Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 703
Encontrada(s) 8 página(s)

BULERIA. Repositorio Institucional de la Universidad de León
Publicación Artículo científico (JournalArticle)

Quantification of source specific black carbon scavenging using an aethalometer and a disdrometer

  • Blanco Alegre, Carlos del
  • Calvo Gordaliza, Ana Isabel
  • Coz Diego, Esther
  • Castro Izquierdo, Amaya
  • Oduber Pérez, Fernanda Isabel
  • Prév̂ot, André Stephan Henry
  • Močnik, Griša
  • Fraile Laiz, Roberto
[EN] Aerosol black carbon (BC) is the second strongest contributor to global warming, after CO2, and it is linked to many adverse health effects. A sampling campaign of 15 months was carried out in León (Spain) in order to evaluate the scavenging of BC with an ensemble aethalometer-disdrometer. The aethalometer provides the concentration of equivalent black carbon (eBC), and the disdrometer, the raindrop size distribution. A total of seventy-five rain events were studied and in 73% of them there was an effective (eBCinitial > eBCfinal) scavenging, with a mean decrease of 48 ± 37% in long rain events (>8 h) and 39 ± 38% in short rain events. The scavenging of BC is strongly related to its source. Thus, the scavenging coefficient (SC) mean value of the BC from fossil fuel (eBCff) for short and long rain events was 5.1 10−5 and 1.3 10−5 s−1, respectively. For the BC from biomass burning (eBCbb), the SC values were 1.6 10−4 and 2.8 10−5 s−1 in short and long events, respectively. There was a significant positive correlation between the SC and the number of drops with diameters between 0.375 and 2.5 mm. Rain scavenging of eBC was analyzed depending on the air mass origin obtaining an effective scavenging for air masses from Atlantic, Arctic and Africa. A linear model (R2 = 0.72) was built to estimate the ΔeBC values with variables from an aethalometer, a disdrometer and a weather station: eBC concentration before rain, swept volume and precipitation accumulated. A Kolmogorov-Smirnov statistical test confirmed the goodness of fit of the model to the measured data, SI, This work was partially supported by the Spanish Ministry of Economy and Competitiveness (Grant TEC2014-57821-R), the University of León (Programa Propio 2015/00054/001) and the AERORAIN project (Ministry of Economy and Competitiveness, Grant CGL2014-52556-R, co-financed with FEDER funds). F. Oduber acknowledges the grant BES-2015-074473 from the Ministry of Economy and Competitiveness. C. del Blanco Alegre acknowledges the grant FPU16/05764 from the Ministry of Education, Culture and Sports
BULERIA. Repositorio Institucional de la Universidad de León
Publicación Artículo científico (JournalArticle)

Links between recent trends in airborne pollen concentration, meteorological parameters and air pollutants

  • Oduber Pérez, Fernanda Isabel
  • Calvo Gordaliza, Ana Isabel
  • Blanco Alegre, Carlos del
  • Castro Izquierdo, Amaya
  • Vega Maray, Ana María
  • Valencia Barrera, Rosa María
  • Fernández González, María Delia
  • Fraile Laiz, Roberto
[EN] Biogenic aerosols may play an active role in various diseases. Pollutant gases and bioaerosols coexist in the atmosphere with the possibility of interacting with each other increasing their adverse impacts on human health. The study of long-term trends and the correlation between the pollen concentration from selected taxa (especially those related to allergies) and both the main atmospheric pollutants and the meteorological parameters has enabled us to identify the main factors that affect pollen concentration in the atmosphere. This study analyzes the long-term trend in CO, NO, NO2, PM10, SO2 and O3 from 1997 to 2016 and Fraxinus, Poaceae and Populus pollen concentrations in the city of León from 1994 to 2016. In general, there is a significant decreasing trend in atmospheric pollutant concentrations and a significant increasing trend in Fraxinus pollen concentrations. In addition, the influence of air pollutants and climatic factors on pollen concentrations and pollination period duration was studied using the Spearman correlation, showing that the flowering and pollination periods depend largely of the weather conditions before these periods and are influenced by air pollutant concentrations, SI, Spanish Ministry of Economy and Competitiveness (Grant TEC2014-57821-R), the University of León (Programa Propio 2015/00054/001 and 2018/00203/001) and AERORAIN project (Ministry of Economy and Competitiveness, Grant CGL2014-52556-R, co-financed with FEDER funds). F. Oduber acknowledges the grant BES-2015-074473 from the Spanish Ministry of Economy and Competitiveness. C. Blanco-Alegre acknowledges the grant FPU16-05764 from the Spanish Ministry of Education, Culture and Sport
BULERIA. Repositorio Institucional de la Universidad de León
Publicación Artículo científico (JournalArticle)

Characterization of aerosol sources in León (Spain) using Positive Matrix Factorization and weather types

  • Oduber Pérez, Fernanda Isabel
  • Calvo Gordaliza, Ana Isabel
  • Castro Izquierdo, Amaya
  • Blanco Alegre, Carlos del
  • Alves, Célia
  • Calzolai, Giulia
  • Nava, Silvia
  • Lucarelli, Franco
  • Nunes, Teresa Filomena Vieira, 1958-
  • Barata, Joana Filipa Brites, 1978-
  • Fraile Laiz, Roberto
[EN] A one-year aerosol sampling campaign, between 2016 and 2017, was conducted in a suburban area of León city, Spain. An association between the Positive Matrix Factorization (PMF) results and air masses through circulation weather types was carried out, through the construction of linear models from the PM10 concentrations and its chemical composition. The aerosol sources, identified by PMF six-factor solution, were: traffic (29%), aged sea salt (26%), secondary aerosols (16%), dust (13%), marine aerosol (7%) and biomass burning (3%). Traffic and secondary factors showed the highest PM10 contribution in the hybrid cyclonic types with wind component from the first and second quadrant. Anticyclonic types with wind component from the first quadrant exhibited high values of secondary, aged sea salt and dust factors. The highest contributions of the dust factor were also associated with northerly types. The linear models built for estimating the source apportionment of PM10, from aerosol chemical composition and geostrophic flow, showed positive coefficients for: westerly flows (WF) in marine factor, southerly flows (SF) in secondary and traffic factors, and shear southerly vorticities (ZS) in dust factor. Negative dependences were observed for ZS in aged sea salt factor and for SF in dust factor. The PM10 mass concentration calculated by the linear models and by the PMF model were strongly correlated. This can be very useful to determine the contribution of a specific source to PM10 in León, only by knowing some meteorological and chemical variables, SI, This study was partially supported by the Spanish Ministry of Economy and Competitiveness (Grant TEC2014-57821-R), the University of León (Programa Propio 2015/00054/001 and 2018/00203/001) and the AERORAIN project (Ministry of Economy and Competitiveness, Grant CGL2014-52556-R, co-financed with European FEDER funds). F. Oduber acknowledges the grant BES-2015-074473 from the Spanish Ministry of Economy and Competitiveness. C. Blanco-Alegre acknowledges the grant FPU16-05764 from the Spanish Ministry of Education, Culture and Sport. Thanks are also due for the financial support to CESAM (UIDB/50017/2020+UIDP/50017/2020), to FCT/MCTES through national funds, and the co-funding by the FEDER, within the PT2020 Partnership Agreement and Compete 2020
BULERIA. Repositorio Institucional de la Universidad de León
Publicación Artículo científico (JournalArticle)

Impact of vacuum cleaning on indoor air quality

  • Vicente, Estela Alexandra Domingos
  • Vicente, Ana Margarida Proença
  • Evtyugina, Margarita
  • Calvo Gordaliza, Ana Isabel
  • Oduber Pérez, Fernanda Isabel
  • Blanco Alegre, Carlos del
  • Castro Izquierdo, Amaya
  • Fraile Laiz, Roberto
  • Nunes, Teresa Filomena Vieira, 1958-
  • Lucarelli, Franco
  • Calzolai, Giulia
  • Nava, Silvia
  • Alves, Célia
[EN] Vacuum cleaning can be a household source of particulate matter (PM) both from the vacuum motor and from settled dust resuspension. Despite the evidence of this contribution to PM levels indoors, the effect of this source on PM composition is still unknown. In this study, four vacuum cleaners (washable filter bag less, wet, bagged and HEPA filter equipped robot) were tested for the emission rate of particulate mass and number. The detailed PM chemical characterisation included organic and elemental carbon, metals and organic speciation. PM10 emission rates from bagged vacuum operation were much higher (207 ± 99.0 μg min−1) compared with the ones obtained from wet (86.1 ± 16.9 μg min−1) and washable filter bag less vacuums (75.4 ± 7.89 μg min−1). Particle (8–322 nm) number emission rates ranged from 5.29 × 1011 (washable filter bag less vacuum) to 21.2 × 1011 (wet vacuum) particles min−1. Ratios of peak to background levels indicate that vacuuming can elevate the ultrafine particle number concentrations by a factor ranging from 4 to 61. No increase in PM mass or number concentrations was observed during the HEPA filter equipped vacuum operation. The increase in copper and elemental carbon PM10 contents during vacuuming suggested motor emissions. Organic compounds in PM10 included alkanes, PAHs, saccharides, phenolics, alcohols, acids, among others. However, it was not possible to establish a relationship between these compounds and vacuuming due to the vast array of possible household sources. The cancer risks associated with metals and PAH inhalation were negligible, SI, The sampling campaign was partially supported by the Spanish Ministry of Economy and Competitiveness (Grant TEC2014-57821-R), the University of León (Programa Propio 2015/00054/001 and 2018/00203/001) and the AERORAIN Project (Ministry of Economy and Competitiveness, Grant CGL2014-52556-R, co-financed with European FEDER Funds). Other part of the monitoring campaign and the analytical determinations of this work were funded by the project “Chemical and toxicological SOurce PROfiling of particulate matter in urban air (SOPRO)”, POCI-01-0145-FEDER-029574, supported by FEDER, through COMPETE2020 - Programa Operacional Competitividade e Internacionalização (POCI), and by National Funds (OE), through FCT/MCTES. An acknowledgment is due to the Portuguese Foundation of Science and Technology (FCT) and to the POHP/FSE Funding Programme for the fellowships with the references SFRH/BD/117993/2016 and SFRH/BPD/123176/2016. Ana Vicente is subsidised by national funds (OE), through FCT, I.P., in the framework contract foreseen in the numbers 4, 5 and 6 of article 23, of the Decree-Law 57/2016, of August 29, changed by Law 57/2017, of July 19. Thanks are due, for the financial support to CESAM (UIDB/50017/2020+UIDP/50017/2020), to FCT/MEC through national funds, and the co-funding by the FEDER, within the PT2020 Partnership Agreement and Compete 2020. F. Oduber and C. Blanco-Alegre acknowledge the grants BES-2015-074473 and FPU16-05764 from the Spanish Ministry of Economy and Competitiveness and from the Ministry of Education, Culture and Sports, Spain, respectively.
BULERIA. Repositorio Institucional de la Universidad de León
Publicación Artículo científico (JournalArticle)

Connection between NAO index and extreme precipitation in continental Spain

  • Caldevilla Domínguez, Pablo
  • Fraile Laiz, Roberto
  • Calvo Gordaliza, Ana Isabel
Ejemplar dedicado a: XXXV Jornadas Científicas de la AME: Predicción de tiempo y clima orientada a impactos - 19º Encuentro hispano-luso de Meteorología. Sesión de presentaciones en póster, [EN] The aim of this study is to find the connection between the NAO index and the number of episodes with extreme precipitations in continental Spain during the period 1982-2011, SI, Este trabajo fue parcialmente apoyado por el Ministerio de Economía y Com - petitiveness (Grant TEC2014 - 57821-R), de la Universidad de León (Programa Propio 2015/00054/001) y AERORAIN proyecto (Ministerio de Economía y Competitividad, de la Subvención CGL2014-52556-R, cofinanced)
BULERIA. Repositorio Institucional de la Universidad de León
Publicación Artículo científico (JournalArticle)

Daily behavior of urban Fluorescing Aerosol Particles in northwest Spain

  • Calvo Gordaliza, Ana Isabel
  • Baumgardner, Darrel
  • Castro Izquierdo, Amaya
  • Fernández González, María Delia
  • Vega Maray, Ana María
  • Valencia Barrera, Rosa María
  • Oduber Pérez, Fernanda Isabel
  • Blanco Alegre, Carlos del
  • Fraile Laiz, Roberto
[EN] Measurements of ambient aerosol particles at the University of León, León, Spain, were made in May and June 2015 with a Wideband Integrated Bioaerosol Spectrometer (WIBS). The WIBS detects Fluorescing Aerosol Particles (FAP) in the size range from 0.5 to 20 μm. These measurements were complemented with an analysis of pollen concentrations assessed with optical microscopy of samples captured with a volumetric Hirst spore trap. The total particle, FAP and pollen concentrations show clear, daily cycles. Whereas the total particle con- centrations maximize at 0800 and 2200 UTC, the FAP concentrations have peaks at midnight and 0800 UTC while the pollen has a broad peak between 1200 and 2000 UTC. The FAP larger than 2 μm represent 15–35% of the total particle population in this size range, maximizing at midnight UTC. Similar to what has been found by investigators at other locations, there is a strong positive correlation of the WIBS measured FAP with relative humidity; however, the pollen concentration is positively correlated with the temperature and anti-correlated with the relative humidity. Back trajectory analysis indicates that the largest FAP to total particle fractions are found in air masses arriving from the northeast with the second largest coming from the southwest. Given the location of the university in relation to the city and forested areas, this implies that the higher concentration FAP are coming from rural, probably natural, sources; however, more local, anthropogenic sources cannot be ruled out as a secondary source. The majority of the FAP that are identified from microscopy are fungal spores (Cladosporium, Aspergillus, Alternaria, Oidium) and pollen grains (mainly Poaceae, Quercus, Plantago, Rumex and Urticaceae). A comparison of the fluorescence fingerprints between laboratory generated FAP and the ambient particles showed some similarities; however, a significant fraction of the FAP are those whose fluorescence patterns do not match any of those that have been previously classified in the laboratory, SI, This study was partially supported by the Spanish Ministry of Economy and Competitiveness (Grant TEC2014-57821-R), the University of León (Programa Propio 2015/00054/001) and AERORAIN project (Ministry of Economy and Competitiveness, Grant CGL2014-52556-R, co-financed with FEDER funds). F. Oduber acknowledges the grant BES-2015-074473 from the Spanish Ministry of Economy and Competitiveness. C. Blanco-Alegre acknowledges the grant FPU16-05764 from the Spanish Ministry of Education, Culture and Sport. The authors gratefully acknowledge the NOAA Air Resources Laboratory (ARL) for the provision of the HYSPLIT transport and dispersion model and/or READY website (http://www.ready.noaa.gov) used in this publication
BULERIA. Repositorio Institucional de la Universidad de León
Publicación Artículo científico (JournalArticle)

Diseño de una aplicación informática para procesar los registros obtenidos por por el disdrómetro optico THIES LPM

  • Fernández Raga, María
  • Alfonso Cendón, Javier
  • Fraile Laiz, Roberto
Ejemplar dedicado a: XXXV Jornadas Científicas de la AME: Predicción de tiempo y clima orientada a impactos - 19º Encuentro hispano-luso de Meteorología. Sesión de presentaciones en póster, [ES] La obtención y gestión de bases de datos completas que recojan datos de las características de las gotas de los diferentes eventos de lluvia en cada lugar concreto resulta sumamente útil en Meteorología. La recogida de estos datos exige de instrumentos meteorológicos especializados, como los disdrómetros, y concretamente el disdrómetro óptico Laser Precipitation Monitor (LPM) de Thies Clima es uno de los más comunes. Este disdrómetro ha sido utilizado por la Universidad de León para el estudio de las gotas desde el año 2006, generando una base de datos tan grande y pesada que resulta muy complicada de gestionar y analizar. Es por tanto de alto interés para fines de investigación diseñar un programa informático que gestione las bases de datos y que permita realizar consultas de periodos de interés de una manera automática, extrayendo aquellas estadísticas y valores que resulten de mayor utilidad. Por lo tanto, el objetivo de este trabajo es diseñar una aplicación que permita procesar los registros obtenidos durante más de 10 años por un disdrómetro LPM Thies clima, y almacenarlos en texto plano en datos válidos para su posterior tratamiento. Para ello, hacemos uso del lenguaje Java que lee los datos, los procesa y los sube al servidor de base de datos. Una vez estos datos son almacenados, se pasan a mostrarse en una aplicación Web que, de forma gráfica, puede presentarlos por fechas, tamaños o velocidades, aportando una información válida para estudio de las precipitaciones. Esta aplicación fue implementada con un Login de seguridad para controlar el acceso de usuarios, y con un interfaz de usuario sencillo que permite que usuarios sin conocimientos en Java puedan ejecutar la aplicación sin ningún tipo de problema, SI, Este estudio ha sido parcialmente financiado por el Ministerio Español de Ciencia e Innovación (Proyecto TEC2014-57821-R y CGL2014-52556-R). María Fernández-Raga agradece además la beca postdoctoral José Castillejo del Ministerio Español de Ciencia e Innovación (Beca CAS16/00385)
BULERIA. Repositorio Institucional de la Universidad de León
Publicación Artículo científico (JournalArticle)

Influence of meteorological parameters on air pollutant concentrations in León, Spain

  • Oduber Pérez, Fernanda Isabel
  • Blanco Alegre, Carlos del
  • Calvo Gordaliza, Ana Isabel
  • Castro Izquierdo, Amaya
  • Sainz Villegas, Samuel
  • Martínez Fernández, Adrián
  • Fraile Laiz, Roberto
Ejemplar dedicado a: XXXV Jornadas Científicas de la AME: Predicción de tiempo y clima orientada a impactos - 19º Encuentro hispano-luso de Meteorología. Sesión de presentaciones en póster, [EN] The presence of pollutants in the atmosphere may cause a negative impact on human health and the environment. The main air pollutants are carbon monoxide (CO), nitrogen oxides (NOx), sulfur dioxide (SO2), ozone (O3) and particulate matter (PM). The correlation between the air pollutant concentrations and the weather variables provides valuable information about the emission sources and leads to a better understanding of the processes responsible for the spatial and temporal distribution of air pollutants. This enables policy makers to establish mitigation measures. The present study was carried out in León city, located in the northwest of the Iberian Peninsula (42° 36’ N, 05º 35’ W and 838 m above sea level). For this study, the data available in the Air Quality Network of Junta of Castilla y León (www.servicios.jcyl.es/esco) for the period between 1 January and 31 December 2016 were used. Two air quality stations were operating during the studied period (Fig.1): i) an urban traffic station located in San Ignacio de Loyola Avenue (Station 1, 05° 35’14”W 42° 36’14”N) and ii) a background station located in the Coto Escolar (Station 4, 05° 33’59”W 42° 34’31”N), SI, This work was partially supported by the Spanish Ministry of Economy and Competitiveness (Grant TEC2014-57821-R), the University of León (Programa Propio 2015/00054/001) and AERORAIN project (Ministry of Economy and Competitiveness, Grant CGL2014-52556-R, ERDF co-financed). F. Oduber acknowledges the grant BES- 2015-074473 from the Spanish Ministry of Economy and Competitiveness. C. Blanco- Alegre acknowledges the grant FPU16-05764 from the Spanish Ministry of Education, Culture and Sport
BULERIA. Repositorio Institucional de la Universidad de León
Publicación Artículo científico (JournalArticle)

Rainfall characteristics in León in 2016 and 2017

  • Blanco Alegre, Carlos del
  • Oduber Pérez, Fernanda Isabel
  • Calvo Gordaliza, Ana Isabel
  • Castro Izquierdo, Amaya
  • Martínez Fernández, Adrián
  • Sainz Villegas, Samuel
  • Fraile Laiz, Roberto
Ejemplar dedicado a: XXXV Jornadas Científicas de la AME: Predicción de tiempo y clima orientada a impactos - 19º Encuentro hispano-luso de Meteorología. Sesión de presentaciones en póster, [EN] Nowadays, air pollution is one of the principal risk to human health and rain is the main sink of aerosol particles in the atmosphere, since it is the main process to mitigate pollution. Furthermore, the study of rainfall characteristics is crucial because it can provide information about present and future risks in an area, related to rain amount or intensity. In order to know the characteristics of the precipitation in the city of León, rain was sampled during 2016 and 2017 using a Laser Precipitation Monitor (LPM) of Thies Clima which registered drops between 0.125 and 8 mm in 22 channels. Furthermore, a Circulation Weather Types (CWTs) classification was carried out based on Lamb (1972), to identify the weather type related to a peculiar synoptic situation in days with rain. Focusing on rain characteristics in the city of León, 3.23·109 drops m-2 have fallen in 2016 with a mean size of 0.36±0.20 mm and 1.06·109 drops m-2 in 2017 with a mean size of 0.35±0.19 mm. The rain characteristic according to Lamb Weather Types during rain events will be analyzed, SI, This work was partially supported by the Spanish Ministry of Economy and Com-petitiveness (Grant TEC2014-57821-R), the University of León (Programa Propio 2015/00054/001) and the AERORAIN project (Ministry of Economy and Competitive-ness, Grant CGL2014-52556-R, ERDF co-financed). F. Oduber acknowledges the grant BES-2015-074473 from the Ministry of Economy and Competitiveness. C. del Blanco Alegre acknowledges the grant FPU16/05764 from the Ministry of Education, Culture and Sports
BULERIA. Repositorio Institucional de la Universidad de León
Publicación Artículo científico (JournalArticle)

Capa límite en León: relación con los parámetros meteorológicos y con la concentración de contaminantes

