Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 95
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

The fabrication of ultrathin films and their gas separation performance from polymers of intrinsic microporosity with two-dimensional (2D) and three-dimensional (3D) chain conformations

  • Benito, Javier
  • Vidal, Julio
  • Sánchez-Laínez, Javier
  • Zornoza, Beatriz
  • Téllez, Carlos
  • Martín, Santiago
  • Msayib, Kadhum J.
  • Comesaña-Gándara, Bibiana
  • McKeown, Neil B.
  • Coronas, Joaquín
  • Gascón, Ignacio
The expansion of the use of polymeric membranes in gas separation requires the development of membranes based on new polymers with improved properties and their assessment under real operating conditions. In particular, the fabrication of ultrathin films of high performance polymers that can be used as the selective layer in composite membranes will allow large reductions in the amount of the expensive polymer used and, hence, the cost of membrane fabrication. In this contribution, two polymers of intrinsic microporosity (PIMs) with very different chain configurations (two-dimensional, 2D, chains or conventional contorted three-dimensional, 3D, conformation) have been compared in their ability to form ultrathin films, showing the relevance of polymer design to obtain compact and defect-free films. Monolayers of the 2D polymer PIM-TMN-Trip can be efficiently deposited onto poly[1-(trimethylsilyl)-1-propyne] (PTMSP) to obtain composite membranes with a CO2/N2 selectivity similar to that of the corresponding thick membranes of the same PIM using only a small fraction of the selective polymer (less than 0.1%)., The research leading to these results has received funding from the European Community Seventh Framework Program (EU PF7) (FP7/2007-2013), under grant agreement number 608490, project M4CO2. Financial support from the Spanish MINECO (Ministry of Economy and Business) and FEDER (European Regional Development Fund) (MAT2016-77290-R), the Aragón Government (E31_17R and T43_17R) and the ESF is gratefully acknowledged. J. S.-L. thanks the Spanish Education Ministry Program FPU2014 for his PhD grant, Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Thin supported MOF based mixed matrix membranes of Pebax® 1657 for biogas upgrade

  • Sánchez-Laínez, Javier
  • Gracia-Guillén, Inés
  • Zornoza, Beatriz
  • Téllez, Carlos
  • Coronas, Joaquín
This work shows the preparation of thin mixed matrix membranes (MMMs) with a 2–3 μm thick Pebax® 1657 layer on two different supports: a porous asymmetric polyimide P84® and dense polytrimethylsilylpropyne (PTMSP). Nanoparticles of metal–organic frameworks (MOFs) ZIF-8, MIL-101(Cr), UiO-66 and ZIF-7/8 core–shells were selected as fillers for the Pebax® 1657 based MMMs, all of them being MOFs with high CO2 adsorption capacity but different pore size distribution. All the membranes were characterized by SEM, FTIR, Raman, TGA and XRD analyses, showing in all cases a perfect compatibility of the Pebax® layer with both supports and also a good dispersion of the fillers in the polymeric matrix. These membranes were applied for the separation of equimolar CO2/CH4 mixtures at 35 °C under feed pressures between 3 and 5 bar, where an improvement in the gas separation performance with increasing pressure was noticed, thanks to the favored solubility of CO2. The synergistic compatibility between Pebax® 1657 and P84® gave rise to a 470% enhancement in CO2/CH4 selectivity, reaching a maximum value of 114 while the CO2 permeance increased by 40% up to 7.5 GPU. The addition of fillers in the Pebax® polymeric phase produced an improvement in the gas separation performance of the membranes, especially in terms of permeance, where the MMMs containing a 10 wt% loading of UiO-66 reached the optimum value of 11.5 GPU of CO2 (together with a CO2/CH4 selectivity of 55.6)., Financial support from the Spanish MINECO and FEDER (MAT2016-77290-R), the Aragon Government (T43-17R) and the ESF is gratefully acknowledged. J. S.-L. thanks the Spanish Education Ministry Program FPU2014 for his PhD grant., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Ultrathin composite polymeric membranes for CO2 /N2 separation with minimum thickness and high CO2 permeance

  • Benito, Javier
  • Sánchez-Laínez, Javier
  • Zornoza, Beatriz
  • Martín, Santiago
  • Carta, Mariolino
  • Malpass-Evans, Richard
  • Téllez, Carlos
  • McKeown, Neil B.
  • Coronas, Joaquín
  • Gascón, Ignacio
The use of ultrathin films as selective layers in composite membranes offers significant advantages in gas separation for increasing productivity while reducing the membrane size and energy costs. In this contribution, composite membranes have been obtained by the successive deposition of approximately 1 nm thick monolayers of a polymer of intrinsic microporosity (PIM) on top of dense membranes of the ultra-permeable poly[1-(trimethylsilyl)-1-propyne] (PTMSP). The ultrathin PIM films (30 nm in thickness) demonstrate CO2 permeance up to seven times higher than dense PIM membranes using only 0.04 % of the mass of PIM without a significant decrease in CO2 /N2 selectivity., The research leading to these results has received funding from the EU FP7 Programme (FP7/2007–2013), under grant agreement number 608490, project M4CO2, Spanish MINECO and FEDER (MAT2016-77290-R) and the Aragon Government (T05 and E54). J. S.-L. thanks the Spanish Education Ministry Program FPU2014 for a Ph.D. grant., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Reactive gas atmospheres as a tool for the synthesis of MOFs: the creation of a metal hybrid fumarate with a controlled Fe/Al composition profile

  • Monteagudo-Olivan, Rebeca
  • Arruebo, Manuel
  • López-Ram-de-Víu, Pilar
  • Sebastián, Víctor
  • Coronas, Joaquín
The use of reactive gas atmospheres is proposed here as a new tool to control the synthesis of MOFs. With the addition of Al to an Fe-fumarate synthesis medium (which produces the typical structure of MOF MIL-88A(Fe)), a hybrid Fe/Al-fumarate that exhibits the structure of MOF MIL-53(Al)-FA was obtained even though both metals could be identified in the resulting material by STEM-HAADF. The use of CO and O2 atmospheres (6 bar) in the synthesis of both MIL-88A(Fe) and MIL-53(Fe/Al)-FA might accelerate their synthesis and give rise to a highly crystalline solid and to core–shell nanoparticles (190 ± 42 nm) with an Fe-rich core surrounded by an Al-rich shell, i.e., with a controlled Fe/Al atomic distribution. After pyrolysis the MIL-53(Fe/Al)-FA particles exhibited superparamagnetism while keeping some texture (244 m2 g−1vs. 862 m2 g−1 of the as-made material)., The authors acknowledge financial support from the Spanish MINECO and FEDER (MAT2016-77290-R), Aragón Government (DGA, T05), Universidad de Zaragoza (2007/0016) and ERC Consolidator Grant program (ERC-2013-CoG-614715, NANOHEDONISM) and People Program (CIG-Marie Curie Actions, REA grant agreement no. 321642). CIBER-BBN is an initiative funded by the VI National R&D&i Plan 2008–2011 financed by the Instituto de Salud Carlos III with the assistance of the European Regional Development Fund., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

110th anniversary: Polyamide/metal–organic framework bilayered thin film composite membranes for the removal of pharmaceutical compounds from water

  • Paseta, Lorena
  • Antorán, Daniel
  • Coronas, Joaquín
  • Téllez, Carlos
Nanofiltration can be a useful tool to remove pharmaceuticals in water sources. The performance of the most used thin film composite (TFC) membranes, typically with a thin polyamide (PA) layer, can be improved using thin film nanocomposite (TFN) membranes obtained by the introduction of a filler within the PA layer. In this work, to control the positioning of the filler two kinds of PA/metal–organic framework (MOF) bilayered TFC (BTFC) membranes, PA/ZIF-93 and PA/HKUST-1, were synthesized onto polyimide supports. First, the interfacial synthesis was used for the preparation of a MOF layer, and second, a PA layer was synthesized by interfacial polymerization. These BTFC membranes were applied in the nanofiltration of diclofenac and naproxen aqueous solutions obtaining a maximum water permeance of 33.1 and 24.9 L·m–2·h–1·bar–1, respectively, with a rejection of ≥98% when HKUST-1 was used. These permeance improvements (using diclofenac, 4.9 and 3.4 times the value of the TFC and TFN membranes, respectively) are related to the PA layer thickness, MOF porosity, membrane hydrophilicity, and membrane roughness., Financial support from the Spanish MINECO and FEDER (MAT2016-77290-R), the Aragon Government (T43-17R) and the ESF is gratefully acknowledged. L.P. thanks the Spanish Ministry of Economy, Industry and Competitiveness Program FPI2014 for her Ph.D. grant., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Graphene oxide – Filled polyimide membranes in pervaporative separation of azeotropic methanol–MTBE mixtures

  • Castro-Muñoz, Roberto
  • Galiano, Francesco
  • Iglesia, Óscar de la
  • Fíla, Vlastimil
  • Téllez, Carlos
  • Coronas, Joaquín
  • Figoli, Alberto
Graphene oxide (GO)-polyimide mixed matrix membranes (MMMs) were produced using chloroform by solvent evaporation. These membranes have been used, for the first time, in pervaporation (PV) for the separation of azeotropic methanol (MeOH)- methyl tert-butyl ether (MTBE) mixtures (14.3 and 85.7%, respectively). The effect of GO loading in the PV process was investigated. The PV experiments were carried out at different feed operating temperatures (25–45 °C). Furthermore, an analysis of the PV process through the Arrhenius relationship has been given. The feed temperature (in the range of 25–45 °C) affected the permeation of both components producing an increase in total permeate flux; however, separation factor was compromised. Indeed, the best permeate fluxes (ca. 0.091 kg m−2 h−1) of the MMMs (4 wt% GO) were found at 45 °C, while the best separation factor (α = 28) was found at 1 wt% GO at 25 °C. In addition, the membranes were characterized by TGA, SEM, DSC, solvent uptake and mechanical test (Young’s modulus). Finally, the performance of the GO-polyimide membranes was compared with other polymeric and MMMs membranes at the azeotropic conditions., R. Castro-Muñoz acknowledges the European Commission - Education, Audiovisual and Culture Executive Agency (EACEA) for his PhD scholarship under the program: Erasmus Mundus Doctorate in Membrane Engineering – EUDIME (FPA No 2011-0014, Edition V, http:/eudime.unical.it). This work was partially supported by the Operational Program Prague – Competitiveness (CZ.2.16/3.1.00/24501) and the “National Program of Sustainability“ (NPU I LO1613) MSMT-43760/2015. Financial support from the Spanish MINECO and FEDER (MAT2016-77290-R), the Aragón Government (T43-17R) and the ESF is also gratefully acknowledged., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Greener processes in the preparation of thin film nanocomposite membranes with diverse metal-organic frameworks for organic solvent nanofiltration

  • Paseta, Lorena
  • Navarro, Marta
  • Coronas, Joaquín
  • Téllez, Carlos
The toxic solvent dimethylformamide has been replaced by the greener dimethylsulfoxide in the casting and activation processes for the preparation of thin film composite (TFC) membranes. This methodology has been validated with the use of MOFs ZIF-8, ZIF-93 and UiO-66 as fillers for thin-film nanocomposite (TFN) membranes. These membranes were successfully applied in the organic solvent nanofiltration of sunset yellow (SY) in methanol obtaining the highest permeance when UiO-66 and ZIF-93 were used with a value of 11 L m−2 h-1 bar-1. The permeance improvements are related to the MOF porosity, polyamide-MOF layer thickness and the hydrophilic/hydrophobic character of the membrane., Financial support from the Research Projects MAT2016-77290-R (MINECO/AEI/FEDER, UE) and T43-17R (the Aragón Government and the ESF) is gratefully acknowledged. Lorena Paseta would like to express her gratitude to the Spanish MINECO for the predoctoral grant (BES-2014-068287) awarded., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

High-pressure CO2/CH4 separation of Zr-MOFs based mixed matrix membranes

  • Zamidi Ahmad, Mohd
  • Peters, Thijs A.
  • Konnertz, Nora M.
  • Visser, Tymen
  • Téllez, Carlos
  • Coronas, Joaquín
  • Fíla, Vlastimil
  • Vos, Wiebe M. de
  • Benes, Nieck E.
The gas separation properties of 6FDA-DAM mixed matrix membranes (MMMs) with three types of zirconium-based metal organic framework nanoparticles (MOF NPs, ca. 40 nm) have been investigated up to 20 bar. Both NPs preparation and MMMs development were presented in an earlier publication that reported outstanding CO2/CH4 separation performances (50:50 vol% CO2/CH4 feed at 2 bar pressure difference, 35 °C) and this subsequent study is to demonstrate its usefulness to the natural gas separation application. In the current work, CO2/CH4 separation has been investigated at high pressure (2–20 bar feed pressure) with different CO2 content in the feed (10–50 vol%) in the temperature range 35–55 °C. Moreover, the plasticization, competitive sorption effects, and separation of the acid gas hydrogen sulfide (H2S) have been investigated in a ternary feed mixture of CO2:H2S:CH4 (vol% ratio of 30:5:65) at 20 bar and 35 °C. The incorporation of the Zr-MOFs in 6FDA-DAM enhances both CO2 permeability and CO2/CH4 selectivity of this polymer. These MMMs exhibit high stability under separation conditions relevant to an actual natural gas sweetening process. The presence of H2S does not induce plasticization but increases the total acid gas permeability, acid gas/CH4 selectivity and only causes reversible competitive sorption. The overall study suggests a large potential for 6FDA-DAM Zr-MOF MMMs to be applied in natural gas sweetening, with good performance and stability under the relevant process conditions., The research leading to these results has received funding from ECCSEL (Grant Agreement no. 675206, European Union’s Horizon 2020 research and innovation programme). The authors also acknowledge the financial support of EACEA/European Commission, within the “Erasmus Mundus Doctorate in Membrane Engineering – EUDIME” (ERASMUS MUNDUS Programme 2009-2013, FPA n. 2011-0014, SGA n. 2012-1719), the Spanish Ministry of Economy and Competitiveness (MINECO), FEDER (MAT2016-77290-R), the European Social Fund and the Aragón Government (DGA, T05). Also the Operational Programme Prague–Competitiveness (CZ.2.16/3.1.00/24501) and National Program of Sustainability (NPU I LO1613) MSMT-43760/2015., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Mathematical modeling of temperature and pressure effects on permeability, diffusivity and solubility in polymeric and mixed matrix membranes

  • Maghami, Saeid
  • Mehrabani-Zeinabad, Arjomand
  • Sadeghi, Morteza
  • Sánchez-Laínez, Javier
  • Zornoza, Beatriz
  • Téllez, Carlos
  • Coronas, Joaquín
Due to the temperature and pressure dependency of gas transport through polymeric and mixed matrix membranes, probing of their separation performance at different operational conditions seems crucial to determine an optimal operational condition. To minimize the number of costly and time consuming experiments, a modified form of van’t Hoff-Arrhenius model was developed to consider the simultaneous effects of temperature and pressure on the separation performance of polymeric and mixed matrix membranes. Moreover, the proposed model is capable to consider pressure dependency of energetic parameters of Arrhenius model including activation energies of permeability and diffusivity, heat of sorption and the corresponding pre-exponential factors. The validity of the proposed model was investigated by using permeation coefficients of CO2 and N2 in a binary mixture through 6FDA-DAM at different temperatures in the range of 35–55 °C and in the feed pressure range from 2 to 5 atm. Besides, from data taken from the literature, the proposed model was validated by the prediction of temperature and pressure dependency of transport properties of glassy and rubbery polymers as well as mixed matrix membranes (MMMs) for different gas molecules including He, H2, CO2, O2, N2, CH4 and C4H10. Predictions corresponding to 300 data points revealed that the maximum average absolute relative error was 5.1%., Financial support from the Spanish MINECO and FEDER (MAT2016-77290-R), the Aragón Government (T43-17R) and the ESF is gratefully acknowledged. L. P. thanks the Spanish Ministry of Economy, Industry and Competitiveness Program FPI2014 for her PhD grant. J. S.-L. thanks the Spanish Education Ministry Program FPU2014 for his PhD grant., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Nanosheets of MIL-53(Al) applied in membranes with improved CO2/N2 and CO2/CH4 selectivities

  • Perea-Cachero, Adelaida
  • Sánchez-Laínez, Javier
  • Zornoza, Beatriz
  • Romero-Pascual, Enrique
  • Téllez, Carlos
  • Coronas, Joaquín
MIL-68(Al) and MIL-53(Al) are carboxylate-based metal–organic frameworks (MOFs) with the same chemical composition but different structures (polymorphs). In this study, MIL-53(Al) nanosheets of ca. 150 nm in size with an average thickness of 3.5 ± 0.9 nm were obtained after immersion of a sample composed of MIL-68(Al) and MIL-53(Al) in water under different conditions (ultrasound, stirring, reflux, 60 °C and room temperature). The disaggregated MIL-53(Al) nanosheets produced under more severe conditions were suspended in a PDMS solution and then deposited on asymmetric polyimide P84® supports under vacuum filtration to form supported mixed matrix membranes (MMMs). When applied to the separation of CO2/CH4 and CO2/N2 mixtures, the MMM with MIL-53(Al) nanosheets improved the CO2/CH4 (28.4–28.7 vs. 22.4) and CO2/N2 (19.9–23.2 vs. 17.5) selectivities of the conventional MIL-53(Al) MMM with higher CO2 permeances (20.8–29.6 GPU vs. 9.5 GPU for CO2/CH4 and 17.7–26.8 GPU vs. 11.2 GPU for CO2/N2)., Financial support from the Spanish Ministry of Economy and Competitiveness (MINECO) and FEDER (MAT2016-77290-R), the European Social Fund (ESF) and the Aragón Government (DGA, T43_17R) is gratefully acknowledged. A. P.-C. and J. S.-L. also thank the DGA and Spanish Education Ministry Program FPU2014, respectively, for Ph.D. grants., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Poly(ether-block-amide) copolymer membrane for CO2/N2 separation: the influence of the casting solution concentration on its morphology, thermal properties and gas separation performance

  • Martínez-Izquierdo, Lidia
  • Malankowska, Magdalena
  • Sánchez-Laínez, Javier
  • Téllez, Carlos
  • Coronas, Joaquín
The present work is focused on the study of the effect that the casting solution concentration has on the morphology and gas separation performance of poly(ether-block-amide) copolymer membranes (Pebax® MH 1657). With this aim, three different concentrations of Pebax® MH 1657 in the casting solution (1, 3 and 5 wt%) were used to prepare dense membranes with a thickness of 40 µm. The morphology and thermal stability of all membranes were characterized by scanning electron microscopy, X-ray diffraction, differential scanning calorimetry, rotational viscometry and thermogravimetric analyses. An increase in crystallinity was notable when the amount of solvent in the Pebax® MH 1657 solution was higher, mainly related to the polymer chains arrangement and the solvent evaporation time. Such characteristic seemed to play a key role in the thermal degradation of the membranes, confirming that the most crystalline materials tend to be thermally more stable than those with lower crystallinity. To study the influence of their morphology and operating temperature on the CO2 separation, gas separation tests were conducted with the gas mixture CO2/N2. Results indicated that a compromise must be found between the amount of solvent used to prepare the membranes and the crystallinity, in order to reach the best gas separation performance. In this study, the best performance was achieved with the membrane prepared from a 3 wt% casting solution, reaching at 35°C and under a feed pressure of 3 bar, a CO2 permeability of 110 Barrer and a CO2/N2 selectivity of 36., This project has received funding from the European Union’s Horizon 2020 research and innovation programme under grant agreement no. 760944 (MEMBER project). Also, financial support from the Spanish Ministry of Science, Innovation and Universities and FEDER (MAT2016-77290-R), the Aragón Government (T43-17R) and the ESF is gratefully acknowledged., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Polymer engineering by blending PIM-1 and 6FDA-DAM for ZIF-8 containing mixed matrix membranes applied to CO2 separations

