Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 25
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Converse flexoelectricity yields large piezoresponse force microscopy signals in non-piezoelectric materials

  • Abdollahi, Amir
  • Domingo, Neus
  • Arias, Irene
  • Catalán, Gustau
Converse flexoelectricity is a mechanical stress induced by an electric polarization gradient. It can appear in any material, irrespective of symmetry, whenever there is an inhomogeneous electric field distribution. This situation invariably happens in piezoresponse force microscopy (PFM), which is a technique whereby a voltage is delivered to the tip of an atomic force microscope in order to stimulate and probe piezoelectricity at the nanoscale. While PFM is the premier technique for studying ferroelectricity and piezoelectricity at the nanoscale, here we show, theoretically and experimentally, that large effective piezoelectric coefficients can be measured in non-piezoelectric dielectrics due to converse flexoelectricity., G.C. and N.D. acknowledge financial support from ERC Starting grant 308023, from Plan Nacional project MINECO Grant MAT2016-77100-C2-1-P and FIS2015-73932-JIN and support of Generalitat de Catalunya (Grant No. 2017-SGR-579). ICN2 acknowledges support from the Severo Ochoa Program (MINECO, Grant SEV-2017-0706) and the CERCA Programme / Generalitat de Catalunya. I.A. acknowledges the support of the Generalitat de Catalunya through the prize “ICREA Academia” for excellence in research and of the European Research Council (StG-679451). I.A. and A.A. also acknowledge the support of Generalitat de Catalunya (Grant No. 2017-SGR-1278)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Switchable tribology of ferroelectrics

  • Cho, Seongwoo
  • Gaponenko, Iaroslav
  • Cordero-Edwards, Kumara
  • Barceló-Mercader, Jordi
  • Arias, Irene
  • Kim, Daeho
  • Lichtensteiger, Céline
  • Yeom, Jiwon
  • Musy, Loïc
  • Kim, Hyunji
  • Han, Seung Min
  • Catalán, Gustau
  • Paruch, Patrycja
  • Hong, Seungbum
Switchable tribological properties of ferroelectrics offer an alternative route to visualize and control ferroelectric domains. Here, we observe the switchable friction and wear behavior of ferroelectrics using a nanoscale scanning probe—down domains have lower friction coefficients and show slower wear rates than up domains and can be used as smart masks. This asymmetry is enabled by flexoelectrically coupled polarization in the up and down domains under a sufficiently high contact force. Moreover, we determine that this polarization-sensitive tribological asymmetry is widely applicable across various ferroelectrics with different chemical compositions and crystalline symmetry. Finally, using this switchable tribology and multi-pass patterning with a domain-based dynamic smart mask, we demonstrate three-dimensional nanostructuring exploiting the asymmetric wear rates of up and down domains, which can, furthermore, be scaled up to technologically relevant (mm–cm) size. These findings demonstrate that ferroelectrics are electrically tunable tribological materials at the nanoscale for versatile applications., S.H. acknowledges the National Research Foundation of Korea (NRF) grant funded by the Korean government (MSIT) (Grant No. 2020R1A2C2012078, NRF-2022K1A4A7A04095892 and RS-2023-00247245) and the KAIST-funded Global Singularity Research Program for 2022 and 2023. P.P. acknowledges Division II of the Swiss National Science Foundation under project 200021_178782. S.C. acknowledges the National Research Foundation of Korea (NRF) grant funded by the Korean government (NRF-2018-Global Ph.D. Fellowship Program). I.A. acknowledges the support of the European Research Council (No. StG-679451 to I.A.), the Spanish Ministry of Economy and Competitiveness (No. RTI2018-101662-B-I00), and the Generalitat de Catalunya (ICREA Academia award for excellence in research to I.A. and Grant No. 2017-SGR-1278 to I.A.). CIMNE is a Severo Ochoa Centre of Excellence (2019-2023) under the grant CEX2018-000797-S to I.A. funded by MCIN/AEI/10.13039/501100011033., With funding from the Spanish government through the "Severo Ochoa Centre of Excellence" accreditation (CEX2018-000797-S)., Peer reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Contribución de congreso (ConferenceOutput)