  • Calles Avedillo, Cristina
  • Fraile Laiz, Roberto
  • Calvo Gordaliza, Ana Isabel
Ejemplar dedicado a: XXXV Jornadas Científicas de la AME: Predicción de tiempo y clima orientada a impactos - 19º Encuentro hispano-luso de Meteorología. Sesión de presentaciones en póster, [ES] La calidad del aire en una zona depende de la emisión e inmisión de los contaminantes y de los procesos que intervienen en su transporte y dispersión en la atmósfera. La Ley 34/2007 regula la calidad del aire y la protección del medio ambiente. La capa límite planetaria o PBL, se define como la capa atmosférica que interacciona directa-mente con la superficie terrestre, convirtiéndose en una zona de mezcla constante de los componentes atmosféricos. Juega un papel fundamental en la calidad del aire y en las condiciones meteorológicas (Selvaratnam et al., 2015). La altura de la PBL es muy variable (Seidel et al., 2012); los valores pueden oscilar desde unos pocos metros a uno o dos kilómetros. Su espesor depende de diversos factores (Núñez, 2002) como la topografía, la naturaleza de la cubierta vegetal, la velocidad del viento, las condiciones atmosféricas (clase de estabilidad), la tasa de insolación recibida, etc. El objetivo principal de este trabajo es el estudio de la relación entre la altura de la PBL y i) algunos parámetros meteorológicos (temperatura, humedad relativa y velocidad del viento) ii) la concentración de contaminantes registrados en dos estaciones de calidad del aire de la ciudad de León, durante el año 2016, SI, Este trabajo ha sido parcialmente financiado por el Ministerio de Economía y Competitividad (TEC2014-57821-R), la Universidad de León (Programa Propio 2015/00054/001) y el proyecto AERORAIN (Ministerio de Economía y Competitividad, CGL2014-52556-R, cofinanciado con fondos FEDER
BULERIA. Repositorio Institucional de la Universidad de León
Publicación Artículo científico (JournalArticle)

Influencia de los parámetros meteorológicos en la contaminación del aire en la ciudad de Santander

  • Martínez Fernández, Adrián
  • Sainz Villegas, Samuel
  • Blanco Alegre, Carlos del
  • Oduber Pérez, Fernanda Isabel
  • Calvo Gordaliza, Ana Isabel
  • Castro Izquierdo, Amaya
  • Fraile Laiz, Roberto
Ejemplar dedicado a: XXXV Jornadas Científicas de la AME: Predicción de tiempo y clima orientada a impactos - 19º Encuentro hispano-luso de Meteorología. Sesión de presentaciones en póster, [ES] Con este trabajo se pretende calcular, para cada tipo de tiempo, la concentración media de contaminantes presentes en la atmósfera y buscar las correlaciones significativas entre la concentración de dichos contaminantes y algunos parámetros meteorológicos en la ciudad de Santander. Para analizar las posibles diferencias significativas, se han aplicado tests no paramétricos. Estudios recientes han relacionado la exposición a contaminantes atmosféricos, en especial a material particulado, con enfermedades respiratorias y cardiovasculares, entre las que encontramos cáncer bronquial, enfisemas pulmonares, trombosis, coágulos e in-fartos que, en algunos casos, han llegado a causar la muerte (Rückerl et al., 2011). De los 3 millones de muertes debidas a la contaminación atmosférica que han sido estimadas en el mundo, alrededor de 193.000 han ocurrido en Europa y 7000 en España (Ortiz et al., 2017).En España la contaminación atmosférica es un problema emergente, sobre todo en las ciudades más pobladas, lo que ha llevado a adoptar medidas para reducir las concentraciones de los contaminantes presentes en el aire, principalmente provenientes de la industria y del transporte. Los eventos más críticos de contaminación atmosférica se asocian fundamentalmente a situaciones anticiclónicas e inversiones térmicas, que dificultan considerablemente la dispersión atmosférica, creando así una cúpula de contaminantes sobre la zona. El objetivo principal del presente trabajo es calcular para cada tipo de tiempo la concentración media de contaminantes presentes en la atmósfera y buscar las correlaciones significativas entre la concentración de los contaminantes y los parámetros meteorológicos obtenidos de los radiosondeos (diferenciando entre los tres tipos de estaciones de calidad del aire utilizadas, tráfico, industrial y urbana de fondo). Se ha aplicado el test no paramétrico de Kruskal-Wallis para analizar las diferencias significativas entre las diferentes estaciones de los contaminantes medidos. El gran volumen de tráfico e industria de la ciudad de Santander y la falta de estudios en la zona hacen de esta ciudad un área de estudio ideal para evaluar su calidad del aire. El presente trabajo pretende buscar relaciones entre la concentración de los contaminantes atmosféricos y las condiciones atmosféricas durante el año 2016, SI, Este trabajo ha sido parcialmente financiado por el Ministerio de Economía y Competitividad (TEC2014-57821-R), la Universidad de León (Programa Propio 2015/00054/001) y el proyecto AERORAIN (Ministerio de Economía y Competitividad, CGL2014-52556-R, cofinanciado con fondos FEDER). F. Oduber disfruta de un contrato BES-2015-074473 del Ministerio de Economía y Competitividad. C. Blanco-Alegre disfruta de un contrato FPU16-05764 del Ministerio de Educación, Cultura y Deporte
BULERIA. Repositorio Institucional de la Universidad de León
Publicación Artículo científico (JournalArticle)

Tipos de tiempo y calidad del aire en tres estaciones de fondo del NW peninsular

  • Sainz Villegas, Samuel
  • Martínez Fernández, Adrián
  • Calvo Gordaliza, Ana Isabel
  • Oduber Pérez, Fernanda Isabel
  • Blanco Alegre, Carlos del
  • Castro Izquierdo, Amaya
  • Fraile Laiz, Roberto
Ejemplar dedicado a: XXXV Jornadas Científicas de la AME: Predicción de tiempo y clima orientada a impactos - 19º Encuentro hispano-luso de Meteorología. Sesión de presentaciones en póster, [ES] La contaminación atmosférica se ha incrementado principalmente por el desarrollo de actividades industriales y económicas. Además, hay que tener en cuenta no sólo la contaminación atmosférica generada cerca de las fuentes, sino también la que se ha transportado hacia zonas alejadas, conocidas como regiones de fondo. En este trabajo se estudia la evolución de las concentraciones de los contaminantes atmosféricos en tres estaciones de fondo de la península ibérica y se buscan las posibles relaciones entre la concentración de contaminantes atmosféricos y las condiciones meteorológicas en dichas estaciones. La contaminación atmosférica es un problema que afecta tanto al medio ambiente como a la salud de las personas, provocado por la emisión de partículas, sustancias o formas de energía a la atmósfera. Este problema se ha visto magnificado en gran parte por el desarrollo de actividades industriales y económicas, especialmente a lo largo del siglo pasado (Calvo, 2009). Sin embargo, según indica la Agencia Europea de Medio Ambiente (EEA), las emisiones de algunos contaminantes están sufriendo una reducción en los últimos años, como consecuencia de la aparición de nuevas políticas de contaminación atmosférica. A pesar de esto, algunas zonas urbanas, siguen registrando elevadas concentraciones de contaminantes atmosféricos (EEA, 2017). Existe una gran diversidad de contaminantes atmosféricos entre los que podemos encontrar el ozono troposférico (O3), los óxidos de nitrógeno (NOx), los óxidos de azufre (SOx), el monóxido de carbono (CO), los compuestos orgánicos volátiles (COVs) y los aerosoles o material particulado (PM), entre otros (Ballester, 2005). En el presente trabajo nos centraremos especialmente en estos últimos. Algunos estudios recientes han incluido distintos parámetros meteorológicos estacionales para explicar las fluctuaciones en las concentraciones de contaminantes en la atmósfera (Calvo et al., 2012). Variables meteorológicas tales como la velocidad y la dirección del viento o la estabilidad atmosférica influyen en la contaminación del aire. En condiciones de velocidades del viento bajas y atmósfera altamente estable, la dispersión horizontal y la mezcla vertical se ven sensiblemente reducidas y en consecuencia las concentraciones de contaminantes serán más altas (Padró-Martínez et al., 2012). Las condiciones de atmósfera estable a menudo ocurren durante el invierno (meses fríos) y a las horas previas al amanecer (Hu et al., 2009). Algunas de las situaciones meteorológicas que pueden llegar a originar los escenarios de contaminación más dramáticos son los tipos de tiempo anticiclónicos estancados y las inversiones térmicas, SI, Este trabajo ha sido parcialmente financiado por el Ministerio de Economía y Competitividad (TEC2014-57821-R), la Universidad de León (Programa Propio 2015/00054/001) y el proyecto AERORAIN (Ministerio de Economía y Competitividad, CGL2014-52556-R, cofinanciado con fondos FEDER). Los datos fueron facilitados por el programa EMEP. F. Oduber disfruta de un contrato BES-2015-074473 del Ministerio de Economía y Competitividad. C. Blanco-Alegre disfruta de un contrato FPU16-05764 del Ministerio de Educación, Cultura y Deporte
BULERIA. Repositorio Institucional de la Universidad de León
Publicación Artículo científico (JournalArticle)

Vertical raindrop size distribution in central Spain: a case study

  • Fraile Laiz, Roberto
  • Castro Izquierdo, Amaya
  • González Colino, Miguel
  • Alonso Blanco, Elisabeth
  • Fernández Raga, María
  • Palencia Coto, María Covadonga
  • Calvo Gordaliza, Ana Isabel
[EN] A precipitation event that took place on 12 October 2008 in Madrid, Spain, is analyzed in detail. Three different devices were used to characterize the precipitation: a disdrometer, a rain gauge, and a Micro Rain Radar (MRR). These instruments determine precipitation intensity indirectly, based on measuring different parameters in different sampling points in the atmosphere. A comparative study was carried out based on the data provided by each of these devices, revealing that the disdrometer and the rain gauge measure similar precipitation intensity values, whereas the MRR measures different rain fall volumes. The distributions of drop sizes show that the mean diameter of the particles varied considerably depending on the altitude considered. The level at which saturation occurs in the atmosphere is decisive in the distribution of drop sizes between 2,700 m and 3,000 m. As time passes, the maximum precipitation intensities are registered at a lower height and are less intense. The maximum precipitation intensities occurred at altitudes above 1,000 m, while the maximum fall speeds are typically found at altitudes below 700 m, SI, This study was partially supported by the Spanish MINECO (Grants TEC2014-57821-R and CGL2014-52556-R)
BULERIA. Repositorio Institucional de la Universidad de León
Publicación Artículo científico (JournalArticle)

Impact of the wood combustion in an open fireplace on the air quality of a living room: Estimation of the respirable fraction

  • Castro Izquierdo, Amaya
  • Calvo Gordaliza, Ana Isabel
  • Blanco Alegre, Carlos del
  • Oduber Pérez, Fernanda Isabel
  • Alves, Célia dos Anjos
  • Coz Diego, Esther
  • Amato, Fulvio
  • Querol Carceller, Xavier
  • Fraile Laiz, Roberto
[EN] Presently, both in rural areas and in cities open fireplaces are still present and large quantities of wood are combusted every year. The present study aims to characterize aerosol size distribution, chemical composition and deposition in the human respiratory tract of particles emitted during the combustion of logs of oak in an open fireplace installed in the living room of a typical village house. CO2 and CO levels and aerosol size distribution have been continuously monitored and a PM10 sampler with two types of filters for chemical and microscopic analysis was also installed. The increment, between the operating periods and the indoor background, in the organic carbon and PM10 concentration due to the use of the fireplace is 15.7 ± 0.6 (mean ± standard deviation) and 58.5 ± 6.2 μg m−3, respectively. The two main polluting processes during the operation of the fireplace are the ignition with the subsequent refueling and the final cleaning of the residual ashes. In both phases mean values around 1800 particles cm−3 with CMD of 0.15 μm were measured. However, while PM10 levels of 130 ± 120 μg m−3 were estimated for the ignition stage, values of 200 ± 200 μg m−3 were obtained during the final cleaning step. Assessment conducted according to ISO standard 7708:1995, demonstrated that a person who stays in a living room when an open fireplace is lit will inhale, on average, 217 μg m−3 and 283 μg m−3 during the ignition and the refueling stages, respectively. Subsequent refueling proved to be much less polluting. The ashes removal can also be very polluting and dangerous to health if there are hidden small incandescent embers among the ashes (estimated PM10 of 132 μg m−3), reaching a CO2 level of 1940 ppm and a dangerous level of CO of 132 ppm, SI, This study was partially supported by the Spanish Ministry of Economy and Competitiveness (Grants TEC2014-57821-R and CGL2014-52556-R) co-financed with FEDER funds, the LIFE programme (AIRUSE, LIFE 11/ENV/ES/000584), and by AEROCLIMA project (Fundación Ramón Areces, CIVP16A1811). Furthermore, F. Oduber acknowledges the grant BES-2015-074473 from the Spanish Ministry of Economy and Competitiveness. C. Blanco-Alegre acknowledges the grant FPU16-05764 from the Spanish Ministry of Education, Culture and Sport
BULERIA. Repositorio Institucional de la Universidad de León
Publicación Artículo científico (JournalArticle)

Wildfire smoke plumes transport under a subsidence inversion: Climate and health implications in a distant urban area

  • Alonso Blanco, Elisabeth
  • Castro Izquierdo, Amaya
  • Calvo Gordaliza, Ana Isabel
  • Pont, Véronique
  • Mallet, Marc
  • Fraile Laiz, Roberto
[EN] This study shows the influence of two large wildfires (one of which was the largest wildfire ever recorded in the region of Castilla y León) in the north-west of the Iberian Peninsula upon the atmospheric air quality of the city of León, Spain, at approximately 70 km from the fires, on days with a strong subsidence inversion associated with high pressures. The vertical dispersion of the smoke plume was inhibited and this caused an increase in the particulate matter (PM) in the atmosphere. During this event, average values of up to 1700 ± 600 particles cm− 3 were registered, most of which corresponding to the smallest fraction of the fine mode. On the other hand, the count median diameter of the fine mode (CMDf) increased gradually from 0.09 to 0.14 μm. The PM10 and PM2.5 reached hourly values of 89 and 36 μg m− 3, respectively. This study also estimates the changes in the optical properties of the particles as well as the associated radiative forcing. The presence of an important load of absorbing aerosols was detected, with instantaneous radiative atmospheric forcing up to + 134.6 W m− 2. The estimations of the respirable fractions showed in healthy adults high levels of mass concentration of the aerosol that reaches the bronchioles and alveoli (up to 43 μg m− 3), SI, This study was partially supported by the Spanish Ministry of Economy and Competitiveness (Grant TEC2014-57821-R), the University of León (Programa Propio 2015/00054/001) and the AERORAIN project (Ministry of Economy and Competitiveness, Grant CGL2014-52556-R, co-financed with FEDER funds)
e-Archivo. Repositorio Institucional de la Universidad Carlos III de Madrid
Publicación Artículo científico (JournalArticle)

Optimized Update/Prediction Assignment for Lifting Transforms on Graphs

  • Martínez Enríquez, Eduardo
  • Cid Sueiro, Jesús
  • Díaz de María, Fernando
  • Ortega Gómez, Román Antonio
Transformations on graphs can provide compact representations of signals with many applications in denoising, feature extraction or compression. In particular, lifting transforms have the advantage of being critically sampled and invertible by construction, but the efficiency of the transform depends on the choice of a good bipartition of the graph into update (U) and prediction (P) nodes. This is the update/prediction (U=P) assignment problem, which is the focus of this paper. We analyze this problem theoretically and derive an optimal U=P assignment under assumptions about signal model and filters. Furthermore, we prove that the best U=P partition is related to the correlation between nodes on the graph and is not the one that minimizes the number of conflicts (connections between nodes of same label) or maximizes the weight of the cut. We also provide experimental results in randomly generated graph signals and real data from image and video signals that validate our theoretical conclusions, demonstrating improved performance over state of the art solutions for this problem., This work was supported in part by NSF under Grant CCF-1018977 and in part by the Spanish Ministry of Economy and Competitiveness under Grants TEC2014-53390-P, TEC2014-52289-R, TEC2016-81900-REDT/AEI and TEC2017-83838-R, Publicado
e-Archivo. Repositorio Institucional de la Universidad Carlos III de Madrid
Publicación Artículo científico (JournalArticle)

Gain-switching injection-locked dual optical frequency combs: characterization and optimization

  • Jerez González, Borja
  • Martín Mateos, Pedro
  • Prior Cano, Estefania
  • Dios Fernández, Cristina de
  • Acedo Gallardo, Pablo
In this work, the generation of dual optical frequency combs based on gain-switching and optical injection locking is experimentally examined. The study reveals that an effective process of optical injection can lead to optimized RF combs in terms of span and signal-to-noise ratio. The system also minimizes the overlap of lines and reduces the number of optical components involved, eliminating the need for any external modulator (electro-optic, acousto-optic). The validation of the system was performed as a dual-comb spectrometer, which allowed for determination of the absorption and dispersion profiles of the molecular transition of H-13CN at 1538.523 nm., Ministerio de Economía y Competitividad (MINECO) (RTC-2014-2661-7, TEC-2014-52147-R); Spanish Ministry of Education, Culture, and Sports (FPU014/06338).
e-Archivo. Repositorio Institucional de la Universidad Carlos III de Madrid
Publicación Artículo científico (JournalArticle)

Efficient scale-adaptive license plate detection system

  • Molina Moreno, Miguel
  • González Díaz, Iván
  • Díaz de María, Fernando
License plate detection is a common problem in traffic surveillance applications. Although some solutions have been proposed in the literature, their success is usually restricted to very specific scenarios, with their performance dropping in more demanding conditions. One of the main challenges to be addressed for this kind of systems is the varying scale of the license plates, which depends on the distance between the vehicles and the camera. Traditionally, systems have handled this issue by sequentially running single-scale detectors over a pyramid of images. This approach, although simplifies the training process, requires as many evaluations as considered scales, which leads to running times that grow linearly with the number of scales considered. In this paper, we propose a scale-adaptive deformable part-based model which, based on a well-known boosting algorithm, automatically models scale during the training phase by selecting the most prominent features at each scale and notably reduces the test detection time by avoiding the evaluation at different scales. In addition, our method incorporates an empirically constrained-deformation model that adapts to different levels of deformation shown by distinct local features within license plates. As shown in the experimental section, the proposed detector is robust and scale and perspective independent and can work in quite diverse scenarios. Experiments on two datasets show that the proposed method achieves a significantly better performance in comparison with other methods of the state of the art., This work was supported in part by the Spanish Ministry of Economy and Competitiveness under Grant TEC2014-53390-P and Grant TEC2017-84395-P and in part by the Spanish Department of Traffic, Spanish Ministry of Home Affairs, under Grant SPIP2014-1507.
Repositorio Digital de la UPF
Publicación Artículo científico (JournalArticle)

Dielectric properties of colon polyps, cancer, and normal mucosa: Ex vivo measurements from 0.5 to 20 GHz

  • Guardiola, Marta
  • Buitrago, Santiago
  • Fernández-Esparrach, Gloria
  • O’Callaghan, Joan M.
  • Romeu, Jordi
  • Cuatrecasas, Miriam
  • Córdova, Henry
  • González Ballester, Miguel Ángel, 1973-
  • Camara, Oscar
Purpose: Colorectal cancer is highly preventable by detecting and removing polyps, which are the precursors. Currently, the most accurate test is colonoscopy, but still misses 22% of polyps due to visualization limitations. In this paper, we preliminary assess the potential of microwave imaging and dielectric properties (e.g., complex permittivity) as a complementary method for detecting polyps and cancer tissue in the colon. The dielectric properties of biological tissues have been used in a wide variety of applications, including safety assessment of wireless technologies and design of medical diagnostic or therapeutic techniques (microwave imaging, hyperthermia, and ablation). The main purpose of this work is to measure the complex permittivity of different types of colon polyps, cancer, and normal mucosa in ex vivo human samples to study if the dielectric properties are appropriate for classification purposes. Methods: The complex permittivity of freshly excised healthy colon tissue, cancer, and histological samples of different types of polyps from 23 patients was characterized using an open-ended coaxial probe between 0.5 and 20 GHz. The obtained measurements were classified into five tissue groups before applying a data reduction step with a frequency dispersive single-pole Debye model. The classification was finally compared with pathological analysis of tissue samples, which is the gold standard. Results: The complex permittivity progressively increases as the tissue degenerates from normal to cancer. When comparing to the gold-standard histological tissue analysis, the sensitivity and specificity of the proposed method is the following: 100% and 95% for cancer diagnosis; 91% and 62% for adenomas with high-grade dysplasia; 100% and 61% for adenomas with low-grade dysplasia; and 100% and 74% for hyperplastic polyps, respectively. In addition, complex permittivity measurements were independent of the lesion shape and size, which is also an interesting property comparing to current colonoscopy techniques. Conclusions: The contrast in complex permittivities between normal and abnormal colon tissues presented here for the first time demonstrate the potential of these measurements for tissue classification. It also opens the door to the development of a microwave endoscopic device to complement the outcomes of colonoscopy with functional tissue information., This work was supported by the Department of Universitats, Recerca i Societat de la Informacio of the Catalan Government through Llavor 2014LLAV00016 and producte 2016PROD00068 projects, La Caixa through Caixaimpulse program CI16-00058, the Spanish Comision Interministerial de Ciencia y Tecnologıa (CICYT) under projects TEC2016- 78028-C3-1-P, TEC2014-58582-R, the Spanish Agencia Estatal de Investigacion Unidad de Excelencia Maria de Maeztu (MDM-2016-0600), the Spanish Ministerio de Economıa, Industria y Competitividad, DTS17/00090 and CERCA Programme/Generalitat de Catalunya.
Repositorio Digital de la UPF
Publicación Artículo científico (JournalArticle)

Laparoscopic partial splenectomy for giant cyst using a radiofrequency-assisted device: a case report

