Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 25
Encontrada(s) 1 página(s)

Repositorio Institucional de la Universidad de Burgos (RIUBU)
Publicación Artículo científico (JournalArticle)

Bending tests on building beams containing electric arc furnace slag and alternative binders and manufactured with energy-saving placement techniques

  • Santamaría, Amaia
  • García Llona, Aratz
  • Revilla Cuesta, Víctor
  • Piñero Santiago, Ignacio
  • Ortega López, Vanesa
The environmental impact of the building sector is especially relevant during the construction phase. Both the materials and the construction methods that are currently in use must be reconsidered, in order to minimize the environmental impact of concrete-based structures. This research is therefore focused on achieving greener concrete-based building structures. In this context, the feasibility of careful use of materials for concrete manufacture and the use of construction techniques that can facilitate and reduce energy consumption during placement are both studied. To do so, twelve sample beams were prepared using eight different sustainable high-workability structural concretes. The aim was to maximize the use of the by-products that amounted to over 80% of the concrete mass, steelmaking slags, fly ash, and quarry waste, and to employ energy-saving concrete placement techniques. The beams underwent bending tests in which their mechanical behavior and their compliance with the specifications of the most relevant building codes were verified. The results pointed to the feasibility of increased sustainability in the field of building engineering through the suitable use of selected by-products and techniques., Spanish Ministry MCI, AEI, EU and ERDF [RTI2018-097079-B-C31; 10.13039/501100011033; FPU17/ 03374]; the Junta de Castilla y Le´on (Regional Government) and ERDF [UIC-231, BU119P17]; Youth Employment Initiative (JCyL) and ESF [UBU05B_1274]; the University of Burgos [grant number SUCONS, Y135.GI], UPV/EHU (PPGA20/26) and, finally, our thanks also go to the Basque Government research group IT1314-19 and likewise to CHRYSO and HORMOR for supplying the materials for research.
Repositorio Institucional de la Universidad de Burgos (RIUBU)
Publicación Artículo científico (JournalArticle)

Temporal flowability evolution of slag-based self-compacting concrete with recycled concrete aggregate

  • Revilla Cuesta, Víctor
  • Skaf Revenga, Marta
  • Santamaría, Amaia
  • Hernández Bagaces, Jorge J.
  • Ortega López, Vanesa
The addition of by-products, such as recycled concrete aggregate and ground granulated blast furnace slag, modify the in-fresh flowability of ordinary self-compacting concrete both initially and over time. A detailed study is presented in this paper of 18 mixtures (SF3 slump-flow class) containing 100% coarse recycled concrete aggregate, two types of cement (CEM I or CEM III/A, the latter with 45% ground granulated blast furnace slag), different contents of fine recycled concrete aggregate (0, 50, or 100%), and three different aggregate powders (ultra-fine limestone powder <0.063 mm, limestone fines 0/0.5 mm, and recycled concrete aggregate 0/0.5 mm). The temporal evolution of slump flow, viscosity, and passing ability, and the values of segregation resistance, air content, fresh and hardened density, and compressive strength were evaluated in all the mixtures. The addition of fine recycled concrete aggregate and CEM III/A improved initial slump flow and passing ability by 6%, due to their higher proportion of fines. Nevertheless, the temporal loss of flowability within 60 min was 5.8% lower when adding natural aggregate and CEM I. Viscosity and air content increased 26% on average following additions of fine recycled concrete aggregate, unlike with additions of ground granulated blast furnace slag. Flowability and strength increased with the addition of limestone fines 0/0.5 mm. According to multi-criteria analyses, the mixtures with CEM III/A, 50% fine recycled concrete aggregate, and limestone fines 0/0.5 mm showed an optimal balance between their flowability (SF2 slump-flow class 60 min after the mixing process), compressive strengths (around 60 MPa), and carbon footprints., Spanish Ministry MCIU, AEI and ERDF [grant numbers FPU17/03374 and RTI 2018-097079-B-C31]; the Junta de Castilla y León (Regional Government) and ERDF [grant number UIC-231, BU119P17]; the Youth Employment Initiative (JCyL) and ESF [grant number UBU05B_1274]; the University of Burgos [grant number SUCONS, Y135. GI], UPV/EHU (PPGA20/26) and, finally, our thanks also to the Basque Government research group IT1314-19.
Repositorio Institucional de la Universidad de Burgos (RIUBU)
Publicación Artículo científico (JournalArticle)

Multi-criteria feasibility of real use of self-compacting concrete with sustainable aggregate, binder and powder

  • Revilla Cuesta, Víctor
  • Skaf Revenga, Marta
  • Espinosa González, Ana Belén
  • Ortega López, Vanesa
Replacing natural raw materials with industrial by-products can increase the sustainability of Self-Compacting Concrete (SCC), although its fresh and hardened behavior will usually worsen. The benefits of increased sustainability must therefore outweigh any reduction in concrete flowability and strength. These aspects can be analyzed through Multi-Criteria Decision-Making (MCDM) algorithms. In all, 19 SCC mixes were studied. One reproduced commercial SCC (limestone filler and conventional cement), the others were produced with more sustainable materials: 100% coarse Recycled Concrete Aggregate (RCA); 0%, 50% or 100% fine RCA; 45% Ground Granulated Blast-furnace Slag (GGBS); and sustainable aggregate powders such as limestone fines 0/0.5 mm and RCA powder 0/0.5 mm. Decreased flowability at 15 and at 60 min, compressive strength, modulus of elasticity, carbon footprint, and cost of mix were all studied. Both the carbon footprint and the cost were calculated considering only the composition of the SCC, without including aspects that depend on each particular case study, such as transport distances. These aspects constituted the decision-making criteria of the MCDM analysis, under which 14 scenarios were evaluated with different requirements for SCC, using 3 different algorithms (TOPSIS, AHP, and PROMETHEE). The results suggested that the ideal choice for fast concreting is a combination of GGBS, 100% coarse RCA and limestone fines, although if SCC has to be transported to the concreting point, then conventional cement should be used. Strength and stiffness can be maximized by limiting the fine RCA content to 50%. Finally, considering a versatile choice, only SCC with coarse RCA, limestone fines, GGBS and 0% fine RCA could compete with conventional SCC. Adapting the design to minimize the detrimental effects of by-products is therefore essential to promote sustainable SCC that is also commercially competitive., Spanish Ministry MCIU, AEI and ERDF [grant numbers PID 2020-113837RB-I00; 10.13039/501100011033; FPU17/03374]; the Junta de Castilla y León (Regional Government) and ERDF [grant number UIC-231, BU119P17]; Youth Employment Initiative (JCyL) and ESF [grant number UBU05B_1274]; and, finally, the University of Burgos [grant number SUCONS, Y135.GI].
Repositorio Institucional de la Universidad de Burgos (RIUBU)
Publicación Artículo científico (JournalArticle)

