Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 10
Encontrada(s) 1 página(s)

Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Singular spectrum analysis filtering and Fourier inversion: an efficient and fast way to improve resolution and quality of current density maps with low-cost Hall scanning systems

  • Amorós, J.
  • Duran, Arnau
  • Carrera i Vilanova, Miquel
  • López, Josep
  • Granados, X.
We provide a Biot–Savart inversion scheme that, for any two-dimensional, or bulk with planar crystallization, high-temperature superconducting (HTS) sample, determines current density maps with a higher resolution and accuracy than previous procedures and at a fraction of its computational cost. The starting point of our scheme is a Hall scanning microscopy map of the out-of-plane component of the magnetic field generated by the current. Such maps are noisy in scans of real samples with commercial-grade equipment, and their error is the limiting factor in any Biot–Savart inversion scheme. The main innovation of our proposed scheme is a singular spectrum analysis (SSA) filtering of the Hall probe maps, which cancels measurement errors such as noise or drifts without introducing any artifacts in the field map. The SSA filtering of the Hall probe data is so successful in this task that the resulting magnetic field map does not require an overdetermined QR inversion, allowing Fourier inversion of the Biot–Savart problem. Our implementation of SSA filtering of the Hall scan measurements, followed by Biot–Savart inversion using the fast Fourier transform (FFT), is applied to both simulations and real samples of HTS tape stacks. The algorithm works in cases where ill conditioning ruled out the application of Fourier inversion, and achieves a finer resolution for a fraction of the cost of the QR inversion used to date. The computation passes physical and statistical validity tests in all cases, and in three-dimensional samples it is shown to yield the average, with a depth-dependent weight, of the current density circulating in the different layers of the sample., We acknowledge the financial support from the Spanish Ministry of Economy and Competitiveness through the Severo Ochoa Programme (SEV-2015-0496), CONSOLIDER Excellence Network (MAT2015-68994-REDC), COACHSUPENERGY project (MAT2014-51778-C2-1-R, co-financed by FEDER), GAP project (MTM2015-69135-P) and SUPERINKS project (RTC-2015-3640-3, co-financed by FEDER); the European Union for the FASTGRID project (H2020-NMBP-18-2016-IA-72109) and WPMAG 5 (H2020-EUROfusion); and the Catalan Government with 2017-SGR-932, 2014-SGR-753 and Xarmae.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Growth of all-chemical high critical current YBa2Cu3O7−δ thick films and coated conductors

  • Pop, Cornelia
  • Villarejo, Bohores
  • Pino, Flavio
  • Mundet, Bernat
  • Ricart, Susagna
  • Palau, M. de
  • Puig Molina, Teresa
  • Obradors, Xavier
The achievement of high critical currents in 'all-chemical' YBa2Cu3O7−δ thick films from low cost and versatile chemical solution deposition (CSD) methodology is still an open issue. Here we report a study of the nucleation and growth conditions to achieve YBa2Cu3O7−δ films in excess of 1 micron using single pass inkjet printing or multideposition of low-fluorine metalorganic precursors. Growth conditions of thick YBa2Cu3O7−δ layers are first investigated on LaAlO3, where there is no interfacial chemical reactivity. The second architecture investigated is an 'all-chemical' CSDCe0.9Zr0.1O2(CZO)/YSZ multilayer on single crystal substrates which serves as model system for coated conductors. Finally, the 'all-chemical' coated conductor architecture CSDYBa2Cu3O7/CSDCZO/ABADYSZ/stainless steel, where ABAD stands for alternating beam assisted deposition, is investigated. The nucleation conditions of YBa2Cu3O7−δ films on top of CΖΟ cap layers have been selected to minimize the formation of the BaCeO3 phase at the interface. We demonstrate that by combining the use of Ag additives in the starting YBCO solution and processing conditions leading to low supersaturation (high water pressure and low temperature) we can achieve ~1 μm thick YBa2Cu3O7−δ films and coated conductors with high critical currents of ${{I}_{c}}^{sf}$ = 390 and 100 A/cm-w, respectively, at 77 K and self-field. The achieved control of the interfacial reactivity with CeO2 cap layers opens a route for further increasing film thickness and critical currents in 'all-chemical' YBa2Cu3O7−δ coated conductors., All authors acknowledge the EU (EU-FP7 NMP-LA-2012-280432 EUROTAPES project and H2020-NMBP-18-2016-IA-72109 FASTGRID project), COST CA16218 NANOCOHYBRY, MINECO (COACHSUPENERGY, MAT2014-51778-C2-1-R and SUPERINKS) and Generalitat de Catalunya (2017SGR 1519 and Xarmae). ICMAB acknowledges the Center of Excellence award Severo Ochoa SEV-2015-0496. Special thanks are given to Bruker HTS Company from Germany for providing the ABADYSZ/SS metallic substrates., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Singular spectrum analysis filtering and Fourier inversion: an efficient and fast way to improve resolution and quality of current density maps with low-cost Hall scanning systems