  • Quesada Diez, Rita
  • Poves Prim, José Ignacio
  • Iglesias Coma, Mar
  • Berjano, Enrique J.
  • Grande Posa, Luís
  • Burdío Pinilla, Fernando
Background: Although radiofrequency-assisted devices have sometimes been used in partial splenectomy, this is not a common technique. This report describes the first case of laparoscopic partial splenectomy using an RF-assisted device (Coolinside) which allows both coagulation and transection of the parenchyma and eventually the protective coagulation of the remnant side. Case presentation: A 27-year-old woman was found to have a giant hydatic cyst measuring 12.0 × 14.0 × 16.6 cm that mainly occupied the lower pole of the spleen and retroperitoneal space. The patient underwent a laparoscopic partial splenectomy using an RF-based device designed to accomplish both the coagulation and dissection of the splenic tissue. The estimated blood loss was less than 200 mL. Conclusions: Even though RF ablation has traditionally been used for hepatic parenchymal transection, it seems equally suited to partial splenectomy. This device seems to provide good results, minimizing blood loss during partial splenectomy; however, randomized trials will be necessary to see if the results are superior to those of other techniques., This work was partially supported by the Spanish “Programa Estatal de Investigación, Desarrollo e Innovación Orientada a los Retos de la Sociedad” under Grant TEC2014-52383-C3-R (TEC2014-52383-C3-1-R and TEC2014-52383-C3-3-R).
Repositorio Digital de la UPF
Publicación Artículo científico (JournalArticle)

Focused transhepatic electroporation mediated by hypersaline infusion through the portal vein in rat model: Preliminary results on differential conductivity

  • Pañella Vilamú, Clara, 1987-
  • Castellví Fernández, Quim
  • Moll, Xavier
  • Quesada Diez, Rita
  • Villanueva, Alberto
  • Iglesias Coma, Mar
  • Naranjo‐Hans, Dolores
  • Sánchez Velázquez, Patricia, 1985-
  • Andaluz, Anna
  • Grande Posa, Luís
  • Ivorra Cano, Antoni, 1974-
  • Burdío Pinilla, Fernando
Background. Spread hepatic tumours are not suitable for treatment either by surgery or conventional ablation methods. The aim of this study was to evaluate feasibility and safety of selectively increasing the healthy hepatic conductivity by the hypersaline infusion (HI) through the portal vein. We hypothesize this will allow simultaneous safe treatment of all nodules by irreversible electroporation (IRE) when applied in a transhepatic fashion. Material and methods. Sprague Dawley (Group A, n = 10) and Athymic rats with implanted hepatic tumour (Group B, n = 8) were employed. HI was performed (NaCl 20%, 3.8 mL/Kg) by trans-splenic puncture. Deionized serum (40 mL/Kg) and furosemide (2 mL/Kg) were simultaneously infused through the jugular vein to compensate hypernatremia. Changes in conductivity were monitored in the hepatic and tumour tissue. The period in which hepatic conductivity was higher than tumour conductivity was defined as the therapeutic window (TW). Animals were monitored during 1-month follow-up. The animals were sacrificed and selective samples were used for histological analysis. Results. The overall survival rate was 82.4% after the HI protocol. The mean maximum hepatic conductivity after HI was 2.7 and 3.5 times higher than the baseline value, in group A and B, respectively. The mean maximum hepatic conductivity after HI was 1.4 times higher than tumour tissue in group B creating a TW to implement selective IRE. Conclusions. HI through the portal vein is safe when the hypersaline overload is compensated with deionized serum and it may provide a TW for focused IRE treatment on tumour nodules., This work received financial support from the Spanish Government (Ministry of Economy and Competitiveness) under Grant TEC2014-52383-C3. The authors disclose no conflicts of interests.
Repositorio Digital de la UPF
Publicación Artículo científico (JournalArticle)

Long-term effectiveness of irreversible electroporation in a murine model of colorectal liver metastasis

  • Ivorra Cano, Antoni, 1974-
  • Sánchez Velázquez, Patricia, 1985-
  • Castellví Fernández, Quim
  • Villanueva, Alberto
  • Iglesias Coma, Mar
  • Quesada Diez, Rita
  • Pañella Vilamú, Clara, 1987-
  • Cáceres Aguilar, Mario
  • Dorcaratto, Dimitri
  • Andaluz, Anna
  • Moll, Xavier
  • Burdío, José M.
  • Grande Posa, Luís
  • Burdío Pinilla, Fernando
Irreversible electroporation (IRE) has recently gained in popularity as an ablative technique, however little is known about its oncological long-term outcomes. To determine the long-time survival of animals treated with a high dose of IRE and which histological changes it induces in tumoral tissue, IRE ablation was performed in forty-six athymic-nude mice with KM12C tumors implanted in the liver by applying electric current with different voltages (2000 V/cm, 1000 V/cm). The tumors were allowed to continue to grow until the animals reached the end-point criteria. Histology was harvested and the extent of tumor necrosis was semi-quantitatively assessed. IRE treatment with the 2000 V/cm protocol significantly prolonged median mouse survival from 74.3 ± 6.9 days in the sham group to 112.5 ± 15.2 days in the 2000 V/cm group. No differences were observed between the mean survival of the 1000 V/cm and the sham group (83.2 ± 16.4 days, p = 0.62). Histology revealed 63.05% ± 23.12 of tumor necrosis in animals of the 2000 V/cm group as compared to 17.50% ± 2.50 in the 1000 V/cm group and 25.6% ± 22.1 in the Sham group (p = 0.001). IRE prolonged the survival of animals treated with the highest electric field (2000 V/cm). The animals in this group showed significantly higher rate of tumoral necrosis., This research was supported by the spanish government under grants TEC2011-27133-c02 and TEC2010-17285, and by the spanish “plan estatal de investigación, desarrollo e innovación orientada a los retos de la sociedad” under grant TEC2014–52383-c3-r (TEC2014–52383-c3-2-r and TEC2014–52383-c3-3-r).
Repositorio Digital de la UPF
Publicación Artículo científico (JournalArticle)

Development of a catheter-based technique for endoluminal radiofrequency sealing of pancreatic duct

  • Ewertowska, Elżbieta
  • Andaluz, Anna
  • Moll, Xavier
  • Aguilar, Adrià
  • Garcia, Felix
  • Fondevila, Dolors
  • Quesada Diez, Rita
  • Trujillo Guillén, Macarena
  • Burdío Pinilla, Fernando
  • Berjano, Enrique J.
introduction: Endoluminal sealing of the pancreatic duct by glue or sutures facilitates the management of the pancreatic stump. Our objective was to develop a catheter-based alternative for endoluminal radiofrequency (RF) sealing of the pancreatic duct. Materials and methods: We devised a novel RF ablation technique based on impedance-guided catheter pullback. First, bench tests were performed on ex vivo models to tune up the technique before the in vivo study, after which endoluminal RF sealing of a ∼10 cm non-transected pancreatic duct was conducted on porcine models using a 3 Fr catheter. After 30 days, sealing effectiveness was assessed by a permeability test and a histological analysis. Results: The RF technique was feasible in all cases and delivered ∼5 W of power on an initial impedance of 308 ± 60 Ω. Electrical impedance evolution was similar in all cases and provided guidance for modulating the pullback speed to avoid tissue sticking and achieve a continuous lesion. During the follow-up the animals rate of weight gain was significantly reduced (p < 0.05). Apart from signs of exocrine atrophy, no other postoperative complications were found. At necropsy, the permeability test failed and the catheter could not be reintroduced endoluminally, confirming that sealing had been successful. The histological analysis revealed a homogeneous exocrine atrophy along the ablated segment in all the animals. Conclusions: Catheter-based RF ablation could be used effectively and safely for endoluminal sealing of the pancreatic duct. The findings suggest that a fully continuous lesion may not be required to obtain complete exocrine atrophy., This work was supported by the Spanish Ministerio de Economía, Industria y Competitividad under “Plan Estatal de Investigación, Desarrollo e Innovación Orientada a los Retos de la Sociedad” (Grant TEC2014–52383–C3–R) and by the Spanish Ministerio de Ciencia, Innovación y Universidades under “Programa Estatal de I + D + i Orientada a los Retos de la Sociedad" (Grant: RTI2018-094357-B-C21 and –C22). Elżbieta Ewertowska has a Predoctoral Grant (BES-2015–073285) from the Ministry of Economy, Industry and Competitiveness (Government of Spain). Also funding was received from Secretaría de Estado de Investigación, Desarrollo e Innovación.
Repositorio Digital de la UPF
Publicación Artículo científico (JournalArticle)

Dynamics of cell death after conventional IRE and H-FIRE treatments

  • Mercadal, Borja
  • Beitel White, Natalie
  • Aycock, Kenneth N.
  • Castellví Fernández, Quim
  • Davalos, Rafael Vidal
  • Ivorra Cano, Antoni, 1974-
High-frequency irreversible electroporation (H-FIRE) has emerged as an alternative to conventional irreversible electroporation (IRE) to overcome the issues associated with neuromuscular electrical stimulation that appear in IRE treatments. In H-FIRE, the monopolar pulses typically used in IRE are replaced with bursts of short bipolar pulses. Currently, very little is known regarding how the use of a different waveform affects the cell death dynamics and mechanisms. In this study, human pancreatic adenocarcinoma cells were treated with a typical IRE protocol and various H-FIRE schemes with the same energized time. Cell viability, membrane integrity and Caspase 3/7 activity were assessed at different times after the treatment. In both treatments, we identified two different death dynamics (immediate and delayed) and we quantified the electric field ranges that lead to each of them. While in the typical IRE protocol, the electric field range leading to a delayed cell death is very narrow, this range is wider in H-FIRE and can be increased by reducing the pulse length. Membrane integrity in cells suffering a delayed cell death shows a similar time evolution in all treatments, however, Caspase 3/7 expression was only observed in cells treated with H-FIRE., This work was supported by the Ministry of Economy and Competitiveness of Spain (Grant No. TEC2014-52383-C3-2-R), the Pancreatic Cancer Action Network (Grant No. 16-65-IANN) and Cures Within Reach (Grant No. PUJFSANY). Antoni Ivorra gratefully acknowledges financial support by ICREA under the ICREA Academia programme.
Repositorio Digital de la UPF
Publicación Artículo científico (JournalArticle)

Modeling methods for treatment planning in overlapping electroporation treatments

  • Perera Bel, Enric
  • Mercandal, Borja
  • Garcia-Sanchez, Tomas
  • González Ballester, Miguel Ángel, 1973-
  • Ivorra Cano, Antoni, 1974-
Objective: Irreversible electroporation (IRE) is a non thermal tissue ablation therapy which is induced by applying high voltage waveforms across electrode pairs. When multiple electrode pairs are sequentially used, the treatment volume (TV) is typically computed as the geometric union of the TVs of individual pairs. However, this method neglects that some regions are exposed to overlapping treatments. Recently, a model describing cell survival probability was introduced which effectively predicted TV with overlapping fields in vivo. However, treatment overlap has yet to be quantified. This study characterizes TV overlap in a controlled in vitro setup with the two existing methods which are compared to an adapted logistic model proposed here. Methods: CHO cells were immobilized in agarose gel. Initially, we characterized the electric field threshold and the cell survival probability for overlapping treatments. Subsequently, we created a 2D setup where we compared and validated the accuracy of the different methods in predicting the TV. Results: Overlap can reduce the electric field threshold required to induce cell death, particularly for treatments with low pulse number. However, it does not have a major impact on TV in the models assayed here, and all the studied methods predict TV with similar accuracy. Conclusion: Treatment overlap has a minor influence in the TV for typical protocols found in IRE therapies. Significance: This study provides evidence that the modeling method used in most pre-clinical and clinical studies seems adequate.
Repositorio Digital de la UPF
Publicación Artículo científico (JournalArticle)

Avoiding nerve stimulation in irreversible electroporation: a numerical modeling study

  • Mercadal, Borja
  • Arena, Christopher B.
  • Davalos, Rafael Vidal
  • Ivorra Cano, Antoni, 1974-
Electroporation based treatments consist in applying one or multiple high voltage pulses to the tissues to be treated. As an undesired side effect, these pulses cause electrical stimulation of excitable tissues such as nerves and muscles. This increases the complexity of the treatments and may pose a risk to the patient. To minimize electrical stimulation during electroporation based treatments, it has been proposed to replace the commonly used monopolar pulses by bursts of short bipolar pulses. In the present study, we have numerically analyzed the rationale for such approach. We have compared different pulsing protocols in terms of their electroporation efficacy and their capability to trigger action potentials in nerves. For that, we have developed a modeling framework that combines numerical models of nerve fibers and experimental data on irreversible electroporation. Our results indicate that, by replacing the conventional relatively long monopolar pulses by bursts of short bipolar pulses, it is possible to ablate a large tissue region without triggering action potentials in a nearby nerve. Our models indicate that this is possible because, as the pulse length of these bipolar pulses is reduced, the stimulation thresholds raise faster than the irreversible electroporation thresholds. We propose that this different dependence on the pulse length is due to the fact that transmembrane charging for nerve fibers is much slower than that of cells treated by electroporation because of their geometrical differences., This work was supported by the Ministry of Economy and Competitiveness of Spain through the grant TEC2014-52383-C3-2-R. RVD’s research is supported by the National Institutes of Health under award number NIH 1R21 CA192041-01.
Repositorio Digital de la UPF
Publicación Artículo científico (JournalArticle)

Pulsed radiofrequency for chronic pain: In vitro evidence of an electroporation mediated calcium uptake

  • Mercadal, Borja
  • Vicente García, Rubén, 1978-
  • Ivorra Cano, Antoni, 1974-
Pulsed radiofrequency (PRF) treatments for chronic pain consist in the delivery of a train of sinusoidal electric bursts to the targeted nerve. Despite numerous clinical evidence of its efficiency, the mechanism of action of PRF remains unclear. Since most of the reported biological effects of PRF can be initiated by a calcium influx into the neurons, we hypothesized that PRF may induce a mild electroporation effect causing a calcium uptake. To test this hypothesis, HEK-293 cells were exposed to PRF bursts and cytosolic calcium and Yo-Pro-1 uptake were monitored. After a single burst, calcium peaks were observed for electric fields above 480 V/cm while the uptake of Yo-pro-1 was insignificant. After a train of 120 bursts, the electric fields required to induce a calcium and Yo-pro-1 uptake decreased to 330 V/cm and 880 V/cm respectively. Calcium peaks were not detected when cells were treated in calcium free media. The temperature increase during the treatments was lower than 5 °C in all cases. Finally, the cell response for different burst frequencies and extracellular media conductivities correlated with the induced transmembrane voltage calculated with a numerical model. Our results support the hypothesis of an electroporation mediated calcium influx., This work was supported by the Ministry of Economy and Competitiveness of Spain through the grants TEC2014-52383-C3-2-R and SAF2014-52228-R. Antoni Ivorra gratefully acknowledges the financial support by ICREA under the ICREA Academia programme.
Repositorio Digital de la UPF
Publicación Artículo científico (JournalArticle)

Anatomically realistic simulations of liver ablation by irreversible electroporation: impact of blood vessels on ablation volumes and undertreatment

  • Ivorra Cano, Antoni, 1974-
  • Qasrawi, Radwan Fayez Hasan
  • Silve, Louis Charles Arthur
  • Burdío Pinilla, Fernando
  • Abdeen, Ziad
Irreversible electroporation is a novel tissue ablation technique which entails delivering intense electrical pulses to target tissue, hence producing fatal defects in the cell membrane. The present study numerically analyzes the potential impact of liver blood vessels on ablation by irreversible electroporation because of their influence on the electric field distribution. An anatomically realistic computer model of the liver and its vasculature within an abdominal section was employed, and blood vessels down to 0.4 mm in diameter were considered. In this model, the electric field distribution was simulated in a large series of scenarios (N = 576) corresponding to plausible percutaneous irreversible electroporation treatments by needle electrode pairs. These modeled treatments were relatively superficial (maximum penetration depth of the electrode within the liver = 26 mm) and it was ensured that the electrodes did not penetrate the vessels nor were in contact with them. In terms of total ablation volume, the maximum deviation caused by the presence of the vessels was 6%, which could be considered negligible compared to the impact by other sources of uncertainty. Sublethal field magnitudes were noticed around vessels covering volumes of up to 228 mm3. If in this model the blood was substituted by a liquid with a low electrical conductivity (0.1 S/m), the maximum volume covered by sublethal field magnitudes was 3.7 mm3 and almost no sublethal regions were observable. We conclude that undertreatment around blood vessels may occur in current liver ablation procedures by irreversible electroporation. Infusion of isotonic low conductivity liquids into the liver vasculature could prevent this risk., This work received financial support from the Spanish Government through grants TEC2010-17285, TEC2011-27133-C02, and TEC2014-52383-C3 (TEC2014-52383-C3-2) and from the European Commission through the Marie Curie IRG grant “TAMIVIVE” 256376.
Repositorio Digital de la UPF
Publicación Contribución de congreso (ConferenceOutput)

Modeling liver electrical conductivity during hypertonic injection

  • Castellví Fernández, Quim
  • Sánchez Velázquez, Patricia, 1985-
  • Moll, Xavier
  • Berjano, Enrique J.
  • Andaluz, Anna
  • Burdío Pinilla, Fernando
  • Bijnens, Bart
  • Ivorra Cano, Antoni, 1974-
Metastases in the liver frequently grow as scattered tumor nodules which neither can be removed by surgical resection nor focally ablated. Previously, we have proposed a novel technique based on irreversible electroporation which may be able to simultaneously treat all nodules in the liver while sparing healthy tissue. The proposed technique requires increasing the electrical conductivity of healthy liver by injecting a hypersaline solution through the portal vein. Aiming to assess the capability of increasing the global conductivity of the liver by means of hypersaline fluids, here it is presented a mathematical model which estimates the NaCl distribution within the liver and the resulting conductivity change. The model fuses wellestablished compartmental pharmacokinetic models of the organ with saline injection models employed for resuscitation treatments and it considers changes in sinusoidal blood viscosity due to the hypertonicity of the solution. Here it is also described a pilot experimental study in pigs in which different volumes of NaCl 20% (from 100 to 200 ml) were injected through the portal vein at different flow rates (from 53 to 171 ml/min). The in vivo conductivity results fit those obtained by the model, both quantitatively and qualitatively, being able to predict the maximum conductivity with a 14.6% average relative error. The maximum conductivity value was 0.44 S/m which corresponds to increasing four times the mean basal conductivity (0.11 S/m). The results suggest that the presented model is well suited for predicting on liver conductivity changes during hypertonic saline injection., Spanish Government; contract/grant number: TEC2014-52383-C3-1-R, TEC2014-52383-C3-2-R and TEC2014-52383-C3-3-R
Repositorio Digital de la UPF
Publicación Contribución de congreso (ConferenceOutput)

Charge counter for performing active charge-balance in miniaturized electrical stimulators

  • Becerra Fajardo, Laura
  • Ivorra Cano, Antoni, 1974-
Functional Electrical Stimulation (FES) has been explored in order to restore the capabilities of the nervous system in patients that suffer from paralysis. This area of research and of clinical practice greatly benefits from any technological improvement yielding miniaturization. In this regard, we recently proposed and demonstrated an innovative electrical stimulation method based on implanted microstimulators that operate as rectifiers of bursts of innocu-ous high frequency current supplied by skin electrodes, gener-ating low frequency currents that are capable of stimulating excitable tissues. We envision flexible ultrathin implants (di-ameters < 300 μm) containing ASICs that have advanced ca-pabilities, such as addressability and current control. As min-iaturization is the main aim of this method, the use of bulky DC-blocking capacitors (e.g. 10 μF) to accomplish zero net charge injection and avoid electrochemical tissue and electrode damage is highly inconvenient. As an alternative, here we present an active charge-balance method based on the use of a digital charge quantifier, whose operation is inspired in the functioning of the tipping bucket rain gauge. The system moni-tors the charge injection, matching the charge injected in the cathodal phase, with the charge injected in the anodal phase, generating a biphasic current waveform that adapts itself to possible current source mismatches. We have implemented a prototype built with discrete components which uses a capaci-tor of only 100 pF for the charge counter., AI’s research is supported by a Ramón y Cajal fellowship/nfrom the Spanish government and a Marie Curie grant/n(IRG 256376) from the European Commission. LBF’s research/nis supported by a scholarship from the UPF.
Repositorio Digital de la UPF
Publicación Artículo científico (JournalArticle)

Electrical modeling of the influence of medium conductivity on electroporation

  • Ivorra Cano, Antoni, 1974-
  • Villemejane, Julien
  • Mir, Lluis M.
Electroporation is the phenomenon in which cell membrane permeability is increased by exposing the cell to short high electric field pulses. Experimental data show that the amount of permeabilization depends on the conductivity of the extracellular medium. If medium conductivity decreases then it is necessary to deliver a pulse of larger field amplitude in order to achieve the same effect. Models that do not take into account the permeabilization effect on the membrane conductivity cannot reproduce qualitatively the experimental observations. Here we employ an exponential function for describing the strong dependence of membrane conductivity on transmembrane potential. Combining that model with numerical methods we demonstrate that the dependence on medium conductivity can be explained as being the result of increased membrane conductance due to electroporation. As experimentally observed, extracellular conductivities of about 1 and 0.1 S m−1 yield very similar results, however, for lower conductivities (<0.01 S m−1) the model predicts that significantly higher field magnitudes will be required to achieve the same amount of permeabilization., This work was supported by grants from: CNRS, Institute of cancerology Gustave-Roussy, University Paris Sud, INCa (National Institute of Cancer, France—contract number 07/3D1616/Doc-54-3NG-NC) and French National Agency (ANR) through Nanoscience and Nanotechnology program (Nanopulsebiochip no. ANR-08-NANO-024). AI’s research is currently supported by a Ramon y Cajal/nfellowship from the Spanish Ministry for Science and Innovation.
Repositorio Digital de la UPF
Publicación Artículo científico (JournalArticle)