Porosity-based models for estimating the mechanical properties of self-compacting concrete with coarse and fine recycled concrete aggregate

  • Revilla Cuesta, Víctor
  • Faleschini, Flora
  • Zanini, Mariano A.
  • Skaf Revenga, Marta
  • Ortega López, Vanesa
Predicting the mechanical properties of Self-Compacting Concrete (SCC) containing Recycled Concrete Aggregate (RCA) generally depends, in great part, on the RCA fraction in use. In this study, predictive equations for estimating SCC mechanical properties are developed through SCC porosity indices, so they are applicable to any RCA fraction and amount that may be used. A total of ten SCC mixes were prepared, nine of which containing different proportions of coarse and/or fine RCA (0%, 50% or 100% for both fractions), and the tenth mixed with 100% coarse and fine RCA, and RCA powder 0–1 mm. The following properties were evaluated: compressive strength, modulus of elasticity, splitting tensile strength, flexural strength, and effective porosity as measured with the capillary-water-absorption test. Negative effects on the above properties were recorded for increasing contents of both RCA fractions. The application of simple regression models yielded porosity-based estimations of the mechanical properties of the SCC with an accuracy margin of ±20%, regardless of the RCA fraction and amount. The results of the multiple regression models with compressive strength as a secondary predictive variable presented even greater robustness with accuracy margins of ±10% and almost no significant effect of accidental porosity variations on prediction accuracy. Furthermore, porosity predictions using the 24-h effective water also yielded accurate estimations of all the above mechanical properties. Finally, comparisons with the results of other studies validated the reliability of the models and their accuracy, especially the minimum expected values at a 95% confidence level, at all times lower than the experimental results., Spanish Ministry of Universities within the framework of the State Program for the Promotion of Talent and its Employability in R + D + i, State Mobility Subprogram, of the State Plan for Scientific and Technical Research and Innovation 2017–2020 [PRX21/00007]; the Spanish Ministry MCI, AEI, EU and ERDF [grant numbers PID2020-113837RB-I00; 10.13039/501100011033; FPU17/03374]; the Junta de Castilla y León (Regional Government) and ERDF [grant numbers UIC-231; BU119P17]; Youth Employment Initiative (JCyL) and ESF [grant number UBU05B_1274]; and finally, the University of Burgos [grant numbers SUCONS, Y135.GI] and the University of Padova.
Repositorio Institucional de la Universidad de Burgos (RIUBU)
Publicación Artículo científico (JournalArticle)

Effect of the maturity of recycled aggregates on the mechanical properties and autogenous and drying shrinkage of high-performance concrete

  • Revilla Cuesta, Víctor
  • Evangelista, Luís
  • Brito, Jorge de
  • Ortega López, Vanesa
  • Manso Villalaín, Juan Manuel
The high cement content of high-performance concrete (HPC) results in improved strength, but also in large shrinkage. The substitution of natural aggregates (NA) with recycled aggregates (RA) notably affects these properties in conventional concrete. This study intends to analyse the effect of the content of RA and their maturity (time elapsed between casting and crushing of the parent concrete from which RA are obtained) on these properties of HPC. To this end, five mixes were manufactured with 0%, 25%, and 100% of coarse and fine RA of different maturities, 7 days (early-age RA) and 6 months (matured RA). The mechanical properties and the autogenous, drying, and total shrinkage of all mixes were determined. Both the increase of RA content and the lower stiffness and strength of early-age RA relative to matured RA worsened the mechanical behaviour of HPC. Regarding shrinkage, the lower stiffness and higher water absorption of matured RA compared to NA decreased autogenous shrinkage by 20%, but increased drying and total shrinkage. The lower stiffness of early-age RA and their shrinkage amplified all types of shrinkage of HPC around 10–20%. Nevertheless, the hydration of their unhydrated cement particles during the mixing process reduced those increases from what was expected. Total shrinkage of early-age recycled aggregate HPC could be estimated from the shrinkage of both a HPC mix of identical composition but with matured RA and the parent concrete. Overall, it can be concluded that RA’s maturity affects the mechanical performance and, especially, the shrinkage of HPC, so it should be considered when using this type of aggregate., Spanish Ministry MCIU, AEI and ERDF [grant numbers FPU17/03374; EST19/00263]. The authors also acknowledge the support of the Foundation for Science and Technology, CERIS Research Centre and Instituto Superior Técnico, the Junta de Castilla y León [grant number UIC231], and the University of Burgos [grant number Y135.GI].
Repositorio Institucional de la Universidad de Burgos (RIUBU)
Publicación Artículo científico (JournalArticle)

Models for compressive strength estimation through non-destructive testing of highly self-compacting concrete containing recycled concrete aggregate and slag-based binder

  • Revilla Cuesta, Víctor
  • Skaf Revenga, Marta
  • Serrano López, Roberto
  • Ortega López, Vanesa
Indirect estimation of compressive strength through non-destructive testing is key to monitoring the strength of structural concretes used in construction and rehabilitation works. However, no models are available to perform this estimation in highly Self-Compacting Concrete (SCC) with Recycled Concrete Aggregate (RCA). To fill this gap, two indirect measures were tested in this paper, the hammer rebound index and Ultrasonic Pulse Velocity (UPV), to predict the compressive strength of highly SCC. To do so, 24 SCC mixes were developed with different aggregate powders, binders, such as Ground Granulated Blast Furnace Slag (GGBFS), and contents of fine RCA. Compressive strength, and both indirect measures of all mixtures were determined at 1, 7, 28, and 90 days. The development of specific models for highly SCC responded to the inappropriateness of conventional models that are not adapted to its high fines content. Modelling as a function of either UPV or the hammer rebound index yielded accurate predictions, although the UPV model proved more sensitive to compositional changes and presented higher uncertainty. The best predictions were modelled by combining both indirect measures. The models provided safe and accurate indirect estimations of the compressive strength of high flowability SCC in real structures., Spanish Ministry MCIU, AEI and ERDF [grant number FPU17/03374]; the Junta de Castilla y León (Regional Government) and ERDF [grant number UIC-231, BU119P17]; Youth Employment Initiative (JCyL) and ESF [grant number UBU05B_1274]; and, finally, the University of Burgos [grant number SUCONS, Y135.GI].
Repositorio Institucional de la Universidad de Burgos (RIUBU)
Publicación Artículo científico (JournalArticle)

Assessment of longitudinal and transversal plastic behavior of recycled aggregate self-compacting concrete: A two-way study

