Barrer (52% higher than that of bare PIM-1). These findings highlight the promising potential of the ZIF-8 modification with umIm as a valuable filler material for MMMs in gas separation applications.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Sustainable low-alcohol beer production by combination of membrane osmotic distillation and pervaporation

  • Esteras-Saz, Javier
  • Maach, Amina
  • De la Iglesia, Óscar
  • Fumanal, Antonio J.
  • Kumakiri, Izumi
  • Téllez, Carlos
  • Coronas, Joaquín
Membrane osmotic distillation (OD) is applied in this work for the partial dealcoholization of beer (5.2 v/v% alcohol content) to diminish its ethanol content by around 50% giving rise to a low alcohol beer. A compromise is sought between the low alcoholic degree achieved and beer sensory properties. Moreover, the feasibility of the membrane OD process intensification is studied thanks to its combination with membrane pervaporation (PV). Two successive PV stages, one hydrophobic and the other hydrophilic, allow the production of recycled water (with less than 0.5 wt% ethanol) for the membrane OD operation and bioethanol (99% ethanol) as valuable byproduct.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Open and FAIR data for nanofiltration in organic media: A unified approach

  • Van Buggenhout, Simon
  • Ignacz, Gergo
  • Caspers, Scout
  • Dhondt, Robin
  • Lenaerts, Marie
  • Lenaerts, Nathalie
  • Hosseinabadi, Sareh Rezaei
  • Nulens, Ines
  • Koeckelberghs, Guy
  • Ren, Yi
  • Lively, Ryan P.
  • Rabiller-Baudry, Murielle
  • Lim, Ki Min
  • Ghazali, Nazlee
  • Coronas, Joaquin
  • Abel, Milan
  • Wessling, Matthias
  • Skiborowski, Mirko
  • Oxley, Adam
  • Han, Seok Ju
  • Livingston, Andrew
  • Yi, Zhuan
  • Gao, Congjie
  • Guan, Kecheng
  • Gonzales, Ralph Rolly
  • Matsuyama, Hideto
  • Bettahalli, Srivatsa NM.
  • McCutcheon, Jeffrey R.
  • Radmanesh, Farzaneh
  • Benes, Nieck E.
  • Tashvigh, Akbar Asadi
  • Fang, Qing
  • Zhang, Kaisong
  • Chen, Guining
  • Jin, Wanqin
  • Zhang, Yatao
  • Zhang, Chun-Xu
  • Liu, Mei-Ling
  • Sun, Shi-Peng
  • Buekenhoudt, Anita
  • Zhao, Chen
  • Bruggen, Bart Van der
  • Kim, Jeong F.
  • Condes, Lucas C.
  • Webb, Matthew T.
  • Galizia, Michele
  • Alhazmi, Banan
  • Upadhyaya, Lakshmeesha
  • Nunes, Suzana P.
  • Kim, Dae Woo
  • Schröter, Henrik
  • Kragl, Udo
  • Störtte, Sven
  • Vorholt, Andreas J.
  • Culfaz-Emecen, P. Zeynep
  • Pizzoccaro-Zilamy, Marie-Alix
  • Winnubst, Louis
  • Yushkin, Alexey
  • Volkov, Alexey
  • Chau, John
  • Sirkar, Kamalesh K.
  • Lu, Shao
  • Szekely, Gyorgy
  • Vankelecom, Ivo
  • Verbeke, Rhea
Organic solvent nanofiltration (OSN), also called solvent-resistant nanofiltration (SRNF), has emerged as a promising technology for the removal of impurities, recovery of solutes, and the regeneration of solvents in various industries, such as the pharmaceutical and the (petro)chemical industries. Despite the widespread use of OSN/SRNF, the presence of scattered, non-standardized data, and the absence of openly accessible data pose critical challenges to the development of new membrane materials and processes, their comparison to the state-of-the-art materials, and their fundamental understanding. To overcome these hurdles, data from peer-reviewed research articles and commercial datasheets were curated via a standardized procedure to obtain an extensive dataset on the membrane materials, synthesis parameters, operational conditions, physicochemical properties, and performance of OSN/SRNF membranes. Thanks to a truly impressive joint effort of the OSN/SRNF community, the dataset contains, as per April 2024, 5006 unique membrane filtrations from 294 publications for 42 solvents under several process parameters. This findable, accessible, interoperable, reproducible, and open (FAIR/O) dataset is available on both the OSN Database and the newly inaugurated Open Membrane Database for SRNF (OMD4SRNF). These databases provide multiple visualization and data exploration tools. Here, the standardized procedure applied to curate the data and the functionality of the databases are outlined, as well as the online user interface to deposit new data by external users on the OMD4SRNF. This community-led project has been supported by all the co-authors of this work. Most importantly, they additionally agreed to systematically deposit their future peer-reviewed data on OSN/SRNF into the databases. We thereby pave the road for FAIR/O data in the field of OSN/SRNF to increase transparency, enable more accurate data analysis, and foster collaboration and innovation.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Thin film nanocomposite membranes based on renewable polymer Pebax® and zeolitic imidazolate frameworks for CO2/CH4 separation

