Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 14
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Control of Biodegradability Under Composting Conditions and Physical Performance of Poly (Lactic Acid) Based Materials Modified with Phenolic-Free Rosin Resin

  • Rosa-Ramírez, Harrison de la|||0000-0002-2913-7938
  • Ferri, J.M|||0000-0002-1269-4973
  • López-Martínez, Juan|||0000-0001-6904-2282
  • Samper, María-Dolores|||0000-0002-5102-8412
  • Aldas, Miguel
  • Pawlak, Franciszek
[EN] Biodegradable materials based on poly (lactic acid) (PLA) and a phenolic free modified rosin resin were obtained and studied to control the biodegradability under composting conditions of the materials. The resin was blended in concentrations of 1, 3, 5, 10, and 15 parts per hundred (phr) of base polymer using industrial plastic processing techniques. Additionally, to study the effect of the resin on the compatibility of the PLA, the physical performance, water absorption, mechanical behavior, thermal stability, and microstructure of the materials were assessed. The resin incorporation decreased the resistance to thermal degradation of the resultant material, and the composting disintegration rate was slowed down with the increasing content of the resin. The water diffusion was delayed, and the diffusion and corrected diffusion coefficients decreased with the rising content of UP. The mechanical properties tend to decrease while a saturation effect was observed for contents higher than 3 phr of resin. The optimal amount of resin that can be added to achieve good interaction with PLA matrix, complete miscibility, and good material cohesion is 3 phr., Open Access funding provided thanks to the CRUE-CSIC agreement with Springer Nature. This research was funded by MCIN/AEI/10.13039/501100011033 through PID-AEI Project (grant PID2021-123753NA-C33 and PID2020-116496RB-C22) and TED-AEI Project (grants TED2021-129920A-C43), and, as appropriate, by "ERDF A way of making Europe", by the "European Union" or by the "European Union NextGenerationEU/PRTR.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Pentaerythritol and Glycerol Esters Derived from Gum Rosin as Bio-Based Additives for the Improvement of Processability and Thermal Stability of Polylactic Acid

  • Rosa-Ramírez, Harrison de la|||0000-0002-2913-7938
  • Ferri, J.M|||0000-0002-1269-4973
  • López-Martínez, Juan|||0000-0001-6904-2282
  • Samper, María-Dolores|||0000-0002-5102-8412
  • Dominici, Franco
  • Luzi, Francesca
  • Puglia, Debora
  • Torre, Luigi
[EN] Gum rosin esters are some of the most common gum rosin derivatives used in different applications, such as coatings, paper, varnishes, chewing gum, and food industries. In this study, gum rosin esters are used as additives for polylactic acid (PLA) to improve its processability and thermal stability. Blends of an amorphous PLA with two different gum rosin esters, pentaerythritol ester and glycerol ester, were prepared by melt extrusion process in concentrations from 1, 3, and 5 phr. Besides the comparison of thermal degradation, microstructure assessment, and melt flow index (MFI) analysis, the processability performance during testing samples production by injection molding process was evaluated. Experimental results showed that MFI values of PLA-gum rosin ester blends increased by 100%, 147%, and 164%, along with increasing content of gum rosin esters addition, in both cases. Also, both derivatives slightly improved PLA thermal stability (around 3ºC higher). Injection molding temperature decreased by at least 20 °C for PLA-gum rosin ester blends compared with neat PLA. Furthermore, the maximum tensile strength of PLA-gum rosin esters was negligibly affected in formulations with low content of gum rosin esters, and the FESEM images revealed a good dispersion and compatibility of gum rosin ester particles into PLA matrix in both concentrations., This research was funded by MCIN/AEI/10.13039/501100011033 through PID-AEI Project (grant PID2021-123753NA-C33 and PID2020-116496RB-C22) and TED-AEI Project (grants TED2021-129920 A-C43), and, as appropriate, by "ERDF A way of making Europe", by the "European Union" or by the "European Union NextGenerationEU/PRTR".Open Access funding provided thanks to the CRUE-CSIC agreement with Springer Nature.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Nanoparticles From Infusion Beverage Wastes and Their Effect on PLA/PHB Plasticized Composite Behavior

