Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 25
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Nanostructured Ti thin films by magnetron sputtering at oblique angles

  • Álvarez, Rafael
  • García-Martín, José Miguel
  • García-Valenzuela, Aurelio
  • Macías-Montero, M.
  • Ferrer, F. J.
  • Santiso, José
  • Cotrino, José
  • Rico, Víctor J.
  • González-Elipe, Agustín R.
  • Palmero, Alberto
The growth of Ti thin films by the magnetron sputtering technique at oblique angles and at room temperature is analysed from both experimental and theoretical points of view. Unlike other materials deposited in similar conditions, the nanostructure development of the Ti layers exhibits an anomalous behaviour when varying both the angle of incidence of the deposition flux and the deposition pressure. At low pressures, a sharp transition from compact to isolated, vertically aligned, nanocolumns is obtained when the angle of incidence surpasses a critical threshold. Remarkably, this transition also occurs when solely increasing the deposition pressure under certain conditions. By the characterization of the Ti layers, the realization of fundamental experiments and the use of a simple growth model, we demonstrate that surface mobilization processes associated to a highly directed momentum distribution and the relatively high kinetic energy of sputtered atoms are responsible for this behaviour, The authors thank Fundación Domingo Martínez, the Junta de Andalucía (P12-FQM-2265) and the Ministry of Science and Innovation (Projects CONSOLIDER CSD2008-00023, MAT2013-42900-P, MAT2013-40852-R, MAT2014-59772- C2-1, MAT2011-29081) for financial support., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Low-cost and large-size nanoplasmonic sensor based on Fano resonances with fast response and high sensitivity

  • Baquedano, Estela
  • González Sagardoy, María Ujué
  • Paniagua-Domínguez, R.
  • Sánchez-Gil, José A.
  • Postigo, Pablo Aitor
10 pags., 4 figs. -- OCIS codes: (130.6010) Sensors; (240.6680) Surface plasmons; (250.5403) Plasmonics; (350.2770) Gratings., We have developed a low-cost, fast and sensitive plasmonic sensor with a large-size for easy handling. The sensor is formed by a Au nanobelt grating fabricated by soft lithography with a period of 780 nm and a width of 355 nm in an even and uniform area of ~2 × 2 cm2. The sensor uses the Fano-shaped third order mode localized plasmon resonance of the Au nanobelts, which appears in the visible part of the transmission spectrum. We have found a detection resolution of 1.56 × 10¿5 refractive index units with a temporal resolution of 1 s in a sensing area of 0.75 × 0.75 mm2. The high uniformity and size of the sensor permit the detection using a simple optical system, which provides the device with the potential to be used as an easy to handle, portable and disposable sensor., Spanish MINEICO (FIS2015-69295-C3-2-P, MAT2014-59772-C2-1, TEC2014-54449-C3-3 and PCIN-2013-179)., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Contribución de congreso (ConferenceOutput)

Magnetic structure of nanometer scale magnetic antidot arrays

  • Kaidatzis, Andreas
  • Pérez del Real, Rafael
  • Béron, Fanny
  • Palma, Juan Luis
  • Álvaro Bruna, Raquel
  • Palmero, Ester M.
  • Velo, Murilo F.
  • Arzuza, Luis C. C.
  • Niarchos, Dimitrios
  • Vázquez Villalabeitia, Manuel
  • Pirota, K. R.
  • Escrig, Juan
  • García-Martín, José Miguel
Trabajo presentado en la conferencia Fuerzas y Túnel (FyT2016), celebrada en Girona del 5 al 7 de septiembre de 2016., Magnetic antidot arrays are groups of ordered holes patterned on a continuous magnetic film. They can be used as magnonic crystals with potential application in microwave devices [1], for magnetically-active plasmonics [2], and for biosensing applications [3]. We have followed two different routes to obtain magnetic antidots on Co, Permalloy (Py), and Co/Py films with different characteristics. Focused ion beam allowed obtaining hexagonal or square lattice antidot arrays with long-range order (hole diameter d=55nm, periodicity p=150-300nm) [4], whereas oblique deposition onto nanoporous alumina templates was used to obtain arrays with only hexagonal short-range order (d=40nm, p=105nm) [5]. The arrays were studied by magneto-optic Kerr effect, magnetic force microscopy (MFM) and micromagnetic simulations. It is shown how the coercivity increases with the density of antidots and the magnetic anisotropy axes strongly depend on the array symmetry. The MFM images show the magnetic structure of the arrays to be commensurate to their morphology, with domain walls (DW) pinned by the holes and in some cases super-DW separating linear domains (see Fig.)., Funding from CSIC (i-Link0783), MINECO (MAT2014-59772-C2-1), Comunidad de Madrid (Nanofrontmag), FAPESP (Brazil), Basal and Fondecyt (Chile) and EU (318144 and 272470)., No
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Synergic antibacterial coatings combining titanium nanocolumns and tellurium nanorods

