Pasar al contenido principal

DESARROLLO DE ESCALADO SEMIINDUSTRIAL DE NANOCOMPUESTOS POLIMERICOS BIODEGRADABLES MODIFICADOS CON ACEITES VEGETALES

PID2021-123753NA-C33

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal para Impulsar la Investigación Científico-Técnica y su Transferencia
Subprograma Subprograma Estatal de Generación de Conocimiento
Convocatoria Proyectos de I+D+i (Generación de Conocimiento y Retos Investigación)
Año convocatoria 2021
Plan Estatal 2021-2023 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario UNIVERSITAT POLITÈCNICA DE VALÈNCIA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 15
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Control of Biodegradability Under Composting Conditions and Physical Performance of Poly (Lactic Acid) Based Materials Modified with Phenolic-Free Rosin Resin

  • Rosa-Ramírez, Harrison de la|||0000-0002-2913-7938
  • Ferri, J.M|||0000-0002-1269-4973
  • López-Martínez, Juan|||0000-0001-6904-2282
  • Samper, María-Dolores|||0000-0002-5102-8412
  • Aldas, Miguel
  • Pawlak, Franciszek
[EN] Biodegradable materials based on poly (lactic acid) (PLA) and a phenolic free modified rosin resin were obtained and studied to control the biodegradability under composting conditions of the materials. The resin was blended in concentrations of 1, 3, 5, 10, and 15 parts per hundred (phr) of base polymer using industrial plastic processing techniques. Additionally, to study the effect of the resin on the compatibility of the PLA, the physical performance, water absorption, mechanical behavior, thermal stability, and microstructure of the materials were assessed. The resin incorporation decreased the resistance to thermal degradation of the resultant material, and the composting disintegration rate was slowed down with the increasing content of the resin. The water diffusion was delayed, and the diffusion and corrected diffusion coefficients decreased with the rising content of UP. The mechanical properties tend to decrease while a saturation effect was observed for contents higher than 3 phr of resin. The optimal amount of resin that can be added to achieve good interaction with PLA matrix, complete miscibility, and good material cohesion is 3 phr., Open Access funding provided thanks to the CRUE-CSIC agreement with Springer Nature. This research was funded by MCIN/AEI/10.13039/501100011033 through PID-AEI Project (grant PID2021-123753NA-C33 and PID2020-116496RB-C22) and TED-AEI Project (grants TED2021-129920A-C43), and, as appropriate, by "ERDF A way of making Europe", by the "European Union" or by the "European Union NextGenerationEU/PRTR.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Pentaerythritol and Glycerol Esters Derived from Gum Rosin as Bio-Based Additives for the Improvement of Processability and Thermal Stability of Polylactic Acid

  • Rosa-Ramírez, Harrison de la|||0000-0002-2913-7938
  • Ferri, J.M|||0000-0002-1269-4973
  • López-Martínez, Juan|||0000-0001-6904-2282
  • Samper, María-Dolores|||0000-0002-5102-8412
  • Dominici, Franco
  • Luzi, Francesca
  • Puglia, Debora
  • Torre, Luigi
[EN] Gum rosin esters are some of the most common gum rosin derivatives used in different applications, such as coatings, paper, varnishes, chewing gum, and food industries. In this study, gum rosin esters are used as additives for polylactic acid (PLA) to improve its processability and thermal stability. Blends of an amorphous PLA with two different gum rosin esters, pentaerythritol ester and glycerol ester, were prepared by melt extrusion process in concentrations from 1, 3, and 5 phr. Besides the comparison of thermal degradation, microstructure assessment, and melt flow index (MFI) analysis, the processability performance during testing samples production by injection molding process was evaluated. Experimental results showed that MFI values of PLA-gum rosin ester blends increased by 100%, 147%, and 164%, along with increasing content of gum rosin esters addition, in both cases. Also, both derivatives slightly improved PLA thermal stability (around 3ºC higher). Injection molding temperature decreased by at least 20 °C for PLA-gum rosin ester blends compared with neat PLA. Furthermore, the maximum tensile strength of PLA-gum rosin esters was negligibly affected in formulations with low content of gum rosin esters, and the FESEM images revealed a good dispersion and compatibility of gum rosin ester particles into PLA matrix in both concentrations., This research was funded by MCIN/AEI/10.13039/501100011033 through PID-AEI Project (grant PID2021-123753NA-C33 and PID2020-116496RB-C22) and TED-AEI Project (grants TED2021-129920 A-C43), and, as appropriate, by "ERDF A way of making Europe", by the "European Union" or by the "European Union NextGenerationEU/PRTR".Open Access funding provided thanks to the CRUE-CSIC agreement with Springer Nature.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Nanoparticles From Infusion Beverage Wastes and Their Effect on PLA/PHB Plasticized Composite Behavior