  • Sempere-Torregrosa, Jaume|||0000-0002-8742-0301
  • Rosa-Ramírez, Harrison de la|||0000-0002-2913-7938
  • Samper, María-Dolores|||0000-0002-5102-8412
  • Dominici, Franco
  • Puglia, Debora
  • Torre, Luigi
[EN] In this work, yerba mate (nYM) and black tea (nBT) nanoparticles were extracted from Ilex paraguariensis and Camellia sinensis, respectively. Unlike traditional biocomposites and additives, this approach valorizes the waste of infusion beverages without using chemical compounds. Nanoparticles underwent preliminary TGA analysis, showing stable and high degradation temperature, making them suitable for processing with the selected polymer matrix. Subsequently, they were incorporated into the selected PLA (75%)-PHB (25%) blend plasticized with maleinized corn oil (MCO) at a concentration of 1-3 wt.%. Tensile characterization of the PLA-PHB blend plasticized with MCO showed an improvement in compatibility between polymers, with increased ductility. The plasticizing effect of MCO was confirmed by calorimetric analysis, showing a remarkable decrease in Tg value. The combination of MCO and nanoparticles continues to exhibit enhanced thermal stability, showing functional nanofiller behavior. Moreover, the presence of nanoparticles enhanced the barrier property of the plasticized films toward oxygen barrier properties, reducing the OTR-e values. Finally, during the second half of the composting test, it was observed that nanoparticle addition delayed the degradation process; otherwise, it continued showing interesting biodegradable properties. These findings open multiple possibilities in the combined use of infusion beverage waste nanoparticles and modified vegetable oils to develop sustainable packaging applications., This research was funded by MCIN/AEI/10.13039/501100011033 through the PID-AEI Project (grant PID2021-123753NA-C33) and the TED- AEI Project (grant TED2021-129920A-C43) and, as appropriate, by "ERDF A way of making Europe", by the "European Union" or by the "European Union NextGenerationEU/PRTR". M.D. Samper thanks the Spanish Ministerio de Ciencia, Innovacin y Universidades for the funding received for the Jose Castillejo mobility stay (grant CAS21/00379).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Foaming of 3D-Printed PLA/CaCO3 Composites by Supercritical CO2 Process for Sustainable Food Contact Materials

  • Faba, Simón
  • Agüero, Ángel
  • Arrieta, Marina P.
  • Martínez, Sara
  • Romero, Julio
  • Torres, Alejandra
  • Galotto, María José
[EN] In the last decade, among the emerging technologies in the area of bioplastics, additive manufacturing (AM), commonly referred to as 3D printing, stands out. This technology has gained great interest in the development of new products, mainly due to its capability to easily produce customized and low-cost plastic products. This work aims to evaluate the effect of supercritical foaming of 3D-printed parts based on a commercial PLA matrix loaded with calcium carbonate, for single-use sustainable food contact materials. 3D-printed PLA/CaCO3 parts were obtained by 3D printing with a 20% and 80% infill, and two infill patterns, rectilinear and triangular, were set for each of the infill percentages selected. Supercritical fluid foaming of PLA/CaCO3 composite printed parts was performed using a pressure of 25 MPa, a temperature of 130 degrees C for 23 min, with a fast depressurization rate (1 s). Closed-cell foams were achieved and the presence of CaCO3 did not influence the surface of the foams or the cell walls, and no agglomerations were observed. Foam samples with 80% infill showed subtle temperature fluctuations, and thermogravimetric analysis showed that samples were thermally stable up to similar to 300 degrees C, while the maximum degradation temperature was around 365 degrees C. Finally, tensile test analysis showed that for lower infill contents, the foams showed lower mechanical performance, while the 80% infill and triangular pattern produced foams with good mechanical performance. These results emphasize the interest in using the supercritical CO2 process to easily produce foams from 3D-printed parts. These materials represent a sustainable alternative for replacing non-biodegradable materials such as Expanded Polystyrene, and they are a promising option for use in many industrial applications, such as contact materials., Simón Faba gratefully acknowledges the National Commission for Scientific and Technological Research, ANID, for its financial support from the Postdoctoral Scholarship abroad (grant number 74230053). Authors thank the financial support of CEDENNA (AFB 220001 Project) and the Spanish Ministry of Science and Innovation (MICINN) through the PID-AEI project (grant PID2021-123753NA-C32) funded by MCIN/AEI/10.13039/501100011033 and by ERDF A way of making Europe by the European Union as well as the TED-AEI project (grant TED-129920A-C43) and Research consolidation project (grant CNS2022-136064) funded by MCIN/AEI/10.13039/501100011033 and by the European Union NextGenerationEU/PRTR . Ángel Agüero acknowledges the Margarita Salas post-doctoral grant from the Ministerio de Universidades, Spain, funded by the Recovery, Transformation, and Resilience Plan financed by the European Union NextGenerationEU. The co-financing of the project FONDECYT-ANID (grant number 1230795) is also acknowledged.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Thermal and Mechanical Performance of Maleic Anhidride/Benzoyl Peroxide-Modified PLA/PCL Biocomposites