  • Medina Cruz, David
  • González Sagardoy, María Ujué
  • Tien-Street, William
  • Fernández Castro, Marcial
  • Vernet Crua, Ada
  • Fernández-Martínez, Iván
  • Martínez Orellana, Lidia
  • Huttel, Yves
  • Webster, Thomas J.
  • García-Martín, José Miguel
Anocolumnar titanium coatings have been fabricated in two sputtering systems with very different characteristics (a laboratory setup and semi-industrial equipment), thus possessing different morphologies (150 nm long columns tilted 20° from the normal and 300 nm long ones tilted 40°, respectively). These coatings exhibit similar antibacterial properties against Gram positive (Staphylococcus aureus) and Gram negative (Escherichia coli) bacteria. When a synergic route is followed and these coatings are functionalized with tellurium (Te) nanorods, the antibacterial properties are enhanced, especially for the long nanocolumns case. The biocompatibility is preserved in all the nanostructured coatings., Funding from MINECO (MAT2014-59772-C2-1-P, MAT2014-59772-C2-2-P and MAT2011-29194-C02-02) and Fundación Domingo Martínez is acknowledged. J.M. G.-M. thanks MECD (PRX16/00383) and Fulbright Commission for his stay at Northeastern University. We also acknowledge the service from the MiNa Laboratory at IMN funded by CM (S2013/ICE2822), MINECO (CSIC13-4E-1794) and the EU (FEDER, FSE)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Tuning the size, composition and structure of Au and Co50Au50 nanoparticles by high-power impulse magnetron sputtering in gas-phase synthesis

  • Mayoral, Álvaro
  • Martínez Orellana, Lidia
  • García-Martín, José Miguel
  • Fernández-Martínez, I.
  • García-Hernández, Mar
  • Galiana, Beatriz
  • Ballesteros Pérez, Carmen Inés
  • Huttel, Yves
Gas-phase synthesis of nanoparticles with different structural and chemical distribution is reported using a circular magnetron sputtering in an ion cluster source by applying high-power impulses. The influence of the pulse characteristics on the final deposit was evaluated on Au nanoparticles. The results have been compared with the more common direct current approach. In addition, it is shown for the first time that high-power impulses in magnetron based gas aggregation sources allows the growth of binary nanoparticles, CoAu in this case, with a variety of crystalline and chemical arrangements which are analyzed at the atomic level., This work was supported by the EU agreement No. 696656 (GrapheneCore1-Graphene-based disruptive technologies), Spanish Ministerio de Economía, Industria y Competitividad under project MAT2014-59772-C2-1-P, Spanish Ministerio de Economía, Industria y Competitividad under project MAT2014-59772-C2-2-P, Spanish Ministerio de Economía, Industria y Competitividad under project MAT2016-80394-R, ERC-2013-SyG 610256 NANOCOSMOS., National Science Foundation of China (21850410448), Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Magnetic properties of Fe3O4 antidot arrays synthesized by AFIR: atomic layer deposition, focused ion beam and thermal reduction

  • Palma, Juan Luis
  • Pereira, A.
  • Álvaro Bruna, Raquel
  • García-Martín, José Miguel
  • Escrig, Juan
Magnetic films of magnetite (Fe3O4) with controlled defects, so-called antidot arrays, were synthesized by a new technique called AFIR. AFIR consists of the deposition of a thin film by atomic layer deposition, the generation of square and hexagonal arrays of holes using focused ion beam milling, and the subsequent thermal reduction of the antidot arrays. Magnetic characterizations were carried out by magneto-optic Kerr effect measurements, showing the enhancement of the coercivity for the antidot arrays. AFIR opens a new route to manufacture ordered antidot arrays of magnetic oxides with variable lattice parameters., he authors acknowledge financial support from Fondequip (refs. EQM120045 and EQM140092), from Fondecyt (ref. 1150952, 11150671 and 11171045), from POSTDOC_DICYT 041831EM POSTDOC, from the Spanish MINECO (ref. MAT2014-59772-C2-1-P) and from the Basal Project (ref. FB0807). We also acknowledge the service from the MiNa Laboratory at IMN funded by CM (S2013/ICE2822), MINECO (CSIC13-4E-1794) and EU (FEDER, FSE)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Au and Ag sputter deposition on printer paper

  • Kaidatzis, Andreas
  • Psycharis, V.
  • González Sagardoy, María Ujué
  • García-Martín, José Miguel
  • Niarchos, Dimitrios
We study metal-coated paper for low cost sensor applications. Sputter deposition is used to coat commercially available stationary printer paper with Au or Ag thin films. Two kinds of substrates are used: copy paper and glossy photo paper. The surface morphology, coating structure and electrical resistivity of the samples is studied. We find that after deposition of a nominally 100 nm thick metal layer the templates retain their initial morphology, which is fibre-like at the copy paper and flake-like at the photo paper. The metal-coated paper is conductive in both cases, with resistivity a few times higher than the bulk value. The photo paper samples have lower resistivity than the copy paper ones. Moreover, no observable resistivity variation is observed after 8 weeks of room temperature storage in a desiccator., Funding from the E.C. through a FP7-ICT project (Grant No. 318144) and MINECO (ref.: MAT2014-59772-C2-1-P) is acknowledged., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Nanometer scale hard/soft bilayer magnetic antidots

