Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 62
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Development and Characterization of Environmentally Friendly Insulation Materials for the Building Industry from Olive Pomace Waste

  • Gutierrez, O.
  • Fages, E.
  • Balart, Rafael|||0000-0001-5670-7126
  • Lascano-Aimacaña, Diego Sebastián|||0000-0002-0996-1946
  • Quiles-Carrillo, Luis|||0000-0001-8037-2215
  • Sanchez-Nacher, Lourdes|||0000-0002-8627-4576
[EN] This work is focused on the upgrading olive oil pomace to obtain high environmentally friendly insulation materials for the construction and building industry. Upgrading of these wastes has been carried out by using the wet-laid technology in combination with different thermoplastic binder fibers both from natural and synthetic origin. After the wetlaid process, the obtained veils or non-wovens were subjected to different processes: a hot-press moulding process or a continuous lamination process. The acoustic insulation properties were obtained by the Kundt¿s tube while the thermal insulating properties were obtained through determining heat transmission resistance (R) and heat absorption parameter (¿). These tests have revealed the excellent insulation properties of the olive pomace-derived materials, specifically, those based on high surface density non-wovens. The complementary process that follows wet-laid, i.e. hot-press moulding or continuous lamination process has a remarkable effect on insulation behaviour. In particular, the hot-pressed materials from olive pomace show better acoustic insulation while the continuously laminated materials offer the best thermal insulation properties., This research was supported by the Ministry of Science, Innovation, and Universities (MICIU) through the MAT201784909-C2-2-R program number. O. Gutierrez and E. Fages want to thank AITEX (Textile Research Institute) and the Institut Valencia de Competitivitat Empresarial (IVACE) for providing funds and equipment to develop this study within the framework of the ECOMATEX project research and development of technical, functional and sustainable materials applicable to the field of Green Cities (IMAMCI/2016/1). L. Quiles-Carrillo thanks Generalitat Valenciana (GVA) for his FPI grant (ACIF/2016/182) and the Spanish Ministry of Education, Culture, and Sports (MECD) for his FPU grant (FPU15/03812). D. Lascano acknowledges UPV for the grant received though the PAID-01-18 program.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Effects of bonding on the performance of optical fiber strain sensors

  • Floris, Ignazio
  • Sangiorgio, Valentino
  • Uva, Giuseppina
  • Rapido, Monica
  • Adam, Jose M|||0000-0002-9205-8458
  • Calderón García, Pedro Antonio|||0000-0002-9783-9333
  • Madrigal-Madrigal, Javier|||0000-0003-3156-1321
[EN] The structural health monitoring (SHM) of existing buildings, structures, and infrastructures has become increasingly important in recent years, while the interest of the scientific community is focused on the use of new high-performance technologies. Fiber optic sensors have become particularly attractive, thanks to their potential for monitoring strain in smart structures. The performance of this new technology depends to a large extent on the bonding technique used for its manufacture. Although the related literature has identified a correlation between some efficiency issues and the geometrical parameters of the bonding and mechanical properties of the materials adopted, the phenomenon is still not completely understood. This paper describes an in-depth study of the geometrical and mechanical parameters that influence the efficiency of optical fiber point sensors' surface bonding by synergistically related techniques such as computational simulation, experimental tests, sensor manufacturing, and data analysis. The paper's novelty is fourfold: (1) the investigation of the strain transfer mechanism of surface-bonded fiber optic sensors by considering, for the first time, all the parameters influencing the phenomenon through a considerable number of finite element (FE) analyses (117 three-dimensional FE models); (2) the development of a series of bonding efficiency predictive models; (3) the design of a specific laboratory test to validate the computational outcomes; and (4) the definition of useful guidelines for effective bonding manufacturing in order to maximize the performance of these sensors when acquiring monitoring data., Project Manufacturing Education and Training Governance Model; Universitat Politecnica de Valencia, Grant/Award Number: PAID-01-18; Spanish Ministry of Economy and Competitiveness, Grant/Award Number: DIMENSION TEC2017-88029-R; H2020 Marie SklodowskaCurie Actions, Grant/Award Number: 722509
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Effect of natural and forced charge air humidity on the performance and emissions of a compression-ignition engine operating at high warm altitude

  • Serrano, J.R.|||0000-0003-0692-3917
  • Martín, Jaime|||0000-0002-0496-3176
  • Piqueras, P.|||0000-0002-3767-0839
  • Tabet-Aleixandre, Roberto
  • Gómez-Gil, Javier
[EN] The effect of ambient humidity on the performance and pollutant emissions of internal combustion engines is not considered in the literature despite type-approval criteria are moving closer to real driving conditions. This work analyses experimentally the effects of charge air humidity at high warm altitudes, where the use of exhaust gas recirculation (EGR) is typically lowered and even avoided to recover engine performance at the expense of NOx emissions increase, on the response of a compression-ignition engine under a wide range of steady-state con-ditions in terms of engine-out emissions and specific fuel consumption. The impact of specific humidity varia-tions within the atmospheric range was analysed by coupling the engine to an altitude simulator with pressure, temperature, and humidity control capabilities. High altitudes and warm & high ambient temperatures were explored (2000 m at 30 degrees C and 2500 m at 45 degrees C) to cover ambient specific humidity up to 30 gwater/kgdry_air. In addition, the effects of increasing the specific humidity above the atmospheric levels were considered at 2500 m and 45 degrees C to emulate forced injection of water in the engine intake line corresponding to 60 gwater/kgdry_air. With this approach, understanding of the role of humidity is provided to highlight its importance as additional ambient property in emission control. In parallel, the assessment of the forced water content increase to control NOx emissions when EGR must be lowered was performed due to the altitude impact on the engine performance and turbocharger limits. The results showed a consistent and significant reduction in engine-out NOx emissions as the ambient humidity increased, reaching up to 300% with respect to the dry case, caused by the decrease in O2 availability due to the water content increase. The benefits of high humidity in NOx emission control at high altitudes when EGR is not feasible were complemented by an improved trade-off with particulate matter emission compared to the standard from EGR use. The results evidenced a reduction in opacity close to 250% for a given engine-out NOx emission when EGR was replaced by water content. By contrast, the slowdown of the combustion process as the fresh air humidity increased deteriorated the specific fuel consumption significantly as the engine load and speed increased. Nevertheless, these penalties ranged from 2 to 2.7% in the worst conditions and showed the same sensitivity for EGR and humidity increases., This research has been supported by Grant PID2020-114289RB-I00 funded by the Spanish Ministerio de Ciencia e Innovacion - Agencia Estatal de Investigacion (MCIN/AEI/10.13039/501100011033). The PhD candidate Roberto Tabet has been funded by Universitat Politecnica de Valencia through grant PAID -01-18.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Design of a Bubble Reactor for Altitude Simulators Used to Humidify a Combustion Air Stream by Means of CFD Multi-Phase Models

  • Serrano, J.R.|||0000-0003-0692-3917
  • Gil, A.|||0000-0001-7192-6992
  • Quintero-Igeño, Pedro-Manuel|||0000-0003-4373-2079
  • Tabet-Aleixandre, Roberto
  • Gómez, Javier
[EN] In this paper, a procedure for the design of a bubble reactor which allows the control of the humidity of a gas stream used as combustion air is presented. This reactor is designed to be used as a component of an altitude simulator test facility for the optimization, homologation and calibration of new hybrid engines. The design has been carried out by means of Computational Fluid Dynamics (CFD) multi-phase models and validated against the experimental data obtained from the developed prototype. A discussion about the adequate mesh topology and cell size is presented, as well as a comparison between the two available models for the air-water interphase. Lastly, a validation of the CFD results using experimental data shows that the model that should be used is the multi-regime interaction model, from which the final design for the bubble reactor was obtained., This research has been partially supported by Universitat Politecnica de Valencia through project PAID-01-18.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Optimization of the Loading of an Environmentally Friendly Compatibilizer Derived from Linseed Oil in Poly(Lactic Acid)/Diatomaceous Earth Composites

  • Gonzalez, Lucia
  • Agüero, Ángel
  • Quiles-Carrillo, Luis|||0000-0001-8037-2215
  • Lascano-Aimacaña, Diego Sebastián|||0000-0002-0996-1946
  • Montanes, Nestor|||0000-0001-6070-127X
[EN] Maleinized linseed oil (MLO) has been successfully used as biobased compatibilizer in polyester blends. Its effciency as compatibilizer in polymer composites with organic and inorganic fillers, compared to other traditional fillers, has also been proved. The goal of this work is to optimize the amount of MLO on poly(lactic acid)/diatomaceous earth (PLA/DE) composites to open new potential to these materials in the active packaging industry without compromising the environmental effciency of these composites. The amount of DE remains constant at 10 wt% and MLO varies from 1 to 15 phr (weight parts of MLO per 100 g of PLA/DE composite). The e ect of MLO on mechanical, thermal, thermomechanical and morphological properties is described in this work. The obtained results show a clear embrittlement of the uncompatibilized PLA/DE composites, which is progressively reduced by the addition of MLO. MLO shows good miscibility at low concentrations (lower than 5 phr) while above 5 phr, a clear phase separation phenomenon can be detected, with the formation of rounded microvoids and shapes which have a positive e ect on impact strength., This research was funded by the Ministry of Science, Innovation, and Universities (MICIU) project number MAT2017-84909-C2-2-R. L. Quiles-Carrillo is recipient of a FPU grant (FPU15/03812) from the Spanish Ministry of Education, Culture, and Sports (MECD). D. Lascano acknowledges UPV for the grant received though the PAID-01-18 program. N. Montanes acknowledges the project "Development and production of new material from revalued industrial wastes for technological sector applications" for partially funding this research.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Modal decomposition of the unsteady non-reactive flow field in a swirl-stabilized combustor operated by a Lean Premixed injection system

  • Salvador, Francisco Javier|||0000-0003-3269-2251
  • Carreres, Marcos|||0000-0001-6430-6613
  • García-Tíscar, Jorge|||0000-0003-4934-4587
  • Belmar-Gil, M.
[EN] This work is focused on the numerical study of low-order coherent structures of a high-swirled laboratory-scaled combustor operated by a Lean Premixed (LP) injection system in non-reacting conditions through different flow modal decomposition techniques. This will provide valuable insight into the time-spatial modal structure detecting coherent spatial patterns. Experiments suggest the appearance of a self-excited hydrodynamic instability characterized by a single dominant frequency. On the one hand, the dominant pulsating energy components associated with the Precessing Vortex Core (PVC) are identified through the application of a Proper Orthogonal Decomposition (POD) to the instantaneous velocity field. On the other hand, Dynamic Mode Decomposition (DMD) is proven to effectively highlight the relation between the frequency of the most dominant unsteady vortex structures and their spatial distribution within the combustor. Since DMD analysis generates a global frequency spectrum in which each mode corresponds to a specific discrete frequency, its application has been demonstrated to be more efficient than POD when dealing with temporally coherent problems. In this way, the DMD technique has proved to be a robust and systematic method that can give accurate and consistent interpretations of the periodic physics underlying hydrodynamic instabilities in the combustor studied in the present investigation., This work was partly sponsored by the program "Ayuda a Primeros Proyectos de Investigacion (PAID-06-18), Vicerrectorado de Investigacion, Innovacion y Transferencia de la Universitat Politecnica de Valencia (UPV), Spain". We thankfully acknowledge the computer resources at Altamira Supercomputer and the technical support provided by Universidad de Cantabria (RES FI-2018-3-0033 and FI-2019-1-0009) in the frame of the Spanish Supercomputing Network. On the other hand, the support given to Mr. Mario Belmar by Universitat Politecnica de Valencia through the "FPI-Subprograma 2" grant within the "Programa de Apoyo para la Investigacion y Desarrollo (PAID-01-18)" is gratefully acknowledged.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Refractive Index and Temperature Sensing Using Inter-Core Crosstalk in Multicore Fibers

  • Madrigal-Madrigal, Javier|||0000-0003-3156-1321
  • Barrera Vilar, David|||0000-0002-1700-6842
  • Sales Maicas, Salvador|||0000-0001-9457-976X
[EN] Multicore optical fibers are of great interest in the optical sensing field. Their core diversity and spatial distribution enable the development of sensing mechanisms that are not possible in single-core fibers. In this paper, we study the use of the inter-core crosstalk phenomena for the implementation of a surrounding refractive index (SRI) sensor. The selective inscription of a tilted fiber Bragg grating (TFBG) intentionally increases the inter-core crosstalk between the inscribed cores and makes it sensitive to the SRI. With this technique we simplify the measurement of the SRI and improve the identification and tracking of the excited cladding modes, as compared with the analysis of the transmission spectrum of a TFBG in single-core fibers. The proposed device is also sensitive to temperature. Temperature is obtained from the crosstalk wavelength shift with a measured sensitivity of 9.75 pm/degrees C. The SRI is obtained from the measurement of the crosstalk optical power. For increasing SRIs the cladding modes gradually fade, reducing the crosstalk optical power. We observed that the higher the tilt, the higher the sensor sensitivity. For a 7 degrees TFBG the SRI sensitivity obtained is -74.2 dB/RIU from 1.31 to 1.39 and -250.8 dB/RIU from 1.39 to 1.44., This work was supported in part by the Spanish Ministry of Economy and Competitiveness under the DIMENSION TEC2017 88029-R Project and in part by the Generalitat Valenciana by PROMETEO 2017/103 research excellency award and IDI/FEDER/2018 GVA Infraestructura. The work of J. Madrigal was supported by Universitat Politecnica de Valencia scholarship PAID-01-18. The work of D. Barrera was supported by Spanish MICINN fellowship IJCI-2017-32476.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Functionalization of Partially Bio-Based Poly(Ethylene Terephthalate) by Blending with Fully Bio-Based Poly(Amide) 10,10 and a Glycidyl Methacrylate-Based Compatibilizer

  • Jorda, Maria
  • Montava-Jorda, Sergi|||0000-0002-5378-0333
  • Balart, Rafael|||0000-0001-5670-7126
  • Lascano-Aimacaña, Diego Sebastián|||0000-0002-0996-1946
  • Montanes, Nestor|||0000-0001-6070-127X
  • Quiles-Carrillo, Luis|||0000-0001-8037-2215
[Otros] This work shows the potential of binary blends composed of partially bio-based poly(ethyelene terephthalate) (bioPET) and fully bio-based poly(amide) 10,10 (bioPA1010). These blends are manufactured by extrusion and subsequent injection moulding and characterized in terms of mechanical, thermal and thermomechanical properties. To overcome or minimize the immiscibility, a glycidyl methacrylate copolymer, namely poly(styrene-ran-glycidyl methacrylate) (PS-GMA; XibondTM 920) was used. The addition of 30 wt % bioPA provides increased renewable content up to 50 wt %, but the most interesting aspect is that bioPA contributes to improved toughness and other ductile properties such as elongation at yield. The morphology study revealed a typical immiscible droplet-like structure and the effectiveness of the PS-GMA copolymer was assessed by field emission scanning electron microcopy (FESEM) with a clear decrease in the droplet size due to compatibilization. It is possible to conclude that bioPA1010 can positively contribute to reduce the intrinsic sti ness of bioPET and, in addition, it increases the renewable content of the developed materials, This research was funded by the Ministerio de Economía, Industria y Competitividad (MICINN) project number MAT2017-84909-C2-2-R. L. Quiles-Carrillo wants to thank GV for his FPI grant (ACIF/2016/182) and MECD for his FPU grant (FPU15/03812). D. Lascano wants to thank UPV for the grant received though the PAID-01-18 program.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Thermal effects on the diesel injector performance through adiabatic 1D modelling. Part II: Model validation, results of the simulations and discussion