  • Sempere-Torregrosa, Jaume|||0000-0002-8742-0301
  • Rosa-Ramírez, Harrison de la|||0000-0002-2913-7938
  • Samper, María-Dolores|||0000-0002-5102-8412
  • Dominici, Franco
  • Puglia, Debora
  • Torre, Luigi
[EN] In this work, yerba mate (nYM) and black tea (nBT) nanoparticles were extracted from Ilex paraguariensis and Camellia sinensis, respectively. Unlike traditional biocomposites and additives, this approach valorizes the waste of infusion beverages without using chemical compounds. Nanoparticles underwent preliminary TGA analysis, showing stable and high degradation temperature, making them suitable for processing with the selected polymer matrix. Subsequently, they were incorporated into the selected PLA (75%)-PHB (25%) blend plasticized with maleinized corn oil (MCO) at a concentration of 1-3 wt.%. Tensile characterization of the PLA-PHB blend plasticized with MCO showed an improvement in compatibility between polymers, with increased ductility. The plasticizing effect of MCO was confirmed by calorimetric analysis, showing a remarkable decrease in Tg value. The combination of MCO and nanoparticles continues to exhibit enhanced thermal stability, showing functional nanofiller behavior. Moreover, the presence of nanoparticles enhanced the barrier property of the plasticized films toward oxygen barrier properties, reducing the OTR-e values. Finally, during the second half of the composting test, it was observed that nanoparticle addition delayed the degradation process; otherwise, it continued showing interesting biodegradable properties. These findings open multiple possibilities in the combined use of infusion beverage waste nanoparticles and modified vegetable oils to develop sustainable packaging applications., This research was funded by MCIN/AEI/10.13039/501100011033 through the PID-AEI Project (grant PID2021-123753NA-C33) and the TED- AEI Project (grant TED2021-129920A-C43) and, as appropriate, by "ERDF A way of making Europe", by the "European Union" or by the "European Union NextGenerationEU/PRTR". M.D. Samper thanks the Spanish Ministerio de Ciencia, Innovacin y Universidades for the funding received for the Jose Castillejo mobility stay (grant CAS21/00379).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Odour characterisation of high-density polyethylene recycled with sepiolite by sensory evaluation