Impact of monopolar radiofrequency coagulation on intraoperative blood loss during liver resection: a prospective randomised controlled trial

  • Quesada Diez, Rita
  • Poves Prim, José Ignacio
  • Berjano, Enrique J.
  • Vilaplana, Carles
  • Andaluz, Anna
  • Moll, Xavier
  • Dorcaratto, Dimitri
  • Grande Posa, Luís
  • Burdío Pinilla, Fernando
PURPOSE: To evaluate the impact of using monopolar thermal coagulation based on radiofrequency (RF) currents on intraoperative blood loss during liver resection. MATERIALS AND METHODS: A prospective randomised controlled trial was planned. Patients undergoing hepatectomy were randomised into two groups. In the control group (n = 10), hemostasis was obtained with a combination of stitches, vessel-sealing bipolar RF systems, sutures or clips. In the monopolar radiofrequency coagulation (MRFC) group (n = 18), hemostasis was mainly obtained using an internally cooled monopolar RF electrode. RESULTS: No differences in demographic or clinical characteristics were found between groups. Mean blood loss during liver resection in the control group was more than twice that of the MRFC group (556 ± 471 ml vs. 225 ± 313 ml, p = .02). The adjusted mean bleeding/transection area was also significantly higher in the control group (7.0 ± 3.3 ml/cm2 vs. 2.8 ± 4.0 ml/cm2, p = .006). No significant differences were observed in the rate of complications between the groups. CONCLUSIONS: The findings suggest that the monopolar electrocoagulation created with an internally cooled RF electrode considerably reduces intraoperative blood loss during liver resection., This work was supported by a medical research grant from the Spanish Government (FIS PI080934) and by Spanish “Programa Estatal de Investigación, Desarrollo e Innovación Orientada a los Retos de la Sociedad” under Grant TEC2014–52383-C3-R (TEC2014–52383-C3–1-R and TEC2014–52383-C3–3-R)
Repositorio Digital de la UPF
Publicación Artículo científico (JournalArticle)

EView: an electric field visualization web platform for electroporation-based therapies

  • Perera Bel, Enric
  • Yagüe, Carlos
  • Mercadal, Borja
  • Ceresa, Mario
  • Beitel White, Natalie
  • Davalos, Rafael Vidal
  • González Ballester, Miguel Ángel, 1973-
  • Ivorra Cano, Antoni, 1974-
Background and objectives: Electroporation is the phenomenon by which cell membrane permeability to ions and macromolecules is increased when the cell is briefly exposed to high electric fields. In electroporation-based treatments, such exposure is typically performed by delivering high voltage pulses across needle electrodes in tissue. For a given tissue and pulsing protocol, an electric field magnitude threshold exists that must be overreached for treatment efficacy. However, it is hard to preoperatively infer the treatment volume because the electric field distribution intricately depends on the electrodes’ positioning and length, the applied voltage, and the electric conductivity of the treated tissues. For illustrating such dependencies, we have created EView (https://eview.upf.edu), a web platform that estimates the electric field distribution for arbitrary needle electrode locations and orientations and overlays it on 3D medical images. Methods: A client-server approach has been implemented to let the user set the electrode configuration easily on the web browser, whereas the simulation is computed on a dedicated server. By means of the finite element method, the electric field is solved in a 3D volume. For the sake of simplicity, only a homogeneous tissue is modeled, assuming the same properties for healthy and pathologic tissues. The non-linear dependence of tissue conductivity on the electric field due to the electroporation effect is modeled. The implemented model has been validated against a state of the art finite element solver, and the server has undergone a heavy load test to ensure reliability and to report execution times. Results: The electric field is rapidly computed for any electrode and tissue configuration, and alternative setups can be easily compared. The platform provides the same results as the state of the art finite element solver (Dice = 98.3 ± 0.4%). During the high load test, the server remained responsive. Simulations are computed in less than 2 min for simple cases consisting of two electrodes and take up to 40 min for complex scenarios consisting of 6 electrodes. Conclusions: With this free platform we provide expert and non-expert electroporation users a way to rapidly model the electric field distribution for arbitrary electrode configurations., This work was supported by the Ministry of Economy and Competitiveness of Spain (grant number TEC2014-52383-C3-2-R), the María de Maeztu Units of Excellence Programme (grant number MDM-2015-0502) and by the Spanish Ministry of Economy and Competitiveness under the Programme for the Formation of Doctors (grant number BES-2017-081164). Antoni Ivorra gratefully acknowledges the financial support by ICREA under the ICREA Academia programme.
Repositorio Digital de la UPF
Publicación Artículo científico (JournalArticle)

Dependence of electroporation detection threshold on cell radius: an explanation to observations non compatible with Schwan’s equation model

  • Mercadal, Borja
  • Vernier, P. Thomas
  • Ivorra Cano, Antoni, 1974-
It is widely accepted that electroporation occurs when the cell transmembrane voltage induced by an external applied electric field reaches a threshold. Under this assumption, in order to trigger electroporation in a spherical cell, Schwan’s equation leads to an inversely proportional relationship between the cell radius and the minimum magnitude of the applied electric field. And, indeed, several publications report experimental evidences of an inverse relationship between the cell size and the field required to achieve electroporation. However, this dependence is not always observed or is not as steep as predicted by Schwan’s equation. The present numerical study attempts to explain these observations that do not fit Schwan’s equation on the basis of the interplay between cell membrane conductivity, permeability, and transmembrane voltage. For that, a single cell in suspension was modeled and the electric field necessary to achieve electroporation with a single pulse was determined according to two effectiveness criteria: a specific permeabilization level, understood as the relative area occupied by the pores during the pulse, and a final intracellular concentration of a molecule due to uptake by diffusion after the pulse, during membrane resealing. The results indicate that plausible model parameters can lead to divergent dependencies of the electric field threshold on the cell radius. These divergent dependencies were obtained through both criteria and using two different permeabilization models. This suggests that the interplay between cell membrane conductivity, permeability, and transmembrane voltage might be the cause of results which are noncompatible with the Schwan’s equation model., This work was supported by the Ministry of Economy and Competitiveness of Spain through Grant TEC2014-52383-C3-2-R. PTV received support from the Old Dominion University Frank Reidy Research Center for Bioelectrics and the Air Force Office of Scientific Research (FA9550-15-1-0517, FA9550-14-1-0123).
Repositorio Digital de la UPF
Publicación Artículo científico (JournalArticle)

Endoluminal radiofrequency ablation of the main pancreatic duct is a secure and effective method to produce pancreatic atrophy and to achieve stump closure

  • Andaluz, Anna
  • Ewertowska, Elżbieta
  • Moll, Xavier
  • Aguilar, Adrià
  • García Arnas, Félix
  • Fondevila, Dolors
  • Quesada Diez, Rita
  • Berjano, Enrique J.
  • Grande Posa, Luís
  • Burdío Pinilla, Fernando
Radiofrequency energy has been used both experimentally and clinically to manage the pancreatic remnant after distal pancreatectomies. Our goal was to determine whether endoluminal radiofrequency (RF) ablation of the main pancreatic duct in large animals would be more efficient than glue occlusion as an exocrine pancreatic atrophy-inducing procedure. Thirty-four Landrace pigs were assigned to either the transpapilar (n = 16) or transection (n = 18) groups. The transection implied the pancreas neck was severed. In each of these groups the remaining distal pancreatic duct was occluded either by RF or by glue. In the transpapilar group complete atrophy was observed in all the RF cases, while atrophy was incomplete in all the members of the glue subgroup. The failure rate of the main pancreatic duct (usually expressed by a pseudocyst) in the transection groups was dramatically higher in the glue subgroup than the RF subgroups (9 out of 9 and 1 out of 9, respectively) and postoperative mortality occurred only in the glue subgroup (3 out of 9). These results show the superiority of endoluminal RF ablation over glue for main pancreatic duct occlusion, as seen by the degree of atrophy and fewer postoperative pancreatic fistulas., This work was supported by the Spanish Ministerio de Economía, Industria y Competitividad under the “Plan Estatal de Investigación, Desarrollo e Innovación Orientada a los Retos de la Sociedad” Grant TEC2014–52383–C3–R (TEC2014–52383–C3–1–R and TEC2014–52383–C3–3–R). Elzbieta Ewertowska has a Predoctoral Grant (BES-2015–073285) from the Ministry of Economy, Industry and Competitiveness (Government of Spain).
Repositorio Digital de la UPF
Publicación Artículo científico (JournalArticle)

Avoiding neuromuscular stimulation in liver irreversible electroporation using radiofrequency electric fields

  • Castellví Fernández, Quim
  • Mercadal, Borja
  • Moll, Xavier
  • Fondevila, Dolors
  • Andaluz, Anna
  • Ivorra Cano, Antoni, 1974-
Electroporation based treatments typically consist in applying high voltage dc pulses. As an undesired side effect, these dc pulses cause electrical stimulation of excitable tissues such as motor nerves. In the present in vivo study, it was explored the use of bursts of sinusoidal voltage in the frequency range from 50 kHz to 2 MHz to induce irreversible electroporation (IRE) whilst avoiding neuromuscular stimulation. Series of 100 dc pulses or sinusoidal bursts, both with an individual duration of 100 μs, were delivered to rabbit liver through thin needles in a monopolar electrode configuration and thoracic movements were recorded with an accelerometer. Tissue samples were harvested three hours after treatment and later postprocessed to determine the dimensions of the IRE lesions. Thermal damage due to Joule heating was ruled out via computer simulations. Sinusoidal bursts with a frequency equal or above 100 kHz did not cause thoracic movements and induced lesions equivalent to those obtained with conventional dc pulses when the applied voltage amplitude was sufficiently high. IRE efficacy dropped with increasing frequency. For 100 kHz bursts, it was estimated that the electric field threshold for IRE is about 1.4 kV/cm whereas that of dc pulses is about 0.5 kV/cm., This work was supported by the Ministry of Economy and Competitiveness of Spain through the grant TEC2014-52383-C3-R (TEC2014-52383-C3-2-R and TEC2014-52383-C3-3-R).
Repositorio Digital de la UPF
Publicación Artículo científico (JournalArticle)

Electrochemical prevention of needle-tract seeding

  • Ivorra Cano, Antoni, 1974-
Needle-tract seeding refers to the implantation of tumor cells by contamination when instruments, such as biopsy needles, are employed to examine, excise or ablate a tumor. The incidence of this iatrogenic phenomenon is low but it entails serious consequences. Here, as a new method for preventing neoplasm seeding, it is proposed to cause electrochemical reactions at the instrument surface so that a toxic microenvironment is formed. In particular, the instrument shaft would act as the cathode and the tissues would act as the electrolyte in an electrolysis cell. By employing numerical models and experimental observations reported by researchers on Electrochemical Treatment of tumors, it is numerically showed that a sufficiently toxic environment of supraphysiological pH can be created in a few seconds without excessive heating. Then, by employing an ex vivo model consisting of meat pieces, validity of the conclusions provided by the numerical model concerning pH evolution is confirmed. Furthermore, a simplified in vitro model based on bacteria, instead of tumor cells, is implemented for showing the plausibility of the method. Depending on the geometry of the instrument, suitable current densities will probably range from about 5 mA/cm2 to 200 mA/cm2 and the duration of DC current delivery will range from a few seconds to a few minutes., AI’s research is currently supported by a Ramón y Cajal fellowship from the Spanish Ministry for Science and Innovation.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Contribución de congreso (ConferenceOutput)

Initial UWB in-body channel characterization using a novel multilayer phantom measurement setup

  • Pérez-Simbor, Sofia
  • Barbi, Martina
  • Garcia-Pardo, Concepcion|||0000-0002-2774-980X
  • Castelló-Palacios, Sergio|||0000-0003-4689-652X
  • Cardona Marcet, Narciso|||0000-0001-5697-1453
[EN] Wireless Body Area Networks (WBANs) are a promising technology for medical purposes. Currently the WBAN are classified into: implanted (in-), surface (on-) or outside (off-) body communications regarding the location of the devices with reference to the human body. The Ultra Wide-Band (UWB) frequency band is growing as a band of interest for implanted communications because of its high data rate and low power consumption among other benefits. Software simulations, in-vivo measurements and experimental phantom measurements are common methods to properly characterize the propagation channel. Nevertheless, up to now, experimental phantoms measurements presented in the literature show some inconveniences, i.e., the accuracy of the phantoms compared with the real human tissues or the testbed used for the measurements. This paper aims at overcoming these issues using accurate phantoms designed for the purpose of implanted communications in the UWB frequency band. In addition, a multilayer phantom container was developed. This container has capacity for two different phantoms, emulating a heterogeneous propagation medium for in-body measurements. Moreover, a novel setup was built for in-body phantom measurements. As a result, an experimental path loss model is presented from the measurements obtained with phantoms. Besides, software simulations mimicking the experimental setup are performed in order to validate the previous results obtained, This work was supported by the European Union's H2020:MSCA:ITN program for the "Wireless In-body Environment Communication-WiBEC" project under the grant agreement no. 675353. this work was also funded by the Programa de Ayudas de Investigación y Desarrollo 8PAID-01-16) from Univeristat Politècnica de València and by the Ministerio de Economía y Competitividad, Spain (TEC2014-60258-C2-1-R), by the European FEDER funds.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Simulating Opportunistic Networks: Survey and Future Directions

  • Dede, Jens
  • Förster, Anna
  • Herrera-Tapia, Jorge
  • Kuladinithi, Koojana
  • Kuppusamy, Vishnupriya
  • bin Muslim, Anas
  • Udugama, Asanga
  • Vatandas, Zeynep
  • Hernández-Orallo, Enrique|||0000-0002-3284-561X
  • Manzoni, Pietro|||0000-0003-3753-0403
[EN] Simulation is one of the most powerful tools we have for evaluating the performance of opportunistic networks (OppNets). In this paper, we focus on available tools and mod- els, compare their performance and precision and experimentally show the scalability of different simulators. We also perform a gap analysis of state-of-the-art OppNet simulations and sketch out possible further development and lines of research. This paper is targeted at students starting work and research in this area while also serving as a valuable source of information for experienced researchers., This work was supported in part by the Ministerio de Economia y Competitividad, Programa Estatal de Investigacion, Desarrollo e Innovacion Orientada a los Retos de la Sociedad, Proyectos I+D+I 2014, Spain, under Grant TEC2014-52690-R, in part by the Universidad Laica Eloy Alfaro de Manabi, and in part by the Secretaria Nacional de Educacion Superior, Ciencia, Tecnologia e Innovacion, Ecuador. (Corresponding author: Jens Dede.)
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Fano resonances and electromagnetically induced transparency in silicon waveguides loaded with plasmonic nanoresonators

  • Ortuño Molinero, Rubén
  • Cortijo-Munuera, Mario
  • Martínez, Alejandro|||0000-0001-5448-0140
The fundamental electric dipolar resonance of metallic nanostrips placed on top of a dielectric waveguide can be excited via evanescent wave coupling, thus giving rise to broad dips in the transmission spectrum of the waveguide. Here we show via numerical simulations that narrower and steeper Fano-like resonances can be obtained by asymmetrically coupling in the near field a larger nanostrip supporting an electric quadrupole in the frequency regime of interest to the original, shorter nanostrip. Under certain conditions, the spectral response corresponding to the electromagnetically induced transparency phenomenon is observed. We suggest that this hybrid plasmonic photonic approach could be especially relevant for sensing or all-optical switching applications in a photonic integrated platform such as silicon photonics., RO acknowledges support from Generalitat Valenciana through the VALi+d postdoctoral program (exp APOSTD/2014/004). AM acknowledges funding from contracts TEC2014-51902-C2-1-R and TEC2014-61906-EXP (MINECO/FEDER, UE) and NANOMET PLUS-PROMETEOII/2014/034 (Conselleria d'Educacio, Cultura i Esport).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Microwave Signal Processing over Multicore Fiber

  • García-Cortijo, Sergi|||0000-0002-7237-9457
  • Barrera Vilar, David|||0000-0002-1700-6842
  • Sales Maicas, Salvador|||0000-0001-9457-976X
  • Gasulla Mestre, Ivana|||0000-0001-8088-7796
  • Hervás-Peralta, Javier
[EN] We review the introduction of the space dimension into fiber-based technologies to implement compact and versatile signal processing solutions for microwave and millimeter wave signals. Built upon multicore fiber links and devices, this approach allows the realization of fiber-distributed signal processing in the context of fiber-wireless communications, providing both radiofrequency access distribution and signal processing in the same fiber medium. We present different space-division multiplexing architectures to implement tunable true time delay lines that can be applied to a variety of microwave photonics functionalities, such as signal filtering, radio beamsteering in phased array antennas or optoelectronic oscillation. In particular, this paper gathers our latest work on the following multicore fiber technologies: dispersion-engineered heterogeneous multicore fiber links for distributed tunable true time delay line operation; multicavity devices built upon the selective inscription of gratings in homogenous multicore fibers for compact true time delay line operation; and multicavity optoelectronic oscillation over both homogeneous and heterogeneous multicore fibers., This research was supported by the ERC Consolidator Grant 724663; the Spanish Projects TEC2015-62520-ERC, TEC2014-60378-C2-1-R and TEC2016-80150-R; the Valencian Research Excellency Award Program GVA PROMETEO 2013/012; the Spanish MECD FPU Scholarship (FPU13/04675) for J. Hervás; the Spanish scholarships MINECO BES-2015-073359 for S. García; and the Spanish MINECO Ramon y Cajal program RYC-2014-16247 for I. Gasulla.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Interrogation of a Sensor Array of Identical Weak FBGs using Dispersive Incoherent OFDR

  • Clement, Juan
  • Torregrosa, German
  • Hervás-Peralta, Javier
  • Fernandez-Pousa, Carlos R.
  • Barrera Vilar, David|||0000-0002-1700-6842
  • Sales Maicas, Salvador|||0000-0001-9457-976X
[EN] Incoherent Optical Fourier-Domain Reflectometry incorporating a dispersive delay line is used for the interrogation of an array of three identical fiber Bragg gratings with a Bragg wavelength of 1552.81 nm, reflectivity of 19.3 dB and 10-cm separation. The dispersive delay line induces different delays in the wavelengths reflected by each grating, thus being sensitive to Bragg wavelength shifts. Compared with conventional incoherent Optical Fourier-Domain Reflectometry, dispersive effects decrease the spatial resolution, which in our experiments reached a value of 1.2 cm in fiber at a measurement bandwidth of 10 GHz. As a quasi-distributed temperature sensor, the array shows an accuracy of ±0.5ºC for temperatures up to 100ºC, and an estimated total measurement range of 540ºC. Tradeoffs between bandwidth, scan time, dispersion-dependent spatial resolution, and accuracy, are also analyzed., This work was supported in part by the Generalitat Valenciana, Valencia, within the Research Excellency Award through the GVA PROMETEO Program under Grant 2013/012 and in part by the Ministerio de Economia y Competitividad under Project TEC201-60378-C2-1-R. The work of J. Hervas was supported by the Ministerio de Educacion, Cultura y Deporte through the Formacion Profesorado Scholarship (FPU13/04675).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Development of a catheter-based technique for endoluminal radiofrequency sealing of pancreatic duct

  • Ewertowska, Elzbieta
  • Andaluz, Anna
  • Moll, Xavier
  • Adrià Aguilar
  • Garcia, Felix
  • Fondevila, Dolors
  • Quesada, Rita
  • Burdio, Fernando
  • Trujillo Guillen, Macarena|||0000-0003-4145-2188
  • Berjano, Enrique|||0000-0002-3247-2665
[EN] Introduction: Endoluminal sealing of the pancreatic duct by glue or sutures facilitates the management of the pancreatic stump. Our objective was to develop a catheter-based alternative for endoluminal radiofrequency (RF) sealing of the pancreatic duct. Materials and methods: We devised a novel RF ablation technique based on impedance-guided catheter pullback. First, bench tests were performed on ex vivo models to tune up the technique before the in vivo study, after which endoluminal RF sealing of a similar to 10 cm non-transected pancreatic duct was conducted on porcine models using a 3 Fr catheter. After 30 days, sealing effectiveness was assessed by a permeability test and a histological analysis. Results: The RF technique was feasible in all cases and delivered similar to 5 W of power on an initial impedance of 308 +/- 60 ohm. Electrical impedance evolution was similar in all cases and provided guidance for modulating the pullback speed to avoid tissue sticking and achieve a continuous lesion. During the follow-up the animals rate of weight gain was significantly reduced (p < 0.05). Apart from signs of exocrine atrophy, no other postoperative complications were found. At necropsy, the permeability test failed and the catheter could not be reintroduced endoluminally, confirming that sealing had been successful. The histological analysis revealed a homogeneous exocrine atrophy along the ablated segment in all the animals. Conclusions: Catheter-based RF ablation could be used effectively and safely for endoluminal sealing of the pancreatic duct. The findings suggest that a fully continuous lesion may not be required to obtain complete exocrine atrophy., This work was supported by the Spanish Ministerio de Economia, Industria y Competitividad under "Plan Estatal de Investigacion, Desarrollo e Innovacion Orientada a los Retos de la Sociedad" (Grant TEC2014-52383-C3-R) and by the Spanish Ministerio de Ciencia, Innovacion y Universidades under "Programa Estatal de I+D+i Orientada a los Retos de la Sociedad" (Grant: RTI2018-094357-B-C21 and -C22). Elzbieta Ewertowska has a Predoctoral Grant (BES-2015-073285) from the Ministry of Economy, Industry and Competitiveness (Government of Spain). Also funding was received from Secretaria de Estado de Investigacion, Desarrollo e Innovacion.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Contribución de congreso (ConferenceOutput)

