Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 22
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Tesis doctoral (DoctoralThesis)

Desarrollo y optimización de formulaciones de poliamida de origen renovable con comportamiento ignífugo

  • Marset Gimeno, David
[ES] El principal objetivo de la presente tesis doctoral se ha centrado en la obtención, desarrollo y optimización de formulaciones de poliamida de origen renovable con aditivos que mejoren las propiedades mecánicas, morfológicas, térmicas, termomecánicas y de comportamiento frente al fuego. En una primera fase se ha trabajado con mezclas de poliamida con un origen parcial biológico obtenido de la reacción del ácido dicarboxílico del aceite de ricino con la 1,6-hexametilendiamina (HMDA) derivada del petróleo mediante policondensación. De esta manera se obtiene una BioPA 610 con un contenido bio entre el 60-63% en peso. Esta PA610 se combinó con nanotubos de Halloysita (HNTs) en diferentes cargas para evaluar su efecto en la matriz y sus propiedades. Se obtuvo un gran aumento de rigidez con la incorporación de carga en la matriz polimérica además de un ligero aumento de la dureza. Las propiedades morfológicas muestran una buena dispersión de los nanotubos en el material. En cuanto a las propiedades térmicas los HTNs no suponen una gran variación de las características con respecto al polímero base. Los resultados termomecánicos muestran un gran aumento en el módulo de almacenamiento. Por otro lado, se estudiaron las propiedades de comportamiento frente al fuego de las mezclas de PA610 y HNTs mediante las técnicas del cono calorimétrico, índice límite de oxígeno (LOI), opacidad y toxicidad de los gases producidos, poder calorífico de combustión y ensayo UL-94. De los resultados obtenidos se aprecia una buena reducción del calor liberado con el aumento de carga de HNTs, una ligera disminución en el valor del LOI. En cuanto a la opacidad del humo desprendido, la presencia de HNTs no afecta demasiado en la liberación del humo, pero sí se obtiene una buena reducción del CO2 desprendido durante la combustión del material. El poder calorífico muestra una disminución de hasta 10 MJ/Kg con respecto a la PA610 sin aditivo. Por último, el ensayo de UL-94 no supone variación de resultados en las diferentes muestras analizadas. En una última fase se trabajó con grafito expandido (EGr) combinado dentro de la matriz polimérica de poliamida 1010 de origen biológico obtenida 100% de fuentes renovables. En esta fase se incorporaron cargas de EGr entre 2,5% y 10% en peso. Se estudiaron propiedades mecánicas, térmicas y termomecánicas, así como el análisis del color, morfología, hidrofobia, captación de agua y su comportamiento frente al fuego. Mecánicamente se apreció una gran mejora en la rigidez del material. En las propiedades térmicas se mejoró el grado de cristalinidad del material. El análisis termomecánico mostró un aumento en el módulo (E) y en el módulo de almacenamiento (E'). El estudio de la hidrofobia y la captación de agua dio como resultado una reducción en la absorción de agua y un aumento de la hidrofobicidad del material. Por último, en cuanto a las propiedades del material frente al fuego, se consiguió reducir en gran medida la liberación de calor emitido. El valor del índice límite de oxígeno se reduce ligeramente y el ensayo de la UL-94 muestra una mejora de V-2 a V-1 en la clasificación del compuesto con la incorporación de EGr frente al polímero sin aditivar., [CA] El principal objectiu de la present tesi doctoral s'ha centrat en l'obtenció, el desenvolupament i l'optimització de formulacions de poliamida d'origen renovable amb additius que millorin les propietats mecàniques, morfològiques, tèrmiques, termomecàniques i de comportament davant del foc. En una primera fase s'ha treballat amb barreges de poliamida amb un origen parcial biològic obtingut de la reacció de l'àcid dicarboxílic de l'oli de ricí amb la 1,6-hexametilendiamina (HMDA) derivada del petroli mitjançant policondensació. D¿aquesta manera s'obté una BioPA 610 amb un contingut bio entre el 60-63% en pes. Aquesta PA610 es va combinar amb nanotubs de Halloysita (HNTs) en diferents càrregues per avaluar el seu efecte a la matriu i les seues propietats. Es va obtenir un gran augment de rigidesa amb la incorporació de càrrega a la matriu polimèrica a més d'un lleuger augment de la duresa. Les propietats morfològiques mostren una bona dispersió dels nanotubs al material. Quant a les propietats tèrmiques, els HTNs no suposen una gran variació de les característiques respecte al polímer base. Els resultats termomecànics mostren un gran augment en el mòdul d'emmagatzematge. D'altra banda, es van estudiar les propietats de comportament davant del foc de les barreges de PA610 i HNTs mitjançant les tècniques del con calorimètric, índex límit d'oxigen (LOI), opacitat i toxicitat dels gasos produïts, poder calorífic de combustió i assaig UL-94. Dels resultats obtinguts s'aprecia una bona reducció de la calor alliberada amb l'augment de càrrega de HNTs, una lleugera disminució al valor del LOI. Quant a l'opacitat del fum desprès, la presència de HNTs no afecta gaire en l'alliberament del fum, però sí que s'obté una bona reducció del CO2 desprès durant la combustió del material. El poder calorífic mostra una disminució de fins a 10 MJ/Kg respecte de la PA610 sense additiu. Finalment, l'assaig d'UL-94 no suposa variació de resultats a les diferents mostres analitzades. En una darrera fase es va treballar amb grafit expandit (EGr) combinat dins de la matriu polimèrica de poliamida 1010 d'origen biològic obtinguda 100% de fonts renovables. En aquesta fase es van incorporar càrregues d'EGr entre el 2,5% i el 10% en pes. Es van estudiar propietats mecàniques, tèrmiques i termomecàniques, així com l'anàlisi del color, la morfologia, la hidrofòbia, la captació d'aigua i el seu comportament davant del foc. Mecànicament es va apreciar una gran millora en la rigidesa del material. A les propietats tèrmiques es va millorar el grau de cristal·linitat del material. L'anàlisi termomecànica va mostrar un augment al mòdul (E) i al mòdul d'emmagatzematge (E'). L'estudi de la hidrofòbia i la captació d'aigua va donar com a resultat una reducció de l'absorció d'aigua i un augment de la hidrofobicitat del material. Finalment, quant a les propietats del material davant del foc, es va aconseguir reduir en gran mesura l'alliberament de calor emesa. El valor de l'índex límit d'oxigen es redueix lleugerament i l'assaig de la UL-94 mostra una millora de V-2 a V-1 a la classificació del compost amb la incorporació d'EGr davant del polímer sense additivar., [EN] The main objective of this doctoral thesis has focused on obtaining, developing and optimizing polyamide formulations of renewable origin with additives that improve the mechanical, morphological, thermal, thermomechanical and fire behavior properties. In a first phase, has been carried out an experimental with polyamide mixtures with a partial biological origin obtained from the reaction of the dicarboxylic acid of castor oil with 1,6-hexamethylenediamine (HMDA) derived from petroleum by means of polycondensation. In this way, a BioPA 610 with a bio content between 60-63% by weight is obtained. This PA610 was combined with Halloysite nanotubes (HNTs) at different loadings to evaluate its effect on the matrix and its properties. A large increase in stiffness was obtained with the incorporation of filler in the polymeric matrix in addition to a slight increase in hardness. The morphological properties show a good dispersion of the nanotubes in the material. Regarding the thermal properties, the HTNs do not imply a great variation of the characteristics with respect to the base polymer. The thermomechanical results show a large increase in the storage modulus. On the other hand, the fire behavior properties of the mixtures of PA610 and HNTs were studied using the calorimetric cone techniques, limit oxygen index (LOI), opacity and toxicity of the gases produced, calorific value of combustion and UL-94 test. From the results obtained, a good reduction of the heat released with the increase in the load of HNTs, a slight decrease in the value of the LOI, can be seen. Regarding the opacity of the smoke released, the presence of HNTs does not affect the release of smoke too much, but a good reduction of the CO2 released during the combustion of the material is obtained. The calorific power shows a decrease of up to 10 MJ/Kg with respect to PA610 without additive. Lastly, the UL-94 test does not assume any variation in results in the different samples analysed. In a final phase, expanded graphite (EGr) combined within the polyamide 1010 polymeric matrix of biological origin obtained 100% from renewable sources was worked on. In this phase, EGr loads between 2.5% and 10% by weight were incorporated. Mechanical, thermal and thermomechanical properties were studied, as well as the analysis of color, morphology, hydrophobicity, water uptake and its behavior against fire. Mechanically, a great improvement in the rigidity of the material was appreciated. In the thermal properties, the degree of crystallinity of the material was improved. The thermomechanical analysis showed an increase in the modulus (E) and in the storage modulus (E'). The study of hydrophobicity and water uptake resulted in a reduction in water absorption and an increase in the hydrophobicity of the material. Finally, regarding the properties of the material against fire, it was possible to greatly reduce the release of emitted heat. The value of the oxygen limit index is slightly reduced and the UL-94 test shows an improvement from V-2 to V-1 in the classification of the compound with the incorporation of EGr compared to the polymer without additives., This research was funded by the Ministry of Science, Innovation, and Universities (MICIU) project numbers MAT2017-84909-C2-2-R and AGL2015- 63855-C2-1-R. Project funded with grant number PID2020-116496RB-C22 funded by the Ministry of Science and Innovation MCIN/AEI/10.13039/501100011033 and grant number AICO/2021/025 funded by Generalitat Valenciana. AITEX wants to thank CDTI (Centro para el Desarrollo Tecnológico Industrial) within the framework of grants for Technological Centres of Excellence “Cervera” (CER- 20211013). The author would like to thank the INTERREG SUDOE NABITEX project (SOE2/P1/P0524) for allowing him to participate in it as part of his training.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Upgrading Recycled Polypropylene from Textile Wastes in Wood Plastic Composites with Short Hemp Fiber