  • Amorós, Jaume
  • Duran, Arnau
  • Carrera, Miquel
  • López, Josep
  • Granados, Xavier
We provide a Biot–Savart inversion scheme that, for any two-dimensional, or bulk with planar crystallization, high-temperature superconducting (HTS) sample, determines current density maps with a higher resolution and accuracy than previous procedures and at a fraction of its computational cost. The starting point of our scheme is a Hall scanning microscopy map of the out-of-plane component of the magnetic field generated by the current. Such maps are noisy in scans of real samples with commercial-grade equipment, and their error is the limiting factor in any Biot–Savart inversion scheme. The main innovation of our proposed scheme is a singular spectrum analysis (SSA) filtering of the Hall probe maps, which cancels measurement errors such as noise or drifts without introducing any artifacts in the field map. The SSA filtering of the Hall probe data is so successful in this task that the resulting magnetic field map does not require an overdetermined QR inversion, allowing Fourier inversion of the Biot–Savart problem. Our implementation of SSA filtering of the Hall scan measurements, followed by Biot–Savart inversion using the fast Fourier transform (FFT), is applied to both simulations and real samples of HTS tape stacks. The algorithm works in cases where ill conditioning ruled out the application of Fourier inversion, and achieves a finer resolution for a fraction of the cost of the QR inversion used to date. The computation passes physical and statistical validity tests in all cases, and in three-dimensional samples it is shown to yield the average, with a depth-dependent weight, of the current density circulating in the different layers of the sample., We acknowledge the financial support from the Spanish Ministry of Economy and Competitiveness through the Severo Ochoa Programme (SEV-2015-0496), CONSOLIDER Excellence Network (MAT2015-68994-REDC), COACHSUPENERGY project (MAT2014-51778-C2-1-R, co-financed by FEDER), GAP project (MTM2015-69135-P) and SUPERINKS project (RTC-2015-3640-3, co-financed by FEDER); the European Union for the FASTGRID project (H2020-NMBP-18-2016-IA-72109) and WPMAG 5 (H2020-EUROfusion); and the Catalan Government with 2017-SGR-932, 2014-SGR-753 and Xarmae., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Status of the European Union Project FASTGRID

  • Tixador, Pascal
  • Bauer, Markus
  • Bruzek, Christian-Eric
  • Calleja Lázaro, Alberto
  • Deutscher, Guy
  • Dutoit, Bertrand
  • Gomory, Fedor
  • Martini, Luciano
  • Noe, Mathias
  • Obradors, Xavier
  • Pekarčíková, Marcela
  • Sirois, Frédéric
High voltage direct current super-grids are one attractive solution for the transmission of bulk power of renewable electricity over long distances. Their protection is still an issue and superconducting fault current limiters (SCFCL) offer attractive perspectives. However, the actual superconducting tapes are not yet properly designed for operation at high voltages (>100 kV): The electric field developed during the current limitation is still too low (approximately 50 V/m for 50 ms) and the limiter requires too long lengths of tape. The European project FASTGRID aims at improving the properties of the REBCO tapes to enhance significantly (by 2-3 times) the electric field limit and so the economical SCFCL attractiveness. We use advanced THEVA tapes. Substantial improvements are also planned on the stabilizer (shunt) layer. Several shunt ways are under investigations. Other improvement on the tape properties will be carried out, namely the increase of the normal zone propagation velocity by at least one order of magnitude, with the help of the innovative current flow diverter architecture. The optimized conductor will be used in a SCFCL module (≈1.5 kA-50 kV) tested at 65 K. We will monitor the temperature along the conductor using an attached optical fibre. FASTGRID will also develop innovative tapes based on sapphire substrate, which can tolerate very high electric fields, in the range of kilovolts per meter. Validated on the laboratory scale, this game-changing technology needs to be implemented at long lengths with an industrial process. We will provide an overview of the project and its first results., This work was supported by the European Union's Horizon 2020 research and innovative programme under Grant 721019., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Normal zone propagation in various REBCO tape architectures