  • Refaat, Dalia
  • Yahia, Mohamed
  • Coronas, Joaquín
This study investigates the impact of integrating Pebax® Rnew® 30R51, a sustainable elastomer-type copolymer material, with zeolitic imidazolate frameworks (ZIFs) to develop advanced membranes for CO2/CH4 gas separation. The fabrication process of ZIF/Pebax® Rnew® 30R51 thin films was optimized to achieve uniform and defect-free thin film composite (TFC) membranes. Crucial membrane properties, including permeability, selectivity and separation efficiency, were analyzed with variations in ZIF type, loading levels, film thickness and operating conditions. Additionally, the resulting TFC and ZIF/Pebax® Rnew® 30R51 thin film nanocomposite (TFN) membranes were subjected to characterization via FTIR, XRD, TGA and SEM to evaluate their physicochemical properties. Nanoparticles of ZIF-8, NH2-ZIF-8 and ZIF-94 were individually added (at 5–15 wt% loadings) to the Pebax® Rnew® 30R51 matrix to develop the CO2 separation efficiency. The pristine TFC membrane showed a 66 GPU CO2 permeance and a 37.5 CO2/CH4 separation selectivity, primarily due to improved CO2 mass transport. Upon inclusion of ZIFs, the CO2 permeance with 5 wt% loadings of ZIF-8, NH2-ZIF-8 and ZIF-94 increased to 148, 99 and 125 GPU, respectively, despite this, the CO2/CH4 separation selectivity maintained at 29.4, 37.0 and 27.0, respectively.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Enhancing CO2/CH4 separation performance in PIM-1 based MXene nanosheets mixed matrix membranes

  • Yahia, Mohamed
  • Refaat, Dalia
  • Coronas, Joaquín
  • Téllez, Carlos
This study presents an approach by integrating MXene nanosheets (Ti2C3Tx) into polymer of intrinsic microporosity (PIM-1) matrix to develop mixed matrix membranes (MMMs) for biogas upgrading. Different concentrations (1–5 wt%) of MXene were incorporated into PIM-1, and the resulting materials were characterized to 1H NMR, FTIR, XRD, TGA, nitrogen adsorption, SEM and EDS to assess their physicochemical properties. The research focused on evaluating the gas separation performance, particularly CO2/CH4 separation, as well as the aging behavior of the MMMs. The incorporating of MXene nanosheets significantly enhanced the CO2 permeability and selectivity of PIM-1 by enhancing gas solubility and diffusivity. The most promising results were observed at 5 wt% filler loading, achieving a 13.5 CO2/CH4 separation selectivity at 7652 Barrer of CO2 permeability. In all membranes with aging time (60 days), there was a decrease in CO2 permeability and a slight increase in CO2/CH4 selectivity, observing that the introduction of MXene slightly mitigates the physical aging process in the PIM-1 polymer. Additionally, the permeability tests revealed higher CO2 permeability and (CO2/CH4) selectivity values for mixed gases compared to single gases. Overall, the study highlights the potential of MXene/PIM-1 MMMs as effective materials for CO2/CH4 separation, outperforming pristine PIM-1.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Microwave synthesis of UiO-66 with encapsulated caffeine: Liquor mother reuse and release from polyamide composites

  • Pina-Vidal, Cristina
  • Ortega-Moreno, Gabriela A.
  • Lozano, Luis A.
  • Piera, Elena
  • Caballero, Miguel A.
  • Zamaro, Juan M.
  • Téllez, Carlos
In this study, UiO-66 was in-situ synthesized with encapsulated caffeine (CAF@UiO-66) following a one-pot DMF-free microwave-assisted method. The microwave-assisted approach allowed for an efficient and fast encapsulation of caffeine within the metal-organic framework in a single step thus achieving a more environmentally friendly process. It was shown that the CAF@UiO-66 solid was capable of gradually dosing caffeine into aqueous media over a long period. Moreover, the recovered synthesis solution containing residual caffeine and solvent was successfully reused in several encapsulation cycles, giving capsules that showed good caffeine release properties. In addition, CAF@UiO-66 solids were incorporated into polyamide 6 (PA6) fibers through an extrusion process without altering their physicochemical properties. These composites showed a gradual and sustained release of caffeine, extending the dosage time and shelf life of the additive which made it potentially useful for its application in functional textile products. Finally, the release of caffeine from the capsules was fitted to a Fickian model while that from the polymeric composites was adjusted to the semi-empirical Korsmeyer-Peppas model.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Andrographolide Encapsulation in Metal-Organic Frameworks (MOFs) via Solvent-Free Process at High Pressure

  • Pantoja-Romero, Wenndy
  • Aysa-Martínez, Yolanda
  • Lavín-Flores, Alexis
  • Medina-Berrios, Nataniel
  • Bayro, Marvin J.
  • Morell, Gerardo
  • Weiner, Brad R.
  • Coronas, Joaquín
Andrographolide (ADG) encapsulation was carried out on MOFs MIL‐53(Al) and ZIF‐8 by high‐pressure (0.3 GPa) contact. This methodology is not only environment‐friendly but also energy/time‐saving and gives rise to ADG‐MOFs with physical features equivalent to those of materials obtained by common liquid phase encapsulation. The loaded MOFs were characterized through TEM, SEM, XRD, TGA, FT‐IR, BET, and NMR. The observed decrease in the intensity of ADG XRD peaks is due to the adsorption of ADG into the MOFs. TGA showed the decomposition step of ADG in the range of 200–300 °C in both loaded MOFs. FT‐IR also showed intense signals of the ADG in the synthesized materials. The dissolution profile of ADG in MIL‐53(Al) in PBS (pH=7.4) was carried out showing that the drug was released up to 96 % after 75 h. Solid‐state NMR confirmed the interactions between ADG molecules and ZIF‐8 groups and the formation of a hydrogen bond between the carboxylic group of ADG and the hydroxyl group of MIL‐53(Al). Coefficient partition studies determined that both MOFs did not improve the hydrophilicity of the ADG, due to the loading of the drug preferably occurring by interactions in the hydrophobic areas within the pores of the MOFs.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

How Can the Filler-Polymer Interaction in Mixed Matrix Membranes Be Enhanced?

