Pasar al contenido principal

E-NANOSCOPIAS Y HETERO-MULTICAPAS PARA DISPOSITIVOS Y SISTEMAS TANDEM BASADOS EN NANOESTRUCTURAS PARA TRANSFORMACION DE LA ENERGIA SOLAR EN COMBUSTIBLES SOLARES

MAT2014-59961-C2-2-R

•
Nombre agencia financiadora Ministerio de Economía y Competitividad
Acrónimo agencia financiadora MINECO
Programa Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Convocatoria Proyectos I+D+i Retos de Investigación
Año convocatoria 2014
Plan Estatal 2013-2016 Plan Estatal de Investigación Científica y Técnica y de Innovación
Unidad de gestión Secretaría de Estado de Educación, Formación Profesional y Universidades
Centro beneficiario FUNDACIÓ INSTITUT CATALÀ DE NANOCIÈNCIA I NANOTECNOLOGIA
Identificador persistente http://dx.doi.org/10.13039/501100003329

Resultados relacionados

Resultados totales (Incluyendo duplicados): 35
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Enhanced activity and acid pH stability of prussian blue-type oxygen evolution electrocatalysts processed by chemical etching

  • Han, Li-Juan
  • Morante, Joan Ramón
  • Arbiol, Jordi
  • Galán-Mascarós, José Ramón
et al., The development of upscalable oxygen evolving electrocatalysts from earth-abundant metals able to operate in neutral or acidic environments and low overpotentials remains a fundamental challenge for the realization of artificial photosynthesis. In this study, we report a highly active phase of heterobimetallic cyanide-bridged electrocatalysts able to promote water oxidation under neutral, basic (pH < 13), and acidic conditions (pH > 1). Cobalt-iron Prussian blue-type thin films, formed by chemical etching of Co(OH)(CO)·nHO nanocrystals, yield a dramatic enhancement of the catalytic performance toward oxygen production, when compared with previous reports for analogous materials. Electrochemical, spectroscopic, and structural studies confirm the excellent performance, stability, and corrosion resistance, even when compared with state-of-the-art metal oxide catalysts under moderate overpotentials and in a remarkably large pH range, including acid media where most cost-effective water oxidation catalysts are not useful. The origin of the superior electrocatalytic activity toward water oxidation appears to be in the optimized interfacial matching between catalyst and electrode surface obtained through this fabrication method., This work was supported by the European Union (Project ERC StG Grant CHEMCOMP No. 279313); the Spanish Ministerio de Economia y Competitividad (MINECO) through Projects CTQ2015-71287-R, TNT-FUELS, and e-TNT (MAT2014-59961-C2-2-R) and the Severo Ochoa Excellence Accreditations 2014−2018, SEV-2013-0319 and SEV-2013-0295, the Generalitat de Catalunya (2014-SGR-797 and 2014-SGR1638), and the ICIQ foundation. A.R.C. thanks the Marie Curie COFUND Action from the European Commission for cofinancing his postdoctoral fellowship. L.H. thanks MINECO for her predoctoral fellowship. The research leading to these results has also received funding from “La Caixa” Foundation., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Mn3O4@CoMn2O4-CoxOy nanoparticles: partial cation exchange synthesis and electrocatalytic properties toward the oxygen reduction and evolution reactions

  • Luo, ZhiShan
  • Ibáñez, María
  • Nafria, Raquel
  • Martí-Sànchez, Sara
  • Genç, Aziz
  • Mata, Maria de la
  • Arbiol, Jordi
  • Morante, Joan Ramón
  • Cabot, Andreu
et al., MnO@CoMnO nanoparticles (NPs) were produced at low temperature and ambient atmosphere using a one-pot two-step synthesis protocol involving the cation exchange of Mn by Co in preformed MnO NPs. Selecting the proper cobalt precursor, the nucleation of CoO crystallites at the MnO@CoMnO surface could be simultaneously promoted to form MnO@CoMnO-CoO NPs. Such heterostructured NPs were investigated for oxygen reduction and evolution reactions (ORR, OER) in alkaline solution. MnO@CoMnO-CoO NPs with [Co]/[Mn] = 1 showed low overpotentials of 0.31 V at -3 mA·cm and a small Tafel slope of 52 mV·dec for ORR, and overpotentials of 0.31 V at 10 mA·cm and a Tafel slope of 81 mV·dec for OER, thus outperforming commercial Pt-, IrO-based and previously reported transition metal oxides. This cation-exchange-based synthesis protocol opens up a new approach to design novel heterostructured NPs as efficient nonprecious metal bifunctional oxygen catalysts., This work was supported by the European Regional Development Funds and the Spanish MINECO projects BOOSTER (ENE2013-46624-C4-3-R), TNT-FUELS (MAT2014-59961), e-TNT (MAT2014-59961-C2-2-R) and PEC-CO2 (ENE2012-3651). Z.L. and Y.L. thank the China Scholarship Council for scholarship support. E.I. thanks AGAUR for his Ph.D. grant (FI-2013-B-00769). M.I. thanks AGAUR for the Beatriu de Pinos postdoctoral grant (2013 BP-A00344). S.M. acknowledges funding from “Programa Internacional de Becas ‘la Caixa’-Severo Ochoa”. J.L. is a Serra Hunter Fellow and is grateful to ICREA Academia program. We also acknowledge the funding from Generalitat de Catalunya 2014 SGR 1638., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Orientationally ordered silicon nanocrystal cuboctahedra in superlattices

  • Yu, Yixuan
  • Mata, Maria de la
  • Arbiol, Jordi
  • Korgel, Brian A.
This is an open access article published under an ACS AuthorChoice License.-- et al., Uniform silicon nanocrystals were synthesized with cuboctahedral shape and passivated with 1-dodecene capping ligands. Transmission electron microscopy, electron diffraction, and grazing incidence wide-angle and small-angle X-ray scattering show that these soft cuboctahedra assemble into face-centered cubic superlattices with orientational order. The preferred nanocrystal orientation was found to depend on the orientation of the superlattices on the substrate, indicating that the interactions with the substrate and assembly kinetics can influence the orientation of faceted nanocrystals in superlattices., This research was funded by the Robert A. Welch Foundation (Grant F-1464 and F-1696) and the National Science Foundation (Grant CBET-1403768). CHESS is supported by the NSF & NIH/NIGMS via NSF award DMR-1332208. J.A. and M.d.l.M. acknowledge funding from Generalitat de Catalunya 2014 SGR 1638 and MINECO projects MAT2014-59961-C2-2-R and Severo Ochoa Program (Grant SEV-2013-0295)., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Pd2Sn [010] nanorods as a highly active and stable ethanol oxidation catalyst

  • Luo, ZhiShan
  • Lu, Jianmin
  • Flox, Cristina
  • Nafria, Raquel
  • Genç, Aziz
  • Arbiol, Jordi
  • Ibáñez, María
  • Morante, Joan Ramón
  • Cabot, Andreu
The development of highly active, low cost and stable electrocatalysts for direct alcohol fuel cells remains a critical challenge. While PdSn has been reported as an excellent catalyst for the ethanol oxidation reaction (EOR), here we present DFT analysis results showing the (100) and (001) facets of orthorhombic PdSn to be more favourable for the EOR than (010). Accordingly, using tri-n-octylphosphine, oleylamine (OLA) and methylamine hydrochloride as size and shape directing agents, we produced colloidal PdSn nanorods (NRs) grown in the [010] direction. Such PdSn NRs, supported on graphitic carbon, showed excellent performance and stability as an anode electrocatalyst for the EOR in alkaline media, exhibiting 3 times and 10 times higher EOR current densities than that of PdSn and Pd nanospheres, respectively. We associate this improved performance with the favourable faceting of the NRs., This work was supported by the European Regional Development Funds and the Spanish MINECO project BOOSTER, and PEC-CO2. ZL thanks the China Scholarship Council for scholarship support. MI thanks AGAUR for Beatriu de Pinos postdoctoral grant (2013 BP-A00344). JL is a Serra Hunter Fellow and is grateful to the ICREA Academia program. The authors also acknowledge the funding from Generalitat de Catalunya 2014 SGR 1638. ICN2 acknowledges support from the Severo Ochoa Program (MINECO, Grant SEV-2013-0295). AG and JA acknowledge funding from the Spanish MINECO coordinated projects between IREC and ICN2 TNT-FUELS and e-TNT (MAT2014-59961-C2)., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Synergistic effects in 3D honeycomb-like hematite nanoflakes/branched polypyrrole nanoleaves heterostructures as high-performance negative electrodes for asymmetric supercapacitors