  • Burgada, Francisco
  • Fages, Eduardo
  • Arrieta, Marina P.
  • Quiles-Carrillo, Luis|||0000-0001-8037-2215
  • Lascano-Aimacaña, Diego Sebastián|||0000-0002-0996-1946
  • Ivorra-Martinez, Juan|||0000-0001-8968-4899
  • Fenollar, Octavio|||0000-0003-4323-7414
[EN] This research reports the manufacturing and characterization of green composites made from recycled polypropylene obtained from the remnants of polypropylene non-woven fabrics used in the textile industry and further reinforced with short hemp fibers (SHFs). To improve the interaction of the reinforcing fibers with the recycled polymeric matrix, two types of compatibilizing agents (maleic anhydride grafted, PP-g-MA, and maleinized linseed oil, MLO) were added during melt-processing, the percentage of which had to remain constant concerning the amount of fiber loading to ensure complete reactivity. Standardized test specimens were obtained by injection molding. The composites were characterized by mechanical (tensile, impact, and hardness), thermal (DSC, TGA), thermomechanical, FTIR, and FESEM microscopy tests. In addition, color and water uptake properties were also analyzed. The results show that the addition of PP-g-MA to rPP was satisfactory, thus improving the fiber-matrix interaction, resulting in a marked reinforcing effect of the hemp fibers in the recycled PP matrix, which can be reflected in the increased stiffness of the samples. In parallel to the compatibilizing effect, a plasticizing effect was obtained by incorporating MLO, causing a decrease in the glass transition temperature of the composites by approximately 6 °C and an increase in ductility compared to the unfilled recycled polypropylene samples., AITEX wants to thank the European Regional Development Fund (ERDF) from the European Union for co-funding the project "NABITEX-Innovative technical textiles based on SUDOE natural fibers to be applied in Habitat Sector" through the Interreg SUDOE Program (SOE2/P1/P0524). AITEX wants to acknowledge that the MELTEX project (CIRCULAR ECONOMY APPLIED TO TEXTILEWASTE OF THERMOPLASTIC ORIGIN) was funded by the Conselleria d'Economia Sostenible, Sectors Productius, Comerc i Treball de la Generalitat Valenciana, through IVACE and was co-funded by ERDF from the European Commission within the framework of the Operational Programme FEDER for the Comunitat Valenciana 2014-2020 (IMAMCI/2020/1).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Clasificación de objetos usando percepción bimodal de palpación única en acciones de agarre robótico, Object classification using bimodal perception data extracted from single-touch robotic grasps