Parallelization of an algorithm for automatic classification of medical data

  • García Mollá, Víctor Manuel|||0000-0003-4768-7367
  • Salazar Afanador, Addisson|||0000-0001-5849-5104
  • Vidal Maciá, Antonio Manuel
  • Vergara Domínguez, Luís|||0000-0001-6803-4774
  • Safont Armero, Gonzalo
In this paper, we present the optimization and parallelization of a state-of-the-art algorithm for automatic classification, in order to perform real-time classification of clinical data. The parallelization has been carried out so that the algorithm can be used in real time in standard computers, or in high performance computing servers. The fastest versions have been obtained carrying out most of the computations in Graphics Processing Units (GPUs). The algorithms obtained have been tested in a case of automatic classification of electroencephalographic signals from patients., This work was supported by Spanish Administration (Ministerio de Economía y Competitividad) and European Union (FEDER) under grants TEC2014-58438-R and TEC2017-84743-P; and Generalitat Valenciana under grants PROMETEO II/2014/032 and PROMETEO II/2014/003.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Reconfigurable lattice mesh designs for programmable photonic processors

  • Pérez-López, Daniel
  • Soref, Richard A.
  • Gasulla Mestre, Ivana|||0000-0001-8088-7796
  • Capmany Francoy, José|||0000-0002-6460-4167
[EN] We propose and analyse two novel mesh design geometries for the implementation of tunable optical cores in programmable photonic processors. These geometries are the hexagonal and the triangular lattice. They are compared here to a previously proposed square mesh topology in terms of a series of figures of merit that account for metrics that are relevant to on-chip integration of the mesh. We find that that the hexagonal mesh is the most suitable option of the three considered for the implementation of the reconfigurable optical core in the programmable processor., The authors wish to acknowledge the financial support given by the Research Excellency Award Program GVA PROMETEO II/2013/012, Spanish MINECO projects TEC2013-42332-P PIF4ESP, TEC2015-69787-REDT PIC4TB and TEC2014-60378-C2-1-R MEMES, as well as the projects FEDER UPVOV 10-3E-492 and FEDER UPVOV 08-3E-008. The work of D. Perez was supported by the FPI-UPV Grant Program from the Universitat Politecnica de Valencia and the work of I. Gasulla was supported by the Spanish MINECO through the Ramon y Cajal Program. R. Soref is supported by the Air Force Office of Scientific Research.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Contribución de congreso (ConferenceOutput)

Performance evaluation of MIMO channel estimation for ATSC 3.0

  • Shitomi, Takuya
  • Garro, Eduardo
  • Murayama, Kenichi
  • Gomez-Barquero, David|||0000-0003-2610-7765
[EN] ATSC 3.0, the latest Digital Terrestrial Television (DTT) standard, allows a higher spectral efficiency and/or a transmission robustness with Multiple-Input Multiple-Output (MIMO) technology compared to existing single-antenna DTT networks. Regarding MIMO channel estimation, two pilot encoding algorithms known as Walsh-Hadamard encoding and Null pilot encoding are possible in ATSC 3.0. The two MIMO pilot algorithms are standardized so as to have the same pilot positions and the same pilot boosting as SISO, but the performance has not been evaluated. This paper focuses on the performance evaluation of the two MIMO pilot encoding algorithms in ATSC 3.0 using physical layer simulations. Results can be used as guidelines or recommended practices to broadcasters to select the MIMO pilot encoding algorithm that better suits their service requirments. Several channel estimation algorithms have been evaluated in both mobile and fixed reception conditions. The simulation results show that Null pilot encoding provides slightly better performance than WalshHadamard encoding for fixed reception but worse performance for mobile reception, especially at high signal-to-noise ratios., This work was partially supported by the Ministerio de Educacion y Ciencia, Spain (TEC2014-56483-R), co-funded by European FEDER funds.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Simple closed-form property expressions of a metafluid composed of a hexagonal array of transversely isotropic elastic fibres embedded in an ideal fluid

  • Sabina, Federico J.
  • Guinovart-Díaz, Raúl
  • Rodríguez-Ramos, Reinaldo
  • Bravo-Castillejo, Julián
  • Sánchez-Dehesa Moreno-Cid, José|||0000-0003-0742-4407
[EN] A hexagonal array of parallel circular cylinders embedded in a matrix is considered. The fibers are filled with a transversely isotropic (TI) elastic material whereas the matrix material is an ideal fluid. The asymptotic homogenization method, applied to a similar problem where the matrix is also a TI elastic material, produces formulae for the effective TI elastic composite. By a limit procedure when the shear modulii of matrix tend to zero, the formulae yield very simple expressions for the effective composite for the above problem, namely, it is a TI metafluid. The particular case of isotropic fibres leads to an isotropic metafluid. (C) 2019 Elsevier Ltd. All rights reserved., This work was sponsored by PAPIIT-DGAPA-UNAM IA100919. One of the authors (95) thanks to Universitat Politecnica de Valencia, Spain for providing facilities to carry out this work and DGAPA, UNAM for funding the visit. Another author (RR) is grateful for the financial support of Departamento de Maternaticas y Mecanica, IIMAS and PREI-DGAPA, UNAM. (JS-D) acknowledges the support by the Spanish Ministerio de Economia y Competitividad, and the European Union Fondo Europeo de Desarrollo Regional (FEDER) through Project No. TEC2014-53088-C3-1-R.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Computer modelling of RF ablation in cortical osteoid osteoma: Assessment of the insulating effect of the reactive zone

  • Irastorza, Ramiro M.
  • Martel Villagran, Jose
  • Trujillo Guillen, Macarena|||0000-0003-4145-2188
  • Berjano, Enrique|||0000-0002-3247-2665
Purpose: The aim was to study by computer simulations the insulating role of the reactive zone surrounding a cortical osteoid osteoma (OO) in terms of electrical and thermal performance during radiofrequency ablation (RFA). Material and methods: We modelled a cortical OO consisting of a nidus (10 mm diameter) enclosed by a reactive zone. The OO was near a layer of cortical bone 1.5 mm thick. Trabecular bone partially surrounds the OO and there was muscle around the cortical bone layer. We modelled RF ablations with a noncooled-tip 17-gauge needle electrode (300 s duration and 90 C target temperature). Sensitivity analyses were conducted assuming a reactive zone electrical conductivity value (rz) within the limits of the cortical and trabecular bone, i.e. 0.02 S/m and 0.087 S/m, respectively. In this way we were really modelling the different degrees of osteosclerosis associated with the reactive zone. Results: The presence of the reactive zone drastically reduced the maximum temperature reached outside it. The temperature drop was proportional to the thickness of the reactive zone: from 68 C when it was absent to 44 C when it is 7.5 mm thick. Higher nidus conductivity values (n) implied higher temperatures, while lower temperatures meant higher rz values. Changing rz from 0.02 S/m to 0.087 S/m reduced lesion diameters from 2.4 cm to 1.8 cm. Conclusions: The computer results suggest that the reactive zone plays the role of insulator in terms of reducing the temperature in the surrounding area. Keywor, This work was supported by a grant from the Agencia Nacional de Promocion Cientifica y Tecnologica de Argentina (Ref. PICT-2012-1201), and by the Spanish Programa Estatal de Investigacion, Desarrollo e Innovacion Orientada a los Retos de la Sociedad under grant number TEC2014-52383-C3-R (TEC2014-52383-C3-1-R). The authors alone are responsible for the content and writing of the paper.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

SCM Adaptation to Improve Scanning Rate in RF Interferometry Applications

  • Benítez-González, Jesús
  • Bolea Boluda, Mario
  • Mora Almerich, José|||0000-0002-2877-4118
[FR] In this letter, we present a novel structure for performing subcarrier multiplexing (SCM) to improve the scanning rate in low coherence interferometry (LCI) systems combined with the microwave photonics (MWP) technology. In this MWP-LCI proposal, the optical path differences (OPDs) produced by different samples between the arms of an interferometer are closely related to the central frequency of different RF resonances generated in the RF domain. By the proposed adaptation of the SCM technique, M subcarriers are multiplexed in the modulation stage and each subcarrier is set to sweep simultaneously a concrete part of the spectrum. The complete electrical transfer function of the structure is obtained combining each individual sweep. Therefore, a considerable reduction of the sweep time is provided to collect the complete electrical transfer function. Therefore, the scanning rate is reduced according to the number of subcarriers (M) employed in the multiplexing stage. An OPD range of 8 mm is achieved with a constant resolution of 120 &#956;m in the whole range. Finally, a maximum sensitivity of 60 dB is also reached for that operation range., The research leading to these results was supported by the National Project TEC2014-60378-C2-1-R funded by the Ministerio de Ciencia y Tecnologia and the regional project PROMETEO FASE II/2013/012 funded by the Generalitat Valenciana. (Corresponding author: J. Mora.)
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Dielectric characterization of healthy and malignant colon tissues in the 0.5 18 GHz frequency band

  • Fornés Leal, Alejandro|||0000-0001-5914-6045
  • Garcia-Pardo, Concepcion|||0000-0002-2774-980X
  • Cardona Marcet, Narciso|||0000-0001-5697-1453
  • Frasson, M.
  • Pons Beltrán, Vicente
Several reports over the last few decades have shown that the dielectric properties of healthy and malignant tissues of the same body organ usually show different values. However, no intensive dielectric studies of human colon tissue have been performed, despite colon cancer's being one of the most common types of cancer in the world. In order to provide information regarding this matter, a dielectric characterization of healthy and malignant colon tissues is presented. Measurements are performed on ex vivo surgery samples obtained from 20 patients, using an open-ended coaxial probe in the 0.5 18 GHz frequency band. Results show that the dielectric constant of colon cancerous tissue is 8.8% higher than that of healthy tissues (p = 0.002). Besides, conductivity is about 10.6% higher, but in this case measurements do not have statistical significance (p = 0.038). Performing an analysis per patient, the differences in dielectric constant between healthy and malignant tissues appear systematically. Particularized results for specific frequencies (500 MHz, 900 MHz, 2.45 GHz, 5 GHz, 8.5 GHz and 15 GHz) are also reported. The findings have potential application in early-stage cancer detection and diagnosis, and can be useful in developing new tools for hyperthermia treatments as well as creating electromagnetic models of healthy and cancerous tissues., The authors would like to thank the medical staff of the endoscopy unit of Hospital Universitari i Politecnic La Fe for their assistance in the gathering of tissue samples. This work was supported by Ministerio de Economia y Competitividad, Spain (ref. TEC2014-60258-C2-1-R, TEC2014-56469-REDT), by FEDER funds, and by a UPV-IISLaFe action (CEI-2G, 2014).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Flying ad-hoc network application scenarios and mobility models

  • Bujari, Armir
  • Palazzi, Claudio Enrico
  • Ronzani, Daniele
  • Tavares De Araujo Cesariny Calafate, Carlos Miguel|||0000-0001-5729-3041
  • Cano, Juan-Carlos|||0000-0002-0038-0539
  • Manzoni, Pietro|||0000-0003-3753-0403
[EN] Flying ad-hoc networks are becoming a promising solution for different application scenarios involving unmanned aerial vehicles, like urban surveillance or search and rescue missions. However, such networks present various and very specific communication issues. As a consequence, there are several research studies focused on analyzing their performance via simulation. Correctly modeling mobility is crucial in this context and although many mobility models are already available to reproduce the behavior of mobile nodes in an ad-hoc network, most of these models cannot be used to reliably simulate the motion of unmanned aerial vehicles. In this article, we list the existing mobility models and provide guidance to understand whether they could be actually adopted depending on the specific flying ad-hoc network application scenarios, while discussing their advantages and disadvantages.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

An Intelligent Transportation System Application for Smartphones Based on Vehicle Position Advertising and Route Sharing in Vehicular Ad-Hoc Networks

  • Hadiwardoyo, Seilendria Ardityarama
  • Patra, Subhadeep
  • Tavares De Araujo Cesariny Calafate, Carlos Miguel|||0000-0001-5729-3041
  • Cano, Juan-Carlos|||0000-0002-0038-0539
  • Manzoni, Pietro|||0000-0003-3753-0403
[EN] Alerting drivers about incoming emergency vehicles and their routes can greatly improve their travel times in congested cities, while reducing the risk of accidents due to distractions. This paper contributes to this goal by proposing Messiah, an Android application capable of informing regular vehicles about incoming emergency vehicles like ambulances, police cars and fire brigades. This is made possible by creating a network of vehicles capable of directly communicating between them. The user can, therefore, take driving decisions in a timely manner by considering incoming alerts. Using the support of our GRCBox hardware, the application can rely on vehicular ad-hoc network communications in the 5 GHz band, being V2V (vehicle-to-vehicle) communication provided through a combination of Android-based smartphone and our GRCBox device. The application was tested in three different scenarios with different levels of obstruction, showing that it is capable of providing alerts up to 300 meters, and notifying vehicles within less than one second, This work was partially supported by the "Ministerio de Economia y Competividad, Programa Estatal de Investigacion, Desarollo e Innovacion Orientada a los Retos de la Sociedad, Proyectos I+D+I 2014", Spain, under Grant Nos. TEC2014-52690-R and BES-2015-075988.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Foundry Developments Toward Silicon Nitride Photonics From Visible to the Mid-Infrared

  • P. Muñoz|||0000-0001-6026-1649
  • Mico-Cabanes, Gloria|||0000-0003-1812-5883
  • Pastor Abellán, Daniel|||0000-0002-5297-3918
  • van Dijk, Paulus W. L.
  • Geuzebroek, Douwe
  • Geiselmann, Michael
  • Domínguez, Carlos
  • Stassen, Andim
  • Doménech, José David
  • Zervas, Michael
  • Leinse, Arne
  • Roeloffzen, Chris G.H.
  • Gargallo, Bernardo
  • Baños, Rocio
  • Fernández, Juan
  • Bru-Orgiles, Luis Alberto
[EN] Photonic integration technologies have spread in the past decade by means of foundry models that mirror the electronic-integrated circuit industry developments of the past century. Several monolithic technologies exist, based on silicon and III-V semiconductors. In this paper, we discuss the current state and forthcoming developments of open access photonic foundries whose technology platforms are based on silicon nitride material. The paper presents various silicon nitride technologies and foundries, alongside with access models supported by generic integration and process design kits. Technical features, enabled by different micro-fabrication processes and tools are summarized. Application examples and developments of forthcoming incorporation into these platforms are outlined., This work was supported in part by the Spanish MINECO projects TEC2016-80385-P SINXPECT, in part by TEC2014-54449-C3-1-R, in part by the EC H2020-ICT-27-2015 PICs4all CSA 687777, in part by the DARPA DODOS program, in part by H2020-ICT-2017-1 MOICANA RIA 780537, and in part by PIX4life IP 688519. The work of R. Banos was supported by PTQ-15-07966. The work of J. Fernandez was supported by DI-15-08031. The work of G. M. Cabanes was supported by BES-2014-068523. The work of L. A. Bru was supported by PTA2015-11309-I.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Reconfigurable Radio Access Networks Using Multicore Fibers

  • Galve-Higón, José Manuel
  • Gasulla Mestre, Ivana|||0000-0001-8088-7796
  • Sales Maicas, Salvador|||0000-0001-9457-976X
  • Capmany Francoy, José|||0000-0002-6460-4167
We propose the use of spatial division multiplexing supported by multicore fibers to implement a new generation of flexible and capacity reconfigurable cloud radio access network front-haul architectures capable of addressing their main present and future challenges. We show that for the majority of radio access scenarios where front-haul optical links are less than 10-km long, the impact of inter-core crosstalk on the electrical carrier-to-noise ratio can be neglected, and thus, link design can be carried independently core by core. In addition, this MCF-based approach, which is compatible with software defined networking and network function virtualization, can also support the integration of a passive optical network overlay., This work was supported in part by the Ministry of Economy and Competitiveness under Project TEC2013-50552-EXP MULTIFUN and Project TEC2014-60378-C2-1-R MEMES and in part by Generalitat Valenciana under Grant PROMETEO 2013/012. The work of I. Gasulla was supported by the Spanish Ministry of Economy and Commerce through the Ramon y Cajal Program.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Enhancement of the sensitivity of a temperature sensor based on fiber Bragg gratings via weak value amplification

  • Salazar-Serrano, L.J.
  • Amaya Ocampo, Waldimar Alexander
  • Pruneri, V..
  • Torres, J.P.
  • Barrera Vilar, David|||0000-0002-1700-6842
  • Sales Maicas, Salvador|||0000-0001-9457-976X
  • Capmany Francoy, José|||0000-0002-6460-4167
We present a proof-of-concept experiment aimed at increasing the sensitivity of Fiber-Bragg-gratings temperature sensors by making use of a weak-value-amplification scheme. The technique requires only linear optics elements for its implementation and appears as a promising method for increasing the sensitivity than state-of the-art sensors can currently provide. The device implemented here is able to generate a shift of the centroid of the spectrum of a pulse of &#8764;0.035 nm&#8725;°C, a nearly fourfold increase in sensitivity over the same fiber-Bragg-grating system interrogated using standard methods., Severo Ochoa program; Fundacio Privada Cellex, Barcelona; Research Excellency Award Program GVA PROMETEO 2013/012; Spanish MCINN (TEC2014-53727-C2-1-R).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Spot events detection along a large scale sensor based on ultra weak FBGs using time-frequency analysis

  • Ricchiuti, Amelia Lavinia
  • Sales Maicas, Salvador|||0000-0001-9457-976X
[EN] A simple scheme for interrogating a 5 m-long photonics device and its potential applications to quasi-distributed fiber sensing is proposed. The sensor consists of an array of 500 identical very weak fiber Bragg gratings (FBGs). The gratings are 9 mm-long and have been serially written in cascade along a single optical fiber. The measurement system is based on a combination of optical time domain reflectrometry (OTDR) and frequency scanning of the interrogating pulse. The time-frequency analysis is performed by launching an optical pulse into the sensor and by retrieving and analyzing the back-reflected signal. The measurement of the temperature, length and position of spot events along the sensors is demonstrated, with good accuracy. As both spatial and temperature resolution of the method depend on the input pulse duration, the system performance can be controlled and optimized by properly choosing the temporal duration of the interrogating pulse. A spatial resolution of 9 mm (ultimately dictated by one grating length) has been obtained with an 80 ps optical pulse; while a temperature resolution of less than 0.42 K has been demonstrated using a 500 ps incident pulse. The sensor proposed proves to be simple, robust, polarization insensitive and alleviates the instrumentation complexity for distributed sensing applications., Ministerio de Educacion, Cultura y Deporte; Ministerio de Economia y Competitividad (TEC2014-60378-C2-1-R); Generalitat Valenciana (GRISOLIA/2013/034); Research Excellency Award Program (GVA PROMETEO 2013/012).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Effect of the trabecular bone microstructure on measuring its thermal conductivity: A computer modeling-based study

  • Fajardo, Jesús E.
  • Carlevaro, C. Manuel
  • Vericat, Fernando
  • Irastorza, Ramiro Miguel
  • Berjano, Enrique|||0000-0002-3247-2665
[EN] The objective of this work is to quantify the relation between the value of the effective thermal conductivity of trabecular bone and its microstructure and marrow content. The thermal conductivity of twenty bovine trabecular bone samples was measured prior to and after defatting at 37, 47, and 57 degrees C. Computer models were built including the microstructure geometry and the gap between the tissue and measurement probe. The thermal conductivity (k) measured was 0.39 +/- 0.06 W m(-1) K-1 at 37 degrees C, with a temperature dependence of + 0.2%degrees C-1. Replacing marrow by phosphate-buffered saline (defatting) increased both the computer simulations and measurement results by 0.04 W m(-1) K-1. The computer simulations showed that k increases by 0.02-0.04 W m(-1) K-1 when the model includes a gap filled by phosphate-buffered saline between the tissue and measurement probe. In the presence of microstructure and fatty red marrow, k varies by +/- 0.01 W m(-1) K-1 compared with the case considering matrix only, which suggests that there are no significant differences between cortical and trabecular bone in terms of k. The computer results showed that the presence of a gap filled by phosphate-buffered saline around the energy applicator changes maximum temperature by < 0.7 degrees C, while including the bone microstructure involved a variation of < 0.2 mm in the isotherm location. Future experimental studies on measuring the value of k involving the insertion of a probe into the bone through a drill hole should consider the bias found in the simulations. Thermal models based on a homogeneous geometry (i.e. ignoring the microstructure) could provide sufficient accuracy., This work was supported by a grant from the "Agencia Nacional de Promocion Cientfica y Tecnologica de Argentina" (Ref. PICT-2016-2303), by the National Scientific and Technical Research Council of Argentina (Grant PIO CONICET-UNAJ 0001), and by the Spanish "Programa Estatal de Investigacion, Desarrollo e Innovacion Orientada a los Retos de la Sociedad" under Grant TEC2014-52383-C3-R (TEC2014-52383-C3-1-R).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Microwave Photonic Filtering for Interrogating FBG-Based Multicore Fiber Curvature Sensor

  • Zheng, Di
  • Madrigal-Madrigal, Javier|||0000-0003-3156-1321
  • Barrera Vilar, David|||0000-0002-1700-6842
  • Sales Maicas, Salvador|||0000-0001-9457-976X
  • Capmany Francoy, José|||0000-0002-6460-4167
[EN] We propose and experimentally demonstrate an approach to perform high-resolution and temperature-insensitive interrogation of a fiber Bragg grating (FBG)-based multicore fiber (MCF) curvature sensor using a microwave photonics filtering technique. By combining two reflected sample signals from the two FBGs inscribed in MCF and a dispersion device, a two-tap notch microwave photonic filter (MPF) is formed. The notch frequency of MPF is dependent on the time delay difference between the two FBG reflected signals, which is related to wavelength spacing of the two FBGs. Due to the wavelength spacing of the two FBGs is proportional to the curvature, the curvature can be readily interrogated by monitoring the notch frequency of MPF. The proposed interrogation scheme with the sensitivity of 92 MHz/m(-1) is achieved, whilst the sensitivity can be easily adjusted. Moreover, the proposed interrogation scheme is temperature insensitive., This work was supported in part by the National Natural Science Foundation of China under Grant 61405166 and Grant 61775185, in part by the China Scholarship Council, in part by the Generalitat Valenciana under Grant APOSTD/2016/015 and Grant GVA PROMETEO 2013/012, and in part by the Ministerio de Economia y Competitividad under Grant TEC2014-60378-C2-1-R. (Corresponding author: Di Zheng.)
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