  • Tang, Peng-Yi
  • Han, Li-Juan
  • Genç, Aziz
  • Galán-Mascarós, José Ramón
  • Morante, Joan Ramón
  • Arbiol, Jordi
et al., Rational assembly of unique branched heterostructures is one of the facile techniques to improve the electrochemical figure of merit of materials. By taking advantages of hydrogen bubbles dynamic template, hydrothermal method and electrochemical polymerization, branched polypyrrole (PPy) nanoleaves decorated honeycomb-like hematite nanoflakes (core-branch FeO@PPy) are fabricated. X-ray diffraction, X-ray photoelectron spectroscopy, scanning electron microscopy, transmission electron microscopy (TEM), high-resolution TEM, and scanning transmission electron microscopy in high angle annular dark field mode with electron energy loss spectroscopy were combined to elucidate the mechanisms underlying formation and morphogenesis evolution of core-branch FeO@PPy heterostructures. Benefiting from the stability of honeycomb-like hematite nanoflakes and the high conductivity of PPy nanoleaves, the resultant core-branch FeO@PPy exhibits an ultrahigh capacitance of 1167.8 F g at 1 A g in 0.5 M NaSO aqueous solution. Moreover, the assembled bi-metal oxides asymmetric supercapacitor (FeO@PPy//MnO) gives rise to a maximum energy density of 42.4 W h kg and a maximum power density of 19.14 kW kg with an excellent cycling performance of 97.1% retention after 3000 cycles at 3 A g. These performance features are superior than previous reported iron oxide/hydroxides based supercapacitors, offering an important guideline for future design of advanced next-generation supercapacitors., We acknowledge the funding from Generalitat de Catalunya 2014 SGR 1638, 2014 SGR 797 and MINECO coordinated projects between IREC and ICN2 TNT-FUELS and e-TNT (MAT2014-59961-C2-2-R). Xuan Zhang is grateful for financial support from China Scholarship Council. Part of the present work has been performed in the framework of Universitat Autònoma de Barcelona Materials Science PhD program., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

The ethylhexanoate route to metal oxide nanocrystals: Synthesis of CoO nanooctahedra from CoII2-ethylhexanoate

  • Epifani, Mauro
  • Tang, Peng-Yi
  • Genç, Aziz
  • Arbiol, Jordi
  • Díaz, Raül
  • Wicker, Susanne
CoO nanocrystals were prepared by solvothermal processing of Co 2-ethylhexanoate in oleylamine at 250 °C. The obtained products, identified as CoO by X-ray diffraction, had an octahedral shape, as seen by transmission electron microscopy, reflecting the cubic symmetry of the CoO crystallographic phase. The materials were converted into the CoOphase after heat treatment at 400 °C. The nanocrystal evolution was investigated by FTIR spectroscopy. It was concluded that weak oleylamine bonding to the nanocrystal surface during the synthesis step favored the exchange with 2-ethylhexanoato ligands, and that the interplay between the two ligands favored the kinetic control of the growth, resulting in the finally observed octahedral morphology. The CoOphase obtained from the heat treatment at 400 °C was used to process chemoresistive sensors, which were able to detect ethanol under dry and humid conditions (0 and 50 % r.h. HO at 25 °C) at low temperatures (100 °C)., Funding is acknowledged from the Generalitat de Catalunya (2014 SGR 1638) and the Spanish Ministry of Economy and Competitiveness (MINECO) coordinated projects between the Catalonia Institute for Energy Research (IREC), the Catalan Institute of Nanoscience and Nanotechnology (ICN2) (TNT-FUELS, eTNT) (MAT2014-59961-C2-2-R), and the Severo Ochoa Excellence Program., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Low-temperature growth of axial Si/Ge nanowire heterostructures enabled by trisilane

  • Hui, Ho Yee
  • Mata, Maria de la
  • Arbiol, Jordi
  • Filler, Michael A.
Axial Si/Ge heterostructure nanowires, despite their promise in applications ranging from electronics to thermal transport, remain notoriously difficult to synthesize. Here, we grow axial Si/Ge heterostructures at low temperatures using a Au catalyst with a combination of trisilane and digermane. This approach yields, as determined with detailed electron microscopy characterization, arrays of epitaxial Si/Ge nanowires with excellent morphologies and purely axial composition profiles. Our data indicate that heterostructure formation can occur via the vapor-liquid-solid or vapor-solid-solid mechanism. These findings highlight the importance of precursor chemistry in semiconductor nanowire synthesis and open the door to Si/Ge nanowires with programmable quantum domains., M.A.F. and H.Y.H. gratefully acknowledge the financial support of the National Science Foundation (1133563 and 1150755). H.Y.H. also thanks the Archibald McNeill Endowment at Georgia Tech and the Institute for Electronics and Nanotechnology (IEN) for additional support. J.A. and M.d.l.M. also acknowledge funding from Generalitat de Catalunya 2014 SGR 1638, the Spanish MINECO ICN2 Severo Ochoa Excellence Program (Grant SEV-2013-0295), and e-TNT (MAT2014-59961-C2-2-R)., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Contribución de congreso (ConferenceOutput)

Combined TEM/STEM and in-situ c-AFM characterization of 2D nanoflake-like heterostructures for energy storage and conversion applications

  • Tang, Peng-Yi
  • Mata, Maria de la
  • Han, Li-Juan
  • Verdaguer, Albert
  • Genç, Aziz
  • Zhang, Xuan
  • Galán-Mascarós, José Ramón
  • Morante, Joan Ramón
  • Arbiol, Jordi
Resumen del póster presentado al 16th European Microscopy Congress, celebrado en Lyon (Francia) del 28 de agosto al 2 de septiembre de 2016.-- et al., Honeycomb-like hematite nanoflakes/branched polypyrrole nanoleaves heterostructures with a 3D complex structure have been synthesized and employed as high-performance negative electrodes for asymmetric supercapacitors application. The detailed TEM-STEM characterization and deep EELS chemical analysis at the nanoscale has been combined to elucidate the mechanisms underlying the formation and morphology evolution of core-branch Fe2O3@PPy heterostructures.[1] In addition, we have studied the mechanism of converting MoO2 nanoflakes into 2D free-standing MoS2 electrode by sulfurization process for water splitting. In this way, the atomic resolution aberration corrected HAADF STEM reveals the sulfurization mechanism in an unprecedented detail, together with EELS chemical maps. Furthermore, in-situ electrical measurements have been performed by means of c-AFM on the MoO2/MoS2 nanoflakes surfaces in order to detect their electronic active sites., We acknowledge the funding from Generalitat de Catalunya 2014 SGR 1638, 2014 SGR 797 and MINECO coordinated projects between IREC and ICN2 TNT-FUELS and e-TNT (MAT2014-59961-C2-2-R). Xuan Zhang is grateful for financial support from China Scholarship Council. Part of the present work has been performed in the framework of Universitat Autònoma de Barcelona Materials Science PhD program., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Contribución de congreso (ConferenceOutput)

Structural and chemical characterization and 3D modelling of metal oxide core-shell nanoparticles with complex morphology

  • Martí-Sànchez, Sara
  • Genç, Aziz
  • Luo, ZhiShan
  • Ibáñez, María
  • Mata, Maria de la
  • Cabot, Andreu
  • Arbiol, Jordi
Resumen del póster presentado al 16th European Microscopy Congress, celebrado en Lyon (Francia) del 28 de agosto al 2 de septiembre de 2016., A wide variety of metal oxide manganite and ferrite core-shell nanoparticles (NPs) with adjustable composition were characterized by means of Transmission Electron Microscopy related tools in order to precisely understand their composition, the arrangement of the different chemical species and cation valence state variation along the nanoparticles. The nanoparticles were produced at low temperature and ambient atmosphere using a one-pot two-step synthesis protocol involving the cation exchange of Mn or Fe by Co or Ni in preformed Mn3O4 or Fe3O4 NPs, allowing the formation of a core shell structure. These nanoparticle systems present a complex 3D structure, which has been modelled with Rhodius software and simulated with the STEM-CELL packages, giving rise to a fine determination of the studied systems. Special attention has been paid on manganite – cobalt systems. By selecting the proper cobalt precursor, CoO crystallites could be simultaneously nucleated on the NP surface to form Mn3O4@CoMn2O4–CoO (Figure 1). In this latest case, heterostructured NPs exhibited improved performance and durability as bifunctional catalysts for the oxygen reduction and evolution reactions (ORR, OER) over commercial Pt and IrO2-based catalysts and over previously reported spinel electrocatalysts in alkaline solution., SM acknowledges funding from >Programa Internacional de Becas >la Caixa>-Severo Ochoa”, from Generalitat de Catalunya 2014 SGR 1638, the Spanish MINECO MAT2014-51480-ERC (e-ATOM), Severo Ochoa Excellence Program and coordinated projects between IREC and ICN2, TNT-FUELS and e-TNT (MAT2014-59961-C2-2-R). Part of the present work has been performed in the framework of Universitat Autònoma de Barcelona Materials Science PhD program., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Passivation layers for nanostructured photoanodes: ultra-thin oxides on InGaN nanowires