  • Hasan, Md. Rafiul
  • Coronas, Joaquín
Mixed matrix membranes (MMMs) constitute a type of molecular separation membranes in which a nanomaterial type filler is dispersed in a given polymer to enhance its selective permeation ability. The key issue in MMMs is the establishing of a proper filler‐polymer interaction to avoid non‐selective transport paths while increasing permeability but also to improve other membrane properties such as aging and plasticization. Along the pass years several strategies have been applied to enhance the physicochemical interaction between the fillers (e. g. silicas, zeolites, porous coordination polymers, carbonaceous materials, etc.) and the membrane polymers: increase of external surface area, priming, use of intrinsically more compatible fillers, in situ synthesis of filler, in situ polymerization, polymer side‐chain modification and post‐synthetic modification of filler.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Improvement of the flame retardancy of polyamide 6 by the incorporation of UiO-66 and UiO-66/melamine

  • Pina-Vidal, Cristina
  • Berned-Samatán, Víctor
  • Piera, Elena
  • Caballero, Miguel A.
  • Téllez, Carlos
The flame retardancy of polyamide 6 (PA6) has been investigated through the incorporation of the metal–organic framework (MOF) UiO-66 and a composite of UiO-66/melamine during the extrusion process. The prepared materials have been characterised by various techniques: XRD, XPS, FTIR, TGA, DSC, SEM, EDX and mechanical properties. Moreover, to examine the efficiency of the flame retardants, the composites have been tested using the UL-94 vertical and, horizontal burning test, as well as the limiting oxygen index (LOI). The UL-94 V-2 standard has been achieved with only a 4 wt% load of either UiO-66 or UiO-66/melamine, compared to pure polyamide, which is not classified. The best results have been achieved with the UiO-66/melamine sample at 7 wt%, which prevents the agglomeration of UiO-66 alone. The highest LOI value was also obtained with this sample, achieving a value of 35.5 %, compared to pure PA6 and with UiO-66, which reached values of 22.4 % and 23.2 %, respectively. A flame suppression mechanism of the UiO-66/melamine composite is proposed, based on the formation of zirconium oxide, gas adsorption by the MOF and release of NH3.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Influence of the delamination of zeolitic imidazolate framework ZIF-7-III on the conversion of sucrose into methyl lactate

  • Navarro, Marta
  • Iglesia, Óscar de la
  • Téllez, Carlos
  • Coronas, Joaquín
The catalytic conversion of sugars to methyl lactate has been in the spotlight of the scientific community in the last decades. In this context, delaminated materials can provide better catalytic performances than their precursors, since they have a better accessibility to their active sites. In order to improve the yield to methyl lactate (ML), new delaminated material ZIF-7-III_EX was synthesized from the exfoliation of the dense Zn-based zeolitic imidazolate framework ZIF-7-III. Different techniques, namely XRD, SEM, TEM, thermogravimetric analysis and CO2 adsorption, were carried out to characterize the obtained materials as well as to verify the exfoliation of the precursor. Regarding the catalytic results, as-synthesized ZIF-7 showed a promising yield to ML, 41.2 %, superior to that achieved by ZIF-9 (based on Co instead of Zn). In addition, the delaminated material ZIF-7-III_EX reached a ML yield of 69.1 %, which implies 67.7 % and 97.4 % of improvements with respect to ZIF-7 and to ZIF-7-III, respectively. The reuse of some selected catalyst materials derived from ZIF-7-III was also studied.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Metal-organic frameworks/graphene oxide nanohybrids to control pore wetting in membrane distillation

  • Moriones, Andoni
  • Cano-Herranz, Lucía
  • Luque-Alled, Jose Miguel
  • Téllez, Carlos
  • Gorgojo, Patricia
Membrane distillation (MD) is an emerging technology in the field of water desalination due to its high-energy efficiency and the fact that is not affected by feed salt concentration. As an alternative to feed water pre-treatment, membrane surface modification aims at changing different properties to make it less prone to fouling. This work addresses the mitigation of the most concerning membrane degradation effects in MD, such as pore wetting and fouling, by modifying the membrane surface. This work takes advantage of the adsorption properties of metal-organic frameworks (MOF)@graphene oxide (GO) nanohybrids to create sacrificial sites (located zones where adsorption of foulants is facilitated) on the membrane surface. MOF@GO nanohybrids are embedded between two polydopamine (PDA) layers that are deposited on top of commercial polyethylene (PE) membranes. Two types of MOF@GO nanohybrids were evaluated, one containing UiO-66-NH2 and the other one ZIF-8. Air gap membrane distillation (AGMD) experiments using highly concentrated foulant solutions to accelerate the effects of membrane degradation, showed that surface modification effectively extended membrane life. The selective foulant adsorption delayed pore wetting and allowed to retain most of the membrane flux. Pore wetting occurred after 109 h for the membrane containing ZIF-8@GO (500 mg·m−2), compared to 4–5 h for the unmodified commercial membrane. Due to their high adsorption properties, the presence of MOFs is essential to ensure the formation of sacrificial sites and to maintain the initial flux, thus higher fluxes were observed for MOF@GO membranes (13 kg·m−2·h−1), compared to those containing only GO (5 kg·m−2·h−1).
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Study for CO2 separation with poly(ethylene oxide terephthalate)-poly(butylene terephthalate) multiblock copolymer membranes: Approaching a greener solvent preparation