  • Sánchez-Laínez, Javier
  • Pardillos-Ruiz, Alberto
  • Carta, Mariolino
  • Malpass-Evans, Richard
  • McKeown, Neil B.
  • Téllez, Carlos
  • Coronas, Joaquín
The preparation of mixed matrix membranes (MMMs) for post-combustion CO2 capture and biogas upgrading from PIM-1 (10–90 wt%)/6FDA-DAM heterogeneous blends with ZIF-8 as filler (3–20 wt% with regard to the polymer blend) is described. The heterogeneity of the blend, considered here as an advantage for the dispersion of the filler within the MMMs, has been confirmed by the existence of a single glass transition temperature, consistent with that of 6FDA-DAM. The segregation between the two polymeric phases and the filler dispersion has been studied by Raman spectroscopy, SEM microscopy and EDX analysis. Increasing the amount of PIM-1 in the blend makes the d-spacing of the polymer chains higher and increases gas permeability. When embedding filler nanoparticles of ZIF-8, a better compatibility with 6FDA-DAM than with PIM-1 is observed. The filler locates near the interphase between polymers helping its dispersion. The use of small loadings of ZIF-8 enhances the gas separation performance of the MMMs in terms of permeability and selectivity for 50/50 CO2/CH4 and 10/90 CO2/N2 mixtures. The best performing membranes are the blends PIM-1/6FDA-DAM 10/90 (w/w) with 10 wt% of ZIF-8, showing a CO2 permeability of 2891 Barrer, a CO2/CH4 selectivity of 26.6 and 2802 Barrer of CO2 with a CO2/N2 selectivity of 18.1. Importantly, the CO2, N2 and CH4 permeabilities of the pure polymeric blends can be predicted using both the logarithmic and the Maxwell models. A new coupled Maxwell model has also been developed able to calculate the flow through the blends containing ZIF-8 and to predict the gas separation properties of the filler itself., Financial support from the Spanish MINECO and FEDER (MAT2016-77290-R), the Aragón Government (T43-17R) and the ESF is gratefully acknowledged. J. S.-L. thanks the Spanish Education Ministry Program FPU2014 for his PhD grant., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Towards the dehydration of ethanol using pervaporation cross-linked poly(vinyl alcohol)/graphene oxide membranes

  • Castro-Muñoz, Roberto
  • Buera-González, Juan
  • Iglesia, Óscar de la
  • Galiano, Francesco
  • Fíla, Vlastimil
  • Malankowska, Magdalena
  • Rubio, César
  • Figoli, Alberto
  • Téllez, Carlos
  • Coronas, Joaquín
Highly hydrophilic inorganic material graphene oxide (GO) was successfully prepared and incorporated into a cross-linked poly(vinyl alcohol) (PVA) matrix. The obtained mixed matrix membranes (MMMs) have been used for the dehydration of ethanol (10:90% water-ethanol) by pervaporation (PV), monitoring their performance in terms of total permeate flux, partial components fluxes, as well as their separation factor. The effect of filler was analyzed by doubling the GO content (at 0.5, 1.0, and 2.0 wt%) in the MMMs. A complete analysis of the operating temperature (between 40 and 70 °C) was carried out by means of Arrhenius relationship. Moreover, the membranes were characterized by field emission scanning electron microscopy (FESEM), transmission electron microscopy (TEM), differential scanning calorimetry (DSC), thermo-gravimetric analysis (TGA), X-ray diffraction (XRD), Fourier transformed infrared spectroscopy (FTIR), measurements of degree of swelling (uptake), water contact angle (CA) and mechanical properties. At 40 °C, the best performance was provided by the MMMs containing 1 wt% GO, showing a separation factor of 263 and a permeate flux of about 0.137 kg m−2 h−1 (in which 0.133 kg m−2 h−1 corresponds to water). This represents a 75% enhancement of the original permeation rate of pristine cross-linked PVA membranes. Taking into account the promising results, it is likely that these MMMs will provide featured benefits in green processes, e.g. ethanol purification by means of less-energy consumption., R. Castro-Muñoz acknowledges the European Commission - Education, Audiovisual and Culture Executive Agency (EACEA) for his PhD scholarship under the program: Erasmus Mundus Doctorate in Membrane Engineering – EUDIME (FPA No 2011-0014, Edition V, http://eudime.unical.it). This work was partially supported by the Operational Program Prague – Competitiveness (CZ.2.16/3.1.00/24501) and the “National Program of Sustainability” (NPU I LO1613) MSMT-43760/2015. Financial support from the Spanish MINECO and FEDER (MAT2016-77290-R), the Aragón Government (T43-17R) and the ESF is also gratefully acknowledged., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Tin-carboxylate MOFs for sugar transformation into methyl lactate

  • Murillo, Beatriz
  • Zornoza, Beatriz
  • Iglesia, Óscar de la
  • Wang, Sujing
  • Serre, Christian
  • Téllez, Carlos
  • Coronas, Joaquín
With the purpose of improving the production of methyl lactate (ML) from sugars (glucose and sucrose), a new metal‐organic framework (MOF) denoted as UZAR‐S10, containing Sn ions and ligand 2‐aminobenzene‐1,4‐dicarboxylate was synthesized. The SEM and PXRD characterization revealed that UZAR‐S10 was highly crystalline. The empirical formula of UZAR‐S10 is [(NH2‐BDC)Sn]·(NH2‐BDC)0.5, i.e., per Sn atom, with one structural ligand molecule and half ligand molecule trapped in the MOF structure. The removal of the trapped ligand by either solvent extraction or thermal treatment damaged the structure of UZAR‐S10, not enabling its activation. The performance of UZAR‐S10 in the production of ML was compared to those achieved with different types of carboxylate MOFs, especially with that of Sn partially substituted Ti tetracarboxylate MOF denoted MIP‐177‐LT (MIP‐177‐LT(Ti/Sn)). The highest ML yields achieved from sucrose were 29.5 % and 42.0 % for UZAR‐S10 and MIP‐177‐LT(Ti/Sn), respectively. For comparison, other carboxylate type MOFs (MIL‐53(Al), NH2‐MIL‐53(Al), UiO‐66, MIL‐101(Cr) and HKUST‐1) were tested at the same conditions with worse performance than the two Tin‐containing MOFs., Financial support from the Spanish Ministry of Economy and Competitiveness (MAT2016–77290‐R) and the European Social Fund (ESF) through the Aragón Government (T43–17R) is gratefully acknowledged., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Synthesis and characterization of covalent triazine framework CTF-1@polysulfone mixed matrix membranes and their gas separation studies

  • Dey, Subarna
  • Bügel, Stefanie
  • Sorribas, Sara
  • Nuhnen, Alexander
  • Bhunia, Asamanjoy
  • Coronas, Joaquín
  • Janiak, Christoph
Covalent triazine framework CTF-1 and polysulfone (PSF) are used to form mixed-matrix membranes (MMMs) with 8, 16, and 24 wt% of the porous filler material CTF-1. Studies on permeability and selectivity are carried out concerning the gases O2, N2, CO2, and CH4. CO2 permeability of the synthesized MMMs increases by 5.4 Barrer in comparison to the pure PSF membrane. The selectivity remains unchanged for O2/N2 and CO2/CH4 but was found to be increased for CO2/N2. Further, comparisons to theoretical models for permeability prediction yield a permeability for CTF-1 which is about six times higher than the permeability of PSF. The inverse of the sum of the free fractional volumes (FFV) of the polymer and the filler correlate linearly to the logarithm of the permeabilities of the gases which conversely indicates that the porosity of the filler contributes to the gas transport through the membrane., Financial support from the Spanish MINECO and FEDER (MAT2016-77290-R), the Aragón Government (T43-17R), and the ESF was gratefully acknowledged by JC. The work of CJ was supported by the Federal German Ministry of Education and Research (BMBF) under grant Optimat 03SF0492C., Open access publication fees were covered by Heinrich-Heine-University., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Contribución de congreso (ConferenceOutput)

MOF synthesis on carbon nanotubes buckypaper for gas separation

  • Berned-Samatán, Víctor
  • Galán, Alejandro
  • Rubio, César
  • Perea-Cachero, Adelaida
  • Muñoz, Edgar
  • Benito, Ana M.
  • Maser, Wolfgang K.
  • Téllez, Carlos
  • Coronas, Joaquín
Resumen del trabajo presentado a la XXXVII Reunión Bienal de la Real Sociedad Española de Química, celebrada en Donostia-San Sebastián del 26 al 30 de mayo de 2019., Financial support from the Spanish Ministry of Economy and Competitiveness (MINECO) and European Regional Development Fund (MAT2016-77290-R), ESF and the Aragón Government (T43-17R) is gratefully acknowledged., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Contribución de congreso (ConferenceOutput)

TEM characterization of nanocomposite polymer membranes with MOF fillers for nanofiltration

  • Navarro, Marta
  • Paseta, Lorena
  • Echaide‐Górriz, Carlos
  • Benito, Javier
  • Gascón, Ignacio
  • Coronas, Joaquín
  • Téllez, Carlos
Póster presentado al Microscopy at the Frontiers of Science Congress Series (MFS), celebrado en el Parque de las Ciencias de Granada (España) del 11 al 13 de septiembre de 2019., Thin film composite (TFC) membranes consist of a polyamide (PA) thin film (35-100 nm thick) as a selective layer, grown via interfacial polymerization (IP) of monomeric acid chlorides and amines on top of an asymmetric polyimide support, cast over a polypropylene non-woven backing material by phase inversion. This type of membrane is very competitive for organic solvent nanofiltration, where chemical stable polymers are mandatory. In order to increase membrane flux without decreasing rejection, nanoparticles are incorporating during the IP process, giving rise to Thin film nanocomposite (TFN) membranes (Fig. 1a). Their performance is determined by the structural and physicochemical properties of the fillers and PA thin film. Metal organic frameworks (MOFs), built from organic linkers and metal-containing clusters, have been extensively included as fillers in TFN membranes, showing exceptional affinity with polymer chains and improved solvent permeation. The combination of nanoscale visualization via conventional Transmission electron microscopy (TEM) and Scanning transmission electron microscopy (STEM), and spectroscopic analysis via energy dispersive X-ray spectroscopy (EDX) and Electron energy loss spectroscopy (EELS), are some of the most potent techniques for shedding further light into the connection between the nanostructure of the MOF-PA film and their transport and rejection properties. Sample preparation is a key step to examine the presence, distribution and morphology of MOF nanoparticles within the PA film, but also to confirm their crystallinity after the IP process by electron microscopy, given the multilayer and heterogeneous character of these membranes and but also because of the beamsensitive nature of MOFs. Here, we report different sample preparation protocols for applying TEM, STEM-EDS/EELS and electron diffraction depending on the nature of the TFN sample and on the characterization aim: 1. When the aim was to confirm the presence, distribution and morphology of two types of MOFs of different chemical composition in the PA layer, a fragment of the MOF-PA film was detached from the polyimide support in the last stage of the IP process. The fragment was removed from the distilled water bath and placed onto a carbon film grid. TEM and STEM-EDS techniques were applied. 2. When the objective was to check the distribution of the MOF nanoparticles within the TFN membrane and their crystallinity, a MOF-TFN membrane was synthesized over a non-crosslinked polyimide support without backing material. Then, the membrane was immersed in N,N-dimethylformamide at room temperature for 5 min to dissolve the polyimide support. The separated PA top layer was placed onto a carbon film grid. TEM and electron diffraction were applied. 3. When the goal was to verify the presence of a defect free MOF monolayer film in between the two polymer layers (Fig. 1b), transferred by the Langmuir-Schaefer (LS) technique, a lamella (∼80 nm thick) was obtained from the upper 2 μm of the TFN membrane using cryo-focused ion beam (FIB) equipment (Dual Beam 3 Nova 200) and Ga atoms for the etching. STEM-EDS/EELS techniques were applied (Fig. 1c)., Financial support from the Research Project MAT2016-77290-R (MINECO/AEI/FEDER, UE) is gratefully acknowledged., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Conversion of sugars to methyl lactate with exfoliated layered stannosilicate UZAR-S4

  • Murillo, Beatriz
  • Iglesia, Óscar de la
  • Rubio, César
  • Coronas, Joaquín
  • Téllez, Carlos
Biomass has been shown as an alternative to fossil fuels for obtaining chemicals. In this work, the transformation of sugars into methyl lactate (ML) at 160 °C was carried out using the layered stannosilicate UZAR-S3 (University of Zaragoza-solid number 3) and the delaminated material UZAR-S4 (University of Zaragoza-solid number 4) obtained from its exfoliation. The exfoliation of UZAR-S3 to UZAR-S4 increased the accessibility of the compounds to the catalytic sites and the medium-strength acidity. Thus, the yield to ML for sucrose transformation increased from 8% for UZAR-S3 to 49.9 % for UZAR-S4. In the reusability tests, the UZAR-S4 catalyst was characterized before and after reaction by several techniques such as X-ray diffraction, thermogravimetry analysis, scanning electronic microscopy, energy dispersive X-ray spectroscopy and nitrogen adsorption. A deactivation of the catalyst was observed, which was related to carbonaceous deposits that decreased the specific surface area and the pore volume of the catalyst., Financial support from the Research Projects MAT2016-77290-R (AEI/FEDER, UE) and T43-17R (the Aragón Government and the ESF) is gratefully acknowledged., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Functionalized graphene-based polyamide thin film nanocomposite membranes for organic solvent nanofiltration

  • Paseta, Lorena
  • Luque-Alled, José Miguel
  • Malankowska, Magdalena
  • Navarro, Marta
  • Gorgojo, Patricia
  • Coronas, Joaquín
  • Téllez, Carlos
This work deals with the use of octadecylamine (ODA)-functionalized reduced graphene oxide (rGO) for thin film nanocomposite (TFN) membranes. The functionalization of rGO with ODA leads to graphene-based nanofillers, more hydrophobic than GO, and thus to the easier dispersion in the organic phase of the interfacial polymerization (IP) reaction carried out to produce polyamide (PA) TFN membranes. The performance of the new TFN membranes is evaluated by organic solvent nanofiltration (OSN) of alcoholic solutions containing dyes Acridine Orange (AO, MW 265 g·mol−1), Sunset Yellow (SY, MW 452 g·mol−1) and Rose Bengal (RB, MW 974 g·mol−1). The functionalized nature of the nanoparticles introduced into the hydrophilic PA layer allows an increase of the ethanol permeance from 2.8, 3.4 and 3.7 L·m−2·h−1·bar−1 for AO, SY and RB, respectively, corresponding to the bare thin film composite membrane (without rGO-ODA particles), to 4.3, 4.6 and 6.0 L·m−2·h−1·bar−1 for AO, SY and RB, respectively, for the rGO-ODA based TFN membrane. In fact, we hypothesize that the increase of the ethanol flux achieved with the use of rGO-ODA as a filler in TFN membranes is owing to a combination of the simultaneous presence of polar and non-polar groups from rGO-ODA nanosheets and the creation of still selective narrow gaps between these particles and the polyamide (PA)., Financial support from the Research Project MAT2016-77290-R (MINECO/AEI/FEDER, UE) is gratefully acknowledged. The Aragón Government (T43-17R) and the ESF is also gratefully acknowledged. Lorena Paseta would like to express her gratitude to the Spanish MINECO for the predoctoral grant (BES-2014-068287) awarded., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Nanofiltration thin-film composite membrane on either the internal or the external surface of a polysulfone hollow fiber

  • Echaide‐Górriz, Carlos
  • Malankowska, Magdalena
  • Téllez, Carlos
  • Coronas, Joaquín
The inner and outer surfaces of a porous hollow fiber polysulfone support are compared as substrates for the synthesis of polyamide thin‐film composite (TFC) membranes by interfacial polymerization. While both surfaces have pores common of microfiltration membranes, the inner surface has a larger pore diameter than the outer surface (2,700 nm compared to 950 nm). The inner TFC membrane showed higher water nanofiltration permeance than the outer (2.20 ± 0.17 compared to 0.13 ± 0.03 L m−2 hr−1 bar−1). This was due to the influence of the porosity and roughness, which were different on both support surfaces. These membranes are interesting because they were synthesized in a hollow fiber support with a high membrane area per volume unit (~6,900 m2/m3) and the substrate used was commercial, which means that the TFC membrane obtained is suitable for industrial application. A mathematical simulation of the nanofiltration run with COMSOL Multiphysics 5.3 software confirmed the experimental trends observed., Financial support from the Spanish MINECO and FEDER (MAT2016‐77290‐R), the Aragón Government (T43‐17R), and the ESF is gratefully acknowledged. C. Echaide‐Górriz thanks the Aragón Government for his PhD grant., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Polyamide/MOF bilayered thin film composite hollow fiber membranes with tuned MOF thickness for water nanofiltration

  • Echaide‐Górriz, Carlos
  • Zapata, José A.
  • Etxeberria-Benavides, Miren
  • Téllez, Carlos
  • Coronas, Joaquín
A bilayered polyamide-MOF membrane was synthesized on the inner surface of a hollow fiber support (200/350 mm ID/OD). The continuous MOF layer was prepared by liquid phase crystallization, and after that a polyamide layer was formed by interfacial polymerization on the top of the MOF. Firstly, the influence of time in the crystal growth of the MOF layer (from 15 to 120 min) was studied. The main characteristics of such MOF layer were tested (gas permeance and selectivity, and layer thickness measurements by SEM) to decide which of them were the optimum to support the polyamide thin film. The final bilayered membranes were characterized by SEM imaging and XPS and their performance was established in the nanofiltration of a solution of sunset yellow (450 Da) in water. Both permeance and selectivity were improved compared to a conventional TFC membrane (without the MOF layer): water permeance from 0.06 ± 0.01 to 0.24 ± 0.09 L·m−2·h−1·bar−1, and dye rejection from 88 ± 2 to 98 ± 1%)., Financial support from the Spanish Ministry of Science, Innovation and Universities and FEDER (Fondo Europeo de Desarrollo Regional) (MAT2016-77290-R), the Aragón Government (T43-17R) and the ESF is gratefully acknowledged. C. Echaide-Górriz thanks the Aragón Government for his PhD grant., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Sized-controlled ZIF-8 nanoparticle synthesis from recycled mother liquors: Environmental impact assessment

  • García Palacín, Marta
  • Martínez, José I.
  • Paseta, Lorena
  • Deacon, Adam
  • Johnson, Timothy
  • Malankowska, Magdalena
  • Téllez, Carlos
  • Coronas, Joaquín
The effect of different deprotonators as well as washing steps and drying procedure on the synthesis of ZIF-8 from the mother liquor was investigated. The morphology, thermal stability, crystallinity, and surface area of the synthesized MOF were investigated. In addition, life-cycle assessment (LCA) or, in other words, eco-balance, was implemented as well. LCA compares the full range of environmental effects associated with the product by evaluating all inputs and outputs of material flows and predicting how such flow will affect the environment. ZIF-8 nanocrystals were synthesized from the recycled mother liquors using NaOH or NH4OH thus preserving the main characteristics of the ZIF-8 nanoparticles derived from the initial synthesis. The rest of the characterization methods confirmed the suitability of the synthesis methodology considering the phase purity of the obtained ZIF-8 and nanometer size particles. This procedure enabled us not only to obtain phase pure ZIF-8 but also to substantially decrease the amount of solvent used for washing making it a sustainable process., This project has received funding from the European Union’s Horizon 2020 research and innovation program under grant agreement No 760944 (MEMBER project). Also, financial support from the Spanish Ministry of Science, Innovation and Universities and FEDER (MAT2016-77290-R), the Aragón Government (T43-17R) and the ESF is gratefully acknowledged., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Ultrathin permselective membranes: the latent way for efficient gas separation