  • Revilla Cuesta, Víctor
  • Skaf Revenga, Marta
  • Santamaría, Amaia
  • Ortega López, Vanesa
  • Manso Villalaín, Juan Manuel
Plastic strain behavior in the transversal direction to the axis of loading has often been underestimated in concrete design and its strength performance. However, as this article demonstrates, it is fundamental to define the viability of using concrete of a certain composition in real applications. In this study, 15 Self-Compacting Concrete (SCC) mixtures produced with Recycled Concrete Aggregate (RCA) and Ground Granulated Blast Furnace Slag (GGBFS) were subjected to a monotonic-load test and a 5-cycle loading/unloading test with increasing maximum loads. Continuous monitoring of the applied loads and the SCC strain was performed. In the transversal direction, these tests caused the appearance of a yield step, cracking by vertical splitting, and higher levels of deformability than in the longitudinal direction. It was concluded that the RCA content of SCC should be defined according to serviceability conditions when used in compressed elements, to safeguard against failure due to transversal plastic strain., Spanish Ministry MCIU, AEI and ERDF [grant numbers FPU17/03374 and RTI2018-097079-B-C31; 10.13039/501100011033]; the Junta de Castilla y León (Regional Government) and ERDF [grant number UIC-231, BU119P17]; Youth Employment Initiative (JCyL) and ESF [grant number UBU05B_1274]; the University of Burgos [grant number SUCONS, Y135.GI], UPV/EHU (PPGA20/26) and, finally, our thanks also to the Basque Government research group IT1314-19.
Repositorio Institucional de la Universidad de Burgos (RIUBU)
Publicación Artículo científico (JournalArticle)

Fiber-reinforcement and its effects on the mechanical properties of high-workability concretes manufactured with slag as aggregate and binder

  • Ortega López, Vanesa
  • García Llona, Aratz
  • Revilla Cuesta, Víctor
  • Santamaría, Amaia
  • San José Lombera, José Tomás
The feasibility of manufacturing fiber-reinforced concretes of high workability through additions of high volumes of electric arc furnace steel slag is evaluated in this paper, using sustainable binders with ground granulated blast furnace slag and ladle furnace slag as a supplementary cementitious material. An extensive experimental plan is developed to test four (self-compacting and pumpable) concrete mixtures, some reinforced with 0.5% vol. of (metallic or synthetic) fibers, in both the fresh and the hardened state. Very specific mechanical aspects are examined, such as the evaluation of both longitudinal and transversal stress-strain compressive behavior, and the assessment of direct tensile strength through the “dog-bone” test. The results of testing this sustainable concrete design yielded suitable mechanical strengths, and good toughness, ductility and impact strength, among other properties. Good adhesion between the fibers and the cementitious matrix was also evident from the fiber pull-out test results. Finally, the overall results confirmed that the use of electric arc furnace steel slag can make a real contribution to construction-sector sustainability and that the mechanical behavior of these novel concretes meets the basic design requirements for use in real structures., Spanish Ministries MCI, AEI, EU and ERDF [RTI2018-097079-B-C31; 10.13039/501100011033; FPU17/03374]; the Junta de Castilla y León (Regional Government) and ERDF [UIC-231, BU119P17]; the Basque Government research group [IT1314-19]; Youth Employment Initiative (JCyL) and ESF [UBU05B_1274]; the University of Burgos [Y135.GI] and the University of the Basque Country [PPGA20/26]. Likewise, our thanks to CHRYSO and HORMOR for supplying the materials used in this research.
Repositorio Institucional de la Universidad de Burgos (RIUBU)
Publicación Artículo científico (JournalArticle)

Mechanical performance and autogenous and drying shrinkage of MgO-based recycled aggregate high-performance concrete

  • Revilla Cuesta, Víctor
  • Evangelista, Luís
  • Brito, Jorge de
  • Skaf Revenga, Marta
  • Ortega López, Vanesa
The high strength and durability of high-performance concrete (HPC) may be significantly reduced by shrinkage cracking. The use of reactive magnesium oxide (MgO) can reduce shrinkage of cement-based materials due to its expansive properties. This study intends to analyse the validity of MgO as shrinkage-reducing agent in recycled aggregate HPC. To do so, ten HPC mixes with 0%, 25%, and 100% of both early-age (7-days air curing) and matured (6-month air curing) RA were produced. In half of the mixes, 10% ordinary Portland cement was replaced with MgO. The use of MgO slightly worsened the mechanical behaviour of HPC, especially when combined with large amounts of RA. On the other hand, the expansion of MgO fully offset the autogenous shrinkage of HPC and reduced total shrinkage by around 20–40%. Water storage of RA, and its deferred release over time, produced a more efficient hydration of MgO, which in turn led to a further reduction of autogenous shrinkage. However, the increase of drying shrinkage caused by RA was greater than this decrease of autogenous shrinkage due to MgO, so the higher the RA content of HPC the lower the total shrinkage reduction when adding MgO. Thus, the decrease of total shrinkage caused by MgO was compensated by the shrinkage increase because of RA when adding amounts above 35% early-age RA and 42% matured RA. Therefore, despite the suitability of MgO as shrinkage-reducing agent in recycled aggregate HPC, its effectiveness was reduced with increasing amounts of RA., Spanish Ministry of Universities, MICINN, AEI and ERDF [grant numbers FPU17/03374; EST19/00263; PID2020-113837RB-I00; 10.13039/501100011033]. The authors also acknowledge the support of the Foundation for Science and Technology, CERIS Research Centre and Instituto Superior Técnico, the Junta de Castilla y León [grant number UIC231], and the University of Burgos [grant number Y135.GI].
Repositorio Institucional de la Universidad de Burgos (RIUBU)
Publicación Artículo científico (JournalArticle)

Validation of slag-binder fiber-reinforced self-compacting concrete with slag aggregate under field conditions: Durability and real strength development

  • Ortega López, Vanesa
  • Faleschini, Flora
  • Pellegrino, Carlo
  • Revilla Cuesta, Víctor
  • Manso Villalaín, Juan Manuel
The environmental conditions to which a concrete may be exposed will condition its real range of use. Thus, concrete behavior must, at all times, be verified under a wide variety of environmental conditions, in order to ensure its real applicability. In this study, the real strength development and durability behavior of a fiber-reinforced self-compacting concrete is analyzed. This particular concrete incorporates 100% coarse (4/12 mm) and fine (0/4 mm) Electric Arc Furnace Slag (EAFS) as aggregate, as well as limestone fines as aggregate powder (0/1.18 mm). Furthermore, Ground Granulated Blast Furnace Slag (GGBFS) was also added as binder. Four mixtures with and without either metallic or synthetic fibers, and different GGBFS contents were designed. Real strength development was evaluated in all the mixes by comparing the strength development of both cores extracted from full-scale beams and wet-cured laboratory specimens. The durability behavior was analyzed by Mercury Intrusion Porosimetry (MIP), freeze/thaw, moist/dry, sulfate-attack, chloride-penetration, carbonation, and SO2-attack tests. On the one hand, the long-term mechanical properties of the cores (real conditions) were similar to the properties of the specimens cured in a moist chamber for 90 days in all the mixes. On the other, the increase in water content when adding fibers to maintain flowability, as well as the addition of GGBFS, resulted in an increase in MIP porosity. Therefore, the use of fibers, both metallic and synthetic, slightly worsened the durability behavior of the concrete, facilitating the entry of aggressive external agents. Nevertheless, the increased flexibility of the cementitious matrix when adding GGBFS was beneficial against moist/dry and sulfate-attack phenomena, despite the increase in porosity. Overall, the mixes complied with the regulatory requirements for use in aggressive environments, although the amounts of fibers and GGBFS should be carefully studied., Spanish Ministry of Universities within the framework of the State Program for the Promotion of Talent and its Employability in R + D + i, State Mobility Subprogram, of the State Plan for Scientific and Technical Research and Innovation 2017-2020 [PRX21/00007]; the Spanish Ministry of Universities, MICINN, AEI, EU and ERDF [grant numbers PID2020-113837RB-I00; 10.13039/501100011033; FPU17/03374]; the Junta de Castilla y León (Regional Government) and ERDF [grant numbers UIC-231; BU119P17]; Youth Employment Initiative (JCyL) and ESF [grant number UBU05B_1274]; and finally, to the University of Burgos [grant numbers SUCONS, Y135.GI] and the University of Padova.
Repositorio Institucional de la Universidad de Burgos (RIUBU)
Publicación Artículo científico (JournalArticle)