A Discretized Approach to Air Pollution Monitoring Using UAV-based Sensing

  • Alvear-Alvear, Óscar
  • Zema, Nicola
  • Natalizio, Enrico
  • Tavares De Araujo Cesariny Calafate, Carlos Miguel|||0000-0001-5729-3041
  • Hernández-Orallo, Enrique|||0000-0002-3284-561X
  • Cano, Juan-Carlos|||0000-0002-0038-0539
  • Manzoni, Pietro|||0000-0003-3753-0403
[EN] Recently, Unmanned Aerial Vehicles (UAVs) have become a cheap alternative to sense pollution values in a certain area due to their flexibility and ability to carry small sensing units. In a previous work, we proposed a solution, called Pollution-driven UAV Control (PdUC), to allow UAVs to autonomously trace pollutant sources, and monitor air quality in the surrounding area. However, despite operational, we found that the proposed solution consumed excessive time, especially when considering the battery lifetime of current multi-rotor UAVs. In this paper, we have improved our previously proposed solution by adopting a space discretization technique. Discretization is one of the most efficient mathematical approaches to optimize a system by transforming a continuous domain into its discrete counterpart. The improvement proposed in this paper, called PdUC-Discretized (PdUC-D), consists of an optimization whereby UAVs only move between the central tile positions of a discretized space, avoiding monitoring locations separated by small distances, and whose actual differences in terms of air quality are barely noticeable. We also analyze the impact of varying the tile size on the overall process, showing that smaller tile sizes offer high accuracy at the cost of an increased flight time. Taking into account the obtained results, we consider that a tile size of 100 x 100 meters offers an adequate trade-off between flight time and monitoring accuracy. Experimental results show that PdUC-D drastically reduces the convergence time compared to the original PdUC proposal without loss of accuracy, and it also increases the performance gap with standard mobility patterns such as Spiral and Billiard., This work was partially supported by the "Programa Estatal de Investigacion, Desarrollo e Innovacion Orientada a Retos de la Sociedad, Proyecto I+D+I TEC2014-52690-R", the framework of the DIVINA Challenge Team, which is funded under the Labex MS2T program. Labex MS2T is supported by the French Government, through the program "Investments for the future" managed by the National Agency for Research (Reference: ANR-11-IDEX-0004-02), the "Programa de becas SENESCYT de la Republica del Ecuador", and the Research Direction of the University of Cuenca.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Capítulo o parte de un libro (BookPart)

Improving Message Delivery Performance in Opportunistic Networks using a Forced-stop diffusion scheme

  • HERRERA TAPIA, JORGE
  • Hernández-Orallo, Enrique|||0000-0002-3284-561X
  • Tomás Domínguez, Andrés Enrique
  • Manzoni, Pietro|||0000-0003-3753-0403
  • Tavares De Araujo Cesariny Calafate, Carlos Miguel|||0000-0001-5729-3041
  • Cano, Juan-Carlos|||0000-0002-0038-0539
The performance of mobile opportunistic networks strongly depends on contact duration. If the contact lasts less than the required transmission times, some messages will not get delivered, and the whole diffusion scheme will be seriously affected. In this paper we propose a new diffusion method, called Forced-Stop, that is based on controlling node mobility to guarantee a complete message transfer. Using the ONE simulator and realistic mobility traces, we compared our proposal with the classical Epidemic diffusion. We show that Forced-Stop improves the message delivery performance, increasing the delivery ratio up to 30\%, and reducing the latency of message delivery up to 40\%, with a limited impact on buffer utilisation and message relaying. These results can be a relevant indication to the designers of opportunistic network applications that could integrate in their products strategies to inform the user about the need to temporarily stop in order to favor the overall data delivery., This work was partially supported by the Ministerio de Economía y Competitividad, Programa Estatal de Investigación, Desarrollo e Innovación Orientada a los Retos de la Sociedad, Proyectos I+D+I 2014, Spain, under Grant TEC2014-52690-R, the Generalitat Valenciana, Spain, under Grant AICO/2015/108, the Secretaría Nacional de Educación Superior, Ciencia, Tecnología e Innovación del Ecuador(SENESCYT), and the Universidad Laica Eloy Alfaro de Manabi, Ecuador.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Numerical analysis of thermal impact of intramyocardial capillary blood flow during radiofrequency cardiac ablation

  • Pérez, Juan J|||0000-0001-8486-8699
  • González-Suárez, Ana|||0000-0002-1813-4176
  • Berjano, Enrique|||0000-0002-3247-2665
[EN] Purpose: The thermal effect of the intramyocardial blood perfusion on the size of lesions created by radiofrequency cardiac ablation (RFCA) has not been adequately studied to date. Our objective was to assess the impact of including this phenomenon in RFCA computer modelling in terms of the thermal lesion depth created.Methods: A computer model was built and computer simulations were conducted to assess the effect of including the blood perfusion term in the bioheat equation. This term mimics the intramyocardial blood flow (i.e., blood perfusion) in the cardiac wall at the site at which the RFCA is being conducted and hence represents a heat removing mechanism. When considered, blood perfusion rates ranged from 609 to 1719ml/min/kg. Two electrode design and modes were considered: a non-irrigated electrode with constant temperature mode and an irrigated electrode with constant power mode.Results: All the depths computed without including the blood perfusion term were larger than those that did include it, regardless of perfusion rate. The differences in lesion depth between ignoring and including blood perfusion increased over time; for a 60s RFCA they were 0.45 and 1mm for minimum and maximum perfusion rate, respectively. The differences were more or less independent of blood flow in the cardiac chamber, electrode type and ablation mode.Conclusions: The findings suggest that the heat-sink effect of blood perfusion should be taken into account in the case of ablations (>1minute) such as those conducted in RFCA of the ventricular wall., This work was supported by the Ministerio de Economia y Competitividad under "Plan Estatal de Investigacion, Desarrollo e Innovacion Orientada a los Retos de la Sociedad" Grant "TEC2014- 52383-C3 [TEC2014-52383-C3-1-R]". A. Gonzalez-Suarez had a Postdoctoral Grant [APOSTD/2016/045] from the Generalitat Valenciana (Spain) and currently has a Postdoctoral Grant "Juan de la Cierva-formacion" [FJCI-2015-27202] supported by the Spanish Ministerio de Economia, Industria y Competitividad.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Few-mode fiber true time delay lines for distributed radiofrequency signal processing

  • Guillem-Cogollos, Rubén
  • García-Cortijo, Sergi|||0000-0002-7237-9457
  • Madrigal-Madrigal, Javier|||0000-0003-3156-1321
  • Barrera Vilar, David|||0000-0002-1700-6842
  • Gasulla Mestre, Ivana|||0000-0001-8088-7796
[EN] We report, for the first time to our knowledge. distributed radiofrequency signal processing built upon true time delay operation on a step-index few-mode fiber. Two 3-sample configurations with different time delay properties are implemented over the same 60-meter 4-LP-mode fiber link. The inscription of a long period grating at a specific fiber position converts part of the LP01 mode into the LP02, permitting sample time delay engineering. Delay line performance is experimentally demonstrated when applied to radiofrequency signal filtering. example of fiber-distributed processing functionality exhibiting one order or magnitude gain in terms of compactness. (C) 2018 Optical Society of America America under the terms of the OSA Open Access Publishing Agreement, H2020 European Research Council (ERC) (Consolidator Grant 724663); Spanish MINECO (TEC2014-60378-C2-1-R and TEC2016-80150-R projects, BES-2015-073359 scholarship for S. Garcia, Ramon y Cajal fellowship RYC-2014-16247 for I. Gasulla)., © 2018 Optical Society of America. One print or electronic copy may be made for personal use only. Systematic reproduction and distribution, duplication of any material in this paper for a fee or for commercial purposes, or modifications of the content of this paper are prohibited
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Frequency Dependence of UWB In-Body Radio Channel Characteristics

  • Andreu-Estellés, Carlos
  • Garcia-Pardo, Concepcion|||0000-0002-2774-980X
  • Castelló-Palacios, Sergio|||0000-0003-4689-652X
  • Vallés Lluch, Ana|||0000-0002-7896-8666
  • Cardona Marcet, Narciso|||0000-0001-5697-1453
[EN] In this letter, a research of ultra-wideband in-body channel by using a high accurate phantom is performed in order to evaluate the impact of frequency dependence of human tissues on the channel characteristics. Hence, a phantom-based measurement campaign from 3.1 to 5.1 GHz has been conducted. From postprocessing data, the path loss is assessed considering subbands of 500 MHz as well as the entire frequency range under test. In addition, the correlation in transmission is computed and discussed., This work was supported in part by the Ministerio de Economia y Competitividad, Spain, under Grant TEC2014-60258-C2-1-R, and in part by the European FEDER funds. (Corresponding author: Carlos Andreu.)
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Poisson-like effect for flexural waves in periodically perforated thin plates

  • Gao, Penglin
  • Wu, Linzhi
  • Sánchez-Dehesa Moreno-Cid, José|||0000-0003-0742-4407
[EN] The Poisson-like effect, describing the redirection of waves by 90 degrees, is shown to be feasible for flexural waves propagating in perforated thin plates. It is demonstrated that the lowest order symmetric leaky guided mode (S0 mode) is responsible for the splitting of wave motion in two orthogonal directions. The S0 mode shows a feature of stationary waves containing standing wave modes in one and two orthogonal directions for smaller and larger holes, respectively. The former case is well understood thanks to the phenomenon of Wood's anomaly, which was first observed in optical gratings supposed to be transparent. On the contrary, the strong scattering caused by the larger holes leads to a mixed mode occurring when the incident wave is totally transmitted. The mixed mode easily couples with the incoming waves and, therefore, the Poisson-like effect activated under this mechanism is much stronger. Using the Poisson-like effect, a device is proposed in which about 82% of the incident mechanical energy is redirected to the perpendicular direction. Results obtained with arrays of free holes also apply to inclusions with parameters properly chosen. The findings may provide applications in beam splitting and waveguiding. (C) 2018 Acoustical Society of America., Work supported by the Ministerio de Economia y Competitividad of Spain and the EU Fondo Europeo de Desarrollo Regional under Project No. TEC2014-53088-C3-1-R, and the National Natural Science Foundation of China under Grants Nos. 11432004 and 11421091. P.G. acknowledges a scholarship with No. 201606120070 provided by China Scholarship Council.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Viscothermal Losses in Double-Negative Acoustic Metamaterials

  • Cutanda-Henriquez, V.
  • García Chocano, Víctor Manuel
  • Sánchez-Dehesa Moreno-Cid, José|||0000-0003-0742-4407
[EN] The influence of losses in double-negative metamaterial slabs recently introduced by Graciá-Salgado et al. [Phys. Rev. B 88, 224305 (2013)] is comprehensively studied. Viscous and thermal losses are considered in the linearized Navier-Stokes equations with no flow. Despite the extremely low thicknesses of boundary layers associated with each type of losses, the double-negative behavior is totally suppressed for the rigid structures under analysis. In other words, almost 100% of the energy transmitted into the slab is dissipated by viscothermal effects, in agreement with experimental data. Simulations undertaken for larger structures, using scale factors of up to 20 times, show that double-negative behavior is never recovered. The huge dissipation obtained by these structures leads us to propose them as interesting alternatives to conventional absorbers for specific situations, e.g., when treating low frequencies or when the excitation is narrow banded., V. M. G.-C. and J. S.-D. acknowledge the support from the Spanish Ministerio de Economia y Competitividad (MINECO), and the European Union Fondo Europeo de Desarrollo Regional (FEDER) through Project No. TEC 2014-53088-C3-1-R.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Computational modeling of internally cooled wet (ICW) electrodes for radiofrequency ablation: Impact of rehydration, thermal convection and electrical conductivity

  • Trujillo Guillen, Macarena|||0000-0003-4145-2188
  • Bon Corbín, José|||0000-0002-0457-9705
  • Berjano, Enrique|||0000-0002-3247-2665
[EN] Purpose: (1) To analyse rehydration, thermal convection and increased electrical conductivity as the three phenomena which distinguish the performance of internally cooled electrodes (IC) and internally cooled wet (ICW) electrodes during radiofrequency ablation (RFA), (2) Implement a RFA computer model with an ICW which includes these phenomena and (3) Assess their relative influence on the thermal and electrical tissue response and on the coagulation zone size. Methods: A 12-min RFA in liver was modelled using an ICW electrode (17G, 3cm tip) by an impedance-control pulsing protocol with a constant current of 1.5A. A model of an IC electrode was used to compare the ICW electrode performance and the computational results with the experimental results. Results: Rehydration and increased electrical conductivity were responsible for an increase in coagulation zone size and a delay (or absence) in the occurrence of abrupt increases in electrical impedance (roll-off). While the increased electrical conductivity had a remarkable effect on enlarging the coagulation zone (an increase of 0.74cm for differences in electrical conductivity of 0.31S/m), rehydration considerably affected the delay in roll-off, which, in fact, was absent with a sufficiently high rehydration level. In contrast, thermal convection had an insignificant effect for the flow rates considered (0.05 and 1mL/min). Conclusions: Computer results suggest that rehydration and increased electrical conductivity were mainly responsible for the absence of roll-off and increased size of the coagulation zone, respectively, and in combination allow the thermal and electrical performance of ICW electrodes to be modelled during RFA., This work was supported by the Government of Spain through the Spanish Plan Estatal de Investigacion, Desarrollo e Innovacion Orientada a los Retos de la Sociedad under grant number TEC2014-52383-C3-R (TEC2014-52383-C3-1-R).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Integration of vehicular network and smartphones to provide real-time visual assistance during overtaking

  • Patra, Subhadeep
  • Veelaert, Peter
  • Philips, Wilfried
  • Tavares De Araujo Cesariny Calafate, Carlos Miguel|||0000-0001-5729-3041
  • Cano, Juan-Carlos|||0000-0002-0038-0539
[EN] The Intelligent Transportation Systems area has experienced great developments in the recent past, although suffering from slow adoption ratios thus depriving consumers of many interesting and innovative applications. The only solution to this problem is to develop Intelligent Transportation Systems solutions using the already available technologies that are within the grasp of the common people, to make them cost-effective, quick to deploy and easy to adopt. We have therefore developed an affordable Intelligent Transportation Systems that make use of standard smartphones to assist drivers when overtaking. The system autonomously creates a network among the close-by vehicles and provides drivers with a real-time video feed from the one located just ahead. Our system seamlessly offers a better view of the road, and of any vehicle travelling in the opposite direction, being especially useful when the front view of the driver is blocked by large vehicles. We have validated our overtaking assistance system, in both laboratory environment and realistic scenarios. The laboratory tests involved choosing the most effective video codec between MJPEG and H.264, for providing real-time video streaming. Then, using the chosen codec, we performed the outdoor tests to further tune our application to maximise performance. The preliminary results from our experiments allow being optimistic about the effectiveness and applicability of the proposed system., The author(s) disclosed receipt of the following financial support for the research, authorship, and/or publication of this article: This work was partially supported by the Special Research Fund – funding for joint doctorates of the Ghent University with scholarship code 01SF3316, and the Ministerio de Economía y Competitividad, Programa Estatal de Investigación, Desarrollo e Innovación Orientada a los Retos de la Sociedad, Proyectos I+D+I 2014, Spain, under grant TEC2014-52690-R.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Effect of applied voltage, duration and repetition frequency of RF pulses for pain relief on temperature spikes and electrical field: A computer modeling study

  • Ewertowska, Elzbieta
  • Mercadal, Borja
  • Muñoz, Víctor
  • Ivorra, Antoni
  • Trujillo Guillen, Macarena|||0000-0003-4145-2188
  • Berjano, Enrique|||0000-0002-3247-2665
[EN] Background: The thermal and electrical effects of pulsed radiofrequency (PRF) for pain relief can be controlled by modifying the characteristics of the RF pulses applied. Our goal was to evaluate the influence of such modifications on the thermal and electric performance in tissue. Methods: A computational model was developed to compare the temperature and electric field time courses in tissue between a standard clinical protocol (45 V pulses, 20ms duration, 2 Hz repetition frequency) and a new protocol (55 V pulses, 5ms duration, 5 Hz repetition frequency) with a higher applied electric field but a smaller impact on temperature alterations in tissue. The effect of including a temperature controller was assessed. Complementarily, an agar-based experimental model was developed to validate the methodology employed in the computer modelling. Results: The new protocol increased the electric field magnitude reached in the tissue by around +20%, without increasing the temperature. The temperature controller was found to be the fundamental factor in avoiding thermal damage to the tissue and reduced the total number of pulses delivered by around 67%. The experimental results matched moderately well with those obtained from a computer model built especially to mimic the experimental conditions. Conclusions: For the same delivered energy, the new protocol significantly increases the magnitude of the applied electric field, which may be the reason why it is clinically more effective in achieving pain relief., This work was supported by the Spanish "Plan Estatal de Investigacion, Desarrollo e Innovacion Orientada a los Retos de la Sociedad" under Grant TEC2014-52383-C3-R (TEC2014-52383-C3-1-R and TEC2014-52383-C3-2-R). Elzbieta Ewertowska has a Predoctoral Grant (BES-2015-073285) from the Ministry of Economy, Industry and Competitiveness (Government of Spain).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Redirection and Splitting of Sound Waves by a Periodic Chain of Thin Perforated Cylindrical Shells

  • Bozhko, Andrey
  • Krokhin, Arkadii
  • Sánchez-Dehesa Moreno-Cid, José|||0000-0003-0742-4407
  • Cervera Moreno, Francisco Salvador
[EN] The scattering of sound by finite and infinite chains of equally spaced perforated metallic cylindrical shells in an ideal (inviscid) and viscous fluid is theoretically studied using rigorous analytical and numerical approaches. Because of perforations, a chain of thin shells is practically transparent for sound within a wide range of frequencies. It is shown that strong scattering and redirection of sound by 90° may occur only for a discrete set of frequencies (Wood¿s anomalies) where the leaky eigenmodes are excited. The spectrum of eigenmodes consists of antisymmetric and symmetric branches with normal and anomalous dispersion, respectively. The antisymmetric eigenmode turns out to be a deaf mode, since it cannot be excited at normal incidence. However, at slightly oblique incidence, both modes can be resonantly excited at different but close frequencies. The symmetric mode, due to its anomalous dispersion, scatters sound in the ¿wrong¿ direction. This property may find an application for the splitting of the two resonant harmonics of the incoming signal into two beams propagating along the chain in the opposite directions. A chain of perforated cylinders may also be used as a passive antenna that detects the direction to the incoming signal by measuring the frequencies of the waves excited in the chain. Calculations are presented for aluminum shells in viscous air where the effects of anomalous scattering, redirection, and signal splitting are well manifested., A. K. acknowledges support from Programa de Apoyo a la Investigacion y Desarrollo (PAID-02-15) de la Universitat Politecnica de Valencia. A. B., F. C., and J. S.-D. acknowledge the support by the Ministerio de Economia y Competitividad of the Spanish government and the European Union Fondo Europeo de Desarrollo Regional (FEDER) through Project No. TEC2014-53088-C3-1-R. The authors are thankful to Michael R. Haberman for fruitful discussion regarding possible applications of the periodic chain of a perforated shell in the processing of acoustic signals.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Experimental Validation of Multipactor Effect for Ferrite Materials Used in L- and S-Band Nonreciprocal Microwave Components

  • Vague Cardona, José Joaquín|||0000-0001-5935-3116
  • Boria Esbert, Vicente Enrique|||0000-0001-7150-9785
  • Reglero Mangada, Marta Sofía|||0000-0002-3811-843X
  • Melgarejo-Lermas, Juan Carlos
  • GUGLIELMI, MARCO
  • Moreno Cambroreno, María del Rocío
  • Mata-Sanz, Rafael
  • Montero, Isabel
  • Gonzalez Iglesias, Daniel
  • GIMENO MARTINEZ, BENITO
  • Gomez, Alvaro
  • Vegas, Ángel
  • RABOSO GARCÍA-BAQUERO, DAVID
[EN] This paper reports on the experimental measurement of power threshold levels for the multipactor effect between samples of ferrite material typically used in the practical implementation of L-and S-band circulators and isolators. For this purposes, a new family of wideband, nonreciprocal rectangular waveguide structures loaded with ferrites has been designed with a full-wave electromagnetic simulation tool. The design also includes the required magnetostatic field biasing circuits. The multipactor breakdown power levels have also been predicted with an accurate electron tracking code using measured values for the secondary electron yield (SEY) coefficient. The measured results agree well with simulations, thereby fully validating the experimental campaign., This work was supported in part by the European Space Agency (ESA) through the Research Project Novel Investigation in Multipactor Effect in Ferrite and Other Dielectrics Used in High Power RF Space Hardware under Contract AO 1-7551/13/NL/GLC, in part by the Ministerio de Economia y Competitividad (Spanish Government) through Research and Development under Project TEC2016-75934-C4-1-R and Project TEC2016-75934-C4-2-R, and in part by the European Regional Development Fund under Project TEC2014-55463-C3-3-P.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Non-Coherent Open-Loop MIMO Communications Over Temporally-Correlated Channels