  • Neuderth, Paula
  • Coll, Mariona
  • Eickhoff, Martin
Neuderth, Paula et al., An experimental strategy for systematically assessing the influence of surface passivation layers on the photocatalytic properties of nanowire photoanodes by combining photocurrent analysis, photoluminescence spectroscopy and high resolution transmission electron microscopy with a systematic variation of sample structure and the surrounding electrolyte is demonstrated. Following this approach we can separate the impact on recombination and transport processes of photogenerated carriers. We apply this strategy to analyze the influence of ultra-thin TiO2, CeO2 and Al2O3 coatings deposited by atomic layer deposition on the photoelectrochemical performance of InxGa1−xN/GaN nanowire (NW) photoelectrodes. The passivation of surface states results in an increase of the anodic photocurrent (PC) by a factor of 2.5 for the deposition of 5 nm TiO2. In contrast, the PC is reduced for CeO2- and Al2O3-coated NWs due to enhanced defect recombination in the passivation layer or increased band discontinuities. Furthermore, photoelectrochemical oxidation of the InxGa1−xN/GaN NW photoelectrode is attenuated by the TiO2 layer and completely suppressed for a layer thickness of 7 nm or more. Due to efficient charge transfer from the InxGa1−xN NW core a stable TiO2-covered photoanode with visible light excitation is realized., Financial support is provided by the DFG via the GrK (Research training group) 2204 “Substitute Materials for sustainable Energy Technologies.” MC thanks Ram ́on y Cajal program RYC- 2013-12448. We also acknowledge nancial support from the Spanish Ministry of Economy and Competitiveness, through the “Severo Ochoa” Programme for Centres of Excellence in R&D (SEV-2015-0496). This article is based upon work from COST Action MP1402 “Hooking together European research in atomic layer deposition (HERALD)”, supported by COST (European Cooperation in Science and Technology). SMS acknowledges funding from “Programa Internacional de Becas “la Caixa”- Severo Ochoa”. JA, MdlM. and SMS also acknowledge funding from Generalitat de Catalunya 2014 SGR 1638 and the Spanish MINECO e-TNT (MAT2014-59961-C2-2-R). ICN acknowledges support from the Severo Ochoa Program (MINECO, Grant SEV- 2013-0295) and is funded by the CERCA Programme/Generalitat de Catalunya. The atomic resolution HAADF-STEM microscopy was conducted in the Laboratorio de Microscopias Avanzadas at the Instituto de Nanociencia de Aragon-Universidad de Zaragoza. JA and SMS thank them for offering access to their instruments and expertise. Part of the present work has been performed in the framework of Universitat Aut`onoma de Bar- celona Materials Science PhD program. RM gratefully acknowledges funding in the Emmy-Noether program (MA 5392/3-1) of the German Research Foundation DFG., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Growth and luminescence of polytypic InP on epitaxial graphene

  • Mukherjee, Samik
  • Nateghi, Nima
  • Jacobberger, Robert M.
  • Bouthillier, Etienne
  • Mata, Maria de la
  • Arbiol, Jordi
  • Coenen,Toon
  • Cardinal, Dhan
  • Levesque, Pierre
  • Desjardins, Patrick
  • Martel, Richard
  • Arnold, Micheal S.
  • Moutanabbir, Oussama
Van der Waals epitaxy is an attractive alternative to direct heteroepitaxy where the forced coherency at the interface cannot sustain large differences in lattice parameters and thermal expansion coefficients between the substrate and the epilayer. Herein, the growth of monocrystalline InP on Ge and SiO2/Si substrates using graphene as an interfacial layer is demonstrated. Micrometer‐sized InP crystals are found to grow with interfaces of high crystalline quality and with different degrees of coalescence depending on the growth conditions. Some InP crystals exhibit a polytypic structure, consisting of alternating zinc‐blende and wurtzite phases, forming a type‐II homojunction with well (barrier) width of about 10 nm. The optical properties, investigated using room temperature nano‐cathodoluminescence, indicate the signatures of the direct optical transitions at 1.34 eV across the gap of the zinc‐blende phase and the indirect transitions at ≈1.31 eV originating from the alternating zinc‐blende and wurtzite phases. Additionally, the InP nanorods, found growing mainly on the graphene/SiO2/Si substrate, show optical transition across the gap of the wurtzite phase at ≈1.42 eV. This demonstration of InP growth on graphene and the correlative study between the structure and optical properties pave the way to develop hybrid structures for potential applications in integrated photonic and optoelectronic devices., J.A. and M.d.l.M. acknowledge funding from the Generalitat de Catalunya 2014 SGR 1638 and the Spanish MINECO project e‐TNT (MAT2014‐59961‐C2‐2‐R). ICN2 acknowledges support from the Severo Ochoa Program (MINECO, Grant SEV‐2013‐0295). O.M. acknowledges support from the NSERC‐Canada (Discovery Grants and Strategic Partnership Grants), the Canada Foundation for Innovation, the MRIF Québec (Coopération Québec‐Catalogne), and the Canada Research Chair. R.M.J. and M.S.A. acknowledges the support by the U.S. Department of Energy, Office of Science, Basic Energy Sciences, under Award # DE‐SC0016007. P.D. and R.M. acknowledge financial support from the NSERC., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Growth of Au–Pd2Sn nanorods via galvanic replacement and their catalytic performance on hydrogenation and sonogashira coupling reactions

  • Nafria, Raquel
  • Luo, ZhiShan
  • Ibáñez, María
  • Martí-Sànchez, Sara
  • Yu, Xiaoting
  • Mata, Maria de la
  • Llorca, Jordi
  • Arbiol, Jordi
  • Kovalenko, Maksym V.
  • Grabulosa, Arnald
  • Muller, Guillermo
  • Cabot, Andreu
Colloidal Pd2Sn and Au–Pd2Sn nanorods (NRs) with tuned size were produced by the reduction of Pd and Sn salts in the presence of size- and shape-controlling agents and the posterior growth of Au tips through a galvanic replacement reaction. Pd2Sn and Au–Pd2Sn NRs exhibited high catalytic activity toward quasi-homogeneous hydrogenation of alkenes (styrene and 1-octene) and alkynes (phenylacetylene and 1-octyne) in dichloromethane. Au–Pd2Sn NRs showed higher activity than Pd2Sn for 1-octene, 1-octyne, and phenylacetylene. In Au–Pd2Sn heterostructures, X-ray photoelectron spectroscopy evidenced an electron donation from the Pd2Sn NR to the Au tips. Such heterostructures showed distinct catalytic behavior in the hydrogenation of compounds containing a triple bond such as tolan. This can be explained by the aurophilicity of triple bonds. To further study this effect, Pd2Sn and Au–Pd2Sn NRs were also tested in the Sonogashira coupling reaction between iodobenzene and phenylacetylene in N,N-dimethylformamide. At low concentration, this reaction provided the expected product, tolan. However, at high concentration, more reduced products such as stilbene and 1,2-diphenylethane were also obtained, even without the addition of H2. A mechanism for this unexpected reduction is proposed., This work was supported by the European Regional Development Funds and the Spanish MINECO projects ENE2013-46624-C4-3-R, MAT2014-59961-C2-2-R, and CTQ2015-65040-P. Z.L. and X.Y. thanks the China Scholarship Council for scholarship support. M.I. thanks AGAUR for Beatriu de Pinós postdoctoral grant (2013 BP-A00344). J.L. is Serra Húnter Fellow and is grateful to ICREA Academia program. Authors also acknowledge the funding from Generalitat de Catalunya 2014 SGR 1638. S.M.-S. acknowledges funding from “Programa Internacional de Becas “la Caixa—Severo Ochoa”. ICN2 acknowledges support from the Severo Ochoa Program (MINECO, Grant SEV-2013-0295)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Tailoring copper foam with silver dendrite catalysts for highly selective carbon dioxide conversion into carbon monoxide