  • Payri, Raul|||0000-0001-7428-5510
  • Salvador, Francisco Javier|||0000-0003-3269-2251
  • Carreres, Marcos|||0000-0001-6430-6613
  • Belmar-Gil, Mario
[EN] In this paper, a one-dimensional computational model of the flow in a common-rail injector is used to compute local variations of fuel temperature (including the temperature change produced upon expansion across the nozzle) and analyse their effect on injector dynamics. These variations are accounted through the adiabatic flow hypothesis, assessed in a first part of the paper where the model features are also described. They imply variations in the fuel properties and the flow regime established across the injector internal restrictions driving the solenoid valve. An extensive validation of the model against experimental results is presented for a wide range of conditions. Multiple injection strategies are also explored, analysing the influence of the inlet fuel temperature and its variations on the mass injected by successive injections and the critical dwell time below which they cannot be separated. Results show significant changes in fuel temperature across some injector restrictions. These changes are greater the higher the rail pressure and lower the fuel temperature at the injector inlet. In the case of the flow across nozzle orifices, the fuel can be either heated or subcooled depending on the operating conditions, the heating being especially relevant for cold-start-like fuel temperatures at the inlet. Thermal effects also influence the injection rate and duration. This influence on injector dynamics is particularly accused in the injector of study due to its ballistic nature. In this regard, the time needed to effectively separate two successive injections is greater the higher the fuel temperature and the injection pressure., This work was partly sponsored by FEDER and the Spanish "Ministerio de Economia y Competitividad" in the frame of the project "Desarrollo de modelos de combustion y emisiones HPC para el analisis de plantas propulsivas de transporte sostenible (CHEST)", reference TRA2017-89139-C2-1-R-AR. On the other hand, the support given to Mr Mario Belmar by "Universitat Politecnica de Valencia" through the "FPI-Subprograma 2" grant within the "Programa de Apoyo para la Investigacion y Desarrollo (PAID-01-18)" is gratefully acknowledged by the authors.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Big Data Transformation in Agriculture: From Precision Agriculture Towards Smart Farming

  • Rodríguez-Sánchez, María De Los Ángeles
  • Cuenca, L.|||0000-0003-3589-4182
  • Ortiz Bas, Ángel|||0000-0001-5690-0807
[EN] Big data is a concept that has changed the way to analyse data and information in different environments such as industry and recently, in agriculture. It is used to describe a large volume of data (structured or unstructured data), which are difficult to obtain, process or parse using conventional technologies and tools like relational databases or conventional statistics, in a reasonable time for their insight. However, Big Data is applied differently in each area to take advantage of its potential and capabilities. Specially in agriculture that presents more demanding conditions due to its inherent uncertainty, so Big Data methods and models from other environments cannot be used straight away in this area. In this paper, we present a review/update of term Big Data and analyse the evolution and the role of Big Data in agriculture outlined the element of collaboration., All authors acknowledge the partial support of Project 691249, RUC-APS: Enhancing and implementing Knowledge based ICT solutions within high Risk and Uncertain Conditions for Agriculture Production Systems, funded by the EU under its funding scheme H2020-MSCA-RISE-2015; and the project "Development of an integrated maturity model for agility, resilience and gender perspective in supply chains (MoMARGE). Application to the agricultural sector." Ref. GV/2017/025 funded by the Generalitat Valenciana. This first author was supported by the Aid Programme of Research and Development of Universitat Politecnica de Valencia [PAID-01-18].
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

M-Bonacci Zone Plates for Ultrasound Focusing

  • Pérez-López, Sergio
  • Fuster Escuder, José Miguel|||0000-0001-7778-8834
  • Candelas Valiente, Pilar|||0000-0002-9924-7673
[EN] In this work, we present a thorough analysis on M-bonacci zone plates for ultrasound focusing applications. These planar lenses are capable of providing bifocal focusing profiles with equal intensity in both foci and become very appealing for a wide range of scenarios including medical and industrial applications. We show that in high-wavelength domains, such as acoustics or microwaves, the separation between both foci can be finely adjusted at the expense of slightly increasing the distortion of the focusing profile, and we introduce a design parameter to deal with this issue and simplify the design process of these lenses. Experimental measurements are in good agreement with numerical simulations and demonstrate the potential of M-bonacci lenses in ultrasound focusing applications., This work has been supported by Spanish MICINN RTI2018-100792-B-I00 project. S.P.-L. acknowledges financial support from Universitat Politecnica de Valencia grant program PAID-01-18.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Mizoroki¿Heck Macrocyclization Reactions at 1 M Concentration Catalyzed by Sub-nanometric Palladium Clusters

  • Garnes-Portoles, Francisco
  • Leyva Perez, Antonio|||0000-0003-1063-5811
  • Merino Marcos, Estibaliz
[EN] The synthesis of cyclized organic compounds with more than ten atoms (macrocycles) is traditionally based on reversible reactions under highly diluted conditions, typically <0.05¿M, in order to circumvent the formation of intermolecular products. These reaction conditions severely hamper industrial productivity and the use of solid catalysts. Herein, it is shown that the intramolecular Mizoroki-Heck reaction of ¿-iodide cinnamates proceeds at 1¿M concentration when catalyzed by few-atom Pd clusters, either in solution or supported on a solid, to give different macrocycles in good yields. This paradigmatic increase in reaction concentration not only opens the door for macrocycle production with high throughputs but also enables the use of solid catalysts for a macrocyclization reaction in flow., This work is part of the project PID2020-115100GB I00 funded by MCIN/AEI/10.13039/501100011033MICIIN (Spain). Financial support by Severo Ochoa center of excellence program (CEX2021-001230-S) and Comunidad de Madrid Research Talent Attraction Program (2018-T1/IND-10054 to E.M.) is gratefully acknowledged. F.G.-P. thanks ITQ, UPV-CSIC for a contract (PAID 01-18).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

A Quickly Deployed and UAS-Based Logistics Network for Delivery of Critical Medical Goods during Healthcare System Stress Periods: A Real Use Case in Valencia (Spain)

  • Quintanilla García, Israel|||0000-0003-0059-5975
  • Jordi Vidal Ull|||0009-0007-0285-8544
  • Vera-Vélez, Norberto
  • Alcaraz Martínez, Pablo
  • Fernández Gallo, Beatríz
[EN] On the one hand, Unmanned Aircraft Systems (UASs) have experienced great applicability surge in the recent years, arising as a promising technology with a wide field of use. On the other hand, healthcare, a critical system in modern society, is subject to a heavy and unexpected pressure in the case of situations such as the COVID-19 pandemic. This article aims to leverage the flexibility of UASs as complementary support for healthcare logistic systems when under high-stress conditions, via quick deployment of an air delivery network. We have defined a logistics network model and created three scenarios based on the model and current needs in Valencia (Spain). Flight tests have been performed in these scenarios, which include urban areas and controlled airspace. Operations complied with requirements derived from the application of Specific Operations Risk Assessment (SORA) methodology, recently adopted by the European Aviation Safety Agency (EASA). Flights were successful, being able to swiftly deliver medical goods without requiring any dedicated infrastructure. However, a moderate number of contingencies took place during the tests, mainly related to control link quality and Air Traffic Management (ATM) integration, forcing the use of dedicated procedures to cope with them. Although additional development is required to ensure the safety of large-scale automated operations, the use of UASs as part of logistic networks is a feasible means to support existing structures, especially in situations in dire need., This research was funded by Generalitat Valenciana (DECRETO 63/2020) and Universitat Politecnica de Valencia (PAID-01-18). The APC was funded by Universitat Politecnica de Valencia.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Influence of key geometrical features on the non-reacting flow of a Lean Direct Injection (LDI) combustor through Large-Eddy Simulation and a Design of Experiments

  • Carreres, Marcos|||0000-0001-6430-6613
  • García-Tíscar, Jorge|||0000-0003-4934-4587
  • Belmar-Gil, Mario
  • Cervelló-Sanz, David
[EN] Lean Direct Injection (LDI) emerged as an interesting concept to limit NOx emissions in aero engines at the cost of operating close to the flame lean blow-off limit. In this technology, fuel is injected into a swirled airstream that generates recirculating flow structures that stabilize the flame. It is then of paramount importance at the design stage to understand the effect of various features on these structures. The present investigation makes use of Eulerian-Lagrangian Large-Eddy Simulations (LES) previously validated against existing experimental data for a reference condition to study the liquid non-reacting flow inside the CORIA Spray LDI burner with the help of Adaptive Mesh Refinement (AMR). A Design of Experiments (DoE) is proposed to analyze the significance of several geometrical features on the flow field, namely the combustor width, the air swirler vane angle, the number of swirler vanes and the axial location of the fuel injector tip. The study covers the qualitative appearance of the flow and the quantitative characterization of the spray dispersion and fuel-air mixing process. In this way, the chosen response variables include the size of the relevant coherent flow structures (Central Toroidal Recirculation Zone induced by the Vortex Breakdown Bubble, Corner Recirculation Zone and Swirled Jet) and their associated velocities, spray features (global drop sizes and spray penetration), pressure drop across the swirler and induced swirl number. Besides, the Precessing Vortex Core (PVC) relevance and frequency content is studied through Proper Orthogonal Decomposition (POD). Results from the statistical analysis show that the number of swirler vanes and their angle are the geometrical parameters that most importantly influence the flow features: stronger recirculation zones leading to an improved atomization and mixing have been found both when decreasing the number of swirler blades and increasing the blade angle. However, both solutions also increase the pressure losses across the swirler. As far as the spectral analysis is concerned, the number of swirler vanes is the most influencing factor on both the frequency and intensity of the PVC modes, being crucial for the possible activation and the energetic content of a double-helix PVC mode., This work was partly sponsored by Grant No. PID2019- 109952RB-I00 Contribución a la aviación sostenible a través de la optimización numérica de cámaras con combustión pobre para aeromotores de nueva generación más silenciosos y limpios (QUILECOM) funded by MCIN/AEI/10.13039/501100011033. The authors thankfully acknowledge the computer resources at Altamira (RES-IM-2020-1-0018) and MareNostrum (RES-IM-2020-2-0009) in the frame of the Spanish Supercomputing Network. Additionally, the support given to Mr. Mario Belmar by Universitat Politècnica de València through the FPI-Subprograma 2 grant within the Programa de Apoyo para la Investigación y Desarrollo (PAID-01-18) is gratefully acknowledged. The authors would also like to thank Prof. Francisco Javier Salvador for the fruitful discussions on the DoE and the selection of Taguchi arrays and Ms. Alicia Muñoz for her help and support modifying the computational domain geometries.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Transient Analysis of Fresnel Zone Plates for Ultrasound Focusing Applications

  • Pérez-López, Sergio
  • Dolmatov, Dimitry O.
  • Tarrazó-Serrano, Daniel|||0000-0001-9986-0884
  • Rubio Michavila, Constanza|||0000-0002-4395-7473
  • Candelas Valiente, Pilar|||0000-0002-9924-7673
[EN] Fresnel Zone Plates are planar lenses that can be used to focus ultrasound beams. This kind of acoustic lenses can play a key role in the resolution of ultrasonic NDT systems. In this type of pulse-echo applications, the pulse duration is an important parameter that specifies the axial resolution, and thus, shorter ultrasound pulses provide higher resolutions. However, acoustic lenses exhibit a transient response that should be considered when setting the pulse duration, as pulses shorter than the transient state duration result in degradation in the response of acoustic lenses in terms of focal intensity, focal displacement, and lateral and axial resolutions. In this work, a thorough analysis of the transient response of Fresnel Zone Plates is discussed, demonstrating that the transient state should be considered in order to achieve optimal focusing performance. Theoretical and numerical results are presented, showing very good agreement., This work has been supported by Spanish MICINN RTI2018-100792-B-I00 project, Generalitat Valenciana AICO/2020/139 and the Russian Governmental program "Science" project FSWW-2020-0014. The research is carried out within the framework of Tomsk Polytechnic University Competitiveness Enhancement Program grant VIU-MNOL NK 187/2020. S.P.-L. acknowledges financial support from Universitat Politècnica de València grant program PAID-01-18. D.T.-S. acknowledges financial support from MICINN BES-2016-07713 project.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

An approach to regionalise the life cycle inventories of Spanish agriculture: Monitoring the environmental impacts of orange and tomato crops

  • Sinisterra-Solis, Nelson Kevin
  • Sanjuán, N.|||0000-0001-9413-0268
  • Ribal, Javier|||0000-0002-9355-0145
  • Estruch-Guitart, Vicente|||0000-0002-7838-8899
  • Clemente Polo, Gabriela|||0000-0003-1173-9903
[EN] Agricultural life cycle assessment (LCA) at the sub-national regional level may be a valuable input for the decision-makers. Obtaining representative and sufficient data to develop life cycle inventories (LCIs) at that level is a relevant challenge. This study aims to contribute to the development of LCIs representative Spanish crops based on economic and operational information available in official sources to assess the average environmental impacts of these crops in the main producing regions. A comprehensive approach is proposed considering both the temporal variability and uncertainty of input data by using different methods (e.g. linear programming, weighted averages, Monte Carlo simulation, forecasted irrigation, etc.) to estimate the inventory data of reference holdings. From these inventories, the environmental assessment of those reference holdings is carried out. Two case studies are developed, on orange and tomato crops in the main producing regions, where climate change (CC), freshwater scarcity (WS), human toxicity non-cancer (HTnc), and freshwater ecotoxicity (ET) are evaluated. The environmental scores obtained differ significantly from region to region. The highest environmental scores of orange reference holdings correspond to Comunidad Valenciana for CC (1.94·10¿1 kg CO2 eq.) HTnc (4.16·10¿11 CTUh) and ET (7.45·10¿3 CTUe), and to Andalucia in WS (17.4 m3 world eq.). As to greenhouse tomatoes, the highest scores correspond to Comunidad Valenciana in the four categories analysed (CC = 3.18 kg CO2 eq., HTnc = 3.6·10¿9 CTUh, ET = 1.5 CTUe and WS = 13.3 m3 world eq.). The environmental scores estimated in this study are consistent with the literature, showing that the approach is useful to obtain a representative description of the environmental profile of crops from official statistical data and other information sources. Widening the data gathered in ECREA-FADN, and also that from other data sources used, would increase the quality of the environmental impact estimation., The authors gratefully acknowledge the Universitat Politècnica de València for providing the funds for N.K. Sinisterra-Solís's research contract through Subprogram 1 (PAID-01-18) and the Colombian Government for funding through COLCIENCIAS. The authors would also like to thank the following people for their support: Diego Gómez and Rafael Laborda for the pesticide treatments of the assessed crops, Juan Manzano for the estimation of irrigation requirements, Assumpció Antón for the estimation of pesticide emissions in greenhouse systems, and Helen Angus for her proofreading of the study.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Experimental study of subwavelength grating bimodal waveguides as ultrasensitive interferometric sensors

