Pasar al contenido principal

ESTUDIO DE LA OBTENCION DE REFUERZOS ACTIVOS PARA BIOPOLIMEROS EN LA ECONOMIA CIRCULAR

PID2021-123753NA-C32

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal para Impulsar la Investigación Científico-Técnica y su Transferencia
Subprograma Subprograma Estatal de Generación de Conocimiento
Convocatoria Proyectos de I+D+i (Generación de Conocimiento y Retos Investigación)
Año convocatoria 2021
Plan Estatal 2021-2023 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario UNIVERSIDAD POLITECNICA DE MADRID

Resultados relacionados

Resultados totales (Incluyendo duplicados): 14
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Processing Compostable PLA/Organoclay Bionanocomposite Foams by Supercritical CO2 Foaming for Sustainable Food Packaging

  • Faba, Simón
  • Arrieta, Marina P.
  • Agüero, Ángel
  • Torres, Alejandra
  • Romero, Julio
  • Rojas, Adrián
  • Galotto, María José
[EN] This article proposes a foaming method using supercritical carbon dioxide (scCO(2)) to obtain compostable bionanocomposite foams based on PLA and organoclay (C30B) where this bionanocomposite was fabricated by a previous hot melt extrusion step. Neat PLA films and PLA/C30B films (1, 2, and 3 wt.%) were obtained by using a melt extrusion process followed by a film forming process obtaining films with thicknesses between 500 and 600 mu m. Films were further processed into foams in a high-pressure cell with scCO(2) under constant conditions of pressure (25 MPa) and temperature (130 degrees C) for 30 min. Bionanocomposite PLA foams evidenced a closed cell and uniform cell structure; however, neat PLA presented a poor cell structure and thick cell walls. The thermal stability was significantly enhanced in the bionanocomposite foam samples by the good dispersion of nanoclays due to scCO(2), as demonstrated by X-ray diffraction analysis. The bionanocomposite foams showed improved overall mechanical performance due to well-dispersed nanoclays promoting increased interfacial adhesion with the polymeric matrix. The water uptake behavior of bionanocomposite foams showed that they practically did not absorb water during the first week of immersion in water. Finally, PLA foams were disintegrated under standard composting conditions at higher rates than PLA films, showing their sustainable character. Thus, PLA bionanocomposite foams obtained by batch supercritical foaming seem to be a sustainable option to replace non-biodegradable expanded polystyrene, and they represent a promising alternative to be considered in applications such as food packaging and other products., This research was funded by the National Commission for Scientific and Technological Research (ANID) through the Project Fondecyt Regular 12011301 and by the Spanish Ministry of Science and Innovation (MICINN) through the PID-AEI project (grant number PID2021-123753NAC32) funded by MCIN/AEI/10.13039/501100011033 and by ERDF "A way of making Europe" by the "European Union". Ph.D. student Simon Faba gratefully acknowledges ANID for its financial support from the National Doctoral Scholarship with the grant number 21200851 as well as with the research mobility fellow (number 75210123). Ph.D. Angel Aguero acknowledges the Margarita Salas postdoctoral grant from the Ministerio de Universidades, Spain, funded by the European Union-Next Generation EU.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Foaming of 3D-Printed PLA/CaCO3 Composites by Supercritical CO2 Process for Sustainable Food Contact Materials

  • Faba, Simón
  • Agüero, Ángel
  • Arrieta, Marina P.
  • Martínez, Sara
  • Romero, Julio
  • Torres, Alejandra
  • Galotto, María José
[EN] In the last decade, among the emerging technologies in the area of bioplastics, additive manufacturing (AM), commonly referred to as 3D printing, stands out. This technology has gained great interest in the development of new products, mainly due to its capability to easily produce customized and low-cost plastic products. This work aims to evaluate the effect of supercritical foaming of 3D-printed parts based on a commercial PLA matrix loaded with calcium carbonate, for single-use sustainable food contact materials. 3D-printed PLA/CaCO3 parts were obtained by 3D printing with a 20% and 80% infill, and two infill patterns, rectilinear and triangular, were set for each of the infill percentages selected. Supercritical fluid foaming of PLA/CaCO3 composite printed parts was performed using a pressure of 25 MPa, a temperature of 130 degrees C for 23 min, with a fast depressurization rate (1 s). Closed-cell foams were achieved and the presence of CaCO3 did not influence the surface of the foams or the cell walls, and no agglomerations were observed. Foam samples with 80% infill showed subtle temperature fluctuations, and thermogravimetric analysis showed that samples were thermally stable up to similar to 300 degrees C, while the maximum degradation temperature was around 365 degrees C. Finally, tensile test analysis showed that for lower infill contents, the foams showed lower mechanical performance, while the 80% infill and triangular pattern produced foams with good mechanical performance. These results emphasize the interest in using the supercritical CO2 process to easily produce foams from 3D-printed parts. These materials represent a sustainable alternative for replacing non-biodegradable materials such as Expanded Polystyrene, and they are a promising option for use in many industrial applications, such as contact materials., Simón Faba gratefully acknowledges the National Commission for Scientific and Technological Research, ANID, for its financial support from the Postdoctoral Scholarship abroad (grant number 74230053). Authors thank the financial support of CEDENNA (AFB 220001 Project) and the Spanish Ministry of Science and Innovation (MICINN) through the PID-AEI project (grant PID2021-123753NA-C32) funded by MCIN/AEI/10.13039/501100011033 and by ERDF A way of making Europe by the European Union as well as the TED-AEI project (grant TED-129920A-C43) and Research consolidation project (grant CNS2022-136064) funded by MCIN/AEI/10.13039/501100011033 and by the European Union NextGenerationEU/PRTR . Ángel Agüero acknowledges the Margarita Salas post-doctoral grant from the Ministerio de Universidades, Spain, funded by the Recovery, Transformation, and Resilience Plan financed by the European Union NextGenerationEU. The co-financing of the project FONDECYT-ANID (grant number 1230795) is also acknowledged.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Capítulo o parte de un libro (BookPart)