  • Castro-Muñoz, Roberto
  • Agrawal, Kumar V.
  • Coronas, Joaquín
Membrane gas separation has attracted the attention of chemical engineers for the selective separation of gases. Among the different types of membranes used, ultrathin membranes are recognized to break the trade-off between selectivity and permeance to provide ultimate separation. Such success has been associated with the ultrathin nature of the selective layer as well as their defect-free structure. These membrane features can be obtained from specific membrane preparation procedures used, in which the intrinsic properties of different nanostructured materials (e.g., polymers, zeolites, covalent–organic frameworks, metal–organic frameworks, and graphene and its derivatives) also play a crucial role. It is likely that such a concept of membranes will be explored in the coming years. Therefore, the goal of this review study is to give the latest insights into the use of ultrathin selective barriers, highlighting and describing the primary membrane preparation protocols applied, such as atomic layer deposition, in situ crystal formation, interfacial polymerization, Langmuir–Blodgett technique, facile filtration process, and gutter layer formation, to mention just a few. For this, the most recent approaches are addressed, with particular emphasis on the most relevant results in separating gas molecules. A brief overview of the fundamentals for the application of the techniques is given. Finally, by reviewing the ongoing development works, the concluding remarks and future trends are also provided., R. Castro-Muñoz acknowledges the School of Science and Engineering and the FEMSA-Biotechnology Center at Tecnológico de Monterrey for their support through the Bioprocess (0020209I13) Focus Group. Financial support from the Spanish Ministry of Science, Innovation and Universities and FEDER (MAT2016-77290-R), the Aragón Government (T43-17R) and the ESF is also gratefully acknowledged. K. V. Agrawal acknowledges support from Swiss National Science Foundation (SNSF) Assistant Professor energy grant (PYAPP2_173645) and European Research Council (ERC) starting grant (805437 Ultimate Membranes)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Ultrathin films of porous metal–organic polyhedra for gas separation

  • Andrés, Miguel A.
  • Carné-Sánchez, Arnau
  • Sánchez-Laínez, Javier
  • Roubeau, Olivier
  • Coronas, Joaquín
  • Maspoch, Daniel
  • Gascón, Ignacio
Ultrathin films of a robust RhII‐based porous metal–organic polyhedra (MOP) have been obtained. Homogeneous and compact monolayer films (ca. 2.5 nm thick) were first formed at the air–water interface, deposited onto different substrates and characterized using spectroscopic methods, scanning transmission electron microscopy and atomic force microscopy. As a proof of concept, the gas separation performance of MOP‐supported membranes has also been evaluated. Selective MOP ultrathin films (thickness ca. 60 nm) exhibit remarkable CO2 permeance and CO2/N2 selectivity, demonstrating the great combined potential of MOP and Langmuir‐based techniques in separation technologies., This work was supported by the Spanish MINECO (projects RTI2018‐095622‐B‐I00, MAT2016‐78257‐R, MAT2016‐77290‐R and MAT2017‐86826‐R), the Catalan AGAUR (project 2017 SGR 328), the ERC under the EU‐FP7 (ERC‐Co 615954), the CERCA Program/Generalitat de Catalunya and the Aragon Government (T43_17R and E31_17R research groups). ICN2 is supported by the Severo Ochoa program from Spanish MINECO (SEV‐2017‐0706). A.C.‐S. thanks the Spanish MINECO for Juan de la Cierva fellowship (IJCI‐2016‐29802), J. S.‐L. and M.A.A thank the Spanish Education Ministry Program FPU2014 for their Ph.D. grants., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

The effect of hydrogen peroxide on the synthesis of terephthalate‐based metal‐organic frameworks

  • Monteagudo-Olivan, Rebeca
  • Jiménez‐Fernández, Isabel
  • López-Ram-de-Víu, Pilar
  • Sebastián, Víctor
  • Coronas, Joaquín
Metal‐organic frameworks (MOFs) are versatile materials for applications in fields including the environment, energy and health. A synthetic route for improving the formation of MOFs has been developed and is triggered by hydrogen peroxide (H2O2) to promote the formation of terephthalate‐based MOFs of MIL‐53 and MIL‐68 types, specifically those made from Fe3+ and Al3+ and mixtures of both. Different characterization techniques (TGA, XRD, SEM, TEM, N2 porosimetry and Raman, mass and NMR spectroscopies) gave insights into the effect of H2O2 on the MOF synthesis. The reaction yield was significantly improved (the highest yield being 74 % for MIL‐53(Al)), while crystallinity and N2 adsorption properties were mostly maintained for phases based on Al and Al/Fe. Furthermore, a reaction mechanism was envisaged from the mass spectroscopic analysis of the reaction solutions, thus suggesting that H2O2 plays the role of a μ‐hydroxo bridge promoter, favoring the link between terephthalate ligands and aluminum‐containing species to give rise to the μ‐carboxylate bridges, leading to a faster growth of the final MOF, and offering a novel MOF synthesis approach., The authors thank financial support from the Spanish MINECO and FEDER (MAT2016‐77290‐R), Aragón Government (T43‐17R & E102) and the People Program (CIG‐Marie Curie Actions, REA grant agreement no. 321642). CIBER‐BBN is an initiative funded by the VI National R&D&i Plan 2008–2011 financed by the Instituto de Salud Carlos III with the assistance of the European Regional Development Fund, Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Pebax® 1041 supported membranes with carbon nanotubes prepared via phase inversion for CO2/N2 separation

  • Sánchez-Laínez, Javier
  • Ballester-Catalán, Marcos
  • Javierre-Ortín, Enrique
  • Téllez, Carlos
  • Coronas, Joaquín
This work shows the preparation of Pebax® 1041 films from solutions in DMAc and water–DMAc emulsions as alternatives to those prepared by extrusion that can be found in the literature. These membranes were tested in post-combustion CO2 capture, in the separation of a 15/85 (v/v) CO2/N2 mixture. Self-supported membranes of Pebax® 1041 were prepared by solvent evaporation and phase inversion. The characterization of these films defined the intrinsic properties of this polymer in terms of chemical structure, crystallinity, thermal stability and gas separation performance (a CO2 permeability of 30 Barrer with a CO2/N2 selectivity of 21 at 35 °C and 3 bar feed pressure). Supported Pebax® 1041 membranes were also developed to decrease the Pebax® thickness (in the 1.5–10 μm range), resulting in a higher permeance. These membranes were prepared by a phase inversion process consisting of the precipitation of a Pebax® 1041/DMAc solution in water and dispersing it to form a stable emulsion that was drop-cast on PSF asymmetric supports. Once dried, the polymer formed a dense continuous layer. The phase inversion methodology is “greener” than solvent evaporation since dimethylacetamide is not released as toxic vapour during membrane preparation. The amount drop-cast led to a different selective layer thickness, which was enhanced by the dispersion of MWCNTs in the polymer emulsion. The properties of the Pebax® selective layer were studied by thermogravimetry and by measuring the contact angle of the membrane surface, and the optimal CO2/N2 selectivity (22.6) was obtained with a CO2 permeance of 3.0 GPU., Financial support from the Spanish Ministry of Science, the Research Projects MAT2016-77290-R (AEI/FEDER, UE) and T43-17R (the Aragón Government and the ESF) is gratefully acknowledged. J. Sánchez-Laínez also thanks the Spanish Education Ministry Program FPU2014 for his PhD grant., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Green preparation of thin films of polybenzimidazole on flat and hollow fiber supports: Application to hydrogen separation

  • Sánchez-Laínez, Javier
  • Etxeberria-Benavides, Miren
  • David, Oana
  • Téllez, Carlos
  • Coronas, Joaquín
This work shows the preparation of thin films, with thickness from 70 nm to 1 μm, of meta-polybenzimidazole (m-PBI) on polyimide P84 supports. Ethanolic solutions of m-PBI were used to coat flat and hollow fiber supports of asymmetric P84 with m-PBI in a process where the coating and drying was performed at room temperature. A solution of NaOH in EtOH allowed the dissolution of the m-PBI powder, providing the perfect coating solution to build thin films of m-PBI without damaging the polymeric support. It also meant a green alternative, avoiding the use of toxic solvents, such as dimethylacetamide. The resulting membranes have been tested for the separation of H2 mixtures at high temperature at different setups to allow checking their reproducibility. With 100 nm thickness the membranes showed their best gas separation performance. For flat membranes at 180 °C and 3 bar feed pressure a H2 permeance of 48.5 GPU was obtained, with respective H2/CO2 and H2/N2 selectivities of 33.3 and 55.8. Besides, the hollow fibers under a feed pressure of 6 bar and tested at the same temperature showed near 90 GPU of H2 with a H2/CO2 selectivity of 13.5 in the one-fiber module and over 39 GPU of H2 with a H2/CO2 selectivity of 20.2 in the five-fiber module. Finally, the stability of the membranes was proved for 22 days at 180 °C., Financial support from the Spanish Research Projects MAT2016-77290-R (MINECO/AEI, FEDER/UE), PID2019-104009RB−I00/AEI/10.13039/501100011033 and T43-17R (the Aragón Government and the ESF) is gratefully acknowledged., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Polyamide-MIL-101(Cr) thin films synthesized on either the outer or Inner surfaces of a polysulfone hollow fiber for water nanofiltration

  • Echaide‐Górriz, Carlos
  • Aysa-Martínez, Yolanda
  • Navarro, Marta
  • Téllez, Carlos
  • Coronas, Joaquín
High-performance thin film nanocomposite (TFN) hollow fiber (HF) membranes, with MIL-101(Cr) MOF nanoparticles (52 ± 13 nm) embedded, have been synthesized with the polyamide layer formed either on the outer or inner surface of a polysulfone HF (250 and 380 μm ID and OD, respectively). The TFN_out membrane was developed using the conventional interfacial polymerization method, typically applied to obtain TFN flat membranes (MOF particles added to the thin layer by deposition). This membrane gave a water permeance value of 1.0 ± 0.7 L·m–2·h–1·bar–1 and a rejection of 90.9 ± 1.2% of acridine orange (AO, 265 Da). In contrast, the TFN_in membrane was synthesized by microfluidic means and gave a significantly higher water permeance of 2.8 ± 0.2 L·m–2·h–1·bar–1 and a slightly lower rejection of 87.4 ± 2.5% of the same solute. This remarkable increase of flux obtained with small solute AO suggests that the HF membranes developed in this work would exhibit good performance with other typical solutes with higher molecular weight than AO. The differences between the performances of both TFN_in and TFN_out membranes lay on the distinct superficial physicochemical properties of the support, the synthesis method, and the different concentrations of MOF present in the polyamide films of both membranes. The TFN_in is more desirable due to its potential advantages, and more effortless scalability due to the microfluidic continuous synthesis. In addition, the TFN_in membrane needs much fewer quantities of reactants to be synthesized than the TFN_out or the flat membrane version., Financial support from the Research Projects MAT2016-77290-R (AEI/FEDER, UE) and PID2019-104009RB-I00/AEI/10.13039/501100011033, the Aragón Government (T43-20R), and the ESF are gratefully acknowledged. C.E. -G. thanks the Aragón Government for his PhD grant., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

An evolving insight into metal organic framework-functionalized membranes for water and wastewater treatment and resource recovery

  • Le, Tin
  • Chen, Xi
  • Dong, Hang
  • Tarpeh, William
  • Perea-Cachero, Adelaida
  • Coronas, Joaquín
  • Martin, Stephen M.
  • Mohammad, Munirah
  • Razmjou, Amir
  • Esfahani, Amirsalar R.
  • Koutahzadeh, Negin
  • Cheng, Peifu
  • Kidambi, Piran R.
  • Rabbani Esfahani, Milad
Metal organic frameworks (MOFs) represent one of the largest classes of porous crystalline materials. MOFs have been increasingly applied as functionalizing agents for membranes because of their porosity, high surface area, small particle size, aspect ratio control, tuneability, compatibility with a polymeric network, and exuberance of diverse functional groups. In this comprehensive review paper, we discuss achievements, opportunities, and challenges related to the functionalization of different types of membranes using MOFs for water and wastewater treatment and desalination. The current synthesis and fabrication approaches of MOF-functionalized membranes were identified and critically reviewed. The effects of MOFs on membrane performance, including permeation, selectivity, and antifouling, were discussed. Also, the application of MOF-functionalized membranes in aqueous environments for conventional applications such as heavy metal removal and emerging applications such as resource recovery was enunciated. Finally, recommendations and future directions were provided for further improvement in the field of MOF-functionalized membranes for water treatment and reuse., The authors would like to acknowledge the financial support of the National Science Foundation (NSF) under Grant No. 1941700 and NSF Career No. 1944134 and to the Department of the Interior (DOI), Bureau of Reclamation (BR) under Agreement No. R19AC00087. The authors would like to acknowledge the financial support of the United States Geological Survey (USGS) under Sponsor No. 20-WRC207214 and to the Environmental Protection Agency (EPA) under Award No. 84014501. The financial Spanish Research Projects MAT2016-77290-R (MINECO/AEI, FEDER/UE), PID2019-104009RB-I00 (MICINN/AEI, FEDER/UE), and T43-20R (the Aragón Government and the ESF) are gratefully acknowledged., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Metal organic framework top-down and bottom-up patterning techniques

  • Ruiz-Zambrana, César L.
  • Malankowska, Magdalena
  • Coronas, Joaquín
Metal organic frameworks (MOFs) have recently attracted considerable research interest in several fields from coordination chemistry and materials science to engineering and medicine not only due to energy and environmental issues but also due to the need for new paradigms of efficiency and sustainability according to the requirements of the 21st century global society. Because of their crystalline and organic–inorganic nature, they are able to crystallize constituting intergrown architectures ductile enough to be patterned, with the use of appropriate techniques, as nano- and micro-devices with multiple applications. This perspective comprehensively summarizes the recent state of the art in the use of top-down and bottom-up methodologies to create MOF structures with a defined pattern at the nano- and micro-scale., Financial support from the Spanish Research Projects MAT2016-77290-R (MINECO/AEI, FEDER/UE), PID2019-104009RB-I00/AEI/10.13039/501100011033 and T43-20R (the Aragón Government and the ESF) is gratefully acknowledged., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Microplastics in marine environment: a review on sources, classification, and potential remediation by membrane technology

  • Malankowska, Magdalena
  • Echaide‐Górriz, Carlos
  • Coronas, Joaquín
The presence of microplastics in marine environment has been a pollution problem for years; however, people have only recently become aware of it, similar to the situation in the last few decades with global warming due to greenhouse gases. Microplastics are pollutants that are highly stable to complete biodegradation, and there is a high risk that they can enter the food chain (e.g. fish or agriculture products) because of the fact that secondary plastics (in principle, as small as monomers and oligomers) generated from the evolution of primary plastics (that directly spread in the environment) require more specific separation processes for their removal. In this review, firstly, we focus on the classification of microplastics and potential remediation technologies to be applied depending on their size. Secondly, membrane technologies (microfiltration, ultrafiltration and nanofiltration) are presented in the context of microplastics removal, revealing their suitability for the task and a future path of research and development to be carried out to mitigate the problem., Financial support from the Spanish Research Projects MAT2016-77290-R (MINECO/AEI, FEDER/UE), PID2019-104009RB-I00 (MICINN/AEI, FEDER/UE) and T43-20R (the Aragón Government and the ESF) is gratefully acknowledged., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Vapor phase interfacial polymerization: a method to synthesize thin film composite membranes without using organic solvents

  • Paseta, Lorena
  • Echaide‐Górriz, Carlos
  • Téllez, Carlos
  • Coronas, Joaquín
Thin film composite membranes (TFC) of polyamide (PA) prepared by interfacial polymerization (IP) between a diamine and an acyl chloride are applied to industrial nanofiltration and reverse osmosis. Water, to dissolve the diamine, and n-hexane, to dissolve the acyl chloride, solvents are involved in the IP process. Eliminating the use of n-hexane would be crucial to produce a greener TFC membrane synthesis method. This is achieved here by carrying out an interfacial polymerization from the vapor phase. First, the membrane support was impregnated with the aqueous diamine solution. Second, the support with the diamine was contacted with vapors of the acyl chloride to unchain the IP reaction. Besides the absence of n-hexane, acyl chloride was applied more efficiently avoiding its loss during the cleaning operations carried out in the typical IP process. These membranes were applied in the nanofiltration of simulated micropollutants in water (rose Bengal, sunset yellow and acridine orange dyes), with higher water permeance (up to 3.3 L·m−2·h−1·bar−1) than that of conventional TFC membranes and dye rejections higher than 94% in all cases., Financial support from the Research Projects MAT2016-77290-R (AEI/FEDER, UE) and the PID2019-104009RB-I00/AEI/10.13039/501100011033, the Aragón Government (T43-20R) are gratefully acknowledged. All of the microscopy work was done in the Laboratorio de Microscopías Avanzadas at the Instituto de Nanociencia y Materiales de Aragón (LMA-INMA). The authors acknowledge the LMA-INA for offering access to their instruments and expertise., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Phase inversion method for the preparation of Pebax® 3533 thin film membranes for CO2/N2 separation

  • Martínez-Izquierdo, Lidia
  • Malankowska, Magdalena
  • Téllez, Carlos
  • Coronas, Joaquín
Thin film composite membranes of poly(ether-block-amide) copolymer Pebax® 3533 were prepared for the first time on asymmetric polysulfone supports by a phase inversion method. The casting solution concentration and the number of layers were varied to study their influence on the selective layer thickness and the gas separation performance. The casting solution concentrations of polymer dissolved in the 1-propanol/1-butanol mixture were 0.25, 0.5, 1.0 and 1.5 wt%. These conditions produced membranes with selective skin layers with thicknesses from 0.2 to 1.8 µm. All the membranes were characterized by scanning electron microscopy, thermogravimetric analysis and infrared spectroscopy. Furthermore, the intrinsic viscosity of all the casting solutions was studied to understand the effect of the polymer concentration on the homogeneity and the gas separation properties of the obtained membranes. In general, lower viscosity of casting solutions rendered to more defective skin layers, resulting in a higher number of layers required to obtain selective membranes. The gas separation performance was tested for the post-combustion 15/85 CO2/N2 mixture at 25–50 °C and under a feed pressure of 3 bar. The best separation performance was achieved with the 0.5 wt% casting solution membranes after the deposition of four polymer layers, obtaining a CO2 permeance of 127 GPU and a CO2/N2 selectivity of 21.4 at 35 °C, the same selectivity of the corresponding dense membrane but with much higher permeance., Financial support from the Spanish Research Projects MAT2016-77290-R (MINECO/AEI, FEDER/UE), PID2019‐104009RB−I00/AEI/10.13039/501100011033 (Agencia Estatal de Investigación, Spain) and T43-20R (the Aragón Government and ESF) is gratefully acknowledged. L. Martínez-Izquierdo also thanks the Aragón Government (DGA) for her PhD grant. All microscopy work was done in the Laboratorio de Microscopías Avanzadas at the Instituto de Nanociencia de Aragón (LMA-INA)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Solventless synthesis of ZIF-L and ZIF-8 with hydraulic press and high temperature