  • Torrijos-Morán, Luis
  • Griol Barres, Amadeu
  • García-Rupérez, Jaime|||0000-0002-2036-0084
[EN] Over the recent years, subwavelength grating (SWG) structures have increasingly attracted attention in the area of evanescent-field photonic sensors. In this Letter, for the first time to the best of our knowledge, we demonstrate experimentally the real-time refractive index (RI) sensing using the SWG bimodal interferometric structures. Two different configurations are considered to compare the effect of the nonlinear phase shift, obtained between the two first transverse electromagnetic propagating modes, in the measured bulk sensitivity. Very high experimental values up to 2270 nm/RIU are reached, which perfectly match the numerical simulations and significantly enhance other existing SWG and spectralbased sensors. By measuring the spectral shift, the obtained experimental sensitivity does not depend on the sensor length. As a result, a highly sensitive and compact singlechannel interferometer is experimentally validated for refractive index sensing, thus opening new paths in the field of optical integrated sensors., European Commission (PHC-634013 PHOCNOSIS project); Spanish Government (TEC2015-63838-C3-1-R-OPTONANOSENS project); Universitat Politecnica de Valencia (grant PAID 01-18).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Effect of infill parameters on mechanical properties in additive manufacturing, Efecto de los parámetros del relleno sobre las propiedades mecánicas en fabricación aditiva

  • Ivorra-Martinez, Juan|||0000-0001-8968-4899
  • Quiles-Carrillo, Luis|||0000-0001-8037-2215
  • Lascano-Aimacaña, Diego Sebastián|||0000-0002-0996-1946
  • Ferrándiz Bou, Santiago|||0000-0001-7137-9298
  • Boronat, Teodomiro|||0000-0002-2144-2874
[EN] The purpose of this paper is to study and outline the effects of infill parameters (percentage and pattern) using fused deposition manufacturing on mechanical properties of PLA printed samples. Three infill patterns were tested (rectilinear, honeycomb and Hilbert curve) while infill percentage was tested at three levels (20, 60 and 90 per cent). The properties examined were tensile strength, tensile modulus, elongation, Charpy impact test, morphology of the fractures of tensile and impact test and thermo mechanical analysis. Also, a thermal analysis was done using differential scanning calorimetry to the raw polymer in order to determine the processing temperature. Results showed the influence of the filling parameters in 3D printing on the mechanical properties of the obtained part. The filling pattern greatly influences the mechanical properties of parts with low filling percentages. Honeycomb filling pattern is the one with better mechanical results. The complexity of the filling pattern influences on the processing time. Nozzle direction changes in complex patterns lengthen processing time. Results can significantly influence custom design and manufacturing of parts using material fused deposition modeling., [ES] El propósito de este trabajo es estudiar y esbozar los efectos de los parámetros del relleno (porcentaje y patrón) de la fabricación por deposición fundida sobre las propiedades mecánicas de probetas de PLA. Se han analizado tres patrones de relleno (rectilíneo, panal de abeja y curva Hilbert), y tres porcentajes de relleno distintos (20, 60 y 90 por ciento). Las propiedades examinadas fueron resistencia a la tracción, módulo de tracción, alargamiento, tenacidad utilizando ensayo Charpy, morfología de las fracturas de los ensayos de tracción e impacto y análisis termomecánico. Además, se realizó un análisis térmico utilizando calorimetría diferencial de barrido al polímero virgen para determinar la temperatura de procesamiento. Los resultados mostraron la influencia de los parámetros de llenado en la impresión 3D sobre las propiedades mecánicas de la pieza obtenida. El patrón de llenado influye en gran medida en las propiedades mecánicas de las piezas con bajos porcentajes de relleno. El patrón de relleno de panal de abeja es el que tiene mejores resultados mecánicos de los tres analizados. La geometría del patrón de relleno también influye sobre el tiempo de procesado. Los cambios de dirección de las boquillas en patrones complejos alargan el tiempo de procesamiento. Los resultados obtenidos pueden influir significativamente en el diseño y la fabricación de piezas a medida mediante el modelado de la deposición de material fundido., This work was supported by the POLISABIO program grant number (2019-A02). J. Ivorra-Martinez wants to thank UPV for the grant received through the FPI program, grant (SP20190011). L. Quiles-Carrillo wants to thank MECD for his FPU grant (FPU15/03812). D. Lascano wants to thank UPV for the grant received through the PAID-01-18 program.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Hexagonal Hybrid Bismuthene by Molecular Interface Engineering

  • Dolle, Christian
  • Oestreicher, Víctor
  • Ruiz, Alberto M.
  • Kohring, Malte
  • Wu, Mingjian
  • Sánchez-Santolino, Gabriel
  • Seijas-Da Silva, Alvaro
  • Alcaraz, Marta
  • Eggeler, Yolita M.
  • Spiecker, Erdmann
  • Canet-Ferrer, Josep
  • Weber, Heiko B.
  • Varela, María
  • Garnes-Portoles, Francisco
  • Leyva Perez, Antonio|||0000-0003-1063-5811
[EN] High-quality devices based on layered heterostructuresare typicallybuilt from materials obtained by complex solid-state physical approachesor laborious mechanical exfoliation and transfer. Meanwhile, wet-chemicallysynthesized materials commonly suffer from surface residuals and intrinsicdefects. Here, we synthesize using an unprecedented colloidal photocatalyzed,one-pot redox reaction a few-layers bismuth hybrid of "electronicgrade" structural quality. Intriguingly, the material presentsa sulfur-alkyl-functionalized reconstructed surface that preventsit from oxidation and leads to a tuned electronic structure that resultsfrom the altered arrangement of the surface. The metallic behaviorof the hybrid is supported by ab initio predictionsand room temperature transport measurements of individual nanoflakes.Our findings indicate how surface reconstructions in two-dimensional(2D) systems can promote unexpected properties that can pave the wayto new functionalities and devices. Moreover, this scalable syntheticprocess opens new avenues for applications in plasmonics or electronic(and spintronic) device fabrication. Beyond electronics, this 2D hybridmaterial may be of interest in organic catalysis, biomedicine, orenergy storage and conversion., This work has been supported by the European Union (ERC-2018-StG 804110-2D-PnictoChem & and ERC Proof of Concept Grant 101101079-2D4H2 to G.A.; ERC-2021-StG 101042680 2D-SMARTiES awarded to J.J.B.), the Spanish MICINN (PID2019-111742GA-I00, PID2020-115100GB-I00, MRR/PDC2022-133997-I00, TED2021-131347B-I00, and Excellence Unit Maria de Maeztu CEX2019-000919-M), and the Generalitat Valenciana (CIDEGENT/2018/001, CIDEGENT/2018/005, and CDEIGENT/2019/022). Financial support by Severo Ochoa centre of excellence program (CEX2021-001230-S) is gratefully acknowledged. M.K. and H.B.W. acknowledge support by the Deutsche Forschungsgemeinschaft (DFG), under Projektnummer 182849149 (SFB 953, projects B08 and B13). Electron microscopy work carried out at UCM (M.V., G.S.S.) sponsored by MICINN PID2021-122980OB-C51 and Comunidad de Madrid MAD2D-CM-UCM3. G.S.S. acknowledges financial support from Spanish MCI Grant Nos. RTI2018-099054-J-I00 (MCI/AEI/FEDER, UE) and IJC2018-038164-I. C.D. and Y.M.E. thank the cluster of excellence 3DMM2O funded by DFG under Germany's Excellence Strategy - 2082/1 - 390761711 for financial support. The authors thank Lukas Grunwald and Erich Muller for helpful discussions. A.M.R. thanks the Spanish MIU (Grant No FPU21/04195). A.S.-D. thanks the Universidad de Valencia, for an Atraccion del talento' predoctoral grant. F.G.-P. thanks ITQ, UPV-CSIC for concession of a contract (PAID 01-18).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Pultruded FRP Beams with Embedded Fibre Bragg Grating Optical Sensors for Strain Measurement and Failure Detection

  • Maldonado-Hurtado, Daniel Gustavo|||0000-0001-8585-0271
  • Madrigal-Madrigal, Javier|||0000-0003-3156-1321
  • Sales Maicas, Salvador|||0000-0001-9457-976X
  • Penades, Antonio
  • Ruiz, Rocío
  • Crespo, Ana Isabel
[EN] Composites have added new dimensions to the design and construction of buildings and struc-tures. One of the wider spread composite applications in the construction industry is composite beams or pillars, which can be manufactured through pultrusion processes. These types of con-struction elements are usually used to withstand the weight of large loads, so their integrity must be guaranteed. Due to optical sensors¿ advantages over their electrical counterparts¿small sizes, low weight, non-conductive, and immunity to electromagnetic interference¿and FBGs having an outstanding position among optical fibre sensors¿due to their multiplexation capability and relatively easy monitoring¿in this study, we propose the integration of FBG sensors for the observation and analysis of the integrity of structures made with composite beams over time. The validation test results showed the successful embedding integration of FBG-based fibre optical sensors in an FRP pultrusion beam and strain transmission up to 7500 µ¿ from the composite test piece to the sensor. Additionally, we were able to anticipate the piece failure by the FBG spectrum deformation., This publication is partially supported by the I+D+i project SYNERGY PID2020-118310RBI00 funded by the MCIN/AEI/10.13039/501100011033; also, by the Generalitat Valenciana, the PROMETEO 2017/103 Research Excellency Award, and IDIFEDER/2020/032, as well as IDIFEDER/ 2021/050 GVA Infraestructura. D. Maldonado-Hurtado is supported by a scholarship PRE2018- 085654, funded by MCIN/AEI/10.13039/501100011033, and FSE invierte en tu futuro. J. Madrigal is supported by a scholarship PAID-01-18, funded by Universitat Politècnica de València.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Experimental study of influence of Liquefied Petroleum Gas addition in Hydrotreated Vegetable Oil fuel on ignition delay, flame lift off length and soot emission under diesel-like conditions

  • Pastor, José V.|||0000-0003-4113-4681
  • García Martínez, Antonio|||0000-0001-5783-4936
  • Micó, Carlos|||0000-0001-5787-6212
  • Garcia-Carrero, Alba Andreina
[EN] The fundamental behaviour on ignition and combustion characteristics of blends of Hydrotreated Vegetable Oil and Liquid Petroleum Gas was investigated in a constant high pressure, high temperature combustion chamber, using a prototype lab-scale injection system adapted from a conventional common-rail system to conduct the injection events, ensuring that fuel was liquid at any point of the injection system and avoiding the formation of fuel vapour bubbles that could alter the injected fuel behaviour. The ignition delay, flame lift-off length and the soot formation were studied by means of high-speed imaging techniques, for different operating conditions. The aim of the work is to characterize the effect of Hydrotreated Vegetable Oil-Liquid Petroleum Gas blend ratios on the previously mentioned parameters. Experimental results show that the behaviour of the fuel blends follow the expected trends of conventional diesel type fuels when varying ambient temperature, density and injection pressure. Hydrotreated Vegetable Oil, being the highest reactivity fraction, controls auto ignition of the blend. However, Liquid Petroleum Gas acts as combustion inhibitor increasing both ignition delay and lift-off length as its ratio in the blend increases. As a consequence, the differences observed in terms of flame radiation suggest that increasing Liquid Petroleum Gas fraction reduces soot formation as it promotes a higher air/mixture., The authors acknowledge that this research work has been partly funded by the Government of Spain and FEDER under TRANCO project (TRA2017-87694-R) and by Universitat Politècnica de València through the Programa de Ayudas de Investigación y Desarrollo (PAID01-18) program.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Evaluation of Different Compatibilization Strategies to Improve the Performance of Injection-Molded Green Composite Pieces Made of Polylactide Reinforced with Short Flaxseed Fibers

  • Agüero, Ángel
  • Rojas-Lema, Sandra Paola
  • Garcia-Sanoguera, David|||0000-0002-1923-9519
  • Lascano-Aimacaña, Diego Sebastián|||0000-0002-0996-1946
  • Ivorra-Martinez, Juan|||0000-0001-8968-4899
  • Fenollar, Octavio|||0000-0003-4323-7414
  • Torres-Giner, Sergio|||0000-0001-9071-9542
[EN] Green composites made of polylactide (PLA) and short flaxseed fibers (FFs) at 20 wt % were successfully compounded by twin-screw extrusion (TSE) and subsequently shaped into pieces by injection molding. The linen waste derived FFs were subjected to an alkalization pretreatment to remove impurities, improve the fiber surface quality, and make the fibers more hydrophobic. The alkali-pretreated FFs successfully reinforced PLA, leading to green composite pieces with higher mechanical strength. However, the pieces also showed lower ductility and toughness and the lignocellulosic fibers easily detached during fracture due to the absence or low interfacial adhesion with the biopolyester matrix. Therefore, four different compatibilization strategies were carried out to enhance the fiber-matrix interfacial adhesion. These routes consisted on the silanization of the alkalized FFs with a glycidyl silane, namely (3-glycidyloxypropyl) trimethoxysilane (GPTMS), and the reactive extrusion (REX) with three compatibilizers, namely a multi-functional epoxy-based styrene-acrylic oligomer (ESAO), a random copolymer of poly(styrene-co-glycidyl methacrylate) (PS-co-GMA), and maleinized linseed oil (MLO). The results showed that all the here-tested compatibilizers improved mechanical strength, ductility, and toughness as well as the thermal stability and thermomechanical properties of the green composite pieces. The highest interfacial adhesion was observed in the green composite pieces containing the silanized fibers. Interestingly, PS-co-GMA and, more intensely, ESAO yielded the pieces with the highest mechanical performance due to the higher reactivity of these additives with both composite components and their chain-extension action, whereas MLO led to the most ductile pieces due to its secondary role as plasticizer for PLA., This research work was funded by the Spanish Ministry of Science and Innovation (MICI) project numbers RTI2018-097249-B-C21 and MAT2017-84909-C2-2-R. D.L. and J.I.-M. thanks UPV for the grant received through the PAID-01-18 and PAID-01-19 (SP2019001) programs, respectively. S.T.-G. is recipient of a Juan de la Cierva contract (IJCI-2016-29675) from MICIU while S.R.J. is funded through the Santiago Gisolía contract (GRISOLIAP/2019/132) from Generalitat Valenciana (GVA). The microscopy services of UPV are also acknowledged for their help in collecting and analyzing the FESEM images.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Kinetic Analysis of the Curing Process of Biobased Epoxy Resin from Epoxidized Linseed Oil by Dynamic Differential Scanning Calorimetry

  • Lascano-Aimacaña, Diego Sebastián|||0000-0002-0996-1946
  • Fombuena, Vicent|||0000-0001-7266-6205
  • Balart, Rafael|||0000-0001-5670-7126
  • Montanes, Nestor|||0000-0001-6070-127X
  • Quiles-Carrillo, Luis|||0000-0001-8037-2215
  • Lerma-Canto, Alejandro
[EN] The curing process of epoxy resin based on epoxidized linseed oil (ELO) is studied using dynamic differential scanning calorimetry (DSC) in order to determine the kinetic triplet (E-a, f(alpha) and A) at different heating rates. The apparent activation energy, E-a, has been calculated by several differential and integral isoconversional methods, namely Kissinger, Friedman, Flynn-Wall-Ozawa (FWO), Kissinger-Akahira-Sunose (KAS) and Starink. All methods provide similar values of E-a (between 66 and 69 kJ/mol), and this shows independence versus the heating rate used. The epoxy resins crosslinking is characterized by a multi-step process. However, for the sake of the simplicity and to facilitate the understanding of the influence of the oxirane location on the curing kinetic, this can be assimilated to a single-step process. The reaction model has a high proportion of autocatalytic process, fulfilling that alpha(M) is between 0 and alpha(p) and alpha(M) < alpha(infinity)(p). Using as reference the model proposed by Sestak-Berggren, by obtaining two parameters (n and m) it is possible to obtain, on the one hand, the kinetic parameters and, on the other hand, a graphical comparison of the degree of conversion, alpha, versus temperature (T) at different heating rates with the average n and m values of this model. The good accuracy of the proposed model with regard to the actual values obtained by DSC gives consistency to the obtained parameters, thus suggesting the crosslinking of the ELO-based epoxy has apparent activation energies similar to other petroleum-derived epoxy resins., D.L. thanks UPV for the grant received through the PAID-01-18 program.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Spectral analysis and modelling of the spray liquid injection in a Lean Direct Injection (LDI) gas turbine combustor through Eulerian-Lagrangian Large Eddy Simulations