Coupling of continuous and HDG methods

  • Paipuri, Mahendra
  • Tiago, Carlos
  • Fernández Méndez, Sonia|||0000-0002-9305-7684
A coupling strategy between hybridizable discontinuous Galerkin (HDG) and continuous Galerkin (CG) methods is proposed in the framework of second-order elliptic operators. The coupled formulation is implemented and its convergence properties are established numerically by using manufactured solutions. The influence of the tau parameter on the coupled formulation is studied., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Artículo científico (JournalArticle)

A Cº interior penalty method for 4th order PDEs

  • Fojo, Dani
  • Codony Gisbert, David|||0000-0002-7341-9799
  • Fernández Méndez, Sonia|||0000-0002-9305-7684
A method to solve 4th-order PDEs using the Finite Element Method (FEM) with standard C0 elements is derived and studied. It is based on a special weak form accounting for the discontinuous derivatives of the approximation and imposing their normal continuity across element sides in weak form. The method is developed for the equations of the deformation of a Kirchoff plate, but its extension to other 4th-order PDEs is expected to be straight-forward. The accuracy and convergence of the resulting numerical approximation is studied with numerical experiments., This work was supported by the EuropeanResearch Council (StG-679451 to IreneArias) and the Generalitat de Catalunya (2017-SGR-1278)., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Artículo científico (JournalArticle)

A C0 interior penalty Finite Element Method for flexoelectricity

  • Ventura, Jordi
  • Codony Gisbert, David|||0000-0002-7341-9799
  • Fernández Méndez, Sonia|||0000-0002-9305-7684
This is a post-peer-review, pre-copyedit version of an article published in Journal of scientific computing. The final authenticated version is available online at: http://dx.doi.org/10.1007/s10915-021-01613-w, We propose a C0 Interior Penalty Method (C0-IPM) for the computational modelling of flexoelectricity, with application also to strain gradient elasticity, as a simplified case. Standard high-order C0 finite element approximations, with nodal basis, are considered. The proposed C0-IPM formulation involves second derivatives in the interior of the elements, plus integrals on the mesh faces (sides in 2D), that impose C1 continuity of the displacement in weak form. The formulation is stable for large enough interior penalty parameter, which can be estimated solving an eigenvalue problem. The applicability and convergence of the method is demonstrated with 2D and 3D numerical examples., This work was supported by the European Research Council (StG679451 to Irene Arias), Agencia Estatal de Investigaci´on (RTI2018-101662-B-I00), Ministerio de Econom´ıa y Competitividad (CEX2018-000797-S) and Generalitat de Catalunya (2017- SGR-1278), Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Artículo científico (JournalArticle)

Weak enforcement of interface continuity and generalized periodicity in high-order electromechanical problems

  • Barceló Mercader, Jordi
  • Codony Gisbert, David|||0000-0002-7341-9799
  • Fernández Méndez, Sonia|||0000-0002-9305-7684
  • Arias Vicente, Irene|||0000-0002-6761-3499
This is the peer reviewed version of the following article: Barcelo, J. [et al.]. Weak enforcement of interface continuity and generalized periodicity in high-order electromechanical problems. "International journal for numerical methods in engineering", 28 Febrer 2022, vol. 123, núm. 4, p. 901-923, which has been published in final form at DOI10.1002/nme.6882. This article may be used for non-commercial purposes in accordance with Wiley Terms and Conditions for Self-Archiving., We present a formulation for the weak enforcement of continuity conditions atmaterialinterfacesinhigh-orderproblemsbymeansofNitsche’smethod,whichis particularly suited for unfitted discretizations. This formulation is extendedto impose generalized periodicity conditions at the unit cell boundaries of peri-odic structures. The formulation is derived for flexoelectricity, a high-orderelectromechanical coupling between strain gradient and electric field, mathe-matically modeled as a coupled system of fourth-order PDEs. The design of flex-oelectricdevicesrequiresthesolutionofhigh-orderboundaryvalueproblemsoncomplex material architectures, including general multimaterial arrangements.ThiscanbeefficientlyachievedwithanimmersedboundaryB-splinesapproach.Furthermore, the design of flexoelectric metamaterials also involves the anal-ysis of periodic unit cells with generalized periodicity conditions. Optimalhigh-order convergence rates are obtained with an unfitted B-spline approxi-mation, confirming the reliability of the method. The numerical simulationsillustrate the usefulness of the proposed approach toward the design of func-tional electromechanical multimaterial devices and metamaterials harnessingthe flexoelectric effect., Departament d'Universitats, Recerca i Societat de la Informació, 2017-SGR-1278; ICREA Academia; H2020 European Research Council, StG-679451; Secretaría de Estado de Investigación, Desarrollo e Innovación, CEX2018-000797-S; RTI2018-101662-B-I00., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Artículo científico (JournalArticle)