  • Béron, Fanny
  • Kaidatzis, Andreas
  • Velo, Murilo F.
  • Arzuza, Luis C. C.
  • Palmero, Ester M.
  • Real, Rafael P. del
  • Niarchos, Dimitrios
  • Pirota, K. R.
  • García-Martín, José Miguel
The effect of arrays of nanometer scale pores on the magnetic properties of thin films has been analyzed. Particularly, we investigated the influence of the out-of-plane magnetization component created by the nanopores on the in-plane magnetic behavior of patterned hard/soft magnetic thin films in antidot morphology. Its influence on the coupling in Co/Py bilayers of few tens of nanometer thick is compared for disordered and ordered antidots of 35-nm diameter. The combination of magneto-optical Kerr effect (MOKE) and first-order reversal curve (FORC) technique allows probing the effects of the induced perpendicular magnetization component on the bilayer magnetic behavior, while magnetic force microscopy (MFM) is used to image it. We found that ordered antidots yield a stronger out-of-plane component than disordered ones, influencing in a similar manner the hard layer global in-plane magnetic behavior if with a thin or without soft layer. However, its influence changes with a thicker soft layer, which may be an indication of a weaker coupling, This work was financially supported by the i-Link project “Magnetic antidots,” funded by Consejo Superior de Investigaciones Científicas (CSIC, Spain) and Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP, Brazil). We also acknowledge additional funding from Spain, through MINECO (ref.: MAT2014-59772-C2-1-P), Comunidad de Madrid (ref: Nanofrontmag) and CSIC (ref.: 201460E014), from CAPES Brazilian funding agency, and from the E.C. through a FP7-ICT project (Grant No. 318144). The authors thank Raquel Álvaro (from IMM-CSIC) for the planarization of the initial templates., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Adhesion enhancement of DLC hard coatings by HiPIMS metal ion etching pretreatment

  • Santiago, José Antonio
  • Fernández-Martínez, Iván
  • Wennberg, A.
  • Molina-Aldareguia, Jon
  • Castillo-Rodríguez, Miguel
  • Rojas, T. Cristina
  • Sánchez-López, J.C.
  • González Sagardoy, María Ujué
  • García-Martín, José Miguel
  • Li, H.
  • Bellido-González, Victor
  • Monclús, M.A.
  • González-Arrabal, Raquel
Poor adhesion is a recurrent problem for the wider use of diamond-like carbon (DLC) coatings in industrial applications. In this work, we investigate the effectiveness of high-power impulse magnetron sputtering (HiPIMS) metal ion etching to improve the adhesion of DLC coatings on high speed steel substrates. The influence of HiPIMS pretreatment parameters, the metal ion selection for the process and the addition of bonding layers on the adhesion properties were studied. Daimler-Benz and nanoscratch test methods were used to evaluate the adhesion. The elemental composition, morphology and microstructure of the samples were evaluated by EELS, SEM, AFM and HRTEM. In general, samples pretreated with HiPIMS metal ion etching withstand larger critical loads than those pretreated by conventional Ar+ glow discharge and bonding layers. The pretreatment is proven to be very effective at removing surface contaminants and providing a gradual interface. The selection of Cr over Ti contributes to a significant improvement on the adhesion due to the reduction of the oxygen level at the interface thus ensuring an optimal coating-substrate contact and a more compliant structure, which prevents the delamination failure., The research leading to these results has received funding from Madrid region under programme S2013/MIT-2775, DIMMAT project. Financial support from MINECO under projects (RADIAFUS IV ENE2015-70300-C3-3-R, MAT2014-59772-C2-1-P, MAT2015-69035-REDC FUNCOAT+), Leverhulme International Network Grant (CARBTRIB) and EUROfusion Consortium under project AWP15-ENR-01/CEA-02 are also acknowledged, as well as the service from the X-SEM Laboratory at IMN under project CSIC13-4E-1794 with support from EU (FEDER, FSE)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Contribución de congreso (ConferenceOutput)

Synergic antibacterial coatings combining Ti nanocolumns and Te nanorods

  • Medina Cruz, David
  • González Sagardoy, María Ujué
  • Tien-Street, William
  • Fernández Castro, Marcial
  • Fernández-Martínez, Iván
  • Webster, Thomas J.
  • García-Martín, José Miguel
Trabajo presentado en el 1st Spanish Conference on Biomedical Aplications of Nanomaterials, celebrado en Madrid, los días 7 y 8 de junio de 2018, The glancing angle deposition technique by magnetron sputtering is a scalable technique that allows the production of nanostructured coatings in large areas [1]. In recent works, we have shown that nanocolumnar coatings made of Ti were successfully prepared with this method [2] and how they exhibited selective behavior towards osteoblast and Staphylococcus aureus (S. a.) proliferation [3]: the biocompatibility towards human cells was preserved, whilst the adherence and proliferation of S. a. were dramatically reduced, not only with commercial strains but also with clinical ones coming from infected patients. In this new work, not only Gram-positive bacteria but also Gram-negative ones (E. Coli) have been used to test the response of different coatings fabricated in two set-ups, one of them being a semi-industrial equipment, in order to check the robustness of this approach. Moreover, Te nanorods were synthesized on top of the nanocolumns (see Fig.) using a hydrothermal and environmentally-friendly approach. It will be shown that the antibacterial behavior is enhanced when this synergic route combining Ti nanocolumns and Te nanorods is used, especially in the case of long nanocolumns. Furthermore, all the coatings remain biocompatible for human cells and allow for their proliferation., Funding from MINECO (MAT2014-59772-C2-1), Fundación Domingo Martínez, and Fulbright Commission is acknowledged., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Contribución de congreso (ConferenceOutput)