  • Velasco, E.
  • Zapata-Impata, B.S.
  • Gil, P.
  • Torres, F.
[ES] Este trabajo presenta un método para clasificar objetos agarrados con una mano robótica multidedo combinando en un descriptor híbrido datos propioceptivos y táctiles. Los datos propioceptivos se obtienen a partir de las posiciones articulares de la mano y los táctiles se extraen del contacto registrado por células de presión instaladas en las falanges. La aproximación propuesta permite identificar el objeto aprendiendo de forma implícita su geometría y rigidez usando los datos que facilitan los sensores. En este trabajo demostramos que el uso de datos bimodales con técnicas de aprendizaje supervisado mejora la tasa de reconocimiento. En la experimentación, se han llevado a cabo más de 3000 agarres de hasta 7 objetos domésticos distintos, obteniendo clasificaciones correctas del 95%con métrica F1, realizando una única palpación del objeto. Además, la generalización del método se ha verificado entrenando nuestro sistema con unos objetos y posteriormente, clasificando otros nuevos similar, [EN] This work presents a method to classify grasped objects with a multi-fingered robotic hand combining proprioceptive and tactile data in a hybrid descriptor. The proprioceptive data are obtained from the joint positions of the hand and the tactile data are obtained from the contact registered by pressure cells installed on the phalanges. The proposed approach allows us to identify the grasped object by learning the contact geometry and stiness from the readings by sensors. In this work, we show that using bimodal data of different nature along with supervised learning techniques improves the recognition rate. In experimentation, more than 3000 grasps of up to 7 dierent domestic objects have been carried out, obtaining an average F1 score around 95 %, performing just a single grasp. In addition, the generalization of the method has been verified by training our system with certain objects and classifying new, similar ones without any prior knowledge., Este trabajo ha sido financiado con Fondos Europeos de Desarrollo Regional (FEDER), Ministerio de Economía, Industria y Competitividad a través del proyecto DPI2015-68087-R y la ayuda pre-doctoral BES-2016-078290, y también gracias al apoyo de la Comisión Europea y del programa Interreg V. Sudoe a través del proyecto SOE2/P1/F0638.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Development and Characterization of Environmentally Friendly Wood Plastic Composites from Biobased Polyethylene and Short Natural Fibers Processed by Injection Moulding

  • Dolza, Celia
  • Fages, Eduardo
  • Gonga, Eloi
  • Gómez-Caturla, Jaume|||0000-0001-8680-4509
  • Balart, Rafael|||0000-0001-5670-7126
  • Quiles-Carrillo, Luis|||0000-0001-8037-2215
[EN] Environmentally friendly wood plastic composites (WPC) with biobased high density polyethylene (BioHDPE) as the polymer matrix and hemp, flax and jute short fibers as natural reinforcements, were melt-compounded using twin-screw extrusion and shaped into pieces by injection molding. Polyethylene-graft-maleic anhydride (PE-g-MA) was added at two parts per hundred resin to the WPC during the extrusion process in order to reduce the lack in compatibility between the lignocellulosic fibers and the non-polar polymer matrix. The results revealed a remarkable improvement of the mechanical properties with the combination of natural fibers, along with PE-g-MA, highly improved stiffness and mechanical properties of neat BioHDPE. Particularly, hemp fiber drastically increased the Young¿s modulus and impact strength of BioHDPE. Thermal analysis revealed a slight improvement in thermal stability with the addition of the three lignocellulosic fibers, increasing both melting and degradation temperatures. The incorporation of the fibers also increased water absorption due to their lignocellulosic nature, which drastically improved the polarity of the composite. Finally, fire behavior properties were also improved in terms of flame duration, thanks to the ability of the fibers to form char protective barriers that isolate the material from oxygen and volatiles., : This research was funded by the Ministry of Science, Innovation, and Universities (MICIU) project number MAT2017-84909-C2-2-R. AITEX wants to thank the European Regional Development Fund (ERDF) from the European Union for co-funding the project NABITEX Innovative technical textiles based on SUDOE natural fibers to be applied in Habitat Sector through the Interreg SUDOE Program (SOE2/P1/P0524). L.Q.-C. wants to thank Universitat Politècnica de València for his post-doctoral PAID-10-20 grant from (SP20200073). J.G.-C. wants to thank Universitat Politècnica de València for his FPI grant from (SP20200080).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Photocatalytic water gas shift using visible or simulated solar light for the efficient, room-temperature hydrogen generation

  • Sastre Calabuig, Francesc
  • Oteri, Marica
  • Corma Canós, Avelino|||0000-0002-2232-3527
  • García Gómez, Hermenegildo|||0000-0002-9664-493X
Gold nanoparticles supported on P25 TiO2 act as highly efficient photocatalysts for promoting the simultaneous H2O reduction to H-2 and CO oxidation to CO2. This photocatalytic process can be performed using simulated solar light as well as light from a LED quasi monochromatic centred at 450 nm, indicating that not only UV but also visible light promotes the reaction. This novel photocatalytic reaction corresponds to the water gas shift which is an endothermic process that is currently carried out on a large industrial scale at temperatures about 350 degrees C. In contrast, the photocatalytic process is performed at ambient temperature with no other energy requirement than sunlight. Other related TiO2 and CeO2 photocatalysts containing noble metals (Pt or Pd) behave similarly, but with lower efficiency both in the UV and in the visible region than Au/TiO2., Financial support from the Spanish Ministry of Economy and Competitiveness through the Severo Ochoa program as well as operating grants (Consolider Ingenio Multicat and CTQ-2012-363531) is gratefully acknowledged. Thanks are due to the EU for partial funding of the networking through the TRAIN2 SUDDOE project. M.O. thanks the region of Calabria for financial support during her stay at Valencia.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

The Effect of Varying the Amount of Short Hemp Fibers on Mechanical and Thermal Properties of Wood Plastic Composites from Biobased Polyethylene Processed by Injection Molding

  • Dolçà, Celia
  • Fages, Eduardo
  • Gonga, Eloi
  • Garcia-Sanoguera, David|||0000-0002-1923-9519
  • Balart, Rafael|||0000-0001-5670-7126
  • Quiles-Carrillo, Luis|||0000-0001-8037-2215
[EN] Biobased HDPE (bioHDPE) was melt-compounded with different percentages (2.5 to 40.0 wt.%) of short hemp fibers (HF) as a natural reinforcement to obtain environmentally friendly wood plastic composites (WPC). These WPC were melt-compounded using a twin-screw extrusion and shaped into standard samples by injection molding. To improve the poor compatibility between the high non-polar BioHDPE matrix and the highly hydrophilic lignocellulosic fibers, a malleated copolymer, namely, polyethylene-graft-maleic anhydride (PE-g-MA), was used. The addition of short hemp fibers provided a remarkable increase in the stiffness that, in combination with PE-g-MA, led to good mechanical performance. In particular, 40 wt.% HF drastically increased the Young¿s modulus and impact strength of BioHDPE, reaching values of 5275 MPa and 3.6 kJ/m2, respectively, which are very interesting values compared to neat bioHDPE of 826 MPa and 2.0 kJ/m2. These results were corroborated by dynamic mechanical thermal analysis (DMTA) results, which revealed a clear increasing tendency on stiffness with increasing the fiber loading over the whole temperature range. The crystal structure was not altered by the introduction of the natural fibers as could be seen in the XRD patterns in which mainly the heights of the main peaks changed, and only small peaks associated with the presence of the fiber appeared. Analysis of the thermal properties of the composites showed that no differences in melting temperature occurred and the non-isothermal crystallization process was satisfactorily described from the combined Avrami and Ozawa model. As for the thermal degradation, the introduction of HF resulted in the polymer degradation taking place at a higher temperature. As for the change in color of the injected samples, it was observed that the increase in fiber generated a clear modification in the final shades of the pieces, reaching colors very similar to dark woods for percentages higher than 20% HF. Finally, the incorporation of an increasing percentage of fibers also increased water absorption due to its lignocellulosic nature in a linear way, which drastically improved the polarity of the composite., Project with grant number PID2020-116496RB-C22 funded by the Ministry of Science and Innovation MCIN/AEI/10.13039/501100011033 and grant number AICO/2021/025 funded by Generalitat Valenciana. European Regional Development Fund (ERDF) from the European Union for co-funding the project NABITEX Innovative technical textiles based on SUDOE natural fibers to be applied in Habitat Sector through the Interreg SUDOE Program (SOE2/P1/P0524) and CDTI (Centro para el Desarrollo Tecnológico Industrial) within the framework of grants for Technological Centres of Excellence Cervera (CER-20211013).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Tesis doctoral (DoctoralThesis)