Shear strength assessment of reinforced concrete components containing EAF steel slag aggregates

  • Santamaría, Amaia
  • Romera, Jesús María
  • Marcos, Ignacio
  • Revilla Cuesta, Víctor
  • Ortega López, Vanesa
Electric Arc Furnace (EAF) slag can be reused as aggregate in Portland cement concrete mixes. The addition of EAFS and other waste co-products (fly ash, blast furnace slag) will modify the binding properties and will, importantly, enhance the global sustainability of such concretes. These mix designs offer acceptable pumpability and self-compaction in the fresh state and can be reinforced with fibers. In this study, eight different concrete mixes are designed within the range of medium-strength concretes (30–50 MPa) and are characterized in both the fresh and the hardened state. Large concrete volumes are used to pour reinforced beams, which are then subjected to small-span high-load tests to evaluate their resistance to shear stress, by analyzing two types of transversal (shear) reinforcement. The tests yielded promising results, contributing additional evidence on the viability of using recycled EAFS aggregate in structural applications. The mechanical behavior of these concretes was closely correlated with the strength predictions calculated with the formulas listed in various international standards., Spanish Ministry of Universities, MICINN, AEI, EU and ERDF [PID2020-113837RB-I00; RTI2018-097079-B-C31; 10.13039/501100011033; FPU17/03374]; the Junta de Castilla y León and ERDF [UIC-231, BU119P17]; Youth Employment Initiative (JCyL) and ESF [UBU05B_1274]; the University of Burgos [grant number SUCONS, Y135.GI], and, finally, our thanks also go to the SAREN research group (IT1619-22, Basque Government).
Repositorio Institucional de la Universidad de Burgos (RIUBU)
Publicación Contribución de congreso (ConferenceOutput)

Bituminous base courses for flexible pavements with steel slags

  • Skaf Revenga, Marta
  • Bartolomé González, Javier
  • Gonzalo Orden, Hernán
  • Linares Unamunzaga, Alaitz
  • Ortega López, Vanesa
  • Manso Villalaín, Juan Manuel
Trabajo presentado en: R-Evolucionando el transporte, XIV Congreso de Ingeniería del Transporte (CIT 2021), realizado en modalidad online los días 6, 7 y 8 de julio de 2021, organizado por la Universidad de Burgos, The purpose of this research was to study the feasibility of incorporating steel slags into coarse bituminous mixtures. The objective was twofold: to reduce dependence on natural aggregates, and to provide a use for industrial by-products. The slags studied come from the manufacture of carbon steel in electric furnaces and are divided into two types: Electric Arc Furnace (EAF) slag and Ladle Furnace (LF) slag. The mixture designed is coarse bituminous concrete (AC22G), for base courses in flexible pavements. In a first phase, the physical characterization of the materials was carried out to check their suitability. In a second phase, three types of mixes were designed: a control mix (made with natural limestone aggregates), a mix where LF slag was introduced to replace the filler and the fine fraction (sand) of the mix; and finally, the feasibility of manufacturing a totally sustainable mix was analyzed, which would fully incorporate EAF slag as coarse aggregate and LF slag as fine aggregate and filler. In a third and final phase, the designed mixes were subjected to different mechanical, water sensitivity, and durability tests. The research demonstrated that the incorporation of EAF and LF steel slag as a substitute for natural aggregate in coarse bituminous mixtures is feasible, meeting regulatory requirements, improving sustainability in the construction industry, as well as reducing emissions, and contributing to climate change mitigation., This work was supported by the Junta de Castilla y León (Regional Government) and ERDF [grant number UIC-231, BU119P17] and the University of Burgos [grant number SUCONS, Y135.GI].
Repositorio Institucional de la Universidad de Burgos (RIUBU)
Publicación Artículo científico (JournalArticle)

Elastic stiffness estimation of aggregate–ITZ system of concrete through matrix porosity and volumetric considerations: explanation and exemplification

  • Revilla Cuesta, Víctor
  • Skaf Revenga, Marta
  • Santamaría, Amaia
  • Romera, Jesús María
  • Ortega López, Vanesa
The modulus of elasticity of a concrete depends on the elastic stifness of both the cementitious matrix and the aggregate–ITZ system, which includes any slippage mechanisms under loading between the aggregate and the cementitious matrix within the interfacial transition zone (ITZ). A procedure is presented in this paper to estimate the elastic stifness of an aggregate–ITZ system within a cementitious matrix, by considering the relative volumes and the porosities of the concrete components. The method was validated by determining the elastic stifness of both the limestone–ITZ and the electric arc furnace slag (EAFS)–ITZ systems when embedded in a slag-based cementitious matrix. The greater stifness of the EAFS–ITZ system in comparison with the natural aggregate system explained the higher strength and modulus of elasticity of the concrete following additions of EAFS. Moreover, having determined those parameters, the elastic moduli of concretes with a similar cementitious matrix could then be accurately estimated., Open Access funding provided thanks to the CRUE-CSIC agreement with Springer Nature. The authors wish to express their gratitude for funding this research work to the Spanish Ministry of Universities, MICINN, AEI, EU and ERDF [PID2020-113837RBI00; PID2021-124203OB-I00; RTI2018-097079-B-C31; 10.13039/501100011033; FPU17/03374]; the Junta de Castilla y León (Regional Government) and ERDF [UIC-231, BU119P17]; the Basque Regional Government through the consolidated research group SAREN [IT1619-22]; Youth Employment Initiative (JCyL) and ESF [UBU05B_1274]; and, fnally, the University of Burgos [Y135.GI].
Repositorio Institucional de la Universidad de Burgos (RIUBU)
Publicación Artículo científico (JournalArticle)

Deformational behavior of self-compacting concrete containing recycled aggregate, slag cement and green powders under compression and bending: Description and prediction adjustment