  • Pérez-Miana, Marta
  • Reséndiz-Ordóñez, Javier U.
  • Coronas, Joaquín
In recent years, alternative methods to conventional synthesis of MOFs (metal-organic frameworks) have emerged due to the problematic use of solvents for both the environment and human health. Here we present the synthesis of ZIFs (zeolitic imidazolate frameworks) at high pressure by means of a hydraulic press provided with a heating mechanism. By the optimization of parameters such as temperature, time and the addition of promotor NH4NO3, a considerable increase in the reaction yield was achieved in products, neither washed nor activated, obtained since the first minute of reaction. Depending on the operation conditions, ZIF-L appeared as competing phase with ZIF-8. Upon transformation of ZIF-L into ZIF-8 in presence of ethanol, a reaction yield of 58.2% was achieved to highly crystalline ZIF-8 with a BET specific surface area of 947 m2/g. This green, fast, versatile and improved method suggests a possible way to future synthesis of other MOFs and the possibility of their industrial implementation., Financial support from the Research Projects MAT2016-77290-R and the PID2019-104009RB-I00/AEI/10.13039/501100011033 (Spanish AEI/FEDER, UE), the Aragón Government (T43-20R and Marta Pérez-Miana PhD grant) and the ESF are gratefully acknowledged. All the microscopy work was done in the Laboratorio de Microscopías Avanzadas (LMA). The authors acknowledge the LMA for offering access to their instruments and expertise and the Servicios de Apoyo a la Investigación (SAI), both from the Universidad de Zaragoza., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Mesoporous Sn-In-MCM-41 catalysts for the selective sugar conversion to methyl lactate and comparative life cycle assessment with the biochemical process

  • Iglesia, Óscar de la
  • Sarango, Miryam
  • Munárriz, Mikel
  • Malankowska, Magdalena
  • Navajas, Alberto
  • Gandía, Luis M.
  • Coronas, Joaquín
  • Téllez, Carlos
The use of biomass for the production of energy and higher added value products is a topic of increasing interest in line with growing environmental concerns and circular economy. Mesoporous material Sn-In-MCM-41 was synthesized for the first time and used as a catalyst for the transformation of sugars to methyl lactate (ML). This catalyst was characterized in depth by various techniques and compared with Sn-MCM-41 and In-MCM-41 catalysts. In the new Sn-In-MCM-41 material, both metals, homogeneously distributed throughout the mesoporous structure of MCM-41, actuate in a cooperative way in the different steps of the reaction mechanism. As a result, yields to ML of 69.4 and 73.9% in the transformation of glucose and sucrose were respectively reached. In the case of glucose, the ML yield 1.5 and 2.6 times higher than those of Sn-MCM-41 and In-MCM-41 catalysts, respectively. The Sn-In-MCM-41 catalyst was reused in the transformation of glucose up to four cycles without significant loss of catalytic activity. Finally, life cycle assessment comparison between chemical and biochemical routes to produce ML allowed us to conclude that the use of Sn-In-MCM-41 reduces the environmental impacts compared to Sn-MCM-41. Nevertheless, to make the chemical route comparable to the biochemical one, improvements in the catalyst and ML synthesis have to be achieved., Financial support from the Grant MAT2016-77290-R funded by MCIN/AEI/10.13039/501100011033 and by “ERDF A way of making Europe”, and Grant T43-20R funded by the Aragón Government are gratefully acknowledged. The authors would like to acknowledge Dr. Elena Serrano from Centro Universitario de la Defensa Zaragoza for her contribution (preparation of materials and solutions for titration of catalysts) in this work. The authors would like to acknowledge the use of the Servicio General de Apoyo a la Investigación-SAI and the use of instrumentation as well as the technical advice provided by the National Facility ELECMI ICTS, node “Laboratorio de Microscopias Avanzadas” at the University of Zaragoza. A.N. and L.M.G. gratefully acknowledge the financial support from Spanish Ministerio de Ciencia, Innovación y Universidades, and the Grant RTI2018-096294-B-C31 funded by ERDF/FEDER. L.M.G. also thanks Banco Santander and Universidad Pública de Navarra for their financial support under “Programa de Intensificación de la Investigación 2018” initiative., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

A new zeolitic hydroxymethylimidazolate material and its use in mixed matrix membranes based on 6FDA-DAM for gas separation

  • Perea-Cachero, Adelaida
  • Sánchez-Laínez, Javier
  • Berenguer-Murcia, Ángel
  • Cazorla-Amorós, Diego
  • Téllez, Carlos
  • Coronas, Joaquín
The new ZIF named UZAR-S13 is formed by Zn2+ and 4(5)-(hydroxymethyl)imidazolate. UZAR-S13 has two distinct phases according to SEM and XRD: amorphous spheres and sheet crystals. UZAR-S13 and byproducts, with no N2 adsorption, rendered a notable CO2 uptake (up to 3.8 mmol g−1 at 30 bar and 0 °C), approaching values of known ZIFs. The most promising materials were included as fillers in mixed matrix membranes based on copolyimide 6FDA-DAM to study the separation of CO2/CH4, CO2/N2, H2/CO2 and H2/CH4 mixtures. The pore blocking hindered the gas flow of bulky molecules (CH4, N2 and CO2). The high CO2 adsorption on sheet crystals also contributed to the decrease in the permeability of CH4, N2 and CO2, giving poor selectivities. In contrast, the MMMs improved both the H2/CH4 selectivity (8.9–12.7 vs. 7.2) and permeability of H2 (544–597 vs. 505 Barrer) of the bare 6FDA-DAM membrane. This emphasizes the potential application of the fillers in the separation by molecular sieving of gas mixtures without CO2., Financial support from the Spanish Ministry of Economy and Competitiveness (MINECO) and FEDER (MAT2013-40556-R, MAT2016-77290-R (MINECO/FEDER) and CTQ2015-66080-R (MINECO/FEDER)), the European Social Fund (ESF) and the Aragón Government (DGA, T05) is gratefully acknowledged. A. P.-C. and J. S.-L. also thank the DGA and Spanish Education Ministry Program FPU2014, respectively, for Ph.D. grants. The microscopy work was carried out in the Laboratorio de Microscopías Avanzadas at the Instituto de Nanociencia de Aragón (LMA-INA, Universidad de Zaragoza). The authors would like to acknowledge the use of the Servicio General de Apoyo a la Investigación-SAI (Universidad de Zaragoza)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Antioxidant activity of the essential oil of citrus limon before and after its encapsulation in amorphous SiO2

  • Himed, Louiza
  • Merniz, Salah
  • Monteagudo-Olivan, Rebeca
  • Barkat, Malika
  • Coronas, Joaquín
In recent years, the consumer demand for natural ingredients has resulted in sustained growth in the global market of essential oils. Indeed, essential oils are considered today as a product "trend" to the general public, which in particular raises considerable appeal from the agro-food sector. However, this application sector has to face many disadvantages related to the variability of their composition, and their volatility and storage instability., The objective of this work was to extract the essential oil of Citrus limon, determine its chemical composition, evaluate its antioxidant activity and see the effect of its encapsulation on such activity. The cold pressing of the lemon peel yielded 1.24±0.07% of the essential oil. This oil was characterized by a composition rich in limonene (67.1%) followed by α-pinene (11.0%) and α-terpinene (8.0%).The antioxidant activity of the oil expressed by the antiradical power DPPH and by the reducing power CUPRAC gave rise to results comparable to that of the standards. The encapsulation of this oil in silica did not modify its antioxidant activity. The thermogravimetric analysis showed a weak thermal estabilization of the encapsulated oil compared to the free oil. FTIR-ATR showed that the encapsulation did not alter the composition of the oil., Financial support from the Spanish MINECO and FEDER (MAT2016-77290-R), the Aragón Government (T05), the ESF and the Ministry of Higher Education and Scientific Research of Algeria is gratefully acknowledged., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Asymmetric polybenzimidazole membranes with thin selective skin layer containing ZIF-8 for H 2 /CO 2 separation at pre-combustion capture conditions

  • Sánchez-Laínez, Javier
  • Zornoza, Beatriz
  • Téllez, Carlos
  • Coronas, Joaquín
This work addresses an optimization in the fabrication of flat PBI membranes containing ZIF-8 nanoparticles for gas separation purposes. The PBI membranes were prepared in an asymmetric configuration on P84® supports, representing a new way of preparing flat PBI membranes. An optimization of the conditions for the PBI phase inversion preparation method, including the dope composition (in the 15–26 wt% range), has been carried out to obtain PBI membranes with a 1 µm selective skin layer. The asymmetric membranes showed an unprecedented gas separation capacity in pre-combustion CO2 capture, much superior to that of dense membranes, under harsh operating conditions (250 °C and 6 bar feed), performing up to 20.3 GPU of H2 and a H2/CO2 selectivity of 35.6. Their much thinner selective layer made possible the increase in selectivity because of the saturation of the CO2 flow at high pressures. The reduction in the amount of ZIF-8 for obtaining a membrane with the same filler loading (3.7 vs. 9.3 g/m2) was also possible; the performance of this ZIF-8 containig membrane was 22.4 GPU of H2 and a H2/CO2 selectivity of 22.3. The activation energy of the membranes, as well as the flow resistances, were calculated, providing a resistance in series model to understand the flow inside the membrane., The research leading to these results has received funding from the European Union Seventh Framework Programme (FP7/2007–2013) under grant agreement n° 608490, project M4CO2. In addition, financial support from the Spanish MINECO and FEDER (MAT2016-77290-R), the Aragón Government (T05) and the ESF is gratefully acknowledged. J. S-L. thanks the Spanish Education Ministry Program FPU2014 for his Ph.D. grant. All the microscopy work was done in the Laboratorio de Microscopías Avanzadas at the Instituto de Nanociencia de Aragón (LMA-INA). Finally, the authors would like to acknowledge the use of the Servicio General de Apoyo a la Investigación-SAI, Universidad de Zaragoza., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Controlled deposition of MOFs by dip-coating in thin film nanocomposite membranes for organic solvent nanofiltration

  • Sarango Simbaña, Lilian
  • Paseta, Lorena
  • Navarro, Marta
  • Zornoza, Beatriz
  • Coronas, Joaquín
ZIF-8 and ZIF-67 particles, with sizes of 70 ± 10 nm and 240 ± 40 nm, respectively, were deposited by dip-coating on top of polyimide P84® asymmetric supports. In the best conditions, this gives rise to a MOF (metal-organic framework) monolayer which remains on the polyimide support during the interfacial polymerization of polyamide carried out to produce a thin film nanocomposite membrane for organic solvent nanofiltration (OSN). This method is simple, shorter and is environmentally friendly, since no excess MOF is lost during the interfacial polymerization, exhibiting good OSN results: dye rejection of 90% together with a high methanol permeance of 8.7 L m−2 h−1 bar−1., Financial support from the Spanish Ministry of Economy and Competitiveness (MINECO) and FEDER (MAT2016-77290-R), the European Social Fund (ESF) and the Aragón Government (DGA, T05) is gratefully acknowledged. L.S. and L.P. are also grateful for respective Ph.D. grants from Becas Santander Universidades and Spanish MINECO FPI Program. The microscopy work was carried out in the Laboratorio de Microscopías Avanzadas at the Instituto de Nanociencia de Aragón (LMA-INA, Universidad de Zaragoza). The use of the Servicio General de Apoyo a la Investigación-SAI (Universidad de Zaragoza) is also acknowledged., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Enhanced gas separation performance of 6FDA-DAM based mixed matrix membranes by incorporating MOF UiO-66 and its derivatives

  • Ahmad, Mohd Zamidi
  • Navarro, Marta
  • Zornoza, Beatriz
  • Téllez, Carlos
  • Semino, Rocio
  • Maurin-Pasturel, Guillaume
  • Coronas, Joaquín
et al., Functionalization and post-synthetic modification (PSM) of metal-organic frameworks (MOFs) are two important routes to obtain MOFs with full potential in mixed matrix membrane (MMM) fabrication. We synthesized UiO-66 and two derivatives UiO-66-NH2 and UiO-66-NH-COCH3 with less than 50 nm particle size. The CO2 uptakes at 10 bar in the two functionalized UiO-66s were improved by 44% and 58%, respectively, with respect to the pristine solid. The MOF nanoparticles were incorporated into the highly permeable polymer 6FDA-DAM, making MMMs with 5–24 wt% particle loadings. All fillers and membranes were characterized accordingly, and their gas separation performances were evaluated by feeding CO2/CH4 equimolar mixtures at 2 bar pressure difference at 35 °C. CO2 permeability (PCO2) of pristine 6FDA-DAM (PCO2 = 997 ± 48 Barrer, αCO2/CH4 = 29 ± 3) increased by 92% with 20 wt% UiO-66 loading, while maintaining the CO2/CH4 selectivity. Improvements of 23% and 27% were observed for PCO2 with the same 20 wt% loading of UiO-66-NH2 and UiO-66-NH-COCH3, respectively. The αCO2/CH4 was improved up to 16% using both functionalized UiO-66 type MOFs. The best separation performance in this work was obtained with 14 wt% UiO-66 MMM (PCO2 = 1912 ± 115 Barrer, αCO2/CH4 = 31 ± 1), 16 wt% UiO-66-NH2 MMM (PCO2 = 1223 ± 23 Barrer, αCO2/CH4 = 30 ± 1) and 16 wt% UiO-66-NH-COCH3 MMM (PCO2 = 1263 ± 42 Barrer, αCO2/CH4 = 33 ± 1) at 2 bar feed pressure difference. The measurement was also conducted with various binary compositions (CO2 = 10 – 90%), both at low and high pressures up to 40 bar at 35 °C, showing no pressure-related CO2-induced plasticization. The atomistic modelling for the MOF/polymer interface was consistent with a moderate MOF surface coverage by 6FDA-DAM which did not play a detrimental role in the membrane performance., The authors acknowledge the financial support of EACEA/European Commission, within the “Erasmus Mundus Doctorate in Membrane Engineering – EUDIME” (ERASMUS MUNDUS Programme 2009–2013, FPA n. 2011-0014, SGA n. 2012-1719), Operational Programme Prague – Competitiveness (CZ.2.16/3.1.00/24501), “National Program of Sustainability” of Czech Republic, (NPU I LO1613) MSMT-43760/2015 and MAT2016–77290-R from the Spanish MINECO and FEDER, the Aragón Government (DGA, T05) and the European Social Fund. The microscopy work was carried out in the Laboratorio de Microscopías Avanzadas at the Instituto de Nanociencia de Aragón (LMA-INA, Universidad de Zaragoza)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Enhancement of CO2/CH4 separation performances of 6FDA-based co-polyimides mixed matrix membranes embedded with UiO-66 nanoparticles

  • Ahmad, Mohd Zamidi
  • Navarro, Marta
  • Lhotka, Miloslav
  • Zornoza, Beatriz
  • Téllez, Carlos
  • Fíla, Vlastimil
  • Coronas, Joaquín
Metal-organic frameworks (MOFs) incorporation into mixed matrix membranes (MMMs) is gaining more attention due to the combined advantages of high separation performance and easy processability. Nanoparticles (NPs) of CO2-philic MOF UiO-66 (Zr-BDC) were synthesized with high surface area and ca. 50 nm particle size (and also for comparison with 100 and 200 nm sizes). They were incorporated into three 6FDA-based co-polyimides (namely 6FDA-BisP, 6FDA-ODA, and 6FDA-DAM), forming MMMs with loadings in the 4–23 wt% range. The NPs and MMMs were characterized accordingly by XRD, BET, SEM, TEM, FTIR, and TGA. CO2 and CH4 isotherms on the NPs were measured by a static volumetric method at the pressure up to 10 bar. Fractional free volume (FFV) was calculated using solid density, measured by pycnometer. Gas separation performance was evaluated using a feed composition of 50%:50% CO2:CH4 binary mixture at 35 °C and a pressure difference of 2 bar. The presence of UiO-66 NPs in the continuous 6FDA-BisP and 6FDA-ODA co-polyimides improved both CO2 permeability and CO2/CH4 selectivity by 50–180% and 70–220%, respectively. In the case of 6FDA-DAM MMMs, the CO2 permeability was significantly improved by 92%, while maintaining the CO2/CH4 selectivity. The best results in terms of CO2/CH4 selectivity were 41.9 for 6FDA-BisP (17 wt% filler loading, 108 Barrer of CO2), 57.0 for 6FDA-ODA (7 wt% filler loading, 43.3 Barrer of CO2) and 32.0 for 6FDA-DAM (8 wt% filler loading, 1728 Barrer of CO2)., The authors acknowledge the financial support of EACEA/European Commission, within the “Erasmus Mundus Doctorate in Membrane Engineering – EUDIME” (ERASMUS MUNDUS Programme 2009-2013, FPA n. 2011-0014, SGA n. 2012-1719), Operational Programme Prague – Competitiveness (CZ.2.16/3.1.00/24501), “National Program of Sustainability“ of Czech Republic, (NPU I LO1613) MSMT-43760/2015 and (MAT2016-77290-R) from the Spanish MINECO and FEDER, the Aragón Government (DGA, T05) and the European Social Fund. The microscopy work was carried out in the Laboratorio de Microscopías Avanzadas at the Instituto de Nanociencia de Aragón (LMA-INA, Universidad de Zaragoza). The authors would like to acknowledge the use of the Servicio General de Apoyo a la Investigación-SAI (Universidad de Zaragoza)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Enhancement of growth of MOF MIL-68(Al) thin films on porous alumina tubes using different linking agents

  • Perea-Cachero, Adelaida
  • Calvo, Pablo
  • Romero, Enrique
  • Téllez, Carlos
  • Coronas, Joaquín
The preparation of MIL-68(Al) films on the inner surface of alumina tubes is reported. As the direct deposition of the MOF on bare alumina gives poor adhesion results, three different linking agents are employed to achieve a good MOF–support interaction. Colloidal silica LUDOX®, zeolite silicalite-1, and natural polysaccharide chitosan are chosen as binders, because they contain potential functional groups (hydroxy, amino, ether), which can establish hydrogen bonds. While colloidal silica leads to noncontinuous MOF layers, silicalite-1 and chitosan give rise to uniform and well-anchored films, as confirmed by the different characterization techniques used to study the MOF layer. Single-gas permeation experiments are carried out to determine the quality and ideal efficiency of the membranes prepared with silicalite-1 and chitosan. The results for the MIL-68(Al)/silicalite-1 membranes evidence the existence of macrodefects. However, no cracks are found when chitosan is used as a linking agent, and the gas flow through the MIL-68(Al)/chitosan membranes clearly follows Knudsen diffusion., The authors acknowledge financial support from the Spanish Ministry of Economy and Competitiveness (MAT2013-40556-R, MAT2016-77290-R), the Aragón Government (DGA, T05), the European Social Fund (ESF) and FEDER. A. P.-C. also thanks the DGA for a Ph.D. grant. The microscopy work was carried out in the Laboratorio de Microscopías Avanzadas at the Instituto de Nanociencia de Aragón (LMA-INA, Universidad de Zaragoza). The authors would like to acknowledge the use of the Servicio General de Apoyo a la Investigación-SAI (Universidad de Zaragoza)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Homogeneous thin coatings of zeolitic imidazolate frameworks prepared on quartz crystal sensors for CO2 adsorption