Introduciendo los ODS y la circularidad a la educación en ingeniería a través de actividades para el reciclado de plásticos en un campus universitario

  • Agüero Rodríguez, Ángel
  • Hidalgo-Carvajal, David
  • Lascano, Diego
  • Sepúlveda, Javiera
  • Arrieta, Marina Patricia
  • Carrasco-Gallego, Ruth
  • M. Muneta, María Luisa
[ES] Atendiendo a la vinculación directa de los objetivos de desarrollo sostenible (ODS) con el mundo ingenieril, en este trabajo se plantea una actividad docente centrada en fomentar la economía circular de la Escuela Técnica Superior de Ingenieros Industriales de la Universidad Politécnica de Madrid, mediante la revalorización de residuos plásticos generados en la Escuela mediante reciclado mecánico. La actividad consiste en la fabricación de filamento 3D empleando residuos de piezas impresas defectuosas que han sido fabricadas en la escuela utilizando un plástico biobasado y biodegradable, el poli(ácido láctico) (PLA), para la generación de nuevos productos por impresión 3D y, posteriormente, comprobar la compostabilidad de dichos productos demostrando que se integran completamente en la economía circular. Los estudiantes conocen de primera mano un entorno FabLab y un Living Lab, ejemplos de innovación educativa que sirven como escenarios perfectos para el desarrollo de ofertas formativas orientadas a la implementación de los ODS. Así, se demuestran la importancia de integrar los ODS en la educación superior y la relevancia de involucrar a los estudiantes en el proceso de aprendizaje activo en espacios comunes de trabajo que fomentan el sentido de autoeficacia y facilitan la adquisición y retención de conocimiento en el proceso educativo., [EN] Due to the strong relationship between the Sustainable Development Goals (SDGs) and the engineering world, this paper proposes a teaching activity focused on promoting the circular economy of the Higher Technical School of Industrial Engineers of the Polytechnic University of Madrid (ETSII-UPM) through the revaluation of plastic waste, which it was generated at the School. This revaluation consists of mechanical recycling to manufacture 3D filament using waste from defective printed parts that have been produced at the school. This activity is focused on a biobased and biodegradable plastic, poly(lactic acid) (PLA), for the generation of new products by 3D printing and, subsequently, corroborating its compostability. This represents a good demonstration of the full integration of the circular economy in a productive process. Students get to know first-hand a FabLab and Living Lab environment, which are examples of educational innovation that serve as a perfect frame for development training offers aimed at implementing the SDGs. Thus, the importance of integrating the SDGs in higher education, and the relevance of involving students in the active learning process in common workspaces, which foster a sense of self-efficacy and facilitate the acquisition and retention of knowledge in the educative process, are demonstrated., Este trabajo es parte de los proyectos de I+D+i PID2021-123753NA-C32 y TED2021-129920A-C43, financiado por MCIN/AEI/10.13039/501100011033 así como también por “FEDER Una manera de hacer Europa” y por la “Unión Europea NextGenerationEU/PRTR”, respectivamente. Ángel Agüero Rodríguez y Diego Lascano agradecen su contrato postdoctoral Margarita Salas con la Universitat Politècnica de València, financiado, a través del Ministerio de Universidades, por la Unión Europea-Next generation EU. Javiera Sepúlveda agradece al proyecto de la Universidad Politécnica de Madrid “SDGine for Healthy People and Cities” el cual ha recibido financiación del Programa de Investigación e Innovación Horizonte 2020 de la Unión Europea en el marco del acuerdo de subvención Marie Skłodowska-Curie No 945139 y de ECOEMBALAJES ESPAÑA, S.A. (Ecoembes). David Hidalgo-Carvajal agradece al proyecto WEDISTRICT financiado por el programa de investigación e innovación Horizon 2020 de la Unión Europea con acuerdo N°857801 y al proyecto de investigación “Campus UPM Circulares” de la Universidad Politécnica de Madrid. Finalmente, los autores recalcan que este trabajo es parte de la comunidad “The Circular and Regenerative Campus” perteneciente a la comunidad EELISA European University Alliance.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Optimization of the curing conditions of PVC plastisols plasticized with ethyl cinnamate