  • Broatch, A.|||0000-0001-9991-1039
  • Carreres, Marcos|||0000-0001-6430-6613
  • García-Tíscar, Jorge|||0000-0003-4934-4587
  • Belmar-Gil, M.
[EN] The main challenge of next-generation aeronautical gas turbine engines lies in the increase of the efficiency of the cycle and the reduction of pollutant emissions below stringent restrictions. This has led to the design of new injection-combustion strategies working on more risky and problematic operating points such as those close to the lean extinction limit. In This context, the Lean Direct Injection (LDI) concept has emerged as a promising technology to reduce NOx for future aircraft power plants. The study of liquid fuel injection, atomization, evaporation and later interaction with air by means of a numerical approach is deemed to provide a detailed description of these phenomena affecting the overall engine cycle efficiency and emissions. In this context, the aim of this research is to use Large Eddy Simulation for the characterisation of the structure of a liquid non-reacting spray immersed in a strong swirling field in the CORIA Spray LDI burner. An Eulerian formulation is considered for the continuous phase and is coupled with a Lagrangian description for the dispersed phase. A precise description of the fuel droplet size distribution and size-classified velocity, as well as the characterisation of the instantaneous, mean and fluctuating air velocities is presented and compared to the available experimental data. The fuel spray model is shown to accurately reproduce the computed Sauter Mean Diameter (SMD) and the velocity of the droplets. Moreover, the main flow structures generated within the combustor (e.g., Precessing Vortex Core, Vortex Breakdown Bubble, recirculation zones, etc.), which play a crucial role in the fuel-air mixing process, are quantitatively characterised through advanced frequency analysis such as Proper Orthogonal Decomposition (POD) and Dynamic Mode Decomposition (DMD). The characteristic swirling frequency of a single-branched PVC presenting two different phase-shifted POD modes with the same associated spectrum is detected. Finally, POD and DMD techniques are also applied to the numerical spray data to further investigate the spray-turbulence interactions inside the combustion chamber. In ths regard, DMD analysis has confirmed how the swirl-acoustic interactions led in the VBB and PVC oscillations play a crucial role in the way the fuel spray is internally forced by the PVC wavemaker travelling downstream the swirler and synchronised with its dominant frequency. This will contribute to a better understanding of the mixing quality and local equivalence ratios before the subsequent ignition process., This work was partly sponsored by the Spanish Agencia Es-tatal de Investigacion in the frame of the project "Contribucion a la aviacion sostenible a traves de la optimizacion numerica de camaras con combustion pobre para aeromotores de nueva generacion mas silenciosos y limpios (QUILECOM) ", reference PID2019-109952RB-I00. We thankfully acknowledge the computer resources at Marenostrum Supercomputer and the technical sup-port provided by Barcelona Supercomputing Center (RES IM-2019-2-0024 and IM-2019-3-0018) in the frame of the Spanish Super-computing Network. Additionally, the support given to Mr. Mario Belmar by Universitat Politecnica de Valencia through the "FPI-Subprograma 2" grant within the "Programa de Apoyo para la In-vestigacion y Desarrollo (PAID-01-18) " is gratefully acknowledged. The authors would also like to thank Mr. David Cervello and Ms. Alicia Munoz for their technical help and support.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Study of the Influence of the Reprocessing Cycles on the Final Properties of Polylactide Pieces Obtained by Injection Molding

  • Agüero, Ángel
  • Morcillo, Maria del Carmen
  • Quiles-Carrillo, Luis|||0000-0001-8037-2215
  • Balart, Rafael|||0000-0001-5670-7126
  • Boronat, Teodomiro|||0000-0002-2144-2874
  • Lascano-Aimacaña, Diego Sebastián|||0000-0002-0996-1946
  • Torres-Giner, Sergio|||0000-0001-9071-9542
  • Fenollar, Octavio|||0000-0003-4323-7414
[EN] This research work aims to study the influence of the reprocessing cycles on the mechanical, thermal, and thermomechanical properties of polylactide (PLA). To this end, PLA was subjected to as many as six extrusion cycles and the resultant pellets were shaped into pieces by injection molding. Mechanical characterization revealed that the PLA pieces presented relatively similar properties up to the third reprocessing cycle, whereas further cycles induced an intense reduction in ductility and toughness. The effect of the reprocessing cycles was also studied by the changes in the melt fluidity, which showed a significant increase after four reprocessing cycles. An increase in the bio-polyester chain mobility was also attained with the number of the reprocessing cycles that subsequently favored an increase in crystallinity of PLA. A visual inspection indicated that PLA developed certain yellowing and the pieces also became less transparent with the increasing number of reprocessing cycles. Therefore, the obtained results showed that PLA suffers a slight degradation after one or two reprocessing cycles whereas performance impairment becomes more evident above the fourth reprocessing cycle. This finding suggests that the mechanical recycling of PLA for up to three cycles of extrusion and subsequent injection molding is technically feasible., This research was funded by the Spanish Ministry of Science, Innovation, and Universities (MICIU) project numbers MAT2017-84909-C2-2-R and AGL2015-63855-C2-1-R. L. Quiles-Carrillo wants to thank GV for his FPI grant (ACIF/2016/182) and MECD for his FPU grant (FPU15/03812). D. Lascano wants to thank UPV for the grant received through the PAID-01-18 program. S. Torres-Giner is recipient of a Juan de la Cierva¿ Incorporación contract (IJCI-2016-29675) from MICIU. Microscopy services at UPV are acknowledged for their help in collecting and analyzing FESEM images.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Regenerated Fiber Bragg Gratings in Multicore Fiber for Multi-parameter Sensing

  • Madrigal-Madrigal, Javier|||0000-0003-3156-1321
  • Barrera Vilar, David|||0000-0002-1700-6842
  • Sales Maicas, Salvador|||0000-0001-9457-976X
[EN] Multiple regenerated fiber Bragg gratings were inscribed in all the cores of a seven-core fiber in order to develop a multi-parameter sensor designed to operate at high temperatures. We experimentally showed the possibility of measuring strains of up to 1200 mu epsilon, curvatures from 0 degrees to 360 degrees and temperatures up to 1000 degrees C, with a maximum curvature magnitude of at least 4.6 m(-1) and a maximum sensibility of 96 pm/m(-1)., This work was supported in part by the Spanish Ministry of Economy and Competitiveness under the DIMENSION TEC2017 88029-R Project and in part by the Generalitat Valenciana by the PROMETEO 2017/103 Research Excellency Award and IDI/FEDER/2018 GVA Infraestructura. The work of J. Madrigal was supported by a Universitat Politecnica de Valencia scholarship PAID-01-18. The work of D. Barrera was supported by a Spanish MICINN Fellowship IJCI-2017-32476.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Manufacturing and Characterization of Hybrid Composites with Basalt and Flax Fabrics and a Partially Bio-based Epoxy Resin

  • Lascano-Aimacaña, Diego Sebastián|||0000-0002-0996-1946
  • Balart, Rafael|||0000-0001-5670-7126
  • Garcia-Sanoguera, David|||0000-0002-1923-9519
  • Boronat, Teodomiro|||0000-0002-2144-2874
  • Montanes, Nestor|||0000-0001-6070-127X
  • Agüero-Rodríguez, Ángel
[EN] This research is focused on manufacturing and characterization of hybrid composite laminates obtained different stacking sequences of basalt and flax fabrics with silane treatments embedded in a partially bio-sourced epoxy resin as matrix. They were manufactured by the vacuum-assisted resin infusion molding and mechanical properties were tested in tensile, flexural and impact conditions. The effect of the coupling agent on the fiber/matrix interface was studied by FESEM. The effect of temperature on mechanical properties was evaluated by DMTA and TMA. FESEM images revealed improved fiber/matrix interactions with silane treatment, having a more satisfactory effect on basalt fibers than on flax fibers because of its silica-based structure, leading to improved mechanical properties. It is worthy to note that the hybrid stacking sequence has no remarkable influence on the elongation at break. On the contrary, the hybrid stacking sequence offered a great influence on both the elastic modulus and the tensile strength., This research was funded by the Ministerio de Economía, Industria y Competitividad (MICINN) project number MAT2017-84909-C2-2-R. D. Lascano wants to thank UPV for the grant received though the PAID-01-18 program. Microscopy services at UPV are acknowledged for their help in collecting and analyzing FESEM images.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Optimization of the Curing and Post-Curing Conditions for the Manufacturing of Partially Bio-Based Epoxy Resins with Improved Toughness

  • Lascano-Aimacaña, Diego Sebastián|||0000-0002-0996-1946
  • Quiles-Carrillo, Luis|||0000-0001-8037-2215
  • Torres-Giner, Sergio|||0000-0001-9071-9542
  • Boronat, Teodomiro|||0000-0002-2144-2874
  • Montanes, Nestor|||0000-0001-6070-127X
[EN] This research deals with the influence of different curing and post-curing temperatures on the mechanical and thermomechanical properties as well as the gel time of an epoxy resin prepared by the reaction of diglycidyl ether of bisphenol A (DGEBA) with an amine hardener and a reactive diluent derived from plants at 31 wt %. The highest performance was obtained for the resins cured at moderate-to-high temperatures, that is, 80 degrees C and 90 degrees C, which additionally showed a significant reduction in the gel time. This effect was ascribed to the formation of a stronger polymer network by an extended cross-linking process of the polymer chains during the resin manufacturing. Furthermore, post-curing at either 125 degrees C or 150 degrees C yielded thermosets with higher mechanical strength and, more interestingly, improved toughness, particularly for the samples previously cured at moderate temperatures. In particular, the partially bio-based epoxy resin cured at 80 degrees C and post-cured at 150 degrees C for 1 h and 30 min, respectively, showed the most balanced performance due to the formation of a more homogeneous cross-linked structure., This research was supported by the Spanish Ministry of Science, Innovation, and Universities (MICIU) through the MAT2017-84909-C2-2-R program number. D.L. acknowledges Universitat Politècnica de València (UPV) for the grant received through the PAID-01-18 program. L.Q.-C. wants to thank the Generalitat Valenciana (GVA) for his FPI grant (ACIF/2016/182) and the Spanish Ministry of Education, Culture, and Sports (MECD) for his FPU grant (FPU15/03812). S.T.-G. is a recipient of a Juan de la Cierva¿Incorporación contract (IJCI-2016-29675) from MICIU.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Developing a composite indicator to assess agricultural sustainability: Influence of some critical choices

  • Sinisterra-Solis, Nelson Kevin
  • Sanjuán, N.|||0000-0001-9413-0268
  • Ribal, Javier|||0000-0002-9355-0145
  • Estruch-Guitart, Vicente|||0000-0002-7838-8899
  • Clemente Polo, Gabriela|||0000-0003-1173-9903
  • Rozakis, Stelios
[EN] Assessing the sustainability of agriculture is a relevant methodological issue with practical implications. In this study, a systematic approach is followed to develop a composite indicator that ranks the sustainability performance of Spanish reference farms at the NUTS 2 level. The classical three-dimension approach is considered under a deductive point of view to represent sustainability. Multicriteria techniques suitable to model the tradeoffs between individual attributes are used to weigh and aggregate the three dimensions' attributes, allowing for different normative standpoints to be expressed. The sensitivity and uncertainty arising from the methodological choices are assessed using a variance-based technique. The ordinary least squares technique is applied to evaluate the sensitivity of the composite indicator to shifts in the consumption of relevant inputs. The results show that the trade-off level does not leverage most analysed units. In addition, the ranking obtained made it possible to discriminate the herbaceous farms as those with the worst sustainability performance. Methodologically, the most influential parameters in the indicator are related to the ethical complexity of evaluating overall sustainability. In addition, the indicator shows a high sensitivity to shifts in the consumption of machinery fuel and irrigation resources. In short, the indicator developed represents a relevant input to improve the interpretation of the sustainability performance of agriculture as a multidimensional issue, emphasising its normative character., The authors gratefully acknowledge the Universitat Politecnica de Valencia for providing the funds for Sinisterra-Solis's research through Subprogram 1 (PAID-01-18), ADSIDEO - COOPERACION 2020 Program [AD2011], and by the funds provided for a research stay during three months at the Bioeconomy and Biosystems Economics Laboratory of the Technical University of Crete (Chania, Greece). To Erasmus+programme of the European Union that supported the student mobility for traineeships. To the Colombian Government for funding Sinisterra-Solis's research through COLCIENCIAS. The authors would also like to thank Jose David Prieto Campo and Gentil Andres Collazos-Escobar for their statistics support, specifically in multivariate and back to detail steps.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Opto-Mechanical Interactions in Multi-Core Optical Fibers and Their Applications

  • Diamandi, Hilel Hagai
  • London, Yosef
  • Bergman, Arik
  • Bashan, Gil
  • Zadok, Avi
  • Madrigal-Madrigal, Javier|||0000-0003-3156-1321
  • Barrera Vilar, David|||0000-0002-1700-6842
  • Sales Maicas, Salvador|||0000-0001-9457-976X
[EN] Optical fibers containing multiple cores are being developed towards capacity enhancement in space-division multiplexed optical communication networks. In many cases, the fibers are designed for negligible direct coupling of optical power among the cores. The cores remain, however, embedded in a single, mechanically-unified cladding. Elastic (or acoustic) modes supported by the fiber cladding geometry are in overlap with multiple cores. Acoustic waves may be stimulated by light in any core through electrostriction. Once excited, the acoustic waves may induce photo-elastic perturbations to optical waves in other cores as well. Such opto-mechanical coupling gives rise to inter-core cross-phase modulation effects, even when direct optical crosstalk is very weak. The cross-phase modulation spectrum reaches hundreds of megahertz frequencies. It may consist of discrete and narrow peaks, or may become quasi-continuous, depending on the geometric layout. The magnitude of the effect at the resonance frequencies is comparable with that of intra-core cross-phase modulation due to Kerr nonlinearity. Two potential applications are demonstrated: single-frequency opto-electronic oscillators that do not require radio-frequency electrical filters, and point-sensing of liquids outside the cladding of multi-core fibers, where light cannot reach., This work was supported in part by a Starter Grant from the European Research Council (ERC) under Grant H2020-ERC-2015-STG 679228 (L-SID), in part by the Israeli Ministry of Science and Technology under Grant 61047, and in part by the Spanish Ministry of Economy and Competitiveness under the DIMENSION TEC2017 88029-R Project. H. H. Diamandi was supported by the Azrieli Foundation for the award of an Azrieli Fellowship. The work of J. Madrigal was supported by Universitat Politecnica de Valencia scholarship PAID-01-18. The work of D. Barrera was supported by Spanish MICINN fellowship IJCI-2017-32476.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Experimental Study of the Influence of Gasoline-Diesel Blends on the Combustion Process and Soot Formation under Diesel Engine-Like Conditions