  • Urbain, Félix
  • Tang, Peng-Yi
  • Carretero, Nina M.
  • Andreu, Teresa
  • Arbiol, Jordi
  • Morante, Joan Ramón
The present study outlines the important steps to bring electrochemical conversion of carbon dioxide (CO2) closer to commercial viability by using a large-scale metallic foam electrode as a highly conductive catalyst scaffold. Because of its versatility, it was possible to specifically tailor three-dimensional copper foam through coating with silver dendrite catalysts by electrodeposition. The requirements of high-yield CO2 conversion to carbon monoxide (CO) were met by tuning the deposition parameters toward a homogeneous coverage of the copper foam with nanosized dendrites, which additionally featured crystallographic surface orientations favoring CO production. The presented results evidence that Ag dendrites, owing a high density of planes with stepped (220) surface sites, paired with the superior active surface area of the copper foam can significantly foster the CO productivity. In a continuous flow-cell reactor setup, CO Faradaic efficiencies reaching from 85 to 96% for a wide range of low applied cathode potentials (<1.0 VRHE) along with high CO current densities up to 27 mA/cm2 were achieved, far outperforming other tested scaffold materials. Overall, this research provides new strategic guidelines for the fabrication of efficient and versatile cathodes for CO2 conversion compatible with large-scale integrated prototype devices., Authors acknowledge funding from Generalitat de Catalunya through the CERCA program, 2017 SGR 1246, 2017 SGR 327 and the Spanish MINECO projects MAT2014-59961, ENE2016-80788-C5-5-R and ENE2017-85087, together with the support from REPSOL S.A. ICN2 acknowledges the support from the Severo Ochoa Programme (grant no. SEV2017-0706). F.U. acknowledges the financial support from MINECO through Juan de la Cierva fellowship (FJCI-2016-29147)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Ultrasensitive binder-free glucose sensors based on the pyrolysis of in situ grown Cu MOF

  • Zhang, Xuan
  • Luo, Jiangshui
  • Tang, Peng-Yi
  • Morante, Joan Ramón
  • Arbiol, Jordi
  • Xu, Cailing
  • Li,Qingfeng
  • Fransaer, Jan
A non-enzymatic glucose sensor based on carbon/Cu composite materials was developed by the in-situ growth and subsequent pyrolysis of metal-organic frameworks (MOFs) on Cu foam. After pyrolysis, SEM, HRTEM and STEM-EELS were employed to clarify the hierarchical Cu@porous carbon electrode. It is found that the Cu nanoparticles are uniformly embedded in the carbon matrix, carbon matrix in close contact with the pyrolized carbon sheets. The electrocatalytic activity of the Cu@porous carbon matrix electrode for glucose sensing was explored by cyclic voltammetry (CV) and chronoamperometry. The resulting Cu@porous carbon matrix electrode displays ultrahigh sensitivity (10.1 mA cm−2 mM−1), low detection limit (0.6 μM), short response time (less than 2 s) and good stability, indicating that the developed electrode is a promising glucose sensor., X. Zhang is grateful to China Scholarship Council. Financial support from “China Fund” KU Leuven (ISP/13/02SJT) is acknowledged. J. Luo acknowledges the Research Foundation – Flanders (FWO) for a FWO Postdoctoral Fellowship (12F5514N), a Research Grant (1529816N) and a travel grant (V410316N) for a Visiting Professorship at the Technical University of Denmark. C. L. Xu thanks the National Natural Science Foundation of China (No. 21673105) and the Fundamental Research Funds for the Central Universities (lzujbky-2016-k09). JA, PYT and JRM acknowledge funding from Generalitat de Catalunya 2014 SGR 1638 and the Spanish MINECO coordinated projects between IREC and ICN2 TNT-FUELS and e-TNT (MAT2014-59961-C2-2-R). ICN2 acknowledges support from the Severo Ochoa Program (MINECO, Grant SEV-2013-0295) and is funded by the CERCA Programme / Generalitat de Catalunya. Part of the present work has been performed in the framework of Universitat Autonoma de Barcelona Materials Science Ph.D. program. Funding from “Minjiang Scholar” Program and key project (No. JZ160480) of Department of Education, Fujian Province, China is also acknowledged., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Multilayered hematite nanowires with thin‐film silicon photovoltaics in an all‐earth‐abundant hybrid tandem device for solar water splitting

  • Urbain, Félix
  • Tang, Peng-Yi
  • Smirnov, Vladimir
  • Welter, Katharina
  • Andreu, Teresa
  • Finger, Friedhelm
  • Arbiol, Jordi
  • Morante, Joan Ramón
The concept of hybrid tandem device structures that combine metal oxides with thin‐film semiconducting photoabsorbers holds great promise for large‐scale, robust, and cost‐effective bias‐free photoelectrochemical water splitting (PEC‐WS). This work highlights important steps toward the efficient coupling of high‐performance hematite photoanodes with multijunction thin‐film silicon photocathodes providing high bias‐free photocurrent density. The hybrid PEC‐WS device is optimized by testing three types of multijunction silicon photocathodes with the hematite photoanode: amorphous silicon (a‐Si:H) tandem: a‐Si:H/a‐Si:H and triple junction with microcrystalline silicon (μc‐Si:H): a‐Si:H/a‐Si:H/μc‐Si:H and a‐Si:H/μc‐Si:H/μc‐Si:H. The results provide evidence that the multijunction structures offer high flexibility for hybrid tandem devices with regard to tunable photovoltages and spectral matching. Furthermore, both photoanode and photocathode are tested under various electrolyte and light concentration conditions, respectively, with respect to their photoelectrochemical performance and stability. A 27 % enhancement in the solar‐to‐hydrogen conversion efficiency is observed upon concentrating light from 100 to 300 mW cm−2. Ultimately, bias‐free water splitting is demonstrated, with a photocurrent density of 4.6 mA cm−2 (under concentrated illumination) paired with excellent operation stability for more than 24 h of the all‐earth‐abundant and low‐cost hematite/silicon tandem PEC‐WS device., The authors acknowledge funding from Generalitat de Catalunya through the CERCA program, 2017 SGR 1246, 2017 SGR 327 and the Spanish MINECO projects MAT2014‐59961, ENE2016‐80788‐C5‐5‐R and ENE2017‐85087, together with the support from REPSOL, S. A. ICN2 is supported by the Severo Ochoa program from Spanish MINECO (Grant No. SEV‐2017‐0706). IREC also acknowledges additional support from the European Regional Development Funds (ERDF, FEDER), (S)TEM part of the present work has been performed in the framework of Universitat Autònoma de Barcelona Materials Science PhD program and the rest in the Nanoscience program of the University of Barcelona. The authors thank S. Moll (IEK‐5), M. Biset‐Peiró (IREC), and H. Xie (IREC) for their contribution to this work. F.U. acknowledges financial support from MINECO through Juan de la Cierva fellowship (FJCI‐2016–29147).V.S., K.W., and F.F. (authors from IEK‐5) thank the Deutsche Forschungsgemeinschaft (DFG) (Priority Program SPP 1613)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Effects of solar irradiation on thermally driven CO2 methanation using Ni/CeO2–based catalyst