  • Samper, María-Dolores|||0000-0002-5102-8412
  • Pavón-Vargas, Cristina Paola|||0000-0003-2902-0059
  • Rodríguez-Rego, Jesus M.
  • Mendoza-Cerezo, Laura
  • Marcos-Romero, Alfonso C.
[EN] In recent years, the production and consumption of plastics has increased. This growth in production has resulted in an increasing amount of plastic waste, which is a global problem. Among plastics, high density polyethylene (HDPE) is one of the most widely used polymers in the packaging industry, so its waste is used in the recycling process. One of the main disadvantages of accepting recycled HDPE in production processes is its odour, which makes it impossible to use in production lines. The aim of this work is to reduce and/or eliminate the odours present in the HDPE samples selected for recycling through the use of sepiolites. FTIR analysis of the HDPE samples sent for recycling showed the presence of small amounts of polypropylene (PP), (PET), flexible polyurethane, dirt and adhesives, which could be the cause of the bad odour. Washing the sample showed a decrease in odour, probably due to the removal of dirt and other products that can lead to the degradation of the plastics responsible for the odour. The characterisation of the mixture of sepiolites and HDPE aims to analyse the mechanical and thermal stability of the sample. Not only can pre-washing lead to odour reduction, but also extrusion and injection processes at elevated temperatures can lead to the removal of volatile or semi-volatile compounds. Sensory analysis showed a reduction in odour in HDPE samples with sepiolites, particularly with 15% Pensil sepiolite, to the detriment of mechanical stability. At lower concentrations of sepiolite, the results are good from a sensory, mechanical and thermal point of view, which could mean an industrial application in the manufacture of benches, flower pots, etc., The author(s) disclosed receipt of the following financial support for the research, authorship, and/or publication of this article: This work was supported by the ERDF A way of making Europe and State Investigation Agency (PID2021-123753NA-C33 and PID2020-116496RB-C22) and European Union Next Generation EU/PRTR and MCIN/AEI.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Thermal and Mechanical Performance of Maleic Anhidride/Benzoyl Peroxide-Modified PLA/PCL Biocomposites

  • Unamuno-Garay, Aritz
  • Llidó Barragán, Alexandra|||0009-0006-4847-8048
  • Ferrándiz Bou, Santiago|||0000-0001-7137-9298
  • Samper, María-Dolores|||0000-0002-5102-8412
[EN] This study investigated PLA/PCL blends modified with maleic anhydride (MA) via radical grafting using benzoyl peroxide (BPO) as an initiator. Different formulations with 5 and 10 wt.% of PLA-g-MA (containing 1, 3, and 5 wt.% MA) were prepared to evaluate their compatibilizing effect. Samples were characterized thermally, mechanically, and morphologically using DSC, TGA, FTIR, goniometry, SEM, and tensile, impact, and hardness tests. The results show that adding PCL significantly improves the ductility of PLA, though it reduces tensile strength and hardness. Grafting with MA partially improves phase compatibility, as seen by increased elongation at break and impact resistance, especially at intermediate MA concentrations (1¿3%). However, higher MA contents lead to greater variability in thermal and mechanical results, likely due to heterogeneous phase dispersion. FTIR analysis detected residual BPO in some formulations, though below 0.1 phr. TGA indicated a slight improvement in thermal stability at 5 wt.% MA. Overall, the findings suggest that controlled use of MA as a compatibilizer enhances the balance of mechanical and thermal properties in PLA/PCL systems., The authors acknowledge the I+D+i PID2021-123753NA-C33 project by MCIN/AEI/10.13039/ 501100011033 and by FEDER A way of making Europe , as well as the TED2021-129920A-C43 project by MCIN/AEI/10.13039/501100011033 and by Unión Europea NextGenerationEU/PRTR .
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Tribology behaviour of graphene-modified nanostructured Al2O3 3 %TiO2 coatings under boundary and mixed lubrication conditions

  • Habib, K.A.
  • Cano, D.L.
  • Serrano-Mira, J.
  • Abellán-Nebot, José V.
  • Dosta, S.
  • E. Rayón|||0000-0002-0653-2046
[EN] This study is focused on the preparation of a self-lubricating coating via thermal spraying. This coating was designed to control friction and lubrication in both boundary lubrication (BL) and mixed lubrication (ML) regimes. We aimed to compare the tribological behaviour of nanostructured Al 2 O 3 /3 % TiO 2 and modified nanostructured Al 2 O 3 /3 % TiO 2 incorporating 3 % GNPs coatings deposited by Oxygen -Fuel (OF). The critical conditions for the transition from BL to ML were experimentally studied using a fundamental tribological concept known as the Stribeck curve. A lubricating film consisting of detached GNPs, Al 2 O 3 nanoparticle debris, and a conventional lubricant effectively covers the surface material and improves the mechanochemical interactions between the surface material and lubricating oil, thereby enhancing the tribological performance. The introduction of GNPs is found to play an effective role in the lubrication regime, leading to an increase in microhardness, a decrease in the friction coefficient and wear volume of the Al 2 O 3 /3 % TiO 2 coating, and the steel counterpart disc. It noticeably improved the critical load-carrying capacity at different speeds during the transition from BL to ML regimes. The tribo-layer formed on the worn surfaces controls the tribological properties of the Al 2 O 3 /3 % TiO 2 + 3 % GNPs coatings., MGS (David Leal Cano) supported by the Margarita Salas post-doctoral contract MGS/2021/10 (UP2021-021) financed by the European Union-NextGenerationEU. This research was funded by by MCIN/AEI/10.13039/501100011033 through PID-AEI Project (grant PID2021-123753NA- C33) , and, as appropriate, by "ERDF A way of making Europe", by the "European Union" or by the "European Union NextGenerationEU/PRTR"
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Plastics from end-of-life vehicles: material insights to support circular economy-oriented recycling strategies