  • Martínez-Visus, Íñigo
  • Téllez, Carlos
  • Coronas, Joaquín
Green solvent alternatives for the multiblock copolymer PolyActive™ were selected to test their effectiveness in membrane fabrication for gas separation. Solubility tests were conducted to assess the solvent-polymer compatibility, followed by membrane fabrication using a drop casting-solution method. Ethyl lactate was identified as a potential greener solvent, compared to more commonly used solvents like chloroform and tetrahydrofuran, as it maintained the membrane conformation, thermal and chemical stability, and thermal degradation characteristics as demonstrated by membrane characterization using SEM, FTIR, TGA and DSC. Single gas transport parameters (permeability, diffusivity and solubility) for N2, H2, CH4, He and CO2 were obtained via the time-lag method for the prepared membranes. A temperature dependence study was conducted in the 25–70 °C range, calculating activation energies for gas transport properties and ideal selectivities. Mixed gas measurements were also performed, comparing separation selectivities to those (ideal selectivities) obtained in single gas, indicating a potential competitive adsorption effect between less permeable species, leading to more selective separation in gas mixture. Membranes prepared with different polymer concentrations (1, 2 and 5 wt%) in ethyl lactate achieve a CO2/N2 ideal selectivity of up to 50.4 at a CO2 permeability of 179 Barrer. This enhanced performance was attributed to ethyl lactate higher boiling point, resulting in a more densely packed polymer structure as reflected by the higher crystallinity and lower fractional free volume measured through XRD, DSC and pycnometry analyses.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Amphiphilic Zeolitic Imidazolate Framework for Improved CO2 Separation in PIM-1 Mixed Matrix Membranes

  • Pérez-Miana, Marta
  • Luque-Alled, José Miguel
  • Mayoral, Álvaro
  • Martínez-Visus, Íñigo
  • Foster, Andrew B.
  • Budd, Peter M.
  • Coronas, Joaquín
This study aims to enhance the compatibility between filler and polymer in mixed matrix membranes (MMMs), addressing an important challenge in membrane development. ZIF‐94, known for its affinity to CO2, was partially modified with 2‐undecylimidazolate (umIm) through the solvent‐assisted ligand exchange (SALE) method to improve its compatibility with the prototypical polymer of intrinsic microporosity PIM‐1. The modified ZIF‐94 (ZIF‐94‐umIm) can be considered as an amphiphilic MOF with both hydrophilic and hydrophobic moieties, while maintaining a considerably high CO2 adsorption capacity (2.34 mmol g−1 at 90 kPa and 0 °C). Gas separation experiments were performed using mixed gas compositions of 15/85 CO2/N2 at 3 bar and 35 °C. The resulting MMM with a 5 wt.% loading exhibited an enhanced CO2 separation performance, with ca. 70% and 10% increases in CO2 permeability (8900 Barrer) and CO2/N2 selectivity (20.2), respectively, compared to pristine PIM‐1 membranes. In addition, thin film nanocomposite membranes were prepared showing a 23.5 CO2/N2 selectivity at 2350 GPU of CO2. This modification strategy shows a great potential for improving the CO2 capture technologies, highlighting the potential of tailoring MOF fillers for advanced membrane materials in gas separation applications.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Solvent-Free Process for Preparing Metal-Organic Framework Composites Based on Carbon-Based Quantum Dots and Their Derivatives as Drug Delivery Systems for Andrographolide

  • Pantoja-Romero, Wenndy
  • Lavín-Flores, Alexis
  • Morell, Gerardo
  • Martínez-Ferrer, Magaly
  • Weiner, Brad R.
  • Coronas, Joaquín
Andrographolide (ADG) was conjugated with MIL-53(Al), ZIF-8, carbon-based quantum dots (CBQDs) and doped carbon-based quantum dots (D-CBQDs) using high-pressure (0.3 GPa) contact. This solvent-free approach is environmentally friendly, energy-efficient, and time-saving, resulting in ADG-MOFs-CBQDs/D-CBQDs with physical properties comparable to those produced by traditional liquid phase encapsulation. The resulting nanocomposites were characterized using SEM, XRD, TGA, FT-IR, and 1H NMR. The results indicate that ADG was partly encapsulated within the metal-organic framework (MOF) pores, while another portion was bound externally to CBQD/D-CBQDs, as evidenced by distinct drug signals in each analysis. This green synthesis approach simplifies the conjugation process. It significantly enhances the drug solubility, as indicated by changes in hydrophobicity observed via 1H NMR, surpassing the improvements achieved by ADG encapsulation within MOFs alone. Additionally, in preliminary tests, the materials exhibited significant cytotoxicity against PC3 cells compared to ADG (25.05 ± 0.06 µg/mL) after 48 hours of exposure.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Zeolite@Metal-organic framework core-shell synthesized from the aluminum of the zeolite with accessible internal surface for CO2 adsorption