Desarrollo y optimización de wood plastic composites con matriz biopolimérica y fibras naturales

  • Dolçà Camáñez, Celia
[ES] Debido a la preocupación por la contaminación derivada del uso de los plásticos y la gran cantidad de residuos generados a nivel mundial, se desarrollaron diferentes compuestos plásticos reforzados con fibras naturales respetuosos con el medio ambiente (WPC) para su caracterización y optimización. En primer lugar, se utilizó polietileno de alta densidad de base biológica (BioHDPE) como matriz polimérica y diferentes fibras cortas naturales como el cáñamo, el lino y el yute. Se mezclaron mediante extrusión de doble husillo y se moldearon en piezas mediante moldeo por inyección, se añadió un copolímero de injerto de etileno con anhídrido maleico (PE-g-MA) a dos partes por cien de resina al WPC durante el proceso de extrusión para reducir la falta de compatibilidad entre las fibras lignocelulósicas y la matriz polimérica. Como resultado, se observó en el análisis térmico, una ligera mejora de la estabilidad térmica de los compuestos reforzados con las tres fibras, aumentado la temperatura de fusión y de degradación del compuesto. Además, también aumentó la absorción de agua de los compuestos. Se obtuvo, especialmente, un aumento drástico del módulo de Young y de la resistencia al impacto de los compuestos con refuerzo de fibra de cáñamo. Debido a estos resultados, a continuación, se realizó un estudio con la misma matriz polimérica (BioHDPE) y diferentes porcentajes (2,5 a 40,0% en peso) de fibras cortas de cáñamo (HF) como refuerzo natural, utilizando la misma técnica por fusión y extrusión de doble husillo del compuesto que se moldeo por inyección. También se utilizó como agente compatibilizante, el copolímero maleinizado, de injerto de etileno con anhídrido maleico (PE-g-MA) para mejorar la escasa compatibilidad entre la matriz de BioHDPE altamente no polar y las fibras lignocelulósicas altamente hidrofílicas. El 40% en peso de fibra dio como resultado un aumento importante del módulo de Young y la resistencia al impacto del BioHDPE, obteniendo valores de 5275 MPa y 3,6 kJ/m2, respectivamente, en comparación con el bioHDPE puro de 826 MPa y 2,0 kJ/m2. En cuanto al cambio de color de las muestras inyectadas, se observó que el aumento de fibra generó una clara modificación en las tonalidades finales de las piezas, alcanzando colores muy similares a las maderas oscuras para porcentajes superiores al 20%.Finalmente, se desarrollaron nuevos composites de alto rendimiento mediomabiental utilizando un 30% de fibra corta de cáñamo y como matriz polimérica copolímero de polibutilén succinato-co-adipato paracialmente de origen renovable (BioPBSA). En este caso, para mejorar la interacción entre la fibra y la matriz no solo se empleó el injerto copolímero de PBSA injertado con anhídrido maleico (PBSA-g-MA), sino que se utilizaron diferentes aditivos por extrusión reactiva al composite como aditivos derivados del ácido itacónico de base biológica, como el dibutil itaconato (DBI) y un copolímero de PBSA injertado con ácido itacónico (PBSA-g-IA). La introducción de fibras de cáñamo, dieron como resultado una mejora en la rigidez del polímero base, el módulo de tracción del BioPBSA puro 281 MPa aumentó considerablemente alcanzando valores de 3482 MPa. Los compuestos con DBI obtuvieron una mejora en la ductilidad y una disminución en las propiedades de tracción, en contraste con las muestras compatibles con copolímeros que mejoraron la resistencia a la tracción., [CA] Degut a la preocupació per la contaminació derivada de l'us dels plàstics i la gran quantitat de residus generats a nivell mundial, es desenvoluparen diferents compostos reforçats amb fibres naturals respectuoses amb el medi ambient (WPC) per a la seva caracterització i optimització. En primer lloc, es va utilitzar polietilè d'alta densitat de base biològica (BioHDPE) com a matriu polimèrica i diferents fibres curtes naturals com el cànem, el lli i jute. Es van fondre mitjançant extrusió de doble tornavís i es moldejaren en peces mitjançant moldejat per injecció, es va afegir un copolímer d'empelt d'etlé i anhídrid maleic (PE-g-MA) a dues parts per cent de resina al WPC durant el procés d'extrusió per a reduir la falta de compatibilitat entre les fibres lignocel·lulòsiques i la matriu polimèrica. Com a resultat, es va observar en l'anàlisis tèrmica, una lleugera millora de l'estabilitat tèrmica dels compostos reforçats amb les tres fibres , augmentant la temperatura de fusió i de degradació dels compostos. Es va obtenir, especialment, un augment dràstic del mòdul de Young i de la resistència a l'impacte dels compostos amb reforç de fibra de cànem. Degut a aquestos resultats, a continuació es va realitzar un estudi amb la mateixa matriu polimèrica (BioHDPE) i diferents percentatges (2,5 a 40,0% en pes) de fibra curta de cànem (HF) com a reforç natural, utilitzant la mateixa tècnica per fusió i extrusió de doble tornavís del compost que es va moldejar per injecció. També es va utilitzar com agent compatibilitzant, el copolímer meleinitzat, anhídrid maleic d'empelt de polietilè (PE-g-MA) per millorar l'escassa compatibilitat entre la matriu de BioHDPE altament no polar i les fibres lignocel·lulòsiques altament hidrofíliques. El 40% en pes de fibra va donar com a resultat un augment important del mòdul de Young i la resistència a l'impacte del BioHDPE, obtenint valors de 5275 MPa i 3,6 kJ/m2, respectivament, en comparació amb el bioHDPE pur de 826 MPa i 2,0 kJ/m2. En quant al canvi de color de les mostres injectades, es va observar que l'augment de fibra va generar una clara modificació en les tonalitats finals de les peces, aconseguint colors molt similars a les fustes fosques per a percentatges superiors al 20%.Finalment, es van desenvolupar nous composites d'alt rendiment medioambiental utilitzant un 30% de fibra curta de cànem i com a matriu polimèrica copolímer de polibutilèn succinat-co-adipat paracialment d'origen renovable (BioPBSA). En aquest cas, per millorar la interacció entre la fibra i la matriu no només es va emprar l'empelt copolímer de PBSA empeltat amb anhídrid maleic (PBSA-g-MA), sinó que es van utilitzar diferents additius per extrusió reactiva al composite com a additius derivats de l'àcid itacònic de base biològica, com el dibutil itaconat (DBI) i un copolímer de PBSA empeltat amb àcid itacònic (PBSA-g-IA). La introducció de fibres de cànem, van donar com a resultat una millora en la rigidesa del polímer base, el mòdul de tracció del BioPBSA pur 281 MPa va augmentar considerablement aconseguint valors de 3482 MPa. Els compostos amb DBI van obtenir una millora en la ductilitat i una disminució en les propietats de tracció, en contrast amb les mostres compatibles amb copolímers que van millorar la resistència a la tracció., [EN] Due to the concern about the pollution derived from the use of plastics and the large amount of waste generated worldwide, different environmentally friendly natural fiber reinforced plastic compounds (WPC) were developed for their characterization and optimization. First, bio-based high-density polyethylene (BioHDPE) was used as the polymer matrix and different natural short fibers such as hemp, flax and jute. They were fused by twin screw extrusion and molded into pieces by injection molding. Polyethylene graft maleic anhydride (PE-g-MA) was added at two parts per hundred resin to the WPC during the extrusion process to reduce the lack of compatibility between the lignocellulosic fibers and the polymeric matrix. As a result, a slight improvement in the thermal stability of the composites reinforced with the three fibers was observed in the thermal analysis, increasing the melting temperature and degradation of the composite. In addition, it also increased the water absorption of the compounds. In particular, a drastic increase in the Young's modulus and the impact resistance of the hemp fiber reinforced composites was obtained. Due to these results, a study was then carried out with the same polymeric matrix (bioHDPE) and different percentages (2,5 to 40,0% by weight) of short hemp fibers (HF) as natural reinforcement, using the same technique by melt compunding and extrusion with a twin screw extruder, followed by injection moulding. The maleinized copolymer, polyethylene graft maleic anhydride (PE-g-MA) was also used as a compatibilizing agent to improve the poor compatibility between the highly non-polar BioHDPE matrix and the highly hydrophilic lignocellulosic fibers. The 40 wt% fiber resulted in a significant increase in Young's modulus and impact strength of BioHDPE, obtaining values of 5275 MPa and 3.6 kJ/m2, respectively, compared to pure bioHDPE of 826 MPa and 826 MPa. 2.0kJ/m2. Regarding the color change of the injected samples, it was observed that the increase in fiber generated a clear change in the final shades of the pieces, reaching colors very similar to dark wood for percentages greater than 20%.Finally, new green composites were developed using 30% short hemp fiber and a partically biobased polybutylene succinate-co-adipate copolymer (BioPBSA) as polymeric matrix. In this case, to improve the interaction between the fiber and the matrix, not only was the PBSA graft copolymer grafted with maleic anhydride (PBSA-g-MA) used, but different additives were used by reactive extrusion to the composite as additives derived from the Bio-based itaconic acid, such as dibutyl itaconate (DBI) and a copolymer of PBSA grafted with itaconic acid (PBSA-g-IA). The introduction of hemp fibers resulted in an improvement in the stiffness of the base polymer, the tensile modulus of pure BioPBSA 281 MPa increased considerably, reaching values of 3482 MPa. Composites with DBI obtained an improvement in ductility and a decrease in tensile properties, in contrast to samples compatible with copolymers that improved tensile strength., Agradecer al Fondo Europeo de Desarrollo Regional (FEDER) de la Unión Europea por cofinanciar el proyecto “NABITEX—Textiles técnicos innovadores basados en fibras naturales SUDOE para ser aplicados en el Sector del Hábitat” a través del Programa SUDOE de Interreg (SOE2/P1/ P0524).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Influence of pretreatments on commercial diamond nanoparticles on the photocatalytic activity of supported gold nanoparticles under natural Sunlight irradiation