  • Vazquez, Yamila Victoria
  • Pavón-Vargas, Cristina Paola|||0000-0003-2902-0059
  • Samper, María-Dolores|||0000-0002-5102-8412
  • López-Martínez, Juan|||0000-0001-6904-2282
[EN] Plastic waste from End-of-Life Vehicles (ELVs) represents a growing challenge for sustainable waste management due to its complex composition, presence of additives, and variable recyclability. This study presents a detailed characterization of two representative plastic fractions from ELV components using spectroscopic, thermal, morphological, and rheological analyses. The main polymeric systems identified were polycarbonate-polybutylene terephthalate (PC/PBT) and polycarbonate-polyethylene terephthalate (PC/PET), both containing mineral fillers such as talc, quartz, clays, and titanium dioxide. These fillers were confirmed by thermogravimetric analysis, X-ray diffraction, and electron microscopy, and shown to influence degradation patterns and material morphology. Significant differences in melt flow behavior and structural features were observed between the two fractions, indicating distinct processing responses and recyclability profiles. These findings provide a critical foundation for designing efficient mechanical recycling and upcycling strategies for ELV plastics, directly supporting the development of a circular economy in the automotive sector. The methodology presented is transferable to other complex post-consumer waste streams, supporting broader circular economy goals through improved material traceability and resource efficiency., This research was funded by MCIN/AEI/https://doi.org/10.13039/501100011033 through grant PID2023-152869OB-C22 by the European Union NextGenerationEU /PRTR and PID-AEI Project (grant PID2021-123753NA-C33) and ERDF A way of making Europe by the European Union.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

High-Performance PA6 Composites Reinforced with Recycled Aramid Fibers from Firefighter Protective Clothing