Nanostructured coatings made by oblique deposition with sputtering

  • González Sagardoy, María Ujué
  • Álvarez, Rafael
  • Palmero, Alberto
  • García-Martín, José Miguel
Trabajo presentado en el 7th Spanish Workshop in Nanolithography, celebrado en Madrid, del 23 al 25 de octubre de 2017, A low-cost approach to fabricate nanostructured coatings will be presented: oblique deposition with sputtering. This technique is energetically efficient and environmentally friendly, since it takes place at room tem perature in one single step and no chemicals are involved (thus without recycling problems). Any kind of flat substrate can be used, and with feasible modifications, it can be scaled up to large surfaces. The growth regimes [1-3] and the deposition rate [4] of the nanostructured coatings obtained using two different materials, gold and titanium, will be discussed. It will be shown that the formation of nanostructures is the outcome of self-shadowing effects when vapor species arrive at the film surface along a tilted direction (see Figure). In fact, we have developed a fundamental framework to explain the different morphologies obtained, the key factor being the thermalization degree of sputtered particles that accounts for the collisional processes in the vapor phase between the travelling atoms and the plasma species. In particular, at low pressures, tilted nanocolumns can be obtained when the angle of incidence surpasses a critical threshold. Moreover, if substrate rotation is used, the majority of nanostr uctures becomes axially symmetric. Several applications of such nanocolumnar coatings will be reviewed, especially focusing in two of them: black metals [5] and antibacterial coatings [6]., Support from the IDEA² Award (M+Vision Consortium) and funding from MINECO (MAT2014-59772-C2-1, MAT2015-69035-REDC) and Domingo Martinez Foundation are acknowledged. We also acknowledge the service from the X-SEM Laboratory at IMM, and funding from MINECO under project CSIC13-4E1794 with support from EU (FEDER, FSE)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Contribución de congreso (ConferenceOutput)

Black gold coatings fabricated by glancing angle deposition with sputtering

  • González Sagardoy, María Ujué
  • Álvarez, Rafael
  • Palmero, Alberto
  • García-Martín, José Miguel
Trabajo presentado en el 15th International Conference on Near-Field Optics, Nanophotonics and Related Techniques, NFO15, celebrado en Troyes (Francia), del 26 al 31 de agosto de 2018, Black metal coatings are metallic coatings that exhibit high absorption in a certain region of the electromagnetic spectra. They are of interest in a wide range of applications such as radiative heat exchangers, solar energy absorbers, photovoltaic cells electrodes, separators to avoid cross effects in optical devices, thermal light emitters, or biosensors electrodes, to name a few. In particular, gold is frequently used due to its high resistance to oxidation. In the last few years, we have fabricated metallic coatings with nanocolumnar morphology by means of glancing angle deposition with magnetron sputtering [1-4]. This technique allows for obtaining nanostructured coatings onto any kind of flat substrates and it can be scaled up to large areas. Depending on the deposition parameters (such as gas pressure, tilt angle, substrate rotation, etc.), the nanocolumnar structure can be controlled, giving rise to different properties. In this work, we report the fabrication of black gold coatings in the visible range with this fabrication technique [5]. We will present the optical properties of the nanostructured films, showing that high tilt angle is needed to achieve the black metal behaviour (see Figure 1) with reflectivity below 10% in the 400-700 nm range for Au films deposited on Si. We will analyse the morphological characteristics of the samples in order to understand the main features responsible for this black metal behaviour., The authors acknowledge MINECO (Projects MAT2014-59772-C2-1, MAT2015-69035-REDC and CSIC13-4E-1794) and EU (FEDER, FSE) for financial support., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Contribución de congreso (ConferenceOutput)

Magnetic Properties of Fe3O4 antidots arrays synthesized by atomic layer deposition and focused ion beam lithography

  • Vega, Fidel
  • Palma, Juan Luis
  • Pereira, A.
  • Álvaro Bruna, Raquel
  • García-Martín, José Miguel
  • Escrig, Juan
Trabajo presentado en el XVII Brazilian MRS Meeting, celebrado en Natal (Brasil), del 16 al 20 de septiembre de 2018, Magnetic films of magnetite (Fe3O4) with controlled defects, usually called antidots arrays, where synthesized by a new technique called AFIR (Artificial Force Induced Reaction), that considers the deposition of a thin film by atomic layer deposition, the generation of holes using focused ion beam milling in the case of squared and hexagonal lattices, and the subsequent thermal reduction process of antidots arrays. Magnetic characterizations were carried out by magneto optic Kerr effect, showing the enhancement of the coercivity for the antidots arrays. The presence of the ordered non-magnetic holes induces a demagnetization field distribution that change the magnetization switching mechanism, and thermal reduction from Fe2O3 to Fe3O4 produces vacancies (porosity) in the material. Magnetic behavior was studied by mean of micromagnetic simulations, in where was possible to simulate the vacancies in the continuous film and the controlled defects. This technique opens a new route of manufacture ordered antidots arrays of magnetic oxides with variable lattice parameters., The authors acknowledge financial support from Fondequip (refs. EQM120045 and EQM140092), from Fondecyt (ref. 1150952 and 11150671), from DICYT, from the Spanish MINECO (ref. MAT2014-59772-C2-1-P) and from the Basal Proyect (ref. FB0807)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Contribución de congreso (ConferenceOutput)

Structural and magnetic properties of L10 FePt/{MgO, W, or Pt }/L10 FePt trilayers