  • Unamuno-Garay, Aritz
  • Llidó Barragán, Alexandra|||0009-0006-4847-8048
  • Ferrándiz Bou, Santiago|||0000-0001-7137-9298
  • Samper, María-Dolores|||0000-0002-5102-8412
[EN] This study investigated PLA/PCL blends modified with maleic anhydride (MA) via radical grafting using benzoyl peroxide (BPO) as an initiator. Different formulations with 5 and 10 wt.% of PLA-g-MA (containing 1, 3, and 5 wt.% MA) were prepared to evaluate their compatibilizing effect. Samples were characterized thermally, mechanically, and morphologically using DSC, TGA, FTIR, goniometry, SEM, and tensile, impact, and hardness tests. The results show that adding PCL significantly improves the ductility of PLA, though it reduces tensile strength and hardness. Grafting with MA partially improves phase compatibility, as seen by increased elongation at break and impact resistance, especially at intermediate MA concentrations (1¿3%). However, higher MA contents lead to greater variability in thermal and mechanical results, likely due to heterogeneous phase dispersion. FTIR analysis detected residual BPO in some formulations, though below 0.1 phr. TGA indicated a slight improvement in thermal stability at 5 wt.% MA. Overall, the findings suggest that controlled use of MA as a compatibilizer enhances the balance of mechanical and thermal properties in PLA/PCL systems., The authors acknowledge the I+D+i PID2021-123753NA-C33 project by MCIN/AEI/10.13039/ 501100011033 and by FEDER A way of making Europe , as well as the TED2021-129920A-C43 project by MCIN/AEI/10.13039/501100011033 and by Unión Europea NextGenerationEU/PRTR .
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Capítulo o parte de un libro (BookPart)

Introduciendo los ODS y la circularidad a la educación en ingeniería a través de actividades para el reciclado de plásticos en un campus universitario