  • Güemes, Lucas
  • Navarro, Marta
  • Cacho-Bailo, Fernando
  • Jaimes-Paez, Cristian D.
  • Cazorla-Amorós, Diego
  • Téllez, Carlos
  • Coronas, Joaquín
Combining the rigid microporosity of zeolites with the more versatile structures of metal–organic frameworks (MOFs) seeks to obtain a synergistic effect of both materials. Starting from a low cost and industrially produced zeolite, as it is zeolite NaA (with the LTA type structure), we show that it is possible to crystallize a MOF as shell onto it by only using an aqueous solution of terephthalic acid (H2BDC). Unlike other zeolite-MOF hybrids reported in the literature, the crystallized MOF only uses the aluminum from the zeolite and may share in turn some aluminum atoms with the inorganic zeolite core, therefore it consists solely of zeolitic Al and BDC. Depending on the pretreatment of the zeolite and the synthesis conditions (pH, time, linker ratio), the crystalline zeolite core is maintained or converted into an amorphous aluminosilicate. Thus, it is possible to retain a part of the adsorption properties of the parent zeolite without degrading its structure. The resulting core–shell material, designated as LTA@Al-BDC, combines the zeolite microporosity and molecular sieving properties with the MOF that crystallizes as high aspect ratio sheets which, together with its hydrophobicity, favors the contact with polymeric materials. In addition, being zeolite 4A (NaA) affinity towards CO2 been probed, the resulting LTA@Al-BDC material constitutes a prominent candidate towards CO2 separation.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Enhanced flux of nanofiltration membranes for low molecular weight solutes using Zr-MOF@MoS2 nanohybrids as both interlayer and filler materials

  • Colás Sebastián, Javier
  • Luque-Alled, José Miguel
  • Téllez, Carlos
  • Coronas, Joaquín
This study investigates the fabrication and performance of polyamide (PA) thin film composite (TFC) membranes for nanofiltration applications, incorporating nanosized (∼10 nm) zirconium-based metal-organic frameworks (MOFs) and MoS2. Three different Zr-MOFs, namely UiO-66, UiO-66-NH2 and MOF-808, were synthesized and anchored onto 2D MoS2 nanosheets forming MOF@MoS2 nanohybrids. These nanohybrids were integrated into PA TFC membranes using two distinct methods: (i) embedding them into the PA layer, resulting in thin film nanocomposite (TFN) membranes, and (ii) creating bilayered membranes with the nanohybrids beneath the PA layer. The membranes were evaluated for the removal of organic dyes, such as Rose Bengal (RB, 1017 Da), Sunset Yellow (SY, 452 Da) and Acridine Orange (AO, 265 Da), from water. The TFN membranes containing UiO-66@MoS2 nanohybrids exhibited the highest performance, with a water permeance of 12 L·m−2·h−1·bar−1 for the SY dye solution, representing a 140 % increase relative to the control PA TFC membrane. All membranes exhibited high rejection values (> 98 %), with performance strongly influenced by the dye size and charge. The characterization revealed that the porosity and sorption capacities of the nanohybrids are crucial to obtain more permeable membranes, but other factors such as negative surface charge, roughness and hydrophilicity play an important role.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Membrane preparation assisted by integration of machine learning and response surface methodology for CO2 separation

  • Carrillo-Sánchez, Lucía
  • Téllez, Carlos
  • Coronas, Joaquín
The separation of carbon dioxide (CO2) is presented as a current challenge in the environment and energy sector. The primary reason for this is to control the emissions of this gas into the atmosphere and the upgrading of biomethane. In this context, the membrane separation technology seems to be a very sustainable promising tool for such tasks. This work presents a machine learning (ML) study, based on a database created from membrane preparation conditions and gas separation records from the literature, achieved for the CO2/N2 and CO2/CH4 mixtures using dense membranes of thermoplastic elastomer Pebax® 1657. A comparative analysis of three different ML models was carried out: multiple linear regression, decision tree and random forest. This last algorithm demonstrates the best performance in statistics terms of coefficient of determination and root mean square error. In addition, the combination of the ML random forest with a method based on the design of experiments with response surface methodology (RSM) allowed to identify the favorable conditions for the membrane synthesis, with the objective of enhancing the CO2 separation performance. This resulted in prepared membranes in the laboratory considering the proposed conditions by RSM with CO2 permeability and CO2/X selectivity values of 115 Barrer and 43.5 and 132 Barrer and 16.4 for the CO2/N2 and CO2/CH4 mixtures, respectively, at 35 °C.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Innovative starch-PVA membranes incorporating amino-functionalized Zeolitic Imidazolate frameworks for CO2/CH4 separation