  • Lacroix, Christian
  • Giguère, Jaël
  • Bergeron Hartman, Simon Mathieu
  • Ben Saad, Haïfa
  • Martin, Anthony
  • Leduc, Thomas
  • Gendron-Paul, Maxime
  • Bellil, Zakaria
  • Fournier-Lupien, Jean-Hughes
  • Moret, Lucile
  • Barusco, Pedro
  • Granados, Xavier
  • Obradors, Xavier
  • Pekarčíková, Marcela
  • Gömöry, Fedor
  • Grosse, Veit
  • Bauer, Markus
  • Sirois, Frédéric
The normal zone propagation velocity (NZPV) of three families of REBCO tape architectures designed for superconducting fault current limiters and to be used in high voltage direct current transmission systems has been measured experimentally in liquid nitrogen at atmospheric pressure. The measured NZPVs span more than three orders of magnitude depending on the tape architectures. Numerical simulations based on finite elements allow us to reproduce the experiments well. The dynamic current transfer length (CTL) extracted from the numerical simulations was found to be the dominating characteristic length determining the NZPV instead of the thermal diffusion length. We therefore propose a simple analytical model, whose key parameters are the dynamic CTL, the heat capacity and the resistive losses in the metallic layers, to calculate the NZPV., The authors acknowledge the funding of this research by FASTGRID Project (EU-H2020, 721019), the Projects COACHSUPENERGY (MAT2014-51778-C2-1-R), SUMATE (RTI2018-095853-BC21 and RTI2018-095853-B-C22) from the Spanish Ministry of Economy and Competitiveness which were cofunded by the European Regional Development Fund, the Project 2017-SGR 753 from Generalitat de Catalunya and the COST Action NANOCOHYBRI (CA16218). Polytechnique Montréal authors also acknowledge NSERC (Canada), FRQNT (Québec), the RQMP infrastructure and CMC microsystems for financial support. ICMAB authors also acknowledge the Center of Excellence awards Severo Ochoa SEV-2015-0496 and CEX2019-000917-S., With funding from the Spanish government through the ‘Severo Ochoa Centre of Excellence’ accreditation (CEX2019-000917-S)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Chemical Solution Deposition of Insulating Yttria Nanolayers as Current Flow Diverter in Superconducting GdBa2Cu3O7-δ Coated Conductors