  • Sempere Aracil, David
  • Dancikova, Mariana
  • Navalón Oltra, Sergio|||0000-0001-8423-0759
  • Alvaro Rodríguez, Maria Mercedes|||0000-0001-5070-4207
  • García Gómez, Hermenegildo|||0000-0002-9664-493X
Fenton-treated diamond (D) nanoparticles (NPs) are suitable support of gold to promote the wet peroxidation of phenol by H2O2. One of the drawbacks of this catalyst is the need of the pretreated commercial D NPs with a large excess of H2O2 and Fe(II) salts to remove the accompanying soot matter and introduce surface single bondOH groups on D. This process generates a large amount of waste waters and consumes large quantities of reagents, being desirable to develop alternative pretreatments for commercial D NPs. In the present manuscript we describe that a light combustion of the soot matter in a furnace under controlled temperature and time leads to a D support that after annealing at 500 ̊C under hydrogen affords a modified D material that is suitable as support of gold. We have found that annealing with hydrogen produces more efficient D samples than those without annealing or submitted to annealing under nitrogen. Characterization of the samples has shown that hydrogen annealing reduces surface Cdouble bond; length as m-dashO bonds to alcohols that are beneficial for anchoring gold nanoparticles. In this way, the resulting gold catalyst can set off the disappearance of phenol in water at pH 4 with only 2.6 equiv. of H2O2 assisted by Sunlight., Financial support by the Spanish Ministry of Economy and Competitiveness (MINECO, Severo Ochoa program and CTQ 2012-32316) and Universidad Politecnica de Valencia (PAID-06-11, no 2095) is gratefully acknowledged. We thank also to the EU funded TRAIN2 project for the partial funding of networking. SN thanks to the UPV for a lecturer contract.
DAU Arxiu Digital de la Universitat Ramon Llull
Publicación Artículo científico (JournalArticle)

Life Cycle Assessment of the Separation and Recycling of Fluorinated Gases Using Ionic Liquids in a Circular Economy FrameworkClick to copy article link