  • Sarango Simbaña, Lilian
  • Benito, Javier
  • Gascón, Ignacio
  • Zornoza, Beatriz
  • Coronas, Joaquín
Thin films of four zeolitic-imidazolate frameworks (ZIF-8, ZIF-67, ZIF-7, and ZIF-93) have been fabricated by a dip-coating method on glass and quartz crystal microbalance (QCM) substrates. Homogeneous coatings with sizes of crystals of 65 ± 20, 285 ± 96, 61 ± 20 and 72 ± 21 nm for ZIF-8, ZIF-67, ZIF-7, and ZIF-93, respectively, were obtained. Upon characterization of the ZIFs and coatings by XRD, TGA, SEM, FTIR, contact angle measurement and N2 adsorption, the coatings were exposed to vapors of dichloromethane for activation. The CO2 adsorption of the coatings was then studied using a QCM device., Financial support from the Spanish Ministry of Economy and Competitiveness and FEDER (MAT2016-77290-R), the European Social Fund and the Aragón Government ( DGA, T05) is gratefully acknowledged. L.S. is also grateful for a Ph.D. grant from Becas Santander Universidades. The microscopy work was carried out in the Laboratorio de Microscopías Avanzadas at the Instituto de Nanociencia de Aragón (LMA-INA, Universidad de Zaragoza)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Hydrogen separation at high temperature with dense and asymmetric membranes based on PIM-EA(H2)-TB/PBI blends

  • Sánchez-Laínez, Javier
  • Zornoza, Beatriz
  • Carta, Mariolino
  • Malpass-Evans, Richard
  • McKeown, Neil B.
  • Téllez, Carlos
  • Coronas, Joaquín
The preparation of dense and asymmetric flat membranes from the blending of polybenzimidazole (PBI) and (1.5–20 wt %) of a polymer of intrinsic microporosity (PIM-EA(H2)-TB) is reported. Thermal characterization validated the blend by revealing a single glass transition temperature, which suggests the absence of polymer phase segregation. In addition, the decomposition activation energy and d-spacing of the blends follow trends that correlate with the amount of PIM component. The membranes have been tested for the separation of H2/CO2 mixtures. The properties of the dense membranes, which also incorporate zeolitic imidazolate-8 (ZIF-8) nanoparticles, helped understanding of the behavior of the PIM/PBI blends by which phase inversion results in high separation performance asymmetric membranes. Asymmetric membranes show H2/CO2 selectivities of 23.8 (10/90 wt % PIM/PBI) and 19.4 (20/80 wt % PIM/PBI) together with respective H2 permeances of 57.9 and 83.5 GPU at 250 °C and 6 bar feed pressure. The gas separation performance of these asymmetric blends has been fitted to an empirical model, showing the influence of the amount of PIM and the feed pressure., The research comprising this work has received financial support from the European Union Seventh Framework Programme (FP7/2007-2013) under Grant Agreement No. 608490, project M4CO2. In addition, the authors acknowledge the funding received from the Spanish MINECO and FEDER (MAT2016-77290-R), the Aragón Government (T43-17R), and the European Social Fund. J.S-L. in particular thanks the Spanish Education Ministry Program FPU2014., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Insight into the reversible structural crystalline-state transformation from MIL-53(Al) to MIL-68(Al)

  • Perea-Cachero, Adelaida
  • Romero, Enrique
  • Téllez, Carlos
  • Coronas, Joaquín
The reversible crystalline transformation between MIL-53(Al) and MIL-68(Al) is described. This followed a uniform conversion model with cleavage and formation of metal–ligand bonds after exchange or removal of guest molecules. MIL-68(Al) materials produced during the transformations had higher thermal stability and crystallinity than the as-synthesized MIL-68(Al)., Financial support from the Spanish Ministry of Economy and Competitiveness (MINECO) and European Regional Development Fund (MAT2013-40556-R, MAT2016-77290-R), ESF and the Aragón Government (DGA, T05) is gratefully acknowledged. A. P.-C. also thanks the DGA for a Ph.D. grant. The authors would like to acknowledge the use of the Servicio General de Apoyo a la Investigación-SAI (Universidad de Zaragoza (UZ)) and the Laboratorio de Microscopías Avanzadas at INA (LMA-INA, UZ)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

New strategies based on microfluidics for the synthesis of metal-organic frameworks and their membranes

  • Echaide‐Górriz, Carlos
  • Clément, Coralie
  • Cacho-Bailo, Fernando
  • Téllez, Carlos
  • Coronas, Joaquín
Metal–organic frameworks (MOFs) are highly porous crystalline materials formed by the coordination of organic ligands with metal clusters. Despite the significant progress in their development over the last few years and their applications in various classic and emerging fields, the control of their shape and size remains a challenge, in particular the search for more efficient and environmentally friendly syntheses. In this context, the microfluidics approach allows not only the continuous production of MOFs but also an accurate reaction parameter control in their synthesis, representing a step towards intensification, versatility and scalability in the use of MOFs. Microfluidics also offers the possibility of synthesizing effective and defect free MOF-based hollow fiber membranes saving reactants as compared to conventional methods. This review is devoted to highlighting the multitude of synergies appearing when dealing with MOFs and microfluidics, not only in the bare synthesis of MOFs and their hierarchical structures but also when fabricating hollow fiber membranes with important applications in the separation field., Financial support from the Spanish MINECO and FEDER (MAT2016-77290-R), the Aragón Government (T05) and the ESF is gratefully acknowledged. C. E.-G. thanks the Aragón Government for his PhD grant., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Pervaporation-assisted esterification reactions by means of mixed matrix membranes

  • Castro-Muñoz, Roberto
  • Iglesia, Óscar de la
  • Fíla, Vlastimil
  • Téllez, Carlos
  • Coronas, Joaquín
The incorporation of fillers into polymeric membranes, producing mixed matrix membranes (MMMs), is considered a promising way to improve their separation performance. As an alternative method for the dehydration of organics, pervaporation (PV) technology has recently begun to be implemented to assist esterification reactions, in which the water generated is identified as a limitation to further conversion efficiency. In this regard, the present review conveys the evidence from recent literature reports about PV-assisted esterification reactions. Therefore, a particular emphasis will be placed on the enhancements provided by MMMs. Moreover, some key principles regarding the selection of fillers suitable for synergistic effects on water removal are mentioned. In addition, generalities of PV, including the theoretical aspects and its role in separation, are discussed. Finally, an outlook on the future directions based on the latest findings on PV-assisted esterification reactions by means of MMMs is provided, as well as a viewpoint concerning the relationship between the “Twelve Principles of Green Chemistry” and PV technology., R. Castro-Muñoz acknowledges the European Commission - Education, Audiovisual and Culture Executive Agency (EACEA) for his Ph.D. scholarship under the program Erasmus Mundus Doctorate in Membrane Engineering – EUDIME (FPA No 2011-0014, Edition V, http:/eudime.unical.it). This work was partially supported by the Operational Program Prague – Competitiveness (CZ.2.16/3.1.00/24501), the “National Program of Sustainability“ (NPU I LO1613) MSMT-43760/2015), and by financial support from specific university (Prague University) research (IGA 2017, MSMT No 20-SVV/2017). Financial support from the Spanish MINECO and FEDER (MAT2016-77290-R) and the Aragón Government (T05) is also gratefully acknowledged., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Polymer-stabilized percolation membranes based on nanosized zeolitic imidazolate frameworks for H2/CO2 separation

  • Sánchez-Laínez, Javier
  • Friebe, Sebastian
  • Zornoza, Beatriz
  • Mundstock, Alexander
  • Strauß, Ina
  • Téllez, Carlos
  • Caro, Jürgen
  • Coronas, Joaquín
This work shows the preparation of self-supported composite membranes prepared with the nano-sized zeolitic imidazolate frameworks (ZIFs): ZIF-8, ZIF-7(III) and ZIF-7/8 core-shells. The membranes consist of compressed pellets of ZIF nanoparticles (up to 74 wt% loading) stabilized with gas-impermeable epoxy resin, providing a gas transport-selective percolation network named polymer-stabilized percolation membrane (PSPM). The different PSPMs have been characterized by SEM, TGA, XRD, FTIR and Raman. FIB/SEM has provided a 3D reconstruction of the composite thanks to the slice and view technique, allowing a perfect visualization of the inside of the network. The N2 adsorption properties have also been studied and compared with those of ZIFs in powder state. The gas separation performance of these membranes has been tested for the H2/CO2 mixture. The PSPMs were tested with feed pressures up to 5 bar, obtaining H2 permeabilities of hundreds of Barrer and a maximum H2/CO2 selectivity of 12.3., The research leading to these results has received funding from the European Union Seventh Framework Programme (FP7/2007-2013) under grant agreement n° 608490, project M4CO2. Financial support from the Spanish MINECO and FEDER (MAT2016-77290-R), the Aragón Government (T05) and the ESF is gratefully acknowledged. J. S-L. thanks Spanish Education Ministry Program FPU2014 his PhD grant. Part of the microscopy work was done in the Laboratorio de Microscopías Avanzadas at the Instituto de Nanociencia de Aragón (LMA-INA)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Sequential amine functionalization inducing structural transition in an aldehyde-containing zeolitic imidazolate framework: application to gas separation membranes

  • Cacho-Bailo, Fernando
  • Etxeberria-Benavides, Miren
  • Karvan, Oğuz
  • Téllez, Carlos
  • Coronas, Joaquín
A modification in the gas separation performance of zeolitic imidazolate framework (ZIF)-supported hollow fiber (HF) membranes by means of an imine-condensation functionalization reaction carried out by microfluidics is reported. The accommodation of voluminous amine molecules in the SIM-1, Zn(4-methyl-5-imidazolecarboxaldehyde)2, also known as ZIF-94, sod structure during the functionalization reaction caused the ZIF atoms to be rearranged in a less dense rho structure, with a wider pore diameter and a diminished CO2 affinity. These changes had effects on the membrane performance, resulting in an enhanced CO2 permeance while maintaining a good permeance–selectivity balance. ZIF aldehyde-containing SIM-1 membranes were earlier prepared on the inner side of polymeric P84® HF using a microfluidic approach. The SIM-1 membranes displayed very interesting results in the separation of gas mixtures of great relevance to the natural gas field. High selectivities in the separation of He/CH4 (160), H2/CH4 (136) and CO2/CH4 (38) mixtures were achieved, and these are the first SIM-1 membranes with such a high separation performance to the best of our knowledge. These SIM-1 membranes were in situ stepwise functionalized with long-chain amine solutions, namely, hexyl- and nonylamine. Microfluidics allowed the easy sequential implementation of this post-reaction step in the membrane fabrication procedure. An imine-condensation reaction took place between the aldehyde groups in the 4-methyl-5-imidazolecarboxaldehyde ligand forming SIM-1 and the corresponding amines. The extent of the reaction was analyzed by FTIR, TGA and XRD, together with the changes in the textural properties and the adsorption capacities., Financial support (MAT2013-40556-R, MAT2016-77290-R) from the Spanish MINECO, the Aragón Government (DGA, T05), the European Social Fund and FEDER is gratefully acknowledged. We also acknowledge the use of the Servicio General de Apoyo a la Investigación-SAI (Universidad de Zaragoza). F. C.-B. acknowledges his DGA predoctoral fellowship. All the microscopy work was done at the Laboratorio de Microscopías Avanzadas at the Instituto de Nanociencia de Aragón (LMA-INA)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Simultaneous use of MOFs MIL-101(Cr) and ZIF-11 in thin film nanocomposite membranes for organic solvent nanofiltration

  • Echaide‐Górriz, Carlos
  • Navarro, Marta
  • Téllez, Carlos
  • Coronas, Joaquín
The MOFs Cr carboxylate MIL-101(Cr) and Zn imidazolate ZIF-11 have different chemical and textural properties. These properties have been combined to prepare thin film nanocomposite (TFN) membranes for organic solvent nanofiltration (OSN) with the two MOFs simultaneously embedded in the same membrane. The TFN membrane containing only ZIF-11 permeated faster than that with only MIL-101(Cr) when filtering sunset yellow (SY) (4.9 L m-2 h-1 bar-1) and acridine orange (AO) (3.2 L m-2 h-1 bar-1), although MIL-101(Cr) alone gave rise in both cases to better rejections (above 90%). The combination of the two MOFs led to a versatile TFN membrane that showed an intermediate performance that improved the rejections given by the TFN membrane synthesized with ZIF-11 and the permeances corresponding to the TFN membrane synthesized with MIL-101(Cr). The effect of the temperature on the TFN membranes designed for this work has also been studied, obtaining apparent activation energies of 13.2 ± 2.1 and 8.3 ± 1.1 kJ mol-1 for the OSN of pure methanol and SY-methanol, respectively., Financial support (MAT2013-40556-R, MAT2016-77290-R) from the Spanish MINECO, the Aragón Government (DGA, T05), the European Social Fund and FEDER is gratefully acknowledged. We also acknowledge the use of the Servicio General de Apoyo a la Investigación-SAI (Universidad de Zaragoza). All the microscopy work was done in the Laboratorio de Microscopías Avanzadas at the Instituto de Nanociencia de Aragón (LMAINA). The authors acknowledge the LMA-INA for offering access to their instruments and expertise., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Structural contraction of zeolitic imidazolate frameworks: Membrane application on porous metallic hollow fibers for gas separation

  • Cacho-Bailo, Fernando
  • Etxeberria-Benavides, Miren
  • David, Oana
  • Téllez, Carlos
  • Coronas, Joaquín
Positive thermal expansion coefficients (TECs) of 52 × 10–6 and 35 × 10–6 K–1 were experimentally calculated in the −116 to 250 °C range for the III-phases of zeolitic imidazolate frameworks (ZIF) ZIF-9(Co) and ZIF-7(Zn), respectively, by means of the unit cell dimensions and volume of the materials in the monoclinic crystal system calculated from the XRD patterns. The unit cell dimensions and volume showed a significant expansion phenomenon as the temperature increased, by as much as 5.5% for ZIF-9-III in the studied range. To exploit the advantages of such thermal behavior, a new approach to the fabrication of ZIF-9-III membranes on thin, flexible, and highly porous nickel hollow fiber (Ni HF) supports by a versatile and easy-controllable microfluidic setup is herein reported. These Ni HF supports result from the sintering of 25-μm Ni particles and display very positive mechanical properties and bending resistance. As compared to the traditional polymer-based HF membranes, the ZIF metal-supported membrane exhibited good durability and robustness throughout its operation in a wide temperature range and after heating and cooling cycles. These benefits derive from (1) the pore-plugging membrane configuration resulting from the high porosity of the support and (2) the similarity between the TECs of the ZIF and the metallic support, both positive, which enhances their mutual compatibility. An increase in the H2/CO2 separation selectivity at low temperatures (as high as 22.2 at −10 °C, along with 102 GPU permeance of H2) was achieved, in agreement with the structural variations observed in the ZIF material., Financial support (Grants MAT2013-40556-R, MAT2016-77290-R) from the Spanish MINECO and FEDER, the Aragón Government (DGA, Grant T05) ,and the European Social Fund is gratefully acknowledged. F.C.-B. acknowledges his DGA predoctoral fellowship. We also acknowledge the use of the Servicio General de Apoyo a la Investigación-SAI (Universidad de Zaragoza)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Synthesis of ZIF-93/11 hybrid nanoparticles via post-synthetic modification of ZIF-93 and their use for H2/CO2 separation

  • Sánchez-Laínez, Javier
  • Zornoza, Beatriz
  • Dawson, Daniel M.
  • Wright, Paul A.
  • Téllez, Carlos
  • Coronas, Joaquín
Joaquín Coronas et al., The present work shows the synthesis of nano-sized hybrid zeolitic imidazolate frameworks (ZIFs) with the rho topology based on a mixture of the linkers benzimidazole (bIm) and 4-methyl-5-imidazolecarboxaldehyde (4-m-5-ica). The hybrid ZIF was obtained by post-synthetic modification of ZIF-93 in a bIm solution. The use of different solvents, MeOH and N,N-dimethylacetamide (DMAc), and reaction times led to differences in the quantity of bIm incorporated to the framework, from 7.4 to 23 % according to solution-state NMR spectroscopy. XPS analysis showed that the mixture of linkers was also present at the surface of the particles. The inclusion of bIm to the ZIF-93 nanoparticles improved the thermal stability of the framework and also increased the hydrophobicity according to water adsorption results. N2 and CO2 adsorption experiments revealed that the hybrid material has an intermediate adsorption capacity, between those of ZIF-93 and ZIF-11. Finally, ZIF-93/11 hybrid materials were applied as fillers in polybenzimidazole (PBI) mixed matrix membranes (MMMs). These MMMs were used for H2 /CO2 separation (at 180 °C) reaching values of 207 Barrer of H2 and a H2 /CO2 selectivity of 7.7 that clearly surpassed the Robeson upper bound (corrected for this temperature)., The research leading to these results has received funding from the European Union Seventh Framework Programme (FP7/2007–2013) under grant agreement no. 608490, project M4CO2. In addition, financial support from the Spanish MINECO and FEDER (MAT2016-77290-R), the Aragón Government (T05) and the ESF is gratefully acknowledged. J.S.L. thanks the Spanish Education Ministry Program FPU2014 for his PhD grant. All the microscopy work was done in the Laboratorio de Microscopías Avanzadas at the Instituto de Nanociencia de Aragón (LMA-INA). The authors would like to acknowledge the use of the Servicio General de Apoyo a la Investigación-SAI, Universidad de Zaragoza., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Thin-film nanocomposite membrane with the minimum amount of MOF by the Langmuir-Schaefer technique for nanofiltration

  • Navarro, Marta
  • Benito, Javier
  • Paseta, Lorena
  • Gascón, Ignacio
  • Coronas, Joaquín
  • Téllez, Carlos
An innovative procedure for positioning a monolayer of hydrophilic metal organic framework (MOF) MIL-101(Cr) (MIL, Materials of Institute Lavoisier) nanoparticles (NPs) in thin-film nanocomposite (TFN) membranes has been implemented by transferring a Langmuir-Schaefer (LS) film of the MOF in between the polyamide thin layer at the top and the cross-linked asymmetric polyimide (P84) support at the bottom. The presence and layout of the LS-MIL-101(Cr) monolayer in the TFN membrane was confirmed by scanning transmission electron microscopy imaging with a high-angle annular dark-field detector images and X-ray photoelectron spectroscopy, energy-dispersive X-ray spectroscopy, electron energy loss spectroscopy, and atomic force microscopy analyses. This methodology requires the smallest amount of MOF reported to date, 3.8 μg cm-2, and promotes the formation of a defect-free ultrathin MOF film. Although conventional TFN membranes tend to show MOF agglomerates that could contribute to the formation of unselective defects, LS-TFN membranes, characterized by a homogeneous and continuous MOF coating, exhibit an optimal membrane performance, without a significant decrease in selectivity. Outstanding methanol permeances, one of the best results reported to date, of 10.1 ± 0.5 L m-2 h-1 bar-1 when filtering sunset yellow and of 9.5 ± 2.1 L m-2 h-1 bar-1 when filtering rose bengal have been achieved in LS-TFN membranes with a rejection higher than 90% in all cases. Methanol permeates through the polyamide and the LS-MIL-101(Cr) monolayer, greatly enhanced by the MOF pore system, in comparison to thin-film composite and conventional TFN membranes (7.5 ± 0.7 and 7.7 ± 1.1 L m-2 h-1 bar-1 when filtering sunset yellow), respectively, in which polyamide areas free of MOF NPs are present., Financial support from the Spanish Ministry of Economy and Competitiveness (MINECO) and FEDER (MAT2016-77290-R), the European Social Fund (ESF), and the Aragón Government (DGA, T05) is gratefully acknowledged. L.P. also thanks the MINECO for a Ph.D. grant., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Tuning the separation properties of zeolitic imidazolate framework core-shell structures: Via post-synthetic modification