  • Golovanova, Viktoria
  • Spadaro, Maria Chiara
  • Arbiol, Jordi
  • Golovanova, Liubov V.
  • Rantala, Tapio T.
  • Andreu, Teresa
  • Morante, Joan Ramón
Utilization of the renewable energy sources is one of the main challenges in the state-of-the-art technologies for CO recycling. Here we have taken advantage of the solar light harvesting in the thermocatalytic approach to carbon dioxide methanation. The large-surface-area Ni/CeO catalyst produced by a scalable low-cost method was characterized and tested in the dark and under solar light irradiation conditions. Light-assisted CO conversion experiments as well as in-situ DRIFT spectrometry, performed at different illumination intensities, have revealed a dual effect of the incident photons on the catalytic properties of the two-component Ni/CeO catalyst. On the one hand, absorbed photons induce a localized surface plasmon resonance in the Ni nanoparticles followed by dissipation of the heat to the oxide matrix. On the other hand, the illumination activates the photocatalytic properties of the CeO support, which leads to an increase in the concentration of the intermediates being precursor for methane production. Analysis of the methane production at different temperatures and illumination conditions has shown that the methanation reaction in our case is controlled by a photothermally-activated process. The used approach has allowed us to increase the reaction rate up to 2.4 times and consequently to decrease the power consumption by 20 % under solar illumination, thus replacing the conventional thermal activation of the reaction with a green energy source., This work has been done in the framework of the doctorate programme in Materials Science of the Autonomous University of Barcelona. V. Golovanova has received funding from the European Union’s Horizon 2020 research and innovation programme under the Marie Skłodowska-Curie grant agreement No 754397. Authors acknowledge Generalitat de Catalunya for financial support through the CERCA Programme, M2E (2017 SGR 1246) and the CSC – IT Center for Science, Espoo, Finland for provided resources. IREC also acknowledges additional support by the European Regional Development Funds (ERDF, FEDER) and by MINECO coordinated projects MAT2014-59961-C2, ENE2016-80788-C5-5-R and ENE2017-85087-C3. M. C. Spadaro and J. Arbiol acknowledge funding from Generalitat de Catalunya 2017 SGR 327. ICN2 is supported by the Severo Ochoa programme from Spanish MINECO (Grant No. SEV-2017-0706) and is funded by the CERCA Programme / Generalitat de Catalunya. M. C. Spadaro has received funding from the European Union’s Horizon 2020 research and innovation programme under the Marie Skłodowska-Curie grant agreement No. 754510 (PROBIST) and the Severo Ochoa programme.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Towards defect-free 1-D GaAs/AlGaAs heterostructures based on GaAs nanomembranes

  • Tutuncuoglu, Gozde
  • Mata, María de la
  • Deiana, D
  • Potts, Heidi
  • Matteini, Federico
  • Arbiol, Jordi
  • Fontcuberta Morral, Anna
We demonstrate the growth of defect-free zinc-blende GaAs nanomembranes by molecular beam epitaxy. Our growth studies indicate a strong impact of As4 re-emission and shadowing in the growth rate of the structures. The highest aspect ratio structures are obtained for pitches around 0.7-1 μm and a gallium rate of 1 Å s(-1). The functionality of the membranes is further illustrated by the growth of quantum heterostructures (such as quantum wells) and the characterization of their optical properties at the nanoscale. This proves the potential of nanoscale membranes for optoelectronic applications., GT, HP, FM and AFiM acknowledge SNF funding through the NCCR QSIT, its director's reserve and project nr 143908 and 134506 (DACH program), as well as CIME and CMI for access to the electron microscopes. Some of the research leading to these results has received funding from the European Union Seventh Framework Program under Grant Agreement 312483 – ESTEEM2 (Integrated Infrastructure Initiative – I3). JA and MdlM acknowledge the funding from the Spanish MINECO MAT2014-51480-ERC (e-ATOM), MAT2014-59961-C2-2-R and Severo Ochoa Excellence Program and Generalitat de Catalunya 2014SGR1638. MdlM thanks the CSIC Jae-Predoc program. The STEM and FIB sample preparation works have been conducted partially in the “Laboratorio de Microscopias Avanzadas” at “Instituto de Nanociencia de Aragon – Universidad de Zaragoza”. Authors acknowledge the LMA-INA for offering access to their instruments and expertise. Authors also acknowledge ICN2 for the use of their microscopy facilities. Lastly, we would like to acknowledge Fauzia Jabeen for her valuable help with our MBE system., Peer reviewed
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Solution-based synthesis and processing of Sn- and Bi-doped Cu₃SbSe₄ nanocrystals, nanomaterials and ring-shaped thermoelectric generators

  • Liu, Yu|||0000-0001-7313-6740
  • Ortega, Silvia|||0000-0002-3812-5146
  • Cadavid, Doris|||0000-0002-1376-6078
  • Ibáñez, Maria|||0000-0001-5013-2843
  • Xi, Lili
  • De Roo, Jonathan
  • López Peña, Antonio M.|||0000-0002-6979-5783
  • Martí-Sánchez, Sara|||0000-0003-4283-1489
  • Cabezas, Ignasi
  • De La Mata, Maria|||0000-0002-1581-4838
  • Luo, Zhishan|||0000-0002-0801-9238
  • Dun, Chaochao
  • Dobrozhan, Oleksandr|||0000-0001-9238-7596
  • Zhang, Wenqing
  • Martins, José
  • Kovalenko, Maksym V.|||0000-0002-6396-8938
  • Arbiol i Cobos, Jordi|||0000-0002-0695-1726
  • Noriega, German
  • Song, Ji-Ming
  • Cabot i Codina, Andreu|||0000-0002-7533-3251
Copper-based chalcogenides that comprise abundant, low-cost, and environmental friendly elements are excellent materials for a number of energy conversion applications, including photovoltaics, photocatalysis, and thermoelectrics (TE). In such applications, the use of solution-processed nanocrystals (NCs) to produce thin films or bulk nanomaterials has associated several potential advantages, such as high material yield and throughput, and composition control with unmatched spatial resolution and cost. Here we report on the production of Cu₃SbSe₄ (CASe) NCs with tuned amounts of Sn and Bi dopants. After proper ligand removal, as monitored by nuclear magnetic resonance and infrared spectroscopy, these NCs were used to produce dense CASe bulk nanomaterials for solid state TE energy conversion. By adjusting the amount of extrinsic dopants, dimensionless TE figures of merit (ZT) up to 1.26 at 673 K were reached. Such high ZT values are related to an optimized carrier concentration by Sn doping, a minimized lattice thermal conductivity due to efficient phonon scattering at point defects and grain boundaries, and to an increase of the Seebeck coefficient obtained by a modification of the electronic band structure with Bi doping. Nanomaterials were further employed to fabricate ring-shaped TE generators to be coupled to hot pipes, which provided 20 mV and 1 mW per TE element when exposed to a 160 °C temperature gradient. The simple design and good thermal contact associated with the ring geometry and the potential low cost of the material solution processing may allow the fabrication of TE generators with short payback times.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

A prototype reactor for highly selective solar-driven CO2 reduction to synthesis gas using nanosized earth-abundant catalysts and silicon photovoltaics

  • Urbain, Félix|||0000-0001-5423-6818
  • Tang, PengYi|||0000-0002-2306-095X
  • Carretero González, Nina Magali
  • Andreu, Teresa|||0000-0002-2804-4545
  • Gerling, Luis G.
  • Voz Sánchez, Cristóbal
  • Arbiol i Cobos, Jordi|||0000-0002-0695-1726
  • Morante, Joan Ramon|||0000-0002-4981-4633
The conversion of carbon dioxide (CO) into value-added chemicals and fuels, preferably using renewable energy and earth-abundant materials, is considered a key priority for future energy research. In this work, a bias-free reactor device for the solar-driven conversion of CO to synthesis gas (syngas) has been developed. The integrated fluidic device consists of a cathode made of copper foam coated with low-cost nanosized zinc flakes as catalyst to perform the CO reduction reaction (CORR) to syngas, an adapted silicon heterojunction solar cell structure as photoanode with nickel foam as catalyst to facilitate the oxygen evolution reaction (OER), and a bipolar membrane separating the respective catholyte and anolyte compartments. The membrane allows for the operation of the catholyte and anolyte at different pH values. Stable and tunable hydrogen-to-carbon monoxide (H:CO) ratios between 5 and 0.5 along with high CO Faradaic efficiencies of up to 85% and CO current densities of 39.4 mA cm have been demonstrated. Under photoelectrolysis conditions, the photovoltage of the photoanode was varied between 0.6 V and 2.4 V by connecting up to four heterojunction solar cells in series, and thus reducing the overall cell voltage solely by solar energy utilization. Bias-free operation of the integrated device has been achieved under ambient conditions with active areas for CORR and OER, respectively, of 10 cm. An operation current density of 5.0 mA cm was measured under 100 mW cm illumination of the complete device, which corresponds to a solar-to-syngas conversion efficiency of 4.3%.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Low-Temperature Growth of Axial Si/Ge Nanowire Heterostructures Enabled by Trisilane