  • Jovell, Daniel
  • Pou, Josep Oriol
  • Llovell Ferret, Félix Lluís
  • González Olmos, Rafael
The stricter regulation regarding the use of fluorinated gases (F-gases), as a consequence of their high Global Warming Potential (GWP), represents a challenge for the refrigeration industry. The design of alternatives requires the recycling of the low to moderate GWP compounds from current refrigerant blends. However, there is not a developed and standardized technology available to recover them, and once the life cycle of the refrigeration equipment has ended, most gases are incinerated. Fluorinated ionic liquids (FILs) can effectively perform as absorbents to the complex separation of F-gas mixtures. In this work, a methodology based on the COSMO-RS thermodynamic package integrated into an Aspen Plus process simulator was used to evaluate the performance of an FIL to recover difluoromethane (R-32) from the commercial blend R-407F. The environmental sustainability of the recovery process (circular economy scenario) was analyzed with a life cycle assessment (LCA) approach, comparing the obtained results with the conventional R-32 production (benchmark scenario). The results reveal a 30% recovery of 98 wt % R-32 suitable for further reuse with environmental load reduction in the 86–99% range compared to the R-32 production. This study can guide the development of new F-gas recovery technologies to improve the environmental impacts of these compounds from a circular economy perspective., info:eu-repo/semantics/publishedVersion
DAU Arxiu Digital de la Universitat Ramon Llull
Publicación Artículo científico (JournalArticle)

A consistent thermodynamic molecular model of n-hydrofluoroolefins and blends for refrigeration applications, Modèle moléculaire thermodynamique cohérent des n-hydrofluoroléfines et de leurs mélanges pour des applications dans le domaine du froid

  • Llovell Ferret, Félix Lluís
  • Albà, Carlos G.
  • Vega, Lourdes F.
This work presents a thermodynamic model that characterizes 4th-generation hydrofluoroolefins (HFOs)-based refrigerants with the molecular-based soft-SAFT equation of state (Blas and Vega, 1998) as well as its application in process simulations for a selected refrigeration application. The evaluation of the HFOs has been done building on a molecular model transferred from the equivalent hydrofluorocarbons (HFCs), taking advantage of the similarities between the two chemical families. The model has been used to calculate all thermophysical properties of the selected HFOs relevant for their application as refrigerants, including the saturated density, vapor pressure, heat capacity, speed of sound, surface tension and viscosity, providing good agreement with experimental available data. In addition, phase equilibria, interfacial behavior and viscosity calculations have been performed for blends between HFCs and the two most common HFOs, R1234yf and R1234ze(E). The obtained thermodynamic properties have been used for a process simulation of a vapor compression refrigeration system, comparing the 3rd generation refrigerant R410A with these 4th generation blends, including the Coefficient of Performance for different cases, in order to establish the best alternative to R410A. Overall, this work shows how molecular modeling tools can be used now a day, as a complementary tool to generate reliable data for process simulation, in this case related to the search for alternative refrigerants.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Portable Instrumental Odour Monitoring System for Air Quality Monitoring by Citizens in Outdoor Environments

  • Palomeque-Mangut, Sergio
  • Meléndez, Félix
  • Gómez-Suarez, Jaime
  • Arroyo, Patricia
  • Santos, José Pedro
  • Lozano, Jesús
6 páginas, 6 figuras, 1 tabla, Air pollution is a major contributor to the global disease burden. Scientific literature has been consistent for the past decades, exposing the dangers behind hazardous air quality in both indoor and outdoor environments, and its impact on human health and ecosystems. Conventional monitoring stations are expensive and bulky, limiting the spatiotemporal resolution of the provided data. For this reason, administrations are interested in adding low-cost sensors to the monitoring network, and thus obtaining measures from multiple sources to enhance the network’s density and coverage. In this work, we present a portable Instrumental Odour Monitoring System (IOMS) consisting of an electronic device with an array of metal oxide semiconductor (MOS) gas and Particle Matter sensors connected through Bluetooth with a smartphone with our own developed app that gathers data and sends it to a cloud. We tested the device in two different experimental setups, the first with laboratory-controlled conditions and the second in field, creating a network with the help of volunteers in the city of Barcelona., Authors want to thank the European Union for supporting NanoSen-AQM (SOE/P1/E0569) project and volunteers from the Metropolitan Area of Barcelona for using our devices.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Performance of the IBER and HEC-HMS models for predicting peak discharge after wildfires in northwest Spain

  • Míguez, Clara
  • Novo, Ana
  • Kampf, Stephanie
  • Fernández, Cristina
9 pages, 6 tables, 5 figures, Data will be available upon reasonable request., The flooding and increased runoff that frequently occur after forest fires can have devastating impacts. Hydrological models that simulate processes in natural systems can help to predict them. In this study we measured peak discharge and time to peak in three small burned catchments in NW Spain and compared the values with corresponding estimates provided by the IBER and HECHMS models. In total, 22 events were selected for study in the three catchments, and the performance of the models was evaluated for the whole dataset and by grouping the events according to the value of the standardized precipitation index. Peak discharge was underestimated by both models, while estimates of time to peak were acceptable. The models performed better when only rainfall events with a standardized precipitation index > 0 were considered. Sensitivity analysis showed that rainfall is more influential on model predictions than curve number or roughness coefficient., This research was funded by the EU Interreg-Sudoe programme through project EPyRIS [SOE2/P5/E0811]; and the Spanish Research Agency of the Spanish Ministry of Science and Innovation through projects [ENFIRES-NW-PID2020-116494RR-C42 and TED2021-129451B-C43-IRESTORM-NW], Peer reviewed
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Origin of inverse Rashba-Edelstein effect detected at the Cu/Bi interface using lateral spin valves

  • Isasa, M.
  • Martínez-Velarte, M.C.
  • Villamor, E.
  • Magén, C.
  • Morellón, L.
  • De Teresa, J.M.
  • Ibarra, M.R.
  • Vignale, G.
  • Chulkov, E.V.
  • Krasovskii, E.E.
  • Hueso, L.E.
  • Casanova, F.
The spin transport and spin-to-charge current conversion properties of bismuth are investigated using permalloy/copper/bismuth (Py/Cu/Bi) lateral spin valve structures. The spin current is strongly absorbed at the surface of Bi, leading to ultrashort spin-diffusion lengths. A spin-to-charge current conversion is measured, which is attributed to the inverse Rashba-Edelstein effect at the Cu/Bi interface. The spin-current-induced charge current is found to change direction with increasing temperature. A theoretical analysis relates this behavior to the complex spin structure and dispersion of the surface states at the Fermi energy. The understanding of this phenomenon opens novel possibilities to exploit spin-orbit coupling to create, manipulate, and detect spin currents in two-dimensional systems.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Contribución de congreso (ConferenceOutput)

Tuning complex shapes in Pt(0) nanoparticles : from cubic dendrites to five-fold stars

  • Lacroix, L.-M.
  • Gatel, C.
  • Arenal, R.
  • Garcia, C.
  • Lachaize, S.
  • Blon, T.
  • Warot-Fonrose, B.
  • Snoeck, E.
  • Chaudret, B.
  • Viau, G.
A platinum star performance: Quasi-single-crystalline Pt nanoparticles with peculiar morphologies—cubic dendrites, planar tripods, and fivefold stars—were synthesized in high yield. Shape selectivity was achieved by finely tuning the growth kinetics under a dihydrogen atmosphere.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