  • Barusco, Pedro
  • Granados, Xavier
  • Saltarelli, Lavinia
  • Fournier-Lupien, Jean-Hughes
  • Lacroix, Christian
  • Saad, Haifa Ben
  • Sirois, Frédéric
  • Vlad, Valentina Roxana
  • Calleja, Albert
  • Grosse, Veit
  • Puig Molina, Teresa
  • Obradors, Xavier
The primary benefit of a metallic stabilization/shunt in high temperature superconductor (HTS) coated conductors (CCs) is to prevent joule heating damage by providing an alternative path for the current flow during the HTS normal state transition (i.e., quench). However, the shunt presence in combination with unavoidable fluctuations in the critical current (I c) of the HTS film can develop a localized quench along the CC's length if the operational current is kept close to I c. This scenario, also known as the hot-spot regime, can lead to the rupture of the CC if the local quench does not propagate fast enough. The current flow diverter (CFD) is the CC architecture concept that has proven to increase the conductor's robustness against a hot-spot regime by simply boosting the quench velocity in the CC, which avoids the shunt compromise in some applications. This work investigates a practical manufacturing route for incorporating the CFD architecture in a reel-to-reel system via the preparation of yttrium oxide (Y2O3) as an insulating thin nanolayer (∼100 nm) on top of a GdBa2Cu3O7 (GdBCO) superconductor. Chemical solution deposition (CSD) using ink jet printing (IJP) is shown to be a suitable manufacturing approach. Two sequences of the experimental steps have been investigated, where oxygenation of the GdBCO layer is performed after or before the solution deposition and the Y2O3 nanolayer thermal treatment formation step. A correlated analysis of the microstructure, in situ oxygenation kinetics, and superconducting properties of the Ag/Y2O3/GdBCO trilayer processed under different conditions shows that a new customized functional CC can be prepared. The successful achievement of the CFD effect in the case of the preoxygenated customized CC was confirmed by measuring the current transfer length, thus demonstrating the effectiveness of the CSD-IJP as a processing method., We acknowledge the funding of this research by FASTGRID Project (EU-H2020, 721019); the Projects COACHSUPENERGY (MAT2014-51778-C2-1-R) and SUMATE (RTI2018-095853-BC21 and RTI2018-095853-B-C22) from the Spanish Ministry of Economy and Competitiveness, which were cofunded by the European Regional Development Fund; and the Project 2017-SGR 753 from Generalitat de Catalunya and the COST Action NANOCOHYBRI (CA16218). ICMAB authors also acknowledge the Center of Excellence awards Severo Ochoa SEV-2015-0496 and CEX2019-000917-S, With funding from the Spanish government through the ‘Severo Ochoa Centre of Excellence’ accreditation (CEX2019-000917-S)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

A sulfurization method for creating the buffer-layers current flow diverter architecture in REBa2Cu3O7 coated conductors

  • Barusco, Pedro
  • Giguère, Jael
  • Lacroix, Christian
  • Sirois, Frédéric
  • Granados, Xavier
  • Puig Molina, Teresa
  • Obradors, Xavier
The current flow diverter (CFD) is a known concept that has proven to effectively reduce the probability of destructive hot spots in REBa2Cu3O7 (REBCO; RE = rare earth) coated conductors (CCs) by boosting the normal zone propagation velocity. However, the implementation of the CFD concept requires additional steps in a fabrication process that is already complex and has struggled to find a simple reel-to-reel fabrication method. This work reports on the details of a fabrication route for the buffer-layers-CFD (bCFD) architecture using a solid-vapor silver sulfurization technique to tune the geometry of the metal stabilizer in the high-temperature superconductor tape. The analysis of the microstructure and superconducting properties of the Ag2S/Ag/GdBCO trilayer processed under different conditions shows how we achieved a new customized functional CC with the bCFD architecture. In DC limitation experiments, this bCFD-sulfide architecture allowed to generate an electric potential much faster than the conventional architecture (60 V s−1 vs. 1.2 V s−1) thanks to the strong enhancement of the NPZV., The authors acknowledge the funding of this research by the FASTGRID project (EU-H2020, 721019), the projects COACHSUPENERGY (MAT2014-51778-C2-1-R), SUMATE (RTI2018-095853-BC21 and RTI2018-095853-B-C22) from the Spanish Ministry of Economy and Competitiveness which were co-funded by the European Regional Development Fund, the project 2017-SGR 753 from Generalitat de Catalunya and the COST Action NANOCOHYBRI (CA16218). ICMAB authors also acknowledge the Center of Excellence awards Severo Ochoa SEV-2015-0496 and CEX2019-000917-S., With funding from the Spanish government through the ‘Severo Ochoa Centre of Excellence’ accreditation (CEX2019-000917-S)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Otros (Other)

Progress in superconducting REBa2Cu3O7 (RE = rare earth) coated conductors derived from fluorinated solutions