  • Kaidatzis, Andreas
  • Giannopoulos, Georgios
  • Psycharis, V.
  • García-Martín, José Miguel
  • Varvaro, G.
  • Testa, A. M.
  • Niarchos, Dimitrios
Trabajo presentado en el XXXII Panhellenic Conference on Solid State Physics and Materials Science, celebrado en Ioannina (Grecia), del 18 al 21 de septiembre de 2016, Nowadays there is an urgent need for enhancing data storage capacity of hard disk drives due to the rapid increase of digital data volume produced worldwide. New effective approaches are required to push the recording areal density beyond the limit of 1 Tbit/in2 of state-of-art hard disk drives. A promising alternative is 3D-magnetic recording, where stacking magnetic layers with different magnetic properties are used [1]. In this work we report on the morpho-structural and magnetic properties of FePt/interlayer (MgO, Pt or W) /FePt magnetron sputtered trilayers, as a base structure towards 3D magnetic recording systems. The stack is grown on an MgO (100) substrate and consists of two magnetically hard FePt layers with a thickness of 20 and 10 nm separated by an interlayer of variable thickness (5 up to 50 nm). Fig 1a summarizes the coercivity for all MgO, W or Pt interlayer samples; the layers seem to be coupled even at 20 nm of MgO or W interlayer thickness. However, at 5 nm interlayer thickness, hysteresis loops for W or MgO interlayers are those of a film stack of partially coupled ferromagnetic layers( Figure 1b), whereas a fully decoupled magnetic trilayer is obtained for a Pt interlayer, in agreement to previous reports [2] and also supported by magnetic force microscopy imaging. Finally, electron diffraction patterns and dark field images analysis indicate that most of FePt grains grow in the L10 phase with the (001) planes parallel to the substrate and the MgO interlayer grows oriented as the substrate., Funding from the E.C. is acknowledged (Grant No. 318144 and 280670) & MINECO (MAT2014-59772-C2-1-P), Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Citric juice-mediated synthesis of tellurium nanoparticles with antimicrobial and anticancer properties

  • Medina Cruz, David
  • Tien-Street, William
  • Zhang, Bohan
  • Huang, Xinjing
  • Vernet Crua, Ada
  • Nieto-Argüello, Alfonso
  • Cholula-Díaz, Jorge L.
  • Martínez Orellana, Lidia
  • Huttel, Yves
  • González Sagardoy, María Ujué
  • García-Martín, José Miguel
  • Webster, Thomas J.
Bacterial infections and cancer are two of the most significant concerns that the current healthcare system should tackle nowadays. Green nanotechnology is presented as a feasible solution that is able to produce materials with significant anticancer and antibacterial activity, while overcoming the main limitations of traditional synthesis. In the present work, orange, lemon and lime extracts were used as both reducing and capping agents for the green synthesis of tellurium nanoparticles (TeNPs) using a microwave-assisted reaction. TeNPs showed a uniform size distribution, and rod- and cubic-shapes, and were extensively characterized in terms of morphology, structure and composition using TEM, SEM, XPS, XRD, FTIR and EDX analysis. TeNPs showed an important antibacterial activity against both Gram-negative and -positive bacteria in a range concentrations from 5 to 50 μg mL−1 over a 24-hour time period. Besides, nanoparticles showed an anticancer effect towards human melanoma cells over 48 hours at concentrations up to 50 μg mL−1. Moreover, the Te nanostructures showed no significant cytotoxic effect towards human dermal fibroblast at concentrations up to 50 μg mL−1. Therefore, we present an environmentally-friendly and cost-effective synthesis of TeNPs using only fruit juices and showing enhanced and desirable biomedical properties towards both infectious diseases and cancer., This work was supported by the Chemical Engineering Department at Northeastern University. Funding from MINECO (MAT2014-59772-C2-1-P and MAT2014-59772-C2-2-P) and the European Union [grant number ERC-2013-SyG 610256 NANOCOSMOS] is acknowledged. We also acknowledge the service from the MiNa Laboratory at IMN funded by CM (S2013/ICE2822), MINECO (CSIC13-4E-1794) and the EU (FEDER, FSE)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Investigation of split CoFeB/Ta/CoFeB/MgO stacks for magnetic memories applications

  • Kaidatzis, Andreas
  • Gopman, Daniel B.
  • Bran, Cristina
  • García-Martín, José Miguel
  • Vázquez Villalabeitia, Manuel
  • Niarchos, Dimitrios
We report on the static and dynamic magnetic properties of W/CoFeB/Ta/CoFeB/MgO stacks, where the CoFeB layer is split in two by a 0.3 nm-thick Ta “dusting” layer. A total CoFeB thickness between 1.2 and 2.4 nm is studied. Perpendicular magnetic anisotropy is obtained for thickness below 1.8 nm even at the as-deposited stacks, and it is enhanced after annealing. Saturation magnetization is 1520 (1440) kA/m before (after) annealing, increased compared to non-split CoFeB layers. Ferromagnetic resonance measurements show that high magnetic anisotropy energy may be achieved (effective anisotropy field 0.571 ± 0.003 T), combined to a moderate Gilbert damping (0.030 ± 0.001). We argue that the above characteristics make the split-CoFeB system advantageous for spintronics applications., Funding from the EC (Grant No. 318144 and 686056), from the Spanish MINECO (ref. MAT2014-59772-C2-1-P) and from Comunidad de Madrid (Nanofrontmag, ref. P2013/MIT-2850), is acknowledged., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Antibacterial Nanostructured Ti Coatings by Magnetron Sputtering: From Laboratory Scales to Industrial Reactors