Converse flexoelectricity yields large piezoresponse force microscopy signals in non-piezoelectric materials

  • Abdollahi Hosnijeh, Amir|||0000-0003-0363-4984
  • Domingo, Neus
  • Arias Vicente, Irene|||0000-0002-6761-3499
  • Catalan, Gustau
Converse flexoelectricity is a mechanical stress induced by an electric polarization gradient. It can appear in any material, irrespective of symmetry, whenever there is an inhomogeneous electric field distribution. This situation invariably happens in piezoresponse force microscopy (PFM), which is a technique whereby a voltage is delivered to the tip of an atomic force microscope in order to stimulate and probe piezoelectricity at the nanoscale. While PFM is the premier technique for studying ferroelectricity and piezoelectricity at the nanoscale, here we show, theoretically and experimentally, that large effective piezoelectric coefficients can be measured in non-piezoelectric dielectrics due to converse flexoelectricity., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Artículo científico (JournalArticle)

Flexoelectricity causes surface piezoelectric-like effects in dielectrics

  • Mohammadi, Hossein|||0000-0003-2716-9028
  • Greco, Francesco|||0000-0001-6126-493X
  • Codony Gisbert, David|||0000-0002-7341-9799
  • Arias Vicente, Irene|||0000-0002-6761-3499
In this paper, we study the surface effects that bulk flexoelectric models exhibit in finite samples. We first show that flexoelectric materials do not exhibit electromechanical response under homogeneous loading when the body is infinite. However, when the size of the body is finite, due to the symmetry-breaking nature of surfaces, homogeneous loading (mechanical or electrical) can cause an electromechanical response near the surfaces. We obtain closed-form solutions for finite samples under different electromechanical loading conditions and show that the electromechanical response caused by the bulk flexoelectric effect is reminiscent of surface piezoelectricity, causing boundary layers in certain components of the strains and/or electric fields near the free surfaces., This work was supported by the Generalitat de Catalunya (“ICREA Academia” award for excellence in research to I.A., and Grants No. 2017-SGR-1278 and 2021-SGR-01049), the European Research Council (StG-679451 to I.A.), and the Spanish Ministry of Economy and Competitiveness (Grant PID2023-152533OB-I00 funded by MICIU/AEI/10.13039/501100011033/ERDF/EU, and Grant RTI2018-101662-B-I00). D.C. acknowledges the support of the Spanish Ministry of Universities through the Margarita Salas fellowship (European Union - NextGenerationEU). H.M. received the support of a fellowship from “la Caixa” Foundation (ID 100010434). The fellowship code is LCF/BQ/DI20/11780036. CIMNE is recipient of a Severo Ochoa Award of Excellence from the MINECO., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Artículo científico (JournalArticle)

Continuum and computational modeling of surface effects in flexoelectric materials

  • Dingle Palmer, Mònica|||0000-0002-8137-6469
  • Arias Vicente, Irene|||0000-0002-6761-3499
  • Codony Gisbert, David|||0000-0002-7341-9799
In recent times, with the rise of nanoscale technologies, miniaturization of devices has prompted the need to study electromechanical phenomena at small scales. Most studies focus on the phenomena occurring at the bulk portion of the material, such as flexoelectricity, but neglect the effects that arise from the surfaces of the samples. Given the fact that, at such scales, surface-to-volume ratio is inherently large, surface effects cannot be ignored if the full and accurate description of the material’s response wants to be provided. In this work, we present a model that successfully integrates flexoelectricity and the effects of surfaces, and we properly derive the governing equations and boundary conditions for the boundary value problem. We also present a numerical approach in order to computationally solve it, converging at high-order optimal rates. In addition, we present an analytical 1D Euler–Bernoulli electromechanical beam model. Numerically, we find the presence of boundary layers in the transversal electric field across the beam thickness, which are not accounted for in the analytical 1D model. Finally, we find numerical solutions for geometrically-polarized flexoelectric lattice metamaterials, which have large area-to-volume ratios, giving rise to very relevant surface effects. This work emphasizes the importance of accounting for surface effects in modeling and design of flexoelectric devices, including geometrically-polarized metamaterials., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Artículo científico (JournalArticle)