  • Marco-Sanjuan, Joaquin
  • Lázaro-Hernández, C.|||0009-0002-8250-9363
  • Mario Nicolás
  • Fenollar, Octavio|||0000-0003-4323-7414
[EN] The recycling of technical textile waste represents a major challenge due to the complex and multilayered structure of these materials. Firefighter protective clothing, mainly composed of high-performance aramid fibers combined with polymeric membranes and auxiliary textile components, is commonly landfilled or incinerated at the end of its service life, resulting in a significant environmental impact. This work utilized recycled aramid-rich textile waste obtained from end-of-life firefighter protective clothing as reinforcement for polyamide 6 to develop high-performance thermoplastic composites within a circular economy framework. Composites containing 15, 30, 45, and 60 wt.% of recycled textile waste were manufactured by melt compounding followed by injection molding. In addition, a selected formulation containing 30 wt.% reinforcement was compatibilized using an amino-functional silane to improve interfacial adhesion. The materials were systematically characterized in terms of tensile properties, thermal be-havior, thermomechanical performance, water uptake, flammability, colorimetric properties, and fracture morphology by field emission scanning electron microscopy. The results revealed a pronounced increase in stiffness and thermomechanical stability, with tensile strength increasing from approximately 65 MPa for neat PA6 up to 78 MPa at 30 wt.% reinforcement, and elastic modulus exceeding 5000 MPa at high reinforce-ment contents. An optimal balance between mechanical performance and ductility was achieved at 30 wt.% reinforcement, while higher contents enabled a substantial exten-sion of the service temperature range, with HDT values increasing from 55 °C for neat PA6 up to 173 °C for highly reinforced systems. FESEM analysis confirmed improved interfacial adhesion in silane-compatibilized systems, explaining the enhanced me-chanical and thermomechanical behavior. Furthermore, the incorporation of recycled aramid-rich textile waste led to a significant improvement in flame retardancy, enabling UL-94 V-0 classification at 30 wt.% reinforcement and above, without the use of addi-tional flame-retardant additives, enabling UL-94 V-0 classification without additional flame-retardant additives. Overall, this study demonstrates the technical feasibility and high added-value potential of valorizing firefighter protective clothing waste into ad-vanced PA6-based composites with enhanced mechanical, thermal, and fire-resistant properties, providing a sustainable route for the valorization of high-performance textile waste., This research was partially supported by the Spanish Ministry of Science and Innovation through the projects PID2020-116496RB-C22 and PID2021-123753NA-C33 funded by MCIN/AEI/10.13039/501100011033. Additional funding was provided by project TED2021-131762AI00, funded by the European Union NextGenerationEU/PRTR. Part of the research activities were also developed within the framework of the UP-CIRCULAR and TEXPLAST projects funded by the Conselleria de Innovación, Industria, Comercio y Turismo of the Generalitat Valenciana through IVACE (IMAM-CA/2024/6 and IMAM-CA/2023/6).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Biodegradable active packaging films reinforced with thyme waste nanoparticles

  • Sempere-Torregrosa, Jaume|||0000-0002-8742-0301
  • Samper, María-Dolores|||0000-0002-5102-8412
  • Arrieta, Marina Patricia
  • Dominici, F.
  • Debora Puglia, Debora Puglia
  • Torre, Luigi
[EN] This present work introduces a novel strategy combining nanoparticles from thymus vulgaris (nT) infusion waste, incorporated at 1 wt% and 3 wt%, with maleinized corn oil (MCO) as a natural plasticizer into PLA-PHB blend (75 wt% PLA, 25 wt% PHB) The materials were processed by micro-extrusion into films intended for sustainable and biodegradable active packaging applications. Nanoparticle formulation with 3 wt% showed high variation in tensile properties compared to MCO blend with 41% and 75% decrease in tensile strength and elongation at break respectively, otherwise both nanoparticles¿ formulations still exhibit increase on ductile reaching 74% and 49% for 1¿3 wt% on elongation at break compared with neat PLA. Plasticizer effect of MCO and interaction of nT nanoparticles with the blend was confirmed by calorimetric analysis, showing Tg 15% and 9% decrease for 1¿3 wt% respectively. Results of colour and UV characterization suggest that the films could interfere with light incidence while maintaining high transparency. During composting test, it was observed that the addition of nanoparticles delayed the degradation grade, although all samples were composted within 30 days. Furthermore, the nanoparticles improved the oxygen barrier properties of developed films, leading to a reduction of above 40% for both nanoparticles¿ formulations in OTR-e values. In addition, nanoparticles highly increased antioxidant activity with 67% and 75% for 1¿3 wt%, interesting findings to develop sustainable, biodegradable and active materials for food packaging applications., This research was supported by I+D+i PID2021-123753NA-C32 and PID2021-123753NA-C33 projects by MCIN/AEI/https://doi.org/10.13039/501100011033 and by FEDER A way of making Europe , as well as the TED2021-129920 A-C43 and CNS2022-136064 projects by MCIN/AEI/https://doi.org/10.13039/501100011033 and by Unión Europea NextGenerationEU/PRTR.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Effect of Epoxidized and Maleinized Corn Oil on Properties of Polylactic Acid (PLA) and Polyhydroxybutyrate (PHB) Blend