  • Álvarez, Rafael
  • Muñoz-Piña, Sandra
  • González Sagardoy, María Ujué
  • Izquierdo-Barba, Isabel
  • Fernández-Martínez, Iván
  • Rico, Víctor J.
  • Arcos, Daniel
  • García-Valenzuela, Aurelio
  • Palmero, Alberto
  • Vallet-Regí, María
  • González-Elipe, Agustín R.
  • García-Martín, José Miguel
Based on an already tested laboratory procedure, a new magnetron sputtering methodology to simultaneously coat two-sides of large area implants (up to ~15 cm2) with Ti nanocolumns in industrial reactors has been developed. By analyzing the required growth conditions in a laboratory setup, a new geometry and methodology have been proposed and tested in a semi-industrial scale reactor. A bone plate (DePuy Synthes) and a pseudo-rectangular bone plate extracted from a patient were coated following the new methodology, obtaining that their osteoblast proliferation efficiency and antibacterial functionality were equivalent to the coatings grown in the laboratory reactor on small areas. In particular, two kinds of experiments were performed: Analysis of bacterial adhesion and biofilm formation, and osteoblasts–bacteria competitive in vitro growth scenarios. In all these cases, the coatings show an opposite behavior toward osteoblast and bacterial proliferation, demonstrating that the proposed methodology represents a valid approach for industrial production and practical application of nanostructured titanium coatings., The authors acknowledge the financial support from the European Regional Development Funds program (EU-FEDER) and the MINECO-AEI (201560E055, MAT2014-59772-C2-1-P, MAT2016-75611-R, and MAT2016-79866-R and network MAT2015-69035-REDC). The authors also thank the University of Seville (V and VI PPIT-US) and Fundación Domingo Martínez for financial support. M.V.-R. also thanks the European Research Council (advanced grant VERDI; ERC-2015-AdG proposal 694160). The authors thank the MiNa Laboratory at IMN funded by CM (S2018/NMT-4291 TEC2SPACE), MINECO (CSIC13-4E-1794), and the EU (FEDER, FSE) for the support., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

On the large near-field enhancement on nanocolumnar gold substrates

  • Díaz-Núñez, Pablo
  • García-Martín, José Miguel
  • González Sagardoy, María Ujué
  • González-Arrabal, Raquel
  • Rivera, A.
  • Alonso-González, Pablo
  • Martín-Sánchez, Javier
  • Taboada-Gutiérrez, Javier
  • González-Rubio, Guillermo
  • Guerrero-Martínez, Andrés
  • Bañares, Luis
  • Peña Rodríguez, Ovidio
One of the most important and distinctive features of plasmonic nanostructures is their ability to confine large electromagnetic fields on nanometric volumes; i.e., the so-called hot spots. The generation, control and characterization of the hot spots are fundamental for several applications, like surface-enhanced spectroscopies. In this work, we characterize the near-field distribution and enhancement of nanostructured gold thin films fabricated by glancing angle deposition magnetron sputtering. These films are composed of columnar nanostructures with high roughness and high density of inter-columnar gaps, where the electromagnetic radiation can be confined, generating hot spots. As expected, the hot spots are localized in the gaps between adjacent nanocolumns and we use scattering-type scanning near-field optical microscopy to image their distribution over the surface of the samples. The experimental results are compared with finite-difference time-domain simulations, finding an excellent agreement between them. The spectral dependence of the field-enhancement is also studied with the simulations, together with surface-enhanced Raman spectroscopy at different excitation wavelengths in the visible-NIR range, proving a broad-band response of the substrates. These findings may result in interesting applications in the field of surface-enhanced optical spectroscopies or sensing., P.D.N. acknowledges DIMMAT project funded by Madrid region under programme S2013/MIT-2775, the technical assistance provided by Dr. Judith Langer and CIC biomaGUNE for an internship to perform the SERS measurements. Funding from Universidad Politécnica de Madrid (VJIDOCUPM18OYPR) and MINECO (MAT2014-59772-C2-1-P and ENE2015-70300-C3-3-R) is also acknowledged, as well as the computer resources and technical assistance provided by CESVIMA (Centro de Supercomputación y Visualización de Madrid, Universidad Politécnica de Madrid) and the service from the MiNa Laboratory at IMN funded by CM (S2013/ICE2822), MINECO (CSIC13-4E-1794), the EU (FEDER, FSE) and funding by EUROfusion Consortium through project AWP15-ENR-01/CEA-02., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Kinetic energy-induced growth regimes of nanocolumnar Ti thin films deposited by evaporation and magnetron sputtering

  • Álvarez, Rafael
  • García-Valenzuela, Aurelio
  • Rico, Víctor J.
  • García-Martín, José Miguel
  • Cotrino, José
  • González-Elipe, Agustín R.
  • Palmero, Alberto
We experimentally analyze different growth regimes of Ti thin films associated to the existence of kinetic energy-induced relaxation mechanisms in the material's network when operating at oblique geometries. For this purpose, we have deposited different films by evaporation and magnetron sputtering under similar geometrical arrangements and at low temperatures. With the help of a well-established growth model we have found three different growth regimes: (i) low energy deposition, exemplified by the evaporation technique, carried out by species with typical energies in the thermal range, where the morphology and density of the film can be explained by solely considering surface shadowing processes, (ii) magnetron sputtering under weak plasma conditions, where the film growth is mediated by surface shadowing mechanisms and kinetic-energy-induced relaxation processes, and (iii) magnetron sputtering under intense plasma conditions, where the film growth is highly influenced by the plasma, and whose morphology is defined by nanocolumns with similar tilt than evaporated films, but with much higher density. The existence of these three regimes explains the variety of morphologies of nanocolumnar Ti thin films grown at oblique angles under similar conditions in the literature., The authors thank the European Regional Development Funds program (EU-FEDER) and the MINECO-AEI (201560E055, MAT2014-59772-C2-1-P, and MAT2016-79866-R and network MAT2015-69035-REDC) for financial support. The authors also acknowledge the financial support of the University of Seville (V and VI PPIT-US). The National Center for Accelerators (Seville, Spain) is also acknowledged., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Contribución de congreso (ConferenceOutput)