Transversal flexoelectric coefficient for nanostructures at finite deformations from first principles

  • Codony Gisbert, David|||0000-0002-7341-9799
  • Arias Vicente, Irene|||0000-0002-6761-3499
  • Suryanarayana, Phanish
We present a novel formulation for calculating the transversal flexoelectric coefficient of nanostructures at finite deformations from first principles. Specifically, we introduce the concept of radial polarization to make the coefficient a well-defined quantity for uniform bending deformations. We use the framework to calculate the flexoelectric coefficient for group IV atomic monolayers using density functional theory. We find that graphene’s coefficient is significantly larger than previously reported, with a charge transfer mechanism that differs from other members of its group., This work was supported in part by the Generalitat de Catalunya (ICREA Academia award for excellence in research to I.A. and Grant No. 2017-SGR-1278) and the European Research Council (StG-679451 to I.A.). I.A. acknowledges financial support from the Spanish Ministry of Economy and Competitiveness, through the “Severo Ochoa Programme for Centres of Excellence in R&D” (CEX2018- 000797-S). P.S. gratefully acknowledges the support of the U.S. National Science Foundation (CAREER-1553212). The authors acknowledge discussions with Shashikant Kumar and his help with some simulations. P.S. acknowledges discussions with Amartya Banerjee prior to starting this work. The authors also acknowledge the valuable comments of the anonymous referees., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Artículo científico (JournalArticle)

Topology optimization of flexoelectric metamaterials with apparent piezoelectricity

  • Greco, Francesco|||0000-0001-6126-493X
  • Codony Gisbert, David|||0000-0002-7341-9799
  • Mohammadi, Hossein|||0000-0003-2716-9028
  • Fernández Méndez, Sonia|||0000-0002-9305-7684
  • Arias Vicente, Irene|||0000-0002-6761-3499
The flexoelectric effect, coupling polarization and strain gradient as well as strain and electric field gradients, is universal to dielectrics, but, as compared to piezoelectricity, it is more difficult to harness as it requires field gradients and it is a small-scale effect. This drawback can be overcome by suitably designing multiscale metamaterials made of a non-piezoelectric base material but exhibiting apparent piezoelectricity. We develop a theoretical and computational framework to perform topology optimization of the representative volume element of such metamaterials by accurately modeling the governing equations of flexoelectricity using a Cartesian B-spline method, describing geometry with a level set, and resorting to genetic algorithms for optimization. We consider a multi-objective optimization problem where area fraction competes with each one of the four fundamental piezoelectric functionalities (stress/strain sensor/actuator). We computationally obtain Pareto fronts, and discuss the different geometries depending on the apparent piezoelectric coefficient being optimized. Our results show that optimal material architectures strongly depend on the specific functional property being optimized, and that, except for stress actuators, optimal structures are low-area-fraction lattices. In general, we find competitive estimations of apparent piezoelectricity as compared to reference materials such as quartz and PZT ceramics. This opens the possibility to design devices for sensing, actuation and energy harvesting from a much wider, cheaper and effective class of materials., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Artículo científico (JournalArticle)