  • Agüero Rodríguez, Ángel
  • Hidalgo-Carvajal, David
  • Lascano, Diego
  • Sepúlveda, Javiera
  • Arrieta, Marina Patricia
  • Carrasco-Gallego, Ruth
  • M. Muneta, María Luisa
[ES] Atendiendo a la vinculación directa de los objetivos de desarrollo sostenible (ODS) con el mundo ingenieril, en este trabajo se plantea una actividad docente centrada en fomentar la economía circular de la Escuela Técnica Superior de Ingenieros Industriales de la Universidad Politécnica de Madrid, mediante la revalorización de residuos plásticos generados en la Escuela mediante reciclado mecánico. La actividad consiste en la fabricación de filamento 3D empleando residuos de piezas impresas defectuosas que han sido fabricadas en la escuela utilizando un plástico biobasado y biodegradable, el poli(ácido láctico) (PLA), para la generación de nuevos productos por impresión 3D y, posteriormente, comprobar la compostabilidad de dichos productos demostrando que se integran completamente en la economía circular. Los estudiantes conocen de primera mano un entorno FabLab y un Living Lab, ejemplos de innovación educativa que sirven como escenarios perfectos para el desarrollo de ofertas formativas orientadas a la implementación de los ODS. Así, se demuestran la importancia de integrar los ODS en la educación superior y la relevancia de involucrar a los estudiantes en el proceso de aprendizaje activo en espacios comunes de trabajo que fomentan el sentido de autoeficacia y facilitan la adquisición y retención de conocimiento en el proceso educativo., [EN] Due to the strong relationship between the Sustainable Development Goals (SDGs) and the engineering world, this paper proposes a teaching activity focused on promoting the circular economy of the Higher Technical School of Industrial Engineers of the Polytechnic University of Madrid (ETSII-UPM) through the revaluation of plastic waste, which it was generated at the School. This revaluation consists of mechanical recycling to manufacture 3D filament using waste from defective printed parts that have been produced at the school. This activity is focused on a biobased and biodegradable plastic, poly(lactic acid) (PLA), for the generation of new products by 3D printing and, subsequently, corroborating its compostability. This represents a good demonstration of the full integration of the circular economy in a productive process. Students get to know first-hand a FabLab and Living Lab environment, which are examples of educational innovation that serve as a perfect frame for development training offers aimed at implementing the SDGs. Thus, the importance of integrating the SDGs in higher education, and the relevance of involving students in the active learning process in common workspaces, which foster a sense of self-efficacy and facilitate the acquisition and retention of knowledge in the educative process, are demonstrated., Este trabajo es parte de los proyectos de I+D+i PID2021-123753NA-C32 y TED2021-129920A-C43, financiado por MCIN/AEI/10.13039/501100011033 así como también por “FEDER Una manera de hacer Europa” y por la “Unión Europea NextGenerationEU/PRTR”, respectivamente. Ángel Agüero Rodríguez y Diego Lascano agradecen su contrato postdoctoral Margarita Salas con la Universitat Politècnica de València, financiado, a través del Ministerio de Universidades, por la Unión Europea-Next generation EU. Javiera Sepúlveda agradece al proyecto de la Universidad Politécnica de Madrid “SDGine for Healthy People and Cities” el cual ha recibido financiación del Programa de Investigación e Innovación Horizonte 2020 de la Unión Europea en el marco del acuerdo de subvención Marie Skłodowska-Curie No 945139 y de ECOEMBALAJES ESPAÑA, S.A. (Ecoembes). David Hidalgo-Carvajal agradece al proyecto WEDISTRICT financiado por el programa de investigación e innovación Horizon 2020 de la Unión Europea con acuerdo N°857801 y al proyecto de investigación “Campus UPM Circulares” de la Universidad Politécnica de Madrid. Finalmente, los autores recalcan que este trabajo es parte de la comunidad “The Circular and Regenerative Campus” perteneciente a la comunidad EELISA European University Alliance.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Epoxidized and Maleinized Hemp Oil to Develop Fully Bio-Based Epoxy Resin Based on Anhydride Hardeners

  • Lerma-Canto, Alejandro
  • Samper, María-Dolores|||0000-0002-5102-8412
  • Domínguez-Candela, Iván|||0000-0003-3288-1079
  • Garcia-Garcia, Daniel|||0000-0002-2520-0186
  • Fombuena, Vicent|||0000-0001-7266-6205
[EN] The present work aims to develop thermosetting resins using epoxidized hemp oil (EHO) as a bio-based epoxy matrix and a mixture of methyl nadic anhydride (MNA) and maleinized hemp oil (MHO) in different ratios as hardeners. The results show that the mixture with only MNA as a hardener is characterized by high stiffness and brittleness. In addition, this material is characterized by a high curing time of around 170 min. On the other hand, as the MHO content in the resin increases, the mechanical strength properties decrease and the ductile properties increase. Therefore, it can be stated that the presence of MHO confers flexible properties to the mixtures. In this case, it was determined that the thermosetting resin with balanced properties and high bio-based content contains 25% MHO and 75% MNA. Specifically, this mixture obtained a 180% higher impact energy absorption and a 195% lower Young's modulus than the sample with 100% MNA. Also, it has been observed that this mixture has significantly shorter times than the mixture containing 100% MNA (around 78 min), which is of great concern at an industrial level. Therefore, thermosetting resins with different mechanical and thermal properties can be obtained by varying the MHO and MNA content., This research was funded by MCIN/AEI/ 10.13039/501100011033 through the PID-AEI Project (grants PID2020-119142RA-I00 and PID2021-123753NA-C33) and the TED-AEI Project (grants TED2021-129920A-C43 and TED2021-131762A-100) and, as appropriate, by ¿ERDF A way of making Europe¿, by the ¿European Union¿ or by the ¿European Union NextGenerationEU/PRTR¿. Dominguez-Candela wants to thank Universitat Politècnica de València for his FPI grant (PAID-2019-SP20190013) and Generalitat Valenciana (GVA) for his FPI grant (ACIF/2020/233).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Biodegradable active packaging films reinforced with thyme waste nanoparticles