  • Refaat, Dalia
  • Amenakpor, Jacking
  • Coronas, Joaquín
  • Zornoza, Beatriz
The growing need for efficient CO2 separation in natural gas purification and carbon capture has driven the advancement of high-performance membrane technologies. This study incorporates the zeolitic imidazolate framework ZIF-8-NH2 into blends of polysaccharide starch and polyvinyl alcohol (PVA) to fabricate eco-friendly membranes. These materials, prepared as dense mixed matrix membranes (MMMs) and thin-film nanocomposite (TFN) membranes, offer a sustainable solution for CO2/CH4 separation. The integration of ZIF-8-NH2 nanoparticles, recognized for their high crystallinity and surface area and selective adsorption capacity into the starch–PVA matrix (33/67 blend ratio), significantly enhances CO2 permeability, increasing from 124 to 188 Barrer at 10 wt% loading, while preserving high CO2/CH4 selectivity (14.1 for the pristine blend and 16.5 for the MMM). For TFNs, a 9/91 starch-PVA matrix with 15 wt% ZIF-8-NH2 incorporated into the selective layer resulted in the best conditions. This architecture provided robust mechanical stability and high separation performance, yielding a CO2 permeance of up to 208 GPU and a CO2/CH4 selectivity of 26.9 at 3 bar feed pressure, nearly doubling the selectivity compared to the dense biopolymer blend. This work highlights the potential of renewable, starch-based materials in membrane-based gas separation, contributing to sustainable solutions for natural gas purification and carbon capture.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Synergy of Block and Microporous Polymers with Tailored Zeolitic Imidazole Frameworks for Membrane-Based Direct Air Capture

  • Martínez-Visus, Íñigo
  • Carrillo-Sánchez, Lucía
  • Luque-Alled, José Miguel
  • Foster, Andrew B.
  • Budd, Peter M.
  • Téllez, Carlos
  • Coronas, Joaquín
Direct air capture (DAC) concerns the separation from air of carbon dioxide (CO2), the most significant greenhouse gas in the atmosphere, as a means of producing negative emissions. The challenge for the scientific and industrial communities is tremendous, and membrane technology is postulated as an efficient alternative in terms of energy, costs, and ease of implementation. Two polymers, commercial elastomeric PolyActive and high‐performance polymer of intrinsic microporosity (PIM‐1), with complementary permeation‐selectivity features, to form both dense and thin film composite membranes, are studied to operate in the 500 ppm to 15% range of CO2 feed concentration and at 10–50 °C temperatures. A study on its synergistic pairing for a multistage DAC process is evaluated and to enhance the separation performance, the membranes are modified with zeolitic imizadolate frameworks (ZIF), capable of modification by solvent‐assisted ligand exchange (SALE). A sequential SALE process is designed using two different ligands, one hydrophilic and the other hydrophobic, to modify nanosized ZIF‐8 and produce a ZIF with tailored ligand composition. This is aimed at improving both the CO2 interaction and compatibility of MOF with the membrane polymer, achieving at 500 ppm a CO2 permeance of 1037 GPU with a CO2/N2 selectivity of 16.2.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Mixed matrix membranes of PIM-1 incorporating MOF-808 functionalized with amino acids for enhanced CO2/CH4 separation

  • Refaat, Dalia
  • Yahia, Mohamed
  • Martínez-Hernández, Harol David
  • Jiménez-Ruiz, Monica
  • Galván, Vanessa
  • Petrenko, Viktor
  • Fernández de Luis, Roberto
  • Coronas, Joaquín
This study investigates the enhancement of CO2/CH4 separation performance in mixed matrix membranes (MMMs) by incorporating amino acid-functionalized MOF-808 (MOF-808@AA; AA = Lys, Arg and Cys) into a polymer of intrinsic microporosity (PIM-1) matrix. MMMs containing 10 wt% MOF-808@AA were fabricated via solution casting. The structural and physicochemical properties of PIM-1, MOF-808@AA, and the resulting MMMs were characterized using 1H-NMR, FTIR, TGA, SEM, XRD, SAXS, N2/77 K and CO2/15 °C isotherms, and high-pressure CO2 adsorption. Collectively, the characterization results confirm the successful incorporation of MOF-808@AA into the PIM-1 membranes, with no detectable alteration of the nanostructure of the PIM-1 matrix. Gas separation measurements revealed a notable increase in both CO2 permeability and CO2/CH4 selectivity upon incorporation of MOF-808@AA fillers. Among the tested membranes, the PIM-1/MOF-808@Lys MMM functionalized with lysine exhibited the best performance, achieving a CO2 permeability of 14 354 ± 201 Barrer and a CO2/CH4 selectivity of 26.4 ± 1.8. Aging effects were also studied, showing a reduction in CO2 permeability accompanied by a slight increase in selectivity over time. In addition, the single and mixed gas experiments at elevated pressures (up to 6 bar) showed that CO2 permeability under mixed gas conditions was slightly higher than in single gas experiments, supporting the potential of these MMMs for application in realistic CO2/CH4 separation processes under practical operating conditions. Inelastic neutron scattering (INS) and density functional theory (DFT) calculations confirmed that CO2 molecules preferentially interact with the amino groups introduced by AA functionalization. DFT simulations further revealed that while CO2 and CH4 access similar adsorption sites, the interaction energy of CO2 with amino groups is approximately three times higher than that of CH4. These findings demonstrate that MOF-808@AA fillers can significantly enhance the CO2-philicity of PIM-1-based MMMs, offering a promising approach for efficient CO2/CH4 separation compared to pristine PIM-1 or unmodified PIM-1/MOF-808 composites.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