  • Sánchez-Laínez, Javier
  • Veiga, Adrián
  • Zornoza, Beatriz
  • Balestra, Salvador R. G.
  • Hamad, Said
  • Ruiz-Salvador, A. Rabdel
  • Calero, Sofía
  • Téllez, Carlos
  • Coronas, Joaquín
The conversion of ZIF-8 into ZIF-7 via post-synthetic modification with benzimidazole has been monitored by quantifying the liberated 2-methylimidazole by chromatography. The reaction kinetics have been adjusted to the shrinking core model, providing the diffusion coefficient of bIm inside the pores and the reaction kinetic constant (2.86 × 10−7 cm2 s−1 and 1.36 × 10−4 cm s−1, respectively). A wide variety of ZIF-7/8 hybrid core–shell frameworks have been obtained during this reaction. The most promising have been characterized by SEM/TEM, TGA, N2 and CO2 adsorption, FTIR and 13C NMR, showing features of the coexistence of both phases inside the frameworks. Their structures have also been simulated, providing comparable XRD and adsorption results. The hybrid material has been used as a filler for PBI mixed matrix membranes (MMMs) applied to H2/CO2 separation, enhancing the performances of the bare PBI polymer and MMMs containing ZIF-8 or ZIF-7 as a filler, with a maximum H2 permeability value of 1921 Barrer and a H2/CO2 selectivity of 11.8., The research leading to these results has received funding from the European Union Seventh Framework Programme (FP7/2007–2013) under grant agreement no 608490, project M4CO2. In addition, financial support from the Spanish MINECO and FEDER (MAT2016-77290-R and CTP2016-80206-P), the Aragón Government (T05) and the ESF is gratefully acknowledged. J. S.-L. thanks the Spanish Education Ministry Program FPU2014 for his PhD grant. S. R. G. Balestra also thanks the Spanish MINECO for his predoctoral fellowship (BES-2014-067825 from CTQ2013-48396-P). All the microscopy work was done at the Laboratorio de Microscopías Avanzadas at the Instituto de Nanociencia de Aragón (LMA-INA). Finally, the authors would like to acknowledge the use of the Servicio General de Apoyo a la Investigación-SAI, Universidad de Zaragoza., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Ultrapermeable thin film ZIF-8/polyamide membrane for H2/CO2 separation at high temperature without using sweep gas

  • Sánchez-Laínez, Javier
  • Paseta, Lorena
  • Navarro, Marta
  • Zornoza, Beatriz
  • Téllez, Carlos
  • Coronas, Joaquín
The use of thin film composites containing metal–organic frameworks (MOFs) as filler is of widespread interest for nanofiltration issues, since their thin selective layer allows a high permeation flow. The application of this kind of membranes for gas separation should provide a better permeance in comparison with other polymeric membranes and a reduction in the amount of MOF required for their fabrication. Here, the preparation of 50–100 nm thick polyamide flat membranes containing zeolitic imidazolate framework-8 (ZIF-8) nanoparticles is shown via interfacial polymerization, containing a lower amount of MOF (0.013 g m−2 membrane) as compared to other membranes used for gas separation. The membranes are applied for H2/CO2 separation at high temperatures and pressures, showing a stable performance at 180 °C for at least seven days. Outstanding separation values are 328 GPU of H2 and a H2/CO2 selectivity of 18.1 at 180 °C and 6 bar feed without transmembrane pressure. These membranes, also measurable without sweep gas, are highly suitable for industrial application., The research leading to these results has received funding from the European Union Seventh Framework Programme (FP7/2007-2013) under grant agreement no. 608490, project M4CO2. In addition, financial support from the Spanish MINECO and FEDER (MAT2016-77290-R), the Aragón Government (T05) and the ESF is gratefully acknowledged. J. S.-L. thanks the Spanish Education Ministry Program FPU2014 and L.P. the Ministry of Economy, Industry and Competitiveness Program FPI2014 for their PhD grants., Peer reviewed
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Insight into the reversible structural crystalline-state transformation from MIL-53(Al) to MIL-68(Al)

  • Perea-Cachero, A.
  • Romero, E.
  • Téllez, C.
  • Coronas, J.
The reversible crystalline transformation between MIL-53(Al) and MIL-68(Al) is described. This followed a uniform conversion model with cleavage and formation of metal-ligand bonds after exchange or removal of guest molecules. MIL-68(Al) materials produced during the transformations had higher thermal stability and crystallinity than the as-synthesized MIL-68(Al).
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Sequential amine functionalization inducing structural transition in an aldehyde-containing zeolitic imidazolate framework: Application to gas separation membranes

  • Cacho-Bailo, Fernando
  • Etxeberría-Benavides, Miren
  • Karvan, Oguz
  • Téllez, Carlos
  • Coronas, Joaquín
A modification in the gas separation performance of zeolitic imidazolate framework (ZIF)-supported hollow fiber (HF) membranes by means of an imine-condensation functionalization reaction carried out by microfluidics is reported. The accommodation of voluminous amine molecules in the SIM-1, Zn(4-methyl-5-imidazolecarboxaldehyde)2, also known as ZIF-94, sod structure during the functionalization reaction caused the ZIF atoms to be rearranged in a less dense rho structure, with a wider pore diameter and a diminished CO2 affinity. These changes had effects on the membrane performance, resulting in an enhanced CO2 permeance while maintaining a good permeance-selectivity balance. ZIF aldehyde-containing SIM-1 membranes were earlier prepared on the inner side of polymeric P84® HF using a microfluidic approach. The SIM-1 membranes displayed very interesting results in the separation of gas mixtures of great relevance to the natural gas field. High selectivities in the separation of He/CH4 (160), H2/CH4 (136) and CO2/CH4 (38) mixtures were achieved, and these are the first SIM-1 membranes with such a high separation performance to the best of our knowledge. These SIM-1 membranes were in situ stepwise functionalized with long-chain amine solutions, namely, hexyl- and nonylamine. Microfluidics allowed the easy sequential implementation of this post-reaction step in the membrane fabrication procedure. An imine-condensation reaction took place between the aldehyde groups in the 4-methyl-5-imidazolecarboxaldehyde ligand forming SIM-1 and the corresponding amines. The extent of the reaction was analyzed by FTIR, TGA and XRD, together with the changes in the textural properties and the adsorption capacities.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

A new zeolitic hydroxymethylimidazolate material and its use in mixed matrix membranes based on 6FDA-DAM for gas separation

  • Perea-Cachero, Adelaida
  • Sánchez-Laínez, Javier
  • Berenguer-Murcia, Ángel
  • Cazorla-Amorós, Diego
  • Téllez, Carlos
  • Coronas, Joaquín
The new ZIF named UZAR-S13 is formed by Zn2+ and 4(5)-(hydroxymethyl)imidazolate. UZAR-S13 has two distinct phases according to SEM and XRD: amorphous spheres and sheet crystals. UZAR-S13 and byproducts, with no N2 adsorption, rendered a notable CO2 uptake (up to 3.8 mmol g-1 at 30 bar and 0 °C), approaching values of known ZIFs. The most promising materials were included as fillers in mixed matrix membranes based on copolyimide 6FDA-DAM to study the separation of CO2/CH4, CO2/N2, H2/CO2 and H2/CH4 mixtures. The pore blocking hindered the gas flow of bulky molecules (CH4, N2 and CO2). The high CO2 adsorption on sheet crystals also contributed to the decrease in the permeability of CH4, N2 and CO2, giving poor selectivities. In contrast, the MMMs improved both the H2/CH4 selectivity (8.9–12.7 vs. 7.2) and permeability of H2 (544–597 vs. 505 Barrer) of the bare 6FDA-DAM membrane. This emphasizes the potential application of the fillers in the separation by molecular sieving of gas mixtures without CO2.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Contribución de congreso (ConferenceOutput)

Ultrathin composite polymeric membranes for CO2/N2 separation with minimum thickness and high co2 permeance

  • Benito, Javier
  • Sánchez-Laínez, Javier
  • Zornoza, Beatriz
  • Martín, Santiago
  • Carta, Mariolino
  • Malpass-Evans, Richard
  • Téllez, Carlos
  • McKeown, Neil B.
  • Coronas, Joaquín
  • Gascón, Ignacio
The use of ultrathin films as selective layers in composite membranes offers significant advantages in gas separation for increasing productivity while reducing the membrane size and energy costs. In this contribution, composite membranes have been obtained by the successive deposition of approximately 1 nm thick monolayers of a polymer of intrinsic microporosity (PIM) on top of dense membranes of the ultra-permeable poly[1-(trimethylsilyl)-1-propyne] (PTMSP). The ultrathin PIM films (30 nm in thickness) demonstrate CO2 permeance up to seven times higher than dense PIM membranes using only 0.04¿% of the mass of PIM without a significant decrease in CO2/N2 selectivity.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Tuning the separation properties of zeolitic imidazolate framework core-shell structures via post-synthetic modification

  • Sánchez-Laínez, J.
  • Veiga, A.
  • Zornoza, B.
  • Balestra, S.R.G.
  • Hamad, S.
  • Ruiz-Salvador, A.R.
  • Calero, S.
  • Téllez, C.
  • Coronas, J.
The conversion of ZIF-8 into ZIF-7 via post-synthetic modification with benzimidazole has been monitored by quantifying the liberated 2-methylimidazole by chromatography. The reaction kinetics have been adjusted to the shrinking core model, providing the diffusion coefficient of bIm inside the pores and the reaction kinetic constant (2.86 × 10-7 cm2 s-1 and 1.36 × 10-4 cm s-1, respectively). A wide variety of ZIF-7/8 hybrid core-shell frameworks have been obtained during this reaction. The most promising have been characterized by SEM/TEM, TGA, N2 and CO2 adsorption, FTIR and 13C NMR, showing features of the coexistence of both phases inside the frameworks. Their structures have also been simulated, providing comparable XRD and adsorption results. The hybrid material has been used as a filler for PBI mixed matrix membranes (MMMs) applied to H2/CO2 separation, enhancing the performances of the bare PBI polymer and MMMs containing ZIF-8 or ZIF-7 as a filler, with a maximum H2 permeability value of 1921 Barrer and a H2/CO2 selectivity of 11.8.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Ultrapermeable Thin Film ZIF-8/Polyamide Membrane for H-2/CO2 Separation at High Temperature without Using Sweep Gas

  • Sanchez-Lainez, J.
  • Paseta, L.
  • Navarro, M.
  • Zornoza, B.
  • Tellez, C.
  • Coronas, J.
The use of thin film composites containing metal-organic frameworks (MOFs) as filler is of widespread interest for nanofiltration issues, since their thin selective layer allows a high permeation flow. The application of this kind of membranes for gas separation should provide a better permeance in comparison with other polymeric membranes and a reduction in the amount of MOF required for their fabrication. Here, the preparation of 50-100 nm thick polyamide flat membranes containing zeolitic imidazolate framework-8 (ZIF-8) nanoparticles is shown via interfacial polymerization, containing a lower amount of MOF (0.013 g m(-2) membrane) as compared to other membranes used for gas separation. The membranes are applied for H-2/CO2 separation at high temperatures and pressures, showing a stable performance at 180 degrees C for at least seven days. Outstanding separation values are 328 GPU of H-2 and a H-2/CO2 selectivity of 18.1 at 180 degrees C and 6 bar feed without transmembrane pressure. These membranes, also measurable without sweep gas, are highly suitable for industrial application.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Controlled deposition of MOFs by dip-coating in thin film nanocomposite membranes for organic solvent nanofiltration

  • Sarango, Lilian
  • Paseta, Lorena
  • Navarro, Marta
  • Zornoza, Beatriz
  • Coronas, Joaquín
ZIF-8 and ZIF-67 particles, with sizes of 70 ± 10 nm and 240 ± 40 nm, respectively, were deposited by dip-coating on top of polyimide P84® asymmetric supports. In the best conditions, this gives rise to a MOF (metal-organic framework) monolayer which remains on the polyimide support during the interfacial polymerization of polyamide carried out to produce a thin film nanocomposite membrane for organic solvent nanofiltration (OSN). This method is simple, shorter and is environmentally friendly, since no excess MOF is lost during the interfacial polymerization, exhibiting good OSN results: dye rejection of 90% together with a high methanol permeance of 8.7 L m-2 h-1 bar-1.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Enhancement of CO2/CH4 separation performances of 6FDA-based co-polyimides mixed matrix membranes embedded with UiO-66 nanoparticles

  • Zamidi Ahmad, M.
  • Navarro, M.
  • Lhotka, M.
  • Zornoza, B.
  • Téllez, C.
  • Fila, V.
  • Coronas, J.
Metal-organic frameworks (MOFs) incorporation into mixed matrix membranes (MMMs) is gaining more attention due to the combined advantages of high separation performance and easy processability. Nanoparticles (NPs) of CO2-philic MOF UiO-66 (Zr-BDC) were synthesized with high surface area and ca. 50 nm particle size (and also for comparison with 100 and 200 nm sizes). They were incorporated into three 6FDA-based co-polyimides (namely 6FDA-BisP, 6FDA-ODA, and 6FDA-DAM), forming MMMs with loadings in the 4–23 wt% range. The NPs and MMMs were characterized accordingly by XRD, BET, SEM, TEM, FTIR, and TGA. CO2 and CH4 isotherms on the NPs were measured by a static volumetric method at the pressure up to 10 bar. Fractional free volume (FFV) was calculated using solid density, measured by pycnometer. Gas separation performance was evaluated using a feed composition of 50%:50% CO2:CH4 binary mixture at 35 °C and a pressure difference of 2 bar. The presence of UiO-66 NPs in the continuous 6FDA-BisP and 6FDA-ODA co-polyimides improved both CO2 permeability and CO2/CH4 selectivity by 50–180% and 70–220%, respectively. In the case of 6FDA-DAM MMMs, the CO2 permeability was significantly improved by 92%, while maintaining the CO2/CH4 selectivity. The best results in terms of CO2/CH4 selectivity were 41.9 for 6FDA-BisP (17 wt% filler loading, 108 Barrer of CO2), 57.0 for 6FDA-ODA (7 wt% filler loading, 43.3 Barrer of CO2) and 32.0 for 6FDA-DAM (8 wt% filler loading, 1728 Barrer of CO2).
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Reseña (Review)

New strategies based on microfluidics for the synthesis of metal-organic frameworks and their membranes

  • Echaide-Górriz, C.
  • Clément, C.
  • Cacho-Bailo, F.
  • Téllez, C.
  • Coronas, J.
Metal-organic frameworks (MOFs) are highly porous crystalline materials formed by the coordination of organic ligands with metal clusters. Despite the significant progress in their development over the last few years and their applications in various classic and emerging fields, the control of their shape and size remains a challenge, in particular the search for more efficient and environmentally friendly syntheses. In this context, the microfluidics approach allows not only the continuous production of MOFs but also an accurate reaction parameter control in their synthesis, representing a step towards intensification, versatility and scalability in the use of MOFs. Microfluidics also offers the possibility of synthesizing effective and defect free MOF-based hollow fiber membranes saving reactants as compared to conventional methods. This review is devoted to highlighting the multitude of synergies appearing when dealing with MOFs and microfluidics, not only in the bare synthesis of MOFs and their hierarchical structures but also when fabricating hollow fiber membranes with important applications in the separation field.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Synthesis of ZIF-93/11 Hybrid Nanoparticles via Post-Synthetic Modification of ZIF-93 and Their Use for H2/CO2 Separation

  • Sánchez-Laínez, J.
  • Zornoza, B.
  • Orsi, A.F.
  • Lozinska, M.M.
  • Dawson, D.M.
  • Ashbrook, S.E.
  • Francis, S.M.
  • Wright, P.A.
  • Benoit, V.
  • Llewellyn, P.L.
  • Téllez, C.
  • Coronas, J.
The present work shows the synthesis of nano-sized hybrid zeolitic imidazolate frameworks (ZIFs) with the rho topology based on a mixture of the linkers benzimidazole (bIm) and 4-methyl-5-imidazolecarboxaldehyde (4-m-5-ica). The hybrid ZIF was obtained by post-synthetic modification of ZIF-93 in a bIm solution. The use of different solvents, MeOH and N, N-dimethylacetamide (DMAc), and reaction times led to differences in the quantity of bIm incorporated to the framework, from 7.4 to 23 % according to solution-state NMR spectroscopy. XPS analysis showed that the mixture of linkers was also present at the surface of the particles. The inclusion of bIm to the ZIF-93 nanoparticles improved the thermal stability of the framework and also increased the hydrophobicity according to water adsorption results. N2 and CO2 adsorption experiments revealed that the hybrid material has an intermediate adsorption capacity, between those of ZIF-93 and ZIF-11. Finally, ZIF-93/11 hybrid materials were applied as fillers in polybenzimidazole (PBI) mixed matrix membranes (MMMs). These MMMs were used for H2/CO2 separation (at 180 °C) reaching values of 207 Barrer of H2 and a H2/CO2 selectivity of 7.7 that clearly surpassed the Robeson upper bound (corrected for this temperature).
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Homogeneous thin coatings of zeolitic imidazolate frameworks prepared on quartz crystal sensors for CO2 adsorption

  • Sarango, Lilian
  • Benito, Javier
  • Gascón, Ignacio
  • Zornoza, Beatriz
  • Coronas, Joaquín
Thin films of four zeolitic-imidazolate frameworks (ZIF-8, ZIF-67, ZIF-7, and ZIF-93) have been fabricated by a dip-coating method on glass and quartz crystal microbalance (QCM) substrates. Homogeneous coatings with sizes of crystals of 65 ± 20, 285 ± 96, 61 ± 20 and 72 ± 21 nm for ZIF-8, ZIF-67, ZIF-7, and ZIF-93, respectively, were obtained. Upon characterization of the ZIFs and coatings by XRD, TGA, SEM, FTIR, contact angle measurement and N2 adsorption, the coatings were exposed to vapors of dichloromethane for activation. The CO2 adsorption of the coatings was then studied using a QCM device.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

The fabrication of ultrathin films and their gas separation performance from polymers of intrinsic microporosity with two-dimensional (2D) and three-dimensional (3D) chain conformations

  • Benito, J.
  • Vidal, J.
  • Sánchez-Laínez, J.
  • Zornoza, B.
  • Téllez, C.
  • Martín, S.
  • Msayib, K.J.
  • Comesaña-Gándara, B.
  • McKeown, N.B.
  • Coronas, J.
  • Gascón, I.
The expansion of the use of polymeric membranes in gas separation requires the development of membranes based on new polymers with improved properties and their assessment under real operating conditions. In particular, the fabrication of ultrathin films of high performance polymers that can be used as the selective layer in composite membranes will allow large reductions in the amount of the expensive polymer used and, hence, the cost of membrane fabrication. In this contribution, two polymers of intrinsic microporosity (PIMs) with very different chain configurations (two-dimensional, 2D, chains or conventional contorted three-dimensional, 3D, conformation) have been compared in their ability to form ultrathin films, showing the relevance of polymer design to obtain compact and defect-free films. Monolayers of the 2D polymer PIM-TMN-Trip can be efficiently deposited onto poly[1-(trimethylsilyl)-1-propyne] (PTMSP) to obtain composite membranes with a CO2/N2 selectivity similar to that of the corresponding thick membranes of the same PIM using only a small fraction of the selective polymer (less than 0.1%).
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Nanosheets of MIL-53(Al) applied in membranes with improved CO 2 /N 2 and CO 2 /CH 4 selectivities