  • Pastor, José V.|||0000-0003-4113-4681
  • García Martínez, Antonio|||0000-0001-5783-4936
  • Micó, Carlos|||0000-0001-5787-6212
  • Garcia-Carrero, Alba Andreina
[EN] Recent research has demonstrated that a reduction in pollutant emissions of diesel engines can be achieved by using high octane fuels such as gasoline, methane, or liquefied petroleum gas. Therefore, in this study, the focus was to investigate the influence of blends of diesel and gasoline on combustion characteristics such as ignition delay, rate of heat release, and lift-off length as well as the influence on soot formation. The experiments were carried out in a test rig with optical access which mimics a single-cylinder diesel engine. Four blends were tested: one blend with 100% diesel and then three diesel-gasoline blends with 30%, 50%, and70% gasoline. The blends were made in volumetric proportions and injected using a common rail injection system without any kind of modification. The ignition delay and the apparent heat release were obtained by means of the in-cylinder pressure signal. Furthermore, the combustion development and soot formation were studied using three optical techniques: OH* chemiluminescence, natural luminosity, and diffused back-illumination extinction imaging (DBI). Different engine operating conditions were analyzed. Results showed that ID increases with the gasoline content in the blend. Similarly, as the reacting time increased, the lift-off length was longer. On the other hand, the apparent rate of heat release decreased due to a reduction of the fuel injection rate, which depends on the density of the blend. In addition, differences in the flame radiation were also observed. Gasoline-diesel blends had less luminosity, which is related to less soot formation. To confirm this, the KL factor obtained from the DBI technique was determined, and it was concluded that increasing the gasoline fraction in the blend reduces soot formation., This research work has been partly funded by the Government of Spain and FEDER under TRANCO project (TRA2017-87694-R) and by Universitat Politecnica de Valencia through the Programa de Ayudas de Investigacion y Desarrollo (PAID-01-18 and PAID-06-18) program.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Improved Performance of Environmentally Friendly Blends of Biobased Polyethylene and Kraft Lignin Compatibilized by Reactive Extrusion with Dicumyl Peroxide

  • Rojas-Lema, Sandra Paola
  • Ivorra-Martinez, Juan|||0000-0001-8968-4899
  • Lascano-Aimacaña, Diego Sebastián|||0000-0002-0996-1946
  • Garcia-Garcia, Daniel|||0000-0002-2520-0186
  • Balart, Rafael|||0000-0001-5670-7126
[EN] In this work, different contents (0.25, 0.50, 0.75, and 1 phr) of dicumyl peroxide (DCP) are incorporated into the bio-based high-density polyethylene (bioPE)/kraft lignin (KL) blends with a composition of 80 and 20 wt%, respectively with the aim of improving overall performance. The samples are obtained by reactive extrusion and injection-molding process, and then their overall performance is assessed by tensile tests, thermal analysis, optical and surface appearance, and wettability studies. The obtained mechanical properties confirm the successful interaction between bioPE and KL due to the addition of organic peroxide, which plays a key role in compatibilization. In particular, bioPE/KL blends with 1 phr of DCP achieve an increase in elongation at break of about 300% together with a noticeable increase in the impact strength of about 29% higher than the uncompatibilized bioPE/KL blend, while the tensile modulus decreases 42%. In addition, images obtained by field emission scanning electron microscopy show that the presence of DCP in the blends enhances better dispersion of KL into the bioPE matrix. The wettability analysis indicates that KL and DCP affect the hydrophobicity of the neat bioPE. Therefore, the resultant blends can be considered as potential sustainable polymers with balanced properties., S.R.-L. is a recipient of a Santiago Grisolía grant from Generalitat Valenciana (GVA) (GRISOLIAP/2019/132). D.L. thanks Universitat Politècnica de València (UPV) for the grant received through the PAID-01-18 program. J.I.-M. thanks the Spanish Ministry of Science, Innovation and Universities for his FPU grant (FPU19/01759). Microscopy services at UPV are acknowledged for their help in using and collecting FESEM images.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Dataset to monitor regionalised environmental impacts of the main agricultural products in Spain

  • Sinisterra-Solis, Nelson Kevin
  • Sanjuán, N.|||0000-0001-9413-0268
  • Ribal, Javier|||0000-0002-9355-0145
  • Estruch-Guitart, Vicente|||0000-0002-7838-8899
  • Clemente Polo, Gabriela|||0000-0003-1173-9903
[EN] Estimating the average environmental impacts of a representative crop in a specific region is a helpful starting point from which to propose improvements in the agricultural sector. However, data collection from official representative sources is complex, and often they require subsequent treatment to be transformed into meaningful inventory data. This article shows a comprehensive dataset for obtaining inventory data and developing an environmental life cycle impact assessment of representative agricultural production corresponding to reference holdings at a regional level (NUTS 2) in Spain. The dataset comprises Excel files with the data compiled from secondary sources to be used in the assessment and the R code scripts to transform the data into relevant inventory data to estimate the environmental impacts of the reference holdings. This dataset is a reliable tool for researchers and other potential users to be used as a secondary information source for further studies. It can also be used to estimate the environmental impacts of the farming activity of agri-food products in other regions or countries by collecting similar data for the specific region and adjusting the R code., The authors gratefully acknowledge both the Universitat Politecnica de Valencia for providing the funds for N.K. Sinisterra-Solis's research contract through Subprogram 1 (PAID-01-18) and also the Colombian Government for their funding through COLCIENCIAS.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Coupled-core fiber Bragg gratings for low-cost sensing

  • Flores-Bravo, Jose A.
  • Zubia, Joseba
  • Villatoro, Joel
  • Madrigal-Madrigal, Javier|||0000-0003-3156-1321
  • Sales Maicas, Salvador|||0000-0001-9457-976X
[EN] Sensors based on Bragg gratings inscribed in conventional single mode fibers are expensive due to the need of a sophisticated, but low-speed, interrogation system. As an alternative to overcome this issue, in this work, it is proposed and demonstrated the use of coupled-core optical fiber Bragg gratings. It was found that the relative reflectivity from such gratings changed when the coupled-core fiber was subjected to point or periodic bending. This feature makes the interrogation of such gratings simple, fast, and cost-effective. The reflectivity changes of the gratings are attributed to the properties of the supermodes supported by the coupled-core fiber. As potential applications of the referred gratings, intensity-modulated vector bending and vibration sensing are demonstrated. We believe that the results reported here can pave the way to the development of many inexpensive sensors. Besides, coupled-core fiber Bragg gratings may expand the use of grating technology in other areas., This work is part of the Projects No. PGC2018-101997-B-I00 and RTI2018-094669-B-C31 funded by the MCIN/AEI/10.13039/501100011033/and FEDER, Una manera de hacer Europa; and the scholarship PAID-01-18 Granted by the Universitat Politecnica de Valencia.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Early life stages of the invasive Atlantic blue crab Callinectes sapidus in the Western Mediterranean Sea

  • Gil-Fernández, A.
  • Prado, P.
  • Rodilla, M|||0000-0001-6767-5676
  • Falco, S.|||0000-0002-8679-9153
[EN] The early life cycle of the Atlantic blue crab Callinectes sapidus includes seven zoeal stages that develop in coastal waters, and a later megalopal stage that colonizes estuaries. Although these stages have been largely studied in native ecosystems, very little is known about larval patterns in smaller-scale, invaded, estuarine environments such as those available in the Mediterranean Sea. The general aim of this study is to assess the distribution and abundance of early life stages of C. sapidus in the communication channels of the Albufera lagoon with the Mediterranean Sea, and in adjacent coastal waters. Different sampling methods were employed to target each life stage. (1) For zoeae, planktonic tows were conducted using a 300 ¿ m manta net along 200 m transects parallel to the coastline at distances of 300, 1000 and 3000 m from the shore. (2) A small and manageable passive collector model was used to capture megalopae and juveniles in estuarine areas. This system was first tested from 2020 to 2021 in a single channel, with a weekly sampling frequency, and two more channels were added in 2022. Additionally, intensive daily sampling was conducted in one of the channels from September to November 2022 during the settlement peak. Results showed that zoeae of C. sapidus were more abundant in August 2021, at 1000 m from the coast, and appear to have a disjoint temporal distribution with zoeae of other crab species. Megalopae and juveniles were more abundant from September to November at all sampling sites and times. In 2022, col- lectors featured a dominance of megalopae at two of the sites (ca. 73%), while the site with the lowest salinity showed a dominance of juveniles (84%). For megalopae, comparative results from the intensive and the regular sampling campaigns showed that time of residence within collectors is just a single day. For juveniles, higher numbers were detected with increased deployment time, suggesting a need for enhanced habitat complexity., We want to thank Professor Christoph D. Schubart for his support and training in molecular analysis to A. Gil-Fernandez, whose recent passing has left a big hole in the crab world. May his soul rest in peace.This project was funded by the Ministry of Science and Innovation (Grant PID 2020-118476RR-C21 by MCIN/AEI/10.13039/501100011033) and by the Universitat Politecnica de Valencia (PAID-01 -18, CRUE) , to which we are very thankful.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Manufacturing and Characterization of Green Composites with Partially Biobased Epoxy Resin and Flaxseed Flour Wastes

  • Lascano-Aimacaña, Diego Sebastián|||0000-0002-0996-1946
  • Garcia-Garcia, Daniel|||0000-0002-2520-0186
  • Quiles-Carrillo, Luis|||0000-0001-8037-2215
  • Balart, Rafael|||0000-0001-5670-7126
  • Boronat, Teodomiro|||0000-0002-2144-2874
  • Rojas-Lema, Sandra Paola
[EN] In the present work, green¿composites from a partially biobased epoxy resin (BioEP) reinforced with lignocellulosic particles, obtained from flax industry by¿products or wastes, have been manufactured by casting. In this study, the flaxseed has been crushed by two different mechanical milling processes to achieve different particle sizes, namely coarse size (CFF), and fine size (FFF) particle flaxseed flour, with a particle size ranging between 100¿220 ¿m and 40¿140 ¿m respectively. Subsequently, different loadings of each particle size (10, 20, 30, and 40 wt%) were mixed with the BioEP resin and poured into a mold and subjected to a curing cycle to obtain solid samples for mechanical, thermal, water absorption, and morphological characterization. The main aim of this research was to study the effect of the particle size and its content on the overall properties of composites with BioEP. The results show that the best mechanical properties were obtained for composites with a low reinforcement content (10 wt%) and with the finest particle size (FFF) due to a better dispersion into the matrix, and a better polymer¿particle interaction too. This also resulted in a lower water absorption capacity due to the presence of fewer voids in the developed composites. Therefore, this study shows the feasibility of using flax wastes from the seeds as a filler in highly environmentally friendly composites with a wood¿like appearance with potential use in furniture or automotive sectors., This research was funded by Spanish Ministry of Science, Innovation, and Universities (MICIU), project numbers MAT2017-84909-C2-2-R. This work was supported by the POLISABIO program grant number (2019-A02). D. Lascano thanks Universitat Politècnica de València (UPV) for the grant received through the PAID-01-18 program. D. Garcia-Garcia wants to thank Generalitat Valenciana (GVA) for their financial support through a post-doctoral grant (APOSTD/2019/201). S. Rojas-Lema is a recipient of a Santiago Grisolía contract (GRISOLIAP/2019/132) from GVA. L. Quiles-Carrillo wants to thank GV for his FPI grant (ACIF/2016/182) and MECD for his FPU grant (FPU15/03812). Microscopy services at UPV are acknowledged for their help in collecting and analyzing FESEM images.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Multicore optical fiber shape sensors suitable for use under gamma radiation

  • Barrera Vilar, David|||0000-0002-1700-6842
  • Madrigal-Madrigal, Javier|||0000-0003-3156-1321
  • Sales Maicas, Salvador|||0000-0001-9457-976X
  • Delepine-Lesoille, Sylvie
[EN] We have designed and implemented a fiber optic shape sensor for high-energy ionizing environments based on multicore optical fibers. We inscribed two fiber Bragg gratings arrays in a seven-core optical fiber. One of the arrays has been inscribed in a hydrogen-loaded fiber and the other one in an unloaded fiber in order to have two samples with very different radiation sensitivity. The two samples were coiled in a metallic circular structure and were exposed to gamma radiation. We have analyzed the permanent radiation effects. The radiation-induced Bragg wavelength shift (RI-BWS) in the hydrogen-loaded fiber is near ten times higher than the one observed for the unloaded fiber, with a maximum wavelength shift of 415 pm. However, the use of the multiple cores permits to make these sensors immune to RI-BWS obtaining a similar curvature error in both samples of approximately 1 cm without modifying the composition of the fiber, pre-irradiation or thermal treatment., Ministerio de Economia y Competitividad (DIMENSION TEC2017 88029- R); Generalitat Valenciana (IDI/FEDER/2018, PROMETEO 2017/103); H2020 Marie Sklodowska-Curie Actions (MSCA-ITN-ETN-722509); Universitat Politecnica de Valencia (PAID-01-18); Ministerio de Ciencia, Innovacion y Universidades (IJCI-2017-32476).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Semiautomatic generation and assessment of Java exercises in engineering education

  • Insa Cabrera, David
  • Pérez-Rubio, Sergio
  • Tamarit Muñoz, Salvador
  • Silva, Josep|||0000-0001-5096-0008
[EN] Continuous assessment is essential in education. It should be an integral part of education that provides immediate feedback to students. Unfortunately, the assessment of programming source code is still a hand-operated and error-prone task, and can take weeks before the student gets feedback. This study presents a semiautomatic code assessment method able to automatically apply black-box assessment (which relies on the comparison of input-output pairs) and white-box assessment (which relies on checking different source code properties). The method proposed is a general-purpose assessment system that was originally designated to be used in engineering education, but that can be used in other educational contexts to assist the assessment of any Java programming assignments or exams. The main advantage of this system is that the assessment made is quicker, exhaustive, and objective; and it does not produce false positives. After the application of this method over two years in several real university courses, we have released a public and free implementation. An empirical evaluation of this system estimates that the amount of assessment work automatically done by the tool is over 48%. Additionally, the system has been used to measure the average subjective influence (i.e., assessment errors) introduced by teachers when they assess exams manually., MINECO/AEI/FEDER (EU), Grant/Award Number: TIN2016-76843-C4-1-R; Universitat Politecnica de Valencia, Grant/Award Number: FPI Grant PAID-01-18; Generalitat Valenciana, Grant/Award Number: Prometeo/2019/098 (DeepTrust); TAILOR, EU Horizon 2020, Grant/Award Number: GA No 952215
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Liquid-liquid core-shell configurable mesoscale spherical acoustic lens with subwavelength focusing