CD56+/CD16- Natural Killer cells expressing the inflammatory protease granzyme A are enriched in synovial fluid from patients with osteoarthritis

  • Jaime, P.
  • García-Guerrero, N.
  • Estella, R.
  • Pardo, J.
  • García-Álvarez, F.
  • Martínez-Lostao, L.
Objective: Natural killer (NK) cells have been involved in the pathology of different inflammatory and autoimmune disorders. Inflammation is an important regulator of osteoarthritis (OA), but the molecular and cellular mechanisms regulating this process are not well defined. Design To understand the role of NK cells in OA, we have compared the phenotype (CD56 subsets and perforin and granzyme expression) and cytotoxic function of NK cells in peripheral blood and synovial fluid from patients with OA undergoing total knee arthroplasty. Results: In contrast to peripheral blood lymphocytes (PBLs), the majority of NK cells from the synovial fluid were CD56brightCD16(-) cells. As expected the expression of the cytolytic mediators perforin and granzyme B in CD56brightCD16(-) cells was low and correlated with a poor cytotoxic potential against K562 sensitive target cells. Surprisingly, this low cytotoxic NK cell subset expressed high levels of granzyme A (a protease recently characterized as a key modulator of inflammation in mouse models) in synovial fluid but not in peripheral blood. The presence of the CD56(+)brightCD16(-) cells expressing granzyme A correlated with increased levels of pro-inflammatory cytokines in synovial fluid from OA patients. Conclusion: Our results indicate that NK cells from the synovium of patients with OA, which present an immunoregulatory non-cytotoxic phenotype, show different phenotype comparing with NK cells from peripheral blood, especially expressing granzyme A, a pro-inflammatory molecule which may contribute to the establishment of chronic articular inflammation in this type of patients.
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Life Cycle Assessment of the Separation and Recycling of Fluorinated Gases Using Ionic Liquids in a Circular Economy FrameworkClick to copy article link

  • Jovell, Daniel
  • Pou, Josep Oriol
  • Llovell Ferret, Félix Lluís
  • González Olmos, Rafael
The stricter regulation regarding the use of fluorinated gases (F-gases), as a consequence of their high Global Warming Potential (GWP), represents a challenge for the refrigeration industry. The design of alternatives requires the recycling of the low to moderate GWP compounds from current refrigerant blends. However, there is not a developed and standardized technology available to recover them, and once the life cycle of the refrigeration equipment has ended, most gases are incinerated. Fluorinated ionic liquids (FILs) can effectively perform as absorbents to the complex separation of F-gas mixtures. In this work, a methodology based on the COSMO-RS thermodynamic package integrated into an Aspen Plus process simulator was used to evaluate the performance of an FIL to recover difluoromethane (R-32) from the commercial blend R-407F. The environmental sustainability of the recovery process (circular economy scenario) was analyzed with a life cycle assessment (LCA) approach, comparing the obtained results with the conventional R-32 production (benchmark scenario). The results reveal a 30% recovery of 98 wt % R-32 suitable for further reuse with environmental load reduction in the 86–99% range compared to the R-32 production. This study can guide the development of new F-gas recovery technologies to improve the environmental impacts of these compounds from a circular economy perspective., info:eu-repo/semantics/publishedVersion
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

A consistent thermodynamic molecular model of n-hydrofluoroolefins and blends for refrigeration applications, Modèle moléculaire thermodynamique cohérent des n-hydrofluoroléfines et de leurs mélanges pour des applications dans le domaine du froid

  • Llovell Ferret, Félix Lluís
  • Albà, Carlos G.
  • Vega, Lourdes F.
This work presents a thermodynamic model that characterizes 4th-generation hydrofluoroolefins (HFOs)-based refrigerants with the molecular-based soft-SAFT equation of state (Blas and Vega, 1998) as well as its application in process simulations for a selected refrigeration application. The evaluation of the HFOs has been done building on a molecular model transferred from the equivalent hydrofluorocarbons (HFCs), taking advantage of the similarities between the two chemical families. The model has been used to calculate all thermophysical properties of the selected HFOs relevant for their application as refrigerants, including the saturated density, vapor pressure, heat capacity, speed of sound, surface tension and viscosity, providing good agreement with experimental available data. In addition, phase equilibria, interfacial behavior and viscosity calculations have been performed for blends between HFCs and the two most common HFOs, R1234yf and R1234ze(E). The obtained thermodynamic properties have been used for a process simulation of a vapor compression refrigeration system, comparing the 3rd generation refrigerant R410A with these 4th generation blends, including the Coefficient of Performance for different cases, in order to establish the best alternative to R410A. Overall, this work shows how molecular modeling tools can be used now a day, as a complementary tool to generate reliable data for process simulation, in this case related to the search for alternative refrigerants.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Energy balance and environmental impact analysis of marine microalgal biomass production for biodiesel generation in a photobioreactor pilot plant

  • Sevigné Itoiz, Eva|||0000-0002-7356-4048
  • Fuentes Grunewald, Claudio|||0000-0002-3122-9452
  • Martínez Gasol, Carles|||0000-0003-3002-9229
  • Garcés, Esther|||0000-0002-2712-501X
  • Alacid, Elisabet|||0000-0003-0777-1855
  • Rossi Heras, Sergio|||0000-0003-4402-3418
  • Rieradevall, Joan|||0000-0003-3360-6829
A life cycle assessment (LCA) and an energy balance analysis of marine microalgal biomass production were conducted to determine the environmental impacts and the critical points of production for large scale planning. The artificial lighting and temperature conditions of an indoor bubble column photobioreactor (bcPBR) were compared to the natural conditions of an equivalent outdoor system. Marine microalgae, belonging to the dinoflagellate and raphidophyte groups, were cultured and the results were compared with published LCA data obtained from green microalgae (commonly freshwater algae). Among the species tested, Alexandrium minutum was chosen as the target marine microalgae for biomass production under outdoor conditions, although there were no substantial differences between any of the marine microalgae studied. Under indoor culture conditions, the total energy input for A. minutum was 923 MJ kg¯¹ vs. 139 MJ kg¯¹ for outdoor conditions. Therefore, a greater than 85% reduction in energy requirements was achieved using natural environmental conditions, demonstrating the feasibility of outdoor culture as an alternative method of bioenergy production from marine microalgae. The growth stage was identified as the principal source of energy consumption for all microalgae tested, due to the electricity requirements of the equipment, followed by the construction material of the bcPBR. The global warming category (GWP) was 6 times lower in outdoor than in indoor conditions. Although the energy balance was negative under both conditions, this study concludes with suggestions for improvements in the outdoor system that would allow upscaling of this biomass production technology for outdoor conditions in the Mediterranean.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Environmental consequences of recycling aluminum old scrap in a global market