  • Perea-Cachero, A.
  • Sánchez-Laínez, J.
  • Zornoza, B.
  • Romero-Pascual, E.
  • Téllez, C.
  • Coronas, J.
MIL-68(Al) and MIL-53(Al) are carboxylate-based metal-organic frameworks (MOFs) with the same chemical composition but different structures (polymorphs). In this study, MIL-53(Al) nanosheets of ca. 150 nm in size with an average thickness of 3.5 ± 0.9 nm were obtained after immersion of a sample composed of MIL-68(Al) and MIL-53(Al) in water under different conditions (ultrasound, stirring, reflux, 60 °C and room temperature). The disaggregated MIL-53(Al) nanosheets produced under more severe conditions were suspended in a PDMS solution and then deposited on asymmetric polyimide P84® supports under vacuum filtration to form supported mixed matrix membranes (MMMs). When applied to the separation of CO 2 /CH 4 and CO 2 /N 2 mixtures, the MMM with MIL-53(Al) nanosheets improved the CO 2 /CH 4 (28.4-28.7 vs. 22.4) and CO 2 /N 2 (19.9-23.2 vs. 17.5) selectivities of the conventional MIL-53(Al) MMM with higher CO 2 permeances (20.8-29.6 GPU vs. 9.5 GPU for CO 2 /CH 4 and 17.7-26.8 GPU vs. 11.2 GPU for CO 2 /N 2 ).
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Hydrogen Separation at High Temperature with Dense and Asymmetric Membranes Based on PIM-EA(H2)-TB/PBI Blends

  • Sánchez-Laínez, J.
  • Zornoza, B.
  • Carta, M.
  • Malpass-Evans, R.
  • McKeown, N.B.
  • Téllez, C.
  • Coronas, J.
The preparation of dense and asymmetric flat membranes from the blending of polybenzimidazole (PBI) and (1.5-20 wt %) of a polymer of intrinsic microporosity (PIM-EA(H2)-TB) is reported. Thermal characterization validated the blend by revealing a single glass transition temperature, which suggests the absence of polymer phase segregation. In addition, the decomposition activation energy and d-spacing of the blends follow trends that correlate with the amount of PIM component. The membranes have been tested for the separation of H2/CO2 mixtures. The properties of the dense membranes, which also incorporate zeolitic imidazolate-8 (ZIF-8) nanoparticles, helped understanding of the behavior of the PIM/PBI blends by which phase inversion results in high separation performance asymmetric membranes. Asymmetric membranes show H2/CO2 selectivities of 23.8 (10/90 wt % PIM/PBI) and 19.4 (20/80 wt % PIM/PBI) together with respective H2 permeances of 57.9 and 83.5 GPU at 250 °C and 6 bar feed pressure. The gas separation performance of these asymmetric blends has been fitted to an empirical model, showing the influence of the amount of PIM and the feed pressure.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Thin supported MOF based mixed matrix membranes of Pebax® 1657 for biogas upgrade

  • Sánchez-Laínez, J.
  • Gracia-Guillén, I.
  • Zornoza, B.
  • Téllez, C.
  • Coronas, J.
This work shows the preparation of thin mixed matrix membranes (MMMs) with a 2-3 µm thick Pebax® 1657 layer on two different supports: a porous asymmetric polyimide P84® and dense polytrimethylsilylpropyne (PTMSP). Nanoparticles of metal-organic frameworks (MOFs) ZIF-8, MIL-101(Cr), UiO-66 and ZIF-7/8 core-shells were selected as fillers for the Pebax® 1657 based MMMs, all of them being MOFs with high CO2 adsorption capacity but different pore size distribution. All the membranes were characterized by SEM, FTIR, Raman, TGA and XRD analyses, showing in all cases a perfect compatibility of the Pebax® layer with both supports and also a good dispersion of the fillers in the polymeric matrix. These membranes were applied for the separation of equimolar CO2/CH4 mixtures at 35 °C under feed pressures between 3 and 5 bar, where an improvement in the gas separation performance with increasing pressure was noticed, thanks to the favored solubility of CO2. The synergistic compatibility between Pebax® 1657 and P84® gave rise to a 470% enhancement in CO2/CH4 selectivity, reaching a maximum value of 114 while the CO2 permeance increased by 40% up to 7.5 GPU. The addition of fillers in the Pebax® polymeric phase produced an improvement in the gas separation performance of the membranes, especially in terms of permeance, where the MMMs containing a 10 wt% loading of UiO-66 reached the optimum value of 11.5 GPU of CO2 (together with a CO2/CH4 selectivity of 55.6).
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Poly(ether-block-amide) copolymer membrane for CO2/N-2 separation: the influence of the casting solution concentration on its morphology, thermal properties and gas separation performance

  • Martinez-Izquierdo, Lidia
  • Malankowska, Magdalena
  • Sanchez-Lainez, Javier
  • Tellez, Carlos
  • Coronas, Joaquín
The present work is focused on the study of the effect that the casting solution concentration has on the morphology and gas separation performance of poly(ether-block-amide) copolymer membranes (Pebax (R) MH 1657). With this aim, three different concentrations of Pebax (R) MH 1657 in the casting solution (1, 3 and 5 wt%) were used to prepare dense membranes with a thickness of 40 mu m. The morphology and thermal stability of all membranes were characterized by scanning electron microscopy, X-ray diffraction, differential scanning calorimetry, rotational viscometry and thermogravimetric analyses. An increase in crystallinity was notable when the amount of solvent in the Pebax (R) MH 1657 solution was higher, mainly related to the polymer chains arrangement and the solvent evaporation time. Such characteristic seemed to play a key role in the thermal degradation of the membranes, confirming that the most crystalline materials tend to be thermally more stable than those with lower crystallinity. To study the influence of their morphology and operating temperature on the CO2 separation, gas separation tests were conducted with the gas mixture CO2/N-2. Results indicated that a compromise must be found between the amount of solvent used to prepare the membranes and the crystallinity, in order to reach the best gas separation performance. In this study, the best performance was achieved with the membrane prepared from a 3 wt% casting solution, reaching at 35 degrees C and under a feed pressure of 3 bar, a CO2 permeability of 110 Barrer and a CO2/N-2 selectivity of 36.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Synthesis and Characterization of Covalent Triazine Framework CTF-1@Polysulfone Mixed Matrix Membranes and Their Gas Separation Studies

  • Dey, Subarna
  • Bügel, Stefanie
  • Sorribas, Sara
  • Nuhnen, Alexander
  • Bhunia, Asamanjoy
  • Coronas, Joaquín
  • Janiak, Christoph
Covalent triazine framework CTF-1 and polysulfone (PSF) are used to form mixed-matrix membranes (MMMs) with 8, 16, and 24 wt% of the porous filler material CTF-1. Studies on permeability and selectivity are carried out concerning the gases O2, N2, CO2, and CH4. CO2 permeability of the synthesized MMMs increases by 5.4 Barrer in comparison to the pure PSF membrane. The selectivity remains unchanged for O2/N2 and CO2/CH4 but was found to be increased for CO2/N2. Further, comparisons to theoretical models for permeability prediction yield a permeability for CTF-1 which is about six times higher than the permeability of PSF. The inverse of the sum of the free fractional volumes (FFV) of the polymer and the filler correlate linearly to the logarithm of the permeabilities of the gases which conversely indicates that the porosity of the filler contributes to the gas transport through the membrane.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Simultaneous use of MOFs MIL-101(Cr) and ZIF-11 in thin film nanocomposite membranes for organic solvent nanofiltration

  • Echaide-Górriz, Carlos
  • Navarro, Marta
  • Téllez, Carlos
  • Coronas, Joaquín
The MOFs Cr carboxylate MIL-101(Cr) and Zn imidazolate ZIF-11 have different chemical and textural properties. These properties have been combined to prepare thin film nanocomposite (TFN) membranes for organic solvent nanofiltration (OSN) with the two MOFs simultaneously embedded in the same membrane. The TFN membrane containing only ZIF-11 permeated faster than that with only MIL-101(Cr) when filtering sunset yellow (SY) (4.9 L m-2 h-1 bar-1) and acridine orange (AO) (3.2 L m-2 h-1 bar-1), although MIL-101(Cr) alone gave rise in both cases to better rejections (above 90%). The combination of the two MOFs led to a versatile TFN membrane that showed an intermediate performance that improved the rejections given by the TFN membrane synthesized with ZIF-11 and the permeances corresponding to the TFN membrane synthesized with MIL-101(Cr). The effect of the temperature on the TFN membranes designed for this work has also been studied, obtaining apparent activation energies of 13.2 ± 2.1 and 8.3 ± 1.1 kJ mol-1 for the OSN of pure methanol and SY-methanol, respectively.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

110th Anniversary: Polyamide/Metal-Organic Framework Bilayered Thin Film Composite Membranes for the Removal of Pharmaceutical Compounds from Water

  • Paseta, L.
  • Antorán, D.
  • Coronas, J.
  • Téllez, C.
Nanofiltration can be a useful tool to remove pharmaceuticals in water sources. The performance of the most used thin film composite (TFC) membranes, typically with a thin polyamide (PA) layer, can be improved using thin film nanocomposite (TFN) membranes obtained by the introduction of a filler within the PA layer. In this work, to control the positioning of the filler two kinds of PA/metal-organic framework (MOF) bilayered TFC (BTFC) membranes, PA/ZIF-93 and PA/HKUST-1, were synthesized onto polyimide supports. First, the interfacial synthesis was used for the preparation of a MOF layer, and second, a PA layer was synthesized by interfacial polymerization. These BTFC membranes were applied in the nanofiltration of diclofenac and naproxen aqueous solutions obtaining a maximum water permeance of 33.1 and 24.9 L·m -2 ·h -1 ·bar -1 , respectively, with a rejection of =98% when HKUST-1 was used. These permeance improvements (using diclofenac, 4.9 and 3.4 times the value of the TFC and TFN membranes, respectively) are related to the PA layer thickness, MOF porosity, membrane hydrophilicity, and membrane roughness.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Towards the dehydration of ethanol using pervaporation cross-linked poly (vinyl alcohol)/graphene oxide membranes

  • Castro-Muñoz, Roberto
  • Buera-Gonzalez, Juan
  • Iglesia, Óscar de la
  • Galiano, Francesco
  • Fila, Vlastimil
  • Malankowska, Magdalena
  • Rubio, César
  • Figoli, Alberto
  • Tellez, Carlos
  • Coronas, Joaquín
Highly hydrophilic inorganic material graphene oxide (GO) was successfully prepared and incorporated into a cross-linked poly(vinyl alcohol) (PVA) matrix. The obtained mixed matrix membranes (MMMs) have been used for the dehydration of ethanol (10: 90% water-ethanol) by pervaporation (PV), monitoring their performance in terms of total permeate flux, partial components fluxes, as well as their separation factor. The effect of filler was analyzed by doubling the GO content (at 0.5, 1.0, and 2.0 wt%) in the MMMs. A complete analysis of the operating temperature (between 40 and 70 degrees C) was carried out by means of Arrhenius relationship. Moreover, the membranes were characterized by field emission scanning electron microscopy (FESEM), transmission electron microscopy (TEM), differential scanning calorimetry (DSC), thermo-gravimetric analysis (TGA), X-ray diffraction (XRD), Fourier transformed infrared spectroscopy (FTIR), measurements of degree of swelling (uptake), water contact angle (CA) and mechanical properties. At 40 degrees C, the best performance was provided by the MMMs containing 1 wt% GO, showing a separation factor of 263 and a permeate flux of about 0.137 kg m(-2) h(-1) (in which 0.133 kg m(-2) h(-1) corresponds to water). This represents a 75% enhancement of the original permeation rate of pristine cross-linked PVA membranes. Taking into account the promising results, it is likely that these MMMs will provide featured benefits in green processes, e.g. ethanol purification by means of less-energy consumption.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Mathematical modeling of temperature and pressure effects on permeability, diffusivity and solubility in polymeric and mixed matrix membranes

  • Maghami, S.
  • Mehrabani-Zeinabad, A.
  • Sadeghi, M.
  • Sánchez-Laínez, J.
  • Zornoza, B.
  • Téllez, C.
  • Coronas, J.
Due to the temperature and pressure dependency of gas transport through polymeric and mixed matrix membranes, probing of their separation performance at different operational conditions seems crucial to determine an optimal operational condition. To minimize the number of costly and time consuming experiments, a modified form of van''t Hoff-Arrhenius model was developed to consider the simultaneous effects of temperature and pressure on the separation performance of polymeric and mixed matrix membranes. Moreover, the proposed model is capable to consider pressure dependency of energetic parameters of Arrhenius model including activation energies of permeability and diffusivity, heat of sorption and the corresponding pre-exponential factors. The validity of the proposed model was investigated by using permeation coefficients of CO 2 and N 2 in a binary mixture through 6FDA-DAM at different temperatures in the range of 35–55 °C and in the feed pressure range from 2 to 5 atm. Besides, from data taken from the literature, the proposed model was validated by the prediction of temperature and pressure dependency of transport properties of glassy and rubbery polymers as well as mixed matrix membranes (MMMs) for different gas molecules including He, H 2 , CO 2 , O 2 , N 2 , CH 4 and C 4 H 10 . Predictions corresponding to 300 data points revealed that the maximum average absolute relative error was 5.1%.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Reseña (Review)

Ultrathin permselective membranes: The latent way for efficient gas separation

  • Castro-Muñoz, Roberto
  • Agrawal, Kumar V.
  • Coronas, Joaquín
Membrane gas separation has attracted the attention of chemical engineers for the selective separation of gases. Among the different types of membranes used, ultrathin membranes are recognized to break the trade-off between selectivity and permeance to provide ultimate separation. Such success has been associated with the ultrathin nature of the selective layer as well as their defect-free structure. These membrane features can be obtained from specific membrane preparation procedures used, in which the intrinsic properties of different nanostructured materials (e.g., polymers, zeolites, covalent-organic frameworks, metal-organic frameworks, and graphene and its derivatives) also play a crucial role. It is likely that such a concept of membranes will be explored in the coming years. Therefore, the goal of this review study is to give the latest insights into the use of ultrathin selective barriers, highlighting and describing the primary membrane preparation protocols applied, such as atomic layer deposition, in situ crystal formation, interfacial polymerization, Langmuir-Blodgett technique, facile filtration process, and gutter layer formation, to mention just a few. For this, the most recent approaches are addressed, with particular emphasis on the most relevant results in separating gas molecules. A brief overview of the fundamentals for the application of the techniques is given. Finally, by reviewing the ongoing development works, the concluding remarks and future trends are also provided.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Contribución de congreso (ConferenceOutput)

The Effect of Hydrogen Peroxide on the synthesis of Terephthalate-Based metal-organic frameworks

  • Monteagudo-Olivan, Rebeca
  • Jiménez-Fernández, Isabel
  • López-Ram-de-Viu, Pilar
  • Sebastian, Víctor
  • Coronas, Joaquín
Metal-organic frameworks (MOFs) are versatile materials for applications in fields including the environment, energy and health. A synthetic route for improving the formation of MOFs has been developed and is triggered by hydrogen peroxide (H2O2) to promote the formation of terephthalate-based MOFs of MIL-53 and MIL-68 types, specifically those made from Fe3+ and Al3+ and mixtures of both. Different characterization techniques (TGA, XRD, SEM, TEM, N2 porosimetry and Raman, mass and NMR spectroscopies) gave insights into the effect of H2O2 on the MOF synthesis. The reaction yield was significantly improved (the highest yield being 74 % for MIL-53(Al)), while crystallinity and N2 adsorption properties were mostly maintained for phases based on Al and Al/Fe. Furthermore, a reaction mechanism was envisaged from the mass spectroscopic analysis of the reaction solutions, thus suggesting that H2O2 plays the role of a µ-hydroxo bridge promoter, favoring the link between terephthalate ligands and aluminum-containing species to give rise to the µ-carboxylate bridges, leading to a faster growth of the final MOF, and offering a novel MOF synthesis approach.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Ultrathin Films of Porous Metal–Organic Polyhedra for Gas Separation

  • Andrés, Miguel A.
  • Carné-Sánchez, Arnau
  • Sánchez-Laínez, Javier
  • Roubeau, Olivier
  • Coronas, Joaquín
  • Maspoch, Daniel
  • Gascón, Ignacio
Ultrathin films of a robust RhII-based porous metal–organic polyhedra (MOP) have been obtained. Homogeneous and compact monolayer films (ca. 2.5 nm thick) were first formed at the air–water interface, deposited onto different substrates and characterized using spectroscopic methods, scanning transmission electron microscopy and atomic force microscopy. As a proof of concept, the gas separation performance of MOP-supported membranes has also been evaluated. Selective MOP ultrathin films (thickness ca. 60 nm) exhibit remarkable CO2 permeance and CO2/N2 selectivity, demonstrating the great combined potential of MOP and Langmuir-based techniques in separation technologies.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Pebax® 1041 supported membranes with carbon nanotubes prepared: Via phase inversion for CO2/N2 separation

  • Sánchez-Laínez, Javier
  • Ballester-Catalán, Marcos
  • Javierre-Ortín, Enrique
  • Téllez, Carlos
  • Coronas, Joaquín
This work shows the preparation of Pebax® 1041 films from solutions in DMAc and water-DMAc emulsions as alternatives to those prepared by extrusion that can be found in the literature. These membranes were tested in post-combustion CO2 capture, in the separation of a 15/85 (v/v) CO2/N2 mixture. Self-supported membranes of Pebax® 1041 were prepared by solvent evaporation and phase inversion. The characterization of these films defined the intrinsic properties of this polymer in terms of chemical structure, crystallinity, thermal stability and gas separation performance (a CO2 permeability of 30 Barrer with a CO2/N2 selectivity of 21 at 35 °C and 3 bar feed pressure). Supported Pebax® 1041 membranes were also developed to decrease the Pebax® thickness (in the 1.5-10 µm range), resulting in a higher permeance. These membranes were prepared by a phase inversion process consisting of the precipitation of a Pebax® 1041/DMAc solution in water and dispersing it to form a stable emulsion that was drop-cast on PSF asymmetric supports. Once dried, the polymer formed a dense continuous layer. The phase inversion methodology is "greener" than solvent evaporation since dimethylacetamide is not released as toxic vapour during membrane preparation. The amount drop-cast led to a different selective layer thickness, which was enhanced by the dispersion of MWCNTs in the polymer emulsion. The properties of the Pebax® selective layer were studied by thermogravimetry and by measuring the contact angle of the membrane surface, and the optimal CO2/N2 selectivity (22.6) was obtained with a CO2 permeance of 3.0 GPU.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Conversion of sugars to methyl lactate with exfoliated layered stannosilicate UZAR-S4