  • Sempere-Torregrosa, Jaume|||0000-0002-8742-0301
  • Ferri, J.M|||0000-0002-1269-4973
  • Rosa-Ramírez, Harrison de la|||0000-0002-2913-7938
  • Pavón-Vargas, Cristina Paola|||0000-0003-2902-0059
  • Samper, María-Dolores|||0000-0002-5102-8412
[EN] The present work analyzes the influence of modified, epoxidized and maleinized corn oil as a plasticizing and/or compatibilizing agent in the PLA¿PHB blend (75% PLA and 25% PHB wt.%). The chemical modification processes of corn oil were successfully carried out and different quantities were used, between 0 and 10% wt.%. The different blends obtained were characterized by thermal, mechanical, morphological, and disintegration tests under composting conditions. It was observed that to achieve the same plasticizing effect, less maleinized corn oil (MCO) is needed than epoxidized corn oil (ECO). Both oils improve the ductile properties of the PLA¿PHB blend, such as elongation at break and impact absorb energy, however, the strength properties decrease. The ones that show the highest ductility values are those that contain 10% ECO and 5% MCO, improving the elongation of the break of the PLA¿PHB blend by more than 400% and by more than 800% for the sample PLA., This work was supported by the Spanish Ministry of Science and Innovation, NANOCIRCOIL (PID2021-123753NA-C33)
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Polybutylene succinate film incorporating essential oil as active packaging materials to prolong tomatoes shelf-life

  • Barrino, Federico
  • Finamore, Rosario
  • Mirpoor, Seyedeh Fatemeh
  • Schiraldi, Chiara
  • Rosa-Ramírez, Harrison de la|||0000-0002-2913-7938
  • Sempere-Torregrosa, Jaume|||0000-0002-8742-0301
  • López-Martínez, Juan|||0000-0001-6904-2282
  • Samper, María-Dolores|||0000-0002-5102-8412
[EN] The present research work deals with the laboratory scale manufacturing of thin films based on polybutylene succinate (PBS), a sustainably obtained biodegradable polyester (bioplastic), with the aim to propose their use in food packaging in order to slow down the food degradation process, to replace the polymers derived from fossil fuels. To this purpose, thin films of (PBS) were prepared by adding diverse Mediterranean herbs extracts up to 3 % by weight. Specifically, PBS was added with three different types of natural oils/extracts: thymol, carvacrol, and basil extract (mainly rich in eugenol). These compounds, well known for their antioxidant and antimicrobial potential, conferred functional activity to the films. The resulting materials were characterized in terms of chemical, thermal, optical, mechanical, and gas permeability properties, as well as antioxidant activity and preliminary food-contact tests. Tomatoes wrapped in the active films showed delayed oxidative browning and reduced microbial spoilage during three weeks of storage. Among the various formulations, the blend containing all essential oils (PBS/All) offered the best compromise between thermal stability, structural compactness, and preservation capacity. These results suggest that PBS/All films are promising candidates for sustainable active packaging applications., This research was partially funded by MCIN/AEI/10.13039/501100011033 through the PID-AEI Project (grant PID2021-123753NA-C33) , Project (grant PID2024-157368NB-C33) and the TED-AEI Project (grant TED2021-129920A-C43) and, as appropriate, by "ERDF A way of making Europe", by the "European Union" or by the "European Union NextGenerationEU/PRTR". This research was partially funded by Bionutra Project (Italian Ministry of Research) .
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Influence of the Presence of Poly(butylene succinate) in the Poly(ethylene terephthalate) Recycling Process