  • Gómez-Caturla, Jaume|||0000-0001-8680-4509
  • Quiles-Carrillo, Luis|||0000-0001-8037-2215
  • Garcia-Garcia, Daniel|||0000-0002-2520-0186
  • Miranda-Pinzon, M.
  • Arrieta, M. P.
[EN] The use of ethyl cinnamate, an ester of cinnamic acid present in many fruits and plants, as a bio-based plasticizer for polyvinyl chloride (PVC) plastisols has been investigated. Different temperatures (180, 190, and 200 °C) and curing times (8, 11.5, and 15 min) have been evaluated for PVC plasticized with 70 phr (parts by weight of plasticizer per one hundred weight parts of PVC resin) of ethyl cinnamate in order to optimize the curing conditions of the material, as these play a fundamental role in determining the final properties. Optimization of curing conditions has been carried out by analyzing the effect of temperature and curing time on the tensile mechanical properties, thermal stability, morphological, color changes, and migration tendency for the different plasticized materials. It has been observed that the optimal curing conditions for PVC plasticized with ethyl cinnamate are achieved at a curing temperature of 190 °C and a curing time of 11.5 min. Under these conditions, a material with high tensile strength, around 6.4 MPa, and a high elongation at break, close to 570 %, is obtained which is comparable or even superior to materials cured in the presence of other conventional plasticizers used in the PVC industry. Additionally, through field emission scanning electron microscopy (FESEM), it has been observed that for these conditions, the curing process is complete, resulting in the complete fusion of PVC microcrystals. A material with high cohesion and very low migration loss, around 2.4 %, is obtained. The effectiveness of these curing conditions has also been demonstrated using thermogravimetry. An increase in the PVC dehydrochlorination temperature has been observed due to optimum plasticizer absorption and gelation., This research is a part of the grant PID2023-152869OB-C22, funded by MCIN/AEI/10.13039/501100011033, the grant PID2021-123753NA-C32 funded by MCIN/AEI/10.13039/501100011033 and by the ERDF "A way of making Europe" through the "European Union NextGenerationEU/PRTR" and the grant TED2021-131762A-I00, funded by MCIN/AEI/10.13039/501100011033 and by the European Union "NextGenerationEU"/PRTR. Authors also thank Generalitat Valenciana-GVA for funding this research through the grant numbers AICO/2021/025 and CIGE/2021/094. D. Garcia-Garcia wants to thank the Generalitat Valenciana (Spain) for their financial support through the "BEST" mobility program (CIBEST/2021/94) . J. Gomez-Caturla wants to thank FPU20/01732 grant funded by MCIN/AEI/10.13039/501100011033 and by ESF Investing in your future. Microscopy services at UPV are acknowledged for their help in using and collecting FESEM images.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Biodegradable active packaging films reinforced with thyme waste nanoparticles