  • Murillo, B.
  • de la Iglesia, Ó.
  • Rubio, C.
  • Coronas, J.
  • Téllez, C.
Biomass has been shown as an alternative to fossil fuels for obtaining chemicals. In this work, the transformation of sugars into methyl lactate (ML) at 160 °C was carried out using the layered stannosilicate UZAR-S3 (University of Zaragoza-solid number 3) and the delaminated material UZAR-S4 (University of Zaragoza-solid number 4) obtained from its exfoliation. The exfoliation of UZAR-S3 to UZAR-S4 increased the accessibility of the compounds to the catalytic sites and the medium-strength acidity. Thus, the yield to ML for sucrose transformation increased from 8% for UZAR-S3 to 49.9 % for UZAR-S4. In the reusability tests, the UZAR-S4 catalyst was characterized before and after reaction by several techniques such as X-ray diffraction, thermogravimetry analysis, scanning electronic microscopy, energy dispersive X-ray spectroscopy and nitrogen adsorption. A deactivation of the catalyst was observed, which was related to carbonaceous deposits that decreased the specific surface area and the pore volume of the catalyst.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Functionalized graphene-based polyamide thin film nanocomposite membranes for organic solvent nanofiltration

  • Paseta, L.
  • Luque-Alled, J.M.
  • Malankowska, M.
  • Navarro, M.
  • Gorgojo, P.
  • Coronas, J.
  • Téllez, C.
This work deals with the use of octadecylamine (ODA)-functionalized reduced graphene oxide (rGO) for thin film nanocomposite (TFN) membranes. The functionalization of rGO with ODA leads to graphene-based nanofillers, more hydrophobic than GO, and thus to the easier dispersion in the organic phase of the interfacial polymerization (IP) reaction carried out to produce polyamide (PA) TFN membranes. The performance of the new TFN membranes is evaluated by organic solvent nanofiltration (OSN) of alcoholic solutions containing dyes Acridine Orange (AO, MW 265 g·mol-1), Sunset Yellow (SY, MW 452 g·mol-1) and Rose Bengal (RB, MW 974 g·mol-1). The functionalized nature of the nanoparticles introduced into the hydrophilic PA layer allows an increase of the ethanol permeance from 2.8, 3.4 and 3.7 L·m-2·h-1·bar-1 for AO, SY and RB, respectively, corresponding to the bare thin film composite membrane (without rGO-ODA particles), to 4.3, 4.6 and 6.0 L·m-2·h-1·bar-1 for AO, SY and RB, respectively, for the rGO-ODA based TFN membrane. In fact, we hypothesize that the increase of the ethanol flux achieved with the use of rGO-ODA as a filler in TFN membranes is owing to a combination of the simultaneous presence of polar and non-polar groups from rGO-ODA nanosheets and the creation of still selective narrow gaps between these particles and the polyamide (PA).
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Reseña (Review)

Metal organic framework top-down and bottom-up patterning techniques

  • Ruiz-Zambrana, C.L.
  • Malankowska, M.
  • Coronas, J.
Metal organic frameworks (MOFs) have recently attracted considerable research interest in several fields from coordination chemistry and materials science to engineering and medicine not only due to energy and environmental issues but also due to the need for new paradigms of efficiency and sustainability according to the requirements of the 21st century global society. Because of their crystalline and organic-inorganic nature, they are able to crystallize constituting intergrown architectures ductile enough to be patterned, with the use of appropriate techniques, as nano- and micro-devices with multiple applications. This perspective comprehensively summarizes the recent state of the art in the use of top-down and bottom-up methodologies to create MOF structures with a defined pattern at the nano- and micro-scale.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Synthesis of nanoparticles of zeolitic imidazolate framework ZIF-94 using inorganic deprotonators

  • Madhav, D.
  • Malankowska, M.
  • Coronas, J.
A novel synthesis process of ZIF-94 (also known as SIM-1) is developed for particle size tuning, using either NaOH or NH4OH as a deprotonator. ZIF-94 originate from MOFs and have several advantages over traditional porous materials, in terms of their chemistry, structure and applications as catalysts, adsorbents, biocides and membrane materials. The existing synthesis process for ZIF-94 at a scale-up level produces particles of approximately 250 nm in size; an even smaller size is expected to result in an even better gas separation performance and catalytic activity. In this study, it was found that NaOH results in ZIF-94 particles with well-defined crystal structures, while in the case of NH4OH, the particles agglomerate to produce random shaped bigger particles. The optimum base to metal ratio was found to be 2 : 1 (NaOH : Zn), which shows a compromise between the particle size (114 +/- 3 nm) and BET specific surface area (254 +/- 4 m(2) g(-1)). Furthermore, the synthesized nanoparticles underwent thorough characterization by XRD, TGA, N-2 adsorption and electron microscopy revealing the lowest SEM average particle size of 84 +/- 3 nm.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Green Preparation of Thin Films of Polybenzimidazole on Flat and Hollow Fiber Supports: Application to Hydrogen Separation

  • Sanchez-Lainez, J.
  • Etxeberria-Benavides, M.
  • David, O.
  • Tellez, C.
  • Coronas, J.
This work shows the preparation of thin films, with thickness from 70 nm to 1 mu m, of meta-polybenzimidazole (m-PBI) on polyimide P84 supports. Ethanolic solutions of m-PBI were used to coat flat and hollow fiber supports of asymmetric P84 with m-PBI in a process where the coating and drying was performed at room temperature. A solution of NaOH in EtOH allowed the dissolution of the m-PBI powder, providing the perfect coating solution to build thin films of m-PBI without damaging the polymeric support. It also meant a green alternative, avoiding the use of toxic solvents, such as dimethylacetamide. The resulting membranes have been tested for the separation of H-2 mixtures at high temperature at different setups to allow checking their reproducibility. With 100 nm thickness the membranes showed their best gas separation performance. For flat membranes at 180 degrees C and 3 bar feed pressure a H-2 permeance of 48.5 GPU was obtained, with respective H-2/CO2 and H-2/N-2 selectivities of 33.3 and 55.8. Besides, the hollow fibers under a feed pressure of 6 bar and tested at the same temperature showed near 90 GPU of H-2 with a H-2/CO2 selectivity of 13.5 in the one-fiber module and over 39 GPU of H-2 with a H-2/CO2 selectivity of 20.2 in the five-fiber module. Finally, the stability of the membranes was proved for 22 days at 180 degrees C.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Solventless synthesis of ZIF-L and ZIF-8 with hydraulic press and high temperature

  • Pérez-Miana, M.
  • Reséndiz-Ordóñez, J.U.
  • Coronas, J.
In recent years, alternative methods to conventional synthesis of MOFs (metal-organic frameworks) have emerged due to the problematic use of solvents for both the environment and human health. Here we present the synthesis of ZIFs (zeolitic imidazolate frameworks) at high pressure by means of a hydraulic press provided with a heating mechanism. By the optimization of parameters such as temperature, time and the addition of promotor NH4NO3, a considerable increase in the reaction yield was achieved in products, neither washed nor activated, obtained since the first minute of reaction. Depending on the operation conditions, ZIF-L appeared as competing phase with ZIF-8. Upon transformation of ZIF-L into ZIF-8 in presence of ethanol, a reaction yield of 58.2% was achieved to highly crystalline ZIF-8 with a BET specific surface area of 947 m2/g. This green, fast, versatile and improved method suggests a possible way to future synthesis of other MOFs and the possibility of their industrial implementation.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Sonocrystallisation of ZIF-8 in water with high excess of ligand: Effects of frequency, power and sonication time

  • Nalesso S.
  • Varlet G.
  • Bussemaker M.J.
  • Sear R.P.
  • Hodnett M.
  • Monteagudo-Oliván R.
  • Sebastián V.
  • Coronas J.
  • Lee J.
A systematic study on the sonocrystallisation of ZIF-8 (zeolitic imidazolate framework-8) in a water-based system was investigated under different mixing speeds, ultrasound frequencies, calorimetric powers and sonication time. Regardless of the synthesis technique, pure crystals of ZIF-8 with high BET (Brunauer, Emmett and Teller) specific surface area (SSA) can be obtained in water after only 5 s. Furthermore, 5 s sonication produced even smaller crystals (~0.08 µm). The type of technique applied for producing the ZIF-8 crystals did not have any significant impact on crystallinity, purity and yield. Crystal morphology and size were affected by the use of ultrasound and mixing, obtaining nanoparticles with a more spherical shape than in silent condition (no ultrasound and mixing). However, no specific trends were observed with varying frequency, calorimetric power and mixing speed. Ultrasound and mixing may have an effect on the nucleation step, causing the fast production of nucleation centres. Furthermore, the BET SSA increased with increasing mixing speed. With ultrasound, the BET SSA is between the values obtained under silent condition and with mixing. A competition between micromixing and shockwaves has been proposed when sonication is used for ZIF-8 production. The former increases the BET SSA, while the latter could be responsible for porosity damage, causing a decrease of the surface area. © 2021 The Author(s)
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Enhancement of growth of MOF MIL-68(Al) thin films on porous alumina tubes using different linking agents

  • Perea-Cachero, A.
  • Calvo, P.
  • Romero, E.
  • Téllez, C.
  • Coronas, J.
The preparation of MIL-68(Al) films on the inner surface of alumina tubes is reported. As the direct deposition of the MOF on bare alumina gives poor adhesion results, three different linking agents are employed to achieve a good MOF–support interaction. Colloidal silica LUDOX®, zeolite silicalite-1, and natural polysaccharide chitosan are chosen as binders, because they contain potential functional groups (hydroxy, amino, ether), which can establish hydrogen bonds. While colloidal silica leads to noncontinuous MOF layers, silicalite-1 and chitosan give rise to uniform and well-anchored films, as confirmed by the different characterization techniques used to study the MOF layer. Single-gas permeation experiments are carried out to determine the quality and ideal efficiency of the membranes prepared with silicalite-1 and chitosan. The results for the MIL-68(Al)/silicalite-1 membranes evidence the existence of macrodefects. However, no cracks are found when chitosan is used as a linking agent, and the gas flow through the MIL-68(Al)/chitosan membranes clearly follows Knudsen diffusion.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Greener processes in the preparation of thin film nanocomposite membranes with diverse metal-organic frameworks for organic solvent nanofiltration

  • Paseta, L.
  • Navarro, M.
  • Coronas, J.
  • Téllez, C.
The toxic solvent dimethylformamide has been replaced by the greener dimethylsulfoxide in the casting and activation processes for the preparation of thin film composite (TFC) membranes. This methodology has been validated with the use of MOFs ZIF-8, ZIF-93 and UiO-66 as fillers for thin-film nanocomposite (TFN) membranes. These membranes were successfully applied in the organic solvent nanofiltration of sunset yellow (SY) in methanol obtaining the highest permeance when UiO-66 and ZIF-93 were used with a value of 11 L m -2 h -1 bar -1 . The permeance improvements are related to the MOF porosity, polyamide-MOF layer thickness and the hydrophilic/hydrophobic character of the membrane. © 2019 The Korean Society of Industrial and Engineering Chemistry
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Vapor phase interfacial polymerization: a method to synthesize thin film composite membranes without using organic solvents

  • Paseta, L.
  • Echaide-Górriz, C.
  • Téllez, C.
  • Coronas, J.
Thin film composite membranes (TFC) of polyamide (PA) prepared by interfacial polymerization (IP) between a diamine and an acyl chloride are applied to industrial nanofiltration and reverse osmosis. Water, to dissolve the diamine, and n-hexane, to dissolve the acyl chloride, solvents are involved in the IP process. Eliminating the use ofn-hexane would be crucial to produce a greener TFC membrane synthesis method. This is achieved here by carrying out an interfacial polymerization from the vapor phase. First, the membrane support was impregnated with the aqueous diamine solution. Second, the support with the diamine was contacted with vapors of the acyl chloride to unchain the IP reaction. Besides the absence ofn-hexane, acyl chloride was applied more efficiently avoiding its loss during the cleaning operations carried out in the typical IP process. These membranes were applied in the nanofiltration of simulated micropollutants in water (rose Bengal, sunset yellow and acridine orange dyes), with higher water permeance (up to 3.3 L·m-2·h-1·bar-1) than that of conventional TFC membranes and dye rejections higher than 94% in all cases.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Asymmetric polybenzimidazole membranes with thin selective skin layer containing ZIF-8 for H2/CO2 separation at pre-combustion capture conditions

  • Sánchez-Laínez, J.
  • Zornoza, B.
  • Téllez, C.
  • Coronas, J.
This work addresses an optimization in the fabrication of flat PBI membranes containing ZIF-8 nanoparticles for gas separation purposes. The PBI membranes were prepared in an asymmetric configuration on P84® supports, representing a new way of preparing flat PBI membranes. An optimization of the conditions for the PBI phase inversion preparation method, including the dope composition (in the 15–26 wt% range), has been carried out to obtain PBI membranes with a 1 µm selective skin layer. The asymmetric membranes showed an unprecedented gas separation capacity in pre-combustion CO2 capture, much superior to that of dense membranes, under harsh operating conditions (250 °C and 6 bar feed), performing up to 20.3 GPU of H2 and a H2/CO2 selectivity of 35.6. Their much thinner selective layer made possible the increase in selectivity because of the saturation of the CO2 flow at high pressures. The reduction in the amount of ZIF-8 for obtaining a membrane with the same filler loading (3.7 vs. 9.3 g/m2) was also possible; the performance of this ZIF-8 containig membrane was 22.4 GPU of H2 and a H2/CO2 selectivity of 22.3. The activation energy of the membranes, as well as the flow resistances, were calculated, providing a resistance in series model to understand the flow inside the membrane.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Phase inversion method for the preparation of Pebax® 3533 thin film membranes for CO2/N2separation

  • Martínez-Izquierdo L.
  • Malankowska M.
  • Téllez C.
  • Coronas J.
Thin film composite membranes of poly(ether-block-amide) copolymer Pebax® 3533 were prepared for the first time on asymmetric polysulfone supports by a phase inversion method. The casting solution concentration and the number of layers were varied to study their influence on the selective layer thickness and the gas separation performance. The casting solution concentrations of polymer dissolved in the 1-propanol/1-butanol mixture were 0.25, 0.5, 1.0 and 1.5 wt%. These conditions produced membranes with selective skin layers with thicknesses from 0.2 to 1.8 µm. All the membranes were characterized by scanning electron microscopy, thermogravimetric analysis and infrared spectroscopy. Furthermore, the intrinsic viscosity of all the casting solutions was studied to understand the effect of the polymer concentration on the homogeneity and the gas separation properties of the obtained membranes. In general, lower viscosity of casting solutions rendered to more defective skin layers, resulting in a higher number of layers required to obtain selective membranes. The gas separation performance was tested for the post-combustion 15/85 CO2/N2 mixture at 25-50 °C and under a feed pressure of 3 bar. The best separation performance was achieved with the 0.5 wt% casting solution membranes after the deposition of four polymer layers, obtaining a CO2 permeance of 127 GPU and a CO2/N2 selectivity of 21.4 at 35 °C, the same selectivity of the corresponding dense membrane but with much higher permeance.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Sized-Controlled ZIF-8 Nanoparticle Synthesis from Recycled Mother Liquors: Environmental Impact Assessment

  • García-Palacín, Marta
  • Martínez, José Ignacio
  • Paseta, Lorena
  • Deacon, Adam
  • Johnson, Timothy
  • Malankowska, Magdalena
  • Téllez, Carlos
  • Coronas, Joaquín
The effect of different deprotonators as well as washing steps and drying procedure on the synthesis of ZIF-8 from the mother liquor was investigated. The morphology, thermal stability, crystallinity, and surface area of the synthesized MOF were investigated. In addition, life-cycle assessment (LCA) or, in other words, eco-balance, was implemented as well. LCA compares the full range of environmental effects associated with the product by evaluating all inputs and outputs of material flows and predicting how such flow will affect the environment. ZIF-8 nanocrystals were synthesized from the recycled mother liquors using NaOH or NH4OH thus preserving the main characteristics of the ZIF-8 nanoparticles derived from the initial synthesis. The rest of the characterization methods confirmed the suitability of the synthesis methodology considering the phase purity of the obtained ZIF-8 and nanometer size particles. This procedure enabled us not only to obtain phase pure ZIF-8 but also to substantially decrease the amount of solvent used for washing making it a sustainable process.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Ultrathin films of porous metal-organic polyhedra for gas separation

  • Andrés, Miguel A.|||0000-0003-3691-3437
  • Carné-Sánchez, Arnau|||0000-0002-8569-6208
  • Sanchez-Lainez, Javier|||0000-0001-6627-0079
  • Roubeau, Olivier|||0000-0003-2095-5843
  • Coronas, Joaquin|||0000-0003-1512-4500
  • Maspoch, Daniel|||0000-0003-1325-9161
  • Gascón, Ignacio|||0000-0002-3492-6456
Ultrathin films of a robust Rh-based porous metal-organic polyhedra (MOP) have been obtained. Homogeneous and compact monolayer films (ca. 2.5 nm thick) were first formed at the air-water interface, deposited onto different substrates and characterized using spectroscopic methods, scanning transmission electron microscopy and atomic force microscopy. As a proof of concept, the gas separation performance of MOP-supported membranes has also been evaluated. Selective MOP ultrathin films (thickness ca. 60 nm) exhibit remarkable CO permeance and CO/N selectivity, demonstrating the great combined potential of MOP and Langmuir-based techniques in separation technologies.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Mesoporous Sn-in-MCM-41 catalysts for the selective sugar conversion to methyl lactate and comparative life cycle assessment with the biochemical process

  • Iglesia, Óscar de la
  • Sarango, Miryan
  • Munárriz Tabuenca, Mikel
  • Malankowska, Magdalena
  • Navajas León, Alberto
  • Gandía Pascual, Luis
  • Coronas, Joaquín
  • Téllez, Carlos
The use of biomass for the production of energy and higher added value products is a topic of increasing interest in line with growing environmental concerns and circular economy. Mesoporous material Sn-In-MCM-41 was synthesized for the first time and used as a catalyst for the transformation of sugars to methyl lactate (ML). This catalyst was characterized in depth by various techniques and compared with Sn-MCM-41 and In-MCM-41 catalysts. In the new Sn-In-MCM-41 material, both metals, homogeneously distributed throughout the mesoporous structure of MCM-41, actuate in a cooperative way in the different steps of the reaction mechanism. As a result, yields to ML of 69.4 and 73.9% in the transformation of glucose and sucrose were respectively reached. In the case of glucose, the ML yield 1.5 and 2.6 times higher than those of Sn-MCM-41 and In-MCM-41 catalysts, respectively. The Sn-In-MCM-41 catalyst was reused in the transformation of glucose up to four cycles without significant loss of catalytic activity. Finally, life cycle assessment comparison between chemical and biochemical routes to produce ML allowed us to conclude that the use of Sn-In-MCM-41 reduces the environmental impacts compared to Sn-MCM-41. Nevertheless, to make the chemical route comparable to the biochemical one, improvements in the catalyst and ML synthesis have to be achieved., Financial support from the Grant MAT2016-77290-R funded by MCIN/AEI/10.13039/501100011033 and by 'ERDF A way of making Europe', and Grant T43-20R funded by the Aragón Government are gratefully acknowledged. A.N. and L.M.G. gratefully acknowledge the financial support from Spanish Ministerio de Ciencia, Innovación y Universidades, and the Grant RTI2018-096294-B-C31 funded by ERDF/FEDER. L.M.G. also thanks Banco Santander and Universidad Pública de Navarra for their financial support under 'Programa de Intensificación de la Investigación 2018' initiative.