An immersed boundary hierarchical B-spline method for flexoelectricity

  • Codony Gisbert, David|||0000-0002-7341-9799
  • Marco Alacid, Onofre
  • Fernández Méndez, Sonia|||0000-0002-9305-7684
  • Arias Vicente, Irene|||0000-0002-6761-3499
© 2019. This manuscript version is made available under the CC-BY-NC-ND 4.0 license http://creativecommons.org/licenses/by-nc-nd/4.0/, This paper develops a computational framework with unfitted meshes to solve linear piezoelectricity and flexoelectricity electromechanical boundary value problems including strain gradient elasticity at infinitesimal strains. The high-order nature of the coupled PDE system is addressed by a sufficiently smooth hierarchical B-spline approximation on a background Cartesian mesh. The domain of interest is embedded into the background mesh and discretized in an unfitted fashion. The immersed boundary approach allows us to use B-splines on arbitrary domain shapes, regardless of their geometrical complexity, and could be directly extended, for instance, to shape and topology optimization. The domain boundary is represented by NURBS, and exactly integrated by means of the NEFEM mapping. Local adaptivity is achieved by hierarchical refinement of B-spline basis, which are efficiently evaluated and integrated thanks to their piecewise polynomial definition. Nitsche's formulation is derived to weakly enforce essential boundary conditions, accounting also for the non-local conditions on the non-smooth portions of the domain boundary (i.e. edges in 3D or corners in 2D) arising from Mindlin's strain gradient elasticity theory. Boundary conditions modeling sensing electrodes are formulated and enforced following the same approach. Optimal error convergence rates are reported using high-order B-spline approximations. The method is verified against available analytical solutions and well-known benchmarks from the literature., Peer Reviewed
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Weak enforcement of interface continuity and generalized periodicity in high-order electromechanical problems

  • Barceló Mercader, Jordi
  • Codony Gisbert, David
  • Fernández Méndez, Sonia
  • Arias Vicente, Irene
This is the peer reviewed version of the following article: Barcelo, J. [et al.]. Weak enforcement of interface continuity and generalized periodicity in high-order electromechanical problems. "International journal for numerical methods in engineering", 28 Febrer 2022, vol. 123, núm. 4, p. 901-923, which has been published in final form at DOI10.1002/nme.6882. This article may be used for non-commercial purposes in accordance with Wiley Terms and Conditions for Self-Archiving., We present a formulation for the weak enforcement of continuity conditions atmaterialinterfacesinhigh-orderproblemsbymeansofNitsche’smethod,whichis particularly suited for unfitted discretizations. This formulation is extendedto impose generalized periodicity conditions at the unit cell boundaries of peri-odic structures. The formulation is derived for flexoelectricity, a high-orderelectromechanical coupling between strain gradient and electric field, mathe-matically modeled as a coupled system of fourth-order PDEs. The design of flex-oelectricdevicesrequiresthesolutionofhigh-orderboundaryvalueproblemsoncomplex material architectures, including general multimaterial arrangements.ThiscanbeefficientlyachievedwithanimmersedboundaryB-splinesapproach.Furthermore, the design of flexoelectric metamaterials also involves the anal-ysis of periodic unit cells with generalized periodicity conditions. Optimalhigh-order convergence rates are obtained with an unfitted B-spline approxi-mation, confirming the reliability of the method. The numerical simulationsillustrate the usefulness of the proposed approach toward the design of func-tional electromechanical multimaterial devices and metamaterials harnessingthe flexoelectric effect., Departament d'Universitats, Recerca i Societat de la Informació, 2017-SGR-1278; ICREA Academia; H2020 European Research Council, StG-679451; Secretaría de Estado de Investigación, Desarrollo e Innovación, CEX2018-000797-S; RTI2018-101662-B-I00., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

A Cº interior penalty method for 4th order PDEs

  • Fojo, Dani
  • Codony Gisbert, David
  • Fernández Méndez, Sonia
A method to solve 4th-order PDEs using the Finite Element Method (FEM) with standard C0 elements is derived and studied. It is based on a special weak form accounting for the discontinuous derivatives of the approximation and imposing their normal continuity across element sides in weak form. The method is developed for the equations of the deformation of a Kirchoff plate, but its extension to other 4th-order PDEs is expected to be straight-forward. The accuracy and convergence of the resulting numerical approximation is studied with numerical experiments., This work was supported by the EuropeanResearch Council (StG-679451 to IreneArias) and the Generalitat de Catalunya (2017-SGR-1278)., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Flexoelectricity causes surface piezoelectric-like effects in dielectrics