High Pressure-Based Synthesis of Nanoporous Metal–Organic Framework ZIF-93 Giving Rise to a Phase for Proton Conduction

  • Pérez-Miana, Marta
  • Fernández de Luis, Roberto
  • Fidalgo-Marijuan, Arkaitz
  • Li, Junyan
  • Mayoral, Álvaro
  • Coronas, Joaquín
This study aims to develop a green, solvent-free synthesis of ZIF-93 (ZIF stands for zeolitic imidazolate framework) and to explore the formation of different phases. We report the solvent-free synthesis of a previously unreported nanoporous ZIF phase, ZIF-93_HP (HP referring to “high-pressure”), from zinc oxide using a dual high-pressure (150 MPa) and thermal (110 °C) method. The influence of key synthesis parameters, such as the amount of NH4NO3 promotor and reaction steps, was systematically investigated to maximize the conversion of ZnO into the intermediate ZIF-93_HP, while, in parallel, preventing its further conversion into nanoporous ZIF-93 phase. The material was extensively characterized by X-ray diffraction, thermogravimetry, electron microscopy and N2 and CO2 adsorption, which revealed insights into the structure, morphology and nanoporosity of ZIF-93_HP. ZIF-93_HP, with empirical formula of Zn(C5N2OH5)2·1.2(NH4NO3)·(H2O), is related to the previously reported ZIF-93 (Zn(C5N2OH5)2). Water washing of this phase led to the transformation into ZIF-93 and a significant increase in the BET specific surface area (from 4 to 181 m2/g). In addition, the presence of NH4+ and NO3– ions into its structure makes ZIF-93_HP proton conductor at room temperature and moisture conditions (3.76 × 10–3 S/cm), a property that decreases with increasing temperature due to dehydration. The discovery of ZIF-93_HP highlights the potential of the high-pressure, solvent-free synthesis as a powerful tool for the exploration of different ZIFs and reticular materials that are inaccessible through traditional solvothermal methods. As crystallization under solvent-free conditions is often influenced by nonthermodynamic equilibrium, this approach holds a great potential for expanding the material landscape by enabling the discovery of different phases and structures with unique properties, such as the promising proton conductivity demonstrated here.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Gaining insight into the synthesis of nanosized pure zeolite NaA

  • Güemes, Lucas
  • Coronas, Joaquín
  • Téllez, Carlos
In zeolite synthesis, controlling and reducing the particle size is advantageous for different processes in which mass transfer occurs through surface active sites. In this work, the hydrothermal synthesis of zeolite NaA has been studied in detail seeking to control the size, morphology and crystal phase of the resulting zeolite particles. Adjusting the crystallization conditions and molar composition of a SiO2-Al2O3-TMA2O-Na2O-H2O system allows for the consistent production of zeolite NaA with a particle size down to 68 nm measured by TEM, using tetramethylammonium (TMA) as the organic structure directing agent (OSDA). Within the composition region in which the LTA zeolite crystallization is favored, syntheses at higher OSDA/Na+ and Si/Al atomic ratios produce smaller particles. Depending on the synthesis gel molar formulation, different morphologies and sizes of LTA crystals (in the ~68–760 nm range) with slightly distinct Si/Al atomic ratios (in the 1.1–2.3 range) can be achieved. The synthesized zeolites were characterized in detail by different techniques, and their textural properties were evaluated through CO2 and N2 adsorption and correlated with their composition.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Covalent Organic Framework (COF) based mixed matrix membranes as an alternative solution for gas separation

  • Alom, Jahangir
  • Rahman, Md Abdur
  • Hossein, Mehrafarin
  • Ban, Sagar
  • Martínez-Visus, Íñigo
  • Ahmed, Mohammed Boshir
  • Keskin, Seda
  • Téllez, Carlos
  • Zornoza, Beatriz
Gas separation plays an essential role in refineries and the chemical industry, with membrane-based technologies gaining prominence for their low cost, compact equipment with a space-saving design footprint, energy efficiency, ease of scale-up, and environmental benefits. Current research focuses on enhancing membrane performance in actual operating conditions by optimizing the equilibrium between selectivity and permeability to expand commercial and industrial applications. This balance between selectivity and permeability can be addressed by using mixed-matrix membranes (MMMs), which are formed by adding nanostructured fillers to the polymer to enhance its separation properties. In this scenario, covalent-organic frameworks (COFs) show considerable potential. COFs have generated significant interest in membrane separation owing to their stable organic structures, compatibility with polymers, and tailorable pore sizes and chemical functionalities. This review provides a systematic overview of COF-based MMMs for gas separation, distinguishing this work from previous reviews that broadly address other inorganic fillers incorporated into MMMs. The manuscript critically examines the physicochemical design principles and effective synthesis routes of COF fillers, their structure-performance relationships within polymer matrix, and, finally, their influence on gas transport behavior under practical operating conditions. Furthermore, a thorough examination of the challenges and opportunities of COF-based MMMs, along with recent advancements in the field, is conducted. The key benefits and drawbacks of using COFs with MOF as a double filler in MMM for gas separation are assessed with respect to permeability, selectivity, interfacial compatibility, and long-term stability. The review also provides recent advances in molecular modeling and machine-learning approaches for rational COF-based MMM design. Lastly, a summary of current research initiatives and potential future research directions is provided to accelerate the development of scalable and industrially viable COF-based MMMs.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Controlled synthesis of ZIF-8 nanoparticles in the 20-60 nm range