  • Pavón-Vargas, Cristina Paola|||0000-0003-2902-0059
  • Rosa-Ramírez, Harrison de la|||0000-0002-2913-7938
  • Samper, María-Dolores|||0000-0002-5102-8412
  • López-Martínez, Juan|||0000-0001-6904-2282
  • Aldás, Miguel
  • Bertomeu, David
[EN] Poly(butylene succinate) (PBS) is one of the contaminants in the Poly(ethylene terephthalate) (PET) recycling process. It is known that high contents of PBS in PET significantly reduce PET properties, but the effect of low contents on PET has yet to be studied. This work studied the influence of low contents of PBS on recycled PET. Five formulations of PBS in PET were prepared, and the properties of relative affinity, mechanical, thermal, and disintegration under composting conditions were assessed. The solubility parameter indicated that PET and PBS are miscible. However, FESEM images show slight marks of immiscibility, and the mechanical characterization results showed that PBS, even in low contents, reduced the mechanical properties of recycled PET, which proves that the materials are not miscible in the studied contents. The DSC results indicated that PBS could not be quickly detected in PET. However, its presence can be inferred by the reduction in PET crystallization degree. Finally, the presence of PBS up to 15 wt.% does neither affect the disintegration under composting conditions nor the thermal stability of recycled PET. The drop in mechanical properties shows that PBS must be removed from the PET waste stream to preserve the quality of the material., This research is a part of grant PID2020-116496RB-C22, funded by MCIN/AEI/10.13039/ 501100011033. C.P. acknowledges the Santiago Grisolía Fellowship (GRISOLIAP/2019/113) from Generalitat Valenciana. The Microscopy Services at UPV are also acknowledged for their help in collecting and analyzing the images
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Preparation and Characterization of New Bioplastics Based on Polybutylene Succinate (PBS)

  • Barrino, Federico
  • Schiraldi, Chiara
  • Rosa-Ramírez, Harrison de la|||0000-0002-2913-7938
  • López-Martínez, Juan|||0000-0001-6904-2282
  • Samper, María-Dolores|||0000-0002-5102-8412
[EN] Sea and environmental pollution due to microplastics are global problems that in recent years have attracted particular interest in the scientific community. The increase in the world population and the consequent consumerism of non-reusable materials are amplifying these problems. In this manuscript, we present novel bioplastics, which are completely biodegradable, for their potential use in food packaging, to replace fossil-fuel-derived plastic films and slow food degradation due to oxidative processes or microbial contamination. In this study, thin films based on polybutylene succinate (PBS) were prepared to reduce pollution, and different percentages by weight (1, 2 and 3 wt%) of extra virgin olive oil (EVO) and coconut oil (CO) were included to improve the chemico-physical properties of the polymer and possibly improve the functionality of the films in terms of prolonged food preservation. Attenuated total reflectance Fourier transform infrared (ATR/FTIR) spectroscopy was used to evaluate the interactions between the polymer and the oil. Furthermore, the mechanical properties and thermal behavior of the films were evaluated as a function of the oil content. A scanning electron microscopy (SEM) micrograph showed the surface morphology and the thickness of the materials. Finally, apple and kiwi were selected for a food-contact test, and the wrapped sliced fruit was monitored and evaluated for 12 days to macroscopically evaluate the oxidative process and/or eventually occurring contamination. The films were shown to reduce the browning of sliced fruit due to oxidation, and no molds were evidenced up to 10/12 days of observation with the addition of PBS, with 3 wt% of EVO achieving the best outcomes., This research was funded by MCIN/AEI/10.13039/501100011033 through PID-AEI Project (grant PID2021-123753NA-C33 and PID2020-116496RB-C22), TED-AEI Project (grants TED2021-129920A-C43), and, as appropriate, by ERDF: A way of making Europe , by the European Union , or by the European Union NextGenerationEU/PRTR .
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

The Influence of Different Sustainable Silk-Based Fillers on the Thermal and Mechanical Properties of Polylactic Acid Composites