  • Hui, Ho Yee
  • De La Mata, Maria|||0000-0002-1581-4838
  • Arbiol i Cobos, Jordi|||0000-0002-0695-1726
  • Filler, Michael A.
Axial Si/Ge heterostructure nanowires, despite their promise in applications ranging from electronics to thermal transport, remain notoriously difficult to synthesize. Here, we grow axial Si/Ge heterostructures at low temperatures using a Au catalyst with a combination of trisilane and digermane. This approach yields, as determined with detailed electron microscopy characterization, arrays of epitaxial Si/Ge nanowires with excellent morphologies and purely axial composition profiles. Our data indicate that heterostructure formation can occur via the vapor-liquid-solid or vapor-solid-solid mechanism. These findings highlight the importance of precursor chemistry in semiconductor nanowire synthesis and open the door to Si/Ge nanowires with programmable quantum domains.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Cobalt boride modified with N-doped carbon nanotubes as a high-performance bifunctional oxygen electrocatalyst

  • Elumeeva, Karina
  • Masa, Jistis
  • Medina, Danea
  • Ventosa, Edgar
  • Seisel, Sabine
  • Kayran, Yasin Ugur
  • Genç, Aziz|||0000-0002-2888-2549
  • Bobrowski, Tim
  • Weide, Philippe
  • Arbiol i Cobos, Jordi|||0000-0002-0695-1726
  • Muhler, Martin
  • Schuhmann, Wolfgang|||0000-0003-2916-5223
The development of reversible oxygen electrodes, able to drive both the oxygen evolution reaction (OER) and the oxygen reduction reaction (ORR), is still a great challenge. We describe a very efficient and stable bifunctional electrocatalytic system for reversible oxygen electrodes obtained by direct CVD growth of nitrogen-doped carbon nanotubes (NCNTs) on the surface of cobalt boride (CoB) nanoparticles. A detailed investigation of the crystalline structure and elemental distribution of CoB before and after NCNT growth reveals that the NCNTs grow on small CoB nanoparticles formed in the CVD process. The resultant CoB/NCNT system exhibited outstanding activity in catalyzing both the OER and the ORR in 0.1 M KOH with an overvoltage difference of only 0.73 V between the ORR at -1 mA cm⁻² and the OER at +10 mA cm⁻². The proposed CoB/NCNT catalyst showed stable performance during 50 h of OER stability assessment in 0.1 M KOH. Moreover, CoB/NCNT spray-coated on a gas diffusion layer as an air-breathing electrode proved its high durability during 170 galvanostatic charge-discharge (OER/ORR) test cycles (around 30 h) at ±10 mA cm⁻² in 6 M KOH, making it an excellent bifunctional catalyst for potential Zn-air battery application.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Surface-Guided Core-Shell ZnSe@ZnTe Nanowires as Radial p-n Heterojunctions with Photovoltaic Behavior

  • Oksenberg, Eitan|||0000-0001-9462-3986
  • Martí-Sánchez, Sara|||0000-0003-4283-1489
  • Popovitz-Biro, Ronit
  • Arbiol i Cobos, Jordi|||0000-0002-0695-1726
  • Joselevich, Ernesto|||0000-0002-9919-0734
The organization of nanowires on surfaces remains a major obstacle toward their large-scale integration into functional devices. Surface-material interactions have been used, with different materials and substrates, to guide horizontal nanowires during their growth into well-organized assemblies, but the only guided nanowire heterostructures reported so far are axial and not radial. Here, we demonstrate the guided growth of horizontal core-shell nanowires, specifically of ZnSe@ZnTe, with control over their crystal phase and crystallographic orientations. We exploit the directional control of the guided growth for the parallel production of multiple radial p-n heterojunctions and probe their optoelectronic properties. The devices exhibit a rectifying behavior with photovoltaic characteristics upon illumination. Guided nanowire heterostructures enable the bottom-up assembly of complex semiconductor structures with controlled electronic and optoelectronic properties.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Synergistic effects in 3D honeycomb-like hematite nanoflakes/branched polypyrrole nanoleaves heterostructures as high-performance negative electrodes for asymmetric supercapacitors

  • Tang, PengYi|||0000-0002-2306-095X
  • Han, Li-Juan
  • Genç, Aziz|||0000-0002-2888-2549
  • He, Yong-Min
  • Zhang, Xuan
  • Zhang, Lin|||0000-0003-1998-0611
  • Galán-Mascarós, José Ramón|||0000-0001-7983-9762
  • Morante, Joan Ramon|||0000-0002-4981-4633
  • Arbiol i Cobos, Jordi|||0000-0002-0695-1726
Rational assembly of unique branched heterostructures is one of the facile techniques to improve the electrochemical figure of merit of materials. By taking advantages of hydrogen bubbles dynamic template, hydrothermal method and electrochemical polymerization, branched polypyrrole (PPy) nanoleaves decorated honeycomb-like hematite nanoflakes (core-branch FeO@PPy) are fabricated. X-ray diffraction, X-ray photoelectron spectroscopy, scanning electron microscopy, transmission electron microscopy (TEM), high-resolution TEM, and scanning transmission electron microscopy in high angle annular dark field mode with electron energy loss spectroscopy were combined to elucidate the mechanisms underlying formation and morphogenesis evolution of core-branch FeO@PPy heterostructures. Benefiting from the stability of honeycomb-like hematite nanoflakes and the high conductivity of PPy nanoleaves, the resultant core-branch FeO@PPy exhibits an ultrahigh capacitance of 1167.8 F g at 1 A g in 0.5 M NaSO aqueous solution. Moreover, the assembled bi-metal oxides asymmetric supercapacitor (FeO@PPy//MnO) gives rise to a maximum energy density of 42.4 W h kg and a maximum power density of 19.14 kW kg with an excellent cycling performance of 97.1% retention after 3000 cycles at 3 A g. These performance features are superior than previous reported iron oxide/hydroxides based supercapacitors, offering an important guideline for future design of advanced next-generation supercapacitors.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Polybenzoxazine-derived N-doped carbon as matrix for powder-based electrocatalysts

  • Barwe, Stephan
  • Andronescu, Corina
  • Masa, Justus|||0000-0002-8555-5157
  • Ventosa, Edgar
  • Klink, Stefan
  • Genç, Aziz|||0000-0002-2888-2549
  • Arbiol i Cobos, Jordi|||0000-0002-0695-1726
  • Schuhmann, Wolfgang|||0000-0003-2916-5223
In addition to catalytic activity, intrinsic stability, tight immobilization on a suitable electrode surface, and sufficient electronic conductivity are fundamental prerequisites for the long-term operation of particle- and especially powder-based electrocatalysts. We present a novel approach to concurrently address these challenges by using the unique properties of polybenzoxazine (pBO) polymers, namely near-zero shrinkage and high residual-char yield even after pyrolysis at high temperatures. Pyrolysis of a nanocubic prussian blue analogue precursor (Km Mnx [Co(CN)₆]y⋅nH₂O) embedded in a bisphenol A and aniline-based pBO led to the formation of a N-doped carbon matrix modified with MnxCoyOz nanocubes. The obtained electrocatalyst exhibits high efficiency toward the oxygen evolution reaction (OER) and more importantly a stable performance for at least 65 h.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Mn₃O₄@CoMn₂O₄-CoₓOy nanoparticles, Partial cation exchange synthesis and electrocatalytic properties toward the oxygen reduction and evolution reactions

  • Luo, Zhishan|||0000-0002-0801-9238
  • Irtem, Erdem
  • Ibáñez, Maria|||0000-0001-5013-2843
  • Nafria, Raquel|||0000-0002-3254-1616
  • Martí-Sánchez, Sara|||0000-0003-4283-1489
  • Genç, Aziz|||0000-0002-2888-2549
  • De La Mata, Maria|||0000-0002-1581-4838
  • Liu, Yu|||0000-0001-7313-6740
  • Cadavid, Doris|||0000-0002-1376-6078
  • Llorca, Jordi|||0000-0002-7447-9582
  • Arbiol i Cobos, Jordi|||0000-0002-0695-1726
  • Andreu, Teresa|||0000-0002-2804-4545
  • Morante, Joan Ramon|||0000-0002-4981-4633
  • Cabot i Codina, Andreu|||0000-0002-7533-3251
Mn₃O₄@CoMn₂O₄ nanoparticles (NPs) were produced at low temperature and ambient atmosphere using a one-pot two-step synthesis protocol involving the cation exchange of Mn by Co in preformed Mn₃O₄ NPs. Selecting the proper cobalt precursor, the nucleation of CoₓOy crystallites at the Mn₃O₄@CoMn₂O₄ surface could be simultaneously promoted to form Mn₃O₄@CoMn₂O₄-CoₓOy NPs. Such heterostructured NPs were investigated for oxygen reduction and evolution reactions (ORR, OER) in alkaline solution. Mn₃O₄@CoMn₂O₄-CoₓOy NPs with [Co]/[Mn] = 1 showed low overpotentials of 0.31 V at -3 mA·cm-2 and a small Tafel slope of 52 mV·dec-1 for ORR, and overpotentials of 0.31 V at 10 mA·cm-2 and a Tafel slope of 81 mV·dec-1 for OER, thus outperforming commercial Pt-, IrO2-based and previously reported transition metal oxides. This cation-exchange-based synthesis protocol opens up a new approach to design novel heterostructured NPs as efficient nonprecious metal bifunctional oxygen catalysts.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