  • Revilla Cuesta, Víctor
  • Ortega López, Vanesa
  • Skaf Revenga, Marta
  • Khan, Asadur Rehman
  • Manso Villalaín, Juan Manuel
The high fine-aggregate content of Self-Compacting Concrete (SCC) means that its deformational behavior differs from that of vibrated concrete. SCC performance is further altered when industrial by-products are used as raw materials in those fractions. In this paper, the aim is to analyze and to model the deformational behavior under compression and bending of SCC containing 100% coarse and 0%, 50%, and 100% fine Recycled Aggregate (RA), limestone and RA green aggregate powders sized 0/0.5 mm, and Ground Granulated Blast-furnace Slag (GGBS) cement. After the fresh and mechanical characterization of the 18 SCC mixes that were produced, their compressive stress-strain and bending load-deflection curves were determined by continuously recording the applied load and the strain/deflection values of the SCC test specimens. 100% coarse RA yielded deformability levels in accordance with international standards, while higher fine RA contents increased deformation under compression and reduced it under flexural stress. SCC stiffness increased when GGBS was added, due to the adjustment of the proportion of cementitious matrix, while the use of limestone powder and, especially, RA powder had the opposite effect. Both compressive strain and flexural deflection were underestimated with existing theoretical models. However, the incorporation in the models of both exponential correction coefficients, dependent on the fine RA content, and partial adjustment coefficients, dependent on the types of cement and aggregate powder, produced optimal fits with the experimental stress-strain and load-deflection curves. In view of the deformational behavior, which was successfully modelled with maximum deviations of ±10%, fine RA may be used in combination with GGBS and limestone powder, although it is recommended that fine RA should not exceed proportions of 50%., The authors wish to express their gratitude for funding this research work to the Spanish Ministry of Universities, MICINN, AEI, EU, and ERDF [PID2020-113837RB-I00; 10.13039/501100011033; FPU17/03374]; the Junta de Castilla y Leon ´ (Regional Government) and ERDF [UIC-231]; and the University of Burgos [SUCONS, Y135. GI].
Repositorio Institucional de la Universidad de Burgos (RIUBU)
Publicación Artículo científico (JournalArticle)

Using recycled aggregate concrete at a precast-concrete plant: A multi-criteria company-oriented feasibility study

  • Revilla Cuesta, Víctor
  • Fiol Olivan, Francisco
  • Perumal, Priyadharshini
  • Ortega López, Vanesa
  • Manso Villalaín, Juan Manuel
Numerous test results at laboratory scale confirm the utility of Recycled Aggregate (RA) for the development of concrete that demonstrates durability and adequate in-fresh and mechanical behavior. However, feasibility evaluations of the use of RA in real industrial applications are necessary, before any large-scale industrial application of these products can begin. In this research, the feasibility of producing precast-concrete components containing large amounts of coarse RA at a precast-concrete plant is analyzed. Two Self-Compacting Concretes (SCC) were produced incorporating 0% and 100% coarse RA, respectively, at both laboratory scale (0.08 m3 ) and industrial scale (2 m3 ). Work took place at the industrial-scale facilities of a precast-concrete company that was collaborating in this study. Flowability and mechanical behavior were maintained as concrete production volumes increased, and concrete strength even increased after adding coarse RA, due to a careful mix design. However, the durability performance worsened by around 20% when produced at industrial scale, being this worsening higher whether coarse RA was used. A Multi-Criteria Decision-Making (MCDM) analysis, in which the criteria of the precast-concrete company defined the relative importance of each concrete property, showed the feasibility of manufacturing precast-SCC components containing coarse RA for interior usage, whose fundamental requirement is adequate mechanical strength. The results of the MCDM analysis also underlined the lower cost of coarse RA, making its use in SCC components cast with large concrete volumes advisable. Overall, the addition of coarse RA in the precast-concrete industry is recommended in the interests of a greener construction sector., The authors wish to express their gratitude for funding this research work to the Spanish Ministry of Universities, MICINN, AEI, EU, ERDF and NextGenerationEU/PRTR [PID2020-113837RB-I00; 10.13039/ 501100011033; TED2021-129715B-I00; FPU17/03374]; the Junta de Castilla y Leon ´ (Regional Government) and ERDF [UIC-231]; and the University of Burgos [SUCONS, Y135.GI]. In addition, Priyadharshini Perumal acknowledges the financial support received from the project DeConcrete [grant # KO 4068: Eco-efficient Arctic technologies cooperation] funded by the Kolarctic CBC initiative of the European Union. Finally, the support and assistance of ARTEPREF S.A. for the development of this study is also highly appreciated.
Repositorio Institucional de la Universidad de Burgos (RIUBU)
Publicación Artículo científico (JournalArticle)

Shrinkage prediction of recycled aggregate structural concrete with alternative binders through partial correction coefficients

  • Revilla Cuesta, Víctor
  • Evangelista, Luís
  • Brito, Jorge de
  • Skaf Revenga, Marta
  • Manso Villalaín, Juan Manuel
Estimating the shrinkage of structural concrete is essential to calculate, at the design stage, the stresses that a structure may experience due to this phenomenon. Nevertheless, changes in composition, as well as the use of wastes as raw materials, alter the shrinkage behaviour of concrete and render invalid shrinkage-prediction models from the standards. This paper shows a procedure to estimate the shrinkage of recycled aggregate concrete made with alternative binders. This procedure is based on modifying the shrinkage estimated through the Eurocode 2 or ACI 209.2R models by multiplying it by a partial correction coefficient for every change in concrete composition. The application of this procedure to high-performance and self-compacting concretes made with various contents of recycled aggregate of different maturity, reactive magnesium oxide and ground granulated blast furnace slag showed that it is suitable for estimating long-term shrinkage with maximum deviations of ±10%. However, to obtain an adequate accuracy, it is necessary to bear in mind some tips, such as the need to consider the prediction interactions between the factors, the usefulness of the natural logarithm of the concrete age to improve the estimation accuracy or the convenience of introducing a concrete-age-dependent coefficient to reach accurate shrinkage estimations at early ages. Finally, the partial correction coefficients are found to be of a simpler nature for the ACI 209.2R model, so this model is recommended for predicting the shrinkage of recycled aggregate concrete., This work was supported by the Spanish Ministry of Universities, MICINN, AEI, EU and ERDF [grant numbers PID2020-113837RB-I00; 10.13039/501100011033; FPU17/03374; EST19/00263]. Moreover, the authors acknowledge the support of the Junta de Castilla y León [grant number UIC231]; the University of Burgos [grant number Y135. GI]; and the Foundation for Science and Technology, CERIS Research Centre and Instituto Superior Técnico.
Repositorio Institucional de la Universidad de Burgos (RIUBU)
Publicación Artículo científico (JournalArticle)

Quantification and characterization of the microstructural damage of recycled aggregate self-compacting concrete under cyclic temperature changes