  • Pérez-López, Sergio
  • Minin, Oleg V.
  • Minin, Igor V.
  • Candelas Valiente, Pilar|||0000-0002-9924-7673
  • Fuster Escuder, José Miguel|||0000-0001-7778-8834
  • Rubio Michavila, Constanza|||0000-0002-4395-7473
[EN] In this work, we present a lens based on a thin hollow ABS spherical container structure, which can be filled up with different compatible liquids. The acoustic jet can be dynamically shaped by either shifting the operating frequency or modifying the geometry of the lens. We show for the first time that a spherical Ethanol ABS core¿shell acoustical lens immersed in water with low diameter-to-wavelength ratio equal to 6.67 and refraction index of 1.24 achieves a focusing spot narrower than 0.85¿. Experimental measurements validate simulation results and demonstrate the viability of these configurable spherical lenses in underwater acoustic focusing applications., This work has been supported by Spanish MINECO TEC2015-70939-R and MICINN RTI2018-100792-B-I00 projects. S.P.-L. acknowledges financial support from Universitat Politècnica de València grant program PAID-01-18. I.V.M. and O.V.M. acknowledge the Tomsk Polytechnic University Competitiveness Enhancement Program.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Manufacturing and Characterization of Functionalized Aliphatic Polyester from Poly(lactic acid) with Halloysite Nanotubes

  • Montava-Jorda, Sergi|||0000-0002-5378-0333
  • Lascano-Aimacaña, Diego Sebastián|||0000-0002-0996-1946
  • Sanchez-Nacher, Lourdes|||0000-0002-8627-4576
  • Montanes, Nestor|||0000-0001-6070-127X
  • Chacon, Victor
[EN] This work reports the potential of poly(lactic acid)-PLA composites with different halloysite nanotube (HNTs) loading (3, 6 and 9 wt%) for further uses in advanced applications as HNTs could be used as carriers for active compounds for medicine, packaging and other sectors. This work focuses on the effect of HNTs on mechanical, thermal, thermomechanical and degradation of PLA composites with HNTs. These composites can be manufactured by conventional extrusion-compounding followed by injection molding. The obtained results indicate a slight decrease in tensile and flexural strength as well as in elongation at break, both properties related to material cohesion. On the contrary, the stiffness increases with the HNTs content. The tensile strength and modulus change from 64.6 MPa/2.1 GPa (neat PLA) to 57.7/2.3 GPa MPa for the composite with 9 wt% HNTs. The elongation at break decreases from 6.1% (neat PLA) down to a half for composites with 9 wt% HNTs. Regarding flexural properties, the flexural strength and modulus change from 116.1 MPa and 3.6 GPa respectively for neat PLA to values of 107.6 MPa and 3.9 GPa for the composite with 9 wt% HNTs. HNTs do not affect the glass transition temperature with invariable values of about 64 degrees C, or the melt peak temperature, while they move the cold crystallization process towards lower values, from 112.4 degrees C for neat PLA down to 105.4 degrees C for the composite containing 9 wt% HNTs. The water uptake has been assessed to study the influence of HNTs on the water saturation. HNTs contribute to increased hydrophilicity with a change in the asymptotic water uptake from 0.95% (neat PLA) up to 1.67% (PLA with 9 wt % HNTs) and the effect of HNTs on disintegration in controlled compost soil has been carried out to see the influence of HNTs on this process, which is a slight delay on it. These PLA-HNT composites show good balanced properties and could represent an interesting solution to develop active materials., This research was supported by the Ministry of Science, Innovation, and Universities (MICIU) through the MAT2017-84909-C2-2-R program number. D. Lascano wants to thank UPV for the grant received though the PAID-01-18 program. Microscopy services at UPV are acknowledged for their help in collecting and analyzing FESEM images.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Assessing the environmental impact of Spanish vineyards in Utiel-Requena PDO: The influence of farm management and on-field emission modelling

  • Sinisterra-Solis, Nelson Kevin
  • Sanjuán, N.|||0000-0001-9413-0268
  • Estruch-Guitart, Vicente|||0000-0002-7838-8899
  • Clemente Polo, Gabriela|||0000-0003-1173-9903
[EN] Environmental studies into wine from different protected designations of origin (PDO) highlight farming and packaging stages as those contributing the most to the total environmental impacts of this product. However, farming impact, not only depends on the agricultural practices but also on data quality and modelling complexity. By using the life cycle assessment methodology, a twofold goal is aimed. Firstly, to analyse the environmental profile of the most widespread viticultural practices in the Utiel-Requena PDO (Spain). The second aim is to evaluate the differences between the environmental impacts estimated by means of modelling approaches using generic information (Baseline modelling) versus those using site-specific information (Alternative modelling). As regards the agricultural practices and grape cultivars, eight systems were defined and assessed per kg of grape at the farm gate. The differences between farming systems and modelling approaches were statistically assessed. The results show that, regardless of the grape cultivar, organic systems are more environmentally friendly than the conventional ones (on average, the greatest differences occur in the ionizing radiation, marine eutrophication and land use, being the values for organic vineyards 1678%, 648% and 171% lower than those of the conventional ones, respectively), the results for the Bobal cultivar being better than those for the Tempranillo because of the higher yield (differences in yield around 1.500 kg ha¿1). The use of site-specific modelling approaches guarantees the precision of the analysis; however, for some impact categories, namely climate change, fine particulate matter formation, marine eutrophication and terrestrial acidification, the possibility of using general methodologies is open; in this way, the modelling efforts can be minimised, and the results would be consistent with those of more specific methodologies. The results also underline the need for a consensus within LCA practitioners on which methodologies to use in order to estimate on-field emissions taking into account both complexity reduction and accuracy improvement., The authors gratefully acknowledge the Spanish Ministerio de Economia y Competitividad for the financial support under the project CTM 2013-47,340-R and the Universitat Politecnica de Valencia for providing the funds for N.K. Sinisterra-Solis's research contract through Subprogram 1 (PAID-01-18).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

On the focusing enhancement of Soret zone plates with ultrasound directional transducers

  • Pérez-López, Sergio
  • Fuster Escuder, José Miguel|||0000-0001-7778-8834
  • Candelas Valiente, Pilar|||0000-0002-9924-7673
  • Rubio Michavila, Constanza|||0000-0002-4395-7473
[EN] This work analyzes the influence of the distribution of transparent Fresnel regions over the focusing profile of Soret Zone Plates. It is shown that this effect becomes very significant in those fields where directional transducers are employed, such as microwaves or acoustics. A thorough analysis on both the lens transmission efficiency and the focusing enhancement factor is presented. Moreover, experimental measurements are also carried out, validating the theoretical model and demonstrating that the distribution of transparent Fresnel regions becomes a critical parameter in applications requiring directional emitters., This work was supported by Spanish MINECO TEC2015-70939-R and MICINN RTI2018-100792-B-I00 projects. S.P.-L. acknowledges financial support from Universitat Politecnica de Valencia Grant Program No. PAID-01-18.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Acoustic Focusing Enhancement In Fresnel Zone Plate Lenses

  • Tarrazó-Serrano, Daniel|||0000-0001-9986-0884
  • Candelas Valiente, Pilar|||0000-0002-9924-7673
  • Uris Martínez, Antonio|||0000-0002-2005-2305
  • Rubio Michavila, Constanza|||0000-0002-4395-7473
  • Pérez-López, Sergio
[EN] The development of flat acoustic lenses for different applications such as biomedical engineering is a topic of great interest. Flat lenses like Fresnel Zone Plates (FZPs) are capable of focusing energy beams without the need of concave or convex geometries, which are more difficult to manufacture. One of the possible applications of these type of lenses is tumor ablation through High Intensity Focused Ultrasound (HIFU) therapies with real time Magnetic Resonance Imaging (MRI) monitoring. In order to be MRI compatible, the FZP material cannot have electromagnetic interaction. In this work, a Phase-Reversal FZP (PR-FZP) made of Polylactic Acid (PLA) manufactured with a commercial 3D printer is proposed as a better, more efficient and MRI compatible alternative to conventional Soret FZPs. Phase-Reversal lenses, unlike traditional FZPs, take advantage of all the incident energy by adding phase compensation regions instead of pressure blocking regions. The manufactured PR-FZP achieves 21.9 dB of focal gain, which increases the gain compared to a Soret FZP of its same size by a factor of 4.0 dB. Both numerical and experimental results are presented, demonstrating the improved focusing capabilities of these types of lenses., This work has been supported by Spanish MINECO (TEC2015-70939-R). S.P.-L. acknowledges financial support from Universitat Politècnica de València through grant program PAID-01-18.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Manufacturing and Characterization of High-Density Polyethylene Composites with Active Fillers from Persimmon Peel Flour with Improved Antioxidant Activity and Hydrophobicity

  • Rojas-Lema, Sandra Paola
  • Lascano-Aimacaña, Diego Sebastián|||0000-0002-0996-1946
  • Ivorra-Martinez, Juan|||0000-0001-8968-4899
  • Gómez-Caturla, Jaume|||0000-0001-8680-4509
  • Balart, Rafael|||0000-0001-5670-7126
  • Garcia-Garcia, Daniel|||0000-0002-2520-0186
[EN] The potential of persimmon peel waste (PPF) as renewable active filler in biobased polyethylene composites, with improved antioxidant properties and resistance to water uptake is shown. To improve the interaction between the hydrophilic biofiller and the highly hydrophobic matrix, several compatibilization approaches are assessed. The first approach consists of using a polyethylene grafted copolymer with maleic anhydride (PE-g-MA). The second approach consists of modifying the PPF surface with two treatments before compounding with Bio-HDPE. The first consists on conventional silanization with (3-glycidyloxypropyl)trimethoxysilane, while the second consists on esterification with palmitoyl chloride. The results show an improvement of the matrix/biofiller interaction, as observed by field emission scanning electron microscopy (FESEM), leading to an increase in Young¿s modulus of 10% in composites compatibilized with PE-g-MA, and silanized PPF compared to composites without compatibilizer and no surface treatment on PPF. Interestingly, treatment with palmitoyl chloride leads to an increase in the hydrophobic behavior of composites keeping the water contact angle virtually constant at 128°. This effect is also reflected in a clear decrease in water absorption capacity of only 0.3 wt% over 9 weeks. Finally, PPF increases stabilization against oxidation, improving the oxidation induction time from 4.8 min (Bio-HDPE) to 82.5 min for composites with silanized PPF., The authors want to thank the Spanish Ministry of Science and Innovation, grant number MEN PID2020-116496RB-C22 for funding this research. D.L. wants to thank UPV for the grant received though the PAID-01-18 program. S.R.-L. is a recipient of a Santiago Grisolia grant from Generalitat Valenciana (GVA) (GRISOLIAP/2019/132). J.G.-C. wants to thank Universitat Politècnica de València for his FPI grant from (SP20200080). J.I.-M. thanks the Spanish Ministry of Science, Innovation and Universities for his FPU grant (FPU19/01759). Microscopy services at UPV are acknowledged for their help in collecting and analyzing FESEM images.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Study of the mechanical properties of polylactide composites with jute reinforcements

  • Lascano-Aimacaña, Diego Sebastián|||0000-0002-0996-1946
  • Ivorra-Martinez, Juan|||0000-0001-8968-4899
  • Montanes, Nestor|||0000-0001-6070-127X
  • Cristobal Aljaro
  • Eduardo Fages
  • Sandra Rojas-Lema
[EN] Concern has arisen in recent years over the excessive use of oil-based materials, making the development of new materials with a low environmental impact all the more urgent. In this study, environmentally friendly composites were obtained using a thermoplastic polylactide (PLA) matrix with jute fibers (fabrics and non-woven mats) as reinforcement. PLA/jute biocomposites were manufactured by thermocompression. The effect of the amount of jute fiber reinforcement (in the 30¿50¿wt.% range) on the tensile and flexural properties of these composites was analyzed, and the fiber¿matrix interaction was assessed by scanning electron microscopy. The results show that thermocompression molding is a simple technique for obtaining high-environmental-efficiency biocomposites with high reinforcement loadings (up to 50¿wt.%). As expected, the tensile properties are directly related to the amount of fiber loading, as well as the directionality of these fibers in the composite. Mechanical performance is also highly dependent on fiber¿matrix interactions. These biocomposites could be attractive as lightweight interior panels in the automotive industry, cases/covers in electric/electronic applications, and turbine blade components in the wind energy industry, among others, due to their balanced mechanical properties and the rather complex shapes that could be obtained by thermocompression., This research is part of grant PID2020-116496RB-C22 funded by MCIN/AEI/10.13039/501100011033 and grant AICO/2021/025 funded by Generalitat Valenciana (GVA). S. Rojas-Lema is a recipient of a Santiago Grisolía grant from GVA (GRISOLIAP/2019/ 132). D. Lascano wants to thank Universitat Politècnica de València (UPV) for the grant received through the PAID-01-18 program. J. Ivorra-Martinez wants to thank FPU19/01759 grant funded by MCIN/AEI/10.13039/501100011033 and by ESF Investing in Your Future.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Modeling gaseous non-reactive flow in a lean direct injection gas turbine combustor through an advanced mesh control strategy

  • Payri, Raul|||0000-0001-7428-5510
  • Novella Rosa, Ricardo|||0000-0002-5123-6924
  • Carreres, Marcos|||0000-0001-6430-6613
  • Belmar-Gil, Mario
[EN] Fuel efficiency improvement and harmful emissions reduction are the main motivations for the development of gas turbine combustors. Numerical computational fluid dynamics (CFD) simulations of these devices are usually computationally expensive since they imply a multi-scale problem. In this work, gaseous non-reactive unsteady Reynolds-Averaged Navier-Stokes and large eddy simulations of a gaseous-fueled radial-swirled lean direct injection combustor have been carried out through CONVERGE (TM) CFD code by solving the complete inlet flow path through the swirl vanes and the combustor. The geometry considered is the gaseous configuration of the CORIA lean direct injection combustor, for which detailed measurements are available. The emphasis of the work is placed on the demonstration of the CONVERGE (TM) applicability to the multi-scale gas turbine engines field and the determination of an optimal mesh strategy through several grid control tools (i.e., local refinement, adaptive mesh refinement) allowing the exploitation of its automatic mesh generation against traditional fixed mesh approaches. For this purpose, the normalized mean square error has been adopted to quantify the accuracy of turbulent numerical statistics regarding the agreement with the experimental database. Furthermore, the focus of the work is to study the behavior when coupling several large eddy simulation sub-grid scale models (i.e., Smagorinsky, Dynamic Smagorinsky, and Dynamic Structure) with the adaptive mesh refinement algorithm through the evaluation of its specific performances and predictive capabilities in resolving the spatial-temporal scales and the intrinsically unsteady flow structures generated within the combustor. This investigation on the main non-reacting swirling flow characteristics inside the combustor provides a suitable background for further studies on combustion instability mechanisms., The author(s) disclosed receipt of the following financial support for the research, authorship, and/or publication of this article: This work was partly sponsored by the program "Ayuda a Primeros Proyectos de Investigacion (PAID-06-18), Vicerrectorado de Investigacion, Innovacion y Transferencia de la Universitat Politecnica de Valencia (UPV), Spain.'' The support given to Mr. Mario Belmar by Universitat Politecnica de Valencia through the "FPI-Subprograma 2'' grant within the "Programa de Apoyo para la Investigacion y Desarrollo (PAID-01-18)'' is gratefully acknowledged.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