  • Sempere-Torregrosa, Jaume|||0000-0002-8742-0301
  • Samper, María-Dolores|||0000-0002-5102-8412
  • Arrieta, Marina Patricia
  • Dominici, F.
  • Debora Puglia, Debora Puglia
  • Torre, Luigi
[EN] This present work introduces a novel strategy combining nanoparticles from thymus vulgaris (nT) infusion waste, incorporated at 1 wt% and 3 wt%, with maleinized corn oil (MCO) as a natural plasticizer into PLA-PHB blend (75 wt% PLA, 25 wt% PHB) The materials were processed by micro-extrusion into films intended for sustainable and biodegradable active packaging applications. Nanoparticle formulation with 3 wt% showed high variation in tensile properties compared to MCO blend with 41% and 75% decrease in tensile strength and elongation at break respectively, otherwise both nanoparticles¿ formulations still exhibit increase on ductile reaching 74% and 49% for 1¿3 wt% on elongation at break compared with neat PLA. Plasticizer effect of MCO and interaction of nT nanoparticles with the blend was confirmed by calorimetric analysis, showing Tg 15% and 9% decrease for 1¿3 wt% respectively. Results of colour and UV characterization suggest that the films could interfere with light incidence while maintaining high transparency. During composting test, it was observed that the addition of nanoparticles delayed the degradation grade, although all samples were composted within 30 days. Furthermore, the nanoparticles improved the oxygen barrier properties of developed films, leading to a reduction of above 40% for both nanoparticles¿ formulations in OTR-e values. In addition, nanoparticles highly increased antioxidant activity with 67% and 75% for 1¿3 wt%, interesting findings to develop sustainable, biodegradable and active materials for food packaging applications., This research was supported by I+D+i PID2021-123753NA-C32 and PID2021-123753NA-C33 projects by MCIN/AEI/https://doi.org/10.13039/501100011033 and by FEDER A way of making Europe , as well as the TED2021-129920 A-C43 and CNS2022-136064 projects by MCIN/AEI/https://doi.org/10.13039/501100011033 and by Unión Europea NextGenerationEU/PRTR.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Innovative solutions and challenges to increase the use of poly(3-hydroxybutyrate) in food packaging and disposables

  • Garcia-Garcia, Daniel|||0000-0002-2520-0186
  • Quiles-Carrillo, Luis|||0000-0001-8037-2215
  • Balart, Rafael|||0000-0001-5670-7126
  • Torres-Giner, Sergio|||0000-0001-9071-9542
  • Arrieta, Marina P.
[EN] Poly(3-hydroxybutyrate) (PHB) has gain in recent years a huge interest in the food packaging field due to its renewable origin from waste as well as non-food crops, high mechanical strength, medium-to-high barrier performance, and inherent biodegradability in natural environments. Despite these advantages, PHB also shows a narrow processing window and high brittleness since this homopolyester shows low thermal stability and high crystallinity, limiting its industrial application. The present review provides an updated state of the art of the most relevant aspects in terms of processing and properties of PHB materials with a particular emphasis for their use in sustainable food packaging. It also describes the most potential strategies that can be applied to improve both the processability and mechanical properties of PHB, including the melt blending with green plasticizers and flexible biodegradable polymers as well as the development of more ductile co-polyesters. Finally, the waste management of the newly developed PHB-based articles is discussed, from their potential compostability to develop more biopolymers to more economically favored alternatives such as mechanical and chemical recycling technologies., This work was funded by the Spanish Ministry of Science and Innovation (MICINN, Spain), grant PID2021-123753NA-C32 funded by MCIN/AEI/10.13039/501100011033 and by "ERDF A way of making Europe", by the "European Union"; Comunidad de Madrid (Spain) by CIRCULAGROPLAST, a research Project that has been funded by the Comunidad de Madrid through the call Research Grants for Young Investigators from Universidad Politécnica de Madrid; as well as by the Generalitat Valenciana (Spain) through the BEST Program (CIBEST/2021/94). S. Torres-Giner acknowledges the Spanish Ministry of Science and Innovation (MICINN, Spain) for his Ramón y Cajal contract (RYC2019-027784-I).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Effect of Different Porous Size of Porous Inorganic Fillers on the Encapsulation of Rosemary Essential Oil for PLA-Based Active Packaging

  • Cerdá-Gandía, Raúl
  • Agüero, Ángel
  • Arrieta, Marina Patricia
  • Fenollar, Octavio|||0000-0003-4323-7414
[EN] Essential oils are interesting active additives for packaging manufacturing as they can provide the final material with active functionalities. However, they are frequently volatile compounds and can be degraded during plastic processing. In this work Rosmarinus officinalis (RO) essential oil was encapsulated into Diatomaceous earth (DE) microparticles and into Halloysite nanotubes (HNTs) and further used to produce eco-friendly active packaging based on polylactic acid (PLA). PLA-based composites and nanocoposites films based on PLA reinforced with DE + RO and HNTs + RO, respectively, were developed by melt extrusion followed by cast-film, simulating the industrial processing conditions. As these materials are intended as active food packaging films, the obtained materials were fully characterized in terms of their mechanical, thermal and structural properties, while migration of antioxidant RO was also assessed as well as the compostability at laboratory scale level. Both DE and HNTs were able to protect the Rosmarinus officinalis (RO) from thermal degradation during processing, allowing to obtain films with antioxidant properties as demonstrated by the antioxidant assays after the materials were exposed for 10 days to a fatty food simulant. The results showed that incorporating Rosmarinus officinalis encapsulated in either DE or HNTs and the good dispersion of such particles into the PLA matrix strengthened its mechanical performance and sped up the disintegration under composting conditions of PLA, while allowing to obtain films with antioxidant properties of interest as antioxidant active food packaging materials., This research was funded by the Spanish Ministry of Science and Innovation (MICINN) through PID-AEI project (grants PID2020-116496RB-C22 and PID2021-123753NA-C32) funded by MCIN/AEI/10.13039/501100011033 and by ERDF "A way of making Europe" by the "European Union" and TED-AEI Project (grant TED2021-129920A-C43) and Research Consolidator Project (grant CNS2022-136064) funded by MCIN/AEI/10.13039/501100011033 and by the "European Union NextGenerationEU/PRTR". Angel Agueero acknowledges the Margarita Salas postdoctoral grant from the Ministerio de Universidades, Spain, funded by the European Union-Next Generation EU.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Use of bacterial cellulose obtained from kombucha fermentation in spent coffee grounds for active composites based on PLA and maleinized linseed oil