  • Cabrejas Peñuelas, Jorge
  • Roger Varea, Sandra
  • Fouad, Yaser M. M.
  • Gohary, Ramy H.
  • Yanikomeroglu, Halim
  • Calabuig Soler, Daniel|||0000-0003-0611-9902
  • Monserrat del Río, Jose Francisco|||0000-0001-8664-6408
[EN] This paper investigates the use of non-coherent communication techniques for open-loop transmission over temporally-correlated Rayleigh-fading MIMO channels. These techniques perform data detection without knowing the instantaneous channel coefficients. Three non-coherent Multiple Input Multiple Output (MIMO) schemes, namely, differential unitary space-time modulation, differential space-time block code, and Grassmannian signaling, are compared with several state-of-the-art training-based coherent schemes. This paper shows that the non-coherent schemes are meaningful alternatives to training-based communication, specially as the number of transmit antennas increases. In particular, for more than two transmit antennas, non-coherent communication provides a clear advantage in medium to high mobility scenarios., This work was supported in part by the Ministerio de Economia y Competitividad, Spain, under Grant TEC2014-60258-C2-1-R, in part by the European Regional Development Fund, in part by the European Union through the H2020 Project METIS-II under Grant 671680, in part by Huawei Canada Company, Ltd., and in part by the Ontario Ministry of Economic Development and Innovation's through the Ontario Research Fund-Research Excellence Program.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Modeling Liver Electrical Conductivity during Hypertonic Injection

  • Castellví, Quim
  • Sánchez Velazquez, Patricia
  • Moll, Xavier
  • Andaluz, Anna
  • Burdío, Fernando
  • Bijnens, Bart
  • Ivorra, Antoni
  • Berjano, Enrique|||0000-0002-3247-2665
[EN] Metastases in the liver frequently grow as scattered tumor nodules that neither can be removed by surgical resection nor focally ablated. Previously, we have proposed a novel technique based on irreversible electroporation that may be able to simultaneously treat all nodules in the liver while sparing healthy tissue. The proposed technique requires increasing the electrical conductivity of healthy liver by injecting a hypersaline solution through the portal vein. Aiming to assess the capability of increasing the global conductivity of the liver by means of hypersaline fluids, here, it is presented a mathematical model that estimates the NaCl distribution within the liver and the resulting conductivity change. The model fuses well-established compartmental pharmacokinetic models of the organ with saline injection models used for resuscitation treatments, and it considers changes in sinusoidal blood viscosity because of the hypertonicity of the solution. Here, it is also described a pilot experimental study in pigs in which different volumes of NaCl 20% (from 100 to 200mL) were injected through the portal vein at different flow rates (from 53 to 171 mL/minute). The in vivo conductivity results fit those obtained by the model, both quantitatively and qualitatively, being able to predict the maximum conductivity with a 14.6% average relative error. The maximum conductivity value was 0.44second/m, which corresponds to increasing 4 times the mean basal conductivity (0.11second/m). The results suggest that the presented model is well suited for predicting on liver conductivity changes during hypertonic saline injection., Ministry of Economy and Competitiveness of Spain, Grant/Award Number: TEC2014-52383-C3-1-R, TEC2014-52383-C3-2-R, TEC2014-52383-C3-3-R
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Application of the relative wavelet energy to heart rate independent detection of atrial fibrillation

  • García, Manuel
  • Ródenas García, Juan
  • Alcaraz, Raúl
  • Rieta, J J|||0000-0002-3364-6380
Background and Objectives: Atrial fibrillation (AF) is the most common sustained cardiac ar- rhythmia and a growing healthcare burden worldwide. It is often asymptomatic and may appear as episodes of very short duration; hence, the development of methods for its au- tomatic detection is a challenging requirement to achieve early diagnosis and treatment strategies. The present work introduces a novel method exploiting the relative wavelet energy (RWE) to automatically detect AF episodes of a wide variety in length. Methods: The proposed method analyzes the atrial activity of the surface electrocardio- gram (ECG), i.e., the TQ interval, thus being independent on the ventricular activity. To improve its performance under noisy recordings, signal averaging techniques were applied. The meth- od s performance has been tested with synthesized recordings under different AF variable conditions, such as the heart rate, its variability, the atrial activity amplitude or the pres- ence of noise. Next, the method was tested with real ECG recordings. Results: Results proved that the RWE provided a robust automatic detection of AF under wide ranges of heart rates, atrial activity amplitudes as well as noisy recordings. Moreover, the method s detection delay proved to be shorter than most of previous works. A trade-off between detection delay and noise robustness was reached by averaging 15 TQ intervals. Under these conditions, AF was detected in less than 7 beats, with an accuracy higher than 90%, which is comparable to previous works. Conclusions: Unlike most of previous works, which were mainly based on quantifying the irregular ventricular response during AF, the proposed metric presents two major advan- tages. First, it can perform successfully even under heart rates with no variability. Second, it consists of a single metric, thus turning its clinical interpretation and real-time imple- mentation easier than previous methods requiring combined indices under complex classifiers., This work was supported by the projects TEC2014-52250-R from the Spanish Ministry of Economy and Competitiveness and PPII-2014-026-P from Junta de Comunidades de Castilla La Mancha.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Fusion of Scores in a Detection Context Based on Alpha Integration

  • Soriano Tolosa, Antonio
  • Ahmed, B.
  • Vergara Domínguez, Luís|||0000-0001-6803-4774
  • Salazar Afanador, Addisson|||0000-0001-5849-5104
We present a new method for fusing scores corresponding to different detectors (two hypotheses case). It is based on alpha integration, which we have adapted to the detection context. Three optimization methods are presented: least mean-square error, maximization of the area under the ROC curve and minimization of the probability of error. Gradient algorithms are proposed for the three methods. Different experiments with simulated and real data are included in the paper. Simulated data consider the two-detector case to illustrate the different factors influencing alpha integration and to demonstrate the improvements obtained by score fusion, with respect to the individual detector performance. Two real data cases have been considered. In the first one, multimodal biometric data have been processed. This case is representative of scenarios in which probability of detection is to be maximized for a given probability of false alarm. The second case is the automatic analysis of electroencephalogram and electrocardiogram records with the aim of reproducing the medical expert detections of arousals during sleeping. This case is representative of scenarios in which probability of error is to be minimized. The general superior performance of alpha integration verifies the interest of optimizing the fusing parameters., This work has been supported by Generalitat Valenciana under grants PROMETEOII 2014-032, ISIC2012-006 and by Spanish administration under grant TEC2014-58438-R.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

3D Simulation Modeling of UAV-to-Car Communications

  • HADIWARDOYO, SEILENDRIA ARDITYARAMA
  • Ji, Yusheng
  • Tavares De Araujo Cesariny Calafate, Carlos Miguel|||0000-0001-5729-3041
  • Cano, Juan-Carlos|||0000-0002-0038-0539
  • Hernández-Orallo, Enrique|||0000-0002-3284-561X
  • Manzoni, Pietro|||0000-0003-3753-0403
[EN] In this paper, we propose a realistic model for simulating communications between unmanned aerial vehicles (UAVs), or drones, and ground vehicles, which can support mobile infrastructure to broadcast alerts in emergency situations. Three-dimensional positioning features should be considered in these simulations that involve UAVs and ground vehicles since communications links are not based on a flat surface. In fact, irregular terrains in the form of hills and mountains can greatly affect the communications by acting as obstacles that block radio signals partially or totally. Hence, in this paper, we propose a simulation model that conforms to this kind of communication and that was developed in the scope of the OMNeT++ simulator. The simulation results achieved showed a great degree of similarities with those results obtained in a real testbed for different scenarios. In addition, various path loss models and elevation models were considered to improve the level of realism of the simulation model., This work was supported in part by the Japan Society for the Promotion of Science KAKENHI under Grant JP16H02817 and Grant JP18KK0279, in part by the International Internship Program of the National Institute of Informatics, Japan, and in part by the Ministerio de Economía y Competividad, Programa Estatal de Investigación, Desarollo e Innovación Orientada a los Retos de la Sociedad, Proyectos ICDCI 2014, Government of Spain, under Grant TEC2014-52690-R and Grant BES-2015-075988.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

An Analytical Solution for Radiofrequency Ablation with a Cooled Cylindrical Electrode

  • Romero-Méndez, Ricardo
  • Berjano, Enrique|||0000-0002-3247-2665
[EN] We present an analytical solution to the electrothermal mathematical model of radiofrequency ablation of biological tissue using a cooled cylindrical electrode. The solution presented here makes use of the method of separation of variables to solve the problem. Green's functions are used for the handling of nonhomogeneous terms, such as effect of electrical currents circulation and the nonhomogeneous boundary condition due to cooling at the electrode surface. The transcendental equation for determination of eigenvalues of this problem is solved using Newton's method, and the integrals that appear in the solution of the problem are obtained by Simpson's rule. The solution obtained here has the possibility of handling different functional dependencies of the source term and nonhomogeneous boundary condition. The solution provides a tool to understand the physics of the problem, as it shows how the solution depends on different parameters, to provide mathematical tools for the design of surgical procedures and to validate other modeling techniques, such as the numerical methods that are frequently used to solve the problem., This work was supported by the Universidad Autonoma de San Luis Potosi (Mexico), which granted Ricardo Romero-Mendez a sabbatical leave to do research in the field of biomedical engineering, and the Government of Spain through the "Plan Estatal de Investigacion, Desarrollo e Innovacion Orientada a los Retos de la Sociedad" (Grants TEC 2014-52383-C3-R and TEC 2014-52383-C3-1-R).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Information-Theoretic Analysis and Performance Evaluation of Optimal Demappers for Multi-Layer Broadcast Systems

  • Garro, Eduardo
  • Gimenez Gandia, Jordi Joan
  • Klenner, Peter
  • Gomez-Barquero, David|||0000-0003-2610-7765
[EN] Multi-layer broadcast systems distribute services across time and frequency domain by means of power-division multiplexing. Successive interference cancelation is required, in general, in order to extract the content of all services. For a low-complexity implementation, the receiver can obtain the strongest (top-layer) signal assuming underlying signals to behave like thermal noise. The thermal noise assumption may not be valid under certain conditions and a more accurate characterization of the interference could bring improved performance. This paper analyzes the validity of the noise-like assumption considering the power ratio between signals and the required carrier-to-noise ratio for error-free reception. The main contribution of the paper is the proposal of a demapping algorithm that exploits the knowledge of the constellation of underlying signals. Generalized mutual information, performance evaluation, and complexity analysis are provided with the additive white Gaussian noise-like assumptions and with the proposed alternative in order to assess the potential performance improvements that can be achieved., This work was supported by in part by the Ministerio de Educacion y Ciencia, Spain under Grant TEC2014-56483-R, and in part by the European FEDER Funds.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Demonstration of multiplexed sensor system combining low coherence interferometry and microwave photonics

  • Benítez, Jesús
  • Bolea, Mario
  • Mora Almerich, José|||0000-0002-2877-4118
[EN] In this work, a multiplexed sensor system is proposed by means of the combination of low coherence interferometry (LCI) and microwave photonics (MWP). Variations of physical magnitudes can be measured in an array of head sensors by monitoring the optical path difference generated by each sensor. In this case, the characterization of the multiplexed sensor system is done through the electrical transfer function corresponding to the MWP-LCI system. Moreover, the effect produced by the mutual interaction among head sensors is analyzed in this work. Experimental and theoretical demonstration of the system is provided comparing single detection and balanced detection approaches., National Project TEC2014-60378; Research Excellency Award Program GVA PROMETEO 2013/012.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Contribución de congreso (ConferenceOutput)

Numerical modeling of double-negative acoustic metamaterials: Should losses be included?

  • Cutanda Henriquez, Vicente
  • Andersen, Peter Risby
  • Sánchez-Dehesa Moreno-Cid, José|||0000-0003-0742-4407
[EN] Viscous and thermal losses of acoustic waves are usually neglected or accounted for as boundary impedance. It is known, however, that acoustic losses become relevant in devices with some dimension in the millimeter range or below. On the other hand, the new class of structures called acoustic metamaterials can be affected by acoustic losses, but in this case the extension of these effects is less known. Acoustic metamaterials are intricate periodic structures where, at frequencies low enough ( corresponding to wavelengths much l arger than the structure period), elementary units interact producing interesting unusual effects. In this paper advanced modeling tools based on the Boundary Element Method (BEM) and the Finite Element Method (FEM) are used to study the effect of losses in an acoustic metamaterial scaled to different sizes. The conclusions are expected to give insight on the practical limitations when using acoustic metamaterials, J. Sanchez-Dehesa acknowledges the support by the Spanish Ministerio de Economía y Competitividad, and the European Union Fondo Europeo de Desarrollo Regional (FEDER) through Project No. TEC2014-53088-C3-1-R
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Contribución de congreso (ConferenceOutput)

Performance of Hybrid Beamforming for mmW Multi-antenna Systems in Dense Urban Scenarios

  • Gimenez, Sonia
  • Roger, Sandra
  • Baracca, Paolo
  • Braun, Volker
  • Halbauer, Hardy
  • Martín-Sacristán, David|||0000-0002-7781-557X
  • Monserrat del Río, Jose Francisco|||0000-0001-8664-6408
[EN] Among the many proposals to meet the fifth generation (5G) data rate demands, current spectrum scarcity has motivated the use of millimeter-Wave (mmW) bands for cellular communication. It is well known that mmW communication involves many propagation challenges, which can be compensated through massive multi-antenna techniques. However, implementing fully digital precoding schemes with massive arrays entails huge complexity and costs, which have recently boosted the interest for hybrid beamforming solutions. Although hybrid schemes have shown good performance in simplified setups, their suitability for realistic cellular systems with many interfering base stations and users is still unclear. In this sense, this paper assesses the performance of hybrid beamforming in a dense urban cellular system with a realistic mmW channel model and shows that it can reach the performance of fully digital maximum ratio transmission under line of sight conditions and with a sufficient number of parallel radio-frequency chains. Another important result is that multi-user hybrid beamforming provides a substantial capacity increase with respect to its single-user (SU) counterpart. This finding complements the views on mmW communication usage, which has been so far mainly intended for SU communication to provide high beamforming gains., The research done by P. Baracca, V. Braun, and H. Halbauer leading to these results received funding from the European Commission H2020 programme under grant agreement number 671650 (mmMAGIC project). The work carried out at the Universitat Politecnica de Valencia was supported by the Ministerio de Economia y Competitividad, Spain (TEC2014-60258-C2-1-R), by the European FEDER funds.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

MIMO Sphere Decoding With Successive Interference Cancellation for Two-Dimensional Non-Uniform Constellations

  • Barjau-Estevan, Carlos Salvador|||0000-0002-4258-6113
  • Gomez-Barquero, David|||0000-0003-2610-7765
  • Fuentes, Manuel
  • Shitomi, Takuya
[EN] Non-uniform constellations (NUCs) have been introduced to improve the performance of quadrature amplitude modulation constellations. 1D-NUCs keep the squared shape, while 2D-NUCs break that constraint to provide robustness. An impending problem with multiple-input multiple-output (MIMO) is the optimum demapping complexity, which grows exponentially with the number of antennas and the constellation order. Some well-known sub-optimum MIMO demappers, such as soft fixed-complexity sphere decoders (SFSD), can reduce that complexity. However, SFSD demappers do not work with the 2D-NUCs, since they perform a quantization step in separated I/Q components. In this letter, we provide an efficient solution for the 2D-NUCs based on Voronoi regions. Both complexity implications and SNR performance are also analyzed., This work was partially supported by the Ministry of Economy and Competitiveness of Spain (TEC2014-56483-R), co-funded by the European FEDER fund.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Long Period Gratings in Multicore Optical Fibers for Directional Curvature Sensor Implementation

  • Barrera Vilar, David|||0000-0002-1700-6842
  • Madrigal-Madrigal, Javier|||0000-0003-3156-1321
  • Sales Maicas, Salvador|||0000-0001-9457-976X
[EN] Multicore optical fibers are especially attractive for the fabrication of curvature and shape sensors due to the spatial distribution of the different cores. Fiber Bragg gratings have been used in the past for the implementation of these sensors, however, despite their inherent properties, they have a very limited sensitivity. In this paper, we study the use of long period gratings (LPGs) for the implementation of a directional curvature sensor. We inscribed a set of three different LPGs in a seven core optical fiber using a selective inscription technique. We inscribed a single LPG in the external cores and an array of three LPGs in the central core. We have characterized the proposed sensor for strain, torsion, and curvature magnitude and direction. The proposed sensor shows a linear response for curvature magnitudes from 0 to 1.77 m(-1) with a maximum curvature sensitivity of -4.85 nm/m(-1) and shows a near sinusoidal behavior in all the cores with curvature directions from 0 degrees to 360 degrees. The sensor shows a good insensitivity to strain. The torsion in the multicore optical fibers can be detected and measured using the maximum attenuation of the LPGs in the external cores., This work was supported in part by the Sistema Nacional de Garantia Juvenil under Grant PEJ-2014-A-75865 (Promocion de Empleo Joven e Implantacion de la Garantia Juvenil 2014, MINECO), in part by the Ministry of Economy and Competitiveness under Project TEC2014-60378-C2-1-R, in part by the FINESSE the European Union's Horizon 2020 research and innovation programme under the Marie Sklodowska-Curie Action Grant 722509, and in part by the Generalitat Valenciana under Grant APOSTD/2016/015.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Advanced RF Interferometry Structure for Improving Operation Range

  • Benítez-González, Jesús
  • Mora Almerich, José|||0000-0002-2877-4118
[EN] In this letter, a novel structure combining low coherence interferometry (LCI) and microwave photonics (MWP) is proposed. In this case, the electro-optic modulator is strategically placed inside the interferometric structure in order to modify the behavior of the whole MWP-LCI system. Specifically, limiting effects which are inherently generated as the DC term, the self-reflection term and the carrier suppression effect are avoided. This fact enables the improvement of the MWP-LCI operating range in comparison to previous proposals. Moreover, a detailed description of the MWP-LCI structure is addressed in this letter to support the corresponding experimental demonstration and theoretical development. In addition, typical LCI capabilities such as penetration depth, resolution, and sensitivity are also measured. For the MWP-LCI structure proposed here, a 1 cm penetration depth with a resolution of 120 mu m and a sensitivity beyond 50 dB are achieved., This work was supported in part by the National Project TEC2014-60378 through the Ministerio de Ciencia y Tecnologia and in part by the Regional Project PROMETEO FASE II/2013/012 through the Generalitat Valenciana. (Corresponding author: J. Mora.)
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Wideband Broadcasting: A Power-Efficient Approach to 5G Broadcasting

  • Gimenez Gandia, Jordi Joan
  • Mogarde, Javier
  • Stare, Erik
  • Gomez-Barquero, David|||0000-0003-2610-7765
[EN] Efficient and flexible use of spectrum will be inherent characteristics of fifth-generation (5G) communication technologies with native support of wideband operation with frequency reuse 1, i.e. all transmit sites use all available frequency resources. Although not from the very first 5G release of 3GPP (Third Generation Partnership Project), it is expected that broadcast/multicast technology components will later be added and fully integrated in the 5G system. The combination of both wideband and frequency reuse 1 may provide significant gains for broadcast transmissions in terms of energy efficiency, since it is more efficient to increase capacity by extending the bandwidth rather than increasing the transmit power over a given bandwidth. This breaks with the traditional concept of terrestrial broadcast frequency planning, and paves the way to new potential uses of UHF (Ultra High Frequency) spectrum bands for 5G broadcasting. This paper provides an insight into the fundamental advantages in terms of capacity, coverage as well as power saving of wideband broadcast operation. The role of the network deployment, linked to frequency reuse in the UHF band, and its influence in the performance of a Wideband Broadcasting system are discussed. The technical requirements and features that would enable such power-efficient solution are also addressed., This work was supported in part by the European Commission under the 5G-PPP project 5G-Xcast (H2020-ICT-2016-2 call, grant number 761498). The views expressed in this contribution are those of the authors and do not necessarily represent the project. This work was also partially supported by the Ministerio de Educacion y Ciencia, Spain (TEC2014-56483-R), co-funded by European FEDER funds.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Estimating the Laplacian matrix of Gaussian mixtures for signal processing on graphs

  • Belda, Jordi
  • Safont Armero, Gonzalo
  • Vergara Domínguez, Luís|||0000-0001-6803-4774
  • Salazar Afanador, Addisson|||0000-0001-5849-5104
[EN] Recent works in signal processing on graphs have been driven to estimate the precision matrix and to use it as the graph Laplacian matrix. The normalized elements of the precision matrix are the partial correlation coefficients which measure the pairwise conditional linear dependencies of the graph. However, the non-linear dependencies inherent in any non-Gaussian model cannot be captured. We propose in this paper a generalized partial correlation coefficient which is derived by assuming an underlying multivariate Gaussian Mixture Model of the observations. Exact and approximate methods are proposed to estimate the generalized partial correlation coefficients from estimates of the Gaussian Mixture Model parameters. Thus it may find application in any non-Gaussian scenario where the Laplacian matrix is to be learned from training signals. (C) 2018 Elsevier B.V. All rights reserved., This work was supported by Spanish Administration (Ministerio de Economia y Competitividad) and European Union (FEDER) under grant TEC2014-58438-R, and Generalitat Valenciana under grant PROMETEO II/2014/032.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Experimental measurement of plasmonic nanostructures embedded in silicon waveguide gaps