  • Revilla Cuesta, Víctor
  • Skaf Revenga, Marta
  • Chica Páez, José Antonio
  • Ortega López, Vanesa
  • Manso Villalaín, Juan Manuel
Recycled Aggregate (RA) usually increases porosity and weakens Interfacial Transition Zones (ITZs) of concrete, which favors the appearance of internal thermal damage. Four Self-Compacting Concrete (SCC) mixes with coarse and fine RA were subjected to positive and negative cyclic temperature variations to characterize their thermal damage and quantify its effects. Two damage mechanisms were found. On the one hand, micro-cracks appeared in the ITZs. On the other hand, micro-cracks arose from the micro-pores and propagated through the cementitious matrix. Both damage mechanisms were promoted by the use of coarse and fine RA, respectively. The damage was most notable at sub-zero temperatures and when adding coarse RA. Furthermore, it primarily affected compressive strength, although ultrasonic pulse velocity and hardened density also decreased, which served as non-destructive indicators to indirectly quantify the level of thermal internal damage of SCC., This work was funded by MICINN, AEI, EU, ERDF and NextGenerationEU/PRTR [PID2020-113837RB-I00; 10.13039/501100011033; TED2021-129715B-I00; FPU17/03374]; JCyL and ERDF [UIC-231]; and the University of Burgos [SUCONS, Y135.GI].
Repositorio Institucional de la Universidad de Burgos (RIUBU)
Publicación Artículo científico (JournalArticle)

Hammer rebound index as an overall-mechanical-quality indicator of self-compacting concrete containing recycled concrete aggregate

  • Revilla Cuesta, Víctor
  • Ortega López, Vanesa
  • Faleschini, Flora
  • Espinosa González, Ana Belén
  • Serrano López, Roberto
The hammer rebound index has traditionally been solely and exclusively used to estimate the compressive strength of vibrated concrete. Its use has recently been extended to the prediction of the compressive strength of Self-Compacting Concrete (SCC) and concrete produced with Recycled Concrete Aggregate (RCA). The conventional use of the hammer-rebound test is further developed in this paper, by demonstrating how it can be used to estimate the overall mechanical behavior of SCC containing RCA. To do so, nine SCC mixes with different contents and fractions (coarse, fine, and powder) of RCA are analyzed. Following a simple-linear-regression validation and property standardization procedure, the hammer rebound index is then expressed as a linear combination of four mechanical properties, adjusted through a multiple regression. The hammer rebound index is therefore expressed as a weighting of both the mean value of compressive behavior (arithmetic mean of compressive strength and modulus of elasticity) amounting to a weight of 72.8%, and the mean value of bendingtensile behavior (arithmetic mean of splitting tensile strength and flexural strength) amounting to a weight of 27.2%. The hammer rebound index can therefore be construed as an overall-mechanical-quality performance indicator of the SCC containing RCA, which can also yield predictions of every mechanical property. In this way, the application of the hammer rebound index could likewise be of use in rehabilitation, pathology, and healthmonitoring works where a full characterization of the mechanical performance of SCC with RCA is required, facilitating the use of SCC with RCA in real structures., The authors wish to express their gratitude to the following government ministries, agencies, and universities for funding this research: the Spanish Ministry of Universities, MICIN, AEI, EU, ERDF and NextGenerationEU/ PRTR [PID2020-113837RB-I00; 10.13039/501100011033; TED2021- 129715B-I00; FPU17/03374; PRX21/00007]; the Junta de Castilla y León (Regional Government) and ERDF [UIC-231, BU119P17]; the University of Burgos [SUCONS, Y135.GI]; and, finally, the University of Padova.
Repositorio Institucional de la Universidad de Burgos (RIUBU)
Publicación Artículo científico (JournalArticle)

Multi-parametric flowability classification of self-compacting concrete containing sustainable raw materials: An approach to real applications

  • Revilla Cuesta, Víctor
  • Skaf Revenga, Marta
  • Ortega López, Vanesa
  • Manso Villalaín, Juan Manuel
Adding sustainable raw materials to Self-Compacting Concrete (SCC) modifies its flowability behavior. Furthermore, the use of these raw materials may at the same time even improve one fresh property while worsening another. An accurate flowability description of SCC containing sustainable raw materials therefore requires a multi-parametric classification that simultaneously covers all fresh properties (slump flow, viscosity, and blocking ratio) for an accurate description of its potential applications. Existing classifications consider each fresh property independently. In this paper, a multi-parametric flowability classification of SCC containing sustainable raw materials is proposed. The effects of multiple sustainable raw materials on SCC flowability are compiled in a dataset serving as a knowledge base with information on 663 SCC mixes containing sustainable aggregates and binders. The statistical analysis of the dataset led to the definition of three types of flowability zones. Firstly, the overall-flowability zones, in which SCC flowability is described in absolute terms: the better the in-fresh properties, the better the overall-flowability zone. Secondly, the flowability-balance zones reflect the balance between free flow (slump flow and slump-flow viscosity) and flow around obstacles (V-funnel emptying time and L-box blocking ratio). Finally, SCC is classified within flowability-predominance zones, which define the main characteristic of SCC flowability, rate of flow (viscosity) or uniformity of flow (spreading). The variability of the effect of each sustainable raw material on the flowability of SCC makes this classification useful, in so far as it offers a complete picture of the fresh behavior of SCC in which all fresh properties are simultaneously considered. Furthermore, based on the description in the proposed classification of overall flowability and the balance between free flow and flow around obstacles, the application fields are defined for which the use of each SCC mix with sustainable raw materials is recommended., This research work was supported by the Spanish Ministry of Universities, MICINN, AEI, EU, ERDF and NextGenerationEU/PRTR [grant numbers PID2020-113837RB-I00; 10.13039/501100011033; TED2021-129715B–I00; FPU17/03374]; the Junta de Castilla y León (Regional Government) and ERDF [grant number UIC-231]; and, finally, the University of Burgos [grant number SUCONS, Y135. GI].
Repositorio Institucional de la Universidad de Burgos (RIUBU)
Publicación Artículo científico (JournalArticle)

Utility of Ultrasonic Pulse Velocity for Estimating the Overall Mechanical Behavior of Recycled Aggregate Self-Compacting Concrete