  • Agüero, Ángel
  • Arrieta, Marina P.
  • Lascano-Aimacaña, Diego Sebastián|||0000-0002-0996-1946
  • Ivorra-Martinez, Juan|||0000-0001-8968-4899
  • Gómez-Caturla, Jaume|||0000-0001-8680-4509
  • Balart, Rafael|||0000-0001-5670-7126
[EN] Spent coffee grounds have been successfully used as an alternative infusion for kombucha fermentation (spent coffee kombucha, SCK). The obtained by-product of this fermentation consists of a kombucha bacterial cellulose (KBC) matrix. The bacterial cellulose was also fermented in pristine coffee grounds infusion for comparison (coffee kombucha, CK). The bacterial cellulose obtained from both infusion fermentations (SCK and CK) was used as filler in PLA matrix plasticized with a 5 wt% of maleinized linseed oil (MLO). Two different content of SCK and CK (3 and 5 wt%) were introduced in the PLA-MLO matrix to produce a film using a conical twin-screw microextruder to simulate the industrial processing conditions. The resultant bio-based films were studied in tern of morphological, tensile, and thermal properties, UV¿visible absorption, water vapor permeability, and wettability. The antioxidant activity of the obtained materials was tested in contact with a fatty food simulant demonstrating antioxidant activity. In addition, disintegrability tests under composting conditions confirmed the compostable character of all films. The obtained results suggest the potential applicability of these bio-based materials obtained by the revaluation of HoReCa waste in antioxidant materials with interest as food packaging or for agricultural uses., This research contributes to "The Circular and Regenerative Campus" community from the EELISA European University Alliance. Authors gratefully acknowledge Alcoin for kindly providing the coffee waste recovered at the University canteen of the Industrial Engineering School of the Polytechnic University of Madrid (ETSII-UPM). This research was funded by the Spanish Ministry of Science and Innovation (MICINN) through PID-AEI project (grants PID2020-116496RB-C22 and PID2021-123753NA-C32) funded by MCIN/AEI/10.13039/501100011033 and by ERDF "A way of making Europe" by the "Euro-pean Union" and TED-AEI Projects (grants TED2021-129920A-C43 and TED2021-131762A-I00) and "Consolidaci'on Investigadora" Project (grant CNS2022-136064 funded by MCIN/AEI/10.13039/501100011033 and by the "European Union NextGenerationEU/PRTR". It was also funded by Comunidad de Madrid-CAM ("Ayudas de Estimulo a la Investigaci'on de J'ovenes Doctores de la Universidad Polite'cnica de Madrid", APOYO-JOVENES-21-VUI9G6-56-I7GABQ) and Generalitat Valenciana-GVA grant numbers AICO/2021/025 and CIGE/2021/094. J. Gomez-Caturla wants to thank grant FPU20/01732 funded by MCIN/AEI/10.13039/501100011033 and by ESF Investing in your future. J. Ivorra-Martinez wants to thank FPU19/01759 grant funded by MCIN/AEI/10.13039/501100011033 and by ESF Investing in your future. Meanwhile, Ph.D. 'A. Agueero and Ph.D. D. Lascano acknowledge the Margarita Salas postdoctoral grants from the Ministerio de Uni-versidades, Spain, funded by the European Union-Next Generation EU.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Effect of processing temperature profile during melt extrusion on thermoplastic starch production