Environmentally-friendly coatings with antibacterial properties

  • García-Martín, José Miguel
Trabajo presentado en el TERMIS EU Meeting 2019, celebrado en Rodas (Grecia), del 27 al 31 de mayo de 2019, Orthopedic metal implants improve the quality of life of millions of patients each year. The main problem they present is infection, which depending on the type of device and the patient's health affects 0.5-5% of cases. Our approach to this problem is to use nanostructured coatings to reduce the risk of infection. In short, by magnetron sputtering at oblique incidence [1] we fabricate a coating formed by titanium nanocolumns that develop as the result of atomic shadowing processes in the ballistic deposition regime, see Figure. It is an energy efficient method that can be scaled-up to industry, since it takes place at room temperature in one single step and no chemicals are involved (thus without recycling problems)., Financial support from MINECO (MAT2014-59772-C2-1), MECD (PRX16/00383), Fundación Domingo Martínez and Fulbright Commission are appreciated.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Silver nanopillar coatings grown by glancing angle magnetron sputtering for reducing multipactor effect in spacecrafts

  • Troncoso, G.
  • García-Martín, José Miguel
  • González Sagardoy, María Ujué
  • Morales, Carlos
  • Fernández Castro, Marcial
  • Soler-Morala, Jimena
  • Galán, Luis
  • Soriano, Leonardo
We have studied nanometric high aspect ratio Ag nanopillar coatings exhibiting reduced secondary electron emission for the mitigation of multipactor effect in radio-frequency space devices of high frequency and high power. The Ag nanopillars have been grown by glancing angle deposition with DC magnetron sputtering. Some samples have been covered by a gold capping layer to reduce oxidation and aging effects. The secondary emission yield of the surfaces of these samples has been measured and compared to those of flat Ag and Au reference samples. The results show that high aspect ratio surface roughness at the nanometer scale significantly reduce the secondary emission yield of the surface. This reduction is more important for low electron energies, which is the most influencing energy range of electrons for multipactor. The multipactor region for the nanopillar coating presenting the best secondary emission yield properties has been simulated, finding practical suppression of multipactor effect. The high-frequency surface resistance of these samples has also been estimated from published computations for similar surface roughness patterns. It was found that such nanopillar coatings are compatible with the best accomplishments of present space industry., This investigation has been funded by the MINECO of Spain through the AYA2012-39832-C02-02, FIS2015-67367-C2-1-P, MAT2015-69035-REDC and MAT2014-59772-C2-1-P projects and by the Comunidad de Madrid through the NANOMAGCOST-CM Ref: P2018/NMT4321 project. One of the authors (C.M.) thanks MECD for FPU14/02020 grant. The authors also want to thank SEGAINVEX and SIdI from UAM for technical support, and to acknowledge the service from the MiNa Laboratory at IMN funded by Comunidad de Madrid (S2018/NMT-4291 TEC2SPACE), MINECO (CSIC13-4E-1794) and the European Union (FEDER, FSE)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Photo-Induced Self-Cleaning and Wettability in TiO2 Nanocolumn Arrays Obtained by Glancing-Angle Deposition with Sputtering

  • Fresno, Fernando
  • González Sagardoy, María Ujué
  • Martínez Orellana, Lidia
  • Fernández Castro, Marcial
  • Barawi, Mariam
  • Villar-García, Ignacio J.
  • Soler-Morala, Jimena
  • Reñones, Patricia
  • Luna, Mónica
  • Huttel, Yves
  • Peña O'Shea, Víctor A. de la
  • García-Martín, José Miguel
In this work, the preparation of regular nanosized columnar structures of titanium dioxide by means of glancing angle deposition with magnetron sputtering (MS-GLAD) followed by thermal annealing is reported. MS-GLAD gives rise to metallic titanium columnar structures with regular width and length that after thermal treatment are fully oxidized to form TiO2 nanocolumns that maintain the morphological features of the original metallic ones. Further functionalization with gold by means of multiple ion cluster source results in well-dispersed Au nanoparticles across the nanocolumns’ surface with a narrow size distribution centered at ca. 8.5 nm. The obtained nanostructures show photocatalytic self-cleaning activity as shown by the elimination of an organic layer deposited on their surface and the detection of hydroxyl radicals. Photoelectrochemical measurements show a better charge separation at the Au/TiO2 interface. In addition, wettability studies show that the degree of hydrophobicity of the surface is increased by the presence of nanocolumns, both in the dark and under UV illumination. This behavior is not modified by the presence of Au nanoparticles on the surface. The obtained results open up interesting implications in the tunability of the properties of nanostructured thin films for this kind of photo-activated application., Financial support from the Spanish Ministry of Science, Innovation, and Universities (MICINN) through the projects SOLPAC (ENE2017-89170-R, MCIU/AEI/FEDER, EU), MAT2014-59772-C2-1-P, and MAT2014-59772-C2-2-P is gratefully acknowledged. The authors also acknowledge the service from the MiNa Laboratory at IMN funded by Comunidad de Madrid (S2018/NMT-4291 TEC2SPACE), MICINN (CSIC13-4E-1794), and the EU (FEDER, FSE). Also, this work has been funded by the regional government of Madrid and European Structural Funds through their financial support to FotoArt-CM program (S2018/NMT-4367), and from Fundación Ramon Areces though the ArtLeaf project. M.B. thanks MICINN for a Juan de la Cierva Incorporación (IJC2019-042430-I) grant., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Photoinduced Charge Transfer and Trapping on Single Gold Metal Nanoparticles on TiO2