  • Espinosa González, Ana Belén
  • Revilla Cuesta, Víctor
  • Skaf Revenga, Marta
  • Faleschini, Flora
  • Ortega López, Vanesa
Ultrasonic pulse velocity (UPV) is a non-destructive measurement technique with which the quality of any concrete element can be evaluated. It provides information on concrete health and for assessing the need for repair in a straightforward manner. In this paper, the relationship is studied between UPV readings and the mechanical behavior of self-compacting concrete (SCC) containing coarse, fine, and/or powdery RA. To do so, correlations and simple- and multipleregression relationships between compressive strength, modulus of elasticity, splitting tensile strength, flexural strength, and UPV readings of nine SCC mixes were assessed. The correlations showed that the relationship of UPV with any mechanical property was fundamentally monotonic. The inverse square-root model was therefore the best-fitting simple-regression model for all the mechanical properties, although for bending-tensile-behavior-related properties (splitting tensile strength and flexural strength) the estimation accuracy was much lower than for compressive-behavior-related properties (compressive strength and modulus of elasticity). Linear-combination multiple-regression models showed that the properties related to bending-tensile behavior had a minimal influence on the UPV value, and that their introduction resulted in a decreased estimation accuracy. Thus, the multiple-regression models with the best fits were those that linked the compressive-behavior-related properties to the UPV readings. This therefore enables the estimation of the modulus of elasticity when the UPV and compressive strength are known with a deviation of less than ±20% in 87% of the SCC mixes reported in other studies available in the literature., This research was funded by the Spanish Ministry of Universities, MICIN, AEI, EU, ERDF, and NextGenerationEU/PRTR, grant numbers PID2020-113837RB-I00, 10.13039/501100011033, and TED2021-129715B-I00; the Junta de Castilla y León (Regional Government) and ERDF, grant number UIC-231; and the University of Burgos, grant numbers SUCONS, Y135.GI.
Repositorio Institucional de la Universidad de Burgos (RIUBU)
Publicación Artículo científico (JournalArticle)

Effects of temperature and moisture fluctuations for suitable use of raw-crushed wind-turbine blade in concrete

  • Revilla Cuesta, Víctor
  • Hurtado Alonso, Nerea
  • Manso Morato, Javier
  • Serrano López, Roberto
  • Manso Villalaín, Juan Manuel
Raw-crushed wind-turbine blade (RCWTB), a waste from the recycling of wind-turbine blades, is used as a raw material in concrete in this research. It contains not only fiberglass-composite fibers that bridge the cementitious matrix but also polyurethane and balsa-wood particles. Therefore, concrete containing RCWTB can be notably affected by moisture and temperature fluctuations and by exposure to high temperatures. In this research, the performance of five concrete mixes with 0.0%, 1.5%, 3.0%, 4.5%, and 6.0% RCWTB, respectively, is studied under moist/dry, alternating-sign-temperature-shock, and high-temperature-shock tests. Two damage mechanisms of RCWTB within concrete were found through these tests: on the one hand, micro-cracking of the cementitious matrix, which was verified by microscopic analyses and was dependent on concrete porosity; on the other, damage and degradation of the RCWTB components, as the polyurethane melted, and the balsa-wood particles burned. Both phenomena led to larger remaining-strain levels and reduced concrete compressive strength by up to 25% under temperature and humidity variations, although the bridging effect of the fiberglass-composite fibers was effective when adding RCWTB amounts higher than 3.0%. The compressive-strength loss after the high-temperature-shock test increased with the RCWTB content, reaching maximum values of 8% after an exposure time of 7 days. Statistical analyses revealed that effect of the RCA amount in the concrete was conditioned by the exposure times in all the tests. The accurate definition of those times is therefore key to set an RCWTB content in concrete that ensures its suitable behavior under the environmental conditions analyzed., Open Access funding provided thanks to the CRUE-CSIC agreement with Springer Nature. This research work was funded by the Spanish Ministry of Universities, MICINN, AEI, EU, ERDF, and NextGenerationEU/PRTR [grant numbers PID2020-113837RB-I00, PID2023-146642OB-I00,https://doi.org/10.13039/501100011033, TED2021-129715B-I00, and FPU21/04364]; the Junta de Castilla y León (Regional Government) and ERDF [grant numbers UIC-231, BU033P, and3; BU066-22]; and, finally, the University of Burgos [grant number SUCONS, Y135.GI].
Repositorio Institucional de la Universidad de Burgos (RIUBU)
Publicación Artículo científico (JournalArticle)

Deepening the effect of selectively crushed wind-turbine blade on the dimensional stability and high-temperature resistance of concrete

  • Revilla Cuesta, Víctor
  • Skaf Revenga, Marta
  • Manso Morato, Javier
  • Hurtado Alonso, Nerea
  • Manso Villalaín, Juan Manuel
Selectively Crushed Wind-Turbine Blade (SCWTB) is obtained through knife crushing of panels from wind-turbine blades. Two thirds of SCWTB weight consist of GFRP-composite fibers, which may improve both dimensional stability and high-temperature resistance of concrete. In this investigation, the evaluation of such aspects in concrete containing 1.5 %, 3.0 %, 4.5 % and 6.0 % SCWTB by volume is addressed. For this purpose, plastic shrinkage, drying shrinkage, total shrinkage, and thermal expansion were evaluated regarding dimensional stability, while resistance to high temperatures was assessed through accelerated-aging and thermal-shock tests. The results revealed that 6.0 % SCWTB reduced by half concrete plastic shrinkage, and total shrinkage by 40–50 % at 7 days and by 10–20 % at 91 days. Furthermore, the initial thermal strain was decreased from SCWTB contents of 3.0 %, which in turn reduced the linear thermal expansion coefficient, which had a value of 1.49·10−5 °C−1 in concrete with 6.0 % SCWTB. Finally, concrete with SCWTB maintained adequate compressive strength after accelerated aging and air-heating thermal shock, reaching values above 40 MPa, and halved the loss of flexural strength when added in a content of 6.0 %. Scanning electron microscopy revealed that high temperatures caused micro-cracks that started in weak zones and propagated along the glass fibers of GFRP, but the bond between the cementitious matrix and the GFRP-composite fibers was ideal, so the matrix fractured instead of the fibers slipping when loading. The improvements induced by SCWTB were statistically significant, so this waste can be considered a value-added material in terms of the concrete behavior analyzed., This research work was supported by the Spanish Ministry of Science, Innovation and Universities MICIU, AEI, EU, ERDF and NextGenerationEU/PRTR [grant numbers PID2023-146642OB-I00; 10.13039/501100011033; TED2021-129715B-I00; FPU21/04364]; the Junta de Castilla y León (Regional Government) and ERDF [grant number UIC-231; BU033P23; BU066-22]; and, finally, the University of Burgos [grant number SUCONS, Y135.GI].
Repositorio Institucional de la Universidad de Burgos (RIUBU)
Publicación Artículo científico (JournalArticle)

Low-Strength Concrete with Raw-Crushed Wind Turbine Blade and Coarse Recycled Aggregate