  • Sempere-Torregrosa, Jaume|||0000-0002-8742-0301
  • Samper, María-Dolores|||0000-0002-5102-8412
  • Arrieta, Marina Patricia
  • Dominici, F.
  • Debora Puglia, Debora Puglia
  • Torre, Luigi
[EN] This present work introduces a novel strategy combining nanoparticles from thymus vulgaris (nT) infusion waste, incorporated at 1 wt% and 3 wt%, with maleinized corn oil (MCO) as a natural plasticizer into PLA-PHB blend (75 wt% PLA, 25 wt% PHB) The materials were processed by micro-extrusion into films intended for sustainable and biodegradable active packaging applications. Nanoparticle formulation with 3 wt% showed high variation in tensile properties compared to MCO blend with 41% and 75% decrease in tensile strength and elongation at break respectively, otherwise both nanoparticles¿ formulations still exhibit increase on ductile reaching 74% and 49% for 1¿3 wt% on elongation at break compared with neat PLA. Plasticizer effect of MCO and interaction of nT nanoparticles with the blend was confirmed by calorimetric analysis, showing Tg 15% and 9% decrease for 1¿3 wt% respectively. Results of colour and UV characterization suggest that the films could interfere with light incidence while maintaining high transparency. During composting test, it was observed that the addition of nanoparticles delayed the degradation grade, although all samples were composted within 30 days. Furthermore, the nanoparticles improved the oxygen barrier properties of developed films, leading to a reduction of above 40% for both nanoparticles¿ formulations in OTR-e values. In addition, nanoparticles highly increased antioxidant activity with 67% and 75% for 1¿3 wt%, interesting findings to develop sustainable, biodegradable and active materials for food packaging applications., This research was supported by I+D+i PID2021-123753NA-C32 and PID2021-123753NA-C33 projects by MCIN/AEI/https://doi.org/10.13039/501100011033 and by FEDER A way of making Europe , as well as the TED2021-129920 A-C43 and CNS2022-136064 projects by MCIN/AEI/https://doi.org/10.13039/501100011033 and by Unión Europea NextGenerationEU/PRTR.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Effect of Different Porous Size of Porous Inorganic Fillers on the Encapsulation of Rosemary Essential Oil for PLA-Based Active Packaging

  • Cerdá-Gandía, Raúl
  • Agüero, Ángel
  • Arrieta, Marina Patricia
  • Fenollar, Octavio|||0000-0003-4323-7414
[EN] Essential oils are interesting active additives for packaging manufacturing as they can provide the final material with active functionalities. However, they are frequently volatile compounds and can be degraded during plastic processing. In this work Rosmarinus officinalis (RO) essential oil was encapsulated into Diatomaceous earth (DE) microparticles and into Halloysite nanotubes (HNTs) and further used to produce eco-friendly active packaging based on polylactic acid (PLA). PLA-based composites and nanocoposites films based on PLA reinforced with DE + RO and HNTs + RO, respectively, were developed by melt extrusion followed by cast-film, simulating the industrial processing conditions. As these materials are intended as active food packaging films, the obtained materials were fully characterized in terms of their mechanical, thermal and structural properties, while migration of antioxidant RO was also assessed as well as the compostability at laboratory scale level. Both DE and HNTs were able to protect the Rosmarinus officinalis (RO) from thermal degradation during processing, allowing to obtain films with antioxidant properties as demonstrated by the antioxidant assays after the materials were exposed for 10 days to a fatty food simulant. The results showed that incorporating Rosmarinus officinalis encapsulated in either DE or HNTs and the good dispersion of such particles into the PLA matrix strengthened its mechanical performance and sped up the disintegration under composting conditions of PLA, while allowing to obtain films with antioxidant properties of interest as antioxidant active food packaging materials., This research was funded by the Spanish Ministry of Science and Innovation (MICINN) through PID-AEI project (grants PID2020-116496RB-C22 and PID2021-123753NA-C32) funded by MCIN/AEI/10.13039/501100011033 and by ERDF "A way of making Europe" by the "European Union" and TED-AEI Project (grant TED2021-129920A-C43) and Research Consolidator Project (grant CNS2022-136064) funded by MCIN/AEI/10.13039/501100011033 and by the "European Union NextGenerationEU/PRTR". Angel Agueero acknowledges the Margarita Salas postdoctoral grant from the Ministerio de Universidades, Spain, funded by the European Union-Next Generation EU.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Polybutylene succinate film incorporating essential oil as active packaging materials to prolong tomatoes shelf-life