An experimental study with renewable fuels using ECN Spray A and D nozzles

  • Pastor, José V.|||0000-0003-4113-4681
  • García-Oliver, José M|||0000-0002-2676-9681
  • Micó, Carlos|||0000-0001-5787-6212
  • Garcia-Carrero, Alba Andreina
[EN] The decarbonization process of the automotive industry and the road transport sector has raised the interest on the development of cleaner fuels. A proper characterization of their properties and behavior under different operating conditions is mandatory to achieve an effective implementation in commercial engines. With this objective, the current work presents a comparison of two injectors from the Engine Combustion Network (ECN), namely Spray A and Spray D injectors, in terms of spray characteristics and combustion behavior for different fuels: diesel, dodecane, Hydrotreated Vegetable Oil (HVO), and two types of oxymethylene ethers (OME1 and OME x ). The aim is to analyze how differences in nozzle geometry affect the behavior of different types of fuels. The experiments were carried out in a High Temperature and High Pressure test rig and operating conditions were chosen following ECN guidelines. Visualization techniques such as high speed schlieren imaging, OH* chemiluminescence and diffused back illumination were implemented to analyze the differences in liquid length, vapor penetration, auto ignition, flame lift-off length, and soot formation for both nozzles. In general, results showed the same trend for all the fuels tested: longer liquid length and faster vapor penetration for Spray D, as well as higher ignition delay and longer lift-off length. However, it was found that these parameters were less sensitive to the nozzle diameter for the oxygenated fuels tested. Furthermore, a different trend was observed for OME1, in terms of ignition behavior, in comparison to the other fuels. In terms of soot production, the Spray D nozzle increases its formation with the non-oxygenated fuels. In contrast, no soot was observed with the oxygenated ones under any operating conditions., The author(s) disclosed receipt of the following financial support for the research, authorship, and/or publication of this article: The authors acknowledge that this research work has been partly funded by the European Union's Horizon 2020 Programme, grant agreement no. 828947, and from the Mexican Department of Energy, CONACYT-SENER Hidrocarburos grant agreement no. B-S-69926 and by Universitat Politecnica de Valencia through the Programa de Ayudas de Investigacion y Desarrollo (PAID-01-18). Part of the equipment used in this work was funded by FEDER and GVA through contract IDIFEDER/2018/037.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Program slicing of Java programs

  • Galindo, Carlos|||0000-0002-3569-6218
  • Silva, Josep|||0000-0001-5096-0008
  • Pérez, Sergio
[EN] Program slicing is a technique to extract the part of the program that can affect the values computed at a given program point (known as the slicing criterion). To represent programs, program slicing uses the System Dependence Graph (SDG), for which several extensions like the Java System Dependence Graph (JSysDG) or the Sub-Statement Linear Dependence Graph (SSLDG) exist to deal with Java object-oriented programs. In this paper, we present an incompleteness result proving that these graphs do not produce complete slices in all cases, and specifically when some object variables are selected as the slicing criterion. We first identify the source of the problem: the representation of dependences between partial definitions of objects is ill-defined in these approaches, leading to a loss of completeness in many cases. To solve this limitation, we extend these representations with the addition of a specific flow dependence for object type variables called object-flow dependence. This extension provides a more accurate flow representation between object variables and its data members and it allows us to obtain complete slices when an object variable is selected as the slicing criterion.(c) 2022 The Authors. Published by Elsevier Inc. This is an open access article under the CC BY-NC-ND license (http://creativecommons.org/licenses/by-nc-nd/4.0/)., This work has been partially supported by grant PID2019-104735RB-C41 funded by Spanish MCI/AEI/10.13039/501100011033, by the Generalitat Valenciana under grant Prometeo/2019/098 (DeepTrust), and by TAILOR, a project funded by EU Horizon 2020 research and innovation programme under GA No 952215. Carlos Galindo was partially supported by the Spanish Ministerio de Universidades under grant FPU20/03861. Sergio Perez was partially supported by Universitat Politecnica de Valencia under FPI grant PAID-01-18.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Experimental approach for the analysis of the flow behaviour in the stator of a real centripetal turbine

  • Galindo, José|||0000-0001-6068-182X
  • Tiseira, Andrés-Omar|||0000-0001-9472-2386
  • García-Cuevas González, Luis Miguel|||0000-0001-9340-0617
  • Hervás-Gómez, Natalia
[EN] During normal operation, radial turbines may work in off-design conditions. Off-design conditions may be characterised by very low expansion ratios, very high expansion ratios, very low rotational speeds or very high rotational speeds. All of these cases are difficult to characterise experimentally due to high experimental uncertainties or a lack of capabilities in the system feeding pressurised air to the turbine. Also, there are two- and three-dimensional computational fluid dynamics simulations at these operating points but could not be accurate enough due to high turbulence effects, flow detachment and shock wave generation. With a lack of high-quality data, experimental or computational, to fit the reduced-order turbine models used in zero- and one-dimensional engine simulations, there are large uncertainties associated to their results in off-design conditions. This work develops an experimental facility able to characterise the internal flow of radial turbine stators in terms of pressure and velocity fields at off-design and regular working conditions. The facility consists of an upscaled model of a radial turbine volute and stator fed with air in pressure- and temperature-controlled conditions, so different sensors can be used inside it with the least amount of flow disturbance. The different restrictions considered in the design of the upscaled model are presented, and their effects in the final experimental apparatus capabilities are discussed. A preliminary comparison between computational fluid dynamics simulations and experimental data shows encouraging results., The author(s) disclosed receipt of the following financial support for the research, authorship, and/or publication of this article: This work was partly sponsored by the programme 'Ayuda a Primeros Proyectos de Investigacion (PAID-06-18), Vicerrectorado de Investigacion, Innovacion y Transferencia de la Universitat Politecnica de Valencia (UPV), Spain'. The support given to Ms N.H.G. by Universitat Politecnica de Valencia through the 'FPI-Subprograma 2' (No. FPI-2018-S2-1368) grant within the 'Programa de Apoyo para la Investigacion y Desarrollo (PAID-0118)' is gratefully acknowledged.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Sampled true time delay line operation by inscription of long period gratings in few-mode fibers

  • García-Cortijo, Sergi|||0000-0002-7237-9457
  • Madrigal-Madrigal, Javier|||0000-0003-3156-1321
  • Barrera Vilar, David|||0000-0002-1700-6842
  • Sales Maicas, Salvador|||0000-0001-9457-976X
  • Gasulla Mestre, Ivana|||0000-0001-8088-7796
  • Guillem-Cogollos, Rubén
[EN] We propose and experimentally demonstrate distributed microwave photonics signal processing over a few-mode fiber link by implementing 4-sample true time delay line operation. The inscription of a set of long period gratings at specific locations along the few-mode fiber allows the excitation of the higher-order modes while adjusting the individual sample group delays and amplitudes that are required for sampled true time delay line behavior. Since solely the injection of the fundamental mode at the few-mode fiber input is required, we render this signal processing system independent of any preceding fiber link that may be required in addition to distribute the signal. We experimentally validate the performance of the implemented true time delay line when applied to radiofrequency signal filtering., European Research Council (ERC) (Consolidator Grant 724663); Spanish MINECO (TEC2014-60378-C2-1-R and TEC2016-80150-R projects, BES-2015-073359 scholarship for S. Garcia, IJCI-2017-32476 fellowship for D. Barrera, Ramon y Cajal fellowship RYC-2014-16247 for I. Gasulla); Universitat Politecnica de Valencia (PAID-01-18 scholarship for J. Madrigal).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Macrocyclization Reactions at High Concentration (&gt, =0.2M): The Role of Catalysis

  • Garnes-Portoles, Francisco
  • Leyva Perez, Antonio|||0000-0003-1063-5811
[EN] The synthesis ofmacrocycles is fundamental to obtainuseful quantitiesof this unique family of organic compounds. However, most currentsyntheses still require highly diluted conditions (generally <0.1M), which makes the synthesis extremely inefficient in the reactorvolume. Here we review, quantify, and analyze the few synthetic methodsfor macrocycles reported so far where the reaction solution is at & GE; 0.2 M concentration. Parametrization of the results withthe Emac (efficiency macrocyclization) index unveils that catalyticmethods are much more efficient than non-catalyzed methods. Beyondthis conclusion, the present study also shows clear evidence thathigh-concentration macrocyclization reactions are not only possiblebut necessary, and suggests the use of catalytic reactions, includingsolid catalysts and in-flow reactions, to develop macrocyclizationreactions under high concentration conditions., This work is part of the project PID2020-115100GB-I00 funded by MCIN/AEI/10.13039/501100011033MICIIN (Spain). Financial support by Severo Ochoa centre of excellence program (CEX2021-001230-S) is gratefully acknowledged. F. G.-P. thanks ITQ, UPV-CSIC for concession of a contract (PAID 01-18).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

From farm accountancy data to environmental indicators: Assessing the environmental performance of Spanish agriculture at a regional level

  • Sinisterra-Solis, Nelson Kevin
  • Sanjuán, N.|||0000-0001-9413-0268
  • Ribal, Javier|||0000-0002-9355-0145
  • Estruch-Guitart, Vicente|||0000-0002-7838-8899
  • Clemente Polo, Gabriela|||0000-0003-1173-9903
[EN] Understanding the environmental impacts of current agricultural practices is a starting point for transitioning towards sustainable agriculture, which is a goal to be achieved by the European Union. This study aims to provide a set of environmental impact indicators with which to assess and compare the environmental performance of a broad group of agricultural reference holdings at the Spanish NUTS 2 level. A life cycle assessment approach based on statistical data on farm accountancy is applied. The unit of analysis is a reference holding on which a specific crop is grown in a NUTS 2 and follows a specific management system (open-field irrigated, open-field rainfed, or greenhouse). The system boundaries are set at the farm gate, and the impact results are expressed per 1 euro of net value added. For most reference holdings, the EF scores per net value added are similar regardless of their EF scores per kg commodity, suggesting a correspondence between the use of resources and the economic results. The environmental footprint is clustered into four groups. The first one accounts for 78 % of the sample and represents the holdings with the lowest impact (between 9.7 & BULL;10-5 and 2.88 & BULL;10-3 EF score & BULL;NVAfc-1); the second cluster groups seven reference holdings (3 herbaceous and 4 Mediterranean perennial crops) with an environmental footprint of between 3.04 & BULL;10-3 and 9.01 & BULL;10-3 EF score & BULL;NVAfc -1; the third group comprises four irrigated herbaceous crops holdings with the highest impact (between 1.37 & BULL;10-2 and 2.13 & BULL;10-2 EF score & BULL;NVAfc -1); and the last group corresponds to the holdings with economic losses (mostly herbaceous and two Mediterranean perennial crops). This research highlights the challenge of improving the competitiveness and profitability of Spanish farming. In this way, agricultural practices that generate environmental impacts without achieving their economic goals would be avoided., The authors gratefully acknowledge the Universitat Politecnica de Valencia for providing the funds for N.K. Sinisterra-Solis's research contract through Subprogram 1 (PAID-01-18), ADSIDEO - COOPERACION 2020 Program (AD2011), and the Colombian Government for funding through COLCIENCIAS.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

A Methodology for Measuring Turbocharger Adiabatic Maps in a Gas-Stand and Its Usage for Calibrating Control Oriented and One-Dimensional Models at Early ICE Design Stages

  • Serrano, J.R.|||0000-0003-0692-3917
  • Arnau Martínez, Francisco José|||0000-0003-2902-0630
  • García-Cuevas González, Luis Miguel|||0000-0001-9340-0617
  • Gómez-Vilanova, Alejandro|||0000-0002-6627-7075
  • Guilain, Stephane
  • Batard, Samuel
[EN] In this work, a methodology is proposed to standardize turbochargers testing based on measuring the maps twice: in close to adiabatic and in diathermal conditions. Along the paper, it is discussed with special detail the impact of the procedure followed to achieve said quasi-adiabatic conditions in both the energy balance of the turbocharger and the testing complexity. As a conclusion, the paper proposes a methodology which combines quasi-adiabatic tests (cold and hot gas flow) with diathermal tests (hot gas flow) in order to extract from a turbocharger gas-stand all information needed by engine designers interested in controlling or one-dimensional-modeling the internal combustion engine (ICE). The methodology is completed with a guide for calibrating said control-oriented turbocharger models in order to separate aerodynamic efficiency (adiabatic) from heat transfer (HT) losses and from friction losses in the analysis of the turbocharger performance. The outsourced calibration of the turbocharger model allows avoiding uncertainties in the global ICE model calibration, what is very interesting for turbochargers benchmarking at early ICE-turbo matching stages or for global system analysis at early control design stages., Alejandro Gomez Vilanova is partially supported through contract Subprograma 1 (PAID-01-18) of Universitat Politecnica de Valencia. This work was partially funded ayuda a Primeros Proyectos de Investigacion (PAID-06-18), Vicerrectorado de Investigacion, Innovacion y Transferencia of Universitat Politecnica de Valencia
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Design and Numerical Analysis of Flow Characteristics in a Scaled Volute and Vaned Nozzle of Radial Turbocharger Turbines

  • Tiseira, Andrés-Omar|||0000-0001-9472-2386
  • Navarro, Roberto|||0000-0003-2587-4954
  • Inhestern, Lukas Benjamin
  • Hervás-Gómez, Natalia
[EN] Over the past few decades, the aerodynamic improvements of turbocharger turbines contributed significantly to the overall efficiency augmentation and the advancements in downsizing of internal combustion engines. Due to the compact size of automotive turbochargers, the experimental measurement of the complex internal aerodynamics has been insufficiently studied. Hence, turbine designs mostly rely on the results of numerical simulations and the validation of zero-dimensional parameters as efficiency and reduced mass flow. To push the aerodynamic development even further, a precise validation of three-dimensional flow patterns predicted by applied computational fluid dynamics (CFD) methods is in need. This paper presents the design of an up-scaled volute-stator model, which allows optical experimental measurement techniques. In a preliminary step, numerical results indicate that the enlarged geometry will be representative of the flow patterns and characteristic non-dimensional numbers at defined flow sections of the real size turbine. Limitations due to rotor-stator interactions are highlighted. Measurement sections of interest for available measurement techniques are predefined., The authors disclose receipt of the following financial support for the research, authorship, and/or publication of this article: This work was partly sponsored by the program "Ayuda a Primeros Proyectos de Investigacion (PAID-06-18), Vicerrectorado de Investigacion, Innovacion y Transferencia de la Universitat Politecnica de Valencia (UPV), Spain". The support given to Ms. N.H.G. by Universitat Politecnica de Valencia through the "FPI-Subprograma 2" (No.FPI-2018-S2-1368) grant within the "Programa de Apoyo para la Investigacion y Desarrollo (PAID-01-18)" is gratefully acknowledged
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Experimental Study of the Effect of Hydrotreated Vegetable Oil and Oxymethylene Ethers on Main Spray and Combustion Characteristics under Engine Combustion Network Spray A Conditions