  • Hurtado Alonso, Nerea
  • Manso Morato, Javier
  • Revilla Cuesta, Víctor
  • Skaf Revenga, Marta
  • Manso Villalaín, Juan Manuel
Nonselective crushing of wind turbine blades results in raw-crushed wind turbine blade (RCWTB), a material that can be used in concrete production. Wind farm decommissioning can also generate coarse recycled aggregate (CRA) from the demolition of wind turbine concrete footings. This paper proposes a first approach for the joint management of both wastes through their simultaneous use in low-strength concrete, with a target compressive strength of 25 MPa. Mixes with 50% and 100% CRA, and 0% and 10% RCWTB as a cement addition, were designed, with the effect of CRA content not being statistically significant, to analyze its interaction with RCWTB. The results showed that, on the one hand, RCWTB reduced strength and stiffness under compression by a maximum of 9%–15%, although the target strength was achieved in all mixes; the presence of balsa wood and polymer particles in RCWTB, with high flexibility, could explain these reductions. On the other hand, the stitching effect of the glass fiber–reinforced polymer fibers present in RCWTB largely improved the bending-tensile mechanical properties. For example, flexural strength was almost doubled (from 2.51 to 4.99 MPa) when RCWTB was combined with 50% CRA. Additionally, RCWTB reduced both the embodied carbon and cost of low-strength concrete, resulting in doubled flexural-strength efficiency (flexural strength per unit of embodied carbon and cost), regardless of the CRA content. Overall, the best interaction was observed with 10% RCWTB and 50% RCA. Therefore, this study opens the possibility of simultaneously using RCWTB and CRA in low-strength concrete for applications where bending stresses predominate., This research work was supported by the Ministerio de Ciencia, Innovación y Universidades (MICIU), Agencia Estatal de Investigación (AEI), European Union (EU), European Regional Development Fund (ERDF), and NextGenerationEU/PRTR (Grant Nos. PID2020-113837RB-I00, PID2023-146642OB-I00, 10.13039/501100011033, TED2021-129715B-I00, and FPU21/04364); the Junta de Castilla y León (Regional Government) and ERDF (Grant Nos. UIC-231, BU033P23, and BU066-22), and, finally, the University of Burgos (Grant No. SUCONS, Y135.GI). Authors Nerea Hurtado-Alonso and Javier Manso-Morato contributed equally to this paper.
Repositorio Institucional de la Universidad de Burgos (RIUBU)
Publicación Artículo científico (JournalArticle)

Long-term mechanical performance of concrete with high amounts of wind turbine blade mixed waste: Analysis of temporal evolution mechanisms

  • Manso Morato, Javier
  • Hurtado Alonso, Nerea
  • Serrano López, Roberto
  • Revilla Cuesta, Víctor
  • Ortega López, Vanesa
Fiber-Reinforced Concrete (FRC) was manufactured by the addition of high percentages of mechanically recycled wind-turbine blades, known as Raw-Crushed Wind-Turbine Blade (RCWTB). This sustainable material was added as aggregate replacement up to 10 % vol., while keeping the cement content equal for all mixes, and the effects on several fields were evaluated. First, strength (compressive, tensile splitting and flexural testing) and stiffness were evaluated at 7, 28, 90 and 180 days of age. Results showed that low RCWTB contents improved compressive (above 60 MPa) and tensile strengths (over 6.50 MPa under bending) due to enhanced matrix compactness. Nevertheless, the large proportions of deformable particles when using high RCWTB contents slightly hindered mechanical performance. Second, temporal strength development mechanism was evaluated through Scanning Electron Microscopy (SEM) on specimens that underwent mechanical testing and explained through schematics by the authors. This analysis revealed that the porous particles of RCWTB, acting as water reservoirs, accelerated matrix hydration and improved Interfacial Transition Zones (ITZ) around the Glass Fiber-Reinforced Polymer (GFRP) fibers of RCWTB, globally enhancing early-age strength. Third, low RCWTB levels improved abrasion resistance (up to 14.73 %), while high contents reduced surface quality but maintained acceptable performance. Finally, thermal conductivity remained stable following RCWTB incorporation at low levels and increased at higher contents (up to 35.75 %) but remained within typical FRC ranges. Therefore, this research ensures proper early-age and long-term overall performance of FRC produced with RCWTB, enhancing sustainability while yielding an improved concrete material suitable for a wide variety of applications., This research work was supported by the Spanish Ministry of Science, Innovation and Universities MICIU, AEI, EU, ERDF and NextGenerationEU/PRTR [grant numbers PID2023-146642OB-I00; 10.13039/501100011033; TED2021-129715B-I00; FPU21/ 04364]; the Junta de Castilla y León (Regional Government) and ERDF [grant number UIC-231; BU033P23; BU066-22]; and, finally, the University of Burgos [grant number SUCONS, Y135.GI].
Repositorio Institucional de la Universidad de Burgos (RIUBU)
Publicación Artículo científico (JournalArticle)

Multicriteria and response surface-based selection of coarse recycled aggregate and blade waste contents in environmentally friendly low-strength concrete

  • Revilla Cuesta, Víctor
  • Hernando Revenga, Manuel
  • Mourou, Chaimae
  • Serrano López, Roberto
The use of Coarse Recycled Aggregate (CRA) in Low-Strength Concrete (LSC), suitable for pavements, allows the sustainable revaluation of this waste material, but worsens its performance. Recycled fibers of Glass Fiber-Reinforced Polymer (GFRP) present in Raw-Crushed Wind-Turbine Blade (RCWTB) may counterbalance the detrimental effects caused by CRA addition. This research analyzes the mechanical properties, durability, cost and carbon footprint of LSC mixes with 50 % and 100 % CRA combined with 0 % and 10 % RCWTB. Stitching of the cementitious matrix by GFRP fibers improved flexural strength and energy absorption of LSC containing CRA. In addition, these fibers exerted a barrier effect against water passage and exhibited higher surface hardness, the addition of RCWTB therefore did not affect the water-absorption rate and effective porosity and increased the abrasion resistance of LSC. Finally, RCWTB also reduced the cost and carbon footprint of LSC. These enhancements caused by RCWTB were analyzed through Multi-Criteria Decision-Making (MCDM) and Response Surface Methodology (RSM), approaches novel in the literature. According to them, the joint use of CRA and RCWTB in LSC was recommended. PROMETHEE II algorithm indicated that the use of 10 % RCWTB combined with 100 % CRA was the best option due to economic and environmental advantages, as this algorithm only considered which LSC mixture was the best for each property. ELECTRE algorithm showed indifference between both CRA contents, due to the better mechanical and durability performance of 50 %-CRA LSC. TOPSIS algorithm and RSM models revealed a preference for 50 % CRA and 10 % RCWTB following quantitative calculations based on the magnitudes of the property differences between the mixes. This research demonstrates the broad suitability of LSC containing both CRA and RCWTB in construction applications, mainly regarding pavements., This research work was supported by grant TED2021-129715B-I00 funded by MICIU/AEI/10.13039/501100011033 and by European Union NextGenerationEU/PRTR; grant PID2023-146642OB-I00 funded by MICIU/AEI/10.13039/501100011033 and by ERDF/EU; grants UIC-231 and BU033P23 funded by the Junta de Castilla y León (Regional Government) and ERDF/EU; and grant SUCONS, Y135.GI funded by the University of Burgos.