  • Espinosa-Soria, Alba
  • Griol Barres, Amadeu
  • Martínez, Alejandro|||0000-0001-5448-0140
In this work, we report numerical simulations and experiments of the optical response of a gold nanostrip embedded in a silicon strip waveguide gap at telecom wavelengths. We show that the spectral features observed in transmission and reflection when the metallic nanostructure is inserted in the gap are extremely different than those observed in free-space excitation. First, we find that interference between the guided field and the electric dipolar resonance of the metallic nanostructure results in highcontrast (> 10) spectral features showing an asymmetric Fano spectral profile. Secondly, we reveal a crossing in the transmission and reflection responses close to the nanostructure resonance wavelength as a key feature of our system. This approach, which can be realized using standard semiconductor nanofabrication tools, could lead to a full exploitation of the extreme properties of subwavelength metallic nanostructures in an on-chip configuration, with special relevance in fields such as biosensing or optical switching., We acknowledge support from the Spanish Ministry of Economy and Competiveness (MINECO) under grants TEC2014-51902-C2-1-R and TEC2014-61906-EXP, and the Valencian Conselleria d'Educacion, Cultura i Esport under grant PROMETEOII/2014/034.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

OOFDM signal transmission using a single optical broadband source

  • Chicharro, Francisco I.|||0000-0001-9116-2870
  • Ortega Tamarit, Beatriz|||0000-0003-1196-4756
  • de Diego Antón, María|||0000-0001-9948-3396
  • Mora Almerich, José|||0000-0002-2877-4118
[EN] In this letter, optical OFDM signal transmission is demonstrated by using a broadband optical source over a 10 km fiber link. OFDM signal transmission usually employs lasers to generate the optical carrier since the chromatic fiber dispersion prevents the use of broadband optical sources. However, an interferometric system is introduced to allow signal transmission at a given RF band when a broadband optical source is employed. Optical sources with different optical bandwidths have been employed to explore the limitations of the system. OFDM transmission at 2 Gb/s using both QPSK and 16QAM modulation is demonstrated over 10 km., This work was supported in part by the National Project MINECO under Grant TEC2014-60378-C2-1-R MEMES and in part the Regional GVA funded Prometeo 2013/012 Project on Next Generation Microwave Photonic technologies.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Contribución de congreso (ConferenceOutput)

Localization for capsule endoscopy at UWB frequencies using an experimental multilayer phantom

  • Barbi, Martina
  • Pérez Simbor, Sofía
  • Andreu Estellés, Carlos
  • Garcia-Pardo, Concepcion|||0000-0002-2774-980X
  • Cardona Marcet, Narciso|||0000-0001-5697-1453
[EN] Localization inside the human body using ultrawideband (UWB) wireless technology is gaining importance in several medical applications such as capsule endoscopy. Performance analysis of RF based localization techniques are mainly conducted through simulations using numerical human models or through experimental measurements using homogeneous phantoms. One of the most common implemented RF localization approaches uses the received signal strength (RSS). However, to the best of our knowledge, no experimental measurements employing multilayer phantoms are currently available in literature. This paper investigates the performance of RSS-based technique for two-dimensional (2D) localization by employing a two-layer experimental phantom-based setup. Preliminary results on the estimation of the in-body antenna coordinates show that RSS-based method can achieve a location accuracy on average of 0.5-1 cm within a certain range of distances between in-body and on-body antenna., This work was supported by the European Union’s H2020:MSCA:ITN program for the ”Wireless In-body Environment Communication- WiBEC” project under the grant agreement no. 675353. This work was also funded by the Programa de Ayudas de Investigación y Desarrollo (PAID-01-16) from Universitat Politècnica de València and by the Ministerio de Economía y Competitividad, Spain (TEC2014-60258-C2-1-R), by the European FEDER funds.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Capítulo o parte de un libro (BookPart)

Experimental Evaluation of a Low-Cost Digital Sign-Posts Architecture for ITS Applications

  • FERNANDEZ LAGUIA, CARLOS JAVIER
  • Cano, Juan-Carlos|||0000-0002-0038-0539
  • Tavares De Araujo Cesariny Calafate, Carlos Miguel|||0000-0001-5729-3041
  • Manzoni, Pietro|||0000-0003-3753-0403
Integrating road signs information is becoming a critical goal for Intelligent Transportation Systems (ITS). Unlike other driving automation features, this capacity requires not only the vehicle, but also posts and infrastructure to be adapted thus involving an investment that can only be justified by a substantial number of users. In this paper we describe an architecture that aims to facilitate the introduction and deployment of this technology based on low cost devices as the digital sign-posts and the integration of smartphones as an alternative in-vehicle user-interface. Wireless communications based on IEEE 802.11 is used for the basic connectivity requirements. From the results obtained through an experimental evaluation, we show that, despite the smartphone constraints, we can achieve successful detection and recognition experiences at up to 90 km/h. Ultimately the experiment described confirms that the use of smartphones represents an opportunity to expand wireless technology in the traffic sign digitalisation area., This work was partially supported by the Ministerio de Economía y Competitividad, Programa Estatal de Investigación, Desarrollo e Innovación Orientada a los Retos de la Sociedad, Proyectos I+D+I 2014, Spain, under Grant TEC2014-52690-R.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Scattered Pilot Performance and Optimization for ATSC 3.0

  • Garro, Eduardo
  • Gimenez, Jordi Joan
  • Park, Sung Ik
  • Gomez-Barquero, David|||0000-0003-2610-7765
[EN] The next-generation U.S. digital terrestrial television (DTT) standard ATSC 3.0 is the most flexible DTT standard ever developed, outperforming the state-of-the-art digital video broadcasting-terrestrial 2nd generation (DVB-T2) standard. This higher flexibility allows broadcasters to select the configuration that better suits the coverage and capacity requirements per service. Regarding the selection of pilot patterns, whereas DVB-T2 provides eight different patterns with a unique pilot amplitude, ATSC 3.0 expands up to 16, with five different amplitudes per pattern. This paper focuses on the pilot pattern and amplitude performance and optimization for time and power multiplexing modes, time division multiplexing and layered division multiplexing (LDM), respectively, of ATSC 3.0. The selection of the optimum pilot configuration is not straightforward. On the one hand, the pilots must be sufficiently dense to follow channel fluctuations. On the other hand, as long as pilot density is increased, more data overhead is introduced. Moreover, this selection is particularly essential in LDM mode, because the LDM implementation in ATSC 3.0 requires that both layers share all the waveform parameters, including pilot pattern configuration. In addition, there is an error proportional to the channel estimate of the top layer that affects to the lower layer performance., This work was supported in part by the Institute for Information and Communications Technology (IITP) by the Korea Government (MSIP) (Development of Service and Transmission Technology for Convergent Realistic Broadcast) under Grant R0101-15-294, and in part by the Ministerio de Educación y Ciencia, Spain, by European FEDER Funds under Grant TEC2014-56483-R.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

UWB Pulses Generation and Modulation Through a Customized FBG-Based Photonic Device

  • Moreno, Vanessa
  • Muriel, M.A.
  • Mora Almerich, José|||0000-0002-2877-4118
  • Barrera Vilar, David|||0000-0002-1700-6842
  • Capmany Francoy, José|||0000-0002-6460-4167
In this letter, we propose and experimentally demonstrate an efficient and scalable photonic superstructure employed for ultrawideband (UWB) pulses modulation purposes. This design is based on the combination of a phase modulation to intensity modulation stage with a customized pulse shaper. Pulse shaping is achieved by means of a photonic structure composed by concatenated fiber Bragg gratings. The proposed scheme holds the capacity of generating high-order UWB signals, a feature that enables the implementation of widely employed modulation formats such as: pulse position modulation, pulse shape modulation, and bi-phase modulation. Theoretical and experimental measurements are exposed to sustain the validity of this system., This work was supported in part by the Ministerio de Ciencia y Tecnologia under Grant TEC2014-60378-C2-1-R and Grant TEC2014-58048-C2-2-P and in part the Regional Project PROMETEO FASE II/2013/012 through the Generalitat Valenciana.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

(Invited) Cascade FBGs distributed sensors interrogation using microwave photonics filtering techniques

  • Ricchiuti, Amelia Lavinia
  • Hervás-Peralta, Javier
  • Sales Maicas, Salvador|||0000-0001-9457-976X
Systems to interrogate photonic sensors based on long fiber Bragg gratings (FBGs) are illustrated and experimentally validated. The FBGs-based devices are used as quasi-distributed sensors and have demonstrated their ability to detect and measure the precise location of several spot events. The principle of operation is based on a technique used to analyze microwave photonics (MWP) filters. The overall idea beyond this work has been borne out and demonstrated step by step starting from preliminary test that have led to the development of a very-long distributed sensor based on an array of 500 equal and weak FBGs. Firstly, we have demonstrated the feasibility of the MWP filtering technique to interrogate a 10 cm-long high reflectivity (&#8776;99%) FBG. Then, a pair of low-reflectivity (<6%) FBGs has been employed as sensing device. The latter has laid the foundation for the development and implementation of a 5 m-long fiber optic sensor based on 500 very weak FBGs. Spot events have been detected with a good spatial accuracy of less than 1 mm using a modulator and a photo-detector (PD) with a modest bandwidth of only 500 MHz. The simple proposed schemes result cost effective, intrinsically robust against environmental changes and easy to reconfigure., This work was support by the Accion Financiada por el Ministerio de Educacion, Cultura y Deporte within the framework of the Programa de Campus de Excelencia Internacional VLC/Campus, by the Spanish MINECO through projects TEC2014-60378-C2-1-R, by the Grant of the program SANTIAGO GRISOLIA (Grant number GRISOLIA/2013/034), and by the Research Excellency Award Program GVA PROMETEO 2013/012.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Endoluminal radiofrequency ablation of the main pancreatic duct is a secure and effective method to produce pancreatic atrophy and to achieve stump closure

  • Andaluz, Anna
  • Ewertowska, Elzbieta
  • Moll, Xavier
  • Aguilar, Adrià
  • García, Félix
  • Fondevila, Dolors
  • Quesada, Rita
  • Grande, Luís
  • Burdío, Fernando
  • Berjano, Enrique|||0000-0002-3247-2665
[EN] Radiofrequency energy has been used both experimentally and clinically to manage the pancreatic remnant after distal pancreatectomies. Our goal was to determine whether endoluminal radiofrequency (RF) ablation of the main pancreatic duct in large animals would be more efficient than glue occlusion as an exocrine pancreatic atrophy-inducing procedure. Thirty-four Landrace pigs were assigned to either the transpapilar (n = 16) or transection (n = 18) groups. The transection implied the pancreas neck was severed. In each of these groups the remaining distal pancreatic duct was occluded either by RF or by glue. In the transpapilar group complete atrophy was observed in all the RF cases, while atrophy was incomplete in all the members of the glue subgroup. The failure rate of the main pancreatic duct (usually expressed by a pseudocyst) in the transection groups was dramatically higher in the glue subgroup than the RF subgroups (9 out of 9 and 1 out of 9, respectively) and postoperative mortality occurred only in the glue subgroup (3 out of 9). These results show the superiority of endoluminal RF ablation over glue for main pancreatic duct occlusion, as seen by the degree of atrophy and fewer postoperative pancreatic fistulas., This work was supported by the Spanish Ministerio de Economia, Industria y Competitividad under the "Plan Estatal de Investigacion, Desarrollo e Innovacion Orientada a los Retos de la Sociedad" Grant TEC2014-52383-C3-R (TEC2014-52383-C3-1-R and TEC2014-52383-C3-3-R). Elzbieta Ewertowska has a Predoctoral Grant (BES-2015-073285) from the Ministry of Economy, Industry and Competitiveness (Government of Spain).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Laparoscopic partial splenectomy for giant cyst using a radiofrequency-assisted device: a case report

  • Quesada, Rita
  • Poves, Ignasi
  • Iglesias, Mar
  • Grande, Luis
  • Burdío, Fernando
  • Berjano, Enrique|||0000-0002-3247-2665
[EN] Background Although radiofrequency-assisted devices have sometimes been used in partial splenectomy, this is not a common technique. This report describes the first case of laparoscopic partial splenectomy using an RF-assisted device (Coolinside) which allows both coagulation and transection of the parenchyma and eventually the protective coagulation of the remnant side. Case presentation A 27-year-old woman was found to have a giant hydatic cyst measuring 12.0¿×¿14.0¿×¿16.6 cm that mainly occupied the lower pole of the spleen and retroperitoneal space. The patient underwent a laparoscopic partial splenectomy using an RF-based device designed to accomplish both the coagulation and dissection of the splenic tissue. The estimated blood loss was less than 200 mL. Conclusions Even though RF ablation has traditionally been used for hepatic parenchymal transection, it seems equally suited to partial splenectomy. This device seems to provide good results, minimizing blood loss during partial splenectomy; however, randomized trials will be necessary to see if the results are superior to those of other techniques., This work was partially supported by the Spanish“Programa Estatal deInvestigación, Desarrollo e Innovación Orientada a los Retos de la Sociedad” under Grant TEC2014-52383-C3-R (TEC2014-52383-C3-1-R and TEC2014-52383-C3-3-R).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

A Survey and Comparative Study of Broadcast Warning Message Dissemination Schemes for VANETs

  • Sangüesa-Escorihuela, Julio Alberto
  • Fogue, Manuel
  • Garrido, Piedad
  • Martinez Dominguez, Francisco Javier
  • Cano, Juan-Carlos|||0000-0002-0038-0539
  • Tavares De Araujo Cesariny Calafate, Carlos Miguel|||0000-0001-5729-3041
Vehicle-to-vehicle (V2V) communications also known as vehicular ad hoc networks (VANETs) allow vehicles to cooperate to increase driving efficiency and safety on the roads. In particular, they are forecasted as one of the key technologies to increase traffic safety by providing useful traffic services. In this scope, vehicle-to-vehicle dissemination of warning messages to alert nearby vehicles is one of the most significant and representative solutions. The main goal of the different dissemination strategies available is to reduce the message delivery latency of such information while ensuring the correct reception of warning messages in the vehicle's neighborhood as soon as a dangerous situation occurs. Despite the fact that several dissemination schemes have been proposed so far, their evaluation has been done under different conditions, using different simulators, making it difficult to determine the optimal dissemination scheme for each particular scenario. In this paper, besides reviewing the most relevant broadcast dissemination schemes available in the recent literature, we also provide a fair comparative analysis by evaluating them under the same environmental conditions, focusing on the same metrics, and using the same simulation platform. Overall, we provide researchers with a clear guideline of the benefits and drawbacks associated with each scheme., This work was partially supported by the Ministerio de Economia y Competitividad, Programa Estatal de Investigacion, Desarrollo e Innovacion Orientada a los Retos de la Sociedad, Proyectos I+D+I 2014, Spain, under Grant TEC2014-52690-R, and by the Government of Aragon and the European Social Fund (T91 Research Group).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Contribución de congreso (ConferenceOutput)

Impact of Receivers Location on the Accuracy of Capsule Endoscope Localization

  • Barbi, Martina
  • Andrea Nevárez
  • Vicente Pons Beltrán
  • Frasson, Matteo
  • Garcia-Pardo, Concepcion|||0000-0002-2774-980X
  • Cardona Marcet, Narciso|||0000-0001-5697-1453
[EN] In recent years, localization for capsule endoscopy applications using Ultra-Wideband (UWB) technology has become an attractive field of study due to its potential benefits for patients. Performance analysis of RF-based localization techniques are very limited in literature. Most of the available studies rely on software simulations using digital human models. Nonetheless, no realistic studies based on in-vivo measurements has been reported yet. This paper investigates the performance of RSS-based technique for three-dimensional (3D) localization in the UWB frequency band. Impact of receivers selection as well as of the evaluated path loss model on the localization accuracy is investigated. Results obtained through CST-based simulations and from recently conducted in-vivo measurements are presented and compared., This work was supported by the European Union's H2020:MSCA:ITN program for the "Wireless In-body Environment Communication- WiBEC" project under the grant agreement no. 675353. This work was also funded by the Ministerio de Economia y Competitividad, Spain (TEC2014-60258-C2-1-R), by the European FEDER funds.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Theoretical study of platonic crystals with periodically structured N-beam resonators

  • Gao, Penglin
  • Wu, Linzhi
  • Climente Alarcón, Alfonso
  • Sánchez-Dehesa Moreno-Cid, José|||0000-0003-0742-4407
[EN] A multiple scattering theory is applied to study the properties of flexural waves propagating in a plate with periodically structured N-beam resonators. Each resonator consists of a circular hole containing an inner disk connected to background plate with N rectangular beams. The Bloch theorem is employed to obtain the band structure of a two-dimensional lattice containing a single resonator per unit cell. Also, a numerical algorithm has been developed to get the transmittance through resonator slabs infinitely long in the direction perpendicular to the incident wave. For the numerical validation, a square lattice of 2-beam resonators has been comprehensively analyzed. Its band structure exhibits several flat bands, indicating the existence of local resonances embedded in the structure. Particularly, the one featured as the fundamental mode of the inner disk opens a bandgap at low frequencies. This mode has been fully described in terms of a simple spring-mass model. As a practical application of the results obtained, a homogenization approach has been employed to design a focusing lens for flexural waves, where the index gradient is obtained by adjusting the orientation of the resonators beams. Numerical experiments performed within the framework of a three-dimensional finite element method have been employed to discuss the accuracy of the models described here. Published by AIP Publishing., This work was supported by the Ministerio de Economia y Competitividad of the Spanish government and the European Union Fondo Europeo de Desarrollo Regional (FEDER) through Project No. TEC2014-53088-C3-1-R, and the National Science Foundation of China under Grant No. 11432004. Penglin Gao acknowledges a scholarship with No. 201606120070 provided by China Scholarship Council.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

KLT Based Interrogation Technique for FBG Multiplexed Sensor Tracking

  • Hervás-Peralta, Javier
  • Tosi, Daniele
  • García-Miquel, Héctor
  • Fernandez-Pousa, Carlos R.
  • Barrera Vilar, David|||0000-0002-1700-6842
  • Sales Maicas, Salvador|||0000-0001-9457-976X
[EN] The Karhunen-Loeve transform (KLT) is used to retrieve the wavelength information of several fiber Bragg gratings (FBGs) that are acting as a multiplexed sensor. The modulated light of a broadband source is launched to the FBG cascade in order to capture the electrical frequency response of the system. Thanks to a dispersive media, the wavelengths of the FBGs are mapped in radiofrequency (RF) delays. Wavelength changes are determined by the amplitude change of the samples in the impulse response, a change which is followed by the eigenvalue calculated by the KLT routine. The use of the KLT routine reduces by three orders of magnitude the amount of points needed to have a sub-degree resolution in temperature sensing, while keeping the accuracy almost intact., This work was supported in part by the Spanish MINECO through Project TEC2014-60378, and in part by the Government of Valencia through the Research Excellency Award Program GVA PROMETEO 2013/012. The work of J. Hervas was supported by the MECD FPU Scholarship (FPU13/04675).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Zero-phase propagation in realistic plate-type acoustic metamaterials

  • Malléjac, M.
  • Merkel, A.
  • Christensen, J.
  • Tournat, V.
  • Groby, Jean-Philippe
  • Sánchez-Dehesa Moreno-Cid, José|||0000-0003-0742-4407
  • Romero-García, Vicente|||0000-0002-3798-6454
[EN] We theoretically, numerically, and experimentally analyze the Density-Near-Zero (DNZ) regime of a one-dimensional acoustic metamaterial. This acoustic metamaterial is composed of thin elastic plates periodically clamped in an air-filled waveguide, and the effective dynamic zero mass density is obtained from the strong dispersion around the bandgaps associated with the resonances of the plates. We emphasize the importance of the impedance mismatch between the acoustic metamaterial and the surrounding waveguide at the frequency of the zero effective density in addition to the consequences of the inherent losses. As a result, the frequency of the zero phase propagation, i.e., the acoustic propagation with zero phase delay, is not exactly the frequency of the zero density and lies in the frequency bandgap where the effective density is negative. Considering these limitations, the zero phase propagation is still experimentally observed and a subwavelength acoustic dipole is numerically designed, thus demonstrating the possible realistic implementations of DNZ acoustic metamaterials., This article is based upon work from COST Action DENORMS CA15125, supported by COST (European Cooperation in Science and Technology). This work was funded by the Metaroom Project No. ANR-18-CE08-0021 and co-funded by ANR and RCG. J. Christensen acknowledges the support from the MINECO through a Ramon y Cajal grant (Grant No. RYC-2015-17156). J. Sanchez-Dehesa acknowledges the support from the Ministerio de Economia y Competitividad of the Spanish government and the European Union Fondo Europeo de Desarrollo Regional (FEDER) through Project No. TEC2014-53088-C3-1-R.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Layered Division Multiplexing with Distributed Multiple-Input Single-Output Schemes

  • Garro, Eduardo
  • Kim, Jeongchang
  • Park, Sung-Ik
  • Hur, Namho
  • Barjau-Estevan, Carlos Salvador|||0000-0002-4258-6113
  • Gomez-Barquero, David|||0000-0003-2610-7765
[EN] Single frequency networks (SFNs) provides an increased spectral efficiency compared to the traditional multiple frequency networks. However, some coverage areas in SFN can be affected by destructive interferences. In order to reduce these situations, distributed multiple-input single-output (MISO) schemes have been adopted in the new digital terrestrial television standards, Alamouti in DVB-T2 and transmit diversity code filter sets in ATSC 3.0. On the other hand, layered division multiplexing (LDM), a non-orthogonal multiple access technology, has been adopted in ATSC 3.0 due to its spectral efficiency increase compared to time or frequency division multiplexing. The LDM signal is formed by a power superposition of two independent signals, which are designed for different reception conditions (mobile and fixed-rooftop). The combination of distributed MISO and LDM techniques has not been evaluated yet. In this paper, the joint transmission of LDM with distributed MISO is analyzed in terms of complexity and the joint performance is evaluated by means of physical layer simulations., This work was supported in part by the ICT Research and Development Program of MSIP/IITP (Development of Transmission Technology for Ultra High Quality UHD) under Grant 2017-0-00081, and in part by the Ministerio de Educacion y Ciencia, Spain, through European FEDER funds under Grant TEC2014-56483-R.