  • Luna, Mónica
  • Barawi, Mariam
  • Gómez-Moñivas, Sacha
  • Colchero, Jaime
  • Rodríguez-Peña, Micaela
  • Yang, Shanshan
  • Zhao, Xiao
  • Lu, Yi-Hsien
  • Chintala, Ravi
  • Reñones, Patricia
  • Altoe, Virginia
  • Martínez Orellana, Lidia
  • Huttel, Yves
  • Kawasaki, Seiji
  • Weber-Bargioni, Alexander
  • Peña O'Shea, Víctor A. de la
  • Yang, Peidong
  • Ashby, Paul D.
  • Salmerón, Miquel
We present a study of the effect of gold nanoparticles (Au NPs) on TiO2 on charge generation and trapping during illumination with photons of energy larger than the substrate band gap. We used a novel characterization technique, photoassisted Kelvin probe force microscopy, to study the process at the single Au NP level. We found that the photoinduced electron transfer from TiO2 to the Au NP increases logarithmically with light intensity due to the combined contribution of electron-hole pair generation in the space charge region in the TiO2-air interface and in the metal-semiconductor junction. Our measurements on single particles provide direct evidence for electron trapping that hinders electron-hole recombination, a key factor in the enhancement of photo(electro)catalytic activity., This work was supported by the Office of Basic Energy Sciences (BES) of the U.S. Department of Energy (DOE) under contract DE-AC02-05CH11231 through the Structure and Dynamics of Materials Interfaces Program (FWP KC31SM) and the Molecular Foundry. M.L. acknowledges funds from Comunidad de Madrid (P2018/EMT-4308), a Fulbright grant PRX16/00564, and the MCIU-AEI-FEDERUE (RTI2018-096937-B-C22 and MAT2014-59772-C2-1-P). J.C. acknowledges financial support from Ministerio de Ciencia e Innovación (MICINN) and the European Union through the project PID2019-104272RB-C52. Also, Y.H. acknowledges financial support from MCIU through MAT2014-59772-C2-2- P and L.M. from EC through ERC-2013-SYG-610256. V.A.P.O. and M.B. acknowledge the financial support from EC through ERC CoG HyMAP 648319, MINECO PID2019- 106315RB-I00 and ENE2017-89170-R, ″Comunidad de Madrid″ and European Structural Funds (FotoArt-CM project S2018/NMT-4367) and Fundación Ramón Areces (Art-Leaf project). M.B. also thanks the Juan de la Cierva Incorporación contract (IJC2019042430-I). X.Z. was supported by the NSF-BSF 359 grant number 1906014. The authors thank Prof. Eran Edri, María Ujué González Sagardoy, and Judit Meseguer- Oliver for fruitful discussions and Asylum customer support for help with modifications of the AFM.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Large-Area Nanopillar Arrays by Glancing Angle Deposition with Tailored Magnetic Properties

  • Navarro, Elena
  • González Sagardoy, María Ujué
  • Béron, Fanny
  • Tejo, Felipe
  • Escrig, Juan
  • García-Martín, José Miguel
Ferromagnetic films down to thicknesses of tens of nanometers and composed by polycrystalline Fe and Fe2O3 nanopillars are grown in large areas by glancing angle deposition with magnetron sputtering (MS-GLAD). The morphological features of these films strongly depend on the growth conditions. Vertical or tilted nanopillars have been fabricated depending on whether the substrate is kept rotating azimuthally during deposition or not, respectively. The magnetic properties of these nanopillars films, such as hysteresis loops squareness, adjustable switching fields, magnetic anisotropy and coercivity, can be tuned with the specific morphology. In particular, the growth performed through a collimator mask mounted onto a not rotating azimuthally substrate produces almost isolated well-defined tilted nanopillars that exhibit a magnetic hardening. The first-order reversal curves diagrams and micromagnetic simulations revealed that a growth-induced uniaxial anisotropy, associated with an anisotropic surface morphology produced by the glancing angle deposition in the direction perpendicular to the atomic flux, plays an important role in the observed magnetic signatures. These results demonstrate the potential of the MS-GLAD method to fabricate nanostructured films in large area with tailored structural and magnetic properties for technological applications., This research was funded by MINECO (MAT2014-59772-C2-1-P and FIS2016-76058). We also thank the service from the MiNa Laboratory at IMN funded by Comunidad de Madrid (project S2018/NMT-4291TEC2SPACE), Comunidad de Madrid NANOMAGCOST S2018/NMT-4321, MINECO (CSIC13-4E-1794) and the EU (FEDER, FSE). In Chile we acknowledge the financial support from Redes (190158), Basal Project (AFB180001), Fondecyt 1200302, ANID-PFCHA/Postdoctorado Becas Chile 74200122 and Dicyt-Usach 041931EM_POSTDOC. The Brazilian funding arises from São Paulo Research Foundation: 2017/10581-1 and 2020/07397-7; National Council for S., Peer reviewed
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Tuning the size, composition and structure of Au and Co50Au50 Nanoparticles by High-Power Impulse Magnetron Sputtering in gas-phase Synthesis

  • Mayoral, A.
  • Martinez, L.
  • García-Martín, J. M.
  • Fernández-Martínez, I.
  • García-Hernández, M.
  • Galiana, B.
  • Ballesteros, C.
  • Huttel, Y.
Gas-phase synthesis of nanoparticles with different structural and chemical distribution is reported using a circular magnetron sputtering in an ion cluster source by applying high-power impulses. The influence of the pulse characteristics on the final deposit was evaluated on Au nanoparticles. The results have been compared with the more common direct current approach. In addition, it is shown for the first time that high-power impulses in magnetron based gas aggregation sources allows the growth of binary nanoparticles, CoAu in this case, with a variety of crystalline and chemical arrangements which are analyzed at the atomic level.