  • Sevigné Itoiz, Eva|||0000-0002-7356-4048
  • Martínez Gasol, Carles|||0000-0003-3002-9229
  • Rieradevall, Joan|||0000-0003-3360-6829
  • Gabarrell Durany, Xavier|||0000-0003-1730-4337
For decades, aluminium recycling was a regional concern traditionally concentrated in the regions with high aluminium demand and a well-organized aluminium recycling industry. Today, however, aluminium scrap is a global raw material commodity. This change has increased the need to analyze the flows of aluminium scrap, as well as to determine the environmental consequences from aluminium recycling. The objective of this work is to determine the environmental consequences of the old scrap aluminium collection for recycling, considering the market interactions. The study focused on Spain as a representative country for Europe. We integrate material flow analysis (MFA) with consequential life cycle assessment (CLCA) in order to determine the most likely destination for the old scrap and the most likely corresponding process affected. Based on this analysis, it is possible to project some scenarios and to quantify the environmental impacts (generated and avoided) associated with aluminium recycling within a global market. From the MFA results, we projected that the demand for aluminium products will be met mainly with an increase in primary aluminium imports, and the excess of old scrap not used in Spain will be exported in future years, mainly to Asia. Depending on the marginal source of primary aluminium considered, the greenhouse gases (GHG) emission estimates varied between -17,088 kg of CO2 eq. t-1 of old scrap collected to -10,305 of CO2 eq. t-1 of old scrap collected for the global or local scenario, respectively. More GHG emissions are avoided with an increase in export flows, but the export of old scrap should be considered as the loss of a key resource, and in the long term, it will also affect the semifinished products industry. Mapping the flows of raw materials and waste, as well as quantifying the environmental impacts derived from recycling, has become an essential prerequisite to consistent development from a linear towards a circular economy.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Determination of the energy and environmental burdens associated to the biological treatment of source-separated municipal solid wastes

  • Colón Jordà, Joan|||0000-0003-1677-7239
  • Cadena, Erasmo|||0000-0003-3628-3041
  • Pognani, Michele
  • Barrena, Raquel|||0000-0002-6077-7765
  • Sánchez, Antoni|||0000-0003-4254-8528
  • Font, Xavier|||0000-0003-4981-7436
  • Artola, Adriana|||0000-0002-0524-2119
Environmental burdens of four different full-scale facilities treating source-separated organic fraction of Municipal Solid Wastes (OFMSW) have been experimentally evaluated. The studied facilities include different composting technologies and also anaerobic digestion plus composting. Home composting, as an alternative to OFMSW management, was also included in the study. Energy (electricity and diesel), water consumption and emissions of volatile organic compounds (VOC), ammonia, methane and nitrous oxide have been measured for each process. Energy consumption ranged between 235 and 870 MJ Mg OFMSW⁻¹ while the emissions of the different contaminants considered per Mg OFMSW were in the range of 0.36-8.9 kg VOC, 0.23-8.63 kg NH₃, 0.34-4.37 kg CH₄ and 0.035-0.251 kg N₂O, respectively. Environmental burdens of each facility are also analyzed from the point of view of process efficiency (i.e. organic matter stabilization degree achieved, calculated as the reduction of the Dynamic Respiration Index (DRI) of the waste treated). This study is performed through two new indices: Respiration Index Efficiency (RIE), which includes the reduction in the DRI achieved by the treatment process and Quality and Respiration Index Efficiency (QRIE), which also includes the quality of the end product. Finally, a Life Cycle Assessment is performed using the Respiration Index Efficiency (RIE) as the novel functional unit instead of the classical LCA approach based on the total mass treated.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Home and vermicomposting as sustainable options for biowaste management

  • Lleó Leida, Thais
  • Albacete, Eloisa
  • Barrena, Raquel|||0000-0002-6077-7765
  • Font, Xavier|||0000-0003-4981-7436
  • Artola, Adriana|||0000-0002-0524-2119
  • Sánchez, Antoni|||0000-0003-4254-8528
Home composting (also known as backyard composting) presents some potential benefits for the industrial treatment of the organic fraction of municipal solid waste or biowaste. Home composting avoids the collection of biowaste, reduces the impurities present in the waste being treated and, consequently, in the resulting compost, and theoretically decreases the material and energy needs of the process. However, self-composting requires a composting bin and pruning waste as bulking material as well as space in a garden or on a roof that is not always available. An alternative for the self-management of biowaste is vermicomposting, which requires less space and no bulking material. Both the home composting and vermicomposting methods were studied over an eight-month period to determine the quality of the compost produced, the capacity of the methodology and the resulting gaseous emissions. The treatment capacity of the composters used in this work was determined on a weekly basis. The vermicomposter had a treatment capacity of 50 g biowaste per L, whereas the home composter had a treatment capacity of 16 g biowaste per L. The home composter required the addition of 6.3 g of bulking agent per L of composter. The quality of the final product, compost, was similar in both cases, with each batch of compost having low metal content and a high degree of stability, with Dynamic Respiration Indices of 0.43 and 0.89 mg O2 g⁻¹ Organic Matter h⁻¹ for compost and vermicompost, respectively. Gaseous emissions from home composters show the presence of 1.3 kg NH₃ Mg⁻¹ biowaste and 1.35 kg CH₄ Mg⁻¹ biowaste, values that are within the range reported in the literature for home and industrial composting, although N2O emissions, 1.16 kg Mg⁻¹ biowaste, were higher. Gaseous emissions from the vermicomposters were lower than from the home composters: 3.33 × 10⁻³, 2.19 × 10⁻³ and 3.66 × 10⁻³ kg of pollutant Mg⁻¹ biowaste for NH₃, CH₄ and volatile organic compounds, respectively. No odours were detected for either system. Home and vermicomposting can be considered suitable alternatives to divert a portion of the biowaste from the traditional waste-management system.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Home composting versus industrial composting, influence of composting system on compost quality with focus on compost stability

  • Barrena, Raquel|||0000-0002-6077-7765
  • Font, Xavier|||0000-0003-4981-7436
  • Gabarrell Durany, Xavier|||0000-0003-1730-4337
  • Sánchez, Antoni|||0000-0003-4254-8528
Stability is one of the most important properties of compost obtained from the organic fraction of municipal solid wastes. This property is essential for the application of compost to land to avoid further field degradation and emissions of odors, among others. In this study, a massive characterization of compost samples from both home producers and industrial facilities is presented. Results are analyzed in terms of chemical and respiration characterizations, the latter representing the stability of the compost. Results are also analyzed in terms of statistical validation. The main conclusion from this work is that home composting, when properly conducted, can achieve excellent levels of stability, whereas industrial compost produced in the studied facilities can also present a high stability, although an important dispersion is found in these composts. The study also highlights the importance of respiration techniques to have a reliable characterization of compost quality, while the chemical characterization does not provide enough information to have a complete picture of a compost sample.