  • Pastor, José V.|||0000-0003-4113-4681
  • García-Oliver, José M|||0000-0002-2676-9681
  • Micó, Carlos|||0000-0001-5787-6212
  • Garcia-Carrero, Alba Andreina
  • Gómez, Arantzazu
[EN] Featured Application This work contributes to the understanding of the macroscopic characteristics of the spray as well as to the evolution of the combustion process for alternative fuels. All these fuels have been studied under the same operating conditions than diesel therefore the comparison can be made directly, leaving in evidence that some fuels can achieve a similar behavior to diesel in terms of auto ignition but avoiding one of the biggest disadvantages of diesel such as the soot formation. Moreover, the quantification of characteristic parameters such as ignition delay, liquid length, vapor penetration and flame lift-off length represent the most important data to adjust and subsequently validate the computational models that simulate the spray evolution and combustion development of these alternative fuels inside the combustion chamber. The stringent emission regulations have motivated the development of cleaner fuels as diesel surrogates. However, their different physical-chemical properties make the study of their behavior in compression ignition engines essential. In this sense, optical techniques are a very effective tool for determining the spray evolution and combustion characteristics occurring in the combustion chamber. In this work, quantitative parameters describing the evolution of diesel-like sprays such as liquid length, spray penetration, ignition delay, lift-off length and flame penetration as well as the soot formation were tested in a constant high pressure and high temperature installation using schlieren, OH* chemiluminescence and diffused back-illumination extinction imaging techniques. Boundary conditions such as rail pressure, chamber density and temperature were defined using guidelines from the Engine Combustion Network (ECN). Two paraffinic fuels (dodecane and a renewable hydrotreated vegetable oil (HVO)) and two oxygenated fuels (methylal identified as OME(1)and a blend of oxymethylene ethers, identified as OMEx) were tested and compared to a conventional diesel fuel used as reference. Results showed that paraffinic fuels and OME(x)sprays have similar behavior in terms of global combustion metrics. In the case of OME1, a shorter liquid length, but longer ignition delay time and flame lift-off length were observed. However, in terms of soot formation, a big difference between paraffinic and oxygenated fuels could be appreciated. While paraffinic fuels did not show any significant decrease of soot formation when compared to diesel fuel, soot formed by OME(1)and OME(x)was below the detection threshold in all tested conditions., This research has been partly funded by the European Union's Horizon 2020 Programme through the ENERXICO project, grant agreement no 828947, and from the Mexican Department of Energy, CONACYT-SENER Hidrocarburos grant agreement no B-S-69926 and by Universitat Politecnica de Valencia through the Programa de Ayudas de Investigacion y Desarrollo (PAID-01-18).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Development of Injection-Molded Polylactide Pieces with High Toughness by the Addition of Lactic Acid Oligomer and Characterization of Their Shape Memory Behavior

  • Lascano-Aimacaña, Diego Sebastián|||0000-0002-0996-1946
  • Ivorra-Martinez, Juan|||0000-0001-8968-4899
  • Torres-Giner, Sergio|||0000-0001-9071-9542
  • Balart, Rafael|||0000-0001-5670-7126
  • Boronat, Teodomiro|||0000-0002-2144-2874
  • Quiles-Carrillo, Luis|||0000-0001-8037-2215
  • Moraga, Giovanni
  • Rojas-Lema, Sandra Paola
[EN] This work reports the effect of the addition of an oligomer of lactic acid (OLA), in the 5-20 wt% range, on the processing and properties of polylactide (PLA) pieces prepared by injection molding. The obtained results suggested that the here-tested OLA mainly performs as an impact modifier for PLA, showing a percentage increase in the impact strength of approximately 171% for the injection-molded pieces containing 15 wt% OLA. A slight plasticization was observed by the decrease of the glass transition temperature (T-g) of PLA of up to 12.5 degrees C. The OLA addition also promoted a reduction of the cold crystallization temperature (T-cc) of more than 10 degrees C due to an increased motion of the biopolymer chains and the potential nucleating effect of the short oligomer chains. Moreover, the shape memory behavior of the PLA samples was characterized by flexural tests with different deformation angles, that is, 15 degrees, 30 degrees, 60 degrees, and 90 degrees. The obtained results confirmed the extraordinary effect of OLA on the shape memory recovery (R-r) of PLA, which increased linearly as the OLA loading increased. In particular, the OLA-containing PLA samples were able to successfully recover over 95% of their original shape for low deformation angles, while they still reached nearly 70% of recovery for the highest angles. Therefore, the present OLA can be successfully used as a novel additive to improve the toughness and shape memory behavior of compostable packaging articles based on PLA in the new frame of the Circular Economy., This research work was funded by the Spanish Ministry of Science, Innovation, and Universities (MICIU) project numbers RTI2018-097249-B-C21 and MAT2017-84909-C2-2-R. L.Q.-C. wants to thank Generalitat Valenciana (GVA) for his FPI grant (ACIF/2016/182) and the Spanish Ministry of Education, Culture, and Sports (MECD) for his FPU grant (FPU15/03812). D.L. thanks Universitat Politècnica de València (UPV) for the grant received through the PAID-01-18 program. S.T.-G. is recipient of a Juan de la Cierva contract (IJCI-2016-29675) from MICIU. S.R.-L. is recipient of a Santiago Grisolía contract (GRISOLIAP/2019/132) from GVA. J.I.-M. wants to thank UPV for an FPI grant PAID-01-19 (SP2019001). Microscopy services of UPV are acknowledged for their help in collecting and analyzing the microscopy images. Authors also thank Condensia Química S.A. for kindly supplying Glyoplast OLA 2.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Exception-sensitive program slicing

  • Galindo, Carlos|||0000-0002-3569-6218
  • Silva, Josep|||0000-0001-5096-0008
  • Pérez, Sergio
[EN] Program slicing is a technique for program analysis and transformation with many different applications such as program debugging, program specialisation, and parallelisation. The system dependence graph (SDG), the most commonly used data structure for program slicing, has been extended in several ways to manage exception handling constructs. In this paper, however, we show that the presence of exception-handling constructs can make even the extended SDG produce incorrect and incomplete slices. To solve this situation, we survey the current state of the art and merge and extend different approaches (that treat throws, try-catch, etc.) to produce a version of the SDG that is able to manage all of them, that always produces complete slices, and that increases its precision keeping the same time complexity. An interesting side result is the discovering of a new kind of control dependence: conditional control dependence, which is needed to properly represent catch statements.(c) 2022 The Author(s). Published by Elsevier Inc. This is an open access article under the CC BY-NC-ND license (http://creativecommons.org/licenses/by-nc-nd/4.0/)., This work has been partially supported by the EU (FEDER) and the Spanish MCI/AEI under grant PID2019-104735RB-C41, and by the Generalitat Valencianaunder grant Prometeo/2019/098 (DeepTrust). Sergio Perez was partially supported by Universitat Politecnica de Valenciaunder FPI grant PAID01-18. Carlos Galindo was partially supported by the Spanish Ministerio de Universidades under grant FPU20/03861 and by the Generalitat Valenciana under grant ACIF/2021/155.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Temperature-insensitive curvature sensor based on Bragg gratings written in strongly coupled multicore fiber

  • Liu, Zhiming
  • Zheng, Di
  • Villatoro, Joel
  • Antonio-Lopez, J. Enrique
  • Schülzgen, Axel
  • Amezcua-Correa, Rodrigo
  • Zou, Xihua
  • Pan, Wei
  • Madrigal-Madrigal, Javier|||0000-0003-3156-1321
  • Sales Maicas, Salvador|||0000-0001-9457-976X
[EN] A novel temperature-insensitive optical curvature sensor has been proposed and demonstrated. The sensor is fabricated by inscribing fiber Bragg gratings with short lengths into a piece of strongly coupled multicore fiber (SCMCF) and spliced to the conventional single-mode fiber. Due to the two supermodes being supported by the SCMCF, two resonance peaks, along with a deep notch between them, were observed in the reflection spectrum. The experimental results show that the depth of the notch changes with the curvature with a sensitivity up to 15.9dB/m-1 in a lower curvature range. Besides, thanks to the unique property of the proposed sensor, the notch depth barely changes with temperature. Based on the intensity demodulation of the notch depth, the temperature-insensitive curvature sensor is achieved with the cross sensitivity between the temperature, and the curvature is as low as 0.001m-1/¿C., National Natural Science Foundation of China (62071395); the 111 Project (B18045); Sichuan Province Science and Technology Support Program (2020YJ0329); Universitat Politècnica de València (PAID-01-18); Ministerio de Economía y Competitividad (PGC2018-101997-B-I00, TEC2017-88029-R).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Spatio-temporal ultrasound beam modulation to sequentially achieve multiple foci with a single planar monofocal lens

  • Pérez-López, Sergio
  • Fuster Escuder, José Miguel|||0000-0001-7778-8834
  • Candelas Valiente, Pilar|||0000-0002-9924-7673
[EN] Ultrasound focusing is a hot topic due to its multiple applications in many fields, including biomedical imaging, thermal ablation of cancerous tissues, and non destructive testing in industrial environments. In such applications, the ability to control the focal distance of the ultrasound device in real-time is a key advantage over conventional devices with fixed focal parameters. Here, we present a method to achieve multiple time-modulated ultrasound foci using a single planar monofocal Fresnel Zone Plate. The method takes advantage of the focal distance linear dependence on the operating frequency of this kind of lenses to design a sequence of contiguous modulated rectangular pulses that achieve different focal distances and intensities as a function of time. Both numerical simulations and experimental results are presented, demonstrating the feasibility and potential of this technique., This work has been supported by Spanish MICINN project number RTI2018-100792-B-I00 and Generalitat Valenciana project AICO/2020/139. S.P.-L. acknowledges financial support from Universitat Politecnica de Valencia Grant program PAID-01-18.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Tunable subwavelength ultrasound focusing in mesoscale spherical lenses using liquid mixtures

  • Pérez-López, Sergio
  • Minin, Igor V.
  • Minin, Oleg V.
  • Fuster Escuder, José Miguel|||0000-0001-7778-8834
  • Candelas Valiente, Pilar|||0000-0002-9924-7673
[EN] In this work, we present a configurable spherical lens for underwater focusing applications, which consists on a hollow ABS container filled with a liquid mixture. Two miscible liquids with different sound speeds are required to implement this novel configurable lens. We show that by adjusting the mixing ratio between the volumes of both liquids, the sound speed of the liquid mixture can be accurately selected. This results in a modification of the acoustic jet properties and a continuous tuning on the lens focal length. This procedure can be fully automatized providing a dynamic control mechanism that can shift the lens focal length to any desired value inside a continuous range in both directions. Depending on the acoustic properties of the selected liquids, subwavelength resolution or even beyond the diffraction limit resolution can be achieved. We provide experimental measurements for ethanol-water mixtures achieving subwavelength resolution for a certain focal length ranging between 34.6 and 42.8 mm., This work has been supported by Spanish MINECO TEC2015-70939-R and MICINN RTI2018-100792-B-I00 projects. S.P.-L. acknowledges financial support from Universitat Politecnica de Valencia grant program PAID01-18. I.V.M. and O.V.M. acknowledge support from the Tomsk Polytechnic University Enhancement Program.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Detection, molecular characterisation and aspects involving the transmission of tomato chlorotic dwarf viroid in eggplant

  • Gramazio, Pietro|||0000-0003-2226-7999
  • Lerma Lerma, María Dolores|||0009-0003-5404-1609
  • Villanueva-Párraga, Gloria|||0000-0002-1475-2882
  • Vilanova Navarro, Santiago|||0000-0003-4939-9713
  • Figás-Moreno, María Del Rosario
  • Arrones-Olmo, Andrea|||0000-0003-3926-0291
  • San Bautista Primo, Alberto|||0000-0003-4846-6611
  • Soler Aleixandre, Salvador|||0000-0001-8325-3326
  • Prohens Tomás, Jaime|||0000-0003-1181-9065
  • Plazas Ávila, María de la O|||0000-0001-8090-7312
  • García-Fortea, Edgar
  • Mangino, Giulio
  • Alonso-Martín, David
[EN] Tomato chlorotic dwarf viroid (TCDVd) is a pospiviroid that causes severe disease symptoms in tomato. TCDVd is also naturally found in other crops and plants, in most occasions being asymptomatic. Apart from the natural hosts reported up to now, artificial inoculations have revealed that TCDVd can infect other plants, including eggplant (Solanum melongena). In a screening of seedlings of eggplant from a breeding programme we detected a pospiviroid, which we identified as TCDVd, representing the first report of natural infection of eggplant by TCDVd. The new TCDVd isolate of eggplant was detected by reverse transcription polymerase chain reaction (RT¿PCR) using primers TG21/CT20, initially designed to detect potato spindle tuber viroid. The new isolate sequence is close to a Brugmansia sanguinea isolate of TCDVd from the Netherlands, and most of the nucleotidic changes with respect to this isolate and to the reference genome sequence of TCDVd are found in the TR region. Naturally infected plants of eggplant with this TCDVd isolate did not display any disease symptoms. We demonstrated that in eggplant TCDVd is mechanically transmitted with low to moderate efficiency with cultivation practices, but not by plant¿to¿plant contact. Tomato plants artificially inoculated with the eggplant isolate of TCDVd tested positive for the presence of the viroid at 50¿days after inoculation, but did not display any disease symptoms. Seed transmission to germinated seedlings of eggplant was variable among progenies from infected plants, ranging from 7.7% to 100.0%. Disinfection of seeds with chemical treatments with sodium hypochlorite and trisodium phosphate solutions plus thermotherapy at 80°C for 24¿hr or 90°C for 6 hr was ineffective in reducing the rate of transmission by seed. We did not find evidence of horizontal transmission of TCDVd by pollen, but vertical transmission was highly efficient when healthy eggplant plants were pollinated with infected pollen. Our results indicate that asymptomatic infection of eggplant by TCDVd and high seed and pollen transmission rates may contribute to the spread of this viroid. The information we obtained is useful in order to implement measures for the prevention, control and eradication of TCDVd in eggplant crops, as well as to avoid their transmission to other hosts., P.G. is grateful to Universitat Politècnica de València and to Japan Society for the Promotion of Science for their respective postdoctoral grants (PAID-10-18 and FY2019 JSPS Postdoctoral Fellowship for Research in Japan [Standard]). A.A. and D.A. are grateful to Universitat Politècnica de València for their respective predoctoral (PAID-01-18 and PAID-01-16) contracts within the Programa de Ayudas de Investigación y Desarrollo initiative. E.G.-F. is grateful to Ministerio de Educación, Cultura y Deporte para la Formación de Profesorado Universitario for a predoctoral grant (FPU17/02389). G.M. is grateful to Generalitat Valenciana for a predoctoral grant within the Santiago Grisolía programme (GRISOLIAP/2016/012). M.P. is grateful to Generalitat Valenciana and Fondo Social Europeo for a postdoctoral grant (APOSTD/2018/014).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Bifocal Ultrasound Focusing Using Bi-Fresnel Zone Plate Lenses

  • Pérez-López, Sergio
  • Fuster Escuder, José Miguel|||0000-0001-7778-8834
  • Candelas Valiente, Pilar|||0000-0002-9924-7673
  • Tarrazó-Serrano, Daniel|||0000-0001-9986-0884
  • Castiñeira-Ibáñez, Sergio|||0000-0001-6414-3906
  • Rubio Michavila, Constanza|||0000-0002-4395-7473
[EN] In this work, we present a bifocal Fresnel zone plate (BiFZP) capable of generating focusing profiles with two different foci. The performance of the BiFZP is demonstrated in the ultrasound domain, with a very good agreement between the experimental measurements and the finite element method (FEM) simulations. This lens becomes an appealing alternative to other dual-focusing lenses,in which the foci location can only be set at a limited range of positions, such as M-bonacci zone plates. Moreover, the variation of the operating frequency has also been analyzed, providing an additional dynamic control parameter in this type of lenses., This work was supported by the Spanish MICINN RTI2018-100792-B-I00 project. S.P.-L. acknowledges financial support from the Universitat Politècnica de València grant program PAID-01-18. D.T.-S. acknowledges financial support from the MICINN BES-2016-07713 project.