  • Selvin, Minu
  • Esteras-Saz, Javier
  • Coronas, Joaquín
The control of particle size of zeolitic imidazolate framework ZIF-8 is crucial due to the high impact of such parameter on the material properties, like crystallinity and surface area, with an important effect on emerging applications related to composite materials, molecular separations and encapsulation, among others. This study focuses on controlling the effect of several basic parameters to achieve different particle sizes below 100 nm with a narrow particle size distribution. Specifically, synthesis time, stirring speed, the addition of a deprotonator and its nature were systematically studied. As a result, ZIF-8 with average particle sizes of ca. 20 ± 4, 40 ± 6 and 60 ± 3 nm was successfully obtained. The different particle sizes were observed by SEM and compared with the corresponding crystallite size calculated from powder X-ray diffraction using different models. The strong correlation between both sizes validates the reliability of our different approaches to the synthesis of ZIF-8.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Determining Si/Al atomic ratios in particulate matter via quadrupole single-particle ICP-MS with combined unit-mass and bandpass resolution modes: a proof-of-concept study on Antarctic snow

  • Mataloni, Matilde
  • Bazo, Antonio
  • Bolea-Fernandez, Eduardo
  • Rua-Ibarz, Ana
  • Aramendía, Maite
  • Güemes, Lucas
  • Téllez, Carlos
  • Coronas, Joaquín
  • Grotti, Marco
  • Resano, Martín
Micrometer-scale mineral dust deposited in Antarctica represents a valuable archive for reconstructing atmospheric variability and for improving our understanding of dust-climate interactions. Among the various types of particle-specific information available, elemental ratios, such as the Si/Al atomic ratio, are especially useful as geochemical indicators of particle composition and provenance. However, the nature of these samples, characterized by coexisting particle populations and limited particle numbers, makes this determination particularly challenging. In this work, a novel quadrupole-based single-particle ICP-mass spectrometry (SP-ICP-QMS) approach to determine population-specific Si/Al atomic ratios containing chemically heterogeneous particle populations is presented. To overcome the sequential acquisition inherent to ICP-QMS instrumentation, Al and Si measurements at unit-mass resolution (m/z 27 and 28, respectively) were combined with bandpass acquisition centered at m/z 27 (2.47 ± 0.06 amu resolution at 10% peak height), enabling simultaneous collection of 27Al+ and 28Si + signals. This strategy was first used to identify the Al and Si distributions belonging to the same particle population and, consequently, to determine the corresponding atomic ratios in a suspension containing SiO2 microparticles (MPs) and two different types of synthesized zeolite MPs with different Si/Al atomic ratios. The reliability and accuracy of the method were confirmed by comparing the results with those obtained from individual Scanning Electron Microscopy with Energy Dispersive X-ray Spectroscopy (SEM-EDX) and SP-ICP-MS characterization of the zeolite samples. As a proof-of-concept, the analysis of an Antarctic snow sample demonstrated the potential of the developed method to provide population-specific information - Si/Al atomic ratios - essential for environmental assessments based on high-resolution short-term records.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Repurposing metal-responsive regulators: The FUR family as a regulatory hub for lifestyle adaptation and biofilm architecture in Anabaena sp. PCC 7120

  • Olivan-Muro, Irene
  • Esteras-Saz, Javier
  • Coronas, Joaquín
  • Sevilla, Emma
  • Fillat, María F.
Cyanobacterial biofilms play a crucial role in maintaining aquatic ecosystem stability. However, the regulatory mechanisms governing the transition from planktonic growth to a sessile state remain poorly characterized. This lifestyle shift entails extensive transcriptional reprogramming. In Anabaena sp. PCC 7120 the three Ferric Uptake Regulator (FUR) paralogs FurA, Zur and PerR play key roles in coordinating this process. Although these proteins are established regulators of metal and redox homeostasis, their contribution to orchestrating multicellular behaviour has yet to be defined. In this study, we combined computational, biochemical, and surface characterization approaches to evaluate the influence of FUR proteins on biofilm architecture and to map the FUR-mediated regulatory network underlying its development. Our results identified Zur as a major regulator of extracellular matrix formation, directly controlling genes involved in carbohydrate metabolism and trehalose biosynthesis (alr1718, alr0894), thereby promoting structural maturation and desiccation tolerance. In contrast, PerR functioned as a developmental gatekeeper, as its deregulation led to elongated cells with impaired septation associated with the misregulation of the septal-junction regulator sjdR and the fatty acid biosynthesis gene lpxC. FurA maintained cellular homeostasis by regulating α-trehalase (all0166), thereby influencing extracellular matrix turnover. Scanning electron microscopy analysis confirmed that FUR deregulation markedly altered biofilm architecture, whereas environmental stressors such as nitrogen deficiency activated compensatory pathways that partially bypassed these regulatory constraints. Together, these findings demonstrate that metal-responsive regulators are repurposed to integrate environmental signals into the control of prokaryotic multicellularity, positioning the FUR family as a central regulatory hub for lifestyle adaptation in Anabaena.