  • Obradors, Xavier
  • Puig Molina, Teresa
  • Ricart, Susagna
  • Palau, Anna
  • Coll, Mariona
  • Gutierrez Royo, Joffre 
  • Farjas, Jordi
  • Bartolomé, Elena
In this work, we review recent progress achieved in the use of chemical solution deposition (CSD) based on fluorinated metalorganic precursors to grow superconducting REBa2Cu3O7 (REBCO) films and coated conductors (CCs). We examine, first of all, the advances in optimizing the steps related to the solutions preparation, deposition and pyrolysis based on novel low-fluorine metalorganic solutions. We show that a new type of multifunctional colloidal solutions including preformed nanoparticles (NPs), can be used to introduce artificial pinning centers (APCs). We analyze how to disentangle the complex physico-chemical transformations occurring during the pyrolysis with the purpose of maximizing the film thicknesses. Understanding the nucleation and growth mechanisms is shown to be critical to achieve a fine tuning of the final microstructure, either using the spontaneous segregation or the colloidal solution approaches, and make industrially scalable this process. Advanced nanostructural studies have deeply modified our understanding of the defect structure and its genealogy. It is remarkable the key role played by the high concentration of randomly distributed and oriented BaMO3 (M = Zr, Hf) NPs which enhance the concentration of APCs, such as stacking faults and the associated partial dislocations. Correlating the defect structure with the critical current density Jc (H,T,θ) allows to reach a tight control of the vortex pinning properties and to devise a general scheme of the vortex pinning landscape in the whole H-T phase diagram. We also refer to the outstanding recent achievements in enhancing the vortex pinning strength by shifting the carrier concentration in REBCO films towards the overdoped state, where the pinning energy is maximum and so, record values of critical current densities are achieved. This confirms the performance competitiveness of nanocomposite CCs prepared through the CSD route. We conclude with a short summary of the progress in scaling the CC manufacturing using fluorinated solutions., Authors acknowledge the European Union Research Council for EUROTAPES (EU-FP7-NMP-LA-2012-280432) and FASTGRID (EU-H2020, 721019) projects and EU COST actions OPERA (CA20116) and SUPERQUMAP (CA-21144); the European Research Council for ULTRASUPERTAPE (ERC-2014-ADG-669504), IMPACT (ERC-2019-PoC-8749) and SMS-INKS (ERC-2022-PoC-101081998) projects. Also acknowledged is the financial support from the Spanish Ministry of Science and Innovation and the European Regional Development Fund, MCIU/AEI/FEDER for COACHSUPENERGY project (MAT2014-51778-C2-1-R and MAT2014-51778-C2-2-R), SuMaTe (RTI2018-095853-B-C21 and RTI2018-095853-B-C22), SUPERENERTECH (PID2021-127297OB-C21, PID2021-127297OB-C22) and PID2022-138492NB-I00, FUNMAT and FUNFUTURE ICMAB 'Severo Ochoa' Program for Centers of Excellence in R&D (SEV-2015-0496, CEX2019-000917-S) and HTS-JOINTS (PDC2022-133208-I00). They also thank the PTI+ TransEner CSIC program for Spanish NGEU (Regulation (EU) 2020/2094) and Catalan Government for 2017 SGR 1519 and 2021 SGR 00440 and that of Aragon for RASMIA (E12-23R)., With funding from the Spanish government through the ‘Severo Ochoa Centre of Excellence’ accreditation (CEX2019-000917-S)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Enhanced Normal Zone Propagation Velocity in REBCO Coated Conductors Using an Intermetallic Stabilizer Coating