  • Barrino, Federico
  • Finamore, Rosario
  • Mirpoor, Seyedeh Fatemeh
  • Schiraldi, Chiara
  • Rosa-Ramírez, Harrison de la|||0000-0002-2913-7938
  • Sempere-Torregrosa, Jaume|||0000-0002-8742-0301
  • López-Martínez, Juan|||0000-0001-6904-2282
  • Samper, María-Dolores|||0000-0002-5102-8412
[EN] The present research work deals with the laboratory scale manufacturing of thin films based on polybutylene succinate (PBS), a sustainably obtained biodegradable polyester (bioplastic), with the aim to propose their use in food packaging in order to slow down the food degradation process, to replace the polymers derived from fossil fuels. To this purpose, thin films of (PBS) were prepared by adding diverse Mediterranean herbs extracts up to 3 % by weight. Specifically, PBS was added with three different types of natural oils/extracts: thymol, carvacrol, and basil extract (mainly rich in eugenol). These compounds, well known for their antioxidant and antimicrobial potential, conferred functional activity to the films. The resulting materials were characterized in terms of chemical, thermal, optical, mechanical, and gas permeability properties, as well as antioxidant activity and preliminary food-contact tests. Tomatoes wrapped in the active films showed delayed oxidative browning and reduced microbial spoilage during three weeks of storage. Among the various formulations, the blend containing all essential oils (PBS/All) offered the best compromise between thermal stability, structural compactness, and preservation capacity. These results suggest that PBS/All films are promising candidates for sustainable active packaging applications., This research was partially funded by MCIN/AEI/10.13039/501100011033 through the PID-AEI Project (grant PID2021-123753NA-C33) , Project (grant PID2024-157368NB-C33) and the TED-AEI Project (grant TED2021-129920A-C43) and, as appropriate, by "ERDF A way of making Europe", by the "European Union" or by the "European Union NextGenerationEU/PRTR". This research was partially funded by Bionutra Project (Italian Ministry of Research) .
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Use of bacterial cellulose obtained from kombucha fermentation in spent coffee grounds for active composites based on PLA and maleinized linseed oil