The Ethylhexanoate route to metal oxide nanocrystals, synthesis of CoO nanooctahedra from Co¹¹2-Ethylhexanoate

  • Epifani, Mauro|||0000-0002-9242-6484
  • Tang, PengYi|||0000-0002-2306-095X
  • Genç, Aziz|||0000-0002-2888-2549
  • Morante, Joan Ramon|||0000-0002-4981-4633
  • Arbiol i Cobos, Jordi|||0000-0002-0695-1726
  • Díaz, Raül
  • Wicker, Susanne
CoO nanocrystals were prepared by solvothermal processing of Co 2-ethylhexanoate in oleylamine at 250 °C. The obtained products, identified as CoO by X-ray diffraction, had an octahedral shape, as seen by transmission electron microscopy, reflecting the cubic symmetry of the CoO crystallographic phase. The materials were converted into the CO₃0₄ phase after heat treatment at 400 °C. The nanocrystal evolution was investigated by FTIR spectroscopy. It was concluded that weak oleylamine bonding to the nanocrystal surface during the synthesis step favored the exchange with 2-ethylhexanoato ligands, and that the interplay between the two ligands favored the kinetic control of the growth, resulting in the finally observed octahedral morphology. The CO₃0₄ phase obtained from the heat treatment at 400 °C was used to process chemoresistive sensors, which were able to detect ethanol under dry and humid conditions (0 and 50 % r.h. HO at 25 °C) at low temperatures (100 °C).
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Enhanced thermoelectric performance of solution-derived bismuth telluride based nanocomposites via liquid-phase sintering

  • Zhang, Chaohua
  • De La Mata, Maria|||0000-0002-1581-4838
  • Li, Zhong|||0000-0002-6009-629X
  • Belarre Triviño, Francisco Javier
  • Arbiol i Cobos, Jordi|||0000-0002-0695-1726
  • Khor, Khiam Aik|||0000-0003-1954-8423
  • Poletti, Dario
  • Zhu, Beibei|||0000-0001-5381-6634
  • Yan, Qingyu
  • Xiong, Qihua|||0000-0002-2555-4363
Bismuth telluride based thermoelectric materials show great promise in electricity generation from waste heat and solid-state refrigeration, but improving their conversion efficiency with economical approaches for widespread use remains a challenge. An economical facile bottom-up approach has been developed to obtain nanostructured powders, which are used to build bulk thermoelectric materials. Using excess tellurium as sacrificial additive to enable liquid-phase sintering in the spark plasma sintering process, the lattice and bipolar contributions to the thermal conductivity are both greatly reduced without compromising too much the power factor, which leads to the achievement of high figure of merit (ZT) in both n-type and p-type bismuth telluride based nanocomposites. The ZT values are 1.59±0.16 for p-type Bi0.5Sb1.5Te3 and 0.98±0.07 for n-type Bi2Te2.7Se0.3 at 370 K, which are significantly high for bottom-up approaches. These results demonstrate that solution-chemistry approaches as facile, scalable and low-energy-intensive ways to achieve nanopowders, combined with liquid-phase sintering process, can open up great possibilities in developing high-performance low-price thermoelectric bulk nanocomposites.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Enhanced activity and acid pH stability of Prussian blue-type oxygen evolution electrocatalysts processed by chemical etching

  • Han, Lijuan
  • Tang, PengYi|||0000-0002-2306-095X
  • Reyes-Carmona, Álvaro
  • Rodríguez-García, Bárbara
  • Torréns, Mabel
  • Morante, Joan Ramon|||0000-0002-4981-4633
  • Arbiol i Cobos, Jordi|||0000-0002-0695-1726
  • Galán-Mascarós, José Ramón|||0000-0001-7983-9762
The development of upscalable oxygen evolving electrocatalysts from earth-abundant metals able to operate in neutral or acidic environments and low overpotentials remains a fundamental challenge for the realization of artificial photosynthesis. In this study, we report a highly active phase of heterobimetallic cyanide-bridged electrocatalysts able to promote water oxidation under neutral, basic (pH < 13), and acidic conditions (pH > 1). Cobalt-iron Prussian blue-type thin films, formed by chemical etching of Co(OH)₁.₀ (CO₃)₀.₅·nH₂O nanocrystals, yield a dramatic enhancement of the catalytic performance toward oxygen production, when compared with previous reports for analogous materials. Electrochemical, spectroscopic, and structural studies confirm the excellent performance, stability, and corrosion resistance, even when compared with state-of-the-art metal oxide catalysts under moderate overpotentials and in a remarkably large pH range, including acid media where most cost-effective water oxidation catalysts are not useful. The origin of the superior electrocatalytic activity toward water oxidation appears to be in the optimized interfacial matching between catalyst and electrode surface obtained through this fabrication method.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Orientationally ordered silicon nanocrystal cuboctahedra in superlattices

  • Yu, Yixuan
  • Lu, Xiaotang
  • Guillaussier, Adrien
  • Voggu, Vikas Reddy
  • Pineros, William
  • De La Mata, Maria|||0000-0002-1581-4838
  • Arbiol i Cobos, Jordi|||0000-0002-0695-1726
  • Smilgies, Detlef-M.
  • Truskett, Thomas M.
  • Korgel, Brian A.
Uniform silicon nanocrystals were synthesized with cuboctahedral shape and passivated with 1-dodecene capping ligands. Transmission electron microscopy, electron diffraction, and grazing incidence wide-angle and small-angle X-ray scattering show that these soft cuboctahedra assemble into face-centered cubic superlattices with orientational order. The preferred nanocrystal orientation was found to depend on the orientation of the superlattices on the substrate, indicating that the interactions with the substrate and assembly kinetics can influence the orientation of faceted nanocrystals in superlattices.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Ultrasensitive binder-free glucose sensors based on the pyrolysis of in situ grown Cu MOF

  • Zhang, Xuan|||0000-0002-3667-4280
  • Luo, Jiangshui
  • Tang, PengYi|||0000-0002-2306-095X
  • Morante, Joan Ramon|||0000-0002-4981-4633
  • Arbiol i Cobos, Jordi|||0000-0002-0695-1726
  • Xu, Cai-Ling|||0000-0001-9360-3668
  • Li, Qingfeng
  • Fransaer, Jan|||0000-0002-0232-0687
A non-enzymatic glucose sensor based on carbon/Cu composite materials was developed by the in-situ growth and subsequent pyrolysis of metal-organic frameworks (MOFs) on Cu foam. After pyrolysis, SEM, HRTEM and STEM-EELS were employed to clarify the hierarchical Cu@porous carbon electrode. It is found that the Cu nanoparticles are uniformly embedded in the carbon matrix, carbon matrix in close contact with the pyrolized carbon sheets. The electrocatalytic activity of the Cu@porous carbon matrix electrode for glucose sensing was explored by cyclic voltammetry (CV) and chronoamperometry. The resulting Cu@porous carbon matrix electrode displays ultrahigh sensitivity (10.1 mA cm⁻² mM⁻¹), low detection limit (0.6 μM), short response time (less than 2 s) and good stability, indicating that the developed electrode is a promising glucose sensor.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Passivation layers for nanostructured photoanodes, Ultra-thin oxides on InGaN nanowires