  • Barusco, Pedro
  • Ben-Saad, Hamda
  • Horn-Bourque, D.
  • Lacroix, Christian
  • Sirois, Frédéric
  • Puig Molina, Teresa
  • Gutierrez Royo, Joffre 
  • Granados, Xavier
  • Obradors, Xavier
The Current Flow Diverter (CFD) is an established concept that has proven to effectively reduce the probability of destructive hot spots by boosting the normal zone propagation velocity (NZPV) in commercial REBa2Cu3O7 (REBCO; RE = Rare Earth) coated conductors (CC). However, incorporating the CFD concept requires finding a scalable method that is also compatible with the already established R2R fabrication process used by CC manufacturers. This study presents a new simple & cost-effective proof-of-concept technique capable of recreating the CFD architecture in commercial CCs coated with silver. The technique is based on promoting a locally controlled thin film diffusion reaction between the silver stabilizer and pure indium. Due to fast diffusion in the Ag-In system, stable Intermetallic Compounds (IMC) are formed throughout the whole thickness of the silver layer reaching the REBCO interface. The presence of Ag-In IMC in the interface safely increases the interfacial resistance (Ω-cm2) by orders of magnitude, thus allowing to safely form the CFD interlayer. Silver-coated tape samples altered using this CFD-IMC have shown an NZPV increase of 5-8x when compared with pristine samples., This work was supported in part by the FASTGRID Project under Grant EUH2020-721019, in part by the Projects SUPERENERTECH under Grant PID2021-127297OB-C21, in part by Spanish Ministry of Economy and Competitiveness which were co-funded by the European Regional Development Fund throughSUMATEunderGrantsRTI2018-095853-BC21 and RTI2018-095853-B-C22, in part by the MCIN/AEI/10.13039/501100011033 and EU “NextGenerationEU”/PRTR through SUPERPOWER Project under Grant TED2021-130004B-I00, in part by the Generalitat de Catalunya under Grant 2017-SGR 753, and in part by the COST Action NANOCOHYBRI under Grant CA16218. The work of P. Barusco, T. Puig, X. Granados, J. Guriérrez and X. Obradors was supported by the Center of Excellence Awards Severo Ochoa under Grants SEV-2015-0496 and CEX2019-000917-S., With funding from the Spanish government through the ‘Severo Ochoa Centre of Excellence’ accreditation (CEX2019-000917-S)., Peer reviewed
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Singular spectrum analysis filtering and Fourier inversion: an efficient and fast way to improve resolution and quality of current density maps with low-cost Hall scanning systems

  • Amorós, J.
  • Duran, Arnau
  • Carrera i Vilanova, Miquel
  • López, Josep
  • Granados, X.
We provide a Biot–Savart inversion scheme that, for any two-dimensional, or bulk with planar crystallization, high-temperature superconducting (HTS) sample, determines current density maps with a higher resolution and accuracy than previous procedures and at a fraction of its computational cost. The starting point of our scheme is a Hall scanning microscopy map of the out-of-plane component of the magnetic field generated by the current. Such maps are noisy in scans of real samples with commercial-grade equipment, and their error is the limiting factor in any Biot–Savart inversion scheme. The main innovation of our proposed scheme is a singular spectrum analysis (SSA) filtering of the Hall probe maps, which cancels measurement errors such as noise or drifts without introducing any artifacts in the field map. The SSA filtering of the Hall probe data is so successful in this task that the resulting magnetic field map does not require an overdetermined QR inversion, allowing Fourier inversion of the Biot–Savart problem. Our implementation of SSA filtering of the Hall scan measurements, followed by Biot–Savart inversion using the fast Fourier transform (FFT), is applied to both simulations and real samples of HTS tape stacks. The algorithm works in cases where ill conditioning ruled out the application of Fourier inversion, and achieves a finer resolution for a fraction of the cost of the QR inversion used to date. The computation passes physical and statistical validity tests in all cases, and in three-dimensional samples it is shown to yield the average, with a depth-dependent weight, of the current density circulating in the different layers of the sample., We acknowledge the financial support from the Spanish Ministry of Economy and Competitiveness through the Severo Ochoa Programme (SEV-2015-0496), CONSOLIDER Excellence Network (MAT2015-68994-REDC), COACHSUPENERGY project (MAT2014-51778-C2-1-R, co-financed by FEDER), GAP project (MTM2015-69135-P) and SUPERINKS project (RTC-2015-3640-3, co-financed by FEDER); the European Union for the FASTGRID project (H2020-NMBP-18-2016-IA-72109) and WPMAG 5 (H2020-EUROfusion); and the Catalan Government with 2017-SGR-932, 2014-SGR-753 and Xarmae.