  • Agüero, Ángel
  • Arrieta, Marina P.
  • Lascano-Aimacaña, Diego Sebastián|||0000-0002-0996-1946
  • Ivorra-Martinez, Juan|||0000-0001-8968-4899
  • Gómez-Caturla, Jaume|||0000-0001-8680-4509
  • Balart, Rafael|||0000-0001-5670-7126
[EN] Spent coffee grounds have been successfully used as an alternative infusion for kombucha fermentation (spent coffee kombucha, SCK). The obtained by-product of this fermentation consists of a kombucha bacterial cellulose (KBC) matrix. The bacterial cellulose was also fermented in pristine coffee grounds infusion for comparison (coffee kombucha, CK). The bacterial cellulose obtained from both infusion fermentations (SCK and CK) was used as filler in PLA matrix plasticized with a 5 wt% of maleinized linseed oil (MLO). Two different content of SCK and CK (3 and 5 wt%) were introduced in the PLA-MLO matrix to produce a film using a conical twin-screw microextruder to simulate the industrial processing conditions. The resultant bio-based films were studied in tern of morphological, tensile, and thermal properties, UV¿visible absorption, water vapor permeability, and wettability. The antioxidant activity of the obtained materials was tested in contact with a fatty food simulant demonstrating antioxidant activity. In addition, disintegrability tests under composting conditions confirmed the compostable character of all films. The obtained results suggest the potential applicability of these bio-based materials obtained by the revaluation of HoReCa waste in antioxidant materials with interest as food packaging or for agricultural uses., This research contributes to "The Circular and Regenerative Campus" community from the EELISA European University Alliance. Authors gratefully acknowledge Alcoin for kindly providing the coffee waste recovered at the University canteen of the Industrial Engineering School of the Polytechnic University of Madrid (ETSII-UPM). This research was funded by the Spanish Ministry of Science and Innovation (MICINN) through PID-AEI project (grants PID2020-116496RB-C22 and PID2021-123753NA-C32) funded by MCIN/AEI/10.13039/501100011033 and by ERDF "A way of making Europe" by the "Euro-pean Union" and TED-AEI Projects (grants TED2021-129920A-C43 and TED2021-131762A-I00) and "Consolidaci'on Investigadora" Project (grant CNS2022-136064 funded by MCIN/AEI/10.13039/501100011033 and by the "European Union NextGenerationEU/PRTR". It was also funded by Comunidad de Madrid-CAM ("Ayudas de Estimulo a la Investigaci'on de J'ovenes Doctores de la Universidad Polite'cnica de Madrid", APOYO-JOVENES-21-VUI9G6-56-I7GABQ) and Generalitat Valenciana-GVA grant numbers AICO/2021/025 and CIGE/2021/094. J. Gomez-Caturla wants to thank grant FPU20/01732 funded by MCIN/AEI/10.13039/501100011033 and by ESF Investing in your future. J. Ivorra-Martinez wants to thank FPU19/01759 grant funded by MCIN/AEI/10.13039/501100011033 and by ESF Investing in your future. Meanwhile, Ph.D. 'A. Agueero and Ph.D. D. Lascano acknowledge the Margarita Salas postdoctoral grants from the Ministerio de Uni-versidades, Spain, funded by the European Union-Next Generation EU.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Material Performance and Processing Behavior of Polyolefin Waste in Mechanical Recycling

  • Vazquez, Yamila V.
  • Miguel Guillem, Juan Vicente
  • Pavón-Vargas, Cristina Paola|||0000-0003-2902-0059
  • López-Martínez, Juan|||0000-0001-6904-2282
  • Samper, María-Dolores|||0000-0002-5102-8412
[EN] This study investigates the processability and performance limits of high-density polyethylene (HDPE) recovered from mixed polyolefin waste under realistic mechanical recycling conditions. The waste stream was processed by extrusion and injection molding, with parameters actively adapted. ATR-FTIR and DSC analysis confirmed HDPE as the matrix, contaminated with minor fractions of polypropylene (PP), PET, and polyurethane (PU). The reprocessed material exhibited a single melting peak at 132 degrees C and a melt flow rate (MFR) of 9.9 +/- 0.6 g 10 min-1, indicative of moderate degradation. Mechanical testing revealed reduced tensile strength and elongation at break compared to virgin HDPE, indicating compositional heterogeneity and poor interfacial adhesion. Field emission scanning electron microscopy (FESEM) revealed dispersed inclusions and microvoids acting as stress concentrators, consistent with reduced ductility. Crucially, progressive reduction of back pressure during processing optimization was essential for stabilizing melt flow and minimizing shear-induced degradation. This adjustment enabled consistent mold filling despite the material's variability. The results demonstrate that mixed HDPE waste can be successfully valorized for non-structural applications such as plastic lumber or pallets, providing a sustainable pathway for recycling heterogeneous streams without costly pre-treatment or compatibilization., This research was funded by MCIN/AEI/10.13039/501100011033 and by the European Union NextGenerationEU /PRTR through the grant PID2023-152869OB-C22 and PID2024- 157368NB-C33, and by MCIN/AEI/10.13039/501100011033 through the TED-AEI Project (grant TED2021-129920A-C43) and ERDF A way of making Europe .
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Preparation and Characterization of New Bioplastics Based on Polybutylene Succinate (PBS)