  • Aldas, Miguel
  • Arrieta, Marina P.
  • Pavón-Vargas, Cristina Paola|||0000-0003-2902-0059
  • Rosa-Ramírez, Harrison de la|||0000-0002-2913-7938
  • López-Martínez, Juan|||0000-0001-6904-2282
[EN] This work aims to evaluate the influence of the processing temperature on thermoplastic starch (TPS) for scalable production at the industrial level. Thus, it analyses the impact of six different extruding temperature profiles to plasticize native starch with water as well as with glycerol to obtain thermoplastic starch (TPS) produced by melt-extrusion. The temperature profiles ranged from 70 to 150 degrees C. At temperature profiles below 100 degrees C, the extrusion conditions were insufficient to disrupt the starch granules completely. Therefore, the material did not plasticize correctly, and the starchy matrix plasticizes partially using a temperature profile of 100 degrees C. The water evaporation process affects the final material's microstructure. At temperature profiles above 100 degrees C (i.e., 110 and 130 degrees C), the extrusion conditions allowed the disruption of the starch granule as well as a good material plasticization to obtain TPS. Although TPS obtained with a temperature profile of 150 degrees C displayed the highest mechanical properties, the material shows signs of thermal degradation under these conditions. Therefore, TPS processed at a profile with a maximum temperature of 130 degrees C showed a higher plasticization effect, good thermal and mechanical properties, and good water uptake capability. With its potential for successful industrial production, TPS can be obtained by processing native starch with water and glycerol at low share rates of 20 rpm and using 130 degrees C as a maximum processing temperature, offering a range of benefits., This research was funded by the Spanish Ministry of Science and Innovation (MCIN) through grants: PID2023-152869OB-C22 funded by MCIN/AEI/10.13039/501100011033 and the European Union Next-GenerationEU/PRTR as well as PID2021-123753NA-C32 funded by MCIN/AEI/10.13039/501100011033 and by ERDF A way of making Europe.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Biodegradable nanocomposite poly(lacticacid) foams containing carvacrol-based cocrystal prepared by supercritical CO2 processing for controlled release in active food packaging

  • Faba, Simón
  • Arrieta, Marina P.
  • Romero, Julio
  • Agüero, Ángel
  • Torres, Alejandra
  • Martínez, Sara
  • Galotto, María José
  • E. Rayón|||0000-0002-0653-2046
[EN] Compounds derived from essential oils have been used in active packaging, but their volatility and degradability negatively affect stability and leads to high release rates. The present study aimed to develop PLA bionanocomposite foams loaded with carvacrol cocrystal by supercritical CO2 and its release into a food simulant for control release in food packaging. For this purpose, 4,4'-bipyridine was used as coformer and carvacrol as active agent. Cocrystallized closed cell foams were obtained using supercritical CO2 and were characterized in terms of their physicochemical and mechanical properties, and release kinetics to a D1 simulant were evaluated as well as the antioxidant ability. A better overall mechanical behavior due to the nanoclay promoting a higher interfacial adhesion with the polymeric matrix was revealed. A higher incorporation of carvacrol was observed in samples with higher C30B content. The incorporated cocrystals showed a decrease of one order of magnitude in the estimated effective diffusion coefficient of carvacrol and showed antioxidant activity. These results suggest that the nanocomposite foam containing carvacrolbased cocrystals could be used in active packaging systems with controlled release characteristics, especially with highly volatile compounds, and can be proposed for other fields such as biomedical applications., This work has been developed in the framework of the project FONDECYT (grant number 12011301), Ph.D. Simon Faba is gratefully acknowledged to the National Commission for Scientific and Technological Research, ANID, for its financial support from the National Doctoral Scholarship (grant number 21200851) . Authors thank the financial support of CEDENNA (AFB 220001 Project) and the Spanish Ministry of Science and Innovation (MICINN) through the PID-AEI project (grant PID2021-123753NA-C32) funded by MCIN/AEI/10.13039/501100011033 and by ERDF "A way of making Europe" by the "European Union". Moreover, authors thank the staff of the Laboratory of Membrane Separation Processes (LabProSeM) , USACH, Santiago (Chile) for their assistance with equipment and CO2 supercritical system. Ph.D. Angel Agueero acknowledges the Margarita Salas post-doctoral grant from the Ministerio de Universidades, Spain, funded by the European Union-Next Generation EU. Marina P. Arrieta thanks "Consolidacion Investigadora" project (grant CNS2022-136064) funded by MCIN/AEI/10.13039/501100011033 and by the "European Union NextGenerationEU/PRTR".
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Plasticized Mechanical Recycled PLA Films Reinforced with Microbial Cellulose Particles Obtained from Kombucha Fermented in Yerba Mate Waste