  • Mohammadi, Hossein
  • Greco, Francesco
  • Codony Gisbert, David
  • Arias Vicente, Irene
In this paper, we study the surface effects that bulk flexoelectric models exhibit in finite samples. We first show that flexoelectric materials do not exhibit electromechanical response under homogeneous loading when the body is infinite. However, when the size of the body is finite, due to the symmetry-breaking nature of surfaces, homogeneous loading (mechanical or electrical) can cause an electromechanical response near the surfaces. We obtain closed-form solutions for finite samples under different electromechanical loading conditions and show that the electromechanical response caused by the bulk flexoelectric effect is reminiscent of surface piezoelectricity, causing boundary layers in certain components of the strains and/or electric fields near the free surfaces., This work was supported by the Generalitat de Catalunya (“ICREA Academia” award for excellence in research to I.A., and Grants No. 2017-SGR-1278 and 2021-SGR-01049), the European Research Council (StG-679451 to I.A.), and the Spanish Ministry of Economy and Competitiveness (Grant PID2023-152533OB-I00 funded by MICIU/AEI/10.13039/501100011033/ERDF/EU, and Grant RTI2018-101662-B-I00). D.C. acknowledges the support of the Spanish Ministry of Universities through the Margarita Salas fellowship (European Union - NextGenerationEU). H.M. received the support of a fellowship from “la Caixa” Foundation (ID 100010434). The fellowship code is LCF/BQ/DI20/11780036. CIMNE is recipient of a Severo Ochoa Award of Excellence from the MINECO., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Converse flexoelectricity yields large piezoresponse force microscopy signals in non-piezoelectric materials

  • Abdollahi Hosnijeh, Amir
  • Domingo, Neus
  • Arias Vicente, Irene
  • Catalan, Gustau
Converse flexoelectricity is a mechanical stress induced by an electric polarization gradient. It can appear in any material, irrespective of symmetry, whenever there is an inhomogeneous electric field distribution. This situation invariably happens in piezoresponse force microscopy (PFM), which is a technique whereby a voltage is delivered to the tip of an atomic force microscope in order to stimulate and probe piezoelectricity at the nanoscale. While PFM is the premier technique for studying ferroelectricity and piezoelectricity at the nanoscale, here we show, theoretically and experimentally, that large effective piezoelectric coefficients can be measured in non-piezoelectric dielectrics due to converse flexoelectricity., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Topology optimization of flexoelectric metamaterials with apparent piezoelectricity

  • Greco, Francesco
  • Codony Gisbert, David
  • Mohammadi, Hossein
  • Fernández Méndez, Sonia
  • Arias Vicente, Irene
The flexoelectric effect, coupling polarization and strain gradient as well as strain and electric field gradients, is universal to dielectrics, but, as compared to piezoelectricity, it is more difficult to harness as it requires field gradients and it is a small-scale effect. This drawback can be overcome by suitably designing multiscale metamaterials made of a non-piezoelectric base material but exhibiting apparent piezoelectricity. We develop a theoretical and computational framework to perform topology optimization of the representative volume element of such metamaterials by accurately modeling the governing equations of flexoelectricity using a Cartesian B-spline method, describing geometry with a level set, and resorting to genetic algorithms for optimization. We consider a multi-objective optimization problem where area fraction competes with each one of the four fundamental piezoelectric functionalities (stress/strain sensor/actuator). We computationally obtain Pareto fronts, and discuss the different geometries depending on the apparent piezoelectric coefficient being optimized. Our results show that optimal material architectures strongly depend on the specific functional property being optimized, and that, except for stress actuators, optimal structures are low-area-fraction lattices. In general, we find competitive estimations of apparent piezoelectricity as compared to reference materials such as quartz and PZT ceramics. This opens the possibility to design devices for sensing, actuation and energy harvesting from a much wider, cheaper and effective class of materials., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Continuum and computational modeling of surface effects in flexoelectric materials

  • Dingle Palmer, Mònica
  • Arias Vicente, Irene
  • Codony Gisbert, David
In recent times, with the rise of nanoscale technologies, miniaturization of devices has prompted the need to study electromechanical phenomena at small scales. Most studies focus on the phenomena occurring at the bulk portion of the material, such as flexoelectricity, but neglect the effects that arise from the surfaces of the samples. Given the fact that, at such scales, surface-to-volume ratio is inherently large, surface effects cannot be ignored if the full and accurate description of the material’s response wants to be provided. In this work, we present a model that successfully integrates flexoelectricity and the effects of surfaces, and we properly derive the governing equations and boundary conditions for the boundary value problem. We also present a numerical approach in order to computationally solve it, converging at high-order optimal rates. In addition, we present an analytical 1D Euler–Bernoulli electromechanical beam model. Numerically, we find the presence of boundary layers in the transversal electric field across the beam thickness, which are not accounted for in the analytical 1D model. Finally, we find numerical solutions for geometrically-polarized flexoelectric lattice metamaterials, which have large area-to-volume ratios, giving rise to very relevant surface effects. This work emphasizes the importance of accounting for surface effects in modeling and design of flexoelectric devices, including geometrically-polarized metamaterials., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