  • Barrino, Federico
  • Schiraldi, Chiara
  • Rosa-Ramírez, Harrison de la|||0000-0002-2913-7938
  • López-Martínez, Juan|||0000-0001-6904-2282
  • Samper, María-Dolores|||0000-0002-5102-8412
[EN] Sea and environmental pollution due to microplastics are global problems that in recent years have attracted particular interest in the scientific community. The increase in the world population and the consequent consumerism of non-reusable materials are amplifying these problems. In this manuscript, we present novel bioplastics, which are completely biodegradable, for their potential use in food packaging, to replace fossil-fuel-derived plastic films and slow food degradation due to oxidative processes or microbial contamination. In this study, thin films based on polybutylene succinate (PBS) were prepared to reduce pollution, and different percentages by weight (1, 2 and 3 wt%) of extra virgin olive oil (EVO) and coconut oil (CO) were included to improve the chemico-physical properties of the polymer and possibly improve the functionality of the films in terms of prolonged food preservation. Attenuated total reflectance Fourier transform infrared (ATR/FTIR) spectroscopy was used to evaluate the interactions between the polymer and the oil. Furthermore, the mechanical properties and thermal behavior of the films were evaluated as a function of the oil content. A scanning electron microscopy (SEM) micrograph showed the surface morphology and the thickness of the materials. Finally, apple and kiwi were selected for a food-contact test, and the wrapped sliced fruit was monitored and evaluated for 12 days to macroscopically evaluate the oxidative process and/or eventually occurring contamination. The films were shown to reduce the browning of sliced fruit due to oxidation, and no molds were evidenced up to 10/12 days of observation with the addition of PBS, with 3 wt% of EVO achieving the best outcomes., This research was funded by MCIN/AEI/10.13039/501100011033 through PID-AEI Project (grant PID2021-123753NA-C33 and PID2020-116496RB-C22), TED-AEI Project (grants TED2021-129920A-C43), and, as appropriate, by ERDF: A way of making Europe , by the European Union , or by the European Union NextGenerationEU/PRTR .
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Plasticized Mechanical Recycled PLA Films Reinforced with Microbial Cellulose Particles Obtained from Kombucha Fermented in Yerba Mate Waste

  • Agüero, Ángel
  • Corral Perianes, Esther
  • Abarca de las Muelas, Sara Soledad
  • García-Soto, María del Mar de la Fuente
  • Peltzer, Mercedes Ana
  • Arrieta, Marina Patricia
  • Lascano-Aimacaña, Diego Sebastián|||0000-0002-0996-1946
  • Balart, Rafael|||0000-0001-5670-7126
[EN] In this study, yerba mate waste (YMW) was used to produce a kombucha beverage, and the obtained microbial cellulose produced as a byproduct (KMW) was used to reinforce a mechanically recycled poly(lactic acid) (r¿PLA) matrix. Microbial cellulosic particles were also produced in pristine yerba mate for comparison (KMN). To simulate the revalorization of the industrial PLA products rejected during the production line, PLA was subjected to three extrusion cycles, and the resultant pellets (r3¿PLA) were then plasticized with 15 wt.% of acetyl tributyl citrate ester (ATBC) to obtain optically transparent and flexible films by the solvent casting method. The plasticized r3¿PLA¿ATBC matrix was then loaded with KMW and KMN in 1 and 3 wt.%. The use of plasticizer allowed a good dispersion of microbial cellulose particles into the r3¿PLA matrix, allowing us to obtain flexible and transparent films which showed good structural and mechanical performance. Additionally, the obtained films showed antioxidant properties, as was proven by release analyses conducted in direct contact with a fatty food simulant. The results suggest the potential interest of these recycled and biobased materials, which are obtained from the revalorization of food waste, for their industrial application in food packaging and agricultural films., This research was funded by the Spanish Ministry of Science and Innovation (MICINN) through PID‐AEI project (grants PID2020‐116496RB‐C22 and PID2021‐123753NA‐C32) and TED‐ AEI project (grants TED2021‐129920A‐C43 and TED2021‐131762A‐I00) funded by MCIN/AEI/10.13039/501100011033 and by ERDF A way of making Europe by the European Union . It was also funded by Comunidad de Madrid‐CAM ( Ayudas de Estímulo a la Investigación de Jóvenes Doctores de la Universidad Politécnica de Madrid , APOYO‐JOVENES‐21‐VUI9G6‐56‐ I7GABQ), Generalitat Valenciana‐GVA grant numbers AICO/2021/025 and CIGE/2021/094 and National University of Quilmes (UNQ, Argentina) through the R&D program (Expediente 1300/19). Ph.D. Ángel Agüero and Ph.D. Diego Lascano acknowledge the Margarita Salas postdoctoral grants from the Ministerio de Universidades, Spain, funded by the European Union Next Generation EU.