  • Agüero, Ángel
  • Corral Perianes, Esther
  • Abarca de las Muelas, Sara Soledad
  • García-Soto, María del Mar de la Fuente
  • Peltzer, Mercedes Ana
  • Arrieta, Marina Patricia
  • Lascano-Aimacaña, Diego Sebastián|||0000-0002-0996-1946
  • Balart, Rafael|||0000-0001-5670-7126
[EN] In this study, yerba mate waste (YMW) was used to produce a kombucha beverage, and the obtained microbial cellulose produced as a byproduct (KMW) was used to reinforce a mechanically recycled poly(lactic acid) (r¿PLA) matrix. Microbial cellulosic particles were also produced in pristine yerba mate for comparison (KMN). To simulate the revalorization of the industrial PLA products rejected during the production line, PLA was subjected to three extrusion cycles, and the resultant pellets (r3¿PLA) were then plasticized with 15 wt.% of acetyl tributyl citrate ester (ATBC) to obtain optically transparent and flexible films by the solvent casting method. The plasticized r3¿PLA¿ATBC matrix was then loaded with KMW and KMN in 1 and 3 wt.%. The use of plasticizer allowed a good dispersion of microbial cellulose particles into the r3¿PLA matrix, allowing us to obtain flexible and transparent films which showed good structural and mechanical performance. Additionally, the obtained films showed antioxidant properties, as was proven by release analyses conducted in direct contact with a fatty food simulant. The results suggest the potential interest of these recycled and biobased materials, which are obtained from the revalorization of food waste, for their industrial application in food packaging and agricultural films., This research was funded by the Spanish Ministry of Science and Innovation (MICINN) through PID‐AEI project (grants PID2020‐116496RB‐C22 and PID2021‐123753NA‐C32) and TED‐ AEI project (grants TED2021‐129920A‐C43 and TED2021‐131762A‐I00) funded by MCIN/AEI/10.13039/501100011033 and by ERDF A way of making Europe by the European Union . It was also funded by Comunidad de Madrid‐CAM ( Ayudas de Estímulo a la Investigación de Jóvenes Doctores de la Universidad Politécnica de Madrid , APOYO‐JOVENES‐21‐VUI9G6‐56‐ I7GABQ), Generalitat Valenciana‐GVA grant numbers AICO/2021/025 and CIGE/2021/094 and National University of Quilmes (UNQ, Argentina) through the R&D program (Expediente 1300/19). Ph.D. Ángel Agüero and Ph.D. Diego Lascano acknowledge the Margarita Salas postdoctoral grants from the Ministerio de Universidades, Spain, funded by the European Union Next Generation EU.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Bio-Based and Biodegradable Polymeric Materials for a Circular Economy

  • Oliver-Cuenca, Víctor
  • Salaris, Valentina
  • Muñoz Gimena, Pedro Francisco
  • Agüero, Ángel
  • Peltzer, M.
  • Montero, Victoria Alcázar
  • Arrieta, Marina P.
  • Sempere-Torregrosa, Jaume
  • Pavon, Cristina
  • Samper, M. D.
  • Rodríguez Crespo, Gema
  • Kenny, José María
  • López, Daniel
  • Peponi, Laura
Nowadays, plastic contamination worldwide is a concerning reality that can be addressed with appropriate society education as well as looking for innovative polymeric alternatives based on the reuse of waste and recycling with a circular economy point of view, thus taking into consideration that a future world without plastic is quite impossible to conceive. In this regard, in this review, we focus on sustainable polymeric materials, biodegradable and bio-based polymers, additives, and micro/nanoparticles to be used to obtain new environmentally friendly polymeric-based materials. Although biodegradable polymers possess poorer overall properties than traditional ones, they have gained a huge interest in many industrial sectors due to their inherent biodegradability in natural environments. Therefore, several strategies have been proposed to improve their properties and extend their industrial applications. Blending strategies, as well as the development of composites and nanocomposites, have shown promising perspectives for improving their performances, emphasizing biopolymeric blend formulations and bio-based micro and nanoparticles to produce fully sustainable polymeric-based materials. The Review also summarizes recent developments in polymeric blends, composites, and nanocomposite plasticization, with a particular focus on naturally derived plasticizers and their chemical modifications to increase their compatibility with the polymeric matrices. The current state of the art of the most important bio-based and biodegradable polymers is also reviewed, mainly focusing on their synthesis and processing methods scalable to the industrial sector, such as melt and solution blending approaches like melt-extrusion, injection molding, film forming as well as solution electrospinning, among others, without neglecting their degradation processes., This research was funded by the Agencia Estatal de Investigación (AEI, MICINN, Spain), and Fondo Europeo de Desarrollo Regional (FEDER, EU), PID2021-123753NB-C31, PID2021-123753NA-C32, PID2021-123753NA-C33, and NextGenerationEU MRR TED2021-129335B-C21. V.O.-C. acknowledges Spanish government for the grant PRE2020-103097 funded by MCIN/AEI/10.13039/501100011033 and “ESF Investing in your future”. The authors want to know MICIN for PID2021-123753NB-C31 and TED2021-129335B-C21 projects and for RED2022-134806-T., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Plasticized Starch/Gelatin Blends with Humidity-Activated Shape-Memory Behavior