A C0 interior penalty Finite Element Method for flexoelectricity

  • Ventura, Jordi
  • Codony Gisbert, David
  • Fernández Méndez, Sonia
This is a post-peer-review, pre-copyedit version of an article published in Journal of scientific computing. The final authenticated version is available online at: http://dx.doi.org/10.1007/s10915-021-01613-w, We propose a C0 Interior Penalty Method (C0-IPM) for the computational modelling of flexoelectricity, with application also to strain gradient elasticity, as a simplified case. Standard high-order C0 finite element approximations, with nodal basis, are considered. The proposed C0-IPM formulation involves second derivatives in the interior of the elements, plus integrals on the mesh faces (sides in 2D), that impose C1 continuity of the displacement in weak form. The formulation is stable for large enough interior penalty parameter, which can be estimated solving an eigenvalue problem. The applicability and convergence of the method is demonstrated with 2D and 3D numerical examples., This work was supported by the European Research Council (StG679451 to Irene Arias), Agencia Estatal de Investigaci´on (RTI2018-101662-B-I00), Ministerio de Econom´ıa y Competitividad (CEX2018-000797-S) and Generalitat de Catalunya (2017- SGR-1278), Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publication Contribución de congreso (ConferenceOutput)

Coupling of continuous and HDG methods

  • Paipuri, Mahendra
  • Tiago, Carlos
  • Fernández Méndez, Sonia
A coupling strategy between hybridizable discontinuous Galerkin (HDG) and continuous Galerkin (CG) methods is proposed in the framework of second-order elliptic operators. The coupled formulation is implemented and its convergence properties are established numerically by using manufactured solutions. The influence of the tau parameter on the coupled formulation is studied., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

An immersed boundary hierarchical B-spline method for flexoelectricity

  • Codony Gisbert, David
  • Marco Alacid, Onofre
  • Fernández Méndez, Sonia
  • Arias Vicente, Irene
© 2019. This manuscript version is made available under the CC-BY-NC-ND 4.0 license http://creativecommons.org/licenses/by-nc-nd/4.0/, This paper develops a computational framework with unfitted meshes to solve linear piezoelectricity and flexoelectricity electromechanical boundary value problems including strain gradient elasticity at infinitesimal strains. The high-order nature of the coupled PDE system is addressed by a sufficiently smooth hierarchical B-spline approximation on a background Cartesian mesh. The domain of interest is embedded into the background mesh and discretized in an unfitted fashion. The immersed boundary approach allows us to use B-splines on arbitrary domain shapes, regardless of their geometrical complexity, and could be directly extended, for instance, to shape and topology optimization. The domain boundary is represented by NURBS, and exactly integrated by means of the NEFEM mapping. Local adaptivity is achieved by hierarchical refinement of B-spline basis, which are efficiently evaluated and integrated thanks to their piecewise polynomial definition. Nitsche's formulation is derived to weakly enforce essential boundary conditions, accounting also for the non-local conditions on the non-smooth portions of the domain boundary (i.e. edges in 3D or corners in 2D) arising from Mindlin's strain gradient elasticity theory. Boundary conditions modeling sensing electrodes are formulated and enforced following the same approach. Optimal error convergence rates are reported using high-order B-spline approximations. The method is verified against available analytical solutions and well-known benchmarks from the literature., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Transversal flexoelectric coefficient for nanostructures at finite deformations from first principles