  • Neuderth, Paula|||0000-0003-3468-2815
  • Hille, Pascal
  • Schörmann, Jörg
  • Frank, A.
  • Reitz, C.
  • Martí-Sánchez, Sara|||0000-0003-4283-1489
  • De La Mata, Maria|||0000-0002-1581-4838
  • Coll, Mariona|||0000-0001-5157-7764
  • Arbiol i Cobos, Jordi|||0000-0002-0695-1726
  • Marschall, R.
  • Eickhoff, Martin
An experimental strategy for systematically assessing the influence of surface passivation layers on the photocatalytic properties of nanowire photoanodes by combining photocurrent analysis, photoluminescence spectroscopy and high resolution transmission electron microscopy with a systematic variation of sample structure and the surrounding electrolyte is demonstrated. Following this approach we can separate the impact on recombination and transport processes of photogenerated carriers. We apply this strategy to analyze the influence of ultra-thin TiO, CeO and AlO coatings deposited by atomic layer deposition on the photoelectrochemical performance of InGaN/GaN nanowire (NW) photoelectrodes. The passivation of surface states results in an increase of the anodic photocurrent (PC) by a factor of 2.5 for the deposition of 5 nm TiO. In contrast, the PC is reduced for CeO- and AlO-coated NWs due to enhanced defect recombination in the passivation layer or increased band discontinuities. Furthermore, photoelectrochemical oxidation of the InGaN/GaN NW photoelectrode is attenuated by the TiO layer and completely suppressed for a layer thickness of 7 nm or more. Due to efficient charge transfer from the InGaN NW core a stable TiO-covered photoanode with visible light excitation is realized.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Growth and luminescence of polytypic InP on epitaxial graphene

  • Mukherjee, Samik|||0000-0002-5279-1110
  • Nateghi, Nima
  • Jacobberger, Robert M.
  • Bouthillier, Etienne
  • De La Mata, Maria|||0000-0002-1581-4838
  • Arbiol i Cobos, Jordi|||0000-0002-0695-1726
  • Coenen, Toon
  • Cardinal, Dhan
  • Levesque, Pierre
  • Desjardins, Patrick
  • Martel, Richard|||0000-0002-9021-4656
  • Arnold, Michael S.
  • Moutanabbir, Oussama|||0000-0002-0721-3696
Van der Waals epitaxy is an attractive alternative to direct heteroepitaxy where the forced coherency at the interface cannot sustain large differences in lattice parameters and thermal expansion coefficients between the substrate and the epilayer. Herein, the growth of monocrystalline InP on Ge and SiO/Si substrates using graphene as an interfacial layer is demonstrated. Micrometer-sized InP crystals are found to grow with interfaces of high crystalline quality and with different degrees of coalescence depending on the growth conditions. Some InP crystals exhibit a polytypic structure, consisting of alternating zinc-blende and wurtzite phases, forming a type-II homojunction with well (barrier) width of about 10 nm. The optical properties, investigated using room temperature nano-cathodoluminescence, indicate the signatures of the direct optical transitions at 1.34 eV across the gap of the zinc-blende phase and the indirect transitions at ≈1.31 eV originating from the alternating zinc-blende and wurtzite phases. Additionally, the InP nanorods, found growing mainly on the graphene/SiO/Si substrate, show optical transition across the gap of the wurtzite phase at ≈1.42 eV. This demonstration of InP growth on graphene and the correlative study between the structure and optical properties pave the way to develop hybrid structures for potential applications in integrated photonic and optoelectronic devices.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Insights into the Performance of CoxNi1-xTiO3 Solid Solutions as Photocatalysts for Sun-Driven Water Oxidation

  • Murcia López, Sebastián|||0000-0002-3703-041X
  • Moschogiannaki, Marilena
  • Binas, Vassilios
  • Andreu, Teresa|||0000-0002-2804-4545
  • Tang, PengYi|||0000-0002-2306-095X
  • Arbiol i Cobos, Jordi|||0000-0002-0695-1726
  • Jacas Biendicho, Jordi|||0000-0001-5981-6168
  • Kiriakidis, George
  • Morante, Joan Ramon|||0000-0002-4981-4633
CoNiTiO systems evaluated as photo- and electrocatalytic materials for oxygen evolution reaction (OER) from water have been studied. These materials have shown promising properties for this half-reaction both under (unbiased) visible-light photocatalytic approach in the presence of an electron scavenger and as electrocatalysts in dark conditions in basic media. In both situations, CoNiTiO exhibits the best performance and is proved to display high faradaic efficiency. A synergetic effect between Co and Ni is established, improving the physicochemical properties such as surface area and pore size distribution, besides affecting the donor density and the charge carrier separation. At higher Ni content, the materials exhibit behavior more similar to that of NiTiO, which is a less suitable material for OER than CoTiO.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Solvothermal Synthesis, Gas-Sensing Properties, and Solar Cell-Aided Investigation of TiO2-MoOx Nanocrystals

  • Epifani, Mauro|||0000-0002-9242-6484
  • Kaciulis, Saulius|||0000-0002-9868-7626
  • Mezzi, Alessio|||0000-0002-2887-520X
  • Altamura, Davide|||0000-0003-2597-4883
  • Giannini, Cinzia|||0000-0003-0983-2885
  • Tang, PengYi|||0000-0002-2306-095X
  • Morante, Joan Ramon|||0000-0002-4981-4633
  • Arbiol i Cobos, Jordi|||0000-0002-0695-1726
  • Siciliano, Pietro|||0000-0001-9748-0925
  • Comini, Elisabetta|||0000-0003-2559-5197
  • Concina, Isabella
Titania anatase nanocrystals were prepared by sol-gel/solvothermal synthesis in oleic acid at 250 °C, and modified by co-reaction with Mo chloroalkoxide, aimed at investigating the effects on gas-sensing properties induced by tailored nanocrystals surface modification with ultra-thin layers of MoO species. For the lowest Mo concentration, only anatase nanocrystals were obtained, surface modified by a disordered ultra-thin layer of mainly octahedral Mo oxide species. For larger Mo concentrations, early MoO phase segregation occurred. Upon heat treatment up to 500 °C, the sample with the lowest Mo concentration did not feature any Mo oxide phase segregation, and the surface Mo layer was converted to dense octahedral Mo oxide. At larger Mo concentrations all segregated MoO was converted to MoO. The two different materials typologies, depending on the Mo concentration, were used for processing gas-sensing devices and tested toward acetone and carbon monoxide, which gave a greatly enhanced response, for all Mo concentrations, to acetone (two orders of magnitude) and carbon monoxide with respect to pure TiO. For the lowest Mo concentration, dye-sensitized solar cells were also prepared to investigate the influence of anatase surface modification on the electrical transport properties, which showed that the charge transport mainly occurred in the ultra-thin MoO surface layer.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Growth of Au-Pd2Sn Nanorods via Galvanic Replacement and Their Catalytic Performance on Hydrogenation and Sonogashira Coupling Reactions

  • Nafria, Raquel|||0000-0002-3254-1616
  • Luo, Zhishan|||0000-0002-0801-9238
  • Ibáñez, Maria|||0000-0001-5013-2843
  • Martí-Sánchez, Sara|||0000-0003-4283-1489
  • Yu, Xiaoting|||0000-0003-0457-4047
  • De La Mata, Maria|||0000-0002-1581-4838
  • Llorca, Jordi|||0000-0002-7447-9582
  • Arbiol i Cobos, Jordi|||0000-0002-0695-1726
  • Kovalenko, Maksym V.|||0000-0002-6396-8938
  • Grabulosa, Arnald|||0000-0003-0198-4139
  • Muller, Guillermo|||0000-0001-6876-0389
  • Cabot i Codina, Andreu|||0000-0002-7533-3251
Colloidal PdSn and Au-PdSn nanorods (NRs) with tuned size were produced by the reduction of Pd and Sn salts in the presence of size- and shape-controlling agents and the posterior growth of Au tips through a galvanic replacement reaction. PdSn and Au-PdSn NRs exhibited high catalytic activity toward quasi-homogeneous hydrogenation of alkenes (styrene and 1-octene) and alkynes (phenylacetylene and 1-octyne) in dichloromethane. Au-PdSn NRs showed higher activity than PdSn for 1-octene, 1-octyne, and phenylacetylene. In Au-PdSn heterostructures, X-ray photoelectron spectroscopy evidenced an electron donation from the PdSn NR to the Au tips. Such heterostructures showed distinct catalytic behavior in the hydrogenation of compounds containing a triple bond such as tolan. This can be explained by the aurophilicity of triple bonds. To further study this effect, PdSn and Au-PdSn NRs were also tested in the Sonogashira coupling reaction between iodobenzene and phenylacetylene in N,N-dimethylformamide. At low concentration, this reaction provided the expected product, tolan. However, at high concentration, more reduced products such as stilbene and 1,2-diphenylethane were also obtained, even without the addition of H. A mechanism for this unexpected reduction is proposed.