  • Oliver Cuenca, Víctor
  • Muñoz Menzinger, Ana
  • Arrieta, Marina P.
  • López, Daniel
  • Peponi, Laura
Biodegradable and bio-based polymers, such as starch and gelatin, are emerging as an important alternative to the use of conventional polymers. In this work, different proportions (1/1, 1/1.5, 1/2, and 1/2.5) of these bio-based polymers will be investigated, with the primary objective of considering their strong moisture dependence as an advantage instead of a problem, as commonly considered. For this interesting challenge, the humidity-activated shape memory effect has been studied in both neat and plasticized starch. Additionally, for the first time, to the best of our knowledge, the shape-memory behavior activated by humidity in gelatin, as well as in starch/gelatin blends, is reported. In all cases, starch, gelatin, and their plasticized blends show excellent values in terms of strain fixity ratio, obtaining values of about 100% in all cases, and strain recovery ratio, with values higher than 90% for the samples studied. Moreover, considering their potential application as food packaging, mechanical response, wettability, water permeability, water uptake rate, and roughness is also studied in this work, taking into account the effect of the different amounts of gelatin on the final behavior of the materials., This research was funded by the Agencia Estatal de Investigación (AEI, MICINN, Spain) and Fondo Europeo de Desarrollo Regional (FEDER, EU), PID2021-123753NB-C31, PID2021-123753NA-C32, TED2021-129335B-C21 projects, PRE2020-103097 and JAEINT_24_02566., Peer reviewed
e-cienciaDatos, Repositorio de Datos del Consorcio Madroño
Datos de investigación Set de datos (Dataset)

Mechanically Recycled PLA - MLO formulations

  • Beltrán, Freddys
  • Dominici, Franco
  • Agüero Rodriguez, Ángel
  • Lascano Aimacaña, Diego Sebastián
  • Arrieta, Marina Patricia
  • Balart, Rafael
  • PUGLIA, DEBORA
<p></p> <p>INFORMACIÓN GENERAL</p> <p></p> <p>3. Descripción del proyecto</p> <p>Estudio del reciclado mecánico de bandejas de PLA de post-consumo con aceite maleinizado de linaza como aditivo plastificante.</p> <p></p> <p>4. Descripción del dataset</p> <p>Datos experimentales obtenidos de la investigación del reciclado mecánico de PLA</p> <p></p> <p>METODOLOGÍA</p> <p></p> <p>1. Metodología (empleada para la recogida o generación de los datos)</p> <p>Los datos fueron obtenidos mediante diferentes técnicas experimentales incluyendo viscosimetría, calorimetría diferencial de barrido (DSC), análisis termogravimétrico (TGA), espectroscopía UV-Visible, espectroscopia FTIR, Resonancia Magnética Nuclear (1H-RMN), microscopía electrónica de barrido (SEM), microscopía de fuerza atómica (AFM), ensayos de tracción, ensayos de ángulo de contacto.</p> <p></p> <p>2. Software</p> <p>Archivos .tif: Fotografías SEM obtenidas mediante el software ZEISS SmartSEM.</p> <p>Archivos .jpg: Fotografías AFM obtenidas mediante el software NanoScope Analysis 2.0.</p> <p>Archivos .xlsx: Microsoft Excel</p> <p>Archivos .opj: OriginPro 9</p> <p></p> <p>FICHEROS</p> <p></p> <p>1. Ficheros (Relación de todos los ficheros que se incluyen en el dataset, estructura breve descripción de su contenido, indicar formato, idioma, versión, etc.)</p> <p></p> <p>Archivos .jpg (New-PLA, rPLA, rPLA1MLO, etc.): Fotografías AFM de las muestras</p> <p>Archivos .tif (1MLO_01, 1MLO_02, etc.): Fotografías SEM de las muestras</p> <p>Roughness.xlsx: Archivo con los valores de rugosidad de las diferentes muestras</p> <p>Contact_Angle.xlsx: Archivo con los resultados de ángulo de contacto</p> <p>Characteristic_Values_Tensile.xlsx: Archivo con los resultados de los ensayos de tracción</p> <p>DSC_Data.opj: Archivo con los datos de calorimetría diferencial de barrido.</p> <p>MFR and Thickness.xlsx: Archivo con espesores y valores de índice de fluidez</p> <p>FTIR_UPM.opj: Archivo con los datos de espectroscopía FTIR.</p> <p>SEM.zip: Carpeta con fotografías SEM de las muestras</p> <p>TGA_Data.opj: Archivo con los datos de análisis termogravimétrico</p> <p>UV-Vis.opj: Archivo con los datos de espectroscopía UV-Vis</p> <p>Viscosity.opj: Archivos con datos de viscosidad intrínseca</p>