  • Codony Gisbert, David
  • Arias Vicente, Irene
  • Suryanarayana, Phanish
We present a novel formulation for calculating the transversal flexoelectric coefficient of nanostructures at finite deformations from first principles. Specifically, we introduce the concept of radial polarization to make the coefficient a well-defined quantity for uniform bending deformations. We use the framework to calculate the flexoelectric coefficient for group IV atomic monolayers using density functional theory. We find that graphene’s coefficient is significantly larger than previously reported, with a charge transfer mechanism that differs from other members of its group., This work was supported in part by the Generalitat de Catalunya (ICREA Academia award for excellence in research to I.A. and Grant No. 2017-SGR-1278) and the European Research Council (StG-679451 to I.A.). I.A. acknowledges financial support from the Spanish Ministry of Economy and Competitiveness, through the “Severo Ochoa Programme for Centres of Excellence in R&D” (CEX2018- 000797-S). P.S. gratefully acknowledges the support of the U.S. National Science Foundation (CAREER-1553212). The authors acknowledge discussions with Shashikant Kumar and his help with some simulations. P.S. acknowledges discussions with Amartya Banerjee prior to starting this work. The authors also acknowledge the valuable comments of the anonymous referees., Peer Reviewed, Postprint (author's final draft)
Dipòsit Digital de Documents de la UAB
Publication Artículo científico (JournalArticle)

Converse flexoelectricity yields large piezoresponse force microscopy signals in non-piezoelectric materials

  • Abdollahi, Amir|||0000-0003-0363-4984
  • Domingo Marimon, Neus|||0000-0002-5229-6638
  • Arias, Irene|||0000-0002-6761-3499
  • Catalan, Gustau|||0000-0003-0214-4828
Converse flexoelectricity is a mechanical stress induced by an electric polarization gradient. It can appear in any material, irrespective of symmetry, whenever there is an inhomogeneous electric field distribution. This situation invariably happens in piezoresponse force microscopy (PFM), which is a technique whereby a voltage is delivered to the tip of an atomic force microscope in order to stimulate and probe piezoelectricity at the nanoscale. While PFM is the premier technique for studying ferroelectricity and piezoelectricity at the nanoscale, here we show, theoretically and experimentally, that large effective piezoelectric coefficients can be measured in non-piezoelectric dielectrics due to converse flexoelectricity.
Dipòsit Digital de Documents de la UAB
Publication Artículo científico (JournalArticle)

The emancipation of flexoelectricity

  • Arias, Irene|||0000-0002-6761-3499
  • Catalan, Gustau|||0000-0003-0214-4828
  • Sharma, Pradeep
Consider the following: writing (and reading) ferroelectric memories without applying voltage;1-3 piezoelectric-like transduction without piezoelectric materials;4-6 bone remodeling7 and mammalian hearing;8,9 asymmetric fracture toughness;10 and bulk photovoltaic effects in non-polar materials.11 What do these apparently disparate phenomena have in common? Flexoelectricity...
Dipòsit Digital de Documents de la UAB
Publication Artículo científico (JournalArticle)

Switchable tribology of ferroelectrics

  • Cho, Seongwoo|||0000-0002-3000-4251
  • Gaponenko, Iaroslav|||0000-0002-9694-7033
  • Cordero Edwards, Kumara|||0000-0003-3721-7863
  • Barceló-Mercader, Jordi
  • Arias, Irene|||0000-0002-6761-3499
  • Kim, Daeho
  • Lichtensteiger, Céline|||0000-0002-9796-8071
  • Yeom, Jiwon
  • Musy, Loïc|||0000-0002-7741-6763
  • Kim, Hyunji
  • Han, Seung Min
  • Catalan, Gustau|||0000-0003-0214-4828
  • Paruch, Patrycja
  • Hong, Seungbum|||0000-0002-2667-1983
Switchable tribological properties of ferroelectrics offer an alternative route to visualize and control ferroelectric domains. Here, we observe the switchable friction and wear behavior of ferroelectrics using a nanoscale scanning probe-down domains have lower friction coefficients and show slower wear rates than up domains and can be used as smart masks. This asymmetry is enabled by flexoelectrically coupled polarization in the up and down domains under a sufficiently high contact force. Moreover, we determine that this polarization-sensitive tribological asymmetry is widely applicable across various ferroelectrics with different chemical compositions and crystalline symmetry. Finally, using this switchable tribology and multi-pass patterning with a domain-based dynamic smart mask, we demonstrate three-dimensional nanostructuring exploiting the asymmetric wear rates of up and down domains, which can, furthermore, be scaled up to technologically relevant (mm-cm) size. These findings demonstrate that ferroelectrics are electrically tunable tribological materials at the nanoscale for versatile applications.