  • Ferri, J.M|||0000-0002-1269-4973
  • E. Rayón|||0000-0002-0653-2046
  • Samper, María-Dolores|||0000-0002-5102-8412
  • Aldas, Miguel
  • Lozano-Pérez, Antonio Abel
[EN] In this work, different silk fillers combined with maleinized corn oil (MCO), as environmentally friendly plasticizers, were used to modify the mechanical and thermal properties of polylactic acid (PLA) composites. Melt extrusion and injection were used to obtain samples with a content of 10 wt.% of MCO and 0.5 phr of different silk fillers: crushed silk (CS), silk fibroin microparticles (SFM), and silk fibroin nanoparticles (SFN). PLA formulation with 10 wt.% of MCO and 0.5 g of CS per hundred grams of composite (phr) showed the highest increase in mechanical ductile properties with an increase in elongation at break of approximately 1400%, compared with PLA. Differential scanning calorimetry (DSC) showed a decrease of 2 degrees C in their glass transition temperature with the addition of different silk fillers. In addition, SFM and SFN increase the degree of crystallinity of PLA. This increment was also confirmed by infrared spectroscopy analysis. Field emission scanning electron microscopy (FESEM) images revealed a good dispersion of the different silk fillers. Among them, PLA formulation with 10 wt.% MCO and 0.5 phr of SFN, showed an optimal balance between maximum resistance and elongation at break, with 52.0 MPa and 10.8%, respectively, improving elongation at break by 635%. Furthermore, all samples were satisfactorily disintegrated under composting conditions., This research was funded by the Spanish Research Agency (PDC2021-121345-C22.), the Spanish Ministry of Science and Innovation, (Grant No. PID2021-123753NA-C33) and partially supported (80%) by the European Commission ERDF/FEDER Operational Program Murcia CCI No. 2007ES161PO001 (Project No. 14-20/20). The research contract of Dr. J.M. Ferri was funded by Generalitat Valenciana (Grant No. APOSTD/2019/122).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Bio-Based and Biodegradable Polymeric Materials for a Circular Economy

  • Oliver-Cuenca, Víctor
  • Salaris, Valentina
  • Muñoz Gimena, Pedro Francisco
  • Agüero, Ángel
  • Peltzer, M.
  • Montero, Victoria Alcázar
  • Arrieta, Marina P.
  • Sempere-Torregrosa, Jaume
  • Pavon, Cristina
  • Samper, M. D.
  • Rodríguez Crespo, Gema
  • Kenny, José María
  • López, Daniel
  • Peponi, Laura
Nowadays, plastic contamination worldwide is a concerning reality that can be addressed with appropriate society education as well as looking for innovative polymeric alternatives based on the reuse of waste and recycling with a circular economy point of view, thus taking into consideration that a future world without plastic is quite impossible to conceive. In this regard, in this review, we focus on sustainable polymeric materials, biodegradable and bio-based polymers, additives, and micro/nanoparticles to be used to obtain new environmentally friendly polymeric-based materials. Although biodegradable polymers possess poorer overall properties than traditional ones, they have gained a huge interest in many industrial sectors due to their inherent biodegradability in natural environments. Therefore, several strategies have been proposed to improve their properties and extend their industrial applications. Blending strategies, as well as the development of composites and nanocomposites, have shown promising perspectives for improving their performances, emphasizing biopolymeric blend formulations and bio-based micro and nanoparticles to produce fully sustainable polymeric-based materials. The Review also summarizes recent developments in polymeric blends, composites, and nanocomposite plasticization, with a particular focus on naturally derived plasticizers and their chemical modifications to increase their compatibility with the polymeric matrices. The current state of the art of the most important bio-based and biodegradable polymers is also reviewed, mainly focusing on their synthesis and processing methods scalable to the industrial sector, such as melt and solution blending approaches like melt-extrusion, injection molding, film forming as well as solution electrospinning, among others, without neglecting their degradation processes., This research was funded by the Agencia Estatal de Investigación (AEI, MICINN, Spain), and Fondo Europeo de Desarrollo Regional (FEDER, EU), PID2021-123753NB-C31, PID2021-123753NA-C32, PID2021-123753NA-C33, and NextGenerationEU MRR TED2021-129335B-C21. V.O.-C. acknowledges Spanish government for the grant PRE2020-103097 funded by MCIN/AEI/10.13039/501100011033 and “ESF Investing in your future”. The authors want to know MICIN for PID2021-123753NB-C31 and TED2021-129335B-C21 projects and for RED2022-134806-T., Peer reviewed